special report – load bed systems for modern military vehicles

20
Load Bed Systems for Modern Military Vehicles SPECIAL REPORT Load Bed Systems for Modern Military Vehicles Evolving in a Changing World Military Load Bed Technology Faces Real Challenges Less Specialisation Means More Capability Meeting Current Needs Sponsored by Published by Global Business Media

Upload: the-magazine-production-company

Post on 30-Jan-2016

227 views

Category:

Documents


0 download

DESCRIPTION

Defence Industry – Special Report on Load Bed Systems for Modern Military Vehicles

TRANSCRIPT

Page 1: Special Report – Load Bed Systems for Modern Military Vehicles

Load Bed Systems for Modern Military Vehicles

S P E C I A L R E P O R T

Load Bed Systems for Modern Military Vehicles

Evolving in a Changing World

Military Load Bed Technology Faces Real Challenges

Less Specialisation Means More Capability

Meeting Current Needs

Sponsored by

Published by Global Business Media

Page 2: Special Report – Load Bed Systems for Modern Military Vehicles

AgilityQuality

Integrity

Vehicle IntegrationVehicle RegenerationVehicle ConfigurationThrough Life Support

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 [email protected]

ww

w.m

arsh

all-

ls.c

om

Vehicle Engineering

A Marshall Land Systems Company

MVE A4 Advert May_Layout 1 17/05/2012 15:54 Page 1

Page 3: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

Published by Global Business Media

Global Business Media Limited 62 The Street Ashtead Surrey KT21 1AT United Kingdom

Switchboard: +44 (0)1737 850 939 Fax: +44 (0)1737 851 952 Email: [email protected] Website: www.globalbusinessmedia.org

PublisherKevin Bell

Business Development DirectorMarie-Anne Brooks

EditorJohn Hancock

Senior Project ManagerSteve Banks

Advertising ExecutivesMichael McCarthyAbigail Coombes

Production ManagerPaul Davies

For further information visit:www.globalbusinessmedia.org

The opinions and views expressed in the editorial content in this publication are those of the authors alone and do not necessarily represent the views of any organisation with which they may be associated.

Material in advertisements and promotional features may be considered to represent the views of the advertisers and promoters. The views and opinions expressed in this publication do not necessarily express the views of the Publishers or the Editor. While every care has been taken in the preparation of this publication, neither the Publishers nor the Editor are responsible for such opinions and views or for any inaccuracies in the articles.

© 2012. The entire contents of this publication are protected by copyright. Full details are available from the Publishers. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise, without the prior permission of the copyright owner.

ContentsForeword 2John Hancock, Editor

Load Bed Systems for Modern Military Vehicles 3Marshall Vehicle Engineering Limited

Background and CredentialsWheeled Logistic SystemsLoad System Options EPLS ISO Skeletals Loadbeds and Cargo Bodies Low or Zero Torsion Load Carrying Systems Low Torsion Zero Torsion Vehicle Mounted Mechanical Handling EquipmentContacts

Evolving in a Changing World 8Peter Dunwell, Staff Writer

Driven by ChangeAll War is a BattleMulti-Task not SpecialistStandardisation

Military Load Bed Technology Faces Real Challenges 10John Hancock

A Challenging Working EnvironmentEngineering SolutionsMilitary NeedsA Collaborative Production Process

Less Specialisation Means More Capability 12Francis Slade, Defence Correspondent

Engineering DevelopmentsSpecifi cation and CostSupply Chain and Management DevelopmentsA More Standardised Future

Meeting Current Needs 14Peter Dunwell, Staff Writer

Learning from AmateursAdapting to ChangeFlexibility, Speed and StandardisationNext Generation

References 16

WWW.DEFENCEINDUSTRYREPORTS.COM | 1

Load Bed Systems for Modern Military Vehicles

S P E C I A L R E P O R T

Load Bed Systems for Modern Military Vehicles

Evolving in a Changing World

Military Load Bed Technology Faces Real Challenges

Less Specialisation Means More Capability

Meeting Current Needs

Sponsored by

Published by Global Business Media

Page 4: Special Report – Load Bed Systems for Modern Military Vehicles

Foreword

This Special Report looks at load beds, the

adaptable systems which perform multiple

tasks and can be fi tted onto any one of a large

fl eet of standardised vehicles (chassis-cab units)

or even onto ostensibly combat vehicles.

The Report opens with an article that traces the

changes in demands placed on military wheeled

logistic vehicles over the last 20 years, particularly in

light of asymmetric operations in Iraq and Afghanistan.

There is an obvious need to provide logistic vehicles

with signifi cantly improved crew protection while, at

the same time, they must negotiate increasingly more

demanding physical terrain. Marshall Land Systems,

of which Marshall Vehicle Engineering is a part, has

been established since 1946 and is at the forefront

in the manufacture of military vehicle load beds,

fl atracks and logistic handling systems. The article

goes on to describe a number of options available,

their advantages and disadvantages.

In terms of the equipment they need, commercial

vehicle operators might be said to have it easy. Easy

in the sense that they know where their vehicles will

be running and what they will be carrying. Thus, an

operator hauling aggregates for the construction

industry will use a six or eight wheeled rigid tipper

vehicle capable of running on unmade roads while

a supermarket chain will use a fl eet of curtain sided

trailers hauled by heavy tractor units, built for fast

running on motorways and manoeuvring in loading

areas. A fi re brigade will order… fi re engines. It isn’t

that straightforward for military operators.

In the fi rst place, they have to deliver materials and

loads into war zones that are less easily defi ned

these days: where even logistics vehicles can

be subject to the rigours and threats which have

previously been more the working environment for

combat and engineering vehicles. Then they have

to carry an enormous variety of loads (possibly

aggregates and groceries but also arms, ammunition,

communications equipment, smaller and disabled

vehicles … even fi re fi ghting equipment) but do not

know in advance precisely how much of each might

be needed for any given operation.

In the past, this broad requirement would be

addressed by ordering fl eets of every possible type

of vehicle that might be needed and then storing them

‘just in case’. Today that isn’t possible fi nancially, and

new requirements are emerging too rapidly; so a new

way of organising military transport has to evolve. At

its heart, is the load bed, which has highly versatile

capabilities in both commercial and military situations.

It is this often unsung but vital link in the chain of

military capability that we address, in its varying forms

and applications, in the pages that follow.

John HancockEditor

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

2 | WWW.DEFENCEINDUSTRYREPORTS.COM

John Hancock joined as Editor of Defence Reports in early 2012. A journalist for nearly 25 years, John has written and edited articles and papers on a range of defence, engineering and technology topics as well as for key events in the sector. Subjects have included aero-engineering, testing, aviation IT, materials engineering, weapons research, supply chain, logistics and naval engineering.

Page 5: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

WWW.DEFENCEINDUSTRYREPORTS.COM | 3

AgilityQuality

IntegrityVehicle Integration

Vehicle Regeneration

Vehicle Configuration

Through Life Support

www.marshall-ls.com

Vehicle Engineering

A Marshall Land Systems Company

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 717921

[email protected]

Load Bed Systems for Modern Military Vehicles Marshall Vehicle Engineering Limited

Background and CredentialsDating back to 1946, Marshall Land Systems has a strong pedigree and substantial experience in the manufacture of Military vehicle loadbeds, fl atracks and logistic handling systems. Since this date, the Marshall group has been involved in the design and manufacture of in excess of 80,000 units in conjunction with a range of chassis cab manufacturers and end users both in the UK and overseas.

As part of Marshall Land Systems, Marshall Vehicle Engineering (MVE) now holds the responsibility within the group for vehicle engineering, becoming a centre of excellence for loadbeds, fl atracks and logistic handling systems.

The state of the art MVE facility at Mildenhall has been specifi cally established for the design, engineering and manufacture of loadbeds, cargo bodies and their ancillary equipment. Amongst other capabilities, the Mildenhall facility boasts robotic welding, a zinc phosphate and e-dip finishing plant, painting booths, waxing and assembly facilities.

Following selection as a key supporting sub-contract partner for the provision of 6,600 loadbeds for the UK MoD Support Vehicle Programme, MVE has worked closely with the UK MoD and the OEM Prime Contractor to design and engineer the full range of cargo bodies required to transport in excess of 650 defi ned

loads on a range of chassis configurations. In satisfying the diverse requirements of the programme, MVE undertook activities including extensive fi nite element analysis and a full test and validation programme to satisfy both the Prime Contractor and the UK MoD.

In parralell with the Support Vehicle Programme, MVE has worked closely with a number of Prime Contractors pursuing overseas contracts and in 2009 produced the load beds for the UK MoD Wolfhound UOR Programme. In fulfilling this contract, first delivery was achieved in just 8 weeks after placement of the production order, a feat that clearly demonstrates MVE’s abilities to deliver turn-key solutions rapidly to clients.

Wheeled Logistic SystemsThe demands placed on military wheeled logistic vehicles have changed substaintially over the course of the last 20 years and particularly so over the course of the last decade. Cold War planning assumptions called for quick and efficient deployment of materiel and, where possible, a seamless interface between strategic, operational and tactical delivery means. In parrallel, detailed analysis of terrain conditions and the anticipated operating environment led to NATO mobility models and carefully defi ned doctrinal requirements.

DESIGNED TO CARRY OVER 650 LOAD TYPES, MVE’S LOAD BEDS MAKE A RANGE OF VEHICLES FIT FOR ROLE.

Page 6: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

4 | WWW.DEFENCEINDUSTRYREPORTS.COM

A failure to integrate the

loadbed to the vehicle

correctly will reduce

the performance of the

vehicle as a ‘system’

and could lead to

catastrophic failure of

either the loadbed or the

vehicle chassis.

Asymmetric operations in Iraq and Afganistan have led to two notable doctrinal changes. The fi rst and most obvious is the need to provide logistic vehicles with significantly improved crew protection systems and secondly, the need for both operational and tactical logistic vehicles to negoitiate increasingly more demanding physical terrain because of the lack of, and risks attached to using, existing tracks. An appreciation of the effect cross country operation has on the payload, be it broken bulk stores or a ridgid body such as an ISO container or shelter, is the key skill required of the military logistic vehicle body builder and MHE integrator. A failure to integrate the loadbed to the vehicle correctly will reduce the performance of the vehicle as a ‘system’ and could lead to catastrophic failure of either the loadbed or the vehicle chassis.

The commercial sector has similarly witnessed several signifi cant developments in the way in which commodities are moved and handled. This has included a development and growth in the use of vehicle mounted mechanical handling equipment such as cranes, tail lifts and vehicle mounted fork lift trucks with which labour costs and point of delivery turn round times can be substantially reduced. Similarly, Intermodal or ISO containers have become the standard international shipping unit whether 10’, 20’ or 40 ‘ ISO containers all of which are now routinely encountered within forward military units.

Cold War ammunition resupply studies demonstrated the inability to move and handle the quantity of palletised materiel, particulary artillery ammunition, using the equipment and techniques then employed, from depots to

forward deployment positions within the time available. This led to a series of innovative studies and the adoption of Palletised Load handling Systems such as the British DROPS system. Now widely used by a large number of different military users, such systems have demonstrated their utility and flexibility leading to a far wider range of uses than was initially anticipated including the carrage of ISO containers.

The requirement to operate logistic vehicles wearing CBRN and cold weather protective clothing has been a feature of military procurement for many years. From an equipment perspective, however, this necessitates both hot and cold chamber testing and frequently, the need to ‘water proof’ the equipment for amphibious operations.

As such, although frequently based on a commercially available drive train and chassis, the modern military logistic vehicle is required to satisfy substantially more demanding criteria than is the case for its commercial equivalent. That said, the military user is well advised to keep an eye on the developments taking place within the commercial sector in order to reduce operating costs but, above all, the deployed logistic foot print.

Load System OptionsDue to the ever changing complexity of logistical requirements, several Load carrying systems are currently available for military vehicles, each with their particular advantages and merits. This article aims to outline the advantages and disadvantages of each.

MVE’S SKILL SETS ALLOW FOR RAPID PROTOTYPING AND PRODUCTION FOR NUMEROUS CHASSIS TYPES.

Page 7: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

WWW.DEFENCEINDUSTRYREPORTS.COM | 5

AgilityQuality

IntegrityVehicle Integration

Vehicle Regeneration

Vehicle Configuration

Through Life Support

www.marshall-ls.com

Vehicle Engineering

A Marshall Land Systems Company

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 717921

[email protected]

EPLSModern military vehicles commonly use palletized load handling systems, utilising a hookloader or container handling unit permanently mounted to vehicles.

Where there is a requirement to be able to quickly pick up and drop the load off without further mechanical handling equipment, these systems are particularly effective in moving pre-defi ned loads whether fuel, ammunition or other ISO containerised loads.

The principal weaknesses are the wieght of the load handling system, the weight of the fl at rack if required and the inability to deliver part loads. The speed and fl exibility of the equipment makes PLS systems ideally suited to strategic and operational logistic vehicles and, with the appropriate level of mobility, a large number of tactical applications.

ISO Skeletals In the event that ISO or ISO compatible shelters are specifically required to be carried, and assuming MHE is available to lift the container on and off the vehicle when required, it is possible to employ an ISO Skeletal frame. Typically this is in the form of an H-frame system with a longitudinal spine that is mounted to the vehicle chassis with cross members either set at, or movable to, the correct pitch for the specifi c ISO Container.

Twistlocks are used to quickly and firmly connect the ISO container to the frame. These allow the ISO container to be quickly, simply and firmly attached to the vehicle. There are various types of twistlock available dependant upon the user needs and national road regulations. Typically, military specification

twistlocks include a lock down mechanism to clamp the container to prevent movement and noise whilst travelling across rough terrain.

ISO skeletals can be either rigidly mounted to the vehicle, or mounted using a zero torsion system depending on the mobility requirements placed on the vehicle system.

The key advantage of an ISO Skeletal system is that it provides appropriate support for the ISO container at the minimum possible parasitic weight and at low cost. The principle disadvantage is that it has little or no fl exibility of use unless it is provided with an auxiliary load carrying platform that can be mounted upon the ISO twistlocks in place of the ISO container. If required, there are potential operational constraints surrounding the availability of the load carrying platform once vehicles are deployed. Nonetheless, this approach is gaining favour in a growing number of countries due to the widespread use of ISO containers and weight/cost savings.

Loadbeds and Cargo Bodies The use of loadbeds and cargo bodies present an alternative to EPLS and ISO skeletals due to inherent fl exibility of load carriage, particularly applicable to loads of loose or mixed cargo.

Available in a number of system designs, loadbeds and cargo bodies provide a flat platform that normally include a number of lashing and tiedown points and increasingly ISO twistlocks allowing the user to mount ISO containers on the loadbed. These sytems can be provided as a fl atbed with a clear deck that is open to the elements, or with hinged dropsides and tailgate, a superstructure and cover or a sliding roof.

THROUGH ZINC-PHOSPHATE AND E-COAT TREATMENT,

PREVENTION OF LOAD BED CORROSION IS SIGNIFICANTLY ENHANCED.

Page 8: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

6 | WWW.DEFENCEINDUSTRYREPORTS.COM

A typical zero torsion

design always includes

a fi xed mounting to the

chassis at a certain

point. This retains the

platform and the load,

stops the load from

moving and tilting and

retains side to side and

fore and aft loads.

Loadbeds and cargo bodies can be built and subsequently confi gured to match and optimise the chassis dimensions and characteristics across a fl eet of vehicles. They offer the user a high level of flexibility and stretch potential allowing the uUser to carry any existing and foreseeable equipment, stores or personel.

Low or Zero Torsion Load Carrying SystemsThere are two mounting and operating systems available for integrating loadbeds with the chassis known as low torsion mounting and zero torsion (or torsion free) mounting.

Selection of either variant should be considered with regard to the performance required from the chassis, transport requirements, constraints placed upon the equipment and the loads to be carried.

In each case, the condition that is considered most critical is that of the twisting that is imparted into the vehicle chassis when it is driven over uneven undulating ground. In considering a typical worst case, it may be feasible for 300mm+ of wheel elevation to occur at each axle, with these being diagonally opposite from front to back. In such circumstances substantial twist can occur in the chassis rails. A proportion of the stress resulting from this torsion is then transferred to the load platform that is mounted upon the chassis.

Low Torsion The low torsion loadbed design features bearers that run across the loadbed and support the load being mounted above whilst connected by carefully designed and stressed connecting webs to a pair of longitudinal runners. In turn, these runners sit upon and are fi rmly attached to the chassis rails.

In the case of MVE low torsion loadbeds, springs are fi tted as part of the front mounting brackets permitting a degree of compliance under maximum chassis twist to reduce the movement and induced stress. In this configuration the loadbed supports the chassis and will reduce the level of twist imparted to it.

In many cases and certainly if vehicles and ISO Containers are carrying loose loads, the impact upon the load being carried is negligible, and if the loadbed and chassis are optimized, the effect will be within design and operational limits.

Zero Torsion A typical zero torsion design always includes a fi xed mounting to the chassis at a certain point. This retains the platform and the load, stops the load from moving and tilting and retains side to side and fore and aft loads.

A pivot is integrated at the front and/or at the rear, positioned to transmit key loads as directly as possible to the subframe/chassis whilst permitting the subframe and chassis to twist, bend and defl ect freely. This approach typically:1) Reduces the torsional loadings into the

payload – which is important when carrying delicate equipment. However, it should be recognised that it is not possible to isolate completely torsional loading from an ISO mounted container as it twists at the middle outwards when subjected to centripetal forces such as those encountered when cornering at speed.

2) Allows the chassis greater fl exibility, but by the same token does not support the chassis to the same extent as the low torsion system. A zero torsion system typically allows greater axle defl ection in severe off-road conditions,

AN MVE ZERO TORSION LOAD BED READY FOR INSTALLATION TO THE VEHICLE CHASSIS.

Page 9: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

WWW.DEFENCEINDUSTRYREPORTS.COM | 7

AgilityQuality

IntegrityVehicle Integration

Vehicle Regeneration

Vehicle Configuration

Through Life Support

www.marshall-ls.com

Vehicle Engineering

A Marshall Land Systems Company

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 717921

[email protected]

reducing differential and tyre loadings and, to some extent, ground pressure. This can contribute to vehicle and load mobility.

Zero torsion systems can therefore offer improved vehicle system performance, particularly for delicate loads and when negotiating severe cross country terrain. However, they are typically heavier, have a deck that is higher above the chassis than a low torsion equivalent and are more expensive than the low torsion alternative.

Vehicle Mounted Mechanical Handling EquipmentA wide range of vehicle mounted cranes is available from several established suppliers. However reach and lift capacity varies signifi cantly. Nonetheless, they allow the vehicle crew to load and unload materiel unassisted. This increases operational fl exibility and reduces turnaround times and, subsequently, the deployed operational foot print by reducing the number of MHE and operators that need to be deployed.

Tail lifts have not been widely adopted by most military users. Available in a wide variety of configurations with a manual back-up capability, they offer a tried and tested solution to the distribution of materiel and are particularly suitable to the rapid and efficient distribution of equipment and materiel amongst forward units, reducing man power requirements and speeding up operations without reducing levels of tactical mobility.

Contacts

For further information or guidance please contact:

Simon HughesMarshall VE [email protected]: +44 (0) 1223 373046 Fax: +44 (0) 1223 373414Mob: +44 (0) 7768 467372 Peter HardistyMarshall [email protected]: +44 (0) 01223 372616 Fax: +44 (0) 1223 373414Mob: +44 (0) 7721956757

Page 10: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

8 | WWW.DEFENCEINDUSTRYREPORTS.COM

Evolving in a Changing WorldPeter Dunwell, Staff Writer

As military imperatives change, load bed technology and capability must also evolve to continue to deliver, in every sense

Driven by ChangeSince World War II and the Cold War that followed, the conduct of warfare has evolved; from known enemies, identifiable frontlines and symmetric fighting styles into insurgencies and all-theatre asymmetric war with no easily identifi able enemy. And changes have not only affected battlefield operations. Women have served in military roles for more than a century but whereas once those roles were limited to nursing, catering, administration and other ‘behind the lines’ tasks, including driving, they are now active right across the armed services and particularly so in logistics and the supply chain throughout theatres of war.

One obvious impact this has had on the requirements for load beds is that they should be able to be operated by smaller and lighter personnel; for instance, the weight of side boards and tail boards have to be reduced and yet must be able to bear the increased weight of individual personnel wearing body armour and carrying very large packs and weapons. Better designed frameworks and advanced materials such as composite fl oors

can contribute to this but, in a world of constantly evolving warfare methodologies, the comfort of ‘here to stay for a while’ technologies is defi nitely a thing of the past.

All War is a BattleAlso, in asymmetric warfare without frontlines, it is diffi cult to separate equipment that needs to be battle-proof and equipment that only needs to be capable to operate behind the lines, because there is no ‘behind the lines’. As John Reeve, Director and Consultant at Araldo Ltd explains:

“the campaigns in Iraq and Afghanistan have resulted in the procurement of signifi cant new capabilities for UK forces operating in the land environment. Traditional capabilities born out of Cold War requirements, such as tanks, tracked armoured personnel carriers and unprotected utility vehicles, have found themselves all but redundant as protected mobility fl eets have come to the fore.”1

With logistics resources as likely to be attacked as combat resources, load beds must also incorporate the kind of protection technologies that are used on driving cabs and other areas containing personnel. The other side of this coin is that a number of combat vehicle platforms also have to be adapted to carry loads into the most hostile conditions. That is not so new, with versions of battle tanks having, in the past, been adapted as bridging machines and other engineering equipment, but today’s combat vehicles have to deal with such varied and exotic threats that units like the latest Royal Engineers’ vehicles in the British army bear more than passing resemblance to the fi ghting vehicles alongside which they often operate.

The operation of ‘support’ vehicles in near battle conditions poses yet further challenges for load bed manufacturers. Designing and building load platforms for vehicles like the British

The weight of side

boards and tail boards

have to be reduced and

yet must be able to bear

the increased weight

of individual personnel

wearing body armour

and carrying very large

packs and weapons.

MVE SUPPORTS A NUMBER OF INTERNATIONAL VEHICLE OEMS IN THE

DESIGN AND PROVISION OF LOAD BEDS AND CARGO CARRYING SYSTEMS.

Page 11: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

WWW.DEFENCEINDUSTRYREPORTS.COM | 9

AgilityQuality

IntegrityVehicle Integration

Vehicle Regeneration

Vehicle Configuration

Through Life Support

www.marshall-ls.com

Vehicle Engineering

A Marshall Land Systems Company

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 717921

[email protected]

Army’s Wolfhound tactical support vehicle to enable this battlefi eld vehicle to carry both loose and palletised loads2 is a good example of how much demands on load beds have changed to meet evolving military requirements. And, when operating in those sort of conditions, loading and unloading pose particular challenges for which systems such as DROPS (Demountable Rack Offload and Pickup System)3 and PLS (Palletized Load System)4 have been developed.

Multi-Task not SpecialistOne thing that hasn’t changed is the enormous variety of loads transported on military vehicles. But whereas in the past the military would often specify a very particular design for a very singular purpose, which often left excellent quality but little used vehicles spending years in storage, these days the aim is for a fairly standardised fl eet of vehicles but with load beds able to cope with or adapt to any present or future possibilities. When producing the specification for the new generation of military support vehicles currently in production, the UK MoD identifi ed in excess of 570 types of load which load beds would have to be equipped to carry. To give a flavour of the scope, the list ranged f rom fo rk l i f t t rucks to barbecues for the Officers’ Mess and Land Rovers, as well as the ubiquitous ISO container and the earlier non-ISO military container still in regular use by the forces, plus palletised loads such as ammunition. Load bed structures have become considerably more complex in order to cope with a greater range of potential operational

threat, the blurring between battle lines and supply lines, challenging terrain, and a much wider range of loads.

StandardisationMilitary vehicle manufacturers have always tried to use as many components as possible from their civilian commercial lines in order to reduce costs, simplify engineering and for ease of maintenance. All of the large vehicle manufacturers in Europe who also supply military vehicles do this and it means that load bed manufacturers have to master a wide range of engineering platforms in order for their products to operate properly.

These evolving military vehicle requirements also drive many of the key issues that engineers need to consider when choosing load bed systems for modern military vehicles. They also need to take into account the capabilities and features of the various chassis and units available to the military. Vehicle manufacturers such as Iveco Defence Vehicles, Mercedes-Benz, MAN and Oshkosh all work with specialist engineering groups to develop body builder guidelines. And in a world where the rapid deployment of armed forces is a critical element of war fi ghting, vehicles and load beds need to be capable of being loaded onto and transported by other carrier systems such as military cargo aircraft and trains, within the international loading gauge. Also, with some other loads being exceptionally heavy (battle tanks at 70 tons or more) it must be possible to transport them without undue damage to the roads over which they are carried. The requirements on military load beds are many and challenging.

TWO VARIANTS OF THE UK MOD SUPPORT VEHICLE AWAITING DELIVERY FROM THE MVE MILDENHALL FACILITY.

Page 12: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

10 | WWW.DEFENCEINDUSTRYREPORTS.COM

When the military is

delivering materials,

the route is often far

from a smooth metalled

surface, creating

tremendous lateral

and vertical distortions

that no commercial

operator would ever

expect to encounter.

Military Load Bed Technology Faces Real Challenges John Hancock

A Challenging Working EnvironmentMilitary logistics have to work in conditions that most civilian commercial operators would never encounter. Civilian commercial trucks run along largely fl at and continuous metalled surfaces from loading to delivery. And yet, one of the more frequently seen reasons for traffi c disruption is that a vehicle has shed its load. The load may be unevenly distributed and/or the vehicle’s suspension can transfer any contour variations to take the load beyond tipping point in extreme cases. Also, one of the most frequent commercial loads, the ISO container, is a rigid structure and quite infl exible so that any shock to the vehicle will tend to be all transmitted to the suspension and chassis.

Engineering SolutionsThe military is also a large user of ISO containers or ISO compliant skeletons within which varied

loads can be fitted; but when the military is delivering materials, the route is often far from a smooth metalled surface, creating tremendous lateral and vertical distortions that no commercial operator would ever expect to encounter. Hence, a key part of military logistical supply chain is in the design, quality and capability of load beds. The challenge is how to stop distortion from being transferred to the load to cause tipping. Part of that can be achieved through specialist suspension and part by allowing some movement in the chassis, but a great deal of the technology is in the engineering and fi tting of the load bed. As Andrew Bucknall, UK Area Manager at Iveco Defence Vehicles puts it:

“in theory there is no difference between the requirements tasks and demands for military as opposed to civilian [logistics] vehicles. But in practice, military vehicles are usually owned a lot longer than civilian vehicles and have to be capable of a much wider range of tasks.”

There are numerous technology solutions that help to overcome harsh environments and diffi cult conditions

LOAD BEDS ACCOMPANIED WITH VEHICLE MOUNTED MECHANICAL LIFTING

EQUIPMENT SIGNIFICANTLY REDUCES LABOUR COST AND TURNAROUND TIME.

Page 13: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

WWW.DEFENCEINDUSTRYREPORTS.COM | 11

AgilityQuality

IntegrityVehicle Integration

Vehicle Regeneration

Vehicle Configuration

Through Life Support

www.marshall-ls.com

Vehicle Engineering

A Marshall Land Systems Company

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 717921

[email protected]

There are two recognised ways to address these problems. The first is known as a low torsion load bed in which the structure of the load bed is allowed to flex but without transmitting that fl exing to the load or container that it carries: this is achieved through a special arrangement of springs and slip rings. The other is a zero torsion load bed where the load bed does not fl ex at all but is allowed to pivot (around a central connection running the length of the vehicle) to maintain load orientation. A zero torsion load bed is, however, heavier, higher and more expensive than a low torsion type, reducing the load that can be carried and making it diffi cult for the vehicle to be put onto an aeroplane or fi t the load gauge of a train, or even to fi t under some bridges.

Also, military load beds often have to collect or deliver loads without the aid of infrastructure support such as the overhead cranes that handle ISO containers at ports and rail heads. To cope with this, military vehicle and load bed manufacturers use a system known as DROPS (Demountable Rack Offload and Pickup System)5 in which the load bed includes mechanism and fittings to either offload to the rear of the vehicle or on to a rail flatbed to the side. DROPS can operate with ISO containers or with a special system known as Flat Racks on which various loads can be pre-loaded for DROPS fitted vehicles. DROPS can also tow a trailer to improve driver productivity. US forces use a similar load bed technology known as Palletized Load System (PLS) based on 10x10 Oshkosh power units and fitted trailers. For all sorts of reasons, there is a long-term trend towards mechanised handling with fewer soldiers available to handle loads and with more female soldiers fulfilling logistics functions.

Military NeedsThere are a lot of other special needs that military vehicles and load beds need to match such as having to be tested for EMC (Electromagnetic Compatibility). They need to be particularly robust in structure and technology so that they can wade through significant depths of water (up to 1m deep in one current MoD requirement) as well as operating in extreme climatic conditions. Also, exceptional levels of stability are needed, especially the ability to operate on a side slope which puts design and engineering constraints on the centre of gravity and the suspension. And as if this were not enough, they also need to be capable of being airfreighted, i.e. to fi t through the loading doors and into the cargo bay of a C130 Hercules or Airbus A400M6 aircraft. The latest military chassis,

such as the Mercedes-Benz Zetros has been designed to fi t not only into a C130 and Transall C160 but also conforms with the international rail transport loading gauge7. Load beds, when fitted to vehicles, have to fit within these dimensions. And there are some particularly heavy demands on load beds such as the need to move 70 ton or more battle tanks into and out of theatre8. Enemies today have devised all sorts of low-cost, low-tech means of disrupting military operations so the makers of equipment, including load beds, need to take this into account.

All of this has an impact on design, engineering, materials and manufacture of military load bed systems. Andrew Bucknall again:

“We like to manage the risk by working with people who have experience of military operations [and requirements]. There is always someone who can undercut on price but quality is the key in this market.”

Another key requirement for military operations is that vehicles in modern warfare will usually need to be armoured9; even older vehicles have been retrofi tted. This all adds weight to the vehicle which means that the load bed must compensate for that extra weight without in any way compromising its loading and stability capabilities. To replicate the harsh conditions often faced by military vehicles, Iveco Defence Vehicles has tested the integrity of chassis and load beds in the gruelling Dakar Rally10.

A Collaborative Production ProcessThe demands on a military load bed are tremendous and varied. In the current contract to re-equip the UK MoD with a range of MAN vehicles, the makers of the 6700 load beds, Marshall Vehicle Engineering, had to take into account 700 load cases when designing the basic load bed as well as allow for more exotic variants such as cranes and winches11. The same fi rm is also working with Iveco in a joint bid to supply the Norwegian and Swedish Armed Forces with logistic vehicles fleets. Part of the Mercedes-Benz sales case to the military sector is that the fi rm works with a number of other engineering organisations to create trucks able to undertake all the tasks that military user require.

And it isn’t just with large vehicles that load bed technology is important – smaller vehicles such as the All-Terrain Mobility Platform (ATMP) ‘Supacat’ are also fi tted with specialist load beds to carry military loads.

The technology of military load beds is a critical component in the ability of forces to operate in whatever conditions they face.

Page 14: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

12 | WWW.DEFENCEINDUSTRYREPORTS.COM

Costs are reduced

wherever standard

commercial components

can be used in the

building of military

vehicles and, in this,

developments in

load bed technology

– weight reduction

technical simplifi cation

and standardisation to

commercial protocols –

can impact signifi cantly

Less Specialisation Means More Capability Francis Slade, Defense Correspondent

Load bed technology is impacting a number of areas in the military logistics supply chain and, at the same time, is itself being affected by developments in that chain. In particular, while in many ways military supply chains operate in quite different conditions to those encountered by civilian commercial supply chains, in other ways the logic that is changing all supply chains and the equipment that they employ applies equally to military conditions.

Engineering DevelopmentsMany of the changes that have taken place in load bed technology relate to engineering developments such as more effi cient design, lighter and stronger construction, use of new materials like composites and the inclusion of additional equipment to support continuing mechanisation of load handling and a reduction in the numbers of personnel available to operate in the supply chain. One such development would be to incorporate the kind of load handling device made by Hiab Cargo Technology Cranes12; integrated load handling equipment which has made loading to and offl oading from vehicles much easier.

Also, developments in suspension, tyres, axles and drive lines are often designed to make best use of the load bed technology available; hence the often distinct appearance of military logistics vehicles. Mercedes-Benz for instance highlights that its, “range of military vehicles stands out by meeting military standards and technical specifications, such as all-wheel-drive with single tyres, supreme off-road mobility, ballistic protection, air and rail transportability, fording depths up to 1 195 mm, blackout lighting system, roof hatch, tyre pressure control, etc.”13. Other military requirements that, while not specifi cally driven by load bed technology, are part of the overall stability package include the ability to run without one or more of the wheels or axles. And, of course, all of those military requirements such as armour plating and blast proofing plus crew

survivability add weight which, in turn, will reduce the payload on the load bed unless that bed can be engineered to compensate for the additional weight. Many of the developments in load bed technology demand greater power and capability for no greater weight from vehicle manufacturers.

Specifi cation and CostIt is also the case that costs are reduced wherever standard commercial components can be used in the building of military vehicles and, in this, developments in load bed technology – weight reduction technical simplifi cation and standardisation to commercial protocols – can impact significantly on the cost and engineering complexity of vehicle modernisation programmes. In the past, military clients have often over-specified vehicles and load beds, creating multiple small fl eets of varied specialist vehicles that could often not be used for any other purpose. Improvements in the capability and operational scope of load beds mean that military customers can order large numbers of similarly specified vehicles

Technology and systems development drive future vehicle modernisation programmes

AN MVE LOAD BED IN THE PROCESS OF

INSTALLATION TO THE VEHICLE CHASSIS.

Page 15: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

WWW.DEFENCEINDUSTRYREPORTS.COM | 13

AgilityQuality

IntegrityVehicle Integration

Vehicle Regeneration

Vehicle Configuration

Through Life Support

www.marshall-ls.com

Vehicle Engineering

A Marshall Land Systems Company

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 717921

[email protected]

able to undertake multiple tasks depending on the load bed fi tted.

Supply Chain and Management DevelopmentsFor the future, this will be a feature in the construction, maintenance and operation of military vehicles that need to carry load beds and, as a result, of the load beds themselves. The big developments may well be more in the operation of load beds and vehicles than purely in their engineering. Divisible loads will ensure that large fl eets of similar vehicles rather than multiple small fl eets of specialist vehicles can be used across the logistics supply chain. Furthermore, a division of the supply chain into ‘in theatre’ and ‘out of theatre’ segments along with the standardisation of load bed mounting systems will enable a rethink of military supply chain management into sectors that do require specialist military vehicles and load beds and sectors that don’t require specialised equipment.

This, in turn, will see the logistical supply fleets divided into a military specified fleet (with specialist load bed engineering to cope with ‘in theatre’ and battlefi eld conditions) and an off-the-shelf fl eet which can utilise ordinary commercial technology with all of the cost savings that will bring. Indeed, a further step is that this ‘out of theatre’ fl eet need not even be owned by the military and could be operated to standard commercial practices by non-military logistics specialists. While none of this is specific to load bed technology, all of it will have an impact on the manufacturers of load beds and the technological imperatives with which they have to work. It will also mean that military load bed

specifi cation will be even more uncompromisingly aimed at theatre of operations use.

John Reeve, Director and Consultant with Araldo Ltd., sums up this management conundrum very well in his article in the publication, ‘A Year of Innovation and Success’, from Iveco Defence Vehicles14;

“Recent additions to the operational capability portfolio will be competing with the mature support funding lines of existing core equipment… [with organisations] inextricably linked to equipment in the delivery of capability. Some of the drivers for organisational change, such as headcount reduction, relocation of headquarters, closure of depot facilities… and the [MoD] Defence Acquisition Change Program are delivering effect now” [so account needs to be taken of them].

A More Standardised FutureIncreasingly, load bed manufacturers will have to take into account that their equipment will be serviced and maintained in standard commercial facilities rather than in heavily manned specialist military maintenance capabilities and that wherever technology can simplify the operation and cost of maintenance, that will be a factor to be taken into account when military organisations buy equipment. Similarly, vehicle modernisation programmes will need to take into account that much of the specialist capability that was once built into vehicles can now be delivered by military load beds so that the vehicle fl eets can be far more standardised than was once the case. That, along with the modernisation of military supply chain management to modern commercial standards, will make the future outlook very interesting.

AN MVE LOAD BED AND CARGO SYSTEM CONFIGURED TO SUPPORT FIRE FIGHTING OPERATIONS.

Page 16: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

14 | WWW.DEFENCEINDUSTRYREPORTS.COM

The direction of

development has

been infl uenced by

the changing nature of

modern campaigns.

Load bed manufacturers

have had to fi nd ways

of providing capacity

to vehicles that would

previously have been

considered fi ghting units.

Meeting Current Needs Peter Dunwell, Staff Writer

The term ‘load bed’ suggests a structure mounted on a chassis-cab unit and fitted to carry containers or other items of freight. But these days there is a much wider definition of load bed refl ecting the much broader and less easily categorised nature of warfare. In that sense load beds are now being developed to adapt to a number of roles ranging from combat and combat support through service support and specialist operations such as fi re control and directing air strikes. Learning from AmateursIn one sense, the amateurs were ahead of the professionals in this, as the many heavily improvised Toyota pickup trucks seen in every guerrilla, insurgency and civil war situation testify. Having previously specifi ed and ordered specialist vehicles for many of the tasks that an army has to undertake, the professionals seem to have learned from the amateurs and now favour a fairly uniform fl eet of vehicles with a more adaptable fl eet of interchangeable load beds to achieve fl exibility and maximum utilisation of the resources available. A good example of this for a small vehicle similar to the Toyota pickup would be CAMELEON modular mission systems from OVIK Solutions Ltd.15 with which a number of ‘loads’ can be mounted on a standard chassis-cab.

Adapting to ChangeBut also, the direction of development has been infl uenced by the changing nature of modern campaigns. Load bed manufacturers have had to fi nd ways of providing capacity to vehicles that would previously have been considered fighting units, such as the British army’s Wolfhound16 whose operational envelope stretches from frontline combat operations right through to supply chain in theatres of war where the enemy has infi ltrated the whole area. Similarly, the Australian Army’s smaller Ocelot protected vehicle includes a utility variant with a load bed that can deliver palletised loads or loose loads in high threat areas such as Afghanistan. A similar load bed is available for the UK MoD’s variant on the same vehicle called the Foxhound17 produced by Ricardo plc18.

On the other side of the coin, what were previously regarded as supply and engineering vehicles now have to be heavily armoured themselves even though they are based on commercial chassis-cabs. A good example of this would be the UK MoD’s order for 260 Iveco vehicles for its ‘C’ vehicle fleet and based on the company’s largest commercial vehicles chassis, designed for heavy commercial applications such as quarry work, but with full off-road capability and carrying or towing load beds capable of delivering engineering functions like earthmoving plant, engineer construction plant and fi eld mechanical handling equipment used by the armed forces19. By combining its own engineering skills with those of specialist load bed builders, a commercial vehicle manufacturer is able to develop and quickly deliver a wide range of military vehicles.

Flexibility, Speed and StandardisationIn the current war fighting situation, forces have to specify and equip in real time to meet immediate threats prevalent in current war zones. So, when the Canadian Army ordered Mercedes-Benz Actros 8x8 heavy duty units in response to threats faced by its troops in Afghanistan, there was not the time available

And planning for all future possibilities in a world where change is always present

A UK MOD SUPPORT VEHICLE CONFIGURED WITH HINGED TAILGATE, DROP SIDES AND SUPER STRUCTURE.

Page 17: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

WWW.DEFENCEINDUSTRYREPORTS.COM | 15

AgilityQuality

IntegrityVehicle Integration

Vehicle Regeneration

Vehicle Configuration

Through Life Support

www.marshall-ls.com

Vehicle Engineering

A Marshall Land Systems Company

Marshall Vehicle Engineering Ltd

Hampstead Avenue,Mildenhall, Suffolk IP28 7RE

Tel: +44 (0) 1223 373221Fax: +44 (0) 1638 717921

[email protected]

for a programme running over years. The need was immediate and, because the vehicles and their load beds are largely built from Military Off-the-Shelf components, the units were able to be delivered directly to Canadian forces in Afghanistan within six months.

At the next level, for the UK MoD, MAN is delivering more than 7,000 vehicles to replace a fleet of general cargo vehicles including load beds to carry cargo, tanker variants, recovery versions and other functions. Speaking of this programme, Minister for Defence Equipment and Support in the previous UK Labour Government, RT. Hon. Baroness Ann Taylor said at the time the order was placed, “This milestone represents a significant achievement and is further evidence of how hugely successful the Support Vehicle programme is, delivering 7,285 new military vehicles under our £1.3bn procurement programme.”

Next GenerationThe next generation of military load beds will feature all of those advances in engineering that have changed every branch of the discipline. Because load beds are considered ‘parasitic’ parts of the transport solution, i.e.

not the chassis and not the load, it is the case that the less weight they impose on the chassis the more load can be carried. Numerous solutions are being explored including skeletal frameworks, although these may require additional mechanisms and engineering to carry pallets and loose loads. Also light materials, such as composites, can be used.

To increase the life expectancy of load beds they will need greater protection including better quality fixings and better protective coatings on more exposed surfaces.

To meet evolving and variable threats and requirements, a more flexible approach to vehicles and load beds is required for military users, who tend to keep their vehicles longer than commercial users. Vehicles like the Iveco Defence Vehicles LMV Protected Utility (PU) vehicle fi tted with a load bed able to carry to NATO pallets and aimed at evolving requirements for small high mobility and highly protected utility and logistics vehicles. There are also moves to develop lower cost training vehicles with controls and load beds the same as the operational vehicles but without the other battlefi eld accoutrements. There are even load platforms fitted on unmanned ground vehicles (UGVs) such as the multirole TRAKKER UGV, which can carry a 250kg payload while following its operator as he or she moves across the battlefi eld.

So, while the load bed system on modern military vehicles may not be the most glamorous part of the fi ghting force, given its ubiquity and the need to standardise vehicles while still performing multiple tasks, it is probably the most important in capability to conduct unpredictable and constantly changing warfare.

MVE’S ZINC PHOSPHATE AND E-DIP PLANT PROVIDES EXTENDED LIFE TO LOAD BEDS AND ASSOCIATED EQUIPMENTS.

AN MVE LOAD BED IN THE PROCESS

OF INSTALLATION TO THE VEHICLE CHASSIS.

Page 18: Special Report – Load Bed Systems for Modern Military Vehicles

SPECIAL REPORT: LOAD BED SYSTEMS FOR MODERN MILITARY VEHICLES

16 | WWW.DEFENCEINDUSTRYREPORTS.COM

References:1 ‘A Year of Innovation and Success’ www.iveco.com

2 Defense File http://www.defensefi le.com/Customisation/News/Military_Vehicles/Spare_Parts_Components_Repair_Maintenance_Tools/Tactical_Support_Vehicle_Gains_Loadbeds_From_Marshall.asp

3 British Army website http://www.army.mod.uk/equipment/engineering/1501.aspx

4 Wikipedia http://en.wikipedia.org/wiki/Palletized_Load_System 5 Armed Forces http://www.armedforces.co.uk/army/listings/l0146.html

6 Airforce Technology http://www.airforce-technology.com/projects/fl a/

7 autoblog http://www.autoblog.com/2008/06/24/mercedes-introduces-their-new-zetros-military-truck/

8 British Army http://www.army.mod.uk/equipment/engineering/1500.aspx

9 Army Technology http://www.army-technology.com/contractors/vehicles/iveco/

10 ‘A Year of Innovation and Success’ www.iveco.com

11 Marshall Land Systems http://www.marshallsv.com/Marshall_Vehicle_Engineering_Profi le.aspx

12 Hiab http://www.hiab.co.uk/Products/Loader-cranes/

13 ‘Mercedes Benz military vehicles where mobility meets protection’ http://www.mercedes-benz.co.za/content/south_africa/mpc/mpc_south_africa_website/en/home_mpc/truck_home/home/trucks/Military_Vehicles/News.html download ‘Mobility meets Protection’

14 ‘A Year of Innovation and Success’ www.iveco.com

15 OVIK Solutions Ltd. http://www.cameleon-mms.com/military/

16 Defense File http://www.defensefi le.com/Customisation/News/Military_Vehicles/Spare_Parts_Components_Repair_Maintenance_Tools/Tactical_Support_Vehicle_Gains_Loadbeds_From_Marshall.asp

17 Marshall Land Systems http://www.marshallsv.com/press-releases/Ocelot_Utility_Uses_MLS_Loadbed.aspx

18 Ricardo plc http://www.ricardo.com/en-GB/News--Media/Press-releases/News-releases1/2012/Ricardo-receives-sub-contract-for-Foxhound-production-from-General-Dynamics/

19 Army Recognition http://www.armyrecognition.com/italy_italian_defence_industry_company_uk/iveco_defence_vehicles_armoured_truck_army_military_vehicle_defense_company_industry_weapons_system.html

Page 19: Special Report – Load Bed Systems for Modern Military Vehicles

Defence Industry Reports… the leading specialist combined

online research and networking resource for senior military and defence industry professionals.

• Up to the minute Industry and Technology News and other content available to all site users on a free of charge, open access basis.

• Qualifi ed signed up members are able to access premium content Special Reports and interact with their peers using a variety of advanced online networking tools.

• Designed to help users identify new technical solutions, understand the implications of different technical choices and select the best solutions available.

• Thought Leadership – Advice and guidance from internationally recognised defence industry key opinion leaders.

• Peer Input – Contributions from senior military personnel and defence industry professionals.

• Independent Editorial Content – Expert and authoritative analysis from award winning journalists and leading industry commentators.

• Unbiased Supplier Provided Content.

• Designed to facilitate debate.

• Written to the highest professional standards.

 

Defence Industry Reports….the

leading specialist combined

online research and networking

resource for senior military and

defence industry professionals.

• Up to the minute Industry and Technology News and other content available to

all site users on a free of charge, open access basis.

• Qualified signed up members are able to access premium content Special

Reports and interact with their peers using a variety of advanced online

networking tools.

• Designed to help users identify new technical solutions, understand the

implications of different technical choices and select the best solutions

available.

• Thought Leadership - Advice and guidance from internationally recognised

defence industry key opinion leaders

• Peer Input - Contributions from senior military personnel and defence industry

professionals

• Independent Editorial Content - Expert and authoritative analysis from award

winning journalists and leading industry commentators

• Unbiased Supplier Provided Content

• Designed to facilitate debate

• Written to the highest professional standards

Visit: www.defenceindustryreports.com  

Page 20: Special Report – Load Bed Systems for Modern Military Vehicles