spooky2 contact mode instructions
TRANSCRIPT
Spooky2 Spooky2 Contact Mode Instructions
Our Users & Team
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
Here are detailed instructions on Spooky2 contact mode with Spooky Hand
Cylinders and Spooky Tens Pads.
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
Connection
Spooky Hand Cylinders
There are three different ways to connect Spooky Hand Cylinders depending
on whether you use Spooky Boost 2.0 or not, and they’ re both very simple.
First, connection via Spooky Boost 2.0:
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
A. Spooky Hand Cylinders with Spooky Boost 2.0
Connect the BNC-to-alligator clips cable that came with your generator to the
Colloidal Silver output of Spooky Boost 2.0. Then connect each alligator clip to
a cylinder as detailed below.
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
B. Spooky Hand Cylinders Direct Connect
Connect the BNC-to-alligator clips cable that came with your generator to Out 1
of the generator.
Then insert the alligator clips into the holes located at the plastic end of each
Spooky Hand Cylinder.The image below right shows the correct orientation for
your Spooky Hand Cylinders.
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
C. Without Boost 2.0 to Get Quadruple Power.
Connect both cables to Out 1 and Out 2. Now separate the red clips from the black ones - we won’t be connecting the black clips, so you can wrap each one in paper masking tape.
Now connect one red clip to a Spooky Tube electrode, and do the same for the other red clip - each red clip should be attached to an electrode.
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
Spooky Tens Pads
The connection of Spooky Tens Pads is the same as Spooky Hand
Cylinders (except that the adapter cable is Tens Cable).
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
Note:
1. Contact Mode needs higher amplitudes to achieve adequate body
penetration (14–20 volts).
2. Make sure the alligators have direct contact with the steel part of the tube
for good connection.
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
Contact Mode settings
There are JW-Killing ( Contact) and JW-Healing(Contact) presets in Spooky2
software.
They are applicable to both Hand Cylinders and Tens Pads.
Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com
Email:[email protected] [email protected]
Thank you!