sq40i (individual sequin device) check list sq40i (individual sequin device) sunstar precision...

SQ40i (Individual Sequin Device)

Check List

SQ40i (individual Sequin Device)

Sunstar Precision Sunstar Precision Co.,Ltd.Co.,Ltd.

SQ40i (Check Sheet)


YES NO

★ If you finish all Checks, click the right button to go back to install page.

SQ40i (Check Sheet)

Confirmation of parts

Check Point

Installation

Trouble-Shooting

Characters

Machine model confirmation· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

1. Write down SQ40i Model No. and S/N.

Model No. :

S/N :

Install date :

Technicain :

Note :

- 1 - Sunstar Precision Co.,Ltd.

SQ40i (Check Sheet)


YES NO

<NOTE>

<NOTE>


Check Point

Installation

Trouble-Shooting

Characters

Confirmation of parts · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

1. Are quantity and quality of SQ40i OK?

◆ L-Type : EA, R-Type : EA

2. Are quantity of the boards for SQ40i prepared properly?

◆ SQ B/D : EA, Control B/D : EA



SQ40i (Check Sheet)


YES NO

<NOTE>

★ If you finish all Checks, click the right button to check next check point.


3. Do you prepare all cables for SQ40i?

① Sub control board <-> SQ board connect

② SQ board power cable

③ Control board ↔ SQ board can communication cable

④ Encoder branch cable

⑤ Can communication branch cable

⑥ SQ board ↔ Air pressure Sol. power cable

⑦ Air pressure Error detection cable

⑧ SQ device connecting cable



Check Point

Installation

Trouble-Shooting

Characters

SQ40i (Check Sheet)


YES NO

<NOTE>

<NOTE>




Check Point

Installation

Trouble-Shooting

Characters


4. Do you prepare the parts of air pressure for SQ40i?

① Nipple(KQ2T06-04) and Nipple for branch (KQ2t06-00)

② Black and invisible tubes

③ Air pressure Sol.

④ Filter regulator and air pressure Sol. connecting hose

5. Do you prepare tools and jigs for installation?


YES NO

<NOTE>



Installation · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

1. Did you use water hose and level gauge when adjusting level?


Check Point

Installation

Trouble-Shooting

Characters

SQ40i Installation (Moving picture)


YES NO

<NOTE>


2. Do you confirm important check point of SQ40i(Assy)?

① Do you check state of bolt screwing and scratch and chopping?

② Is there no jamming of wheel bracket working?

③ Is there no jamming of driving lever pin working?

④ Is the cutting of spangles good?

⑤ Do you check lock-tight on the SQ base supply guide plate screws(M3 X L6)

⑥ Is there no jamming on lifting slide moving?

⑦ Is there no jamming when you screw ball screw by hands?

⑧ Is the state of motor cable connecting good?


Check Point

Installation

Trouble-Shooting

Characters

Installation · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·




YES NO

<NOTE>



3. Did you attach jumper pin(Ended resistor) on the control board and SQ board of the last head?

① Is a jumper(ended resistor) pin attached only on SQ board of the last head?

② Are the control board and SQ board proper with specification of machine?


Check Point

Installation

Trouble-Shooting

Characters

Installation · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·



YES NO

< 특이사항 >



4. Is cables of control B/D and SQ B/D connected properly?

① Is there no missing cables?

② Is there no bad/wrong connection?


Check Point

Installation

Trouble-Shooting

Characters

Installation · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·



YES NO

< 특이사항 >



5. Did you check in all check list of air pressure progress?

① Did you check nipple assembling and plug inserting to nipple of the first and last heads?

② Is the air pressure hose connected to nipple completely?

③ Did you check air pressure of Sol. and filter regulator with no missing?


Check Point

Installation

Trouble-Shooting

Characters

Installation · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·



YES NO

<NOTE>



6. Did you check in all the check list of attaching device and lifting damage absorbing?

① Is the needlebars and needles of SQ40i proper specification?

② Did you check level and close of SQ supply base and setting Jig?

③ Did you check close of front, side, under of Jig and SQ supply base?

④ Did you check damage absorbing of Lifting?


Check Point

Installation

Trouble-Shooting

Characters

Installation method · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·



YES NO

<NOTE>



7. Did you check in all check list of motor synchronization and quantity of SQ supping?

① Did you check lamp(ON) of potentiometer?

② Did you check close with Jig?

③ Is there no interval between supply lever and motor driving lever?

④ Did you check if SQ(spangle) cut is on the center?

⑤ Is there no jamming when Move Motor test?

⑥ Did you check returning to origin when origin function?


Check Point

Installation

Trouble-Shooting

Characters

Installation · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·



8-1. Did you check all check list of SQ40i?

① Was the guide attached as proper size?

② Does it matched SQ supply lever”B1” and standard pin hole of SQ base?

③ Is there no interval between SQ supply lever”B1”,”B2” and motor driving lever roller?

④ Is there no jamming when front, rear SQ supply and output, do front, rear SQ output in a line(straightly)?

⑤ When you pull spangles, are the spangles pulled?

⑥ Does the cut point of front, rear sequin correct?

⑦ Are there no jamming points when ball screw spins and lifting works?

YES NO

<NOTE>

★ If you finish all checks, click the right button to check mechanic check point.



Check Point

Installation

Trouble-Shooting

Characters





8-2. Did you check all check list of SQ40i?

① Do you have SQ Setting Jigs, use correctly when installation?

② Did you set device on the state of air suppied?

③ Did you check close of SQ suppy base with Jig, and level?

④ Did you keep distance 0.5mm ball screw between stopper screw?

⑤ Is there no contacting at needle and SQ cutting mes when needle down?

⑥ Is there no missing parts?

YES NO

<NOTE>



Check Point

Installation

Trouble-Shooting

Characters


★ If you finish all checks, click the right button to check electronic check point.



YES NO

<NOTE>



1. Did you check all check list of SQ40i?

① Are the control B/D and SQ B/D proper to install specification?

② Do you check attaching end resistor(jumper pin) and no other end resistors are on the board except the last head?


Check Point

Installation

Trouble-Shooting

Characters




9. Did you check in all check list of supply guide replacing process?

① Did you check setting state of replaced guide?

② Is there no jamming on supply lever working?

YES NO

<NOTE>




Check Point

Installation

Trouble-Shooting

Characters



SQ40i Setting · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

YES NO

<NOTE>




Check Point

Installation

Trouble-Shooting

Characters


8. Was SQ40i set properly to machine specification?

① L-Type R-Type Both-Type Extension

② What size(mm) of spangles?

L : Front mm, Rear mm / L : Front mm,

Rear mm ③ Does the OP.Box setting correct?


YES NO



Trouble - Shooting · · · · · · · · · · · · · · ·· · · · · · · · · · · · · · · · · · · · · · · · · · · · ·

1. Is there any strange symptom?

(When there is strange symptom, write down about the symptom in detail.)

<NOTE>


Check Point

Installation

Trouble-Shooting

Characters


sq40i (individual sequin device) check list sq40i (individual sequin device) sunstar precision...

Documents