Slide 1

Slide 2 Sta-Put w/ Strap Application/Use Slide 3 Remove the Sta-Put device from the side screen Lateral Restraint Application: STEP 1 Chock Release Handle (Red or Green) Step # 1: Step # 1: Holding the Chock Release Handle, pull upward to release the Sta-Put TM device from the side screen Universal Chock Hanger. Universal Chock Hanger Slide 4 Step # 2: Step # 2: Rotate the Sta-Put TM Face Plate(s) into the highest acceptable position. (Follow the vehicle manufacturer and AAR clearance guidelines.) Rotate the Sta-Put face plate(s) into position Rotate the Face Plate upward into position. High position: Both the Tall and Short face plates are upright. Medium position: The Tall face plate is collapsed and the Short face plate is upright. Low position: Both the Tall and Short face plates are collapsed. Application: STEP 2 Slide 5 Step # 3: Step # 3: One (1) device is placed on the outboard side of each wheel. Four(4) devices are required per vehicle as shown below (2 Red, 2 Green). Placement of the Sta-Put Devices (4 per vehicle) The black lateral restraints will rest against the inside wheel wall. The red or green release levers should face away from the vehicle. Application: STEP 3 Slide 6 Position the Sta-Put strap. Step # 4: Step # 4: Before positioning the Sta-Put against the wheel, ensure the strap does not obstruct the face plate. Application: STEP 4 Incorrect Correct = Strap does not obstruct the face plate. Move the strap away from the face plate before positioning against the wheel. Slide 7 Position the Sta-Put device against the wheel. Face Plate is seated as close to the wheel as possible. * AAR Guidelines allow up to space between the chock and the vehicle wheel. Lateral Restraint is seated as close to the wheel as possible. Application: STEP 5 Strap is correctly positioned. Step # 5: Step # 5: Ensure both Face Plate(s) and the Lateral Restraint are seated as close to the wheel as possible.* Slide 8 Use the Release Lever to engage the Locking Pin. #2 then push the Release Lever forward to engage the locking pin. Application: STEP 6 #1- Push Down or Step On the Articulating Block Step # 6: Step # 6: Push down or step on the black Articulating Block. Next, push the Release Lever toward the wheel to engage the locking pin. Slide 9 Position the Cleat Strap and Secure the J-Hook Strap to the Grate. Application: STEP 7 Step # 7: Step # 7: Position the Cleat Strap around the tire. Lengthen the strap as needed to affix the Flat J-Hook into the grating (approximately vertically down from the tire). PULL TAUGHT to secure. A) A) Position the strap around the tire surface. D) D) The strap should be roughly vertical to the tire. PULL TAUGHT to secure. B) B)Seat the Cleat Retention Lugs along the tread. C) Secure the Flat J-Hook to the Grating. Slide 10 Removal: #1) Removal: #1) Push the Release Lever away from the wheel to disengage #2) the Locking Pin. #2) Pull the chock away from the wheel (to release #3) the hooked teeth from the grating). #3) Lift upward to remove the chock. Release the Sta-Put from the grate. #1: Disengage the Locking Pin. #3: Remove the Sta-Put from the grating. Removal: #2 Pull the Sta-Put backward and up to release the hooked teeth from the grate. Slide 11 Slide 12 Secure the Sta-Put and Strap on the side screen Sta-Put Storage: Strap Hanger A) Secure the Sta-Put Device on the Universal Chock Hanger: Pull the Face Plate(s) upward, then fold to low (storage) position. Seat the first row of chock teeth into the metal rung nearest the deck. Engage the Release Lever to secure. B) Secure the Strap: B) Secure the Strap: With J-Hook facing the side screen securely wind the strap onto the hanger, ensuring it does not lie on the railcar deck. Universal Chock Hanger Storage: Storage: Store the device and strap on the corresponding hanger(s). Slide 13 For further information Contact: FCGCustomerService@Wabtec.com