What little girl doesn‘t dream of becoming a princess? With FIMO liquid, it‘s quick and easy to transform these lovely princess motifs into sturdy lantern shades. Print the motifs out on paper, cover with FIMO liquid, harden in the oven and then rub the paper off. The motifs are then transparent, dirt and water resistant and just the right size for the round cheese box lantern sets available from craft stores. Finish off by decorating with pretty ribbons, light the candle and watch the lantern shimmer and shine in a magical way.

You can find our products in well-stocked sales outlets. Should you have any queries, please call our hotline: +49 (0)911 9365-888.

Have fun crafting!

material

You will also require: Smooth work surface (glass or ceramic), lantern craft set: base and lid (cheese box), candle holder, handle, wooden lantern rod with wire hook (or, alternatively, electric lantern rod); colour or black-and-white print-outs of the two lantern motifs (inkjet or laser print-outs, each on A4 paper), coloured pencils for colouring in if required, large shallow bowl or sink, lantern film (opaque or clear, 50 x 23 cm), transparent double-sided sticky tape (approx. 3-5 mm wide), pin and kitchen roll, scissors, baking tray and baking paper, round nose pliers and wire cutter; for decorating: chiffon ribbon in light/bright pink, narrow satin ribbon in light and bright pink, kitchen knife, acrylic paint and brush or spray paint in light pink, candle

shopping / material list

Enchanting lantern for young princesses

Enchanting lantern for young princesses

You will need these STAEDTLER articles:

product colour art. no. quantity 3

For 1 lantern FIMO liquid -- 8050-00 BK 2

1

more creative tips at www.staedtler.com/creative_tips_for_FIMO

level of difficultyeasy medium hard

2

more creative tips at www.staedtler.com/creative_tips_for_FIMO

level of difficultyeasy medium hard

Print each of the lantern motifs out on white paper (A4). Each lantern motif print-out should be 25.5 cm wide and 20.5 cm high. Cut off any unprinted white paper around the edge. Important: The sheet of paper with the lantern motif should be flat. Place the page with the lantern motif on a sheet of baking paper. Next, cover the entire print-out with an even layer of FIMO liquid directly from the nozzle. Use a pin to prick any air bubbles open. Repeat the procedure for the second lantern motif.

1

Place both FIMO liquid motifs face-downwards on the work surface. Attach double-sided sticky tape to each of the motifs at the top and bottom edges and at the sides. Position the lantern motifs next to each other, slightly overlapping in the middle so that the motifs are stuck together. Position the lantern film exactly over the motifs and stick on. Now attach double-sided sticky tape to the lantern film at the top and bottom and at the sides.

2 3

Place the lantern motifs coated in FIMO liquid in the oven and harden for approx. 20 min at 130°C. Take them out and leave to cool. Place the FIMO liquid motif with the smooth (coated) surface face-downwards in a shallow bowl or sink. Add enough cold water to cover the motif and leave to soak for approx. 1 min. Then use your fingertip (not your fingernail!) to carefully rub the paper off. Put the FIMO liquid motif face-downwards on the work surface and use your fingers to pull the edges straight. Dab dry with kitchen roll and allow the motif to dry thoroughly.

Instructions for the enchanting lantern

Tip: Alternatively, you can print the motif out in black-and-white and colour it in using coloured pencils. All other steps are the same as for the coloured print-out version.

3

more creative tips at www.staedtler.com/creative_tips_for_FIMO

level of difficultyeasy medium hard

Paint or spray paint the lantern base, lid and rod in pink. Leave to dry. Then stick the lantern motifs around the outside of the base. Stand the lantern up and stick the sides of the motifs together.

4 5 6

Use double-sided sticky tape to stick the lid to the inside of the lantern. With a kitchen knife, cut two slits in the middle of the base and add the candle holder.

Use double-sided sticky tape to stick light and bright pink satin ribbon around the lantern base and along the sides of the motifs and chiffon ribbon around the top. Make two holes on opposite sides of the lid with the scissors, insert the handle and bend the ends of the wire using the round nose pliers. Finish off by adding two chiffon bows to the ends of the handles.

Instructions for the enchanting lantern

mor

e cr

eativ

e tip

s at

ww

w.s

taed

tler.c

om/c

reat

ive_

tips_

for_

FIM

O

mor

e cr

eativ

e tip

s at

ww

w.s

taed

tler.c

om/c

reat

ive_

tips_

for_

FIM

O

mor

e cr

eativ

e tip

s at

ww

w.s

taed

tler.c

om/c

reat

ive_

tips_

for_

FIM

O

mor

e cr

eativ

e tip

s at

ww

w.s

taed

tler.c

om/c

reat

ive_

tips_

for_

FIM

O