standard / double standard magnetic lock · standard installation door door glass frame em lock u...

INSTALLATION MANUAL

STANDARD / DOUBLE STANDARDMAGNETIC LOCK

Basic Installation Concept & Accessories

EM Lock

Glass

UBK Bracket For

Frame

GlassDoor

Glass Frame & Glass Door

Inswing

Door

Door

Frame

EM Lock

EM Bracket ForInswing Door With Cover

Inswing

LZ Bracket For Inswing Door

Door

Door

Frame

EM Lock

Inswing

Door

Door

EM Lock

Outswing

Frame

Standard Installation

Door

DoorGlass

Frame

EM Lock

U Bracket For Glass Door

Outswing

EM Lock

Door

L Bracket For Outswing Door

FrameDoor

Outswing

Cable Wire

Mounting Plate

Self-tappingScrew x10

Allen Wrench

Electromagnet x2

ArmaturePlate x2

Guide Pin x4

RubberWasher x2

ArmatureScrew x2

Cover PlateCover Screw x2

Anti ResidualMagnetismPart x2

Sexnut Bolt x2

Metal Washer x4

12/24 VDCPower

Anti-tamper Nut x4

Fixing Screw x4

250mA/24VDC500mA/12VDC

Holding Force

Voltage Input

Current Draw

Spec/Model

Cable Wire

Mounting Plate

Self-tappingScrew x5

12/24 VDCPower

Fixing Screw x2

Allen Wrench

Electromagnet

Armature Plate

Guide Pin x2

RubberWasher

ArmatureScrew

Cover Plate

CoverScrew

Anti ResidualMagnetismPart

Sexnut Bolt

Metal Washer x2

300lbs (136kg)

12/24VDC

GEM-300


600lbs (272kg)

12/24VDC

GEM-600


800lbs (363kg)

12/24VDC

GEM-800


1200lbs (545kg)

12/24VDC

GEM-1200

250mA/24VDC x2500mA/12VDC x2

600lbs (272kg)x2

12/24VDC

GEM-D600 GEM-D800 GEM-D1200

250mA/24VDC x2500mA/12VDC x2

800lbs (363kg)x2

12/24VDC

250mA/24VDC x2

500mA/12VDC x2

1200lbs (545kg)x2

12/24VDC

Single Door Double Door

For Outswing Door

INDOOR ELECTROMAGNETIC LOCK SERIES

Standard Installation

1

2

3

4

Template

Armature Plate

Allen wrench

9

Outswing

Power

12.7mm 8mm

Hollow Metal Door

6.8mm for M8-1.25 thread

Reinforced Door

12.7mm 8mm

Solid Door

36mm

5

Rubber Washer

6

77

8

OutdoorOutdoorOutdoor

Recommendation:

For Micro EM-locks (300 LBS), maximum thickness of door is 44 mm.

For Mini EM-locks (600 LBS), maximum thickness of door is 50 mm.

For Midi EM-locks (800 LBS), maximum thickness of door is 48 mm.

For Maxi EM-locks (1200 LBS), maximum thickness of door is 46 mm.

Fold the mounting template 90°

Place the template to the properposition of the door and frame. Mark the hole positions of the template on the door and frame.

Drill the holes according to themarks.

Fix the mounting plate on the door with mounting screws

Use the Allen wrench and fixingbolts to tighten the electromagneticlock to mounting plate

Connect the power and test theunit.

Fasten the mounting plate withthe mounting screws. The positionof the mounting plate should beadjustable.

The rubber washer makes thesurface of the armature plateadjustable in order to completelyfit the surface of magnetic lock.

Please install the armature plateas illustrated here. (Dimensions of the holes depend on the doortypes illustrated below.)

Drill a Ø8mm hole throughdoor on closing side.Enlargeto Ø12.7mm by a sexnutblot on the opening side. The depth is 36mm.

Drill a Ø6.8mm holeand tap on closing sidea M8x12.5 thread.

Drill a Ø8mm hole throughdoor, on closing side.Enlargeto Ø12.7mm by a sexnut bloton the opening side.

LZ bracket for Inswing doors

2

Use the fixing bolt to tighten theelectromagnetic lock on L bracket

1

Find a mounting location on thedoor frame for the L bracket. Makesure that the door is still closeable.

Close the door and connect thepower.

4

Insert the guide pins into thearmature plate.

3

5 6 7 Power

Outdoor

Finish

Outdoor

Power

Assemble the Z bracket, and makesure that the position of the Z bracketis adjustable.

Fasten the armature plate to the Zbracket (Must add rubber washer)

After the maglock attracts thearmature plate, adjust the Z bracket to fit the door.

Fasten the Z bracket to the door

H

Connecting Diagram

Models:

N.O.COM.N.C.

Mag Power Input

Sensor Input

Model:GEM-300M

Control Device N.C. contact or

LED indicatorGREEN: OpenRED : LockedNO LED: No power

Pow reI tupn

SPDT relay0.5A/125VAC

1A/24VDC

Sensor Input

Power Input

N.O.COM.N.C.

Access Relay

Bond sensor outputN.C. contact output: open statusN.O. contact output: locked status

Bond sensor output

N.C. contact output: open statusN.O. contact output: locked status

12 or 24VAutoswitchable


Control Device N.C. contact orAccess Relay


Bond sensor output

N.C. contact output: open statusN.O. contact output: locked status

LED indicatorGREEN: OpenRED: LockedNO LED: No power

Timer Adjustment

DEL neerG

DEL deR

SP

DT

rel

ay

Sensor in

sdnoces 08~10.5A

/125

VA

C1A

/24V

DC

tupnI rewoP

tupnI rosneS kcoL

.C.N MOC .O.N TSR TSR

JP Setting

(PCB back)

Models:GEM-800MDS-TD-LD, GEM-800MTD-LDGEM-1200MDS-TD-LD, GEM-1200MTD-LD

Relock time delay (Optional)Ensures the automatic lock modeworks after the door is closed properlyand it can be adjusted from 1 to 80

Models: TD series

Orange: N.O.White: ComBrown: N.C.

Door Status Sensor (optional)Door Status Sensor indicates thedoor is in an open or closed status.Models: DS seriesGreen LED (Default)

Red LED

seconds.



GEM-300, GEM-600, GEM-800, GEM-1200GEM-D600, GEM-D800, GEM-D1200

Problem Possible Cause Solution

Door does not lock No power

Poor contact between electromagnet and armature plate

Low voltage or incorrect voltage setting

A secondary diode was installed across the electromagnetic lock

Misalignment between the armature plateand electromagnetic lock

Make sure the wires are connected properly

Check that the power supply is connected and works properlyMake sure the lock switch is wired correctly (N.C.)

Make sure if the armature plate is deformed

Make sure the contact surfaces of the electromagnet and armature plate are clean and free from dust

Make sure the armature plate and electromagnetic lock are aligned correctly

Make sure if the rubber washer was used between magnet lock and armature plate

Ensure the electromagnet lock is set for the correct voltage.

Check for proper voltage at the electromagnetic locks input. If low, determine if the correct wire gauge is being used to prevent excessive voltage drop.

Remove any diode installed across the magnet for "spike" suppression. (The magnet is fitted with a metal oxide varistor to prevent back EMF)

Low holding force

Sensor output is not functioning

Trouble Shooting

N.O.COM.N.C. Mag Power Input

Sensor Input

Orange: N.O.White: ComBrown: N.C.

Timer Adjustment

1~80 seconds

LED indicatorGREEN: OpenRED : LockedNO LED: No power


Bond sensor outputN.C. contact output: open statusN.O. contact output: locked statusModels:

Door Status Sensor (optional)Door Status Sensor indicates the door is in an open or closed status.Models:

Buzzer Alarm (on the reverse)Door Held Open Alarm is an auditory feedback for users.Alarm sounds when the door is not closed for over a specifiedtime limit. VR timer (Timer Adjustment) is adjustable from1 to 80 seconds.


(Available for GEM-800MBZ & GEM-1200MBZ)

Relock time delay (Optional)Ensures the automatic lock mode works after the door isclosed properly and it can be adjusted from 1 to 80 seconds.

Connecting Diagram

GEM-600MDS, GEM-800MDS, GEM-1200MDSGEM-D600MDS, GEM-D800MDS, GEM-D1200MDS

GEM-600M, GEM-800M, GEM-1200MGEM-D600M, GEM-D800M, GEM-D1200M

GEM-600M, GEM-800M, GEM-1200MGEM-D600M, GEM-D800M, GEM-D1200M

GEM-D800MBZ & GEM-D1200MBZ)

The warranty period of Transmitter Solutions magnetic locks is twenty-four (24) months. This warranty shall begin on the date the keypad is manufactured. During the warranty period, the product will be repaired or replaced (at the sole discretion of Transmitter Solutions) if the product does not operate correctly due to a defective component. This warranty does not extend to (a) the case, which can be damaged by conditions outside the control of Transmitter Solutions, or (b) battery life. This warranty is further limited by the following disclaimer of warranty and liability:

EXCEPT AS SET FORTH ABOVE, TRANSMITTER SOLUTIONS MAKES NO WARRANTIES REGARDING THE GOODS, EXPRESS OR IMPLIED, INCLUDING WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. BUYER MAKES NO RELIANCE ON ANY REPRESENTATION OF TRANSMITTER SOLUTIONS, EXPRESS OR IMPLIED, WITH REGARD TO THE GOODS AND ACCEPTS THEM “AS-IS/WHERE-IS”. TRANSMITTER SOLUTIONS SELLS THE GOODS TO BUYER ON CONDITION THAT TRANSMITTER SOLUTIONS WILL HAVE NO LIABILITY OF ANY KIND AS A RESULT OF THE SALE. BUYER AGREES THAT TRANSMITTER SOLUTIONS SHALL HAVE NO LIABILITY FOR DAMAGES OF ANY KIND, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING INJURIES TO PERSONS OR PROPERTY, TO BUYER, ITS EMPLOYEES OR AGENTS, AS A RESULT OF THE SALE. BUYER ALSO AGREES TO HOLD TRANSMITTER SOLUTIONS HARMLESS FROM ANY CLAIMS BUYER, OR ANY THIRD PARTY, MAY HAVE AS A RESULT OF BUYER’S USE OR DISPOSAL OF THE GOODS. BUYER HAS READ THIS DISCLAIMER AND AGREES WITH ITS TERMS IN CONSIDERATION OF RECEIVING THE GOODS.

WARRANTY:

H

standard / double standard magnetic lock · standard installation door door glass frame em lock u...

Documents