start mercedes solution - installer.com · 2012+ mercedes benz ml class 2013+ mercedes benz gl...

10
1 © 2012 Directed. All rights reserved. DIGITAL REMOTE START SYSTEM WWW.XPRESSKIT.COM MADE IN THE USA XPRESSSTART Mercedes Solution Installation Instructions 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a direct plug in interface to the rear of the Mercedes Benz key cylinder. Please read this manual in it’s entirety prior to installation as there is a specific order of operation that needs to be followed. Tools and Parts you will need: T-20 driver Drill 3/4” drill bit or Unibit XPRESSSTART Wiring Overview W/X166 EIS (KEY CYLINDER) EIS (KEY CYLINDER) XPRESSSTART VALET SWITCH AFTER INSTALLATION BEFORE INSTALLATION GREEN PLUG BLUE PLUG GREEN PLUG WHITE PLUG SUPPLIED T-HARNESS ML & GL Installation 1. Remove (3) T-20 screws from the driver’s under dash panel. 2. Lower dash panel down and move air vent out of the clips that hold it in place. 3. Reach up to the rear of the EIS. There are two retaining clips on the top and bottom of the EIS. 4. Grasp the wiring harness while squeezing the retaining clips together to remove the EIS. 5. Pull the EIS with harness attached out of the dash to access the wiring. 6. Unplug both plugs (blue and green) from the EIS. QRNMB166 2012-12

Upload: others

Post on 01-Oct-2020

66 views

Category:

Documents


12 download

TRANSCRIPT

Page 1: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

1© 2012 Directed. All rights reserved.

DIGITAL RemoTe sTART sysTem

www.xpResskIT.com mADe IN THe UsA

XPRESSSTART Mercedes Solution

Installation Instructions

2012+ Mercedes Benz ML Class2013+ Mercedes Benz GL Class

2013 Mercedes Benz G Class

The XPRESSSTART Mercedes Solution is designed as a direct plug in interface to the rear of the Mercedes Benz key cylinder. Please read this manual in it’s entirety prior to installation as there is a specific order of operation that needs to be followed.

Tools and Parts you will need:• T-20 driver• Drill• 3/4” drill bit or Unibit

XPRESSSTART Wiring OverviewW/X166

REMOVE WHITE SHELLAND REPLACE WITH

PROVIDED BLUE SHELL

WHITE 10 PIN PLUG(BLACK INSERT WITHWHITE OUTER SHELL)

EIS(KEY CYLINDER)

EIS(KEY CYLINDER)

EIS(KEY CYLINDER)

EIS(KEY CYLINDER)

EIS(KEY CYLINDER)

EIS(KEY CYLINDER)

FIT ORIGINAL WHITESHELL TO THE

PROVIDED T-HARNESS

FACTORY HARNESS WITHBLUE SHELL FITTED

XPRESSSTART

XPRESSSTART

XPRESSSTART

VALET SWITCH

SUPPLIED T-HARNESS

AFTER INSTALLATION

BEFORE INSTALLATION

VALET SWITCH

BLACK PLUG

WHITE PLUG

AFTER INSTALLATION

BEFORE INSTALLATION

VALET SWITCH

AFTER INSTALLATION

BEFORE INSTALLATION

BLACK PLUG

WHITE PLUG

GREEN PLUG

BLUE PLUG

GREEN PLUG

WHITE PLUG

SUPPLIED T-HARNESS

SUPPLIED T-HARNESS

ML & GL Installation

1. Remove (3) T-20 screws from the driver’s under dash panel.2. Lower dash panel down and move air vent out of the clips that hold it in place.3. Reach up to the rear of the EIS. There are two retaining clips on the top and bottom of the EIS.4. Grasp the wiring harness while squeezing the retaining clips together to remove the EIS.5. Pull the EIS with harness attached out of the dash to access the wiring.6. Unplug both plugs (blue and green) from the EIS.

QRNMB166 2012-12

Page 2: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

2 © 2012 Directed. All rights reserved.

7. Remove the blue housing from the harness and install it on to the supplied XPRESSSTART T-harness.8. Install the supplied white housing on to the empty plug where the blue housing originally was.9. Plug the T-harness into the factory wiring and the EIS.10. Once ALL connections are secured, turn on the valet switch and verify the LEDs visible inside the XPRESSSTART are flashing.11. Start the vehicle with the key or with the push button to verify your work. If the vehicle starts and runs, you’ve made all the

connections correctly.12. Shut the vehicle off.13. Push the panic button once on the remote to test the XPRESSSTART.14. Once you are satisfied with its operation, shut down the XPRESSSTART by pushing the panic button once.15. Locate a place to secure the XPRESSSTART module in the dash cavity away from any heat sources.16. Secure the module in its final location.17. Locate a place for the valet override switch. Recommended location is the driver’s under dash panel.18. Drill a 3/4” hole in the desired location.19. Route the wires for the valet switch through hole made in step 18.20. Plug in the valet switch to the XPRESSSTART valet switch leads. Make sure the spade connectors are fully installed on the

switch.21. Line up the vent to the under dash panel in the clips that hold it into place.22. Reinstall the under dash panel making sure the vent is lined up to the duct in the dash.23. Reinstall (3) T-20 screws to hold the panel in place.24. If vehicle is equipped with KeylessGo, see additional required connection on page 4 to retain KeylessGo features.

Installation

1. Remove (3) T-20 screws from the driver’s under dash panel.2. Lower dash panel down and move air vent out of the clips that hold it in place.3. Reach up to the rear of the EIS. There are two retaining clips on the top and bottom of the EIS.4. Grasp the wiring harness while squeezing the retaining clips together to remove the EIS.5. Pull the EIS with harness attached out of the dash to access the wiring.6. Unplug both plugs (blue and green) from the EIS.7. Remove the blue housing from the harness and install it on to the supplied Smartkey Starter® T-

harness.8. Install the supplied white housing on to the empty plug where the blue housing originally was.9. Plug the T-harness into the factory wiring and the EIS.10.Once ALL connections are secured, turn on the valet switch and verify the LEDs visible inside the

XPRESSSTART are flashing.11.Start the vehicle with the key or with the push button to verify your work. If the vehicle starts and

runs, you’ve made all the connections correctly.12.Shut the vehicle off.13.Push the panic button once on the remote to test the XPRESSSTART.14.Once you are satisfied with its operation, shut down the XPRESSSTART by pushing the panic

button once.15.Locate a place to secure the XPRESSSTART module in the dash cavity away from any heat

sources.16.Secure the module in its final location.17.Locate a place for the valet override switch. Recommended location is the driver’s under dash

panel.18.Drill a 3/4” hole in the desired location.19.Route the wires for the valet switch through hole made in step 18.20.Plug in the valet switch to the XPRESSSTART valet switch leads. Make sure the spade

connectors are fully installed on the switch.21. Line up the vent to the under dash panel in the clips that hold it into place.22.Reinstall the under dash panel making sure the vent is lined up to the duct in the dash.23.Reinstall (3) T-20 screws to hold the panel in place

Remove (3) T-20 Lower panel and move vent

Installation

1. Remove (3) T-20 screws from the driver’s under dash panel.2. Lower dash panel down and move air vent out of the clips that hold it in place.3. Reach up to the rear of the EIS. There are two retaining clips on the top and bottom of the EIS.4. Grasp the wiring harness while squeezing the retaining clips together to remove the EIS.5. Pull the EIS with harness attached out of the dash to access the wiring.6. Unplug both plugs (blue and green) from the EIS.7. Remove the blue housing from the harness and install it on to the supplied Smartkey Starter® T-

harness.8. Install the supplied white housing on to the empty plug where the blue housing originally was.9. Plug the T-harness into the factory wiring and the EIS.10.Once ALL connections are secured, turn on the valet switch and verify the LEDs visible inside the

XPRESSSTART are flashing.11.Start the vehicle with the key or with the push button to verify your work. If the vehicle starts and

runs, you’ve made all the connections correctly.12.Shut the vehicle off.13.Push the panic button once on the remote to test the XPRESSSTART.14.Once you are satisfied with its operation, shut down the XPRESSSTART by pushing the panic

button once.15.Locate a place to secure the XPRESSSTART module in the dash cavity away from any heat

sources.16.Secure the module in its final location.17.Locate a place for the valet override switch. Recommended location is the driver’s under dash

panel.18.Drill a 3/4” hole in the desired location.19.Route the wires for the valet switch through hole made in step 18.20.Plug in the valet switch to the XPRESSSTART valet switch leads. Make sure the spade

connectors are fully installed on the switch.21. Line up the vent to the under dash panel in the clips that hold it into place.22.Reinstall the under dash panel making sure the vent is lined up to the duct in the dash.23.Reinstall (3) T-20 screws to hold the panel in place

Remove (3) T-20 Lower panel and move vent

Remove (3) T-20 Lower panel and move vent

EIS removed T-harness installed

EIS removed T-harness installed

EIS removed T-harness installed

Page 3: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

3© 2012 Directed. All rights reserved.

G Wagon Installation

1. Lower the steering column and extend it to its maximum.2. Grasp the plastic trim below the instrument cluster and pull toward you.3. Continue removing the boot around the steering column and pull it away from the dash as far as itwill go.4. Reach in the behind the EIS and unplug the two plugs, (1) green plug and (1) blue plug, and unplug them.5. Connect the XPRESSSTART harness in line with the plugs and connect the opposite end into the rear of the EIS.6. Remove the under dash panels using a T-20 driver.7. Route the XPRESSSTART harness to a location where the starter can be mounted away from heat and moving parts.8. Connect the XPRESSSTART to the T-harness and securely mount it.9. Drill a 3/4” hole for the valet switch in an easily accessible location under the dash.10. Remove the valet switch from the T-harness and mount it in the hole just drilled and reconnect the wires.11. Start the vehicle with the key and let it run for 60 seconds then turn it off.12. Press the panic button on the keyfob once and test the remote start.13. Reassemble the under dash.14. Reinstall the steering wheel boot.

Installation

1. Lower the steering column and extend it to its maximum.2. Grasp the plastic trim below the instrument cluster and pull toward you.3. Continue removing the boot around the steering column and pull it away from the dash as far as it

will go.4. Reach in the behind the EIS and unplug the two plugs, (1) green plug and (1) blue plug, and

unplug them.5. Connect the Smartkey Starter® harness in line with the plugs and connect the opposite end into

the rear of the EIS.6. Remove the under dash panels using a T-20 driver.7. Route the Smartkey Starter® harness to a location where the starter can be mounted away from

heat and moving parts.8. Connect the Smartkey Starter® to the T-harness and securely mount it.9. Drill a 3/4” hole for the valet switch in an easily accessible location under the dash.10.Remove the valet switch from the T-harness and mount it in the hole just drilled and reconnect the

wires.11.Start the vehicle with the key and let it run for 60 seconds then turn it off.12.Press the panic button on the keyfob once and test the remote start.13.Reassemble the under dash.14.Reinstall the steering wheel boot.

Remove steering wheel boot EIS plug location at rear of EIS

Copyright 2012 Midcity Engineering®

EIS plugs

Installation

1. Lower the steering column and extend it to its maximum.2. Grasp the plastic trim below the instrument cluster and pull toward you.3. Continue removing the boot around the steering column and pull it away from the dash as far as it

will go.4. Reach in the behind the EIS and unplug the two plugs, (1) green plug and (1) blue plug, and

unplug them.5. Connect the Smartkey Starter® harness in line with the plugs and connect the opposite end into

the rear of the EIS.6. Remove the under dash panels using a T-20 driver.7. Route the Smartkey Starter® harness to a location where the starter can be mounted away from

heat and moving parts.8. Connect the Smartkey Starter® to the T-harness and securely mount it.9. Drill a 3/4” hole for the valet switch in an easily accessible location under the dash.10.Remove the valet switch from the T-harness and mount it in the hole just drilled and reconnect the

wires.11.Start the vehicle with the key and let it run for 60 seconds then turn it off.12.Press the panic button on the keyfob once and test the remote start.13.Reassemble the under dash.14.Reinstall the steering wheel boot.

Remove steering wheel boot EIS plug location at rear of EIS

Copyright 2012 Midcity Engineering®

EIS plugs

Remove steering wheel boot EIS plug location at rear of EIS

Page 4: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

4 © 2012 Directed. All rights reserved.

2012+ ML, 2013+ GL W/X166 KeylessGo Connection

The KeylessGo connection for the 2012 ML is quite involved and requires significant disassembly of the rear of the vehicle. This guide assumes the basic XPRESSSTART Mercedes Solution is installed and functioning properly.

Tools and Parts you will need:• E14 Torx Socket - ML only• T30 Torx Driver - GL only• T45 Torx Bit• T40 Torx Bit• Panel Removal Tool• Pick tool• KG20 Harness

ML Installation

1. Remove the driver’s rear door sill plate.2. Fold the driver’s rear seat bottom forward.3. Remove (2) bolts holding the seat bottom to the floor.4. Remove the driver’s side rear seat bottom from the vehicle.5. Remove (1) bolt holding the center seat back bracket and (1) bolt holding the seat belt.6. Fold the rear driver’s side seat back down.7. Pry up the covers for the tie down loops in the cargo area.8. Remove the bolts from each tie down and remove the hooks from their mounts.9. Remove the cargo cover.10. Remove the foam inserts directly behind the rear seats.11. Remove (2) additional bolts that hold the driver’s side rear seat back.12. Unclip the wire harness that is clipped to the driver’s side rear seat bracket.13. Flip the driver’s side rear seat back into the cargo area making sure the wire harness doesn’t get pinched or pulled beyond its

limit.14. Pull up the carpet to access the KeylessGo module on the floor.15. Route the supplied KeylessGo harness from the XPRESSSTART module to the rear seat area.16. Unplug the main connector from the KeylessGo module.17. Remove the shroud from the main KeylessGo connector.18. Remove the brown and brown/red wires from the KeylessGo plug. Make a note of the wire locations in the plug.19. Insulate the ends of the removed wires.20. Using the supplied W166 KG adapter, populate the brown and brown/red wires into the locations where the factory wires

were removed.21. Reinstall the shroud for the KeylessGo main plug and plug it back in.22. Close all doors, hood and hatch to test the remote start.23. Remote start the vehicle. If everything is connected properly, you should be able to lock and unlock the vehicle using the touch

sensors on the door handles while the remote start is running.24. Unlock and enter the vehicle. Push the start button one time. The lights should flash three times to confirm key take over.25. Turn off the vehicle.26. Secure the KG20 harness to existing wiring.27. Lay the carpet back in place.28. Remount the seat back and seat belt. Make sure the wire harness is clipped back into place.29. Fold the seat back down and install the foam inserts and the cargo cover.30. Reinstall the cargo tie down hooks.31. Fold the seat back up.32. Reinstall the seat bottom and bolt it in place.33. Reinstall the sill plate.

Page 5: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

5© 2012 Directed. All rights reserved.

21.Reinstall the shroud for the KeylessGo main plug and plug it back in.22.Close all doors, hood and hatch to test the remote start.23.Remote start the vehicle. If everything is connected properly, you should be able to lock and unlock the

vehicle using the touch sensors on the door handles while the remote start is running. 24.Unlock and enter the vehicle. Push the start button one time. The lights should ßash three times to conÞrm

key take over.25.Turn off the vehicle.26.Secure the KG20 harness to existing wiring.27.Lay the carpet back in place.28.Remount the seat back and seat belt. Make sure the wire harness is clipped back into place.29.Fold the seat back down and install the foam inserts and the cargo cover.30.Reinstall the cargo tie down hooks.31.Fold the seat back up.32.Reinstall the seat bottom and bolt it in place.33.Reinstall the sill plate.

Remove sill plate" " " " " " Unbolt seat bottom

Seat bottom removed"" " " " " Unbolt seat back

21.Reinstall the shroud for the KeylessGo main plug and plug it back in.22.Close all doors, hood and hatch to test the remote start.23.Remote start the vehicle. If everything is connected properly, you should be able to lock and unlock the

vehicle using the touch sensors on the door handles while the remote start is running. 24.Unlock and enter the vehicle. Push the start button one time. The lights should ßash three times to conÞrm

key take over.25.Turn off the vehicle.26.Secure the KG20 harness to existing wiring.27.Lay the carpet back in place.28.Remount the seat back and seat belt. Make sure the wire harness is clipped back into place.29.Fold the seat back down and install the foam inserts and the cargo cover.30.Reinstall the cargo tie down hooks.31.Fold the seat back up.32.Reinstall the seat bottom and bolt it in place.33.Reinstall the sill plate.

Remove sill plate" " " " " " Unbolt seat bottom

Seat bottom removed"" " " " " Unbolt seat back

Remove sill plate Unbolt seat bottom

21.Reinstall the shroud for the KeylessGo main plug and plug it back in.22.Close all doors, hood and hatch to test the remote start.23.Remote start the vehicle. If everything is connected properly, you should be able to lock and unlock the

vehicle using the touch sensors on the door handles while the remote start is running. 24.Unlock and enter the vehicle. Push the start button one time. The lights should ßash three times to conÞrm

key take over.25.Turn off the vehicle.26.Secure the KG20 harness to existing wiring.27.Lay the carpet back in place.28.Remount the seat back and seat belt. Make sure the wire harness is clipped back into place.29.Fold the seat back down and install the foam inserts and the cargo cover.30.Reinstall the cargo tie down hooks.31.Fold the seat back up.32.Reinstall the seat bottom and bolt it in place.33.Reinstall the sill plate.

Remove sill plate" " " " " " Unbolt seat bottom

Seat bottom removed"" " " " " Unbolt seat back

21.Reinstall the shroud for the KeylessGo main plug and plug it back in.22.Close all doors, hood and hatch to test the remote start.23.Remote start the vehicle. If everything is connected properly, you should be able to lock and unlock the

vehicle using the touch sensors on the door handles while the remote start is running. 24.Unlock and enter the vehicle. Push the start button one time. The lights should ßash three times to conÞrm

key take over.25.Turn off the vehicle.26.Secure the KG20 harness to existing wiring.27.Lay the carpet back in place.28.Remount the seat back and seat belt. Make sure the wire harness is clipped back into place.29.Fold the seat back down and install the foam inserts and the cargo cover.30.Reinstall the cargo tie down hooks.31.Fold the seat back up.32.Reinstall the seat bottom and bolt it in place.33.Reinstall the sill plate.

Remove sill plate" " " " " " Unbolt seat bottom

Seat bottom removed"" " " " " Unbolt seat backSeat bottom removed Unbolt seat back

Unbolt cargo tie downs" " " " " Remove cargo cover

Remove foam inserts" " " " " " Unbolt seat bracket

Unclip wire harness" " " " " " Flip seat back into cargo area

Unbolt cargo tie downs" " " " " Remove cargo cover

Remove foam inserts" " " " " " Unbolt seat bracket

Unclip wire harness" " " " " " Flip seat back into cargo area

Unbolt cargo tie downs Remove cargo cover

Page 6: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

6 © 2012 Directed. All rights reserved.

Unbolt cargo tie downs" " " " " Remove cargo cover

Remove foam inserts" " " " " " Unbolt seat bracket

Unclip wire harness" " " " " " Flip seat back into cargo area

Unbolt cargo tie downs" " " " " Remove cargo cover

Remove foam inserts" " " " " " Unbolt seat bracket

Unclip wire harness" " " " " " Flip seat back into cargo area

Remove foam inserts Unbolt seat bracket

Unbolt cargo tie downs" " " " " Remove cargo cover

Remove foam inserts" " " " " " Unbolt seat bracket

Unclip wire harness" " " " " " Flip seat back into cargo area

Unbolt cargo tie downs" " " " " Remove cargo cover

Remove foam inserts" " " " " " Unbolt seat bracket

Unclip wire harness" " " " " " Flip seat back into cargo area

Unclip wire harness Flip seat back into cargo area

Pull up carpet" " " " " " " Unplug KeylessGo module

" " " " " " " " New pins installed, reinstall shroud

Shroud removed from plug

" " " " " " " " Plug KeylessGo module in

Pull up carpet" " " " " " " Unplug KeylessGo module

" " " " " " " " New pins installed, reinstall shroud

Shroud removed from plug

" " " " " " " " Plug KeylessGo module in

Pull up carpet Unplug KeylessGo module

Page 7: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

7© 2012 Directed. All rights reserved.

Pull up carpet" " " " " " " Unplug KeylessGo module

" " " " " " " " New pins installed, reinstall shroud

Shroud removed from plug

" " " " " " " " Plug KeylessGo module in

Shroud removed from plug Pull up carpet" " " " " " " Unplug KeylessGo module

" " " " " " " " New pins installed, reinstall shroud

Shroud removed from plug

" " " " " " " " Plug KeylessGo module in

Pull up carpet" " " " " " " Unplug KeylessGo module

" " " " " " " " New pins installed, reinstall shroud

Shroud removed from plug

" " " " " " " " Plug KeylessGo module inNew pins installed, reinstall shroud Plug KeylessGo module in

Page 8: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

8 © 2012 Directed. All rights reserved.

GL Installation

1. Remove driver’s rear door sill.2. Fold driver’s middle row seat all the way forward.3. Remove torx bolt holding seat belt to rear side panel.4. Pull back weather strip on the back side of the rear door opening.5. Remove (1) T-30 torx from inside the rear retractible cover mount.6. Pop side panel partially out.7. Route the 166 KG adapter to the rear side panel area.8. Reach in and unplug connector on KG module (see picture).9. Remove the shroud from that connector10. Remove the brown and brown/red pins from the black connector making a note of their position11. Install the pins from the 166 KG adapter into the spots where the factory wires were removed.12. Reinstall the shroud for that plug.13. Reinstall the plug into the module.14. Pop the side panel back into place.15. Reinstall (1) T-30 Torx and cosmetic cover.16. Reinstall Torx bolt for seat belt.17. Reinstall driver’s rear door sill panel.

Installation - GL

1. Remove driver’s rear door sill.2. Fold driver’s middle row seat all the way forward.3. Remove torx bolt holding seat belt to rear side panel.4. Pull back weather strip on the back side of the rear door opening.5. Remove (1) T-30 torx from inside the rear retractible cover mount.6. Pop side panel partially out.7. Route the 166 KG adapter to the rear side panel area.8. Reach in and unplug connector on KG module (see picture).9. Remove the shroud from that connector10.Remove the brown and brown/red pins from the black connector making a note of their position11.Install the pins from the 166 KG adapter into the spots where the factory wires were removed.12.Reinstall the shroud for that plug.13.Reinstall the plug into the module.14.Pop the side panel back into place.15.Reinstall (1) T-30 Torx and cosmetic cover.16.Reinstall Torx bolt for seat belt.17.Reinstall driver’s rear door sill panel.

Remove door sill" " " " " " Remove seat belt

Installation - GL

1. Remove driver’s rear door sill.2. Fold driver’s middle row seat all the way forward.3. Remove torx bolt holding seat belt to rear side panel.4. Pull back weather strip on the back side of the rear door opening.5. Remove (1) T-30 torx from inside the rear retractible cover mount.6. Pop side panel partially out.7. Route the 166 KG adapter to the rear side panel area.8. Reach in and unplug connector on KG module (see picture).9. Remove the shroud from that connector10.Remove the brown and brown/red pins from the black connector making a note of their position11.Install the pins from the 166 KG adapter into the spots where the factory wires were removed.12.Reinstall the shroud for that plug.13.Reinstall the plug into the module.14.Pop the side panel back into place.15.Reinstall (1) T-30 Torx and cosmetic cover.16.Reinstall Torx bolt for seat belt.17.Reinstall driver’s rear door sill panel.

Remove door sill" " " " " " Remove seat beltRemove door sill Remove seat belt

Remove screw cover" " " " " " Remove T-30

Pull back weather strip " " " " " Pop out side panel

remove white plug" " " " " " plug removed

KG module under bracket

remove white plug

Remove screw cover" " " " " " Remove T-30

Pull back weather strip " " " " " Pop out side panel

remove white plug" " " " " " plug removed

KG module under bracket

remove white plug

Remove screw cover Remove T-30

Page 9: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

9© 2012 Directed. All rights reserved.

Remove screw cover" " " " " " Remove T-30

Pull back weather strip " " " " " Pop out side panel

remove white plug" " " " " " plug removed

KG module under bracket

remove white plug

Remove screw cover" " " " " " Remove T-30

Pull back weather strip " " " " " Pop out side panel

remove white plug" " " " " " plug removed

KG module under bracket

remove white plugPull back weather strip Pop out side panel

Remove screw cover" " " " " " Remove T-30

Pull back weather strip " " " " " Pop out side panel

remove white plug" " " " " " plug removed

KG module under bracket

remove white plug

Remove screw cover" " " " " " Remove T-30

Pull back weather strip " " " " " Pop out side panel

remove white plug" " " " " " plug removed

KG module under bracket

remove white plug

Remove white plug Plug removed

Shroud removed" " " " " " KG harness properly installed into plug

Shroud removed" " " " " " KG harness properly installed into plugShroud removed KG harness properly installed into plug

Page 10: START Mercedes Solution - installer.com · 2012+ Mercedes Benz ML Class 2013+ Mercedes Benz GL Class 2013 Mercedes Benz G Class The XPRESSSTART Mercedes Solution is designed as a

10 © 2012 Directed. All rights reserved.

Accessory Connection Instructions

Each XPRESSSTART is equipped with a (4) pin and a (3) pin connector at the end.

The (4) pin connector is designed to accept a D2D cable from an XL202 RF translator module to provide the ability for adding long range remotes and 2 way capability to the XPRESSSTART. There is no programming required for the module. The remotes need to be programmed to the XL202 which should have instructions provided with it.

The (3) pin connector is designed to accept the ESP cable that comes with the Directed SmartStart module (DSM100, DSM200 or DSM250). The cable can be plugged directly in to the port. The power and ground must be connected (soldered and taped) to the XPRESSSTART harness. Please see the below diagram. DO NOT USE THE 4 PIN PLUG ON A SMARTSTART MODULE.

SKS On Board KeylessGo Finder Instructions

There is an on board KeylessGo Þnder. This will make Þnding the correct plug for connecting to the KeylessGo system on vehicles that require it much easier. The basic install of the XPRESSSTART needs to be completed prior to testing for KeylessGo (this guide assumes the xpressSTART module is installed and properly working).

Instructions

1. Locate the speciÞed CAN distribution block where the KeylessGo connection should be made.2. Turn the key to accessory (one click clockwise from the off position). If there is a push button in the ignition cylinder, it can be

removed so the key can be inserted in its place. Grasp the button and pull it out of the ignition switch.3. Look inside the XPRESSSTART module through the end plate opposite the main wiring plug. You should see red LEDs that

are lit up. One of those should be flashing at a slow pace. 4. In the CAN distribution block, begin to remove connectors one at a time. Each connector should be unplugged for 15-20

seconds each. Observe the flashing light as you do this. You should end up with two connectors that cause the flashing light to stop flashing and stay solid on or solid off.

5. Isolate those two connectors to one end of the distribution block and leave the rest alone.6. Turn the key to the off position and remove it.7. Take the two connectors from step 5 and remove one at a time. Once one is removed, use the keyfob to unlock the doors.

Removing one of those connectors will cause the door locks to stop working from the keyfob and one won’t. 8. Take the connector that caused the door locks to stop working and plug it back in.9. Connect the KeylessGo harness to the plug from step 7 where the door locks continued to work.

DEI Connection Instructions

Each XPRESSSTART is equipped with a (4) pin and a (3) pin connector at the end.

The (4) pin connector is designed to accept a D2D cable from an XL202 RF translator module to provide the ability for adding long range remotes and 2 way capability to the XPRESSSTART. There is no programming required for the module. The remotes need to be programmed to the XL202 which should have instructions provided with it.

The (3) pin connector is designed to accept the ESP cable that comes with the Directed SmartStart module (DSM100, DSM200 or DSM250). The cable can be plugged directly in to the port. The power and ground must be connected (soldered and taped) to the XPRESSSTART harness. Please see the below diagram. DO NOT USE THE 4 PIN PLUG ON A SMARTSTART MODULE.

SmartStart powertop row, Þrst pin,

red

SmartStart groundbottom row, Þrst

pin, brown

Troubleshooting Diagnostic Flashes

While running on remote start, any of the following will cause vehicle shut down.

• opening the hood (7 flashes)• depressing the brake pedal (6 flashes)• increasing the RPM over normal idle (8 flashes)• three failed starts/low RPM (9 flashes)• communications error (10 flashes)

The vehicle will be limited to (5) remote starts between normal keyed operation.

If the lights flash (5) times the starter is out of sync with the vehicle. This is a rare occurrence. Should it happen, you must start thevehicle with the key or the KeylessGo button for at least one minute to synchronize.