starter, sinamics g120 faq y january 2014 - siemens · siemens industry online support answers for...
TRANSCRIPT
Siemens Industry Online Support
Answers for industry.
STARTER: USB connection withSINAMICS G120
STARTER, SINAMICS G120
FAQ January 2014
Table of contents
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 2/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Table of contents1 Preconditions for an online connection between STARTER and
SINAMICS G120 via USB ................................................................................... 3
2 What do I do if …? ............................................................................................. 4
A. after installing/updating STARTER, I cannot establish anonline connection via USB? .................................................. 4
B. after "withdrawing" and "inserting" the USB cable, a USBconnection can no longer be established? ........................... 6
C. after installing/updating STARTER, I cannot establish anonline connection via USB, however the registry entries areOK? ....................................................................................... 8
3 Additional information ... ................................................................................ 11
D to go online with STARTER via USB .................................. 11Select and install the PG/PC interface "S7USB"................................ 11Setting the access point. .................................................................... 12Activate driver installation................................................................... 13Select accessible nodes ..................................................................... 14Load the hardware configuration into the project ............................... 15E regarding series commissioning with the same Control Units17F regarding series commissioning with various Control Unit
versions, offline/online ........................................................ 20Version upgrade in the project, offline ................................................ 20G regarding the online connection via USB after a device has
been replaced and different serial numbers. ...................... 23Open the project and select accessible nodes................................... 23
Preconditions for an online connection between STARTER andSINAMICS G120 via USB
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 3/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
1 Preconditions for an online connectionbetween STARTER and SINAMICS G120via USB
The latest version of STARTER (V4.3.3) must be installed.The CU (Control Unit) is connected to the PC USB port using the specified USBcable or USB interface cable.
Table 1
Order number (MLFB) Description Entry ID
6SL3255-0AA00-2CA0 SINAMICS G120 PC CONVERTERCONNECTION KIT -2 3M USB CABLE FORCONTROL UNITS CU230P-2 CU240B-2,CU240E-2 AND SINAMICS G120C
35068034
6SL3555-0PA00-2AA0 USB INTERFACE CABLE FORCOMMISSIONING ET 200PRO FC,SINAMICS G110D, G120D AND SIRIUSM200D 2.5 M LONG INCLUDING DRIVERCD
35068235
NOTE This FAQ is valid only for WINDOWS XP Computer
What do I do if …?
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 4/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
2 What do I do if …?A. after installing/updating STARTER, I cannot establish an online connection
via USB?
Countermeasure/remedy: Close STARTER Open the registry with "regedit" Open the folder
HKEY_LOCAL_MACHINE\SOFTWARE\SIEMENS\SINEC\LogDevices\S7USB If the entry is missing, the content should be displayed as follows
Fig. 1 Incomplete registry entry
Delete the S7 USB folder Open STARTER Connect the USB cable to the CU. The system creates a new "S7USB" folder
with the following content. Depending on the software packages installed, thefollowing syntax should be displayed in "S7USB". If this is not the case, thenthe STARTER software should be installed again.
What do I do if …?
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 5/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 2 Complete registry entry of deleting the "S7USB" folder
What do I do if …?
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 6/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 3 Complete registry entry of deleting the "S7USB" folder
B. after "withdrawing" and "inserting" the USB cable, a USB connection can nolonger be established?This problem depends on which Intel chip was installed for the USB host controller;it only occurs under Windows XP and the "Intel 5 Serie 3400" chipset. This problemis manifested by the USB port freezing in the device manager. The SINAMICSG120 is no longer detected after inserting the USB cable. Further, it is no longerpossible to detect the MMC card in the SINAMICS G120.
Countermeasure/remedy: Reboot the computer,
or Upgrade to WIN7 64 bit
What do I do if …?
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 7/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 4 Intel USB host controller
Fig. 5 SIMATIC USB installed by S7DOS
What do I do if …?
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 8/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 6 If the USB cable is inserted at the Control Unit, then the driver is installed inthe SIMATIC USB device as "SINAMICS G120".
C. after installing/updating STARTER, I cannot establish an online connectionvia USB, however the registry entries are OK?
Countermeasure/remedy:1. Check the registry entries.2. Upgrade the operating system to WIN7 64bit
Check the registry entries: Close STARTER Open the registry with "regedit" Open the folder
HKEY_LOCAL_MACHINE\SOFTWARE\SIEMENS\SINEC\DefDevices\DefaultLogDevices\S7USB
The correct content of the registry entry should look like this:
What do I do if …?
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 9/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 7 Correct registry entry
Open the folderHKEY_LOCAL_MACHINE\SOFTWARE\SIEMENS\SINEC\LogDevices\S7USB
The correct content of the registry entry should look like this:
What do I do if …?
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 10/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 8 Correct registry entry
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 11/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
3 Additional information ...D to go online with STARTER via USB
1. Open STARTER2. Create a project3. Select „S7USB“ in the PC/PG Interface.
Proceed as follows if the "S7USB" interface is not installed:
Select and install the PG/PC interface "S7USB"Fig. 9 Selecting and installing the interface
Fig. 10 The "S7USB" interface is installed
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 12/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Setting the access point.For USB, the point-to-point "DEVICE (STARTER, SCOUT)" must be selectedFig. 11 Setting the access point.
Additional information on the topic: FAQ Entry ID: 67474312
Connect the Control Unit to the PC/notebook using the USB cableIt can occur that the USB driver is only installed now
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 13/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Activate driver installationFig. 12 Activate driver installation
Exit driver installationFig. 13 Exit driver installation
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 14/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Select accessible nodesFig. 14 Accessible nodes
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 15/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Load the hardware configuration into the projectFig. 15 Load the HW Config
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 16/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Close the "Online/offline comparison" windowFig. 16 Online/offline comparison
Online status – symbol is greenFig. 17 Online status
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 17/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
E regarding series commissioning with the same Control Units4. Open STARTER5. Open project6. Set the PC/PG interface on the USB7. Accessible nodes – nodes found8. Click on online icon
Open the project and select accessible nodesFig. 18 Open the project
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 18/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Activate the online connection via the iconFig. 19 Online
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 19/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Connect to the target deviceFig. 20 Connect
The SINAMICS G120 is now connected with the PC/PG, "Online".This is marked GREEN in the project tree.
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 20/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 21 Online status
F regarding series commissioning with various Control Unit versions,offline/online
Version upgrade in the project, offline Open STARTER Open project offline Set the PC/PG interface on the USB Right click on "Drive device" Click on "Target device", "Upgrade device version/device type" Select "Available device version(s)" Click on "Upgrade" Click on "Yes" A confirmation note is displayed once the operation has been successfully
completed.
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 21/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Open the project offlineFig. 22 Open the project "OFFLINE"
Upgrade the firmware in the projectFig. 23 Sequence when upgrading the firmware in the project
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 22/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 24 Select upgrade version
Fig. 25 Note: all STEP 7 applications must be closed (confirm with "Yes").
Fig. 26 The firmware upgrade has been successfully completed
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 23/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
G regarding the online connection via USB after a device has been replacedand different serial numbers.
Note After a node has been replaced, the serial number (of theSINAMICS G120) is checked when a connection is beingestablished. In this case, when establishing the connection via USB,problems can be encountered.
Open STARTER Open the project Set the PC/PG interface on the USB Accessible nodes – nodes found Click on online icon
Open the project and select accessible nodesFig. 27 Select accessible nodes
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 24/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Activate the online connection via the iconFig. 28 Online
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 25/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Connect to the target deviceFig. 29 Connect
The SINAMICS G120 is now connected with the PC/PG, "Online".This is marked GREEN in the project tree.
Additional information ...
USB connection with SINAMICS G120; ID: 85574448
Version 1.1; FAQ-01PAQUW2 14.01.2014 26/26
Cop
yrig
htSi
emen
sAG
2013
Allr
ight
sre
serv
edFA
Q-0
1PAQ
UW
2_ST
ARTE
R_V
4-3-
x_U
SB-c
onne
ctio
n-is
sues
_V1-
1_en
.doc
x
Fig. 30 Online status
The new Control Unit with serial number can be seen in parameter p7758Figure 31