state bank of india administrative office zone … 2 of 15 tender form the, chief manager [gb] state...
TRANSCRIPT
Page 1 of 15
TENDER DOCUMENT
STATE BANK OF INDIA
Administrative Office Zone –I
Bull Temple Road
Bangalore-19
Name of Work: ‘’ PROVIDING INTERIOR FURNISHING WORKS FOR NEWLY PROPOSED S.B.I.RACPC AT
YALAHANKA NEW TOWN AT PRESTIGE TOWER, OUTER RING ROAD YALAHANAKA BANAGLORE ‘’
LAST DATE OF SUBMISSION:
ON OR BEFORE 03.00 PM
LAST DATE OPENING:
23.06.2017 At 03.30 PM
Chief Manager [GB]
Page 2 of 15
TENDER FORM
The,
Chief Manager [GB]
State Bank of India
Administrative Office, Zone –I
Bangalore-4
Dear Sir,
1. Having examined the tender documents contained thereby relating to the words specified in. The
memorandum herein after set out and having visited the examined the source of works specified in the said
memorandum and having acquired the requisite information relating thereto affecting the tender. I / We
hereby offer to execute the works specified in the said memorandum at the rates mentioned in the bill of
quantities hereto and in accordance with all respects of specifications, and instructions in writing referred to
in the tender notice, General Conditions of contract, Schedule of quantities in all other respects accordance
with such conditions so far as they may be applicable.
MEMORANDUM
2. Date of commencement : within 7 days from the date of work order or
Letter of intent
3. Period of completion : 30 days from the date of issue of work order
4. Defects liability period : 6 months from the date of virtual
Completion & submission/payment
Of final bill
5. Liquidated damages [penalty] : ½% per week subject to max of 5%
6. Supplier before quoting should compulsorily make a site visit and understand the work to be done
7.Should the tender be accepted, I/ we hereby agree to abide and fulfill the terms and provisions of the said
conditions of contract.
Page 3 of 15
NOTICE INVITING TENDER
1. Sealed item rate tender for ‘’ PROVIDING INTERIOR FURNISHING WORKS FOR NEWLY PROPOSED
S.B.I.RACPC AT YALAHANKA NEW TOWN AT PRESTIGE TOWER , OUTER RING ROAD YALAHANAKA
BANAGLORE ‘’
2. Tenderer is advised to go through all the documents in connection with this contract carefully.
3. Tenderer shall deposit the sealed tender in the Office of The Chief Manger [GB] State Bank Of India
Administrative Office Zone –I Bull Temple Road Bangalore - 4 Tenderer shall deposit the sealed envelopes
separately containing the following
PART ‘B’
1. Schedule of quantities duly filled in figures and words and signed on each page with seal and date
Tenders will be received up to A.M. On and shall be opened on the same day @
At the Office of The Regional Business office –I administrative office Zone -I STATE BANK
OF INDIA, Administrative Office Bangalore-4. Tenders received after fixed time and date due to postal
delay will not be considered.
2. Tenders not properly filled, mutilated with incorrect calculations or generally not complying with
conditions will be rejected.
3. Tenderer should quote their rates both in figures and in words. The Schedule of quantities must be fully
priced with rates quoted for both unit rate specification and the total of each page along with carried
over figures of previous page shall be given in ink and signed by the Tenderer. No blank space shall be
left. Figures in words shall be deemed to be final figures, in case of cuttings or over writings. However, it
is essential that the contractor should ensure that he has signed on all pages of the tender document.
4. PERIOD OF VALIDITY
The tender shall remain valid for acceptance of a period of 90 days from the date of submission of tenders.
If any Tenderer with draw his tender before the said period or make any modifications in the terms and
conditions of the tender, then the employer has the liberty to disqualify the Tenderer
Every Tenderer is expected to inspect the site of the proposed work and acquaint him with site conditions,
approaches, availability of the raw materials, geological and weather conditions etc. before quoting his rates.
He must go through all the specifications, and other tender documents. Any further clarifications in the
documents can be had from this Office at the above mentioned address.
5. QUANTUM OF WORK
Page 4 of 15
A schedule of probable quantities in respect of each work and specifications accompany these conditions.
The schedule of probable quantities is liable to alterations, omissions or additions at the discretion of the
Bank. The schedule of the probable quantities may vary considerably on the higher or lower side.
6. ALL INCLUSIVE RATES
Quoted Rate shall include the cost of transportation of material to the site, all taxes such as sales tax, excise
duty, octroi, works contract and any other statutory levy, etc. and fixing or placing in position for which the
item of work is intended to be operated. The rates quoted by the contractor shall be firm throughout the
contract period and there shall be no upward revision of the rates. It should be clearly understood that any
claims for extra sales tax, excise duty, octroi, works contract and any other statutory levy, etc shall not be
entertained in any case whatsoever once tenders are opened.
11. INTERPRETING SPECIFICATIONS
In interpreting specifications, the following order of decreasing importance shall be followed:
1. Schedule of quantities with detail specifications
2. Unit rate specifications and technical specifications
3. General Specifications
Matters not covered by the specifications given in the contract, as a whole shall be covered by the relevant
Indian standard codes. If such a Codes on a particular subject have not been framed, the decision of the Bank
Engineer shall be final.
12. The acceptance of the tender shall rest with the authorized representative of the employer, who does not
bind himself to accept the lowest tender and reserves to himself the authority to reject any or all the tenders
received without assigning any reasons, whatsoever.
13. The work shall be carried out under the direction and supervision of the Bank Engineer or their
representative at site. On acceptance of the tender, the contractor shall intimate the name of his accredited
representative who would be supervising the work and would be responsible for taking instructions for carrying
out the work.
14. Bank Engineer decision with regard to the quality of material and workmanship will be final and binding,
any material rejected by the Bank Engineer shall be immediately removed from the site by the
Contractor.
Page 5 of 15
15. SUB-LETTING
No part of the contract shall be sublet without the written permission of the employer nor shall transfers be
made by the power of attorney authorizing others to carry out the work or receive payment on behalf of the
renderer.
16. DEFECTS LIABILITY PERIOD
Any defect developed within the defect liability period of 6 months will have to be rectified by the agency at
their own cost and in case and the defects are not rectified by the contractor, employer or their
representative shall get the work done at the risk and cost of the contractor.
17. CERTIFICATE OF VIRTUAL COMPLETION
The work shall not be considered as completed until the Bank has issued in writing “certificate of virtual
completion” stating that the work has been completed and defects liability period shall commence from such
certified date of virtual completion.
18. DELAYS IN COMMENCEMENT
The contractor shall not be entitled to any compensation for any loss suffered by him on account of delays in
commencing or executing the work, whatever the cause for such delays may be including delays in procuring
government controlled or other materials.
19. The contractor should inspect the source of material, their quality, quantity, and availability. The
material must strictly comply with the relevant specifications attached.
20. PERIOD OF COMPLETION
Time is deemed to be the essence of the contract; the completion period shall be twenty days. The contractor
shall draw a detailed schedule of program in the form of BAR/PERT CHART of whole work, within two weeks of
the award of the work and submit to the Bank for its approval.
21. CONTRACTORS STORE
Page 6 of 15
Suitable area near the site of work shall be allowed to the contractor free of cost for storing his tools and
plants, materials and for his site office. The contractor shall remove all temporary constructions constructed
by him at site for the purpose of completing the work after the work is over
22. MEASUREMENT AND BILLING
Whenever mode of measurement is specified, measurement will be taken at site as per the latest IS code of
practice for measurement.
The contractor or his representative shall accompany the employer or their representative in taking/checking
Measurements. All necessary tapes and shall be supplied by the Contractor. The Contractor shall then
present his bill based on the agreed and recorded measurements and if the contractor fails to accompany the
employer for measurement, then he shall be bound by the Measurement s taken by the Bank Engineer
Contractor shall raise first and final bill or for minimum payment of a Running Bill
Payment towards all interim bills will be made by the employer within the time limit specified in the summary,
form of the tender
Period of final measurement shall be 30 days from the date of completion of the project.
23. WATER AND ELECTRICITY
The employer will make water supply and electricity to the site at one convenient point available. The
contractor should make his own arrangements in case of supplementary supply points are required for both
water and electricity. The consumption charges shall be borne by the contractor.
24. INSURANCE
The successful contractor shall take out the contractor’s all risk insurance policy, jointly in the name of the
employer and the contractor and the original policy shall be deposited with the employer. The insurance policy
shall be obtained within 14 days of date of commencement of the work
25. STATUTORY REGULATION
The whole work is to be complied with as per the requirements and by laws of relevant statutory authorities,
including contract labor (Regulation and Abolition) act 1970.
I/ We hereby declare that I/We read and understood the above instructions and the terms and conditions
mentioned above are binding on me/us.
PLACE:
DATE: SIGNATURE WITH SEAL
Page 7 of 15
SATE BANK OF INDIA
ADMINISTARTIVE OFFICE-ZONE –I
BANGALORE
NAME OF WORK: PROVIDING INTERIOR FURNISHING WORKS FOR NEWLY PROPOSED S.B.I RACPC BRANCH AT
YALAHANKA NEW TOWN, BENGALURU
TENDER SHEDULE :
Sl no Items of work Unit Qty Rate Amount
1 HIGH LEVEL PARTITION:
Providing and fabricating High level partition up to the
ceiling height by using well seasoned
Sal/Honne/Mathi/ Nandi wood of section 40 mm x 60
mm /Plain Aluminum section of size 38 mmx 63 mmx
1.5 mm spacing at 600 mm center to center vertically
and horizontally at floor, sill and at top one member
touching up to ceiling. The framework shall be
assembling with proper wooden joineries required
fevicol nails zigzag clamps at junctions. Over the
frame work 6 mm ply of approved make Regal / Uniply
/ Archid ply / Amul / Well ply shall be fixed with
headless Niles and required fevicol and required
opening shall be left to fix the Door, Glass, and shall
be fixed with glass of 8 mm thick glass with required
etched glass design, beach wood / 12 mm ply shall be
used to fix the glass and shall be laminated with 1 mm
thick, if wood beading shall be directed shall be
polished with color polish to match the laminate all
round lipping with 4 mm ply. Over the frame work 6mm
ply of grade BWP/BWR Regal / Uniply / Archid ply /
Amul / Well ply approved make shall be fixed with
required fevicol head less nails, lastly over the ply
1mm thick laminate of approved make shall be fixed
with required fevicol finished neatly etc complete.
This rate Includes cost of all materials, labor, and
taxes, lead and lift, to the place of work.
Sqmt
40.00
Rupees in words
2 LOW HEIGHT PARTITION:
Providing and fabricating low level partition up to 1.50
mt height by using well seasoned
sal/honne/mathi/champa wood of section 40 mm x 60
mm/Plain Aluminum section of size 38 mmx 63 mmx 1.5
mm at 600 mm center to center vertically and
horizontally at floor, sill and at top one member
touching up to1.5 mt ht. The framework shall be
assembling with proper wooden joineries required
fevicol nails zigzag clamps at junctions. Over the
frame work6 mm ply of approved make Regal / Uniply /
Archid ply / Amul / Well ply shall be fixed with
headless Niles and required fevicol and required
opening shall be left to fix the glass of 10 mm thick
(Cost of the shall be paid separately), the glass shall
Page 8 of 15
be fixed with required Beach wood beading with 4 mm
ply all round lipping before fixing the glass / Shall be
fixed with 12 mm ply later laminated with 1 mm thick
laminate. Over the skeleton frame work 6mm ply of
approved BWP/BWR ply Regal / Uniply / Archid ply /
Amul / Well ply and make shall be fixed with required
fevicol head less nails, over the ply 1 mm thick
laminate of approved make and shade matt /suede
shall be fixed with required fevicol finished neatly etc
complete. This rate includes cost of all materials,
labor, and taxes, lead and lift, to the place of work.
Sqmt
150.00
Rupees in words
3 FLOOR PEDESTAL UNIT:
Providing and fabricating floor pedestal unit of size
0.40 mt x 0.50 mt x 0.76 mt size by using approved
make Regal / Uniply / Archid ply / Amul / Well ply
BWP/BWR block board / Ply the draw box unit will
have three no of drawer unit of size 400 x 500 x 150
mm which shall be fabricated by using full paneled
drawer sliding unit of make Ebco with 19mm block
board for the front and 12 mm thick for the bottom
draw unit. At bottom one shutter shall be fixed with
Ebco make flap/Box hinges either if one drawer
cancelled. At the bottom all cut edges of the block
board shall be fixed with beach wood beading lipping
finished neatly with color less polish front exposed
surface of unit shall be fixed with 1mm thick
lamination of approved make and shade with required
fevicol finished neatly .all hardware materials are of
standard type like stainless Steel handles of approved
make, multi lock is of Laxmi / Godrej. Inner surface of
the unit shall be painted with Enamel paint followed by
pop putty Etc complete This rate includes cost of all
materials, labor, taxes, lead and lift, to the place of
work.
No
26.00
Rupees in words
4 STORAGE CABINET HIGH LEVEL UPTO 1.52 MT HT
Providing and fabricating full height floor Storage
cabinet as per the design by using 19 mm BWP / BWR
block board / Ply of approved make. The cabinet
fabricated all round block board of 0.45/0.40 -mt
widths to form a box at rear side shall be Fixed with 9
mm thick ply. Front shall be fixed with two half
shutters according to the size of cabinet. The cabinet
will also have equal partition shelves inside. Inside and
front lipping shall be done by 6 mm ply to form the
grove .All cut edges of the block boar shall be fixed
with beach wood beading shall be polished finished
with color less polish finished neatly .All exterior
surface of the block board shall be fixed with 1mm
thick lamination with required fevicol finished neatly,
all interior surface of the block board shall be
finished with two coats of enamel paint followed by
Page 9 of 15
pop putty and primer. Lastly the cabinet will get fitted
with H/D type s.s handles of size 15 cm, multi lock,
hinges, laminated Etc complete This rate includes cost
of all materials, labor, and taxes, lead and lift, to the
place of work.
Sqmt
5.00
Rupees in words
5 STORAGE CABINET LOW LEVEL UPTO 0.90 MT HT
Providing and fabricating full height floor Storage
cabinet as per the design by using 19 mm BWP / BWR
block board / Ply of approved make. The cabinet
fabricated all round block board of 0.45/0.40 -mt
widths to form a box at rear side shall be Fixed with 9
mm thick ply. Front shall be fixed with two half
shutters according to the size of cabinet. The cabinet
will also have equal partition shelves inside. Inside and
front lipping shall be done by 6 mm ply to form the
grove .All cut edges of the block boar shall be fixed
with beach wood beading shall be polished finished
with color less polish finished neatly .All exterior
surface of the block board shall be fixed with 1mm
thick lamination with required fevicol finished neatly,
all interior surface of the block board shall be
finished with two coats of enamel paint followed by
pop putty and primer. Lastly the cabinet will get fitted
with H/D type s.s handles of size 15 cm, multi lock,
hinges, laminated Etc complete This rate includes cost
of all materials, labor, and taxes, lead and lift, to the
place of work.
Sqmt
22.00
Rupees in words
6 SIDE CREDENZA UNIT:
Providing fabricating side credenza unit of size 1.82
mt x 0.40 mt x 0.76-mt sizes for specified areas.
The cabinet shall be fabricate by using 19 mm thick
block board /Ply , 12 mm ply, 6 mm ply, of approved
make BWP/BWR grade .The drawer unit get fitted
with full paneled metal drawer Sliding unit of make
Ebco S.S handles, multi locks. The, exterior surface of
the unit shall be fixed with 1 mm thick lamination of
approved make Mat/Suede finish with required fevicol
finished neatly, the interior surface of the unit shall
painted with two coats of enamel paint followed by
p.o.p putty and primer Etc complete This rate includes
cost of all materials, labor, and taxes, lead and lift, to
the place of work.
No
15.00
Rupees in words
7 SIDE CREDENZA UNIT:
Providing fabricating side credenza unit of size 1.40
mt x 0.40 mt x 0.76-mt sizes for specified areas.
The cabinet shall be fabricate by using 19 mm thick
block board /Ply , 12 mm ply, 6 mm ply, of approved
make BWP/BWR grade .The drawer unit get fitted
Page 10 of 15
with full paneled metal drawer Sliding unit of make
Ebco S.S handles, multi locks. The, exterior surface of
the unit shall be fixed with 1 mm thick lamination of
approved make Mat/Suede finish with required fevicol
finished neatly, the interior surface of the unit shall
painted with two coats of enamel paint followed by
p.o.p putty and primer Etc complete This rate includes
cost of all materials, labor, and taxes, lead and lift, to
the place of work.
No
15.00
Rupees in words
8 WORK STATION:
Providing and fabricating workstation of size 2.20
mtx0.76 mt x 0.76 mt deep with one side draw box
unit of size 450 mm width x500 mm deep x750mm
height comprising three no of drawer unit. The whole
unit shall be fabricated by using 19 mm thick block
board /Ply of approved make Regal / Uniply / Archid
ply / Amul / Well ply BWP/BWR grade as per the
design and drawing, exterior surface of the unit shall
be fixed with 1mm thick lamination of approved make
with required fevicol .The draw box unit get fixed
with full panel drawer sliding unit of make Ebco/Zip
co, multilocks, H/D type stainless steel handles .The
inner surface of the unit shall be painted with two
coat of primer & Enamel paint by pop putty, all cut
edges of block board shall be fixed with flat beach
wood beading finished with color less polish finished
neatly Etc complete This rate includes cost of all
materials, labor, and taxes, lead and lift, to the place
of work.
No
1.00
Rupees in words
9 WORK STATION:
Providing and fabricating workstation of size 1.82
mtx0.76 mt x 0.76 mt deep with one side draw box
unit of size 450 mm width x500 mm deep x750mm
height comprising three no of drawer unit. The whole
unit shall be fabricated by using 19 mm thick block
board /Ply of approved make Regal / Uniply / Archid
ply / Amul / Well ply BWP/BWR grade as per the
design and drawing, exterior surface of the unit shall
be fixed with 1mm thick lamination of approved make
with required fevicol .The draw box unit get fixed
with full panel drawer sliding unit of make Ebco/Zip
co, multilocks, H/D type stainless steel handles .The
inner surface of the unit shall be painted with two
coat of primer & Enamel paint by pop putty, all cut
edges of block board shall be fixed with flat beach
wood beading finished with color less polish finished
neatly Etc complete This rate includes cost of all
materials, labor, and taxes, lead and lift, to the place
of work.
No
6.00
Rupees in words
Page 11 of 15
10 WORK STATION:
Providing and fabricating workstation of size 1..52
mtx0.76 mt x 0.76 mt deep with one side draw box
unit of size 450 mm width x500 mm deep x750mm
height comprising three no of drawer unit. The whole
unit shall be fabricated by using 19 mm thick block
board /Ply of approved make Regal / Uniply / Archid
ply / Amul / Well ply BWP/BWR grade as per the
design and drawing, exterior surface of the unit shall
be fixed with 1mm thick lamination of approved make
with required fevicol .The draw box unit get fixed
with full panel drawer sliding unit of make Ebco/Zip
co, multilocks, H/D type stainless steel handles .The
inner surface of the unit shall be painted with two
coat of primer & Enamel paint by pop putty, all cut
edges of block board shall be fixed with flat beach
wood beading finished with color less polish finished
neatly Etc complete This rate includes cost of all
materials, labor, and taxes, lead and lift, to the place
of work.
No
2.00
Rupees in words
11 L-TYPE TABLE :
Providing and fabricating and fixing the L-Type works
station of size 1.50 mt x 0.60 mt at one side and 1.50
mt x 0.60 mt at another side to form L shape as per
the design and drawing all edge shall be fixed with the
flat beading and shall be polished with color less polish
the work station shall be laminated with 1 mm thick of
approved make and under Neath shall be primered
painted with red oxide and fixed in to the cubical as
shown in the drawing Etc complete This rate includes
cost of all materials, labor, and taxes, lead and lift, to
the place of work.
No
23
Rupees in words
12 CONTINUOUS TABLE:
Providing and fabricating by using 19 mm thick Block
Board /Ply of Regal / Uniply / Archid ply / Amul / Well
ply BWP /BWR wall to wall continues table, tabletop of
width 0.60-mt width. The table top shall be cut in
between the floor pedestal units to insert the cord,
the table top edge (front) shall be of 50 mm thick
shall be fixed over the pre fabricated floor pedestal
unit (shall be paid separately) at 1.22 mt distance the
table top shall be fixed with 1mm thick lamination of
approved make and color with required fevicol fixed
neatly. All cut edges of the block Board Ply shall be
fixed with flat beach wood beading finished neatly
with color less polish etc complete. This rate includes
cost of all materials, labor, and taxes, lead and lift, to
the place of work.
Rmt
7.00
Rupees in words
13 TUFFENED GLASS PARTITION :
Page 12 of 15
Providing and fixing 12 mm thick float toughened Glass
of approved make Saint Gobin/Asahi/Modi float,
neatly buffed edges polishing as per Design and fixing
the Glass with required ozone /patch fitting over the
ground and to the top portions finished neatly, Etc
complete This rate includes cost of all materials,
labor, and taxes, lead and lift, to the place of work.
Sqmt
6.00
Rupees in words
14 TUFFENED GLASS DOOR :
Providing and fixing 12 mm thick float toughened Glass
Door of approved make Saint Gobin/Asahi/Modi float,
neatly buffed edges polishing as per Design and fixing
the Glass with required ozone / dorma medium
capacity auto door closure fixing in the floor with
cutting redoing the floor with required pivot fittings
and fixing Etc complete This rate includes cost of all
materials, labor, and taxes, lead and lift, to the place
of work.
Sqmt
2.00
Rupees in words
15
DOOR FRAME :
Providing and fabricating and fixing the door frame of
beach wood of section 63 mm x 50 mm saw mill finish
with necessary grove to fix the door shutter fixing
the frame to the existing partition or wall opening
with required screw, hold fast melamine polishing
finishing neatly etc complete This rate includes cost
of all materials, labor, and taxes, lead and lift, to the
place of work.
Rmt
15.00
Rupees in words
16 FLUSH DOOR SHUTTER:
Providing and fabricating Flush Door shutter of
approved make of thick 32mm BWP/BWR Grade. All
cut edges of the block Board shall be fixed with Beach
wood Beading over the prefixed 4 mm thick ply (lipped
ply) to form groove all round the periphery, over the
shutter 1mm thick lamination of approved make and
color mat/ suede finished shall be fixed on both the
sides with required fevicol finished neatly all beading
surface shall be polished with color less polish finished
neatly. The shutter will also get fitted with 6 MM
Glass made slit at left /right hand side 150 mm x 1500
mm fixed with flat beading finished neatly and hard
ware materials like Godrej night latch/Auto
Lock/Barrel Lock, stainless steel handles of size 200
mm cm Etc complete This rate includes cost of all
materials, labor, and taxes, lead and lift, to the place
of work.
Sqmt
2.00
Rupees in words
17 COMPUTER KEY BOARD UNIT:
Providing and fabricating and fixing the computer Key
Page 13 of 15
Board of size 0.60 mt x 0.46 mt by using 19 thick ply
of approved make of BWP/BWR grade neatly cut and
fixed with all round flat beading and laminate of 1 mm
thick approved make and color and fixing the board
by telescopic sliding unit which should have ball roller
or readymade EBCO make computer Keyboard with
mouse pad . Etc complete This rate includes cost of
all materials, labor, and taxes, lead and lift, to the
place of work
No
35.00
Rupees in words
18 VERTICAL BLINDS:
Providing and fixing fabric VERTICAL blinds of
approved make and color with its all accessories in
good condition. Etc complete This rate includes cost of
all materials, labor, and taxes, lead and lift, to the
place of work.
Sqmt
150.00
Rupees in words
19
VOTCHER WRITING TABLE:
Providing and fabricating by using 19 mm block Board
/Ply of approved make Voucher writing table of size
1.22 mt x 0.30 mt x 0.80 Mt ht as per design and
Drawing Etc complete This rate includes cost of all
materials, labor, and taxes, lead and lift, to the place
of work
No
2.00
Rupees in words
20 BLOCK BOARD FOOT REST:
Providing and fabricating block board foot rest by
using 19 mm Block Board /Ply Of approved make of
size 1mt x .60 mt tapered at foot end making the box
and keeping in position premiered the surface Etc
complete This rate includes cost of all materials,
labor, and taxes, lead and lift, to the place of work
No
35.00
Rupees in words
21 PIN HEAD BOARD:
Providing and fixing the pin head Board by using Soft
Board, good Quality upholstery wrapped around and
sandwiched at back with 6 mm ply and fixed over the
surface Etc complete, this rate includes cost of all
materials, labor, taxes, lead and lift and other levies
to the place of work
Sqmt
10.00
Rupees in words
22 GYPSUM BOARD FALSE CEILING:
Providing and fixing Gypsum board false ceiling as,
with tier up and tier down box type design, the false
ceiling also should be cut opened where ever as
specified in circular /square shape, of required size to
fix the light fittings. The false ceiling shall be
fabricated and fixed by using companies specified
fixing materials like perimeter channels, G.I
Page 14 of 15
intermediate channels, ceiling angles, Knurled web etc
shall be fixed to the ceiling with self expanding
screws hanged to the ceiling according to the spirit
level, plumb line below the fixed frame 12.5 mm thick
gypsum board false ceiling shall be fixed with flat star
head screws by mode of screw fasteners .The ceiling
bottom of the false ceiling shall be finished with two
coats of Emulsion paint of Berger make and color
finished with roller brush . Etc complete This rate
includes cost of all materials, labor, and taxes, lead
and lift, to the place of work.
Sqmt
100.00
Rupees in words
23 GRID SYSTEM OF FALSE CEILING :
Providing and fixing USG/ARM STRONG make Grid
Silhouette system of False ceiling by using company
specified wall angle, main runner ,1200 mm cross tee
,600 mm cross tee ,hanging wires 2 mm dia .90 mt
length successive hooks rawl plugs fixing at every
junction of the cross tee . All the fixtures fixed for
fluid level and checked for the level .After the frame
grid formation 12 mm thick approved tile of size 600
mm x 600 mm shall be laid inside the grids and
checked for level and adjusted Etc complete This rate
includes cost of all materials, labor, and taxes, lead
and lift, to the place of work
Sqmt
300.00
Rupees in words
24 WALL PANELLING DESIGN:
Providing fabricating wall paneling as per design and
drawing by using approved BWP/BWR grade
combination of 19 mm block board, 12 mm, and 6 mm
ply 1 mm thick lamination. The paneling shall be fixed
over the specified area in such a way that 19 mm block
board of 80 mm width frame work shall be fixed over
the wall according to the plumb line and length & at
600 mm c/c horizontally vertically, over which 12mm
ply 6 mm ply shall be fixed with necessary head less
nails with fevicol in such a way that even 12 mm ply
may get over lapped to form extra layer. Over the ply
1 mm thick lamination of approved make shall be fixed
the design may vary according to the site condition
and the designed on the spot contractor shall agree to
the sketches as made & fabricated neatly. Etc
complete This rate includes cost of all materials,
labor, and taxes, lead and lift, to the place of work.
Sqmt
60.00
Rupees in words
Page 15 of 15
25 TEXTURED PAINT:
Providing wall textured paint by using the wall care
putty of approved make and creating textured surface
by using special tools and applying the surface with
the emulsion paint of approved color and make and
finishing neatly Etc complete This rate includes cost
of all materials, labor, and taxes, lead and lift, to the
place of work
Sqmt
60.00
Rupees
24 EMULSION PAINT:
Providing wall emulsion paint of approved make &
color with JK wall care putty and finishing neatly with
sponge roller ,brush Etc complete This rate includes
cost of all materials, labor, and taxes, lead and lift, to
the place of work
Sqmt
.
200.00
Rupees in words
26 DECORATIVE WALL PAPER:
Providing and fixing the decorative wall paper of
approved make and color with recommended adhesive
cleaning the surface with required JK wall putty finish
etc complete This rate includes cost of all materials,
labor, and taxes, lead and lift, to the place of work
Sqmt
25.00
Rupees in words
27 Providing and fixing the 8 mm glass with required stud
bolts over the wall surface where ever as directed
with graphic Branding stickers as per the design and
graphic effects etc complete This rate includes cost
of all materials, labor, and taxes, lead and lift, to the
place of work
Sqmt
10.00
Rupees in words
Total