stoarmat render system drawing register 2017 render system on... · stoarmat render system timber...

Drawing Description Drawing No.

Drawing Register

Introduction Series 000 FCS 001 - 004StoArmat Render System - Introduction FCS 005StoArmat Render System - Fibre Cement Sheet Information FCS 006StoArmat Render System - Sheet Layout FCS 007StoArmat Render System - Sheet and System Layout FCS 008

Sheet Layout Series 100StoArmat Render System StoArmat Plaster System - Isometric FCS 100

Foundation Series 200StoArmat Render System Foundation Slab-on-ground FCS 200StoArmat Render System Rebated Foundation Slab-on-ground - Rendered Finish FCS 201StoArmat Render System Conc.Foundation/Timber Floor FCS 202StoArmat Render System Conc.Block Foundation Edge Detail FCS 203StoArmat Render System Solid Conc.Foundation Edge Detail FCS 204StoArmat Render System Ribraft Floor System / Edge Detail FCS 205StoArmat Render System Maxraft Floor System / Edge Detail FCS 206

Walls Series 300StoArmat Render System Vertical Sheet Join FCS 300StoArmat Render System Horizontal Sheet Join FCS 301StoArmat Render System External Corner FCS 302StoArmat Render System Internal Corner FCS 303StoArmat Render System Vertical Control Joint FCS 304StoArmat Render System Horizontal Junction - Non Draining - Opt 1 FCS 305StoArmat Render System Horizontal Junction - Non Draining - Opt 2 FCS 306StoArmat Render System Horizontal Junction - Draining FCS 307

Wall Penetrations & Fittings Series 350StoArmat Render System Pipe Penetration (up to 100mm)Detail FCS 350StoArmat Render System Light Fitting/Fixing Detail FCS 351StoArmat Render System Tap Fitting/Fixing Detail FCS 352StoArmat Render System Handrail Bracket/Fixing Detail FCS 353StoArmat Render System Meterbox FCS 354StoArmat Render System Downpipe Saddle Fixing & Wiring Details FCS 355StoArmat Render System Fan Vent Detail FCS 356

THESE DETAILS ARE ISSUED AS A GUIDE USING STANDARD BUILDING PRACTICES BASED ON THE NZBC.VARIOUS BUILDING COMPONENTS ARE DETAILED AND IT IS THE RESPONSIBILITY OF EACH TRADE INVOLVED TOENSURE THAT THEIR PARTICULAR ELEMENTS ARE INSTALLED CORRECTLY. NOTE: REFER TO INDIVIDUALMANUFACTURES FOR CURRENT DETAILS AND SPECIFICATIONS - SEE www.sto.co.nz FOR CURRENT DETAILS.RBW DETAILS MUST BE ISSUED BY A; REGISTERED ARCHITECT, LICENSED DESIGNER OR CHARTERED ENGINEER

STO DRAWING REGISTER

PAGE 1 OF 4

The information contained on this page is based on our experience and research at the date of issue. The detail is for use by RegisteredArchitects, Licensed Designers or Chartered Engineers to assist in developing project details using Sto Systems. Stoanz Ltd reserve the right toalter or update information at any time without prior notice and it is the responsibility of the designer, project manager or Sto contractor to insurethey have and use the current Sto details and specifications on site.

STO/ MONOTEK

STOARMAT RENDER SYSTEM

DRAWING REGISTER

FCS 001

2017


Joinery Series 400StoArmat Render System Alu.Joinery - Head Detail FCS 400StoArmat Render System Alu.Joinery - Sill Detail FCS 401StoArmat Render System Alu.Joinery - Jamb Detail FCS 402StoArmat Render System Int.Cnr.Alu.Window/Door Joinery FCS 403StoArmat Render System Entry Door - Head Detail FCS 404StoArmat Render System Entry Door - Threshold Detail FCS 405StoArmat Render System Entry Door - Jamb Detail FCS 406StoArmat Render System Sliding Door - Head Detail FCS 407StoArmat Render System Sliding Door - Threshold Detail/Concrete Floor FCS 408StoArmat Render System Sliding Door - Threshold Detail/Timber Floor FCS 409StoArmat Render System Sliding Door - Jamb Detail FCS 410StoArmat Render System Bifold Door - Head Detail FCS 411StoArmat Render System Bifold Door - Threshold Detail/Concrete Floor FCS 412StoArmat Render System Bifold Door - Threshold Detail/Timber Floor FCS 413StoArmat Render System Bifold Door - Jamb Detail FCS 414StoArmat Render System Level Entry - Threshold Detail FCS 415StoArmat Render System Garage Door - Timber Head Detail FCS 416StoArmat Render System Garage Door - Timber Jamb Detail FCS 417StoArmat Render System Garage Door - Plaster Head Detail FCS 418StoArmat Render System Garage Door - Plaster Jamb Detail FCS 419

Parapets, Balustrades, Decks Series 500StoArmat Render System Parapet/Metal Flashing Detail FCS 500StoArmat Render System Rendered Parapet/Balustrade Detail FCS 501StoArmat Render System Parapet and/or Encl.Balustrade Wall Junction - Plan View FCS 502StoArmat Render System Flexible Flashing Install - Isometric FCS 503StoArmat Render System Metal Saddle Flashing & Cap Install - Isometric FCS 504StoArmat Render System StoFlexyl Meshed Saddle Flashing Install - Isometric FCS 505StoArmat Render System StoFlexyl Meshed Waterproofing Cap Install - Isometric FCS 506StoArmat Render System Balustrade/Encl.Deck Detail FCS 507StoArmat Render System Enclosed Deck Cross Section FCS 508StoArmat Render System Cantilevered Slatted Deck FCS 509StoArmat Render System Non Cantilevered Slatted Deck FCS 510StoArmat Render System Independent Slatted Deck FCS 511StoArmat Render System Timber Beam / Pergola Detail FCS 512StoArmat Render System RWH/Scupper Opening FCS 513

Soffit Series 600StoArmat Render System Flat Soffit/Wall Junction FCS 600 StoArmat Render System Raking Soffit/Wall Junction FCS 601StoArmat Render System Face Fixed Fascia FCS 602StoArmat Render System Raking Soffit Reversed FCS 603 StoArmat Render System Raking Soffit - Sto uPVC Control Joint FCS 604 StoArmat Render System Soffit to Cladding Detail FCS 605StoArmat Render System Gutter/Wall Junction FCS 606 StoArmat Render System Soffit at Window/Door Head FCS 607



PAGE 2 OF 4


STO/MONOTEK


DRAWING REGISTER

FCS 002

2015


Roof Series 700StoArmat Render System Apron (Transverse) Flashing FCS 700StoArmat Render System Parallel Apron (Parallel) Flashing FCS 701StoArmat Render System Inter-storey Transverse (Apron) Roof/Stopend FCS 702 StoArmat Render System Inter-storey Flat (Membrane) Roof/Stopend Flashing FCS 703StoArmat Render System Inter-storey Roof Stopend Flashing - PlanView FCS 704StoArmat Render System Roof Penetration Gutter (Masonry Tile) Detail FCS 705StoArmat Render System Roof Parallel Hidden Gutter FCS 706StoArmat Render System Face Fixed Fascia/Barge FCS 707StoArmat Render System Face Fixed Fascia/Membrane Roof FCS 708StoArmat Render System Roof/Wall Ridge FCS 709StoArmat Render System Framed Chimney FCS 710

Dissimilar Material

Weatherboard Series 800StoArmat Render System Ext.Corner Weatherboard/FC Sheet - Opt 1 FCS 800StoArmat Render System Ext.Corner Weatherboard/FC Sheet - Opt 2 FCS 801StoArmat Render System Ext.Corner Weatherboard/FC Sheet - Direct Fix FCS 802StoArmat Render System Int.Corner Weatherboard/FC Sheet - Opt 1 FCS 803StoArmat Render System Int.Corner Weatherboard/FC Sheet - Opt 2 FCS 804StoArmat Render System Int.Corner Weatherboard/FC Sheet - Direct Fix FCS 805StoArmat Render System Vertical Joint Flashing Weatherboard/FC Sheet FCS 806StoArmat Render System Horizontal Junction Weatherboard/FC Sheet FCS 807StoArmat Render System Gable End Weatherboard/FC Sheet FCS 808

Brick Series 810StoArmat Render System External Corner Brick Veneer/FC Sheet FCS 810StoArmat Render System Internal Corner Brick Veneer/FC Sheet - Opt 1 FCS 811StoArmat Render System Internal Corner Brick Veneer/FC Sheet - Opt 2 FCS 812

Fibre Cement Sheet Series 820 series not issued

Concrete Block Series 830StoArmat Render System External Corner Concrete Block/FC Sheet FCS 830StoArmat Render System Internal Corner Concrete Block/FC Sheet FCS 831StoArmat Render System Vertical Joint Concrete Block/FC Sheet FCS 832StoArmat Render System Horizontal Junction Concrete Block/FC Sheet FCS 833

Manufactured Stone - Schist & Natural Stone Series 840StoArmat Render System Ext.Cnr Manuf. Stone/FC Sheet FCS 840StoArmat Render System Boxed Ext.Cnr Stone Veneer/FC Sheet FCS 841StoArmat Render System Int.Cnr Manuf. Stone/FC Sheet FCS 842StoArmat Render System Vertical Junction Manuf. Stone/FC Sheet FCS 843StoArmat Render System Ext.Cnr Schist or Stone Veneer/FC Sheet FCS 844StoArmat Render System Int.Cnr Schist or Stone Veneer/FC Sheet FCS 845StoArmat Render System Vertical Junction Schist or Stone Veneer/FC Sheet FCS 846StoArmat Render System Horiz.Junction Schist or Stone Veneer/FC Sheet FCS 847



PAGE 3 OF 4


STO/MONOTEK


DRAWING REGISTER

FCS 003

2017


Continuation Dissimilar Material

Profile Metal Series 850 series not issued

StoTherm Panel EIFS Series 860 series not issued

DISSIMILAR JOINERY Series 870

TIMBER JOINERYStoArmat Render System Timber Window Joinery - Head Detail FCS 870StoArmat Render System Timber Window Joinery - Sill Detail FCS 871StoArmat Render System Timber Window Joinery - Jamb Detail FCS 872StoArmat Render System Timber Joinery - Timber Floor/Threshold Detail FCS 873StoArmat Render System Timber Joinery - Concrete Floor/Threshold Detail FCS 874

NK PVCu JOINERY series not issued

FLASHMAN JOINERY FLASHING SYSTEMStoArmat Render System Flashman Head Flashing FCS 878StoArmat Render System Flashman Sill Flashing FCS 879StoArmat Render System Flashman Jamb Flashing FCS 880HOMERIT PVC JOINERYStoArmat Render System Homerit PVC Joinery - Head Detail FCS 881StoArmat Render System Homerit PVC Joinery - Sill Detail FCS 882StoArmat Render System Homerit PVC Joinery - Jamb Detail FCS 883

MOULDINGS & SHAPESRefer to - www.accumen.co.nzLightweight exterior decorative moldings and shapes, including columns, architraves,cornices, window sills, fence caps, quoins that can be finished in Stolit K or MP spongecoloured finishing render.Note: Decorative mouldings require min. 10° MFCSope to top surface and a drip edge.



PAGE 4 OF 4


STO/MONOTEK


DRAWING REGISTER

FCS 004

2017

SS404 STOARMAT RENDER SYSTEMBRANZ CERTIFICATE No.488

1. STOARMAT JOINTING ON SHEETS JOINTS2. STOARMAT MESHED REINFORCEMENT RENDER COMPLETELY OVER CLADDING3. STOKIT K or MP COLORED FINISHING RENDER IN 25Kg PAIL. EUROPEAN FIBRE REINFORCED

NON-CEMENT COLORED FINISHING RENDER, AVAILABLE IN 1.0/1.5/2.0 & 3.0mm SIZED TEXTUREAND MP or MP NATURAL SPONGE FINISHING RENDER

4. STOCOLOR : MAXICRYL MATT FACADE PAINT 15lt PAIL: LASTIC SATIN FACADE PAINT 15lt PAIL: LOTUSAN MINERAL RESIN PAINT 15lt PAIL

STOARMAT RENDER SYSTEMBRANZ APPRAISAL CERTIFICATE No.488 & 499 INCORPORATING:

JAMES HARDIE 7.5 or 9mm - MONOTEK FIBRE CEMENT SHEET

STOARMAT FULLY MESHED RENDER SYSTEM No. 488


STO/MONOTEK


INTRODUCTION

FCS 005

2017

SCALE NTS

ALL EDGES MUST BESUPPORTED WITH H3.1 CAVITYBATTENS ON TIMBER FRAMING.

ALL SHEETS FIXED VERTICALLY

CAVITY BATTEN LAYOUT ANDFIXINGS AS PER

MANUFACTURERS DETAILS ANDWIND ZONES

FIXINGS MIN.12mm FROM SHEETEDGES 1-2mm GAP IN SHEETS

BACK PRIME ANY AREASSUBJECT TO MOISTURE 12

00m

m x

180

0, 2

400,

270

0, 3

000

7.5 & 9mm SHEET THICKNESSES AVAILABLE

1200mm

2400

mm

7.5or 9mm

RE

BA

TED

ED

GE

RE

BA

TED

ED

GE


STO/MONOTEK


FIBRE CEMENT SHEET INFORMATION

FCS 006

2017

SCALE 1:50


1. KEEP SHEETS DRY BEFORE USING.2. READ SPECIFICATIONS AND CHECK DRAWINGS, DETAILS, FRAMING, UNDERLAY, FLASHING TAPES, AND BLOCKING IS SATISFACTORY3. INSTALL STO PVC TRAY AND JOINERY FLASHING AS PER STO DETAILS (BUILDER TO SUPPLY ALUMINUM HEAD FLASHING WITH STOPENDS)4. CHECK LAYOUT AND INSTALL SHEETS VERTICALLY STARTING FROM BOTTOM PLATE5. STAGGER VERTICAL SHEET JOINTS TO AVOID CONTINUOUS JOINS6. SECURE SHEETS WITH FIXINGS AS PER MANUFACTURERS DETAILS7. MEASURE DISTANCES ACCURATELY TO AVOID NARROW IN FILLS OR GAPS

SAFE WORKING PRACTICE

1. HAVE SUFFICIENT PEOPLE TO LIFT SHEETS ON SITE2. WEAR PROTECTIVE CLOTHING, EYE AND EAR PROTECTION AND DUST MASK OR RESPIRATOR WHEN CUTTING OR SANDING3. USE A CIRCULAR SAW FITTED WITH A DIAMOND BLADE OR F/C SCRIBER AND HEPA VACUUM WHEN CUTTING4. CONTAIN CUTTING AREA TO MINIMIZE DUST - HEPA VACUUM UP RESIDUE5. PROVIDE SUITABLE ACCESS PLATFORMS, EQUIPMENT AND TOOLS TO CARRY OUT THE WORK6. COMPLY WITH HEALTH AND SAFETY REGULATIONS AND MAINTAIN FIRST AID EQUIPMENT AS PER THE LEGISLATION

HORIZONTAL CONTROL JOINTS AT INTER-STOREY JUNCTIONSOR AT 5400mm MAX. ON CONTINUOUS STUDS

VERTICAL CONTROL JOINTS - 5400mm MAX.CTRS OR ATDISSIMILAR MATERIAL

200

MIN.200mmOVERLAP

VERTICALCONTROL JOINTOR 200mmOVERLAP


STO/MONOTEK


SHEET LAYOUT

FCS 007

2017

N.T.S

SHEET JOINT 200mm MIN. FROMANY PARALLEL OPENINGS

1. SHEET JOINTS MUST NOT COINSIDE WITH JOINERY JAMB EDGES UNLESS ACONTROL JOINT IS TO BE FORMED

2. ALL SHEET EDGES SHALL LINE THROUGH AND BE SUPPORTED BY A FRAMINGMEMBER

3. LOCATE INTER-STOREY JOINTS AS PER BOARD MANUFACTURERSSPECIFICATIONS

4. STAGGER VERTICAL SHEET JOINTS AT INTER-STOREY JUNCTION5. HORIZONTAL CONTROL JOINTS AT INTER-STOREY JUNCTIONS

- 8mm VERTICAL CONTROL JOINTS AT 5.400M CTRS.MAX- INTER-STOREY DRAINED JOINTS EVERY THIRD FLOOR

VERTICAL CONTROLJOINT REQUIRED AT5.400M CTRS

INTER-STOREY CONTROLJOINT or FLASHING

STO PRE MESHEDCORNER ANGLE

STOARMAT MESHED JOINTING

STO GLASS MESH FOR STOARMATRENDER SYSTEM

SHEETS (sized to avoid infills)

H GRADE EPS SHEETS NORMALLY - 2700 x 1200mm

NOTE: USE FULL SHEETS WHERE POSSIBLEALL SHEET EDGES MUST BE SUPPORTED BY A FRAMING MEMBERALL SHEETS CUTS SHALL BE MADE CAREFULLY TO ACHIEVE A TIGHT BUTT FIT.

ANY GAPS IN THE EPS SHEET MUST BE FILLED WITH STO FOAM ON HORIZONTAL JOINTS CARE MUST BE TAKEN TO AVOID FOAM FILLING THE CAVITY


STO/MONOTEK


SHEET and SYSTEM LAYOUT

FCS 008

2017

SCALE 1:20

TIMBER FRAMINGTO NZS 3604

H3.1 TIMBER CAVITY BATTENS@ 300mm MIN.CTRS ON600mm FRAMING AS PERSHEET MANUFACTURERSDETAILS

STOARMAT uPVC CLIP ON FOOTTRAY. SHEET TO OVERHANGBOTTOM PLATE BY 50mm

WALL UNDERLAY MEETINGREQUIREMENTS E2/AS1

STOARMAT CLASSIC RENDER

CONCRETE FOUNDATION AS PER NZS3604 ORSPECIFIC ENGINEERING REQUIREMENTS

STOARMAT MESHED JOINT

STOLIT K & MP RANGECOLORED FINISHING RENDER

STO PUTZGRUND PRIMER

SELECTED REBATED EDGEFC SHEET

STO EUROPEAN MESH

1. FOR FIXING CENTERS REFER TO SHEETMANUFACTURERS SPECIFICATION

2. TIMBER FRAME MOISTURE CONTENTMUST NOT EXCEED 24% AT CLADDINGSTAGE

3. STOARMAT uPVC FLASHINGS AVALIABLEFOR BOTTOM TRAY, JOINERY & FINISHINGEDGES

VENTED VERMIN TRAY (byothers)

STOCOLOR MAXICRYLFACADE PAINT


STO/MONOTEK


STOARMAT RENDER SYSTEM - ISOMETRIC

FCS 100

2017

SCALE 1:5

OVERHANG RECOMMENDEDTO AVOID VARIANCES INFOUNDATION


DPC

INTERIOR LINING

50m

mC

lad.

AS PER NZS 3604:2011

DPM

6mm

CONCRETE SLAB/REINFORCINGAS PER NZS 3604 OR ENGINEERSPECIFIC DESIGN - NOT SHOWN

FOR CLARITY

20mm DRAINED & VENTEDCAVITY

7.5/9.0mm REBATED FIBRECEMENT SHEET

STO ARMAT RENDER SYSTEM

225m

m M

IN.

TO U

NP

AV

ED

GR

OU

ND

LE

VE

L

150m

m M

IN.

TO P

AV

ED

GL

uPVC VENT STRIP. MITRECORNERS & KEEP CLEAR OFDEBRIS

BATTENS AS PER SHEETMANUF. DETAILS

WALL UNDERLAY

STOARMAT CLIP ON FOOTTRAY

INSULATION AS PERNZBC - Clause H1

100m

m M

IN.

Sto

Ren

der

50m

mFl

exyl


STO/MONOTEK


FOUNDATION SLAB-ON-GROUND

FCS 200

2017


DPC

STO RENDER SYSTEMTO FOUNDATION

SCALE 1:5

INTERNAL LINING

WALL UNDERLAY

20mm DRAINED CAVITY


7.5/9.0mm REBATEDSHEET

BATTENS AS PER SHEETMANUF.DETAILS

50m

mC

lad.

DPM

AS PER NZS 3604

5

225m

m M

IN.

TO U

NP

AV

ED

GR

OU

ND

LE

VE

L

150m

m M

IN.

TO P

AV

ED

GL

CONCRETE SLAB/REINFORCINGAS PER NZS 3604 OR ENGINEERSPECIFIC DESIGN - NOT SHOWN

FOR CLARITY

uPVC VENT STRIP. MITRE CORNERS& KEEP CLEAR OF DEBRISSTOARMAT CLIP ON FOOTTRAY


STOFLEXYL WATERPROOFINGTO REBATE, CONTINUE TO50mm PAST STO RENDERTERMINATION POINT

100m

m M

IN.

Sto

Ren

der

50m

mFl

exyl


STO/MONOTEK


REBATED SLAB-ON-GROUND -RENDERED FINISH

FCS 201

2017

SCALE 1:5


DPC

INTERIOR LINING

50

6mm OVERHANG RECOMMENDED TOAVOID VARIANCES IN FOUNDATION

6

15

uPVC VENT STRIP. MITRE CORNERS& KEEP CLEAR OF DEBRIS


CAVITY BATTENS AS PER MANUF.DETAILS


7.5/9mm FIBRE CEMENT REBATEDSHEET AS PER MANUF. DETAILS

20mm DRAINED & VENTED CAVITYWALL UNDERLAY

NOTE:FOR CLEARANCE BETWEENCLADDING AND ADJACENTGROUND - REFER NZS3604:2011


STO/MONOTEK


CONCRETE FOUNDATION/TIMBER FLOOR

FCS 202

2017

225m

m u

npav

ed G

L

SCALE 1:5

CONCRETE FOOTING ASPER NZS 3604 OR ENGINEER

SPECIFIC DESIGN

CONCRETE SLAB/REINFORCINGAS PER NZS 3604 OR ENGINEER

SPECIFIC DESIGN

DPC

NOTE:SHELL OF BLOCK CAN SUPPORTBOTTOM PLATE WHEN SLAB ISTIED TO FOUNDATION

50m

m c

ladd

ing

150m

m to

pav

ing

GLINSULATION AS PERNZBC - Clause H1

DPM

WALL UNDERLAY

20mm DRAINED CAVITY

7.5/9.0mm REBATED SHEET



uPVC VENT STRIP. MITRECORNERS & KEEP CLEAROF DEBRIS

STOARMAT CLIP ON FOOT TRAY.


STO/MONOTEK


CONC.BLOCK FOUNDATION EDGE DETAIL

FCS 203

2017

SCALE 1:5

50m

m c

ladd

ing

150m

m to

pav

ing

225m

m u

npav

ed G

L


DPM

DPC10mm INSULATIONIF SPECIFIED

GL

CONCRETE SLAB/REINFORCINGAS PER NZS 3604 OR SPECIFIC

ENGINEER DESIGN (SED)

Var

ies

refe

r to

NZS

3604

or S

ED

WALL UNDERLAY

20mm DRAINED CAVITY


STOARMAT RENDERSYSTEM





STO/MONOTEK


SOLID CONC.FOUNDATION EDGE DETAIL

FCS 204

2017

50m

m c

ladd

ing

150m

m to

pav

ing

225m

m u

npav

ed G

L

DPC

GL

WALL UNDERLAY

20mm DRAINED CAVITY






RIBRAFT POLYSTYRENE PODINSTALLATION IN ACCORDANCETO FIRTH RIBRAFTCONSTRUCTION DETAILS

8522

0

CONCRETE SLAB/REINFORCINGAS PER NZS 3604, SPECIFIC

DESIGN OR ENGINEER (SED)Reinforcing not shown for clarity

300

SCALE 1:5


STO/MONOTEK


RIBRAFT FLOOR SYSTEM / EDGE DETAIL

FCS 205

2017

20mm DRAINED CAVITY

7.5/9.0mm REBATED SHEETSTOARMAT RENDER SYSTEM

BATTENS AS PER SHEET MANUF.DETAILSuPVC VENT STRIP. MITRE CORNERS &KEEP CLEAR OF DEBRIS


SCALE 1:10

1. CONCRETE SLAB/REINFORCING AS PER NZS 3604, SPECIFIC DESIGNOR ENGINEER (SED)

Reinforcing not shown for clarity2. WHERE INSULATION OS BELOW GROUND, APPLY TWO (2) COATS OF

STOFLEXYL TO MAXRAFT INSULATION BEFORE COMMENCING3. 150mm MIN. CLEARANCE FROM SLAB LEVEL TO EXTERIOR PAVING,

225mm MIN. CLEARANCE FROM SLAB LEVEL TO UNPAVED GROUND TOE2/AS1

4. LAP AN EIFS FLASHING TAPE MIN. 75mm ONTO DPM AT FOUNDATIONAND RETURN MIN. 50mm UP ONTO MAXRAFT FOUNDATION WALL.

SOLID COMPACTION800mm MIN. PAST EDGEOF FOUNDATION

100

100

50

250

10450

STOMULTI SCREED MESHED BASECOATFINISHED IN 1.0mm FLOAT or STOLIT KFINISHING RENDER, PAINTED INSTOCOLOR MAXICRYL

WALL UNDERLAY

50

REFER NOTE 4 BELOW


STO/MONOTEK


MAXRAFT FLOOR SYSTEM / EDGE DETAIL

FCS 206

2017

SCALE 1:2


20mm NOMINAL VERTICALCAVITY BATTENS

WALL UNDERLAY

1-2mm SHEET GAP12mm MIN12mm MIN


INSTALL SHEETS WITH A1-2mm GAP AT SHEET JOINT.

FIX SHEETS WITH HARDIESFIXINGS AS PER

MANUFACTURERS LAYOUTWITH FIXINGS MINIMUM

12mm FROM SHEET EDGES


STO/MONOTEK


VERTICAL SHEET JOINT

FCS 300

2017

SCALE 1:2


140mm VERTICAL TIMBERCAVITY PACKER AT 150mmMAXIMUM CENTRESBETWEEN TIMBER CAVITYBATTENS

WALL UNDERLAY

1-2m

m S

HE

ET

GA

P15

-20m

m15

-20m

m


INSTALL SHEETS WITH A1-2mm GAP AT SHEET JOINT.FIX SHEETS WITH HARDIESFIXINGS AS PERMANUFACTURERS LAYOUTWITH FIXINGS 15-20mmFROM SHEET EDGES

140X45 NOG ON EDGE OFFRAMING

THIS METHOD IS USED TO INSTALL FULL HEIGHT SHEETS WHERE THEWALL HEIGHT IS TALLER THAN THE STANDARD SHEET HEIGHT. THISMETHOD MUST NOT BE USED AT FLOOR JOISTS OR GABLE ENDS AS ACONTROL JOINT.

7.5/9/0mm REBATED SHEET


STO/MONOTEK


HORIZONTAL SHEET JOINT

FCS 301

2017

SCALE 1:2

WALL UNDERLAY


40x19mm H3.1 TIMBERCAVITY BATTENS

20mm DRAINED CAVITY

7.5/9.0mm REBATEDSHEET WITH RECESSEDEDGE AT CORNER

35m

m M

IN

40mm MIN

1-2mm GAP

STOARMAT MESHEDJOINT USING uPVCPREMESHED CORNERBEAD

MS SEALANT TO SHEETGAP


STO/MONOTEK


EXTERNAL CORNER

FCS 302

2017

SCALE: 1:2

WALL UNDERLAY CONTINOUSAROUND CORNERS

DOUBLE STUDREQUIRED

FOR CLADDING SHEETS -REFER MANUFACTURER FORSPECIFIC FIXING DETAILS

SELECTED SHEET FIXING,12mm FROM SHEET EDGE -AS PER MANUFACTURERSRECOMENDATIONS

uPVC 50x50mm CORNERFLASHING

8mm BETWEEN SHEETS,STOARMAT - FLUSH FINISH

STOARMAT RENDER SYSTEMDOUBLE MESHED IN CORNER

8mm GAP

12mm MIN



STO/MONOTEK


INTERNAL CORNER

FCS 303

2017

SCALE 1:2

NOTE: REMOVE CONTROL JOINT TAB CAREFULLY AS SOON AS ARMAT HASSET TO AVOID CRACKS IN THE SYSTEM.

VERTICAL CONTROL JOINTS AT 5.4M CTRS MAX.PREFERABLY ABOVE &BELOW JOINERY JAMB LINE.

INSTALL STO uPVC CONTROLJOINT WITH MS SEALANT INSTOARMAT MESH COAT

8



12mm MIN.12mm MIN.

50mm WIDE INSEALTAPE

WALL UNDERLAY

5.400M TO EXT.CNR OR NEXT CONTROL JOINT



STO/MONOTEK


VERTICAL CONTROL JOINT

FCS 304

2017

SCALE 1:2

WALL UNDERLAY - ENSUREUNDERLAY RUNS CONTINUOUSOVER JOINT

7.5/9.0mm REBATED SHEETIN ACCORDANCE WITHSHEET MANUFACTURERSDETAILS


NOMINAL 20x45mm H3.1TIMBER CAVITY BATTENS ASPER SHEET MANUF. DETAILS

HORIZ.uPVC CONTROL JOINTFLASHING (staple to batten)

DONOT SEAL BETWEENPROFILE AND SHEET

15

10m

m G

AP PREMESHED ARCHITECTURAL

PROFILE OVER INTER-STOREYJOINT - SUPPLIED & FIXED BYCONTRACTOR

7.5/9.0mm REBATED SHEETFIXED IN ACCORDANCE WITHSHEET MANUFACTURER



STO/MONOTEK


HORIZ.JUNCTION - NON DRAINING- OPT 1

FCS 305

2017

SCALE 1:2


7.5/9.0mm REBATED SHEETAS PER SHEETMANUFACTURERS DETAILS


HORIZONTAL CAVITY SPACERS

NOMINAL 20x45mm H3.1TIMBER CAVITY BATTENS ASPER SHEET MANF. DETAILS

10

10m

m G

AP

7.5/9.0mm REBATED SHEETIN ACCORDANCE WITHSHEET MANF. DETAILS


STO uPVC 12mmINTER-STOREY JOINT


STO/MONOTEK


HORIZ.JUNCTION - NON DRAINING- OPT 2

FCS 306

2017

20mm DRAINED CAVITY

FLASHING TAPE OVER

ALLOW TO RENDER BEHINDTHEN SEAL WITH MS SEALANTOR STO SEAL TAPE

1. AS REQUIRED TO LIMITCONTINUOUS CAVITYCONSTRUCTION TO TWOSTOREYS, FLASHING BACK ANDFRONT COVER TO BE A MINIMUM35mm EXCLUDING DRIP EDGES

2. IN EXTRA HIGH WIND ZONESINCREASE FLASHING COVER TO60mm MIN.AND USE A RIGIDUNDERLAY

SCALE: 1:2

MIN

.CO

VE

R

MIN

.CO

VE

R

35m

m

35m

m


7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF. DETAILS

20mm DRAINED CAVITY

FIX AS PER SHEET MANUF.DETAILSWALL UNDERLAY - ENSUREUNDERLAY RUNS CONTINUOUSOVER JOINT


uPVC VENT STRIP. MITRE CORNERS& KEEP CLEAR OF DEBRISSTO uPVC CLIPON FOOT TRAY

STOARMAT RENDER SYSTEM7.5/9.0mm REBATED SHEET

15° SLOPE TO INTER-STOREYFLASHING - REFER E2/AS1 FORFLASHING DURABILITY

15

15

MIN.GAP FORMOVEMENT

STO uPVC 6mm FINISHINGEDGE


STO/MONOTEK


HORIZONTAL JUNCTION - DRAINING

FCS 307

2017

100mm min.

SCALE 1:5

FLASHING TAPE

STAR CUT

CUT LINES

8/10mm SEALANT BEAD ON PEF RODBETWEEN PIPE AND PLASTER

PIPE OR OTHER PENETRATIONSLOPED DOWNWARDS

NOTE: INSTALL FLASHING TAPE WITH 100mm CLEARANCE AROUND PIPE ONTO WALLUNDERLAY AND WRAP 25mm ROUND PIPE.

WHERE MIN 75mm BLOCKING SUPPORTS THE WALL UNDERLAY AROUND THEPENETRATION THE FLASHING TAPE CAN BE OMITTED BUT A FACE FIXEDEXTERIOR FLANGE WITH SEALANT IS REQUIRED AS PER E2AS1 FIG.68

TIMBERFRAMING TO

NZS3604

WALL UNDERLAY

7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF. DETAILSSTOARMAT RENDERSYSTEM

CAVITY BATTENS

FLASHING TAPE


STO/MONOTEK


PIPE PENETRATION (up to 100mm) DETAIL

FCS-350

2017

CAVITY BATTENS

SCALE 1:2

WALL UNDERLAY

50 x 3mm EPDM WASHERGASKETS REQUIRED AROUNDFIXINGS AND PLATE TO PROVIDEWATERTIGHTNESSTIMBER PACKER SLOPED AT 5°50mm min CLEARANCE FROMCAVITY BATTENSTIMBER BLOCKING BETWEENSTUDS AS REQUIRED

ALL WIRING SHOULD BEENCLOSED IN CONDUIT

CABLES SLOPE OUT

7.5/9.0mm REBATED SHEET - FIXED INACCORDANCE WITH MANUF. DETAILSSTOARMAT RENDER SYSTEM


STO/MONOTEK


LIGHT FITTING/FIXING DETAIL

FCS 351

2017

SCALE 1:2

TAP FITTING ON EPDMRUBBER WASHER

PROVIDE TIMBERBLOCKING AT TAP

FLASHING TAPE100mm ONTO UNDERLAY25mm ONTO TAP CONNECTION

CAVITY BATTENS7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHMANUF. DETAILSSTOARMAT RENDER SYSTEM

WALL UNDERLAY


STO/MONOTEK


TAP FITTING/FIXING DETAIL

MCS 352

2017

SCALE 1:2

WALL UNDERLAY

7.5/9.0mm REBATED SHEET - FIXED INACCORDANCE WITH MANUF. DETAILSSTOARMAT RENDER SYSTEM

SELECTED HANDRAIL

TIMBER PACKER AT FIXINGSPOINTS - SLOPED AT 5DEGREES min. 50mmCLEARANCE FROM CAVITYBATTENS

NOTE: USE A FIXING PLATES ON HANDRAILS TO AVOID POINT LOADING

50 x 3 mm EPDM WASHER GASKETSREQUIRED AROUND FIXINGSBETWEEN PLATE AND RENDER TOPROVIDE WATERTIGHTNESS

TIMBER BLOCKINGBETWEEN STUDS ASREQUIRED

100mm MAX.NZBC D1 clause 1.5.2

20mm DRAINED CAVITY

INSTALL HANDRAIL PLATES OVER STORENDER SYSTEM


STO/MONOTEK


HANDRAIL BRACKET/FIXING DETAIL

FCS 353

2017

SCALE 1:2

METERBOX

WALL UNDERLAY RETURNEDINTO OPENING WITH FLASHINGTAPE 25mm ONTO METERBOX

88

INTERNAL LINING

TIMBER FRAMINGTO NZS3604

INTERNAL LINING


MS SEALANT OVER PEF BACKERROD TO PERIMETER OF METERBOX

STOARMAT uPVC CLIP ONTRAY - remove drip edge

8mm AIRSEAL ONPEF ROD BYBUILDER

8mm AIRSEAL ONPEF ROD BYBUILDER


METERBOX

CAVITY BATTEN WITH 50mm GAPFROM HORIZONTAL SLOPEDBATTEN AT BOTTOM JUNCTION

FLASHING TAPE OVER MIN.10° SLOPEDBATTEN ONTO WALL UNDERLAY

HORIZONTAL BATTEN SLOPED AT 10°INTO CAVITYSTOARMAT uPVC CLIP ONTRAY - remove drip edgeMS SEALANT OVER PEF BACKERROD TO PERIMETER OF METERBOX


7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHMANUF. DETAILS

WALL UNDERLAY

7.5/9.0mm MONOTEK SHEET

FLASHING TAPE SEALED TOMETERBOX AND WALL UNDERLAY


STO/MONOTEK


METERBOX - CROSS SECTION

FCS 354

2017

SCALE 1:2

uPVC OR OTHERDOWNPIPE -SIZE REFERNZBC E1 Table 5

SUITABLE BLOCKING ATA 5° SLOPE min 50mm

CLEARANCE FROMVERTICAL CAVITY

BATTENS

DOWNPIPE/CLIP -SADDLE @ 1.2MCTRS MAX.

MS SEALANT AROUND CONDUIT

CABLE/WIRING

PVC CONDUIT SLEEVE INSTALLEDAT 5 DEGREES DOWNWARDSLOPE TO MESH COAT.APPLICABLE TRADE TO ENSUREFINISHED INSTALLATION ISWATERTIGHT

1. DOWNPIPE/CLIP - SADDLE DETAIL

2. WIRING PENETRATION DETAILNOTE: ENSURE THE AMOUNT OF PENETRATIONS THROUGH THESYSTEM IS KEPT TO A MINIMUM. THE WEATHERSEALING OF ALL WIRING,ETC AS SHOWN, IS THE RESPONSIBILITY OF THE APPLICABLE TRADE


20mm DRAINED & VENTEDCAVITY7.5/9.0mm REBATED SHEET - FIXED INACCORDANCE WITH SHEET MANUF. DETAILSSTO ARMAT RENDER SYSTEM

WALL UNDERLAY



WALL UNDERLAY

7.5/9.0mm REBATED SHEET - FIXED INACCORDANCE WITH SHEET MANUF. DETAILS


STO/MONOTEK


DOWNPIPE SADDLE FIXING & WIRING DETAILS

FCS 355

2017

SCALE 1:2

EXTRACTION PIPE SLOPEDOWNWARDS AT MINIMUM 5°

FAN

CO

VE

R

TIMBER BLOCKING ASREQUIRED

NOTE:LEAVE 40mm DRAINAGE GAP IN SEALANT AT BOTTOM OF FAN COVER.INSTALL FLASHING TAPE 100mm AROUND PIPE ONTO WALL UNDERLAY AND WRAP25mm ROUND PIPE.FOR FLEXIBLE PIPES, TAPE PIPE TO FAN COVER, APPLY STO JOINT SEAL, TAPEAROUND TAPE BEFORE PLACING IN HOLE. ALWAYS FINISH RENDER BEFOREINSTALLING FAN COVER

TIMBER FRAMING ASPER NZS 3604

TIMBER BLOCKING ASREQUIRED

FLEXIBLE FLASHINGTAPE

MS SEALANT ALL ROUND,LEAVE 40mm DRAINAGEGAP AT BOTTOM

MS SEALANT/PEF RODAT PIPE JUNCTION (STOSEAL TAPE ON FLEXIBLEPIPES)

FLEXIBLE FLASHINGTAPE

20mm NOMINAL CAVITY BATTENS - ASPER SHEET MANUFACTURERS DETAILS


7.5/9.0mm REBATED SHEET - FIXEDAS PER SHEET MANUF. DETAILS

WALL UNDERLAY20mm NOMINAL CAVITY BATTENS -AS PER SHEET MANUF. DETAILS


STO/MONOTEK


FAN VENT DETAIL

FCS 356

2017

STOARMAT RENDER SYSTEMREBATED SHEET TO OVERHANG CAVITY CLOSER BY15mm min. FIT CLIP ON TRAY AND LEAVE 5mm min.CLEARANCE TO HEAD FLASHING1. PROPRIETARY ALUM. HEAD FLASHING TO COVER

WINDOW FACING BY 10mm SLOPED 15° WITH min.35mm UPSTAND TAPED TO WALL UNDERLAY.ALLOW HEAD FLASHING TO PASS JAMBS BY 20mmAND FIT STOP ENDS IN CAVITY. FLASHING TAPESYSTEM TO BE INSTALLED AROUND JOINERYOPENINGS AS PER E2/AS1 BY BUILDER.

2. IN EXTRA HIGH WIND ZONES INCREASE FLASHINGCOVER TO 60mm MIN. AND USE A RIGIDUNDERLAY

SCALE 1:2

TIMBER LINTEL ASPER NZS 3604

FLASHING TAPE ONTO WALLUNDERLAYVENTED CAVITY CLOSERmin. 15mm FROM TRAY

ALUMINIUM WINDOWHEAD FLASHING WITH 15°SLOPE AND 10mm COVERAT WINDOW HEAD

MIN. 5mm GAP REQUIRED

NOTE: SEALANT REQUIREDFOR VERY HIGH AND EXTRAHIGH WIND ZONESALUMINIUM WINDOWJOINERY

INTERIOR LINING

AIRSEAL ON PEF RODGAP 7.5-8mm APPROX

WALL UNDERLAY

7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF. DETAILSSTOARMAT RENDER SYSTEM

20mm DRAINED CAVITY*

25m

m35

15

5mm

GAP

* THIS DIMENSION MUSTBE CHECKED WITH

JOINERY MANUFACTURER

STO uPVC CLIP-ON FOOTTRAY


STO/MONOTEK


ALUMINIUM JOINERY - HEAD DETAIL

FCS 400

2017

SCALE 1:2

JOINERY SUPPORT BARREQUIRE FOROPENINGS OVER 600mm

1. PROVIDE 6mm MIN.FILLET BEAD OF MS SEALANT TO JAMBS & SILL2. BUILDER TO INSTALL FLASHING TAPE TO CORNERS & SILL OVER WALL UNDERLAY3. POSITION WINDOW OFF BOARD BY 2-3mm TO ALLOW FOR STOARMAT JAMB & SILL

FLASHINGS

WARNING: SOME BRANDS OF ALUMINIUM JOINERY HAVE DRAINAGE VENTS IN THE BOTTOM EDGE OF THE SILL FLANGE.ENSURE DRAINAGE VENTS REMAIN CLEAR.

PROPRIETARY ALUM.WINDOW JOINERY



VERTICAL CAVITYBATTENS

FRAME BLOCK


AIRSEAL ON PEF ROD GAP7.5-8mm APPROX.

INTERIOR LINING

WALL UNDERLAY RETURNEDINTO OPENINGS & FLASHING

TAPE CONTINUOUS ALONGSILL MIN 100mm UP JAMBS &50mm ONTO FACE OF WALL

UNDERLAY

MS SEALANT

STOARMAT uPVC SILLFLASHING

REMOVE FLASHING TEARTAB & APPLY MS SEALANT



STO/MONOTEK


ALUMINIUM JOINERY - SILL DETAIL

FCS 401

2017

SCALE 1:2

ALUMINIUMWINDOW JOINERY

FLASHING TAPE(100mm UP JAMBS)

H1.2 PACKER TOSUPPORT JOINERY

INTERNAL LINING


MS SEALANT TO JAMBS


LINE OF HEAD FLASHINGOVER WITH STOPEND

1. PROVIDE 6mm MIN.FILLET BEAD OF MS SEALANT TO STOARMAT JAMB & SILL FLASHING2. BUILDER TO INSTALL FLASHING TAPE TO OPENINGS OVER WALL UNDERLAY AS PER E2/AS13. POSITION WINDOW OFF BOARD BY 2-3mm TO ALLOW FOR STOARMAT JAMB & SILL FLASHING


WALL UNDERLAY7.5/9.0mm REBATED SHEET - FIXED IN

ACCORDANCE WITH SHEET MANUF. DETAILSCAVITY BATTENS

STOARMAT uPVC JAMBFLASHING GLUE OR BED

FLASHING IN PLACE BEFORERENDERING

5 10mmMIN.COVER

LINE OF HEAD FLASHING20mm MIN.PAST JAMB



STO/MONOTEK


ALUMINIUM JOINERY - JAMB DETAIL

FCS 402

2017

SCALE 1:2

ALUMINIUM WINDOW/DOORJOINERYMS SEALANT

WALL UNDERLAY

STO uPVC JAMB FLASHING GLUEOR BED FLASHING IN PLACEBEFORE RENDERING

AIRSEAL ON PEF ROD,GAP 7.5-8mm APRROX.

FLASHING TAPE (100mmUP JAMBS)


LINE OF HEAD FLASHINGOVER WITH STOPEND

7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF. DETAILSSTOARMAT RENDER SYSTEM


STO/MONOTEK


INT.CNR ALU.WINDOW/DOOR JOINERY - JAMB DETAIL

FCS 403

2017

SCALE 1:5


WALL UNDERLAY

FLASHING TAPE OVER HEADFLASHING ONTO WALL UNDERLAYuPVC VENT STRIP

ALUMINIUM WINDOW HEAD FLASHINGTO EXTEND 20mm MIN.PAST JAMBSWITH 15° SLOPE AND 10mm COVER ATWINDOW HEAD


SEALANT REQUIRED FOR VERY HIGHAND EXTRA HIGH WIND ZONESALUMINIUM DOOR JOINERY

AIRSEAL ON PEFROD GAP 7.5-8mmAPPROX

5


STO uPVC CLIP-ON FOOT TRAY


STO/MONOTEK


ENTRY DOOR HEAD DETAIL

FCS 404

2017

SCALE 1:5

50

ALU.OPEN INDOOR JOINERY

LINE OF STOARMAT RENDERSYSTEM BEYOND - SHOWNDASHED

TURN UP FLASHING TAPE100mm MIN.AT TRIMMERSTUDS 10

0

NOTE:FOR CLEARANCE BETWEENCLADDING AND ADJACENT GROUND- REFER NZS3604:2011


STO/MONOTEK


ENTRY DOOR THRESHOLD DETAIL

FCS 405

2017

SCALE 1:5

AIRSEAL ON PEF ROD GAP7.5-8mm APPROX & PACKER

WALL UNDERLAY LAPPED &STAPLED ON INSIDE EDGE.FLASHING TAPE OVER AS PERE2/AS1 100mm UP JAMBS

DRESSED PINE PRIMED REVEALS& ARCHITRAVES

7.5/9.0mm REBATED SHEET -FIX IN ACCORDANCE WITH

SHEET MANUF. DETAILSSTOARMAT RENDER

SYSTEM

STO uPVC JAMB FLASHING

ALUMINIUM DOORJOINERYMS SEALANT

CAVITY BATTEN

WALL UNDERLAY

LINE OF HEAD FLASHING20mm MIN.PAST JAMBS -SHOWN DASHED


STO/MONOTEK


ENTRY DOOR JAMB DETAIL

FCS 406

2017

SCALE 1:5


TAPE AT CORNERS

ALU.SLIDING DOORJOINERY

AIRSEAL ON PEF ROD GAP7.5-8mm APPROX

FLASHING TAPE OVER HEADFLASHING ONTO WALL UNDERLAY

ALUMINUM HEAD FLASHING TO EXTEND20mm MIN.PAST JAMBS WITH 15° SLOPEAND 10mm COVER AT DOOR HEADSEALANT REQUIRED FOR VERY HIGHAND EXTRA HIGH WIND ZONES

5

uPVC VENT STRIP. MITRE CORNERS& KEEP CLEAR OF DEBRISSTOARMAT CLIP ON FOOT TRAY

WALL UNDERLAY20mm DRAINED & VENTED CAVITY7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF. DETAILSSTOARMAT RENDER SYSTEM

100mm LONG HORIZONTAL BATTENBEYOND

MIN.5mm GAP REQUIRED


STO/MONOTEK


SLIDING DOOR HEAD DETAIL

FCS 407

2017

SCALE 1:5

ALU.SLIDINGDOOR JOINERY

LINE OF STOARMATRENDER SYSTEMBEYOND - SHOWNDASHED50

TURN-UP FLASHING TAPE 100mmMIN.AT TRIMMER STUDS

100



STO/MONOTEK


SLIDING DOOR THRESHOLD - CONCRETE FLOOR

FCS 408

2017

SCALE 1:5

5020

6mm MIN.OVERHANG




STOARMAT RENDER

MS SEALANTSTO uPVC SILL & JAMBFLASHING


100mm DRAPE TODOUBLE-SIDED PERFORATED

FOIL INSULATION R = 0.9 -REFER NZBC - Clause H1


STO/MONOTEK


SLIDING DOOR THRESHOLD - TIMBER FLOOR

FCS 409

2017

SCALE 1:5


WALL UNDERLAY LAPPED &STAPLED ON INSIDE EDGE.

FLASHING TAPE OVER AS PERE2/AS1 100mm UP JAMBS

AIRSEAL ON PEFBACKING ROD TO ALLSIDES OF DOOR

CAVITY BATTENSuPVC STO JAMB FLASHING

7.5/9.0mm REBATEDSHEET - FIXED INACCORDANCE WITHSHEET MANUF. DETAILS

MS SEALANT



STO/MONOTEK


SLIDING DOOR JAMB DETAIL

FCS 410

2017

SCALE 1:5


TAPE AT CORNERS

ALU.BIFOLD (open - in)DOOR JOINERY

AIRSEAL ON PEF ROD GAP7.5-8mm APPROX

FLASHING TAPE OVER HEADFLASHING ONTO WALL UNDERLAY

ALUMINUM HEAD FLASHING TO EXTEND20mm MIN.PAST JAMBS WITH 15° SLOPEAND 10mm COVER AT DOOR HEADSEALANT REQUIRED FOR VERY HIGHAND EXTRA HIGH WIND ZONES

5


WALL UNDERLAY20mm DRAINED & VENTED CAVITY7.5/9.0mm REBATED SHEET - FIXED INACCORDANCE WITH SHEET MANUF.DETAILSSTOARMAT RENDER SYSTEM

CAVITY BATTENS - AS PER MANUF.DETAILS

MIN.5mm GAP REQUIRED


STO/MONOTEK


BIFOLD DOOR HEAD DETAIL

FCS 411

2017

SCALE 1:5

ALU.BIFOLD (open -in) DOOR JOINERY

50

LINE OF STOARMAT RENDERSYSTEM BEYOND - SHOWNDASHED

100

TURN-UP FLASHINGTAPE 100mm MIN.AT

TRIMMER STUDS



STO/MONOTEK


BIFOLD DOOR THRESHOLD - CONCRETE FLOOR

FCS 412

2017

SCALE 1:5

5020

6mm MIN.OVERHANG

20mm DRAINED & VENTED CAVITY -AS PER SHEET MANUF. DETAILS

uPVC VENT STRIP. MITRE CORNERS& KEEP CLEAR OF DEBRIS

STOARMAT CLIP ON FOOT TRAY


MS SEALANTSTO uPVC SILL & JAMBFLASHING

ALU.BIFOLD (open -in) DOOR JOINERY

TURN-UP FLASHINGTAPE 100mm MIN.AT

TRIMMER STUDS

100


100mm DRAPE TODOUBLE-SIDED PERFORATED

FOIL INSULATION R = 0.9 -REFER NZBC - Clause H1


STO/MONOTEK


BIFOLD DOOR THRESHOLD - TIMBER FLOOR

FCS 413

2017

SCALE 1:5

ALU.BIFOLD (open - in)DOOR JOINERY

WALL UNDERLAY LAPPED &STAPLED ON INSIDE EDGE.

FLASHING TAPE OVER AS PERE2/AS1 100mm UP JAMBS

AIRSEAL ON PEFBACKING ROD TO ALLSIDES OF DOORCAVITY BATTENS

uPVC STO JAMB FLASHING(to be fixed before battens)

7.5/9.0mm REBATEDSHEET - FIXED INACCORDANCE WITHSHEET MANUF. DETAILS

MS SEALANT


MS SEALANT


STO/MONOTEK


BIFOLD DOOR JAMB DETAIL

FCS 414

2017

SCALE 1:5

LINE OF STOARMAT RENDERSYSTEM - SHOWN DASHED

SELECTED ALU.ENTRYDOOR JOINERY

DRAINAGE CHANNELFALL ALONG LENGTH

TO OUTLET

REMOVABLECHANNEL COVERCHANNEL COVERSUPPORT BRACKETS

SELECTED FLOORFINISH

FLASHING TAPE TAPE OVER SILL ANDMIN. 100mm UP FRAME FINISH AT

BOTTOM EDGE OF SILL SUPPORT BAR

100

NOTEREFER TO E2/AS1 FIG. 17 A,B,C & D INCLUDING SECTION 9.1.10

150

12

12m

m M

AX

.

200mm MIN.

WANZ SUPPORT BAR WITHVENTILATION/DRAINAGE HOLESINSTALLED TO MANUFACTURERSRECOMMENDATIONSUNDER DOOR TRIM BY BUILDER

FLASHING TAPE

CONTINUOUSAIR SEAL


STO/MONOTEK


LEVEL ENTRY THRESHOLD DETAIL

FCS 415

2017

SCALE 1:2


WALL UNDERLAY

ADDITIONAL LAYER OFFLASHING TAPE LAPPEDOVER HEAD FLASHING

20mm DRAINED CAVITY

VENTED VERMINTRAY min. 15mm UP

STO uPVC CLIP-ONFOOT TRAY

ALUMINIUM HEADFLASHING WITH 15°SLOPE AND 10mm COVER

MIN. 5mm GAPREQUIRED

5

10

FLEXIBLE FLASHING TAPEINSTALLED OVER WALL

UNDERLAY AT CORNERS

10

1. HEIGHT WORK TO UNDERSIDE SOFFIT.MEASURE DOOR HEIGHT ON SITE &CHECK GARAGE DOOR SPECIFICATIONSFOR INTERNAL CORNER REQUIREMENTS

2. SEAL FLASHING FOR VERY HIGH orEXTRA HIGH WIND ZONES

3. IN EXTRA HIGH WIND ZONES INCREASEFLASHING COVER TO 60mm AND USE ARIGID UNDERLAY

7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF. DETAILSSTOARMAT RENDERSYSTEM


STO/MONOTEK


GARAGE DOOR - TIMBER HEAD

FCS 416

2017

SCALE 1:2

SELECTEDGARAGE DOOR

FLASHING TAPE OVERWALL UNDERLAY TOCORNERS OF OPENINGSPRE PRIMED H3.1JAMB LINER

10

REBATE IN GARAGE FLOORTO SUIT GARAGE DOOR

NOTE:MEASURE DOOR HEIGHT ON SITE & CHECK GARAGE DOORSPECIFICATIONS FOR INTERNAL CORNER REQUIREMENTS

MS SEALANT ONSTO JOINT SEALTAPE OR PEF ROD

6

WALL UNDERLAY20mm DRAINED

CAVITY


7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITH


SYSTEM


STO/MONOTEK


GARAGE DOOR - TIMBER JAMB

FCS 417

2017

10

SCALE 1:2

5mm MIN.GAPFC SHEET TO FINISH 10mmMIN.PAST TO FORM DRIPEDGE

GARAGE DOOR TRIM -REFER TO GARAGE DOOR

MANUFACTURERSRECOMENDATIONS

NOTE:MEASURE DOOR HEIGHT ON SITE & CHECKGARAGE DOOR SPECIFICATIONS FORINTERNAL CORNER REQUIREMENTS

FIBRE CEMENT SOFFIT -STOARMAT RENDER


PURPOSE MADE METALFLASHING

WALL UNDERLAY20mm DRAINED CAVITY

VENTED VERMINTRAY min. 15mm UP

7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF.DETAILSSTOARMAT RENDERSYSTEM


STO/MONOTEK


GARAGE DOOR - RENDER HEAD DETAIL

fcs 418

2017

SCALE 1:2

SELECTED GARAGE DOORGARAGE DOOR TRIM

HEIGHT WORK TO UNDERSIDE OFSOFFIT. INSTALL TOMANUFACTURERS INSTRUCTIONS

STO CAVITY BATTENS

REBATE IN CONC.SLAB TOSUIT GARAGE DOOR

7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHSHEET MANUF.DETAILS

STO PREMESHED CORNERBEAD OR S/S CNR ANGLE

FLASHING TAPE OVERWALL UNDERLAY TOCORNERS OF OPENINGS



STO/MONOTEK


GARAGE DOOR - RENDER JAMB DETAIL

FCS 419

2017

SCALE 1:5

FINISH SHEETS TO TOP EDGE

1. INSTALL METAL SADDLE FLASHING AT WALL JUNCTION2. ENSURE TOP IS TEMPORARILY WATERPROOFED BEFORE RENDERING3. METAL CAPPING EXCLUDING DRIP EDGE MUST OVERLAP SHEET BY

50mm MIN.IN LOW, MED or HIGH WIND ZONE,70mm MIN.IN VERY HIGH,90mm MIN.IN EXTRA HIGH WIND ZONES

4. INSTALL METAL CAPPING TO ALL ROOF PARAPETS

VA

RIE

S

VA

RIE

S

PROVIDE SEPARATION (ROOFUNDERLAY) TO METALCAPPING AND TIMBER

PRE FINISHED METAL CAPPINGTO PARAPET

5°5° MIN.FALL TO TOP OFPARAPET

STO JOINT SEAL TAPE ORSIMILAR TO CLOSE GAPS

9mm MIN.H3 PLYPACKED TO A FALL

WALL UNDERLAY CONTINUOUSOVER TOP OF WALL FRAME


7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITH

SHEET MANUF. DETAILS

20mm DRAINEDCAVITY


STO/MONOTEK


PARAPET/METAL FLASHING DETAIL

FCS 500

2017

10°

NOTE:STO FLEXYL MESHED WATERPROOFING MEMBRANE HAS BEENTESTED BY BRANZ TO MEET THE REQUIREMENTS OF AS/NZS4858

WATERPROOF MEMBRANE AS REQUIRED BY E2/AS1

EXTRA HIGH WIND ZONES REQUIRE A RIGID UNDERLAY.

SCALE 1:5

OVERLAY OF STO FLEXYL MESHEDWATERPROOFING UNDER MESHCOAT TO TOP & SIDES, 75mmMIN.DOWNTURN

STO PREMESHED PVC ADJUSTABLECORNER ANGLES



SHEET MANUF. DETAILS


20mm DRAINED CAVITY

10° MIN.FALL TO TOP OFPARAPET

H3.1 TIMBER PACKER CUT TOFALL, WITH ROOF UNDERLAY or

FLASHING TAPE


STO/MONOTEK


RENDERED PARAPET/BALUSTRADE DETAIL

FCS 501

2017

SCALE 1:5

WINDOW TRIMMINGSTUD

40mm MIN.40mm MIN.

150mm MIN.

TO FACE OF WINDOWOR DOOR JAMB STUD



SYSTEM

20mm DRAINED CAVITY WALL UNDERLAY LAPPEDAROUND CORNER

DRAIN FORMED INCORNER50x50mm CORNER FLASHINGS


STO/MONOTEK


PARAPET and/or ENCL.BALUSTRADE TO WALL - PLAN

FCS 502

2017

SCALE 1:5

WALL UNDERLAYWALL FRAMING

50x50mm BACKFLASHING

CAVITY BATTENS

9mm MIN.H3 PLYPACKED TO A FALL9mm MIN.H3 PLYPACKED TO A FALL


STO/MONOTEK


FLEXIBLE FLASHING INSTALL - ISOMETRIC

FCS 503

2017

SCALE 1:5

LINE OF METAL SADDLEFLASHING BEHIND FIBRECEMENT CLADDINGRIVET THROUGH SEALANT

50x50mm CNR FLASHINGBEHIND CLADDING EXTENDEDTO BOTTOM OF WALL SHEETSON EACH BUILDING FACE

2 LINES OF SEALANT CAPPINGTO SADDLE FLASHING

WALL UNDERLAY


9mm MIN.H3 PLYWOODTIMBER PACKER

CAPPING FLASHING

NOTE:LEAVE A 10mm GAP BETWEEN SADDLE FLASHING AND CAPFLASHING AT WALL TO ALLOW FOR EXPANSION AND SEAL WITHSEALANT UNDER CAP.


STO/MONOTEK


METAL SADDLE FLASHING & CAP INSTALL - ISOMETRIC

FCS 504

2017

SCALE 1:5


APPLY STOFLEXYL MESHED WATERPROOFING OVER JOINTEDREBATED SHEETS. STOFLEXYL MESHED WATERPROOFING HASBEEN TESTED BY BRANZ TO MEET THE REQUIREMENTS OFAS/NZS4858 FOR A WATERPROOFING MEMBRANE AS REQUIRED BYE2/AS1

OVERLAY OF STOFLEXYL MESHEDWATERPROOFING UNDERSTOARMAT MESH COAT TO TOP &SIDES 75mm MIN.DOWNTURN

H3.1 TIMBER CAVITYBATTENS AS PER SHEETMANUF.DETAILS

H3.1 TIMBER PACKER CUTTO A FALL - MIN.10°


STO/MONOTEK


STOFLEXYL MESHED SADDLE FLASHING - ISOMETRIC

FCS 505

2017

SCALE 1:5


APPLY STOFLEXYL MESHED WATERPROOFING OVER JOINTEDREBATED SHEETS. STOFLEXYL MESHED WATERPROOFING HASBEEN TESTED BY BRANZ TO MEET THE REQUIREMENTS OFAS/NZS4858 FOR A WATERPROOFING MEMBRANE AS REQUIRED BYE2/AS1

75

75

OVERLAY OF STOFLEXYL MESHEDWATERPROOFING UNDERSTOARMAT MESH COAT TO TOP &SIDES 75mm MIN.DOWNTURN

H3.1 TIMBER CAVITYBATTENS AS PER SHEETMANUF.DETAILS

H3.1 TIMBER PACKERCUT TO A FALL - MIN.10°


STO/MONOTEK


STOFLEXYL MESHED WATERPROOF CAPPING - ISOMETRIC

FCS 506

2017

SCALE 1:5

20mm DRAINED CAVITY

10°

NOTE:HANDRAIL REQUIRED WHERE BALUSTRADE IS UNDER1000mm

SELECTED MEMBRANE FINISHOVER H3 "C" FACED PLYWOODLAID TO 1:40MIN.FALL. GLUE &SCREW TO TIMBER JOISTS, ALLEDGES SUPPORTED ON TIMBER

20mm MIN.ANGLE FILLET

7.5/9.0mm REBATED SHEET - INSTALLAS PER MANUFACTERERS DETAILS


150m

m M

IN.

ME

MB

RA

NE

UP

STA

ND

3515

OVERLAY OF STO FLEXYL MEMBRANEUNDER MESH COAT TO TOP & SIDES,

75mm MIN.DOWNTURN

STO PREMESHED PVC ADJUSTABLECORNER ANGLES IN STO ARMAT

CLASSIC COAT

STO uPVC CLIP-ON FOOT TRAY.

MEMBRANE TO RUN UP150mm MIN.AFFLMEMBRANE REINFORCING STRIPVENTED CAVITY BASECLOSER


10° MIN.FALL TO TOP OFBALUSTRADE

H3.1 TIMBER PACKER or 9mmMIN.PLYWOOD - CUT TO FALLMIN.10°

20mm DRAINED CAVITY

7.5/9.0mm REBATED SHEET -INSTALL AS PER MANUF. DETAILS


35mm MIN. TO FINISHED LEVEL OFDECK/ROOF


STO/MONOTEK


BALUSTRADE/ENCLOSED DECK DETAIL

FCS 507

2017

SCALE 1:5

NOTE: - 100mm MIN. FROM FLOOR LEVEL FOR ENCLOSED DECKS - MIN.FALLS: 1:40 FOR DECKS, 1:30 FOR ROOFS & 1:100 FOR GUTTERS - ALLOW FOR TILES IF REQUIRED

3515

0

WALL UNDERLAY

STO uPVC CLIP-ON FOOTTRAY

MEMBRANE TO RUN UP150mm MIN.

MEMBRANEREINFORCING STRIP SELECTED MEMBRANE FINISH OVER H3

"C" FACED PLYWOOD LAID TO A 1:40 MIN.FALL. GLUE , SCREW TO TIMBER JOISTSALL EDGES SUPPORTED ON TIMBER.20mm MIN.ANGLE FILLET

20mm DRAINED CAVITY

7.5/9.0mm REBATED SHEET - INSTALLAS PER MANUFACTERERS DETAILS


VENTED CAVITY CLOSER


STO/MONOTEK


ENCLOSED DECK CROSS SECTION

MFCS 508

2017

35

SCALE 1:5

FLOORING

MS SEALANT TO TOPAND SIDES

LINE OF CANTILEVER JOIST -SHOWN DASHED

SOLID BLOCKINGBETWEEN JOISTS AS

REQUIRED

5mm MIN. GAP BETWEENRENDER SYSTEM AND

SADDLE FLASHING

5

5

35

MIN.COVER

12

12mm MAX.DRAINAGE

CONTINUOUS INTER-STOREYFLASHING

LINE OF CLADDING BETWEENJOISTS - SHOWN DASHED,CUT AROUND JOIST

CLADDING BELOW DECK

NOTE:REFER E2/AS1 Fig.16 FOR FLASHING REQUIREMENTS. PROVIDE 6-8mmWIDE SEALANT JOINT AT CLADDING/SADDLE FLASHING JUNCTION.

50mm MIN. SET DOWN FROM FLOOR OR THRESHOLD FORCANTILEVERED SLATTED DECKS

7.5/9.0mm REBATED SHEET20mm DRAINED CAVITYWALL UNDERLAY



STO/MONOTEK


CANTILEVERED SLATTED DECK

FCS 509

2017

SCALE 1:5

FINISHED DECK SURFACE


INTERNAL LINING

INSULATION TOEXTERIOR WALLS

FLOORING

FLOOR JOIST

12

M12 BOLTS - FIX AS PERPROJECT DETAILS


20mm DRAINED CAVITYWALL UNDERLAY

50mmØ x3mm EPDMWASHERS AROUND FIXINGS

H3.2 STRING - REFER NZS3604FOR SIZEH3.2 PACKER


STO/MONOTEK


NON CANTILEVERED SLATTED DECK

FCS 510

2017

SCALE 1:5

50

DECKING

DECK JOIST

FLOORING

FLOOR JOIST

6mm OVERHANGRECOMMENDED TO AVOID

VARIANCES IN FOUNDATION

12mm MIN.GAP

6

uPVC VENT STRIP. MITRE CORNERS& KEEP CLEAR OF DEBRISSTOARMAT CLIP ON FOOTTRAY

CAVITY BATTENS AS PER MANUF.DETAILS


9mm FIBRE CEMENT REBATED SHEETAS PER MANUF. DETAILS

20mm DRAINED & VENTED CAVITYWALL UNDERLAY


STO/MONOTEK


INDEPENDENT SLATTED DECK

FCS 511

2017

SCALE 1:2

12mm MIN.

SCALE 1:2

DOUBLE MS SEALANT BRACKET FCS AND AGAIN AT BRACKET/MESHCOAT TRANSITIONS

NOTE: CARPENTER MUST FIT SHEET NEATLY WITH 8mm GAP

TIMBER BEAM

TIMBER FRAMINGAS PER NZS 3604



FLASHING TAPE 100MM ONTO WALLUNDERLAY 25MM ONTO BRACKETMS SEALANT ALL ROUND

GALVANIZED OR STAINLESSSTEEL L BRACKET ENGINEEREDFOR LOAD

NOTE: 'L' BRACKET ENGINEERED FOR LOAD. FLASHING TAPE TOBUILDING UNDERLAY IN ACCORDANCE WITH E2/AS1 FIG. 68

7.5/9.0mm REBATED SHEET - FIX INACCORDANCE WITH SHEET MANUF.DETAILS


STO/MONOTEK


TIMBER BEAM / PERGOLA DETAIL

FCS 512

2017

SCALE 1:5

7525

A

A

EPDM WASHERS REQUIRED AROUNDFIXINGS AND PLATE TO PROVIDEWATERTIGHTNESS

RWH HEAD FIXED DIRECTLY ABOVE &BELOW SCUPPER PENETRATION

PRE FINISHED 0.55MM BMTSTEEL CUSTOM FOLDED ANDRIVETED RAIN WATER HEAD

MS SEALANT AROUNDOPENING/RHW FINISHED TOSTO FINISHING EDGE

MEMBRANE DRESSED OVER50x50mm ALU.ANGLE REBATEDINTO SUBSTRATE

50mm LIP

2550

50

SECTION A - A

200mm MIN.OUTLET THROUGH WALL

SELECTED MEMBRANE FINISHOVER H3 "C" FACED PLYWOODLAID TO 1:60MIN.FALL. GLUE &SCREW TO TIMBER JOISTS, ALLEDGES SUPPORTED ON TIMBER

20mm MIN.ANGLE FILLET

OUTLET THROUGH WALL

LINE OF MEMBRANELAPPED 50mm MIN.BEHINDWRAP UNDER CLADDING

LEAF GUARD


STO/MONOTEK


RWH/SCUPPER OPENING

FCS 513

2017

6mm MIN.

SCALE 1:10

NOTE:

IF BLOCKING IS MISSING, STAPLE WALL UNDERLAY TO SOFFITPLATE TO AVOID ANY VENTILATION GAPS

REFER TO E2/AS1 TABLE 1 FOR RISK LEVELS. EAVE FLASHINGREQUIRED WHEN FASCIA IS 100mm OR LESS FROM WALLCLADDING AND ROOF SLOPE IS LESS THAN 10° OR WIND ZONESARE VERY HIGH OR EXTRA HIGH

H3.1 PRE PRIMED &PAINTED FASCIA BOARD

PREFINISHED METALROOFING OVER ROOFUNDERLAY

PREFABRICATED TRUSSTOP CHORD OVERHANG

VARIES

MS SEALANT 6-8mm(before rendering)

SOFFIT LINING TOCLOSE OFF CAVITY


WALL UNDERLAY


20mm DRAINED CAVITY


STO/MONOTEK


FLAT SOFFIT/WALL JUNCTION

FCS 600

2017

SCALE 1:10


PREFINISHED METAL ROOFINGOVER ROOF UNDERLAYPREFABRICATED TRUSSTOP CHORD OVERHANG

VARIES

MS SEALANT 6-8mm(before rendering)


WALL UNDERLAY

7.5/9.0mm REBATED SHEET -FIXED IN ACCORDANCE WITHMANUF. DETAILS

20mm DRAINED CAVITY

SOFFIT LINING TOCLOSE OFF CAVITY

NOTE: REFER TO E2/AS1 TABLE 1 FOR RISK LEVELS. EAVEFLASHINGS REQUIRED WHEN FASCIA IS 100mm OR LESS FROMWALL CLADDING AND ROOF SLOPE IS LESS THAN 10° OR WINDZONES ARE HIGH OR VERY HIGH


STO/MONOTEK


RAKING SOFFIT/WALL JUNCTION

MFCS 601

2017

SCALE 1:10

MS SEALANT 6-8mm ON PEF ROD(over finished render)

NOTE:

REFER TO E2/AS1 TABLE 1 FOR RISK LEVELS. EAVE FLASHINGSARE REQUIRED WHEN FASCIA IS 100mm OR LESS FROM WALLCLADDING AND ROOF SLOPE IS LESS THAN 10°


PREFINISHED METALROOFING OVER ROOFUNDERLAY

PREFABRICATED TRUSSTOP CHORD

50mm MIN.FASCIA COVER OVERRENDER SYSTEM

PRE FINISHED METAL E2 EAVES FLASHING,LAP 125mm MIN. UNDER ROOF CLADDING,TURN DOWN INTO GUTTER

50

BLOCKING TO CLOSE OFF CAVITYFROM ROOF SPACE

125


7.5/9.0mm REBATED SHEET FIXED INACCORDANCE WITH MANUF. DETAILSSTOARMAT RENDER SYSTEM


STO/MONOTEK


FACE FIXED FASCIA

FCS602

2017

SCALE 1:5

SELECTED FIBRECEMENT SOFFIT LINING

PREFINISHED METAL ROOFINGOVER ROOF UNDERLAY

HEMMED METAL FLASHING

6mm MAX.GAP WITH MSSEALANT

NOTE:

MAX.ANGLE OF SOFFIT RESTRICTEDTO BETWEEN 91°-115°

SOFFITS ARE TO BE FIXED AFTERCLADDING

6


WALL UNDERLAY

7.5/9.0mm REBATED SHEET FIXED INACCORDANCE WITH MANF. DETAILS

20mm DRAINED CAVITY

50

35m

m c

over


STO/MONOTEK


RAKING SOFFIT (REVERSED)

FCS 603

2017

SCALE 1:5

SELECTED FIBRECEMENT SOFFIT LINING

PREFINISHED METAL ROOFINGOVER ROOF UNDERLAY

STO uPVC ADHESIVE SILLAND JAMB FLASHINGFINISH WITH MS SEALANT

NOTE:

MAX.ANGLE OF SOFFIT RESTRICTEDTO BETWEEN 91°-115°


WALL UNDERLAY

7.5/9.0mm REBATED SHEET -FIX IN ACCORDANCE WITHMANUF. DETAILS

20mm DRAINED CAVITY

6


STO/MONOTEK


RAKING SOFFIT - STO uPVC CONTROL JOINT

FCS 604

2017

SCALE 1:2

15

5mm MIN.GAP SELECTED FIBRE CEMENTSOFFIT - STOARMAT RENDERSYSTEM WITH STO FINISHINGEDGE

E2/AS1 COMPLIANTFLASHING

STO uPVC FOOT TRAY

FLASHING TAPE OVER VERMINON TO WALL UNDERLAY


7.5/9.0mm REBATED SHEET -FIX AS PER MANUF. DETAILS

WALL UNDERLAY


STO/MONOTEK


SOFFIT TO CLADDING DETAIL

FCS 605

2017

FASCIAEAVE SOFFIT

BUILDING UNDERLAY


NOMINAL H3.1 20x45mmTIMBER CAVITY BATTENSFLASHING TAPE OR

BUILDING UNDERLAYOVER FLASHING

APRON FLASHING WITH TAPEREDSTOPEND TO DIVERT WATER INTOGUTTER. FC SHEET TO BECAREFULLY CUT OVER STOPEND &SEALED

APPLY MS SEALANT TO SEALFC BOARD TO FASCIA BOARD

STOP SPOUTING & FASCIAMIN.10mm CLEAR OF FINISHEDWALL CLADDING

NOTE:FOR DURABILITY OF FLASHINGS - REFER TABLE 20NZBC E2/AS1 DOCUMENT

ROOF UNDERLAY OMITTED FOR CLARITY

SCALE 1:10

50x50mm COVER BACKFLASHING BEHIND FASCIA &CLADDING


STO/MONOTEK


GUTTER/WALL JUNCTION

FCS 606

2017

SCALE 1:2

SELECTED ALUMINIUMWINDOW/DOOR JOINERY

PROVIDE AIRSEAL ON PEFROD GAP 7.5-8mm APPROX.WALL UNDERLAY DRESSEDINTO OPENING


100mm MIN.TO FACE OF CLADDING

SELECTED FIBRE CEMENTSOFFIT LINING18x18mm TIMBER BEADBETWEEN CLADDING ANDSOFFIT, PAINTED

LINE OF CLADDING BEYOND -SHOWN DASHED

varies


STO/MONOTEK


SOFFIT AT WINDOW/DOOR HEAD

FCS 607

2017

SCALE 1:5

ROOFSTRUCTURE

7.5/9.0mm REBATED SHEET OVER20mm DRAINED CAVITY - FIX INACCORDANCE TO MANUF. DETAILS

7535

REFER E2/AS1 TABLE 7

5mm

GAP

MAX

.FO

R N

OTC

HED

TUR

N-D

OW

N


STO uPVC CLIP ON TRAY -REMOVE BACK TAB IF REQ.

uPVC CAVITY CLOSER

UNDERLAY OR FLASHING TAPELAPPED OVER APRON FLASHINGUPSTAND

PRE FINISHED METAL APRONFLASHINGPREFINISHED METAL ROOFINGOVER UNDERLAY

SELECTED ROOF WRAP

ROOF UNDERLAYCONTINUOUS TO TOP OFFLASHING

STOPEND TO RUN 10mmMIN.PAST CLADDING

NOTE:

STOPENDS REQUIRED AT ROOF to WALLJUNCTION TO DIVERT WATER FROM CAVITY


STO/MONOTEK


APRON (TRANSVERSE) FLASHING

FCS 700

2017

SCALE 1:5

7535

ROOF RAFTER


uPVC CAVITY CLOSER

7.5/9.0mm REBATED SHEET OVER 20mmDRAINED CAVITY - FIX IN ACCORDANCEWITH MANUF. DETAILSSTOARMAT RENDER SYSTEM

STO uPVC CLIP ON TRAY -REMOVE BACK TAB IF REQ.

UNDERLAY OR FLASHING TAPELAPPED OVER APRONFLASHING UPSTAND

APRON FLASHING WITH TAPEREDDIVERTER FLASHING TO DIRECT WATERINTO GUTTER. CLADDING TO BECAREFULLY CUT OVER STOPEND &SEALED

NOTE: PROVIDE DIVERTER FLASHING AT ROOF TOGUTTER JUNCTION TO DIVERT WATER INTO THEGUTTER - Refer Drawing FCS 606 (Monotek)


STO/MONOTEK


APRON (PARALLEL) FLASHING

FCS 701

2017

SCALE 1:5

20mm DRAINED CAVITY

5mm

GAP

MAX

.FO

R N

OTC

HED

TUR

N-D

OW

N

7.5/9.0mm REBATED SHEETS - FIXIN ACCORDANCE WITH MANUF.DETAILS

VENTED CAVITY CLOSURE -STO uPVC CLIP ON TRAY


PREFINISHED METALAPRON FLASHINGPREFINISHED METALROOFING OVER UNDERLAY

SELECTED ROOF UNDERLAY

ROOF UNDERLAYCONTINUOUS TO TOP OFFLASHING

NOTE: CONTRACTOR TO FIT STOPEND FLASHING & HEMMEDFLASHING FOR FASCIAS 50mm BEHIND CLADDING, 50mm BEHINDFASCIA. STO CONTRACTOR TO APPLY FINISHED SEALANT JOINTBETWEEN FASCIA & PLASTER. UNDERLAY or FLASHING TAPE OVERFLASHING UPSTAND.

PARAPETS - REFER 500 SERIES - PARAPET DETAILS

50mm MIN.FASCIA BACKFLASHING - SHOWN DASHED

STOPEND FLASHING

7535 REFER E2/AS1 TABLE 7

5mm

GAP

MAX

.FO

R N

OTC

HED

TUR

N-D

OW

N


STO/MONOTEK


INTERSTOREY TRANSVERSE (APRON) ROOF STOPEND

FCS 702

2017

SCALE 1:5

STOP END 10mm PASTFINISHED CLADDING

20mm DRAINEDCAVITY

MEMBRANE OVER COVERBOARD WITH DRIP EDGE

10

10



35

75

150

FASCIA 10mm SHORT OFFINISHED CLADDING WITH MSSEALANT JOINT

BACK FLASHING 50mm BEHINDFASCIA & CLADDING

STO STICK ON CONNECTOR or MSSEALANT JOINT ON PEF RODBETWEEN STOPEND AND CLADDING

ROOFING MEMBRANE OVER METALSTOPEND. STOPEND TO EXTEND 10mmMIN.PAST FINISHED WALL

ROOFING MEMBRANE 150mmMIN.UPSTAND, 75mm CLADDING COVER,

CLADDING 35mm MIN. ABOVE MEMBRANE

110

3476

150

10

BATTEN TO BLOCK CAVITY

IF MEMBRANE

IF ROOF

CLADDING

ROOF/DECK NOTE: MEMBRANE NOT SHOWN ON STOPEND FOR CLARITY

A = CAVITY & FINISHED CLADDING + 10mm

75mm MIN.A


STO/MONOTEK


INTER-STOREY FLAT (MEMBRANE)ROOF STOPEND

FCS 703

2017

SCALE 1:5

WALL UNDERLAY

TIMBER FRAMING TONZS 3604

20mm DRAINEDCAVITY

7.5/9.0mm REBATED SHEET -FIX IN ACCORDANCE WITHMANUF. DETAILSSTOARMAT RENDER SYSTEM

FASCIA 10mm SHORT OFCLADDING MS SEALANT JOINTFASCIA / CLADDING BACKFLASHING, MIN 50mm COVERH3.1 PRE PRIMED & PAINTEDFASCIA/BARGE BOARD -SHOWN DASHED

10

PRE FINISHED METAL FLASHINGOVER FASCIA

APRON FLASHINGSTOPEND


STO/MONOTEK


INTER-STOREY ROOF STOPEND - PLAN VIEW

FCS 704

2017

7550

DRESS WALLUNDERLAY OVER

GUTTER LINING

SELECTED GUTTER LINING CARRIEDOVER ANTI-PONDING BOARD AND UPABUTMENT FRAME ON NOG TO SUIT

GUTTER BOARD AT ABUTMENTON NOGS TO SUIT

ANTI-PONDING BOARDLAID TO A FALL

ROOF UNDERLAYCARRIED DOWNOVER GUTTER LINING

MASONRYROOFING TILE

SCALE 1:5

STO uPVCCLIP ON TRAY

100mm MIN.

20mm DRAINED CAVITY7.5/9.0mm REBATED SHEET -FIX IN ACCORDANCE TOMANUF. DETAILSSTOARMAT RENDER SYSTEM


STO/MONOTEK


ROOF PENETRATION/GUTTER (Masonry Tile) DETAIL

FCS 705

2017

SCALE 1:5

80mm MIN. 80mm MIN.

20m

m M

IN.

110m

m

NOTE: WHERE GUTTER FINISHES WITHIN THE LENGTH OF THE WALL, STEP LOWER PART OFGUTTER OUT TO 10mm PAST THE CLADDING LINE, WHILE MAINTAINING REQ.CLEARANCES, TOALLOW THE GUTTER TO FEED INTO THE LOWER EAVES GUTTER.- REFER Fig: 37 & Fig: 50 Incl.Section 8.1.6.2

35m

m G

AP

75m

m M

IN.C

OV

ER

MIN

.TO

TAL

WALL UNDERLAY OVERGUTTER UPSTANDPREFINISHED METAL GUTTER

STO uPVC VENTED CAVITYCLOSER & STO uPVC CLIP ONTRAY

20mm DRAINED CAVITY7.5/9.0mm REBATED SHEET -FIX IN ACCORDANCE WITHMANUF. DETAILSSTOARMAT RENDER SYSTEM


STO/MONOTEK


PARALLEL ROOF/HIDDEN GUTTER

FCS 706

2017

SCALE 1:5

WALL UNDERLAY20mm DRAINED CAVITY7.5/9.0mm REBATED SHEET -FIX IN ACCORDANCE WITHMANUF. DETAILSSTOARMAT RENDER SYSTEM

6mmMAX.GAP

50/90mm LAP REFER NZBC,TABLE 7 E2/AS1 FORFLASHING DIMENSIONS

H3.1 PRE PRIMED & PAINTEDFASCIA/BARGE BOARD

PRE FINISHED METALFLASHING

MS SEALANT ON PEF ROD FOREXPOSED SITES

ALLOW FOR STO uPVC CLIPON FLASHING

PRE FINISHED METAL ROOFINGOVER ROOF UNDERLAY

50 c

over


STO/MONOTEK


FACE FIXED FASCIA/BARGE

FCS 707

2017

SCALE 1:5

20mm DRAINED CAVITY


SELECTED MEMBRANE FINISHOVER H3 "C" FACED PLYWOOD LAIDTO 1:30 MIN.FALL. GLUE & SCREWTO TIMBER JOISTS, ALL EDGESSUPPORTED ON FRAMING

TAKE BOTH LAYERS 6mm PASTS/S ANGLE TO FORM DRIP EDGE

MIN.5mm RADIUSTO PLYWOOD

PREFINISHED METAL SPOUTINGAND BRACKETS

WALL UNDERLAY

50mm MIN. LAP REFER E2/AS1

H3.1 PRE PRIMED & PAINTEDFASCIA/BARGE BOARDMS SEALANT ON PEF ROD




STO/MONOTEK


FACE FIXED FASCIA/MEMBRANE ROOF

FCS 708

2017

SCALE 1:5

ROOFSTRUCTURE

PREFINISHED METALFLASHING, TURN DOWN TOSUIT PROFILEPREFINISHED METALROOFING OVER UNDERLAYSELECTED ROOF WRAP

50/90mm LAP REFER NZBC,TABLE 7 E2/AS1 FORFLASHING DIMENSIONSH3.1 PRE PRIMED & PAINTEDFASCIA/BARGE BOARD

PRE FINISHED METALFLASHING

MS SEALANT ON PEF ROD FOREXPOSED SITES



7.5/9.0mm MONOTEKSTOARMAT RENDER SYSTEM


STO/MONOTEK


ROOF/WALL RIDGE

FCS 709

2017

PENETRATION APRON FLASHINGHEM FOLD UNDER ROOFING

SEPARATE ROOFING SHEETOVER

MIN. UPSTAND 110mm

SIDE COVER= 2 CRESTS

STOARMAT RENDER SYSTEMWITH PREMESHED EXTERNALCORNERS

H3.1 TIMBER CAVITY BATTENSFIBRE CEMENT SHEETWALL CLADDING

35mm GAP BETWEENCLADDING AND FLASHING

SET ONE CORNER OF UPSTANDHIGHER UP ROOF PLANE

TO PROVIDE CROSS FALL

250mm MIN.

110

35

130 - 200

130 - 200

COVER 130 - 200mm MAX.REFER TO E2/AS3 Table 7

110

NOTE:SUITABLE FOR RECTANGULAR PENETRATIONS UP TO 1200mmWIDE.ROOF PITCH MUST BE 10° or HIGHER - REFER TO E2/AS1TABLE 9 or 17 FOR MAX.ROOF LENGTH ABOVE PENETRATIONS.BLOCKING REQUIRED FOR PENETRATIONS OVER 200mm

FRAMED CHIMNEYSCALE 1:20

UNDERLAY SEPARATOR BETWEENFLASHING AND FRAMING. FRAME TO

SUPPORT FLASHING

PREFINISHED METAL ROOFINGOVER UNDERLAY

SELECTED ROOF WRAPE2/AS3 COMPLIANT METAL APRONFLASHING

STO uPVC CLIP ON FOOTTRAY

SECTION/FRAMED CHIMNEYSCALE 1:10

7535

3575

110

110

STOARMAT RENDER SYSTEM OVER 7.5-9.0mmFIBRE CEMENT SHEET

20mm DRAINED CAVITYWALL UNDERLAY LAPS OVER

FLASHING


STO/MONOTEK


FRAMED CHIMNEY OR PENETRATION UP TO 1200mm

FCS 710

2017

SCALE 1:2

WALL UNDERLAYCONTINUOUS AROUNDCORNER

H3.1 SCRIBER TO SUITWEATHERBOARD PROFILE

SELECTED HORIZONTALTIMBER WEATHERBOARDSOVER 20mm DRAINEDCAVITY

50m

m M

IN.C

OV

ER

10mm MIN.GAP

50mm x 50mm BACKFLASHING

NOMINAL 20x45mm H3.1TIMBER CAVITY BATTEN7.5/9.0mm REBATEDSHEETSTOARMAT RENDER SYSTEMWITH STO uPVC CLIP ONTRAY

MIN.ex 25mm COVER BOARDWITH 6x6mmWEATHERGROOVES


STO/MONOTEK


WEATHERBOARD/FC SHEET EXT.CORNER - OPT 1

FCS 800

2017

SCALE 1:2

PURPOSE MADEFLASHING

5mm

50mm COVER

50m

m

NOTE: IF A TIMBER SCRIBER REQUIREDEXTEND FLASHING ACCORDINGLY

SELECTED HORIZONTALTIMBER WEATHERBOARDSOVER 20mm DRAINEDCAVITY

STO uPVC CLIP ON TRAY

MS SEALANT



7.5/9.0mm REBATEDFIBRE CEMENT SHEET


STO/MONOTEK


WEATHERBOARD/FC SHEET EXT.CORNER - OPT 2

FCS 801

2017

SCALE 1:2

E2/AS1 COMPLIANTFLASHING

5mm

50m

m

NOTE: IF A TIMBER SCRIBER REQUIREDEXTEND FLASHING ACCORDINGLY

BUILDING UNDERLAYCONTINUOUS AROUNDCORNER

STO uPVC CLIPON TRAY

MS SEALANT


7.5/9.0mm REBATEDFIBRE CEMENT SHEET

SELECTED HORIZONTALTIMBER WEATHERBOARDSDIRECT FIXED

50mmCOVER


STO/MONOTEK


W'BOARD/FC SHEET EXT.CORNER - DIRECT FIX

FCS 802

2017

SCALE 1:2

WALL UNDERLAY CONTINUOUSAROUND CORNER

50m

m M

IN.

50mm MIN.

COVER

CO

VE

R

NOMINAL 20X45mm H3.1TIMBER CAVITY BATTEN -FIX IN ACCORDANCEWITH MANUF.DETAILS

SELECTED HORIZONTAL TIMBERWEATHERBOARDS OVER 20mmDRAINED CAVITY

MS SEALANT ON PEF ROAD

E2/AS1 COMPLIANT FOLDEDMETAL FLASHING


STOARMAT RENDER SYSTEMWITH CLIP ON FLASHING


STO/MONOTEK


WEATHERBOARD/FC SHEET INT.CORNER - OPT 1

FCS 803

2017

SCALE 1:2



COVER

CO

VE

R

E2/AS1 COMPLIANT FOLDEDFLASHING

50mm MIN.

50m

m M

IN.

H3.1 SCRIBER TO SUITEWEATHERBOARD PROFILE

MS SEALANT ON PEF ROD

NOMINAL 20x45mm H3.1TIMBER CAVITY BATTEN -FIX IN ACCORDANCEWITH MANUF.DETAILS7.5/9.0mm REBATED SHEETSTOARMAT RENDER SYSTEMWITH STO uPVC CLIP ONFLASHING


STO/MONOTEK


WEATHERBOARD/FC SHEET INT.CORNER - OPT 2

FCS 804

2017

SCALE 1:2

WALL UNDERLAY CONTINUOUSAROUND CORNER

50m

m M

IN.

50mm MIN.

COVER

NOMINAL 20X45mm H3.1 TIMBER CAVITYBATTEN - FIX IN ACCORDANCE WITHMANUF.DETAILS

SELECTED HORIZONTAL TIMBERWEATHERBOARDS - DIRECT FIXED

MS SEALANT ON PEF ROAD

E2/AS1 COMPLIANT FOLDEDMETAL FLASHING


STOARMAT RENDER SYSTEMWITH CLIP ON FLASHING


STO/MONOTEK


W'BOARD/FC SHEET INT.CORNER - DIRECT FIX

FCS 805

2017

SCALE 1:2

50mm MIN. 50mm MIN.COVER

WALL UNDERLAY


E2/AS1 COMPLIANT TOP HATMETAL FLASHING

COVER


NOMINAL 20x45mm H3.1TIMBER CAVITY BATTENFIXED IN ACCORDANCE

WITH MANUF.DETAILS7.5/9.0mm REBATED SHEET

STOARMAT RENDERSYSTEM WITH STO

uPVC CLIP ON TRAY

40mm


STO VENTCLAD/MONOTEK


VERTICAL JOINT - WEATHERBOARD/FC SHEET

FCS 806

2017

MS SEALANT OR STO JOINTSEAL TAPE

SCALE 1:2


35m

m M

IN.

CO

VE

R35

mm

MIN

.C

OV

ER

BEVEL-BACK TIMBERWEATHERBOARDS TO NZS 3617OVER 20mm DRAINED CAVITY

FLASHING TAPE LAPPED OVERHEAD FLASHING

E2/AS1 COMPLIANT FLASHING

MIN. 10mm GAP

CAVITY CLOSER POSITIONEDTO GIVE 15mm MIN.DRIPEDGE TO CLADDING

STOARMAT RENDER SYSTEM WITHSTO uPVC MESHED FINISHINGEDGE


20mm DRAINED CAVITY

1. IN HIGH WIND ZONES INCREASEFLASHING COVER TO 60mm MIN.ANDUSE A RIGID UNDERLAY

10


STO/MONOTEK


HORIZONTAL JUNCTION W'BOARD/FC SHEET

FCS 807

2017

SCALE 1:2

35m

m M

IN.

CO

VE

R35

mm

MIN

.C

OV

ER

BEVEL-BACK TIMBERWEATHERBOARDS TO NZS 3617OVER 20mm DRAINED CAVITY

FLASHING TAPE LAPPED OVERHEAD FLASHING

CAVITY CLOSER POSITIONEDTO GIVE 15mm MIN.DRIPEDGE TO CLADDING

H3.1 SLOPED HORIZONTALPACKERS AS REQUIRED

RIGID AIR BARRIERTO GABLE END

H3.1 CONTINUOUS HORIZONTALTAPERED PACKER BEHINDCAVITY CLOSER TO RESTRICTAIRFLOW

ALU.INTER-STOREYFLASHING, STOPEND, 15°SLOPE & 35mm MIN.COVER

MS SEALANT TORENDER/FLASHING

7.5/9.0mm REBATED SHEETSTOARMAT RENDER SYSTEMWITH STO uPVC PRE MESHEDFINISHING EDGE

20mm DRAINED CAVITY

1. IN HIGH WIND ZONES INCREASEFLASHING COVER TO 60mm MIN.ANDUSE A RIGID UNDERLAY


STO/MONOTEK


GABLE END - WEATHERBOARD/FC SHEET

FCS 808

2017

SCALE 1:2

STO uPVC CLIP ON TRAYWITH MS SEALANT OVERPEF ROD

SELECTED BRICK VENEER40mm MIN.CAVITY


10

NOMINAL 20x45mm H3.1TIMBER CAVITY BATTENSINSTALLED INACCORDANCE WITHMANUF.DETAILSFLASHING TAPE AROUNDUNDERLAY 75mm MIN.



20mm DRAINED CAVITY

WALL UNDERLAY TO BECONTINUOUS AROUNDCORNER


STO/MONOTEK


BRICK VENEER/FC SHEET EXTERNAL CORNER

FCS 810

2017

SCALE 1:2

WALL UNDERLAY CONTINUOUSAROUND CORNERS


50m

m M

IN.

50m

m M

IN.

CO

VE

RC

OV

ER

MS SEALANTOVER PEF ROD

SELECTED BRICK VENEER 40mmMIN.CAVITY

E2/AS1 COMPLIANT FLASHING,HEM TO BOTH ENDS

7.5/9.0mm REBATED FIBRECEMENT SHEET OVER 20mmDRAINED CAVITY


STO uPVC CLIP ON TRAY -REMOVE DRIP EDGE


STO/MONOTEK


BRICK VENEER/FC SHEET INTERNAL CORNER OPT. 1

FCS 811

2017

SCALE 1:2

STO uPVC CLIP ON FLASHING MS SEALANT OVERSTO JOINT SEAL TAPE

SELECTED BRICK VENEER 40mmMIN.CAVITY



7.5/9.0mm REBATED FIBRECEMENT SHEETSTOARMAT RENDER SYSTEM

20mm DRAINED CAVITY

BACK FLASHING TO CORNER

50


STO/MONOTEK


BRICK VENEER/FC SHEET INTERNAL CORNER - OPT 2

FCS 812

2017

SCALE 1:2


STOARMAT MIRALRENDER SYSTEM ONSELECTEDCONCRETE BLOCK

STO PREMESHEDCORNER

STO uPVC CONTROLJOINT WITH MSSEALANT IN STOARMATMESHED PLASTER

DPC

10



20mm DRAINEDCAVITY


STO/MONOTEK


EXTERNAL CORNER CONC.BLOCK/FC SHEET

FCS 830

2017

SCALE 1:2

USE STO S - PROTECT COATING SYSTEM FOR CLEAR FINISHED CONCRETE BLOCK

DPC

STOARMAT MIRAL RENDERSYSTEM or S-PROTECT CLEARON SELECTED CONCRETEBLOCK

E2/AS1 COMPLIANT BACKFLASHING CHASED & SEALEDINTO CONC.BLOCK

MS SEALANTOVER PEF ROD

7.5/9.0mm REBATED SHEETSTOARMAT RENDER SYSTEMWITH STO uPVC CLIP ON orFINISHING EDGE

20mm DRAINED CAVITY


STO/MONOTEK


INTERNAL CORNER CONC.BLOCK/FC SHEET

FCS 831

2017

SCALE 1:2

STOARMAT MIRAL RENDERSYSTEM ON SELECTEDCONCRETE BLOCK SERIESSTO uPVC CONTROL JOINTALLOW 10mm GAP IN FCSHEET

10mm

DPC

7.5/9.0mmREBATED SHEET


20mm DRAINED CAVITY


STO/MONOTEK


VERTICAL JOINT CONC.BLOCK/FC SHEET

FCS 832

2017

11m

m M

IN.

SCALE 1:2

DPC

FORM RENDERED REBATE INCONC.BLOCK WITH 15° SLOPE

STOARMAT MIRAL RENDERSYSTEM TO SELECTEDCONC.BLOCK

STO FLEXYL MESHEDWATERPROOF UPTURN/DOWNTURN CONC.BLOCKREBATE SURFACES, RENDERTOP OF REBATE

6

5mm

GAP

15



20mm DRAINED CAVITY

uPVC VENTED BASE CAP

STO uPVC CLIPON FOOT TRAYREMOVE BACK TAB IFREQUIRED

50m

m m

in.


STO/MONOTEK


HORIZONTAL JUNCTION CONC.BLOCK/FC SHEET

FCS 833

2017

SCALE 1:2


WALL UNDERLAY CONTINUOUSAROUND CORNERS,POLYPROPYLENE FLASHING TAPEAPPLIED TO PROTECT WALLUNDERLAY 75mm MIN.WIDE

NOTE: FINISH STO CLADDING SYSTEM BEFOREINSTALLING STONE CLADDING

PROPRIETARY MANUF.STONECLADDING FIXED ACCORDINGTO MANUF.CONSTRUCTIONDETAILS

MS SEALANT ONPEF ROD

SEALANT TOJUNCTION

STO uPVC CLIPON FLASHING

7.5/9.0mm REBATED FCSHEET

20mm DRAINED CAVITY



STO/MONOTEK


EXT.CORNER - MANUF.STONE/FC SHEET

FCS 840

2017

SCALE 1:2


WALL UNDERLAYCONTINUOUS AROUNDCORNERS

STO PREMESHED PVCCNR.ANGLES ON ALLEXT.CNRS

E2/AS1 COMPLIANTBACK FLASHING

PROPRIETARY STONE VENEER CLADDINGFIXED ACCORDING TOMANUF.CONSTRUCTION DETAILS

2mm GAP BETWEENSHEETS7.5/9.0mm REBATED SHEET

20mm DRAINED CAVITY

STOARMAT RENDERSYSTEM WITH STO uPVC

CLIP ON TRAY or FINISHINGEDGE


STO/MONOTEK


BOXED EXT.CORNER - STONE VENEER/FC SHEET

FCS 841

2017

SCALE 1:2


DOUBLE STUD REQUIRED

E2/AS1 COMPLIANT 50x50mmCORNER FLASHING

8mm BETWEEN SHEETS, MSSEALANT JOINT

NOTE: INSTALL FC SHEET AND FINISH STOCLADDING SYSTEM BEFORE INSTALLING STONE

8

MS SEALANT ON PEF RODPROPRIETARY MANUF.STONE CLADDINGFIXED ACCORDING TOMANUF.CONSTRUCTION DETAILS

STO uPVC CLIP ON TRAY7.5/9.0mm REBATED FC SHEET


20mm DRAINED CAVITY



STO/MONOTEK


INTERNAL CORNER - MANUF.STONE/FC SHEET

FCS 842

2017

SCALE 1:2

50mm MIN. 50mm MIN.COVER COVER


E2/AS1 COMPLIANTBACK FLASHING

PROPRIETARY MANUF.STONE CLADDINGOVER FIXED ACCORDING TOMANUF.CONSTRUCTION DETAILS


STOARMAT RENDERSYSTEM WITH STO uPVC

CLIP ON TRAY

20mm DRAINED CAVITY


STO/MONOTEK


VERTICAL JUNCTION - MANUF.STONE/FC SHEET

FCS 843

2017

SCALE 1:2


MS SEALANT ON PEF RODor STO JOINT SEAL TAPE

SCHIST OR STONE VENEER CLADDINGFIXED ACCORDING TOMANUF.CONSTRUCTION DETAILS

INSTALL FC SHEET ANDFINISH STOARMATCLADDING SYSTEMBEFORE INSTALLINGSCHIST OR STONE

WALL UNDERLAYCONTINUOUS AROUNDCONERS,POLYPROPYLENE FLASHINGTAPE APPLIED TOPROTECT WALLUNDERLAY 75mmMIN.WIDE

STO uPVC CLIPON FLASHING

MS SEALANT/STOSEAL TAPE


20mm DRAINEDCAVITY7.5/9.0mm REBATEDFC SHEET


STO/MONOTEK


EXT.CORNER - SCHIST or STONE VENEER/FC SHEET

FCS 844

2017

SCALE 1:2


NOTE: INSTALL FC SHEET AND FINISH STOCLADDING SYSTEM BEFORE INSTALLING STONE

E2/AS1 COMPLIANT BACK FLASHINGWITH 50mm MIN. COVER TOCLADDING

8mm BETWEENSHEETS, MS SEALANT

DOUBLE STUD REQUIRED

50m

m M

IN.

8

MS SEALANT ON PEF ROD or STOJOINT SEAL TAPESCHIST OR STONE VENEER CLADDING ANFIXED ACCORDING TOMANUF.CONSTRUCTION DETAILS

7.5/9.0mm REBATED FC SHEET


20mm DRAINED CAVITY



STO/MONOTEK


INT.CORNER - SCHIST or STONE VENEER/FC SHEET

FCS 845

2017

SCALE 1:2


E2/AS1 COMPLIANT BACK FLASHINGWITH 50mm MIN.CLADDING COVER

SCHIST OR STONE VENEERCLADDING FIXED ACCORDING TOMANUF.CONSTRUCTION DETAILS

50mm COVER 50mm COVER


STOARMATRENDER SYSTEM

CAVITY BATTENS

STO uPVC CLIP ONFLASHING


STO/MONOTEK


VERTICAL JUNCTION - SCHIST or STONE VENEER/FC SHEET

FCS 846

2017

SCALE 1:2

NOTE:SCHIST OR STONE VENEERCLADDING FIXED ACCORDING TOMANUF.CONSTRUCTION DETAILS

TOP PIECE OF SCHIST OR STONEMUST EITHER BE PLACED OR CUT SOA 15° SLOPE IS FORMED ON THE SILL

10m

mG

AP

35m

mC

OV

ER

STO uPVC CLIP ON FLASHING

VERMIN TRAY - BY OTHERS

TAPE OVER FLASHING



20mm DRAINED CAVITY


STO/MONOTEK


HORIZ.JUNCTION - SCHIST or STONE VENEER/FC SHEET

FCS 847

2017

SCALE 1:2

5mm



INTERNAL LINING

ARCHITRAVE ORSLIMLINE DETAIL

TIMBER WINDOW HEAD -PROFILE TO NZS 3610


UNDERLAY AT CORNERS ASPER E2/AS1

ALUMINIUM HEADFLASHING MIN.0.55 BMT,STOP ENDED WITH 15°SLOPE AND 20mm COVER

FIBRE CEMENT SHEET TO OVERHANG VERMIN TRAY BY 15mm min. FIT CLIPON TRAY AND LEAVE 5mm min.CLEARANCE TO HEAD FLASHING.PROPRIETRY ALUM. HEAD FLASHING TO COVER WINDOW FACING BY 20mm SLOPED 15° WITH min. 35mmUPSTAND TAPED TO WALL UNDERLAYALLOW HEAD FLASHING TO PASS JAMBS BY 30mm BEND UP ENDS BY 20mm TO CREATE STOP ENDS IN CAVITYFLASHING TAPE SYSTEM TO BE INSTALLED AROUND JOINERY OPENINGS AS PER E2/AS1 BY BUILDER.

20

PROVIDE FIRM SUPPORT(TIMBER PACKER) TOFACING



20mm DRAINED & VENTEDCAVITY - BATTENS AT 450mmMAX.CTRS.

VENTED VERMIN TRAY min.15mm UPSTO uPVC CLIP-ON TRAYWITH MIN 5mm GAP

PROPRIETARY TAPE ORALTERNATIVELY ADDITIONALLAYER OF BUILDING WRAPOVER HEAD FLASHING


STO/MONOTEK


TIMBER WINDOW JOINERY - HEAD DETAIL

FCS 870

2017

SCALE 1:2

INTERNAL LINING

TIMBER TRIM

CONTINUOUS PACKING


MS SEALANT

WALL UNDERLAY TURNEDINTO FRAMING REVEALS

AND TAPED AT CORNERS

SILL FLASHING WITHSTOP-END, LAPPEDUNDER JAMB PACKER

TIMBER WINDOW SILLTO NZS 3610



UNDERLAY AT CORNERS

10

25



VERTICAL CAVITYBATTENS

EDGE OF SHEET TO BESEALED BEFOREWINDOW IS INSTALLED


STO/MONOTEK


TIMBER WINDOW JOINERY - SILL DETAIL

FCS 871

2017

SCALE 1:2

TIMBER JAMB -PROFILE TO NZS 3610

INTERNAL LINING

AIRSEAL GAP 7.5-8mmAPPROX

ARCHITRAVE ORSLIMLINE DETAIL

JAMB PACKER TOSUIT REBATE

LINE OF HEADFLASHING

LINE OF SILL FLASHING -LAPPED UNDER JAMBPACKING

WALL UNDERLAY TURNEDINTO FRAMING REVEALS

AND TAPED AT CORNERS


ALUM. JAMB BACK FLASHINGNOTCHED INTO TIMBERWINDOW SILL JOINERY WITHMS SEALANT TO FINISH

STO STICK ON JOINERYCONNECTOR AT SILL FORPLASTER



STO/MONOTEK


TIMBER WINDOW JOINERY - JAMB DETAIL

FCS 872

2017

SCALE 1:2

TIMBER PACKER TOSUPPORT FLOORING

E2/AS1 COMPLIANT SILLFLASHING STOP ENDEDAND LAPPED UNDER JAMBPACKERS

MS SEALANT

PROPRIETARY FLASHINGTAPE TO RUN 100mm UPJAMBS

TIMBER DOOR SILL TONZS 3610

50m

m M

IN.

15

WALL UNDERLAY TURNEDINTO FRAMING REVEALS ANDTAPED AT CORNERS

20mm DRAINED & VENTEDCAVITY - BATTENS AT450mm MAX CTRS.

BOUNDARY JOIST20mm CAVITY BATTENSFIXED IN ACCORDANCE

AS PER MANUF.DETAILS

AIR SEAL



7.5/9.0mm REBATED FC SHEET




STO/MONOTEK


TIMBER DOOR JOINERY - TIMBER FL.THRESHOLD

FCS 873

2017

SCALE 1:2

TIMBER SILL TONZS 3610

TIMBER SILL TRIM TOBLOCK CAVITY

UPSTAND TO SUITFLOOR FINISHES

NOTE: SILL TO BE SNUGFIT AS AIR SEAL

REBATE OR CUT SLAB -RENDER TO SUIT SILL

SLOPE & WATERPROOFWITH STO FLEXYL

PROPRIETARY FLASHINGTAPE 100mm UP JAMB AT

STUD AS PER E2/AS1 100m

m M

IN. U

P J

AM

B

DPC

STO uPVC CLIP ONFLASHING

NOTE:FOR CLEARANCE BETWEENCLADDING AND ADJACENT GROUND- REFER NZS3604



STO/MONOTEK


TIMBER DOOR JOINERY - CONC. FL.THRESHOLD

FCS 874

2017

SCALE 1:2

FLASHMAN EXTRUDED ALUMINIUMONE PIECE CAVITY CLOSURE ANDHEAD FLASHING WITH STOP END(SHOWN DASHED)

5

AIRSEAL OVER PEFROD GAP 7.5-8mm

APPROX


INTERIOR LINING


SEALANT REQUIRED TOCLOSE HEAD FLASHINGALUMINIUM WINDOWJOINERY

25

25mm MIN. FROM OUTSIDE OF FRAMINGTO BACK OF WINDOW FLANGE

PROPRIETARY TAPE OVER HEADFLASHING SUPPLIED ANDINSTALLED BY FLASHMANCONTRACTOR

WALL UNDERLAY INSTALLEDAS PER E2/AS1



20mm DRAINED CAVITY

STO uPVC CLIP-ON TRAY


STO/MONOTEK


FLASHMAN HEAD FLASHING

FCS 878

2017

SCALE 1:2

FLASHMAN ALUMINIUM MITRESOAKER SUPPLIED BY FLASHMAN

INSTALLED BY BUILDER

H3.1 PACKER SUPPLIED ANDINSTALLED BY FLASHMAN




UNDERLAY

AIRSEAL ON PEF RODGAP 7.5-8mm APPROX.

FLASHMAN BACK PLATE -SHOWN DASHED

FLASHMAN EXTRUDEDALU.SLIMLINE SILL

25mm MIN. FROM OUTSIDE FACEOF THE FRAMING LINE TO THEBACK OF WINDOW FLANGE

25

8

SUPPORT PACKER

14 GAUGE HOT DIPGALV.(316SS WHERE REQ.)S.T.H.C SCREWS @ 600mmCTRS. WITH 65mm MIN. FRAMEPENETRATION. SUPPLIED BYFLASHMAN



CAVITY BATTENS

STO uPVC STICK ONJOINERY CONNECTOR8mm MIN.STO uPVC CLIP ONFLASHING


STO/MONOTEK


FLASHMAN SILL FLASHING

FCS 879

2017

SCALE 1:2

CAVITY BATTENS

LINE OF FLASHMANSLIMLINE SILL

INTERNAL LINING


FLASHING TAPE(100mm UP JAMBS)



ALUMINIUMWINDOW JOINERY

25mm MIN. FROM OUTSIDEFACE OF FRAMING TOBACK OF WINDOW FLANGE

25




FLASHMAN EXTRUDEDALUM.JAMB FLASHING

H3.1 PACKER SUPPLIEDAND INSTALLED BYFLASHMAN CONTRACTOR

STO uPVC STICK ONJOINERY CONNECTOR


STO/MONOTEK


FLASHMAN JAMB FLASHING

FCS 880

2017

SCALE 1:2

AIRSEAL OVER PEFROD GAP 7.5-8mm

APPROX


INTERIOR LINING STO uPVC CLIP-ON FLASHING


SEALANT REQUIRED FORVERY HIGH AND EXTRAHIGH WIND ZONES

PROPRIETARY HOMERITPVC WINDOW JOINERY

PROPRIETARY ALUMINUMWINDOW HEAD FLASHING, 15°SLOPE AND 10mm COVER ATWINDOW HEAD

5


7.5/9.0mm REBATEDFC SHEET


20mm DRAINED CAVITY

FLASHING TAPE ONTO WALLUNDERLAYuPVC VENT STRIP

1. IN EXTRA HIGH WIND ZONESINCREASE FLASHING COVER TO60mm AND USE A RIGID UNDERLAY


STO/MONOTEK


HOMERIT PVC JOINERY - HEAD DETAIL

FCS 881

2017

SCALE 1:2




UNDERLAY AS PER E2/AS1


INTERIOR LINING

JOINERY SUPPORT BARREQUIRE FOROPENINGS OVER 600mm

PROPRIETARY HOMERITPVC WINDOW JOINERY

MS SEALANT

STO uPVC SILL FLASHING



CAVITY BATTENS


STO/MONOTEK


HOMERIT PVC JOINERY - SILL DETAIL

FCS 882

2017

SCALE 1:2

INTERNAL LINING


FLASHING TAPE ASPER E2/AS1



PROPRIETARYHOMERIT PVCWINDOW JOINERY

MS SEALANT

LINE OF SILLFLASHING

LINE OF HEADFLASHING


WALL UNDERLAY LAPPED & STAPLEDONTO INSIDE FRAME COVERED WITH

FLASHING TAPE AS PER E2/AS17.5/9.0mm

REBATED SHEETCAVITY BATTENS

STO uPVC JAMB FLASHING GLUEOR BED FLASHING IN PLACE

BEFORE RENDERING


STO/MONOTEK


HOMERIT PVC JOINERY - JAMB DETAIL

FCS 883

2017

stoarmat render system drawing register 2017 render system on... · stoarmat render system timber...

Documents