sunanda - sunandaglobal.com sunanda speciality coatings pvt. ltd. sunanda speciality coatings pvt....

SUNANDA SPECIALITY COATINGS PVT.LTD.

BILL OF QUANTITIES

INDIA U.S.A. U.A.E. TANZANIA GHANA KENYA

ETHIOPIA MALDIVES NEPAL AFGHANISTAN RUSSIA OMAN

CONCRETE MATERIALS CONSULTANCY DIVISION Satyadham, Road No. 2, Sion (E),

Mumbai – 400 022, India Tel: +91-22-24034130 / Fax: +91-22-24034133

Email : [email protected] Website : www.sunandaglobal.com

Consultants for Building Materials Manufacturers of Construction Chemicals since 1979

ISO 9001:2008

mailto:[email protected]

http://www.sunandaglobal.com/

http://www.sunandaglobal.com/

2

Sunanda Speciality Coatings Pvt. Ltd. www.sunandaglobal.com

SUNANDA S P E C I A L I T Y C O A T I N G S P V T . L T D

A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

I N D E X

Sr. No. PARTICULARS Pg No

A. SPECIALISED ADMIXTURES FOR PCC & RCC WORKS

1. Integral Waterproofing Admixture for PCC Works 4

2. Superplasticisers for RCC Members 4

3. Integral Corrosion Inhibiting Admixture for RCC Members 5

4. Protection to Foundation from Chloride Attack. 5

Option 1 - Tar Modified Epoxy Coating For Foundation Protection

Option 2 – Polymer Modified Bitumous Coating For Foundation Protection

5. Repairs of Honeycombed Concrete 6

B. EXTERNAL APPLICATIONS

6. External Crackless Plaster 7

7. Waterproofing of Dead Walls 7

8. 100% Acrylic, Decorative, Waterproof And Heat Insulating Paint For External Walls

8

9. Textured Paint/ Finish 9

10. Treatment to Tie- Rod Hole On Mivan Shuttering Walls 9

C. WATERPROOFING TREATMENT TO VARIOUS AREAS

11. Podium Waterproofing

Waterproofing Treatment to Softscape Area 10-11

Waterproofing & Anti-Rooting Treatment To Planter Boxes 11

Waterproofing Treatment to Hardscape Area 11-12-13

12. Waterproofing Treatment of Water bodies 13-14

13. Waterproofing Treatment to R.C.C. Terrace Slab 14-15

14. Waterproofing Treatment to Toilet Blocks 16-17

15. Waterproofing Treatment to O.H.W.T. 17-18

16. Waterproofing Treatment to RCC Bore Packing 19

SUNANDA’S PRESENCE

3



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

D. DIFFERENT TYPES OF BONDING AGENT

17. Bonding Agent for C.M. Plaster with RCC Surface 20

18. Bonding Agent for RCC Construction Joints 20

19. Bonding Agent for Gypsum Plaster 20

20. Bonding Agent for Tile Fixing. 21

E. VARIOUS COATINGS & APPLICATION FOR CAR PARKING AREAS

21. Anti-Carbonation Coating 22

22. Epoxy Coating 22

23. Non-Metallic Floor Hardeners 23

Option1 : Dust Proof Liquid Floor Hardener

Option2: Dry Shake Floor Hardener

24. Hygienic Coating for Water Tanks 23

F. ANTI-CORROSIVE TREATMENT TO STEEL

25. Rust Removal and Conversion for Steel 24

26. Rust Passivation of Steel 24

27. Corrosion Protection to Steel With Sacrificial Anode -SUNANODE 24

28. Integral Corrosion Inhibiting Admixture 25

29. PU Coating For Protection to Structural Steel/ Railings/ Grills 25

G. ANCHORING OF DOWEL BARS

30. Anchoring Dowel Bars in RCC Members Using Epoxy Grouts 26

31. Rock Anchoring for Foundations/Rafts Using Microconcrete 26

H. CURING COMPOUNDS

32. Curing Compounds 27

I. EPOXY FLOORING

33a 1mm Self Levelling Epoxy flooring 28

33b 2mm Self Levelling Epoxy flooring 28

33c 3mm Epoxy Screed + Self Levelling Epoxy flooring 28

4



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

Sr. No Description of Works Qty Per Rate Rs.

Amount Rs.

A. SPECIALISED ADMIXTURES FOR PCC & RCC WORKS

1. INTEGRAL WATERPROOFING ADMIXTURE FOR PCC WORKS

A Providing and laying P.C.C. in designed grade at all heights and levels on well compacted/sound surfaces using a mechanical mixer including dewatering, shuttering, vibrating, curing and finishing as required. Admix POLYTANCRETE IWL of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent. It is to be added directly to the gauging water @200 ml per bag of cement. The rate to include for storage, handling, transportation of all materials, equipments, providing material test reports of Cement/Sand/Aggregates/Water from manufacturer and approved testing agencies, casting- curing and testing of concrete cubes @ three cubes/100 cum of concrete pour, etc. all complete to the satisfaction of the EIC

Cu. m

2. SUPERPLASTICISERS FOR RCC MEMBERS

A Providing and laying R.C.C. of designed grade at all heights and levels on well compacted/sound surfaces using a mechanical mixer including dewatering, shuttering, vibrating, curing and finishing as required. Admix superplasticiser POLYTANCRETE SPR of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent @ 150ml-200 ml per bag of cement The rate to include for storage, handling, transportation of materials, equipments etc using appropriate methods etc. complete.

a) For Footings and other foundation works Cu.m

b) For Columns at all levels

Cu.m

c) For Beams at all levels.

Cu.m

d) For Slabs at all levels Cu.m

5



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

3. INTEGRAL CORROSION INHIBITING ADMIXTURE FOR RCC MEMBERS

Providing and laying R.C.C. of designed grade at all heights and levels on well compacted/sound surfaces using a mechanical mixer including dewatering, shuttering, vibrating, curing and finishing as required. Admix integral corrosion inhibitor POLYALK CP293 of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent @ 0.5 to 1% by weight of cement depending on amount of chloride present. The rate to include for storage, handling, transportation of materials, equipments etc using appropriate methods etc. complete.

Cu.m

4. PROTECTION TO FOUNDATION FROM CHLORIDE ATTACK.

Option 1 - Tar modified epoxy coating for foundation protection

A Providing and applying two coats of protective membrane over the cured concrete surface like RCC footings, columns, plinth beams etc. which will be submerged under soil so as to protect the same. Apply two pack coal tar epoxy system of SUNEPOXY COAL TAR of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent.Mix Part A and Part B of SUNEPOXY COAL TAR in 1:1 ratio with slow speed stirrer and apply the same on a clean RCC surface by brush. Allow to set for 8-10 hours and apply the second coat. The rate to include for application at all levels to various RCC elements to the satisfaction of the EIC etc. complete.

Sq. m

Option 2 – Polymer modified bituminous coating for foundation protection

B Providing and applying coats of polymerized bituminous coating of POLYALK WPB over the cured concrete surface like RCC footings, columns, plinth beams etc. which will be submerged under soil so as to protect the same. Apply a primer coat of POLYALK WPB with equal amount of water. Prime surface should be allowed to dry for 24 hrs. Apply a coat of POLYALK WPB in a continuous unbroken film. Allow to set for 24 hours and apply the second coat. Avoid pinholes The rate to include for application at all levels to various RCC elements to the satisfaction of the EIC etc. complete.

Sq.m

6



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

5. REPAIRS TO HONEYCOMBED SURFACE

Clean & chip off the damaged and honeycombed RCC portion etc. Moisten the surface and apply bonding coat of POLYALK EP of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent to the entire honeycombed concrete surface. Hand pack Polymer Modified Mortar by mixing

1 part by weight of “POLYALK EP” 5 parts by weight of cement 15 parts by weight of well graded sand and water to achieve the desired consistency

At a time apply mortar layer not more than 15-20 mm thick. The mortar should be prepared using mechanical mixers / stirrers & should be well compacted and finished using appropriate methods. If the thickness of mortar required to make up the concrete section is more; then repeat above procedure. The rate to include for necessary compaction with mechanical plate vibrator etc. complete to the satisfaction of the EIC. Payment will be made on the quantity of “POLYALK EP” consumed.

Litrs

7



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

B. EXTERNAL APPLICATIONS

6. EXTERNAL CRACKLESS PLASTER

Providing and applying 20-25 mm thick sand faced cement plaster to external surfaces in two coats with first coat in 12-15 mm thick in 1:4 C.M and second coat in 8-10 mm thick in C.M 1:4 finished in proper line and level. Add in both the coats shrinkage compensating admixture cum plasticizer-“SUNPLEX” 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent per 50 Kg bag of cement. Add SUNPLEX in dry machine mix before addition of gauging water. The rate to include for drip moulds, grooves, bands, watas at all heights including necessary curing etc. complete.

Sq.m

7. WATERPROOFING OF DEAD WALLS

Clean the receiving plastered surface of all loose particles, dirt & rub down to original hard surface. Inspect for cracks if any, and clean and moisten them. Define the crack with sharp edge tool. Providing and applying ready to use acrylic polymeric non-shrink auto-suction putty – “POLYFILL-AR” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent on the crack and finish at all heights, level etc. complete. After 24 hours inspect and if required as a result of auto-suction, provide another filling over the same. Provide and apply 2 coats of POLYALK WP & cement in 1:1 proportion by weight in slurry form on the entire dead walls of the building. Prepare a slurry using 1 part by weight of POLYALK WP and 1 part by weight of fresh cement (white) (Do not add any water). Mixing is best done using a low-speed stirrer. Keep the mix continuously stirred so as to ensure brushable consistency. Air cure for 24 hrs for initial setting and then by sprinkling water for 3 days. The rate includes erection of scaffolding at all levels, applying coating, curing etc. all complete as per the satisfaction of the EIC.

Sq.m

8



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

8 100% ACRYLIC, DECORATIVE , WATERPROOFING & HEAT INSULATING EXTERNAL PAINT

A

Clean the receiving plastered surface of all loose particles, dirt & rub down to original hard surface. Inspect for cracks if any, and clean and moisten them. Define the crack with sharp edge tool. Providing and applying ready to use acrylic polymeric non-shrink auto-suction putty – “POLYFILL-AR” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent on the crack and finish at all heights, level etc. complete. After 24 hours inspect and if required as a result of auto-suction, provide another filling over the same. Provide and apply a coat of POLYALK WP & cement in 1:1 proportion by weight in slurry form on the crackfilled area

B

Providing and applying 100% acrylic, heat insulating and decorative external acrylic coating “SUNEXT-8” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent or equivalent or equivalent of approved shade. Mix 1 litre of “SUNEXT-8” with 1 L of water and use as priming coat on the surface. Mix 1 L of Sunext-8 with 400-500 ml of water, stir well and apply by brush for subsequent two coats. The process includes erection of scaffolding at all levels, applying three coats at an interval of 4-6 hours between each coat. Cure as normal etc. all complete as per the satisfaction of the EIC

Sq.m

9



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

9. TEXTURED PAINT/ FINISH

Clean the existing surface by scrubbing so as to remove all the dust, dirt, grime, oil etc and washing the surface clean with jet of water etc. complete to the satisfaction of the EIC. Apply textured coat- “POLYTEXT FINISH” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent using flat trowel at a thickness of 1.5-2 mm and repeat trowel on the spread material in one direction only till desired finish is obtained. Remove the excess POLYTEXT FINISH before material has set. Cure applied material for 12 - 16 hours prior to application of exterior paint. The rate includes erection of scaffolding at all levels, applying texture finish, curing etc. all complete as per the satisfaction of the EIC.

Sq. m

10. TREATMENT TO TIE- ROD HOLE ON MIVAN SHUTTERING WALLS

Clean the tie rod hole on the RCC surfaces and remove dust, loose particles, etc. Apply bonding coat slurry of POLYALK EP of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent to the entire surface. Provide Hand pack Polymer Modified Mortar within 10 to 15 minutes i.e. (wet on wet) as per following specifications using :

2 part by weight of “POLYALK EP” 5 parts by weight of cement 15 parts by weight of well graded sand

The mortar should be prepared using mechanical mixers/stirrers and should be well compacted and finished using appropriate methods. The rate to include for erecting necessary scaffolding, curing etc complete to the satisfaction of the EIC.

Nos

10



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

C. WATERPROOFING TREATEMENT TO VARIOUS AREAS

11 PODIUM WATERPROOFING A WATERPROOFING TREATMENT TO SOFTSCAPE AREA

1 Clean the existing surface for waterproofing treatment of Podium slab by removing dust, dirt, loose particles, cement laitance etc. using Floor Polishing Machine. Drilling holes at construction joints and identify damaged/honeycombed of the concrete surface and fixing PVC nozzles at 2-3 ft c/c and sealing the same with PMM, then total area to be filled with water minimum 6” deep for minimum 3 days, after 3 days of ponding slab shall be checked for leakage/ seepage even dampness and such area shall be marked and pressure grouting / crack filling shall be done, Identifying the cracks, construction joints & filling the same with Polymer Modified Mortar using POLYALK EP. Injection grouting shall be done with providing and injection non shrink cementations grout by mixing – 2 pouches (330 gms. Each) of “SUNPLEX” of M/s. Sunanda Speciality Coatings Pvt.Ltd. or equivalent and 50 kgs of cement and sufficient water for flow ability, Grouting the same under pressure in pre-drilled holes by grouting pump etc. complete. After grouting is completed after 24 hours, cut the nipples and seal it with PMM etc. complete. After completion of crackfilling & grouting again ponding shall be done for 3 days to ensure the success of pressure grouting, if there is no leakages/ seepage/ dampness then only further activities shall be started. Providing and applying three coats of POLYALK WP of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent by mixing it in cement in 1:1.25 ratio by weight at an interval of 24 hours. Using mechanical stirrer for mixing. Finally, providing and applying single coat of bonding agent HACK-AID-PLAST of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and providing wet on wet a cement mortar screed of 1:4 cement mortar in 12-15 mm thickness. Air cure the same for 24 hrs and thoroughly curing by filling water for 7 days, by making 6” vattas.

11



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

2

Providing and laying thick soaked brick bat coba in CS Mortar 1:3 to proper level and slope, curing shall be done with filling of water for 48 hrs fill up the BBK joints and lay metal coba in CM 1:3 by adding “SUNPLEX” and making 6” vattas on the junctions of wall and floor keeping surface rough for further tiling. Curing to be done for minimum 7 days. by filling water with vataas, then final inspection shall be carried out to ensure that there are no damp patches, leakages, seepages etc at lower slab., if any type of leakages, seepages damp patches are found, in that case same shall be repaired / part shall be redone as per requirement. Rate to include for making side watta in PMM, ponding for seven days by closing the outlets etc. complete to the satisfaction of the EIC. Further finishing as per requirement.

3

Sealing the cutouts in the slab and the pipes passing through the terrace floor by filling PMM/Micro-concrete.

Nos

B. WATERPROOFING & ANTI-ROOTING TREATMENT TO PLANTER BOXES

After above waterproofing application gets over as above for planter boxes. Smoothening and proper curing of IPS is done, mix 30% anti-rooting solution of SUN-ANTIFUNGAL of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent in water homogenously. Provide and apply first coat of anti-rooting coating of SUN- ANTIFUNGAL mixed with water by brush on the cured dash coat. Apply a second coat & third coat of SUN-ANTIFUNGAL over the first coat by maintaining 3-4 hours time interval. Proceed with earth filling etc.

Sq. m

C. WATERPROOFING TREATMENT TO HARDSCAPE AREA

1 Clean the existing surface for waterproofing treatment of Podium slab by removing dust, dirt, loose particles, cement laitance etc. using Floor Polishing Machine. Drilling holes at construction joints and identify damaged/honeycombed of the concrete surface and fixing PVC nozzles at 2-3 ft c/c and sealing the same with

12



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

PMM, then total area to be filled with water minimum 6” deep for minimum 3 days, after 3 days of ponding slab shall be checked for leakage/ seepage even dampness and such area shall be marked and pressure grouting / crack filling shall be done, Identifying the cracks, construction joints & filling the same with Polymer Modified Mortar using POLYALK EP. Injection grouting shall be done with providing and injection non shrink cementations grout by mixing – 2 pouches (330 gms. Each) of “SUNPLEX” of M/s. Sunanda Speciality Coatings Pvt.Ltd. or equivalent and 50 kgs of cement and sufficient water for flow ability, Grouting the same under pressure in pre-drilled holes by grouting pump etc. complete. After grouting is completed after 24 hours, cut the nipples and seal it with PMM etc. complete. After completion of crackfilling & grouting again ponding shall be done for 3 days to ensure the success of pressure grouting, if there is no leakages/ seepage/ dampness then only further activities shall be started. Providing and applying two coats of POLYALK WP of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent by mixing it in cement in 1:1.25 ratio by weight at an interval of 24 hours. Using mechanical stirrer for mixing. Finally, providing and applying single coat of bonding agent HACK-AID-PLAST of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and providing wet on wet a cement mortar screed of 1:4 cement mortar in 12-15 mm thickness. Air cure the same for 24 hrs and thoroughly curing by filling water for 7 days, by making 6” vattas of the EIC. Further finishing as per requirement.

Sq. m

2

Providing and laying 4½” thick soaked brick bat coba in CS Mortar 1:3 to proper level and slope, curing shall be done with filling of water for 48 hrs fill up the BBK joints and lay metal coba in CM 1:3 by adding “SUNPLEX” and making 6” vattas on the junctions of wall and floor keeping surface rough for further tiling. Curing to be done for minimum 7 days. by filling water with vataas, then final inspection shall be carried out to ensure that there are no damp patches, leakages, seepages etc at lower slab., if any type of leakages, seepages damp

13



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

patches are found, in that case same shall be repaired / part shall be redone as per requirement. Rate to include for making side watta in PMM, ponding for seven days by closing the outlets etc. complete to the satisfaction of the EIC. Further finishing as per requirement.

3 Sealing the cutouts in the slab and the pipes passing through the terrace floor by filling PMM/Micro-concrete.

Nos

12. WATERPROOFING TREATMENT TO WATERBODIES

1. Clean the RCC side walls and base slab surface for treatment by removing dust, dirt and layers of concrete over the surface. etc. using Floor Polishing Machine. Drilling holes at construction joints and identify damaged/honeycombed of the concrete surface and fixing PVC nozzles at 2-3 ft c/c and sealing the same with PMM, then total area to be filled with water minimum 6” deep for minimum 3 days, after 3 days of ponding slab shall be checked for leakage/ seepage even dampness and such area shall be marked and pressure grouting / crack filling shall be done, Identifying the cracks, construction joints & filling the same with Polymer Modified Mortar using POLYALK EP. Injection grouting shall be done with providing and injection non shrink cementations grout by mixing – 2 pouches (330 gms. Each) of “SUNPLEX” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and 50 kgs of cement and sufficient water for flow ability, Grouting the same under pressure in pre-drilled holes by grouting pump etc. complete. After grouting is completed after 24 hours, cut the nipples and seal it with PMM etc. complete. After completion of crackfilling & grouting again ponding shall be done for 3 days to ensure the success of pressure grouting, if there is no leakages/ seepage/ dampness then only further activities shall be started. Providing and applying three coats of “POLYALK WP” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and cement in 1:1.25 ratio at an interval of 24 hours on the slab and side walls. Apply two coats and sure the same and apply the third coat and while it is still wet and tacky providing wet chat/dash coat of 1:4 cement mortar in 10-12 mm thickness.

Sq. m

14



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

2. Lay on the slab an average 2½” thick well soaked brick bat metal coba in cement mortar 1:4 to proper level and slope as per instructions adding “SUNPLEX” - 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent or equivalent or equivalent per 50 Kg bag of cement to the mortar mix. Fill up the brick joints and lay metal coba in C:M 1:4 adding “SUNPLEX”- 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent per 50 Kg bag of cement and finished with further provision of floor tiles. Rate to include for making side watta in PMM, ponding for seven days by closing the outlets etc. complete to the satisfaction of the EIC. Further finishing as per requirement.

Sq. m

13. WATERPROOFING TREATMENT TO R.C.C. TERRACE SLAB

A

Clean the RCC terrace slab surface for treatment by removing dust, dirt and layers of concrete over the surface. etc. using Floor Polishing Machine. Drilling holes at construction joints and identify damaged/honeycombed of the concrete surface and fixing PVC nozzles at 2-3 ft c/c and sealing the same with PMM, then total area to be filled with water minimum 6” deep for minimum 3 days, after 3 days of ponding slab shall be checked for leakage/ seepage even dampness and such area shall be marked and pressure grouting / crack filling shall be done, Identifying the cracks, construction joints & filling the same with Polymer Modified Mortar using POLYALK EP. Injection grouting shall be done with providing and injection non shrink cementations grout by mixing – 2 pouches (330 gms. Each) of “SUNPLEX” of M/s. Sunanda Speciality Coatings Pvt.Ltd. or equivalent and 50 kgs of cement and sufficient water for flow ability, Grouting the same under pressure in pre-drilled holes by grouting pump etc. complete. After grouting is completed after 24 hours, cut the nipples and seal it with PMM etc. complete. After completion of crackfilling & grouting again ponding shall be done for 3 days to ensure the success of pressure grouting, if there is no leakages/ seepage/ dampness then only further activities shall be

15



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

started. Providing and applying two coats of “POLYALK WP” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and cement in 1:1.25 ratio at an interval of 24 hours on the chajjas and extending it upto 1’0” over the side walls. Air cure the same for 24 hours and damp cure for next 4-5 days. Providing and applying single coat of bonding agent HACK-AID-PLAST of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent on the POLYALK WP coating by spray and providing wet on wet a chat/dash coat of 1:4 cement mortar in 10-12 mm thickness. All mortar mix to be necessarily added with “SUNPLEX” 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent or equivalent or equivalent per 50 Kg bag of cement. All coats of POLYALK WP to be inspected using a Magnifying glass by the EIC to satisfaction to ensure pinhole free coating. Ensure mechanical mixing of “POLYALK WP” and cement slurry using stirrers and check that cement particles do not settle down in the prepared mix. Consume the prepared mix within 30 minutes. Payment will be made as per the plan area.

Sq.m

B Lay small sized well soaked brick bat metal coba in cement mortar 1:3 to proper level and slope as per instructions adding “SUNPLEX” - 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent or equivalent or equivalent per 50 Kg bag of cement to the mortar mix. Fill up the joints and lay I.P.S adding SUNPLEX- 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent per 50 Kg bag of cement to the cement mortar 1:3 mixed and finished smooth with neat cement on top so as to drain water smoothly. Make chequered markings with a grid of 24”X 24”. Provide about 9” to 12” watta along the walls with cement mortar 1:3 small brick bats and IPS finish on the top. Rate to include for making border at the junction of watta and wall plaster, ponding for seven days by closing the RW outlets and making watas etc. complete to the satisfaction of the EIC.

Sq.m

16



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

C.

Providing and applying china mosaic chips over the surface of approved make and selected design over the I.P.S surface, vatas etc in cement mortar bedding including cleaning, acid washing etc. complete to the satisfaction of the EIC. Add “SUNPLEX”- 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent per 50 Kg bag of cement to the cement mortar bedding.

Sq.m

14. WATERPROOFING TREATMENT TO TOILET BLOCKS

A Clean the RCC slab surface & wall for treatment by removing dust, dirt and layers of concrete over the surface. etc. by mechanical means. Drilling holes at construction joints and identify damaged/honeycombed of the concrete surface and fixing PVC nozzles at 2-3 ft c/c and sealing the same with PMM, then total area to be filled with water minimum 6” deep for minimum 3 days, after 3 days of ponding slab shall be checked for leakage/ seepage even dampness and such area shall be marked and pressure grouting / crack filling shall be done, Identifying the cracks, construction joints & filling the same with Polymer Modified Mortar using POLYALK EP. Injection grouting shall be done with providing and injection non shrink cementations grout by mixing – 2 pouches (330 gms. Each) of “SUNPLEX” of M/s. Sunanda Speciality Coatings Pvt.Ltd. or equivalent and 50 kgs of cement and sufficient water for flow ability, Grouting the same under pressure in pre-drilled holes by grouting pump etc. complete. After grouting is completed after 24 hours, cut the nipples and seal it with PMM etc. complete. After completion of crackfilling & grouting again ponding shall be done for 3 days to ensure the success of pressure grouting, if there is no leakages/ seepage/ dampness then only further activities shall be started. Providing and applying two coats of “POLYALK WP” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and cement in 1:1.25 ratio at an interval of 24 hours on the terrace slab and extending it upto 1’0” over the F.F.L. Air cure the same for 24 hours and damp cure for next 4-5 days. Providing and applying single coat of bonding agent

17



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

“HACK-AID-PLAST” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent on the POLYALK WP coating by spray and providing wet on wet a chat/dash coat of 1:4 cement mortar in 10-12 mm thickness. All mortar mix to be necessarily added with “SUNPLEX” 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent per 50 Kg bag of cement. All coats of “POLYALK WP” to be inspected using a Magnifying glass by the EIC to satisfaction to ensure pinhole free coating. Ensure mechanical mixing of “POLYALK WP” and cement slurry using stirrers and check that cement particles do not settle down in the prepared mix. Consume the prepared mix within 30 minutes. Payment will be made as per the plan area.

Sq.m

B

Lay an average 2½” thick well soaked brick bat metal coba in cement mortar 1:4 to proper level and slope as per instructions adding “SUNPLEX” - 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent or equivalent per 50 Kg bag of cement to the mortar mix. Fill up the brick joints and lay metal coba in C:M 1:4 adding “SUNPLEX”- 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent or equivalent per 50 Kg bag of cement and finished with chequered markings for further provision of floor tiles. Rate to include for making border at the junction of watta and wall plaster, ponding for seven days by closing the SWR and soil outlets and making watas etc. complete to the satisfaction of the EIC.

Sq.m

15. WATERPROOFING TREATMENT TO O.H.W.T.

1. Clean the RCC slab surface & wall for treatment by removing dust, dirt and layers of concrete over the surface. etc. by mechanical means. Ensure that all bolt holes and sleeving of pipe inserts have been completed properly. Drilling holes at construction joints and identify damaged/honeycombed of the concrete surface and fixing PVC nozzles at 2-3 ft c/c and sealing the same with PMM, then total area to be filled with water minimum 6” deep for minimum 3 days, after 3 days of ponding slab shall be checked for leakage/ seepage even dampness and such area shall be marked and pressure

18



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

grouting / crack filling shall be done, Identifying the cracks, construction joints & filling the same with Polymer Modified Mortar using POLYALK EP. Injection grouting shall be done with providing and injection non shrink cementations grout by mixing – 2 pouches (330 gms. each) of “SUNPLEX” of M/s. Sunanda Speciality Coatings Pvt.Ltd. or equivalent and 50 kgs of cement and sufficient water for flow ability, grouting the same under pressure in pre-drilled holes by grouting pump etc. complete. 24 hours after grouting is completed, cut the nipples and seal it with PMM etc. complete. After completion of crackfilling & grouting again ponding shall be done for 3 days to ensure the success of pressure grouting, if there is no leakages/ seepage/ dampness then only further activities shall be started. Providing and applying three coats of “POLYALK WP” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and cement in 1:1.25 ratio at an interval of 24 hours on the slab and side walls. Apply two coats and cure the same and apply the third coat and while it is still wet and tacky providing wet chat/dash coat of 1:4 cement mortar in 10-12 mm thickness.

Sq.m

2. Lay Metal Coba in cement mortar in ratio1:3 by adding SUNPLEX on the base floor with vata at wall & floor junctions. On the side walls and ceiling provide double coat CS 1:3 Plaster with appropriate chemicals agents followed by curing for 7 days. All mortar mix to be necessarily added with “SUNPLEX” 330 gms pouch of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent or equivalent per 50 Kg bag of cement. All coats of “POLYALK WP” to be inspected using a Magnifying glass by the EIC to satisfaction to ensure pinhole free coating. Ensure mechanical mixing of “POLYALK WP” and cement slurry using stirrers and check that cement particles do not settle down in the prepared mix. Consume the prepared mix within 30 minutes. Payment will be made as per the plan area.

Sq.m

19



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

16 WATERPOOFING TREATMENT TO RCC BORE PACKING

Clean the Annular space around the pipe thoroughly; make the concrete surface rough so as to create bonding key for the micro-concrete to be placed. Similarly roughen the surface of PVC pipe (the part which is going into bore) using a rough file, wound 20 gauge GI wire around the pipe, Apply a bonding coat of SUNEPOXY-368 (Resin 1 kg and Hardener 0.3 gms) & after 20-30 minutes sprinkle sand layer on this portion to make surface rough Apply one coat of POLYALK EP the concrete and pipe surface & fill the annular space with micro-concrete POLYCRETE A with proper consistency and compact the same using proper tool, leaving. After 24 hours fix the PVC nozzles in the groove left and grout the same with cement using non shrink cement grout prepared by mixing cement (50Kgs) and SUNPLEX (330 gms pouch) as per standard specifications. Cut the nozzles after grouting. Pond the water and check for water tightness of the bore packing. Rate to include cleaning, placing in position pipe sleeve, application of bonding coat, preparation of Pipe sleeve, pouring of POLYCRETE-A and curing at all height sand levels etc. complete to the satisfaction of the EIC.

Nos

20



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

D. DIFFERENT TYPES OF BONDING AGENT

17. BONDING AGENT FOR C.M. PLASTER WITH RCC SURFACE

Providing and applying one pack Bonding coat between concrete members like RCC slabs, columns, beams, Chajjas, pardis etc and cement mortar plaster using HACK AID PLAST of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent Clean the concrete surface thoroughly to remove dust, dirt, grime, deshuttering oils and rub down to a clean surface. Apply HACK AID PLAST by spray on the entire concrete surface. Provide a lean cement- sand dash coat over the same. Allow the dash coat to set for around 24 hours. Further plastering as per specifications can continue. The rate to include for entire application at all heights and levels to the complete satisfaction of the EIC.

Sq.m

18. BONDING COAT FOR CONSTRUCTION JOINTS IN CONCRETE

Providing and applying acrylic based polymeric Bonding coat between concrete to concrete joint using POLYALK EP of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent in the ratio by weight to the entire concrete joint. Make sure that no area is left uncovered. The rate to include application and ensuring poring of new concrete maintaining sufficient tacky period of the bonding coat, and application at all heights etc. complete or as directed by the EIC.

Sq.m

19. BONDING AGENT FOR GYPSUM PLASTER

Providing and applying Gypsum plaster (of any standard make) to the internal walls of the surface including bonding agent HACK AID PLAST-G of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent Apply HACK AID PLAST-G by brush/ roller or spray on the surface. Provide Gypsum plaster over the same. All complete as per the satisfaction of the EIC

Sq.m

21



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

20. BONDING AGENT FOR TILE FIXING.

Providing and fixing polymerized cementitious ready to use tile adhesive for fixing of tiles using POLYALK TA of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent .Add 20% of water by weight of POLYALK TA and lay the same on the required area. Immediately place in position the tile and tamp it to position so as to remove the entrapped air and fix in position. Allow to set for 24 hours before proceeding with joint filling of the same. The rate to include for cleaning, watering the entire surface, laying and fixing in position of tiles at all levels and heights to floors, walls, dado wherever necessary etc. complete to the satisfaction of the EIC. Payment will be made as per the plan area.

Sq.m

22



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

E. VARIOUS COATINGS & APPLICATION FOR CAR PARKING AREAS

21. ANTI CARBONATION COATING

A Clean the existing surface by scrubbing so as to remove all the existing paint, dust, dirt, grime, oil etc and washing the surface clean with jet of water etc. complete to the satisfaction of the EIC.

B Providing and applying anti carbonation coating “SUNEXT-SP” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent of approved shade. Mix 1 litre of “SUNEXT-SP” with 1 L of water and use as priming coat on the surface. Mix 1 L of Sunext-8 with 100ml of water, stir well and apply by roller for subsequent two coats. The process includes erection of scaffolding at all levels, applying three coats at an interval of 24 hours between each coat curing etc. complete to the satisfaction of EIC

Sq.m

22. EPOXY COATING FOR CAR PARK AREAS

A

Clean the existing cured RCC surface so that it is free from loose particles, flakes, grease, oil etc. and make sure that the surface is dry & sound. Ensure to provide necessary crack filling treatment if any on the existing surface using epoxy mortar. Mix SUNEPOXY 378 of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent (resin and hardener in the ratio of 1:0.5 by weight) and apply by roller on the clean and dry RCC surface. Allow to air cure for 24 hours and apply similar two coats to achieve final finish. Rate includes cleaning, treatment to existing cracks, application and cleaning at all levels etc. complete to the satisfaction of the EIC

Sq. m

23



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

23. NON-METALLIC FLOOR HARDENERS

OPTION 1: DUST PROOF LIQUID FLOOR HARDENER

Providing & applying coating of SUNFLOOR METALLIN over the concrete slabs of pavements, parking lots, swimming pool decks etc. Dilute 0.5kg SUNFLOOR METALLIN in 3.5kgs of water. Use a broom or brush for ensuring uniform absorbency of liquid in the entire area. After 24 hrs. prepare a solution using 1 kg SUNFLOOR METALLIN in 3kgs of water & apply the second coat. Apply third coat after 24 hrs using 2 kgs of SUNFLOOR METALLIN in 2kgs of water. Light foot traffic may be allowed after 24 hours etc. all complete as per the satisfaction of the EIC

Sq.m

OPTION 2: DRY SHAKE FLOOR HARDENER

Providing and sprinkling synthetic, non metallic, high abrasion resistant floor hardener over the concrete slabs of pavements, parking lots, swimming pool decks etc. While the base concrete is about to set and the bleeding water appears on the surface, sprinkle POLYABRES of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent over the bleeding water @3- 5 Kg per Sqm and finish with trowel as per requirement. Allow to set for 24 hours and proceed with regular concrete curing specification. Light foot traffic may be allowed after 24 hours etc. all complete as per the satisfaction of the EIC

Sq.m

24. HYGENIC COATING FOR WATER TANKS

Clean the existing cured internal surface of the water tank so that it is free from loose particles, flakes and ensure that the surface is dry & sound. Ensure to provide necessary crack filling treatment if any on the existing surface using epoxy mortar. Mix SUNEPOXY 378 of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent (resin and hardener in the ratio of 1:0.5 by weight) and apply by roller on the clean and dry surface. Allow to air cure for 24 hours and apply similar two coats to achieve final finish. Rate includes erection of scaffolding cleaning, treatment to existing cracks, application and cleaning at all levels etc. complete to the satisfaction of the EIC

Sq.m

24



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

F. ANTI-CORROSIVE TREATMENT TO STEEL

25. RUST REMOVAL AND CONVERSION FOR STEEL

Remove loose rust from the reinforcement bars by mechanical means like wire brushing, chipping, hammering, etc. Using cotton waste swab apply “RUSTICIDE” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent. The rusted surface will turn from reddish brown to blackish non-rusted colour. After 24 hours remove the free / loose rust particles by simple dusting with brush, etc. complete to the satisfaction of the EIC. Payment will be made on the quantity of “RUSTICIDE” consumed.

Litres

26. RUST PASSIVATION OF STEEL

Prepare a lump free consistent slurry of 1 kg. of “POLYALK FIXOPRIME” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent with 1.25 kg. of fresh grey cement. Do not add any water. Apply the above slurry to the derusted steel surface by a paint brush. Allow this coat to set for 24 hours & then apply a similar second coat etc. complete to the satisfaction of the EIC. Prepare as much slurry as can be applied within 30 minutes. Payment will be made on the quantity of “POLYALK FIXOPRIME” used.

Litres

27. CORROSION PROTECTION TO STEEL WITH SACRIFICAL ANODE - SUNANODE

Providing and fixing in position zinc based sacrificial anode- SUNANODE of M/s. Sunanda Speciality Coatings Pvt. Ltd over the cleaned steel surface. Fixing to be done using anode connectors or tack welding to steel surface. The rate includes cleaning, applying, fixing in position, welding at all heights etc. complete to the satisfaction of the EIC.

Nos

25



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

28. INTEGRAL CORROSION INHIBITING ADMIXTURE FOR RCC MEMBERS

Providing and laying R.C.C. of designed grade at all heights and levels on well compacted/sound surfaces using a mechanical mixer including dewatering, shuttering, vibrating, curing and finishing as required. Admix integral corrosion inhibitor POLYALK CP293 of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent @ 1% by weight of cement. The rate to include for storage, handling, transportation of materials, equipments etc using appropriate methods etc. complete.

Cu.m

29. PU COATING FOR PROTECTION TO STRUCTURAL STEEL/ RAILINGS/ GRILLS

Clean the existing steel surface by scrubbing so as to remove al the existing loose rust etc. Using cotton waste swab apply “RUSTICIDE” of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent. After 24 hours remove the free / loose rust particles by simple dusting with brush, etc. complete to the satisfaction of the EIC. Providing and applying three coats of protective coating of SUN PUGARD of M/s. Sunanda Speciality Coatings Pvt. Ltd over the cleaned steel surface. Mix 4 parts of Part-A to 1 part of Part-B using mechanical stirrer to form uniform consistency. Apply the three coats by brush or spray at 4-6 hours interval between each coat. to the satisfaction of the EIC.

Sq. m

26



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

G. ANCHORING OF DOWEL BARS

30. ANCHORING DOWEL BARS IN RCC MEMBERS USING EPOXY GROUTS

Drilling holes in the existing RCC surface beams, columns, slabs for inserting dowel rods of stipulated size. Mixing and placing SUNEPOXY 358 of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent in the ratio ( 1 part Resin and 0.5 part Hardener) and pouring with appropriate tools in the clean drilled hole. Ensure surface is dry and free from moisture. Insert the dowel rod in position and leave un-disturbed for next 24 hours. If necessary give the packing to it. Further work to proceed after 3 days of setting time. Rate to include drilling, cleaning, placing epoxy, setting etc. all complete as per the satisfaction of the EIC Payment will be made on the quantity of “SUNEPOXY 358” consumed

Liters

31 ROCK ANCHORING

Clean the drilled hole on the rock surface and remove dust, loose particles, etc using electric blowers or suction device. Apply bonding coat of POLYALK EP of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent to the entire surface. Provide rod in place and pour high strength POLYCRETE-A of M/s. Sunanda Speciality Coatings Pvt. Ltd in the hole. POLYCRETE-A is prepared by adding 12.5- 13% water by weight of POLYCRETE-A and mixing it using mechanical stirrer to form flowable consistency, curing etc complete to the satisfaction of the EIC.

Nos

27



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

H. CURING COMPOUNDS

32. CURING COMPOUNDS

A

Clean the existing RCC and plaster surface by scrubbing so as to remove all the existing, dust, dirt, grime, oil etc and washing the surface clean with jet of water etc. complete to the satisfaction of the EIC.

B

Providing and applying one pack curing compound SUNPOLICURE of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent on the entire surface using a curing pump. Moisten the surface before the application and saturate the substrate. Immediately while the surface is damp spray SUNPOLICURE to form a uniform film over the entire surface. The rate to include for application of the same at all heights and levels etc. all complete as per the satisfaction of the EIC

Sq.m

28



A N I S O 9 0 0 1 : 2 0 0 8 C O M P A N Y

I.EPOXY FLOORING

33 EPOXY FLOORING

Clean the existing RCC and plaster surface by scrubbing so as to remove all the existing, dust, dirt, grime, etc. complete to the satisfaction of the EIC.

Providing and applying SUNEPOXY 378 of M/s. Sunanda Speciality Coatings Pvt. Ltd. or equivalent and apply by roller on the clean and dry RCC surface.

33a 1mm Self Leveling Epoxy flooring

Sq.m

33b 2mm Self Leveling Epoxy flooring

Sq.m

33c 3mm Epoxy Screed + Self Leveling Epoxy flooring

Sq.m

sunanda - sunandaglobal.com sunanda speciality coatings pvt. ltd. sunanda speciality coatings pvt....

Documents