Switch Fascia for 2017 Holden ColoradoUser Instructions

KIT CONTENTSSwitch Fascia2 x Switch Blanks (top switch locations)1 x Switch (top location)2 x Switch Adaptors (bottom locations)Instructions.

YOU WILL NEEDPhillips head screwdriverSmall blade screwdriverTrim removal tool.

PLEASE READ FULL INSTRUCTIONS BEFORE STARTING INSTALLATION.

1. REMOVE THE ORIGINAL FASCIA FROM THE VEHICLESTEP 1. Ensure the vehicle is parked in a safe location and the handbrake is fully applied. If the transmission is automatic, place in reverse (this allows for room to remove the surrounding console trim).

STEP 2. Using a plastic trim remover tool or similar, pry the trim up directly behind the gear selector (as shown) to dislodge the clips. There are four locking clips in total (two on each side). Using the trim removal tool, work around the vehicles surrounding trim to release them all. Use caution to avoid damaging trim or surround. (Refer Figure 1 & 2).

STEP 3. Lift the trim up towards the heater controls until it almost touches and then to the side to gain access to the 12V connectors located on the rear. Remove both connectors by depressing the locking tabs and pulling straight out.

Figure 1 Figure 2

STEP 4. For the Z71 model with the OEM seat heater switches, disconnect the connectors from the switches. The complete trim can now be remove from the vehicle. (Refer Figure 3).

2. REMOVE THE FASCIA AND 12V POWER SOCKETS

DO NOT TRY AND REMOVE THE COMPLETE SOCKET AND COVER AS AN ASSEMBLY

STEP 5. To remove the original fascia from the surrounding trim, remove the four Phillips screws and retain them, as they will be reused. (Refer Figure 4 & 5).

STEP 6. Open the front cover of the 12v outlet, then using a small blade screwdriver while applying slight pressure to the back, gently pry the two locking tabs away from the metal surface to remove the socket completely from the cover. (Refer Figure 6 & 7).

Figure 4 Figure 5

Figure 6 Figure 7

Figure 3

STEP 7. Now remove the black plastic surround by depressing the two tabs inwards. (Refer Figure 8 & 9).

STEP 8. Repeat the process on the other side, then remove the two white retaining clips from each end using a small blade screwdriver. (Refer Figure 10, 11,12). Warning: Wear safety glasses as the clips can flick off in any direction.

Figure 8 Figure 9

Figure 10

Figure 11 Figure 12

3. REFITTING 12V POWER SOCKETSSTEP 9. Insert front cover of the 12V power socket to the fascia, ensuring they locate with the indentation of the switch fascia and lock into place. (Refer Figure 13 & 14).

STEP 10. Fit the main body of the socket through the front cover, first ensuring correct alignment as it will only fit in one orientation. Push into place until it locks in position, repeat process for the second accessory outlet. (Refer Figure 15 & 16).

STEP 11. Refit the two white plastic retaining clips to each end of the new switch fascia, so they click into place.

Figure 15

Figure 13 Figure 14

Figure 16

4. REFITTING THE FASCIA TO THE TRIMSTEP 12. Locate the new switch fascia onto the OEM surround, using the four original screws affix the fascia to the surrounding trim. NOTE: Switches can be fitted to the fascia after it is installed, however it is recommended to fit switches before final installation.

STEP 13. Reconnect the two original 12V connectors to the back of the power sockets. (Refer Figure 17 & 18).

STEP 14. For the Z71 model with the OEM heater switches, remove the switch adaptors that are in the two lower switch locations by depressing their locking tabs on the back of the fascia. Then refit OEM heater switches into the new switch fascia by first aligning the locating lug to the corresponding groove in the switch fascia, then reconnect the two connectors. (Refer Figure 19).

NOTE: For Holden Colorado models that do not have OEM heater switches, two switch adaptors are provided for use with OEM style 70 series horizontal Toyota switches (switches not included - available as an optional accessory).

STEP 15. Align the two rear white clips on the back of the fascia against the locating points on the main console, then slowly lower into place ensuring all locating clips align in their respective mounting locations. (Refer Figure 20).

STEP 16. Ensure surrounding console is fully pushed and locked into place. (Refer Figure 21).

STEP 17. Align the two rear white clips on the back of the fascia against

Figure 17 Figure 18

Figure 20 Figure 21

Figure 19

SWITCHESA single on/off switch and two switch blanks are provided with the fascia (top locations) the blanks have been designed to accommodate the REDARC® Tow-Pro™ remote brake controller. On the back of the blanks are two corresponding indents to aid in drilling the two required holes, extra blanks are available (Part number CBSWB).

The standard switches used for the top three locations are the popular and readily available late model Toyota switch (Lightforce part numbers CBSWTY2, CBSWTY2H & Dual switch CBSWTY2D) compatible with the 200 Series Landcruiser, Prado 150 and 2015 Hilux models.

The switches used for the two bottom locations are early model Toyota switches as used in the 70 Series Landcruiser’s (horizontally fitted).

NOTE: No switches or switch blanks are supplied with the fascia for the two bottom locations. Switches sold seperately. If the switch rating at 12 volts is over three amps, a relay must be fitted.

WIRING1) Blue - 12v power in 2) Yellow - 12v switched power out 3) Blank 4) Red - from 12v dash light circuit 5) Black - To vehicles earth (negative)

For fitment of optional switches, follow wiring instructions included with the switch.

For warranty information and to register your product for warranty purposes, visit lightforce.com/warranty

LIGHTFORCE AUSTRALIA PTY LTD

11 Manton Street, Hindmarsh SA 5007 Australia

www.lightforce.com • Email: sales@lightforce.com

Australia Telephone: 08 8440 0888 | Fax: 08 8346 0504

International Telephone: +61 8 8440 0888 | Fax: +61 8 8346 0504

All logos and images are subject to relevant trademark and copyright protection LIGHTFORCE Pty Ltd. Copyright © 2017. Data and specifications contained maybe subject to change without notice.Lightforce Australia Pty Ltd shall not be liable for damage, malfunction, failure resulting from accident, misuse, misapplication, unauthorised repair, neglect, modification, unauthorised or non standard replacement parts, accessories, bulbs, batteries or voltage or operation of the product beyond its technical and or environmental specification.

171206-1-CBFASCIA2-Colorado-Fascia-Instructions