symbol 2 d ref data guide

SmartPlant 2D Symbols Reference Data Guide

Version 2011 R1 (9.1)

May 2012

DSP3D-PE-200073E

Copyright

Copyright 2006-2012 Intergraph Corporation. All Rights Reserved.

Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation.

Portions of this software are owned by Spatial Corp. 1986-2010. All Rights Reserved.

U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS 252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.

Unpublished - rights reserved under the copyright laws of the United States.

Intergraph Corporation P.O. Box 240000 Huntsville, AL 35813

Terms of Use

Use of this software product is subject to the End User License Agreement ("EULA") delivered with this software product unless the licensee has a valid signed license for this software product with Intergraph Corporation. If the licensee has a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take precedence and govern the use of this software product. Subject to the terms contained within the applicable license agreement, Intergraph Corporation gives licensee permission to print a reasonable number of copies of the documentation as defined in the applicable license agreement and delivered with the software product for licensee's internal, non-commercial use. The documentation may not be printed for resale or redistribution.

Warranties and Liabilities

All warranties given by Intergraph Corporation about equipment or software are set forth in the EULA provided with the software or applicable license for the software product signed by Intergraph Corporation, and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such warranties. Intergraph believes the information in this publication is accurate as of its publication date.

The information and the software discussed in this document are subject to change without notice and are subject to applicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.

The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of this license. No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by Intergraph or its affiliated companies. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data. Users should verify for themselves that the data is accurate and suitable for their project work.

Trademarks

Intergraph, the Intergraph logo, PDS, SmartPlant, FrameWorks, I-Convert, I-Export, I-Sketch, SmartMarine, IntelliShip, INtools, ISOGEN, MARIAN, SmartSketch, SPOOLGEN, SupportManager, and SupportModeler are trademarks or registered trademarks of Intergraph Corporation or its subsidiaries in the United States and other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation. ACIS is a registered trademark of SPATIAL TECHNOLOGY, INC. Infragistics, Presentation Layer Framework, ActiveTreeView Ctrl, ProtoViewCtl, ActiveThreed Ctrl, ActiveListBar Ctrl, ActiveSplitter, ActiveToolbars Ctrl, ActiveToolbars Plus Ctrl, and ProtoView are trademarks of Infragistics, Inc. Incorporates portions of 2D DCM, 3D DCM, and HLM by Siemens Product Lifecycle Management Software III (GB) Ltd. All rights reserved. Gigasoft is a registered trademark, and ProEssentials a trademark of Gigasoft, Inc. VideoSoft and VXFlexGrid are either registered trademarks or trademarks of ComponentOne LLC 1991-2009, All rights reserved. Oracle, JD Edwards, PeopleSoft, and Retek are registered trademarks of Oracle Corporation and/or its affiliates. Tribon is a trademark of AVEVA Group plc. Alma and act/cut are trademarks of the Alma company. Other brands and product names are trademarks of their respective owners.

SmartPlant 2D Symbols Reference Data Guide 3

Contents Preface .......................................................................................................................................................... 5

SmartPlant 3D Documentation Set ......................................................................................................... 5 Documentation Comments ..................................................................................................................... 7

What's New in 2D Symbols Reference Data ............................................................................................. 7

2D Symbols Reference Data ....................................................................................................................... 9

Member Cross Sections ............................................................................................................................ 11

Cross Section Symbol 2L ...................................................................................................................... 12 Cross Section Symbol C ....................................................................................................................... 14 Cross Section Symbol CS ..................................................................................................................... 15 Cross Section Symbol HSSC ................................................................................................................ 16 Cross Section Symbol HSSR ................................................................................................................ 17 Cross Section Symbol HW .................................................................................................................... 18 Cross Section Symbol HWWF .............................................................................................................. 19 Cross Section Symbol L ........................................................................................................................ 20 Cross Section Symbol Rect .................................................................................................................. 22 Cross Section Symbol RectC ................................................................................................................ 24 Cross Section Symbol RectCWF .......................................................................................................... 25 Cross Section Symbol RectWF ............................................................................................................. 26 Cross Section Symbol RS ..................................................................................................................... 27 Cross Section Symbol S ....................................................................................................................... 28 Cross Section Symbol ST ..................................................................................................................... 30 Cross Section Symbol T ....................................................................................................................... 31 Cross Section Symbol W ...................................................................................................................... 33 Cross Section Symbol Wedge .............................................................................................................. 35 Cross Section Symbol WedgeWF ......................................................................................................... 36

Index ........................................................................................................................................................... 39

Contents

4 SmartPlant 2D Symbols Reference Data Guide


This document is a reference data guide for the SmartPlant 3D 2D Symbols task. The purpose of this document is to describe the reference data delivered with the software for this task.

Reference data includes both catalog data and specification data. Catalog data includes the parts that you place in the model, such as piping components and equipment. Specification data includes the rules that govern how those parts are placed and connected.

SmartPlant 3D Documentation Set SmartPlant 3D documentation is available as Adobe PDF files. The content is the same as online Help. To access these PDF documents, click Help > Printable Guides in the software.

The documentation set is divided into four categories:

Administrative guides contain information about installing, configuring, customizing, and troubleshooting SmartPlant 3D.

User's guides provide command reference and how-to information for working in each SmartPlant 3D task.

Reference data guides define the reference data workbooks. Not all tasks have reference data.

ISOGEN guides

Administrative Guides

SmartPlant 3D Installation Guide - Provides instructions on installing and configuring the software.

Project Management User's Guide - Provides instructions for setting up the databases, creating permission groups, backing up and restoring project data, assigning access permissions to the model, defining and managing locations for Global Workshare, and version migration.

SmartPlant 3D Global Workshare Guide - Provides instructions for setting up the software and the databases to work in a workshare environment.

SmartPlant 3D Interference Checking Guide - Provides information on installing, configuring, and using the interference detection service.

SmartPlant 3D Integration Reference Guide - Provides information about installing, configuring, and using SmartPlant 3D in an integrated environment.

SmartPlant 3D Interpreting Human Piping Specifications - Provides information about how to interpret human piping specifications so that you can create the corresponding piping specification in the software.

SmartPlant 3D Export to PDMS - Provides information about how to export model data from SmartPlant 3D to PDMS. Specific guidelines relating to best practices and known limitations of the export functionality are also included.

SmartPlant 3D Point Cloud Reference - Provides information for referencing point cloud files provided by point cloud vendors in SmartPlant 3D.

SmartPlant 3D Troubleshooting Guide - Provides information on how to resolve errors that you may encounter in the software by documenting troubleshooting tips, error messages, and To Do List messages.

SmartPlant 3D Plant Design System (PDS) Guide - Provides all information needed to use PDS with SmartPlant 3D. Topics include referencing active PDS projects in SmartPlant 3D, exporting

Preface

Preface


PDS data and importing that data into SmartPlant 3D, and converting PDS reference data to SmartPlant 3D reference data.

SmartPlant 3D/SmartMarine 3D Programmer's Guide - Provides information about custom commands, naming rules, and symbol programming. This document is delivered, if you install the Programming Resources, to the [Product Folder]\3D\Programming\Help folder.

User's Guides

Catalog User's Guide - Provides information about viewing, editing, and creating reference data and select lists (codelists).

Common User's Guide - Provides information about defining workspaces, manipulating views, and running reports.

Electrical User's Guide - Provides information about routing electrical cable, cableway, cable tray, and conduit.

Equipment and Furnishings User's Guide - Provides information about placing equipment.

Grids User's Guide - Provides instructions for creating coordinate systems, elevation grid planes, vertical grid planes, radial cylinders, radial planes, grid arcs, and grid lines.

Hangers and Supports User's Guide - Provides instructions on placing piping, duct, and cableway supports in the model.

HVAC User's Guide - Provides instructions for routing HVAC duct.

Orthographic Drawings User's Guide - Provides information about creating and managing orthographic drawings.

Piping Isometric Drawings User's Guide - Provides information about creating and managing piping isometric drawings.

Piping User's Guide - Provides instructions for routing pipe and placing valves, taps, and pipe joints.

Reports User's Guide - Provides information about creating and managing spreadsheet reports.

Space Management User's Guide - Provides instructions for placing space objects such as areas, zones, interference volumes, and drawing volumes in the model.

Structural Analysis User's Guide - Provides instructions for defining loads, load cases, load combinations, and the importing and exporting of analytical data.

Structure User's Guide - Provides instructions for placing structural members such as: beams, columns, slabs, openings, stairs, ladders, equipment foundations, and handrails.

Systems and Specifications User's Guide - Provides instructions for creating systems and selecting which specifications are available for each system type.

Reference Data Guides

SmartPlant 3D 2D Symbols User's Guide - Provides command reference information and procedural instructions for creating 2D symbols used to represent collars, clips, profiles, brackets, and other items.

SmartPlant 3D 2D Symbols Reference Data Guide - Provides information about the two-dimensional symbols used in all tasks.

Drawings and Reports Reference Data Guide - Provides information about reports reference data.

Electrical Reference Data Guide - Provides information about electrical cable, cableway, cable tray, and conduit reference data.

Electrical 3D Symbols Reference - Provides information about the cable tray and conduit 3D symbols that are available.

Preface


Equipment and Furnishings Reference Data Guide - Provides information about equipment reference data.

Equipment 3D Symbols Reference - Provides information about the equipment, equipment component, design shapes, and design aides 3D symbols that are available.

Hangers and Supports Reference Data Guide - Provides information about hangers and supports reference data.

Hangers and Supports 3D Symbols Reference - Provides information about the hanger and support 3D symbols that are available.

Hangers and Supports SmartPart Symbols Reference - Provides information about the hanger and support SmartPart symbols that are available.

HVAC Reference Data Guide - Provides information about HVAC reference data.

HVAC 3D Symbols Reference - Provides information about the HVAC 3D symbols that are available.

SmartPlant 3D Reference Data Guide - Provides instructions about the Bulkload utility, codelists, and the reference data common to several disciplines.

Piping Reference Data Guide - Provides information about piping reference data including piping specifications, piping specification rules, piping parts, and piping symbols.

Piping 3D Symbols Reference - Provides information about the piping 3D symbols that are available.

Space Management Reference Data Guide - Provides information about space management reference data.

Structure Reference Data Guide - Provides information about structural reference data.

Structure 3D Symbols Reference - Provides information about the stair, ladder, footings, and equipment foundation 3D symbols that are available.

ISOGEN Guides

Symbol Keys Reference Guide - Provides information about the symbol keys for isometric drawings. This guide is from Alias, the makers of ISOGEN.

Documentation Comments We welcome comments or suggestions about this documentation. You can send us an email at: [email protected].

Documentation updates for supported software versions are available from eCustomer https://crmweb.intergraph.com.

What's New in 2D Symbols Reference Data The following changes have been made to the 2D symbols reference data.

Version 2011 R1 (9.1)

Preface



S E C T I O N 1

The 2D Symbols utility is delivered with the software and is used to create symbols and facilitate using these symbols in a modeling environment.

This document describes all of the 2D symbols that are delivered with the software. The symbol library is delivered to the SharedContent share in the [Reference Data Product Directory]\SharedContent folder

You can create your own custom symbols using the 2D Symbols utility. To learn how to create 2D symbols, refer to the SmartPlant 3D 2D Symbols User's Guide.

2D Symbols Reference Data

2D Symbols Reference Data



S E C T I O N 2

All section tables delivered with the software use a specific set of cross-section symbols. Some section tables use all the cross-section symbols in the set; some tables only use a subset of the cross-section symbols. Each cross-section symbol has its own set of properties. When looking at a section table workbook, you can determine the cross-section symbol that is being referenced by that particular sheet by looking at the SymbolDefinition entry at the top of the sheet.

The cross-section symbols are delivered with the Reference Data software in the [Reference Data Folder]\SharedContent\CrossSections folder. You can create your own custom cross-section symbols, sometimes referred to as arbitrary sections, using the 2D Symbols utility that is delivered with the software.

The software always uses the simple physical aspect of the cross-section symbol to display the member geometry in the model. The detailed physical aspect is not used or required. In addition, the software uses the simple physical aspect shape to calculate the volume and surface of the member. Therefore, for more accurate calculations, consider including fillets in your simple physical aspect.

In This Section Cross Section Symbol 2L .............................................................. 12 Cross Section Symbol C ................................................................ 14 Cross Section Symbol CS ............................................................. 15 Cross Section Symbol HSSC ........................................................ 16 Cross Section Symbol HSSR ........................................................ 17 Cross Section Symbol HW ............................................................ 18 Cross Section Symbol HWWF ....................................................... 19 Cross Section Symbol L ................................................................ 20 Cross Section Symbol Rect ........................................................... 22 Cross Section Symbol RectC ........................................................ 24 Cross Section Symbol RectCWF ................................................... 25 Cross Section Symbol RectWF ..................................................... 26 Cross Section Symbol RS ............................................................. 27 Cross Section Symbol S ................................................................ 28 Cross Section Symbol ST .............................................................. 30 Cross Section Symbol T ................................................................ 31 Cross Section Symbol W ............................................................... 33 Cross Section Symbol Wedge ....................................................... 35 Cross Section Symbol WedgeWF ................................................. 36

Member Cross Sections



Cross Section Symbol 2L The 2L cross section symbol defines double-angle sections and uses the following properties.

Section Name - Type the section name. This name appears when you label members. The section name must be unique across the catalog.

Short Name - Type the short name for the section.

EDI Name - Type the Electronic Data Interchange name for the section. This name is used when translating sections through CIMsteel. This property is currently not used.

Group Id - Type the material group identification for the section.

Unit Weight - Type the weight of the section. The unit weight is defined in mass per length, pound per foot (lb/ft).

Area - Type the cross-sectional area for the section. The area is defined in square inches or square millimeters.

Depth - Type the depth for the section (longer legs). The depth is defined in inches or millimeters.

d - Type the other depth for the section (shorter legs). The depth is defined in inches or millimeters.

bf - Type the width of a single angle. The width is defined in inches or millimeters.

Width - Type the width of the entire section. The width is defined in inches or millimeters.

Perimeter - Type the outside perimeter of the section.

tf - Type the flange thickness for the section. The thickness is defined in inches or millimeters.

tw - Type the web thickness for the section. The thickness is defined in inches or millimeters.

kdesign - Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape or the equivalent distance on the welded section.

kdetail - Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape or the equivalent distance on welded section.

bb - Enter the back-to-back spacing on the section.

CentroidY - Type the centroid location along the y-axis. The location is defined in inches or millimeters.

Ixx - Type the moment of inertia for the section's local x-axis.

Zxx - Type the plastic section modulus for the section's local x-axis.

Sxx - Type the section modulus for the section's local x-axis.

Rxx - Type the radius of gyration for the section's local x-axis.

Ryy - Type the radius of gyration for the section's local y-axis.

ro - Type the polar radius of gyration about the shear center.

H - Type the flexural constant.



bb Configuration - Specifies which legs of the angles are placed back-to-back. Type 0 for equal leg angle. Type 1 to place the long legs back-to-back. Type 2 to place the short legs back-to-back.

lsg - Specify the bolt gage for the long side when there is one bolt row. For more information, see Member Cross Sections.

lsg1 - Specify the gage distance to the first bolt row on the long side when there are two bolt rows.

lsg2 - Specify the gage distance between the first and second bolt rows on the long side when there are two bolt rows.

ssg - Specify the bolt gage for the short side when there is one bolt row.

ssg1 - Specify the gage distance to the first bolt row on the short side when there are two bolt rows.

ssg2 - Specify the gage distance from the first bolt row to the second bolt row on the short side when there are two bolt rows.

IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is False.

IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the default value is False.

IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the default value is True.



Cross Section Symbol C The C cross section symbol defines channel sections and uses the following properties.





Unit Weight - Type the weight of the section. The unit weight is defined in mass per length pound per foot (lbm/ft).


Depth - Type the depth for the section. The depth is defined in inches or millimeters.

Width - Type the flange width for the section. The width is defined in inches or millimeters.

Perimeter - The outside perimeter distance for the section.

d - Type the depth for the section. The depth is defined in inches or millimeters.

bf - Type the flange width for the section. The width is defined in inches or millimeters.



kdesign - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled shape or the equivalent distance on the welded section.

kdetail - Type the distance from the outer face of the flange to the web toe of the fillet of the rolled shape or the equivalent distance on welded section.

CentroidX - Type the centroid location along the x-axis. The location is defined in inches or millimeters.

eo_x - Type the shear center location along the x-axis. The location is defined in inches or millimeters.

xp - Type the horizontal distance from the designated edge of member to its plastic neutral axis (PNA). The distance is defined in inches or millimeters.







Iyy - Type the moment of inertia for the section's local y-axis.

Zyy - Type the plastic section modulus for the section's local y-axis.

Syy - Type the section modulus for the section's local y-axis.


J - Type the torsional moment of inertia for the section.

Cw - Type the warping constant for the section.


H - Type the flexural constant in LRFD Specification Equation E3-1.

gf - Type the bolt gage for the flange.

gw - Type the bolt gage for the web.


IsSymmetricAlongX - Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the default value is True.

IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the default value is False.

Cross Section Symbol CS The CS cross section symbol defines solid round sections and uses the following properties.







Depth - Type the depth of the section.



Width - Type the width of the section.

Perimeter - Type the outside perimeter distance for the section.







H - Type the flexural constant.




Cross Section Symbol HSSC The HSSC cross section symbol defines circular, hollow structural sections and uses the following properties.

Section Name - Type the section name. This name appears when labeling members. The section name must be unique across the catalog.





Area - Type the cross-section area for the section. The area is defined in square inches or square millimeters.

Depth - Type the depth of the section.

Width - Type the width of the section.


tnom - Type the nominal wall thickness of the section.

tdes - Type the design wall thickness of the section.

D_t - Type the ratio of the diameter to the thickness.












IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is True.



Cross Section Symbol HSSR The HSSR cross section symbol defines rectangular, hollow, structural sections and uses the following properties.






Area - Type the cross-section area for the section. The area is defined in square inches and square millimeters.

Depth - Type the overall depth of the section.

Width - Type the width for the section. The width is defined in inches or millimeters.


tnom - Type the nominal wall thickness of the section.

tdes - Type the design wall thickness of the section.

b_t - Type the width to thickness ratio of the section.

h_t - Type the height to thickness ratio of the section.












IsHollow - Specify if the cross-section is hollow or not. For this cross-section, the default value is True.



Cross Section Symbol HW The HW symbol uses the following properties.

Section Name - Type the section name. The section name must be unique across the catalog.




Angle - Define the angle.


Area - Type the cross-section area for the section.

Depth - Type the depth for the section. The depth is defined in meters

Width - Type the width for the section. The width is defined in meters.




d - Type the depth for the section.

bf - Type the width for the section.

tw - Type the web thickness for the section. The thickness is defined in meters.

tf - Type the flange thickness for the section. The thickness is defined in meters.



CentroidY - Type the vertical distance from designated member edge to the centroidal axis.












H - Type the flexural constant for the section.

Cross Section Symbol HWWF The HWWF symbol uses the following properties.








Flange Right Width - Define the flange width on the right side.

Flange Left Width - Define the flange width on the left side.












CentroidX - Type the horizontal distance from the designated member edge to the centroidal axis.

CentroidY - Type the vertical distance from the designated member edge to the centroidal axis.













Cross Section Symbol L The L cross section symbol uses the following properties.








Area - Type the cross-section area for the section. The area is defined in square inches or square millimeters.


Width - Type the breadth for the section. The breadth is defined in inches or millimeters.


d - Type the overall depth (longer leg) for the section. The depth is defined in inches or millimeters.

bf - Type the overall width (shorter leg) for the section. The width is defined in inches or millimeters.





CentroidX - Type the location of the centroid along the local x-axis. The location is defined in inches or millimeters.

CentroidY - Type the location of the centroid along the local y-axis. The location is defined in inches or millimeters.

xp - Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along the local x-axis.

yp - Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along the local y-axis.









Rxy - Type the radius of gyration about the local z-axis. The radius is defined in inches or millimeters.





lsg - Specify the bolt gage for the long side when there is one bolt row.



lsg1 - Specify the gage distance to the first bolt row on the long side when there are two bolt rows.

lsg2 - Specify the gage distance from the first bolt row to the second bolt row on the long side when there are two bolt rows.

ssg - Specify the bolt gage for the short side when there is one bolt row.

ssg1 - Specify the gage distance to the first bolt row on the short side when there are two bolt rows.

ssg2 - Specify the gage distance from the first bolt row to the second bolt row on the short side when there are two bolt rows.



IsSymmetricAlongY - Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the default value is False.

Cross Section Symbol Rect The Rect symbol uses the following properties.







Cross Section Symbol RectC The RectC symbol uses the following properties.






Setback - Define the setback. This value is defined in meters.




























Cross Section Symbol RectCWF The RectCWF symbol uses the following properties.






Setback - Define the setback. This value is defined in meters.

Flange Right Width - Define the flange width on the right side. This valve is defined in meters.

Flange Left Width - Define the flange width on the left side. This valve is defined in meters.




























Cross Section Symbol RectWF The RectWF symbol uses the following properties.







Flange Right Width - Define the flange width on the right side. This valve is defined in meters.

Flange Left Width - Define the flange width on the left side. This valve is defined in meters.

























Cross Section Symbol RS The RS cross section symbol defines rectangular solids and uses the following properties.








Area - Type the cross-section area for the section. The area is defined in square inches and square millimeters.


Width - Type the breadth for the section. The breadth is defined in inches or millimeters.

Perimeter - Type the outside perimeter distance for the section.











Cross Section Symbol S The S cross section symbol uses the following properties.









Depth - Type the depth for the section. The depth is defined in inches.

Width - Type the flange width for the section. The width is defined in inches.


d - Type the overall depth for the section.

bf - Type the overall width for the section.

tw - Type the web thickness for the section. The thickness is defined in inches.

tf - Type the flange thickness for the section. The thickness is defined in inches.



Fy3p - Type the maximum yield for the compact web for the section.











Wno - Type the normalized warping function. The function is defined in square inches or square millimeters.

Sw - Type the warping statical moment. The moment is defined in in4 or mm4.

Qf - Type the first moment of area for the flange.

Qw - Type the first moment of area for the web.








Cross Section Symbol ST The ST cross section symbol uses the following properties.
















CentroidY - Type the distance to the centroid along the local y-axis. This distance is defined in inches or millimeters.

yp - Type the distance from the designated edge of angle to its plastic neutral axis along the local y-axis.




















Cross Section Symbol T The T cross section symbols uses the following properties.



















yp - Type the distance from designated edge of angle to its plastic neutral axis along the local y-axis.




















Cross Section Symbol W The W symbol uses the following properties.



Alternate EDI Name - Type the Electronic Data Interchange name for the section. This name is used when translating sections through CIMsteel. This property is currently not used.













Fy3p - Type the maximum yield stress for the section.











Wno - Type the normalized warping function. The function is defined in square inches or square millimeters.



Sw - Type the warping statical moment. The moment is defined in in4 or mm4.

Qf - Type the first moment of area for the flange.

Qw - Type the first moment of area for the web.








Cross Section Symbol Wedge The Wedge symbol uses the following properties.





Angle Right - Define the angle on the right side of the web.

Angle Left - Define the angle on the left side of the web.




























Cross Section Symbol WedgeWF The WedgeWF symbol uses the following properties.





Angle Right - Define the angle on the right side of the web.

Angle Left - Define the angle on the left side of the web.

Flange Right Width - Define the flange width on the right side.

Flange Left Width - Define the flange width on the left side.







2 2D Symbols Reference Data 15

C Cross Section Symbol 2L 18 Cross Section Symbol C 20 Cross Section Symbol CS 21 Cross Section Symbol HSSC 22 Cross Section Symbol HSSR 23 Cross Section Symbol HW 24 Cross Section Symbol HWWF 25 Cross Section Symbol L 27 Cross Section Symbol Rect 29 Cross Section Symbol RectC 30 Cross Section Symbol RectCWF 31 Cross Section Symbol RectWF 32 Cross Section Symbol RS 34 Cross Section Symbol S 35 Cross Section Symbol ST 36 Cross Section Symbol T 38 Cross Section Symbol W 39 Cross Section Symbol Wedge 41 Cross Section Symbol WedgeWF 42

D Documentation Comments 11

M Member Cross Sections 17

P Preface 5

S SmartPlant 3D Documentation Set 7

W What's New in 2D Symbols Reference Data

13

Index

PrefaceSmartPlant 3D Documentation SetDocumentation CommentsWhat's New in 2D Symbols Reference Data

2D Symbols Reference DataMember Cross SectionsCross Section Symbol 2LCross Section Symbol CCross Section Symbol CSCross Section Symbol HSSCCross Section Symbol HSSRCross Section Symbol HWCross Section Symbol HWWFCross Section Symbol LCross Section Symbol RectCross Section Symbol RectCCross Section Symbol RectCWFCross Section Symbol RectWFCross Section Symbol RSCross Section Symbol SCross Section Symbol STCross Section Symbol TCross Section Symbol WCross Section Symbol WedgeCross Section Symbol WedgeWF

Index

symbol 2 d ref data guide

Documents