system bathroom soleo - lixil

SOLEO

User’s Manual

System Bathroom

Thank you for purchasing this INAXproduct.In order to keep this system bathroomclean and comfortable, read this User’sManual thoroughly and get a ful lunderstanding how to use the productcorrectly and safely.

Observe all the cautions provided in this User’s Manual. Note

that the company is not responsible for any accident occured

due to improper use of this product.

* Keep this User’s Manual with the User’s Manual for

plumbing fixtures and other equipment in a place where it

can be accessed easily when needed.

* If ownership of this product is transferred, pass this User’s

Manual on to the new owner.

To the installerMake sure this User’s Manual is given to the productowener.

Warranty Certificate Attached

* For the corresponding product number, see the back of this page.

ソレオ_表1_E 07.1.17 3:36 PM ページ1

Check the control and product numbers for service. These numbers are on the control number sticker on the upper right corner of the door.

Part Number

■ How to Read Part Numbers

BY - 1418 T A UDU1 2 3 4 5

■ How to Find the Product Number

Constructor’s sticker Control number sticker(upper right of door frame)

000000000/00000000000-00000000+000000

販売店または（株）INAXメンテナンス 0120　1794　11

修理のご依頼

Upper number:Control number

Lower number:Product number

1 BY=SOLEO series

2 Unit size 121612181316131713181416141714181516151816181620171817201822

3 Wall panel T=Tile panelL=L panelS=Steel make-up panel

4 Floor specification A=Tile finishB=FRP mosaic pattern

5 Type GUU =GUU typeGTU =GTU typeUDU =UDU typeSSU =SSU typeSDU =SDU typeEFU =EFU typePEU =PEU typeUXU =UXU type

ソレオ_目次～P07_E 07.1.17 3:39 PM ページ1

Part Name...................................................................................................................1

User’s Manual for the Auxiliary Equipment.............................................................2

Safety Cautions......................................................................................................... 3

Taking a Bath .............................................................................................................6

Precautions ................................................................................................................7

Use Method ................................................................................................................8

Filling the Bathtub with Hot Water....................................................................8

Using Hot Water in the Washing Area ............................................................14

Opening and Closing the Door .......................................................................26

Using the Fixtures ............................................................................................38

Cleaning Methods....................................................................................................50

About Cleaning.................................................................................................50

Cleaning around the Bathtub ..........................................................................55

Cleaning the Wall, Floor, and Ceiling .............................................................58

Cleaning the Mirror...........................................................................................65

Cleaning the Accessories................................................................................66

Cleaning the Faucet .........................................................................................69

Cleaning the Door ............................................................................................80

Cleaning and Replacing Lights.......................................................................83

Cleaning the Ventilator Fan and Heater..........................................................91

Removing the Ceiling Inspection Door for Maintenance..............................96

Troubleshooting .................................................................................................... 97

Replacement Parts Guide .....................................................................................100

After-sales Service .............................................................................................. 102

Bathtub Size...........................................................................................................104

Warranty Certificate...............................................................................................106

Contents

ソレオ_目次～P07_E 07.1.17 3:39 PM ページ2

1

PartN

ame

■ Part Names and their Instruction Pages

* The drawing shows one example of a combination of parts. Your combination may be different, or youmay not have some of these parts.

Part Name

Shower

Ceiling inspection doorHow to remove the ceiling inspection door ➝ P.96

CeilingCleaning methods ➝ P.61

Use method ➝ P.39Cleaning methods ➝ P.92

Ventilator fan

Use method ➝ P.42Cleaning method ➝ P.93

Heater


Mirror

Bathtub and bathtub lidUse method ➝ P.39Cleaning methods ➝ P.55

Flat shelves

WallCleaning methods ➝ P.58

FloorCleaning methods ➝ P.59

Floor drain trapCleaning methods ➝ P.61



Bathtub faucetUse method ➝ P.11Cleaning methods ➝ P.69

Use method ➝ P.47


Washing area faucet

Door

Cleaning under the bathtub ➝ P.63

Apron

Laundry pipe

Slide barUse method ➝ P.40Cleaning methods ➝ P.66

Cleaning methods ➝ P.65

LightsCleaning methods ➝ P.83

ソレオ_目次～P07_E 07.1.17 3:39 PM ページ1

2

User’s

Manualfor

theA

uxiliaryE

quipment

■ For the Following Products, Read the User’s Manual for EachProduct. The Code in ( ) Corresponds with the User’s Manual forEach Product* Improper use could cause accidents and product breakage. Read the cautions and use the product

correctly.* This drawing shows one example of a combination of the products. Your combination may be different,

or you may not have some of these products.

User’s Manual for the Auxiliary Equipment

Bathroom televisionWide Type 7 (GPU-0195)Type 10 (GPU-0167)

(GPU-0186)

Sound system(GPU-0175)

Shower de Bath (GPU-0164)

Aqua-jet (GPU-0174)

Healing light II (GPU-0151)

Bathwater forlaundry system

(GPU-0156)

Bathtub faucet (➝ P.11)

Washing area faucet (➝ P.14)

Reheating fixture

Ventilator fanHeater(➝ P.39, P.42)

Light dimmer controller (GPU-0150)

ソレオ_目次～P07_E 07.1.24 9:57 AM ページ2

3

Safety

Cautions

(Make

sureto

followthe

instructionsbelow

)

Safety Cautions (Make sure to follow the instructions below)

Before use, read the safety cautions thoroughly in order to use this product safely.Failing to observe the cautions shown here could result in serious consequences.All these cautions are important for safety. Observe them at all times.* Read the User’s Manual for the auxiliary equipment used with this product, such as faucet fixtures,

ventilator fan and aqua-jet, and observe the precautions on the labels affixed to them.

● The degree of injury or damage resulting from improper use is categorized by the following signalwords. Their meanings are as follows.

This shows that there is a possibility of death or severe injury.

This shows that there is a possibility of personal injury or property damage only.

Warning

Caution

■ Signal Words

● The alert symbols indicate following meanings.

“Caution!” (This symbol urges caution. It is used with the above “Warning” and “Caution.” Make sureto read and follow the rules and the instructions.)

“Prohibited!” (Used for general prohibited actions.)

“Do not disassemble!”

“Do not touch the indicated area!”

“Follow the instructions!” (Used for general instructions.)

■ Safety Alert Symbols

● Do not disassemble, repair or remodel

● Bathtub lid

Do not disassemble, repair, or remodel.* There is a danger of electric shock or

product breakage.

Follow the User’s Manual for each auxiliaryequipment such as faucets and ventilatorfan.* There is a danger of burns, electric

shock, injuries or product breakagefrom incorrect use.

Warnings

● Handling the faucet, ventilator fan, etc.

Do not use the light fixtures, the ventilatorfan or any other electrical product with theglobe, louver or other cover removed, anddo not splash them directly with water.* There is a danger of fire, electric

shock, product or the light bulbbreakage or injuries.

● Lights and ventilator fan

Do not hang towels and other object on thelight fixtures.* They could overheat and cause fire.

When maintaining the ventilator fan orother equipment or replacing the lightbulbs, turn off (switch off) the power first.* There is a danger of electric shock or

injuries.

● Aqua-jet•Do not use with the safety cover or filter

removed or damaged.•When using, do not block the intake hole

or jet port.•Do not go underwater in the bathtub.•Do not operate the Aqua-jet while

children are taking a bath by themselves.* There is a danger of drowning or injuries

if hair or other part of the body get caught.

GlobeDo not place heavy objects nor get on topof the bathtub lid.* Doing so could cause the lid to come

off, and could result in an injuries orburns.

ソレオ_目次～P07_E 07.1.17 3:39 PM ページ3

4

Safety

Cautions

(Make

sureto

followthe

instructionsbelow

)

Check the bathtub drain is completelyplugged in.If the drain core was removed for cleaningor other reasons, make sure it is properlyinserted. (see page 56)Also, when using the reheating function, fillwater at least 10cm above the circulationport.* When using the reheating function, if the

drain is improperly plugged, it couldcause fire or product breakage.

● Filling the bathtub with hot water


● Bathing babies or the physically disabledDo not have babies or the physicallydisabled take a bath by themselves.* There is a danger of drowing, injuries

or burns.

Warnings

● Do not allow children to play by themselvesDo not let children play by themselves inthe bathroom.* There is a danger of drowing, injuries

or burns.

● Injuries and burnsDo not remove the louver and touch thefan or heater, or insert a finger or otherobjects such as sticks in it while theventilator fan is running.* Doing so could cause electric shock,

injuries or product breakage.

Do not jump into the bathtub or applyundue force on it.* Doing so could damage the bathtub,

causing injuries or water leakage.

Do not splash hot or cold water on themirror.* Sudden changes in temperature could

cause the mirror breakage, and causeinjuries.

Do not open the ceiling inspection dooror place any objects inside except whenchecking the equipment.* Doing so could cause fire, electric

shock or water leakage. The inspectiondoor could fall off, resulting in injuries.

Avoid shocks to the mirror, wall, or lightcover, such as striking objects againstthem.* Doing so could scratch or crack the

surface, causing injuries.

Do not stand on or sit onthe bathtub or counter.* There is a danger of

injuries by falling off.

Wear protective rubber doing gloves whencleaning or doing maintenance.* There is a danger of injuries from gaps,

projections, etc.

Do not put fragile objects such as glasscontainers on high flat shelves.* There is a danger of injuries by

dropping and breaking these objects.

Do not shock or apply undue force on theceiling inspection door.* There is a danger that the ceil ing

inspection door gets cracked and fall off,causing injuries.

Do not place feet on the reheatingfunction circulation port.* There is a danger that the reheating

function circulation port comes off,causing falling, injuries or burns.

When using the slide bar, do not strike theslide hook on the mirror or wall.* Doing so could scratch the side hook or

wall or crack the mirror, causinginjuries.

Caution

Do not apply undue force on the showerhead or shower hook.* There is a danger of product breakage or

injuries.

Inside the bathroom, the floor could beslippery with soap. Watch your steps anddo not run.* There is a danger of injuries by slipping

and falling.

Use the bathtub lid that fits the bathtub.* There is a danger of injuries or burns

with the bathtub lid falling off.

Do not strike or apply undue force on theapron.* There is a danger of injuries with the

cracked apron falling off.

Do not drop or knock the shower head.* There is a danger of injuries by the

cracked shower head.* There is a danger of injuries by the

cracked or scratched tiles.

ソレオ_目次～P07_E 07.1.24 9:57 AM ページ4

5

Safety

Cautions

(Make

sureto

followthe

instructionsbelow

)


● Do not install parts yourself

● Be careful of solvents and chemicals

Do not use if the floordrain cover is off orimproperly installed.Correctly insert the floordrain cover before use.* There is a danger of

injuries by tripping overthe cover.

When changing fixture locations, orinstalling new parts, contact the retail shopwhere you purchased the bathroom.* Improper installation can cause

unexpected accidents or water leakage.If hand grip bars in or out of the bathbecome unsteady, or other attachmentsbecome loose, contact the retail shopwhere you purchased the bathroom.* There is a danger of injuries or

product breakage with unrepairedproducts.

Do not attempt to make holes in the walland mount hand grips or towel rods, etc.yourself.* This can cause water leakage.

Do not pour solvents and chemicals suchas paint thinner down the drain.* Doing so could cause water leakage.

● Injuries and burns

● Be careful not to scratch the joint sealerGrout (or caulking) is used on the joints inthe floor, walls, ceiling, window frame,etc. Do not peal it off or scratch it.* Doing so could cause water leakage.

Do not use bath additives which are sulfur-based, acidic, or alkali-based. Also, do notuse bath additives which do not easilydissolve in hot water, liquid bath additiveswhich contain solvents, hot spring water,or well water (except for water whichmeets water quality standards for drinkingwater as specified in the Water SupplyLaw).* Doing so could cause discoloration of

the bathtub surface, damaged sealsand grout, and water leakage.

Caution

If chemicals such as make-up or aromaticoils are spilled, wash them off with waterimmediately and completely.* If chemicals are left adhering to the

surface, they could cause waterleakage, discoloration, and cracks.

Do not use or bring solid or powderedchlorine cleansers, or bleach nearby.* Doing so could cause metal and

rubber to corrode and deteriorate,leading to water leakage.

● Do not apply undue forceDo not place heavy objects on the windowframe such as flower pots. Do not exertforce on the window frame by installingextendable blind and so on.* Doing so could cause product

breakage or water leakage.

Do not stand on or sit onthe counter.* Doing so could cause

product breakage orwater leakage.

If the bath is not used for an extendedperiod of time and the temperature insidethe bathroom drops below zero, removethe water out of the drain trap and fill theantifreeze to prevent pipes from freezing. Ifyou cannot the acquire the antifreeze, takeout the hair catcher and odor preventionpipe and place a rag in the drain. This willprevent any bad odors from escaping intothe room from the drain.* There is a danger of product breakage

and water leakage by frozen water inthe trap.

Do not apply undue force on the storagerack.* There is a danger of product breakage

or injuries.

● While there is a danger of winter freezing

The following people must not use aqua-jet. People who are pregnant, physicallyweak, chronically ill or under the influenceof alcohol or sleeping pills or with heartconditions. * There is a danger of medical problems

arising.

Do not use aqua-jet for more than 15minutes.* There is a danger of straining the heart.

● About use of aqua-jet

Be careful not to hityour head on thebeamed ceiling.* There is a danger

of injuries with thecorner of the beam.

● Be careful of the beamed ceiling

When enteringand leaving thebathtub, alwaysuse the step. Donot jump off thestep. Also, do notstand on or sit onthe middle of thebathtub rim.* There is a danger of injuries by falling

off.

Do not use bath additives in the widebathtub.* There is a danger of injuries by missing

the step with unclear water.

● About the wide bathtub

Beamed Ceiling

ソレオ_目次～P07_E 07.1.24 9:57 AM ページ5

6

Takinga

Bath

Beforetaking a

bath

While takinga bath

After takinga bath

1 2 3

By using a water wiper orabsorbent car washingtowel, you can quicklyremove bathroommoisture and thebathroom dries quickly.

Relax and relieve fatigue with a foot bath, lower bodybath, or full relaxing bath.For a relieving bath, read this manual and use it correctly.

If you rinse off the entire bathroom with the shower, cleaning becomes easy.

Read the separatemanual for the waterheater to adjust thetemperature and otheruse methods.

Set the Hot Water Temperature onthe Water Heater

Placing the bathtub lidmakes the water coolmore slowly.

When You Leave WarmBathwater for the Next Person

To prevent humidity,place the bathtub lid, andrun the ventilator fan oropen the window toprovide as muchventilation as possibleuntil the next morning. Itis even more effective ifyou lightly wipe moistureoff the floor, counter, etc.

If Warm Bathwater is LeftUntil the Next Morning

Remove the water. Readfrom page 76 of thismanual.

If Air Temperature is Low, and thereis a Danger of Frozen Water Pipes

Shut the Drain Plug

Taking a Bath

If a heater is equipted, theentire bathroom can beheated by turning on theheater about 30 to 60minutes before getting inthe bath in the winter.

ONE POINT

Read page 8 of thismanual.

Fill the Tub with hotwater

To remove the door fromoutside the bathroom inan emergency, read themanual starting from page32.

How to Remove theDoor in an Emergency

Run the ventilator fan oropen the window toprovide as muchventilation as possibleuntil the next morning. Itis even more effective ifyou lightly wipe moistureoff the floor, counter, etc.

When You Drain WarmBathwater

Neat Trick

ソレオ_目次～P07_E 07.1.17 3:40 PM ページ6

7

Precautions

Precautions

Do not drop heavy or hard objects.* Doing so could crack or chip the floor.

Do not leave items like hair pins or razor bladesfor a long time.* Rust could stick on the surface, which may

not be removed.

Do not bring flames, cigarettes, etc. nearby.* Doing so could cause marks or cracks.

After using a bathmat, bamboo floor covering,etc. in the washing area, wash it with water andstand it against the wall.* Not doing so could result in mold,

discoloration, or bad odor.

Do not install a bathwater purifier with reheatingfunction (24-hour bath) in the bathtub, except forIdeatone bathtubs. Even in an Ideatone bathtub,do not install ozone disinfection type of bathtubpurifier with reheating function (24-hour bath).* If used continually, i t could accelerate

wearing or color fading of the bathtubsurface.

When using hair dye or nail polish remover insidethe bathroom, spread a sheet underneath toprotect the floor.* If it adheres to the floor, it may cause stains.

Do not use a suction cup towel bar, suction cupsoap dish, etc.* Doing so could cause discoloration.

Note

This product is designed for general home use. Ifput to other use such as business use, its life mayshorten considerably.

Do not dip the shower head in the bathtub, washbasin, etc.* There is a danger of back flow of drained

water into the pipe.

If there is a danger of a frozen bathtub which hasa water faucet or aqua-jet, make sure to removewater according to the User’s Manual for eachequipment.* Remove bathtub water when there is a danger

of freezing in winter.If the reheating fixture is used, follow theinstructions in the User’s Manual for thereheating fixture to prevent freezing. If theaqua-jet is used, be sure to drain the waterregardless of the reheating fixture or otherequipment.

* Not doing so could result in product failureor breakage.

In a bathtub equipped with an Aqua-jet, do notuse soap, body soap or other such products.* Doing so could cause a large volume of suds

to be generated, causing the productbreakage.

Do not place vinyl hoses or other plastic productson the Ideatone bathtub for a long period of time.* The bathtub could be damaged by polyvinyl,

rubber or similar substances.

Be sure to use the specific bathtub lid for theIdeatone bathtub.* Depending on the material of the lid, the

bathtub could be damaged, lose its heatretaining ability.

For the Ideatone bathtub, keep the shower headon the upper shower hook when the bath is notused.* If the shower hose touches the bathtub for a

long period of time, it could damage thebathtub surface.

(Note) Ideatone is a bathtub with a thicktransparent layer on the surface.

ソレオ_目次～P07_E 07.1.17 3:40 PM ページ7

8

Use

Method

Plugging In and Out the Drain

■ Drain Plug TypePlease check the type that you use.

Push one way drain plugRubber plug

Adjust the water temperature when adding to thebathtub.* Directly adding very hot water (80°C/175°F or

higher) or making the bathwater too hot coulddamage or reduce the life of the bathtuband metal drain parts.

Do not strongly pull the rubber plug’s chain, orforce the chain’s attachment to turn.* Doing so could cause bathwater to drain, or

damage the drain plug.Do not stand on top of the drain plug while it is inthe open state or press unduly on the drain plugopening button while a heavy load is bearing onthe plug.* Doing so could cause bathwater to drain, or

a clogged drainpipe.

After removing the drain plug or drain core (forcleaning, etc.), correctly reinsert it before using.* Not doing so could cause a blocked drain

pipe or bad odor.

Do not press unduly on the drain plug seal ormechanism if their water freezes in winter.* Doing so could cause product breakage.If the drain plug is frozen and does not open orclose even if you press it, please pour hot waterbelow 40°C (105°F) on the drain plug to melt theice.

When plugging in the drain, check that the plug isnot tilted.* If the drain plug is tilted, a gap could allow

bathwater to drain.

Drain plug

Seal

Mechanism

Please note

Use Method/Filling the Bathtub with Hot Water

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ8

9

Use

Method


■ If You Have a Rubber Plug

■ If You Have a Push One WayDrain Plug

Press the push button to open and close the drainplug.

When filling the bathtub with hotwater Set the push button in the raised state. This plugsin the drain.

When draining the water outSet the push button in the lowered state. Thisplugs out the drain.

Drain opening

Drain core

Push button

Fill water

Drain water

Do not hold the chain when pulling out the rubberplug. Pull the ring attached to the plug.* Pulling the chain could cause damage.

Please note

Rubber plug

Drain plug

Push button

Drain plug

Firmly press the rubber plug into the drain openingwith your hand.

* If the rubber plug is not plugging the drain andwater is draining out, refer to page 56 on rubberplug maintenance , and adjust the drain core soit is exactly in place.

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ9

10

Use

Method

About the Faucet


With a thermostatically controlled faucet, if the temperature setting on the water heater is low (about40°C/105°F), the hot water coming out of the faucet will be lower in temperature than the displaytemperature. In this case, change the set temperature of the water heater to 10°C above the highesttemperature that you use.Also, the water temperature varies with the seasons. If in winter you adjust the water heater temperaturesetting higher than in summer, the setting will be closer to the actual temperature, and it will be morepleasant to use.For details, please see the water heater and faucet User’s Manuals.* If INAX Maintenance is requested, they will perform the adjustment (chargeable, see page 99).

ONE POINT

Always be sure to check the watertemperature before using a faucet orshower.* High temperature water could come out

and cause burns.

The faucet or shower hose becomes hotwhen using hot water. Be careful not totouch the surface of metal parts directlywith bare skin.* There is a danger of burns.

Do not attempt to operate the handle andturn off the water suddenly.* Doing this causes a water hammer

(impact sound) effect.* It also causes water to leak from the

pipes and can damage householdgoods, etc.

Do not move the faucet up or down, orapply undue force.* Doing so could cause damage or

injury.

After use, be sure to return the scale onthe temperature adjustment handle tobelow “40”.* Not doing so could cause hot water to

shoot out next time, causing burns.

Caution

If freezing is expected, look at the User’sManual for the faucet, and remove thewater.* Freezing damage could cause water

leakage, result ing in damagedhousehold goods, etc.

Before using, check if the selector handleis on the faucet side or shower side.* There is a danger of being unexpectedly

covered with hot water and beingburned.

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ10

11

Use

Method


If the automatic bathtub filling water heater is attached, see the water heater User’sManual.

■ Faucet TypePlease check your faucet type.

Embedded 2-handle faucetProduct numbersBF-8743MR,L-PUBF-8743MNR,L-PU(GMS-1269)

2-handle deck faucets(Auze)

Product numbersBF-A093B-PUBF-A093B-U-PU

2-handle deck faucets(eModern)

Product numbersBF-E093B-PUBF-E093B-U-PU

2-handle deck faucets(Astesia)

Product numbersBF-7093C-PUBF-7093C-U-PU

2-handle deck faucets(Mitis)

Product numbersBF-M093C-PUBF-M093C-U-PU

Wall-mounted 2-handlefaucets

(Auze)Product numbersBF-A305-PUBF-A305N-PU


(Astesia)Product numbersBF-7405-PUBF-7405-U-PU


(Mitis)Product numbersBF-M405-PUBF-M405-U-PU

Use the Faucet (Bathtub Side)

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ11

12

Use

Method

ご使用方法/浴槽にお湯をためる

■ If You Have a 2-Handle Deck Faucet (Auze, Astesia, or Mitis)

■ If You Have an Embedded 2-Handle FaucetFor details, see the faucet User’s Manual (GMS-1269).

Always be sure to first turn the cold water side handle on, then turn the hot water side handle to adjust thetemperature.


Always be sure to check the water temperature before using water from a faucet. Also, always be sureto turn off the hot water side handle first when finished.* High temperature water could come out and cause burns.

Caution


Caution

Turns on and stops the flow of hotwater.The mark on the handle is red.

Hot water side handle

Turns on and stops the flow of hotwater.The mark on the handle is blue.

Cold water side handle

* The illustration is Astesia.





Turns on and stops the flow of coldwater.The mark on the handle is black.

Faucet

Insulating cap

Faucet

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ12

13

Use

Method


* The illustration is for Astesia.


Turns on and stops the flow ofhot water.The mark on the handle is blue.




Turns on and stops the flow of hotwater.The mark on the handle is blue.



■ If You Have a Wall-Mounted 2-Handle Faucet (Auze)



Caution

■ If You Have a Wall-Mounted 2-Handle Faucet (Astesia, Mitis)



Caution

Faucet

Faucet

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ13

14

Use

Method

ご使用方法/洗い場でお湯を使う

Use the Faucet (Washing Area Side)

■ Faucet TypePlease check your faucet type.

* If your bathroom has a dresser counter attached, we recommend using a bath stool which is about20cm high. Also, using a bath stool with rubber tipped legs protects the floor surface from scratches.

* Do not use a bath stool with metal legs made of hard material like metal. Doing so can mark the floorand scrape the surface.

* If you place the wash basin on the counter, it can fall on the floor, depending on how it is used andwhere it is placed.Using a wash basin with diameter below 27cm, with rubber attached to the bottom surface, preventssliding and scratches on the counter surface.

GTU and UDU typeEmbedded thermostaticallycontrolled faucetsProduct numbersBF-8743T-PUBF-8743TN-PU(GMS-1268)

Use Method/Using Hot Water in the Washing Area

Push faucetsProduct numbersBF-R741TR(L)-D-PU2BF-R741TNR(L)-D-PU2(GMS-1317)

Wall-mountedthermostaticallycontrolled faucets(Auze)Product numbersBF-A146T-PU4BF-A146TN-PU4(GMS-1299)

Wall-mountedthermostaticallycontrolled faucets(Moderno)Product numbersBF-X146T-MD-PUBF-X146TN-MD-PU(GMS-1346)

Wall-mountedthermostatically controlledfaucets(eModern)Product numbersBF-E146T-PUBF-E146TN-PU(GMS-1345)

Wall-mountedthermostatically controlledfaucets(Jeweller)Product numbersBF-J146T-PUBF-J146TN-PU(GMS-1344)

Wall-mountedthermostatically controlledfaucets(Astesia)Product numbersBF-7146T-PU1BF-7146TN-PU1(GMS-1077)

Wall-mountedthermostatically controlledfaucets(Astesia)Product numbersBF-7145T(250)-PU2BF-7145TN(250)-PU2(GMS-1077)

Wall-mountedthermostaticallycontrolled faucets(Mitis)Product numbersBF-M145T(250)-PU2BF-M145TN(250)-PU2(GMS-1078)

Wall-mounted 2-handlefaucets(Astesia)Product numbersBF-7115H(250)-PU1BF-7115HN(250)-PU1(GMS-1062)

Wall-mounted 2-handlefaucets(Mitis)Product numbersBF-M115H(250)-PU1BF-M115HN(250)-PU1(GMS-1062)

Wall-mounted 2-handlefaucetsProduct numbersBF-651(250)-PU4BF-651(250)-U-PU4(GMS-0083)

Wall-mountedthermostaticallycontrolled faucets(Mitis)Product numbersBF-M146T-PU1BF-M146TN-PU1(GMS-1078)

Wall-mounted 2-handlefaucets(Astesia)Product numbersBF-7115H(90)-PU1BF-7115HN(90)-PU1(GMS-1062)

Wall-mounted 2-handlefaucets(Mitis)Product numbersBF-M115H(100)-PU1BF-M115HN(100)-PU1(GMS-1062)

SSU counter type(Crank embedded faucet)Astesia, MitisModerno, Jeweller, eModernProduct numbersBF- 146T-PUBF- 146TN-PU(GMS-1347)

ソレオ_P08～P25_E 07.1.29 11:53 AM ページ14

15

Use

Method


■ GTU, UDU Type Embedded Thermostatically Controlled FaucetsFor details, see the User’s Manual for the faucet (GMS-1268).

When the handle is turned in the direction of the hot water side a little past “40”, the safety button functionstops the temperature adjustment handle to turn further. When it is necessary to obtain water hotter than40°C (105°F), hold down the safety button and turn the handle. For precaution, the temperature scale onthe hot water side stops near “45” (about 45°C/110°F).

ONE POINT

1 Turn the temperature adjustmenthandle until the water flowing out isabout 40°C (105°F).

2 When the water flowing out is about40°C, align the switch display buttonof the shower/bath selector handlewith the “止” mark on the base, so theflow of water stops.

3 Remove the handle cover and cap,then pull off the temperatureadjustment handle.* Remove the cap with a tool like a

small flat-head screwdriver.* Take care not to turn the

temperature adjustment handle.

4 Take the temperature adjustmenthandle which you pulled off, andinsert it so that its safety button alignswith “40” on the temperature display.

5 Replace the handle cover and cap.

● If the water temperature differs from that indicated on the temperatureadjustment handle, take the following steps to adjust the temperature.

Faucet

Temperature adjustment handle

Adjusts the temperature of the hotwater.

Shower/bath selector handle

To use the shower, turn thehandle to the left.To use the faucet, turn thehandle to the right.

Safety button

The handle stops when turned

a little past “40”.

Temperatureadjustment

handle

Temperatureadjustmenthandle

Handle cover

Cap

Do not to turn

Use a tool such as asmall flat-headscrewdriver.

Safety button

“40” display scale

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ15

16

Use

Method

■ If You Have a Push FaucetFor details, please see the User’s Manual for the faucet (GMS-1317).

How to start and stop hot water fromthe faucetPush the faucet ON/OFF button. The buttoncomes out ( ) and hot water flows from thefaucet.To stop, push the faucet ON/OFF button again.The button returns to its original position ( ).Water stops flowing.

How to start and stop hot water fromthe showerPush the shower ON/OFF button. The buttoncomes out ( ) and hot water flows from theshower.To stop, push the shower ON/OFF button again.The button returns to its original position ( ).Water stops flowing.

* Do not turn on the water from both the showerand faucet at the same time. There will be lesswater pressure.

How to adjust the water pressureFor more pressure, turn the water pressureadjustment jog dial clockwise. Turncounterclockwise for less pressure.

* You can not stop the water with the waterpressure adjustment jog dial.Operate the ON/OFF button to start or stop thewater.


Shower ON/OFF button

Faucet ON/OFF button

Water flowing setting( )

Water stopped setting ( )

Less water More water

Water pressureadjustment jog dial

ON/OFF button

Before using, check if it is on the faucet side or shower side, then operate the ON/OFF button.* If you make a mistake, there is a danger of being unexpectedly covered with hot water and

burned.

Do not put a heavy object such as a glass container on the counter.* If it slips and falls, there is a danger of injury.

Caution

Hotter

Cooler

Temperatureadjustment handle

Safety button

How to adjust temperatureThe temperature display number (temperaturescale) indicates the water temperature. Operatethe temperature adjustment handle as desired toadjust the water temperature.

When the handle is turned in the direction of the hotwater side a little past “40”, the safety buttonfunction stops the temperature adjustment handleto turn further. When it is necessary to obtain waterhotter than 40°C (105°F), hold down the safetybutton and turn the handle. For precaution, thetemperature scale on the hot water side stops near“H” (about 45°C/110°F).

ONE POINT

* The illustration is type R. The arrangement isopposite for type L.

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ16

17

Use

Method

How to lock the buttonUse this when cleaning, to prevent accidentaloperation.To lock the button, set the button to OFF (hotwater stops) ( ), and turn the water pressurejog dial to ( ).The button is locked. (the button’s ON/OFF islocked)* You cannot set the button lock while the button

is ON (water is flowing) ( ). First stop thewater, then set the lock.

* If water is flowing, do not push the ON/OFFbutton while turning the water pressureadjustment jog dial to the left. The button willlock, and the water cannot be stopped.

How to unlock the buttonReturn the water pressure adjustment jog dial tothe ( ) position.


To unlock

To lock

ON/OFF button

Water pressureadjustment jog dial



Handlecap

Flat-head screwdriver

Phillips-headscrewdriver(+)

Do not to turn

Do not use strength to pull the water pressure adjustment jog dial towards you.* There is a danger that the water pressure adjustment jog dial will come off, causing injury or

damage. If the water pressure adjustment job dial comes off, see the faucet 's User’s Manual, andattach it.

Caution

1 Turn the temperature adjustment handle untilthe water flowing out is about 40°C (105°F).

2 When the water flowing out is about 40°C,push the faucet ON/OFF button to stop thewater.

3 Remove the handle cap, loosen the screw, andpull off the temperature adjustment handle.* Remove the cap with a tool like a small flat-

head screwdriver.* Take care not to turn the temperature

adjustment handle.

4 Take the temperature adjustment handle whichyou pulled off, and insert it so that its safetybutton aligns with “40” on the temperaturedisplay cover.

5 Tighten the screw, and replace the handle cap.

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ17

18

Use

Method


■ If You Have an SSU Counter Type(Jeweller, eModern, Moderno, Astesia, Mitis)For details, see the faucet User’s Manual (GMS-1347).

When it is turned in the direction of the hot water side a little past “40”, the safety button function stopsthe temperature adjustment handle to turn further. When it is necessary to obtain water that is hotter, holddown the safety button and turn the handle. For precaution, the temperature scale on the hot water sidestops near “45” (about 45°C/110°F).

ONE POINT



2 When the water flowing out is about 40°C,adjust the switch display mark on theshower/bath selector handle to the “止 ”position, to stop the water.

3 Remove the cover and cap, and pull off thetemperature adjustment handle.* Take care not to turn the temperature

adjustment handle.

4 Take the temperature adjustment handle whichyou pulled off, and attach it so that itstemperature display mark aligns with “40” onthe temperature display.

5 Tighten the screw, and replace the handle cap.

Do not to turn

Temperaturedisplay mark

Cover


Faucet

Temperature adjustmenthandleAdjusts the temperature of the hotwater.


When using the shower, turn thehandle up.When using the faucet, turn thehandle down.

Safety button

The handle stops when it is alittle past “40”.

Temperaturedisplay button(red mark)

* The illustration is for Moderno.

Cap

For Moderno, Astesia, and Mitis faucetsWhen using the faucet, if you hang the shower hose on the hose clip, the shower hose will be out of yourway and easier to use.* Do not pull the shower hose strongly while the shower hose is hanging on the hose clip.* Note that you can not hang the shower head in the upper shower hook, nor raise the slide bar to the

higher position while the shower hose is hanging on the hose clip.

Shower hose clip(attached to Moderno,Astesia, and Mitis)

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ18

19

Use

Method


When using the shower,turn the handle up.When using the faucet, turnthe handle down.

Shower/bathselector handle

When the handle is turned in the direction of the hot water side a little past “40”, the safety button functionstops the temperature adjustment handle to turn further. When it is necessary to obtain water hotter than40°C (105°F), hold down the safety button and turn the handle. For precaution, the temperature scale onthe hot water side stops near “45” (about 45°C/110°F).

ONE POINT



2 When the water flowing out is about 40°C,align the switch display mark of theshower/bath selector handle with the “•” markon the base, so the flow of water stops.

3 Remove the cap, loosen the screw, and pull offthe temperature adjustment handle.* Take care not to turn the temperature

adjustment handle.

4 Take the temperature adjustment handle whichyou pulled off, and insert i t so that itstemperature display “40” aligns with thetemperature display mark.

5 Tighten the screw and replace the cap.

Cap

A screwdriver is required.

Temperature adjustmenthandle

Screw

Faucet

Faucet

Safety

button

Switch display mark Safety buttonSwitchdisplaymark

● Jeweler ● eModern

■ For Wall-Mounted Thermostatically Controlled FaucetsFor details, please see the User’s Manual for the faucet (Jeweler: GMS-1344, eModern:GMS-1345, Moderno: GMS-1346, Auze: GMS-1299).

Temperatureadjustment handleAdjusts the temperatureof the hot water.

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ19

20

Use

Method


■ For Wall-Mounted Thermostatically Controlled Faucets(Astesia, Mitis)For details, please see the User’s Manual for the faucet (Astesia: GMS-1077,Mitis: GMS-1078).

Temperature display button (red mark)

Safety button

Temperature displayDisplay button

Faucet

Shower

Align the desired temperature on thetemperature scale with the temperature displaybutton (red mark).


When using the shower,turn the handle up.When using the faucet,turn the handle down.


When the handle is turned in the direction of the hot water side a little past “40”, the safety button functionstops the temperature adjustment handle to turn further. When it is necessary to obtain water hotter than40°C (105°F), press down the safety button and turn the handle. For precaution, the temperature scale onthe hot water side stops near “45” (about 45°C/110°F).

ONE POINT



2 When the water flowing out is about 40°C,align the switch display mark of theshower/bath selector handle with the “止” markon the base, so the flow of water stops.

3 Remove the cap, and pull off the temperatureadjustment handle.* Once the cap is removed, you can pull off

the temperature adjustment handle with yourhand.

* Take care not to turn the temperatureadjustment handle.

4 Take the temperature adjustment handle whichyou pulled off, and insert i t so that itstemperature display “40” aligns with thetemperature display mark.

5 Replace the cap.


Cap

Take care notto turn

Temperaturedisplay mark

* The illustration is for Astesia.

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ20

21

Use

Method


* To turn off the water, first turn the hot water side handle to stop the flow of hot water, then turn the coldwater side handle and stop the flow of cold water.

* After use, turn the selector handle to the faucet side.

If the selector handle is turned so that it ispointing up, the effect is the same as ifthe handle has been turned to the Stopposition.

● In the case of faucets with thetemporary water cutoff function

Temporary water cutoff

FaucetShower


Turns on and stops the flow ofhot water.The mark on the handle is blue.


Turns on and stops the flow ofhot water.The mark on the handle is red.

Selector handle

Switches between the shower andthe faucet.When using the shower, turn thehandle to the left, and when using thefaucet, turn the handle to the right.

FaucetShower

* To turn off the water, first turn the hot water side handle to stop the flow of hot water, then turn the coldwater side handle and stop the flow of cold water.

Selector handle

Switches between the showerand the faucet.When using the shower, turn thehandle to the left, and when usingthe faucet, turn the handle to theright.


Turns on and stops the flowof hot water.The mark on the handle is blue.


Turns on and stops the flow ofhot water.The mark on the handle is red.

Faucet

Shower

When using the shower, temporarilyturn on the water from the faucetside, then turn the selector handleup to use the shower.When the water is stopped, theselector handle automatically returnsto the faucet side.

● If it has an auto returnfunction

Faucet

Shower

■ For Wall-Mounted 2-Handle Faucets [Dual Bathtub and WashingArea Faucets] (Astesia, Mitis)For details, please see the User’s Manual for the faucet (GMS-1062).

■ Wall-Mounted 2-Handle Faucets [Dual Bathtub and Washing AreaFaucets]For details, see the User’s Manual for the faucet (GMS-0083).

* The illustration isfor Astesia.

Faucet

Faucet

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ21

22

Use

Method


Use the Shower

■ Shower TypesPlease check your shower type.

Massage shower withswitchProduct numberBF-6GWBP(1.6)-PU

Massage shower(metallic tone)Product numberBF-6MBM(1.6)-PU2

Spray shower(metallic tone)Product numberBF-6LBM(1.6)-PU2

Switch shower

Product numberBF-8WBP(1.6)-PU

Spray shower

Product numberBF-6JBP

Spray shower

Product numberBF-6CBP(1.6)-PU

Only for eModernSpray shower (metallic tone)Product numberBF-6FMB(1.6)-PU

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ22

23

Use

Method

■ If You Have a Massage Shower with SwitchFor details, please see the User’s Manual for the shower.

Always be sure to check the water temperature before using water from a faucet or shower.* High temperature water could come out and cause burns.

Caution

Water sprays fromoutside the sprayplate.

Selector switchNormal

Water sprays frominside the sprayplate.

Selector switchMassage

Temporary cutoff the showerspray.

Temporary water cutoffswitch (Gray)

Restarts the shower spray.

Spray switch(Blue)

Using a selector switch in the front end of the shower head, the type of shower spray can be switchedbetween Normal and Massage.


Water can still trickle out from inside the shower head for a few seconds after stopping the water, butthis is water remaining in the shower head. This is not a defect in the faucet water shutoff. Whenreturning to the shower hook, first drain the remaining water completely out of the shower head, thenreturn it to the shower hook.

To change from a Spray shower to a Shower with switch, it must be replaced from the shower elbow orthe faucet base.

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ23

24

Use

Method


■ If You Have a Massage ShowerFor details, see the User’s Manual for the shower.

Always be sure to check the water temperature before using water from a faucet or shower.* High temperature water could come out and cause burns.

Caution

Turning the selector ring switches between Massageshower - Spray shower - Mist shower.

Massage ShowerThe shower sprays water intermittently. The same effectas having a massage is obtained.

Spray ShowerThis is a fine, vigorous shower spray. The appropriatemassage effect can be obtained.

Mist showerThis is a good-feeling fine mist shower spray which isgentle on the body and has a mild feel.

Water can still trickle out from inside the shower head for a few seconds after stopping the water, butthis is water remaining in the shower head. This is not a defect in the faucet water shutoff. Whenreturning to the shower hook, first drain the remaining water completely out of the shower head, thenreturn it to the shower hook.

Selector ring

ソレオ_P08～P25_E 07.1.18 10:13 AM ページ24

■ How to Use the Shower de BathFor details, see the User’s Manual for the Shower de Bath (GPU-0164).

1 Slowly turn the full body shower handle to theleft.Stop turning for a moment when you reach ( ), let cold water drain out of the pipethrough the faucet, and check the temperaturewith your hand.

* Cold water drains from the faucet, so run itin the wash basin to keep the water fromsplashing.

2 Adjust the arm’s angle to a position where thespray from the nozzle does not hit your face.

3 Slowly turn the full body shower handle to theleft.

4 Adjust the arm position and nozzle angle.

* The full body shower feels cooler than waterfrom a hand shower or faucet.

5 Align the full body shower handle’s projectionwith the “止” mark shown to stop the water.

* To drain water remaining in the Shower deBath, water comes out of the nozzle for awhile even after stopping.

6 After use, return the arm to the wall surface.

25

Use

Method

Use the Shower de Bath

Full bodyshower handle

Click

Chest

Thighs,

stomach

Knees

Ankles

Shoulder, back

50°

Always be sure to check the water temperature before use.* High temperature water could come out and cause burns.

Warning

To avoid placing undue force on the arm,please operate it slowly.* Fingers can be caught between the wall

and the arm, causing injury ordamage.

CautionDo not attempt to operate the handle andturn off the water suddenly.* Doing this causes a water hammer

(impact sound) effect.* It also causes water to leak from the

pipes and can damage householdgoods, etc.


ソレオ_P08～P25_E 07.1.18 10:13 AM ページ25

26

Use Method/Opening and Closing the Door

Use

Method

Locking and Unlocking a Door

■ Door TypeCheck your door type.

Type R swing door

Folding door

Tempered swing doorType U swing door

RDY- ( )

VDY- ( )

TDY- ( )UDY- ( )

SDY- ( ) SDY- ( )

One way sliding door 3-piece sliding door

Before using the bathroom unit, check if it is possible to unlock the door while the door is in the openstate. If by any chance the door cannot be unlocked, contact the retailer where you purchased thebathroom unit.

Except when the bath is in use, it is recommended that the bathroom door be closed and lockedfrom the outside to prevent small children from going into the bathroom by themselves.

Free select swing door

HDY- ( )

Do not splash water directly on the door ordoorframe.* Doing so could cause water to leak

outside the bathroom and get thehousehold goods, etc. wet.

CautionWhile taking a bath, or filling the hot wateror immediately after taking a bath, be sureto keep the door closed.* Opening the door causes the steam to

escape or water to leak outside thebathroom, getting the householdgoods wet.

* Even if the door is kept tightly closed, ifa vigorous shower is taken causing thewater to splash against the crackaround the door, some water may leakoutside the bathroom. The door’sconstruction is not such as tocompletely block out steam or light.

ソレオ_P26-49_E 07.1.29 11:58 AM ページ26

27

Use

Method


■ If You Have a Swing Door (Lever Handle) (Common for Type R,Type U, and Free Select)

● How to Use the Lock

From inside the bathroom

To lock the door, move the thumb turn lever to theright so that it is horizontally oriented.

To unlock the door, move the thumb turn lever sothat it is pointing down.

* If you leave the thumb turn lever horizontallyoriented when closing the door as you leavethe bathroom, the door will lock.

Unlock

Lock

From outside the bathroom

Fit a coin, etc. in the thumb turn slot and turn.To lock, turn unti l the thumb turn slot ishorizontally oriented.

Fit a coin, etc. in the thumb turn slot and turn.To unlock, turn unti l the thumb turn slot isvertically oriented.

ThumbTurn Lever

Thumb TurnSlot

Unlock

Lock

ソレオ_P26-49_E 07.1.18 10:19 AM ページ27

28


Use

Method

■ If You Have a Swing Door (Push Pull Handle, Free Select Door)

Unlock

Lock


Lock: Turn the lock knob inside the bathroom sothat it is horizontally oriented.

Unlock: Turn the lock knob inside the bathroom sothat it is vertically oriented.


“Pull” the handle to open the door.To close the door, push the handle.


“Push” the handle to open the door.To close the door, pull the handle.

Unlock

Outside the bathroom

Inside the bathroom

Lock

● How to use the push pull handle

Push

PullOpen

Lock knob inbathroom

Lock knoboutsidebathroom

● How to use the lock


Lock: Turn the lock knob outside the bathroom sothat it is horizontally oriented.

Unlock: Turn the lock knob outside the bathroomso that it is vertically oriented.

* If you leave the lock knob horizontally orientedwhen closing the door as you leave thebathroom, the door will lock.

If force is applied to push the handle outside the bathroom, the door will open. Locking the door whenclosed is recommended, to avoid the door opening by mistake.

ソレオ_P26-49_E 07.1.18 10:19 AM ページ28

29

Use

Method


開

閉

Unlock

Lock

■ If You Have a Tempered Swing Door* Some types have no lock mechanism.



To lock the door, push up the lock knob at the topof the door.

To unlock the door, lower the lock knob.




開

閉

Unlock

Lock

ソレオ_P26-49_E 07.1.18 10:19 AM ページ29

30

Use

Method


Unlock

Lock

■ If You Have a Folding Door








Unlock

Lock

ソレオ_P26-49_E 07.1.18 10:19 AM ページ30

31

Use

Method


■ If You Have a 3-Piece Sliding Door or One Way Sliding Door

Unlock

Unlock

Lock

Lock



To lock the door, turn the knob so that it ishorizontally oriented.

To unlock the door, turn the knob so that it isvertically oriented.


Fit a coin, etc. in the thumb turn slot and turn.To lock, turn until the thumb turn slot is horizontallyoriented.

Fit a coin, etc. in the thumb turn slot and turn.To unlock, turn until the thumb turn slot is verticallyoriented.

ソレオ_P26-49_E 07.1.18 10:19 AM ページ31

32


Use

Method

■ If You Have a Swing Door (Common For Type R and Type U)

Remove the door1 From outside the bathroom, lower the lock

knob in the top of the door frame.

2 Turn the lever handle and open the door a littleinto the bathroom.

Do not let go of the door until it is removed.

Reinstall the door1 While slightly tilting the door from outside the

bathroom (A), carry it inside the bathroom, andinsert the door’s lower pivot into the lower pivotreceptacle (B).

2 Following the above 2 and 3 in reverse order,attach the arm stopper in the top of the door.

3 Raise the lock knob on the top of the doorframe, and the door is secured.

* Check and clean if there is dirt sticking to thelower frame channel and door bottom. Afterreinstalling, check that the arm stopper iscorrectly attached.

* After installation, make sure the lock knob isreturned to its original position (up position).

3 Push up the arm stopper in the top of the door,pulling it out of the frame.

4 Tilt the top of the door into the bathroom (A),and lift the door upward (B).

While tilting the door slightly, pull it outside thebathroom (C).

Arm stopper

A

B

Knob

Lower

Handle

Lower pivotLower pivot receptacle

Slider

Remove the Door in an Emergency

A

C

B

Lower

Knob

Pushed up by a spring

ソレオ_P26-49_E 07.1.18 10:19 AM ページ32

33

Use

Method


■ If You Have a Free Select Swing Door

Remove the door1 From outside the bathroom, lower the lock

knob on the top of the door frame.

2 Turn the lever handle and open the door a littleinto the bathroom.

Do not let go of the door until it is removed.


bathroom (A), carry it inside the bathroom, andinsert the door’s lower pivot into the lower pivotreceptacle (B).While holding the lock knob down, insert thetop of the door.

2 Use the steps on the following page to attach the arm stopper in the top of the door.

3 Raise the lock knob on the top of the door frame, and the door is secured.

* Check and clean if there is dirt sticking to thelower frame channel and door bottom. Afterreinstalling, check that the arm stopper iscorrectly attached.

* After installation, make sure the lock knob isreturned to its original position (up position).




A

C

B

A

B

Stem

Knob

Lower

Handle

Lower pivotLower pivot receptacle

Knob

Lower

Arm stopper

ソレオ_P26-49_E 07.1.18 10:19 AM ページ33

34

Use Method/Open and close doors

Use

Method


There is an arm stopper attached in the top of thefree select swing door.If it comes off by chance, use the following outlineto attach it.

1 Move the slider on the top edge of the door tothe side where the door is hinged.

2 While the door is half open, insert the armstopper's plug into the door frame channel.

3 Fully open the door, and the arm stopper isheld by the slider.

● About the arm stopper on the free select swing door

Arm stopper

1

2

Slider

ソレオ_P26-49_E 07.1.18 10:19 AM ページ34

35


Use

Method

You can remove the door by using a tool such as a flat-head screwdriver to push up the metalemergency release lever on the top of the door. But this is extremely dangerous as the door is made oftempered glass.Never touch the emergency release lever except in an emergency.* The door could come off and fall over, resulting in broken glass and injury.

When removing the door in an emergency, always be sure to do it with 2 or more people.* The door is extremely heavy, so when it cannot be supported, it can fall over causing injury or a hurt

back.

When removing and attaching the door, it is not secured. Always be sure to have one person supportingthe door while working.

Caution

■ If You Have a Tempered Swing Door

Remove the door1 Open the door less than 1/3.

* The door cannot be removed if it is openmore than 1/3.

2 Raise the emergency release lever to releasethe door.





bathroom (A), carry it inside the bathroom, andinsert the door’s lower pivot into the lower pivotreceptacle (B). Insert the top of the door.

2 Attach the arm stopper.

3 Lower the emergency lever.

4 Check that the door is securely installed.

There is an arm stopper attached in the top of thetempered swing door.If it comes off by chance, use the following outlineto attach it.

1 Move the slider on the top edge of the door tothe side where the door is hinged.

2 While the door is half open, insert the armstopper's plug into the door frame channel.

3 Fully open the door, and the arm stopper isheld by the slider.

● About the arm stopper on the tempered swing doorArm stopper

Slider

1

2

A

B

A

C

B

Emergency release lever

Arm stopper

ソレオ_P26-49_E 07.1.18 10:19 AM ページ35

36

Use Method/Open and close doors

Use

Method


■ If You Have a Folding Door

Remove the door1 From inside the bathroom, lower the lock

knobs in two places, at the top left and top rightof the door.

2 Tilt the top of the door into the bathroom. Liftthe door upward. Remove the upper doorwheels from the upper door frame.

* The door could fall into the bathroom side,so keep firm control of the door.

Reinstall the door1 Align the direction of the door wheels as shown

in the illustration.

2 Lower the lock knobs in two places, at the topleft and top right of the door. Attach the door.

* Incorrect installation could cause waterleakage or the door to come off the framewhen opening or closing.

* Attach the door while open. It cannot beattached while folded.

* Even if the lock knobs cannot raise andlower the upper door wheels, do not removethe upper door wheels and lock knobs fromthe door. They cannot be returned to theiroriginal positions.

* When placing the removed door, be carefulnot to drop the door. There is a danger ofdamaging to the lower door wheels.

* When installing, check that there is not dirtstuck to the wheels below the door, thenattach.

Upper door wheels

Case

Lock knob

If handle on right

If handle on left

ソレオ_P26-49_E 07.1.18 10:19 AM ページ36

37


Use

Method

■ If You Have a 3-Piece Sliding Door or One Way Sliding Door

1 Use an item like a coin to open the lock on thefixed side of the door.

2 Lift up the door, and remove it while pulling thelower part towards you. For a 3 piece door, usethe same general procedure to remove theentire door.

Unlock

ソレオ_P26-49_E 07.1.18 10:19 AM ページ37

38

Use Method/Using the Fixtures

Use

Method

Slide bar890 -BTYPE-L / +R291/

Slide barBF-27B ( )-PU

Hook for roll-up coverR122

Hook for multi-piececover

FK- /

Handy mirrorR293/

Hand grip bar890 -BTYPE-L /

R2937-BTYPE-L

Ceiling ventilatorUF-23A (GPU-0047)UF-26A (GPU-0135)

Use the Fixtures

■ Fixture TypeCheck the fixtures you use.

Do not put fragile objects such as glasscontainers on high shelves.* There is a danger of causing injury by

dropping and breaking these objects.

CautionDo not apply undue force to the shelves orcounter.* Doing so could cause damage or injury.

Do not hang from or apply undue force tothe towel rod, shower hook, laundry pipe,ceiling light cover, s-shape hook, flatshelves, or other interior products.* Doing so could cause damage and

water leakage.* The flat shelves can come off, causing

injury.

Aqua-jetJP-4A2

Sound systemBAB-2BM

Laundry pipeLAP- -P

ソレオ_P26-49_E 07.1.29 11:58 AM ページ38

39


Use

Method

Ventilate

■ How to Use the Ventilator FanFor details, see the User’s Manual for theventilator fan.

Press the power switch on the outside wall of thebathroom to operate the ventilator fan.

* If you are running the ventilator fan, close thedoor and window.

Power switch

● To increase the durability of the bathroom and extend the service life of the ventilator fan, open thewindow or operate the ventilator fan after bathing to expel the moisture.

● If the constant (24-hour) ventilation system is used, set it high “強” after bathing to expel the moisturefrom the bathroom and then set it back to normal. Note that the constant ventilation system isnecessary for the entire home. Try keeping it on as much as possible.

ONE POINT

Store the Bathtub Lid

■ How to Use the Hook for Roll-up Lid

Do not quickly rotate the end of the bathtub lidhook, or exert undue force against it.* Doing so could damage it.

Please note When supportingWhen releasing

Hook for roll-up lid

Releasebutton

■ How to Use the Hook for Multi-Piece Lid

Slide the multi-piece cover to store it.

* The shape of your hook for multi-piece covermay differ.

Do not lean against the hook for multi-piececover, or apply undue force against it.* Doing so could cause damage or

injury.

Caution Hook for multi-piece lidMulti-piece

lid

While pressing the release button, rotate the endof the hook, releasing the hook for roll-up cover.

* To prevent accidents, turn the hook so that it isagainst the wall when it is not being used.

ソレオ_P26-49_E 07.1.18 10:19 AM ページ39

40


Use

Method

Use the Hand Grip Bar

Use the Slide Bar

It is used in the same way when getting in or outof the bathtub.

1 Hold on to the hand grip bar.

2 Step in (out) with the foot opposite from thehand that holds the bar. If you hold the handgrip bar with your left hand (as in theillustration), step in with your right foot first.* If there is a step in the bathtub, first step on

the step, then get in.

3 After both feet are set on the floor of thebathtub (washing area), and your body issteady, let go of the hand grip bar.

Up-down handle, right side

B

A

Up-down handle, left side

B

A

Adjust the spray direction1 Hang the shower head on the slide hook. Move

the shower head back and forth to adjust thespray direction.

2 Loosen the handle and rotate the slide hookdirection to adjust the spray direction.

Shower head

Slide hook

Do not turn the up-down handle too strongly in directions shown by the arrows A and B.* Doing so could damage the up-down handle.

Please note

To adjust the height1 Turn the up-down handle in the direction of

arrow A in the illustration.Align the slide hook to your desired position.

2 Turn the up-down handle in the direction ofarrow B in the illustration.This secures the slide hook in place.

1

2

Hand grip bar

Do not strike the slide hook against the mirror or wall.* Doing so could scratch the slide hook and wall, and crack the mirror causing injury.

Caution

ソレオ_P26-49_E 07.1.18 10:19 AM ページ40

41


Use

Method

Use the Handy Mirror

The mirror part of the handy mirror is not tempered glass.* Hitting the mirror could damage it, causing injury.

Caution

Raise and lower the handy mirror1 Turn the shaft to the right to loosen.

2 Raise or lower the handy mirror.

3 Turn the shaft to the left to tighten.

* Properly tighten so the handy mirror doesnot fall off.

Change angle of the handy mirrorPart of the slide bar rotates, and the angle of themirror part and slide bar changes.Adjust it to match your use.

■ How to Use the Handy Mirror

Loosen

Tighten Shaft

ソレオ_P26-49_E 07.1.18 10:19 AM ページ41

42


Use

Method

Use the Heater

■ Heater TypeCheck which fixture you use.

Electric 3-roomventilator/dehumidifier/heater

(100V)UFD-13A(GPU-0139)

Electricventilator/dehumidifier/heater

(100V, 200V)UFD-14A (GPU-0146)

UFD-15SA (GPU-0161)

Electric ventilator/dehumidifier/heater/ion type disinfector

(100V, 200V)UFD-14PA (GPU-0145)

UFD-15PSA (GPU-0162)

Do not hang items such as towels from the heateror ventilator fan intake hole.* Doing so could cause it to break.

Open the window or operate the ventilator fanafter bathing to expel the moisture.If the constant (24-hour) ventilation system isused, set it high after bathing to expel themoisture from the bathroom and then set it backto normal.* Moisture in the bathroom could cause bad

odors and mold to develop.

When using the ventilator fan, do not open thewindow or the door.* The bathroom will not be ventilated sufficiently.

Please note

ソレオ_P26-49_E 07.1.29 11:58 AM ページ42

43


Use

Method

■ How to Use the Ventilator/Dehumidifier/HeaterFor details, see the User’s Manual for the ventilator/dehumidifier/heater.* If a different company’s equipment is installed, read the User’s Manual attached with

the product and use it correctly.

Before taking a bath[Heater]In winter or whenever the bathroom is cold, the entire bathroom can be warmed by turning on the heater“暖房” or heater-before bath “暖房(入浴前)” about 30 to 60 minutes before getting in the bath.* The heater’s effectiveness will differ, depending on the bathroom size, season, and whether or not

there is a window.

While taking a bath[Ventilation]Stopping the ventilator is recommended.* If the ventilator is running while taking a bath,

water droplets may fall from the heater. Also,cold air from the door grille can make you feelcold.

[Heater]● Stopping the heater “暖房” or heater-before

bath “暖房(入浴前)” is recommended.* Hot air blowing directly against your body can

make you feel cold.

● Running heater-during bath “暖房(入浴中)” isrecommended.* Some heater types do not have the heater-

during bath “暖房(入浴中)” function.

After taking a bath● If water remains in the bathroom, lightly wipe up

using a towel.

● If there is hot water in the bathtub, drain thewater or put the lid on it.

● To make it difficult for mold to grow, running theventilator “換気” or dehumidifier “乾燥” afterbathing is recommended.

● In addition to the usual ventilator “換気” anddehumidifier “乾燥”, there are also units withfunctions of blow ventilator “ブロー換気”, cleanventi lator “クリーン換気 ”, and cleandehumidifier “クリーン乾燥”. If you have one ofthese, running the blow ventilator “ブロー換気”,clean venti lator “クリーン換気 ”, or cleandehumidifier “クリーン乾燥” is recommended.* The clean ventilator “クリーン換気”, and

clean dehumidif ier “クリーン乾燥 ” canprevent bathroom mold growth even more byemitting disinfecting ions.

ソレオ_P26-49_E 07.1.18 10:19 AM ページ43

44


Use

Method

About drying laundry● Thoroughly wipe off the bathroom moisture and

place the lid on the bathtub.

● Thoroughly remove the excess water from wetlaundry.

● Hang laundry which is harder to dry near thewarm air outlet.

● Leave spaces for the warm air to pass betweenthe laundry.

* Drying time depends on factors such asseason, room temperature, type of laundry,amount of water removed from laundry, andpositions for hanging laundry. Thus dryingtime is sometimes longer.

The constant ventilation system is necessary for the entire home. Try keep it on as much as possible.

ONE POINT

ソレオ_P26-49_E 07.1.18 10:19 AM ページ44

45


Use

Method

■ How to Use the 3-Room Ventilator/Dehumidifier/HeaterFor details, see the User’s Manual for the ventilator/humidifier/heater.* If a different company’s equipment is installed, read the User’s Manual attached with

the product and use it correctly.

Washroom

Bathroom

Air entry (grille) Toilet

Bathroom

WashroomAir entry

(grille) Bathroom

Expels bad air 24 hours from 3rooms (bathroom, washroom,toilet), to keep it pleasant inside.

Constant (24-hour) ventilationsystem illustration

Ventilation illustrationIllustration of heat, ventilation,

and cool air

Venti lates the bathroom andwashroom, suppressing moldgrowth and bad odors.

When the bathroom is cold, youcan warm up the bathroombefore bathing to make itpleasant.

Before taking a bath[Heater]In winter or whenever the bathroom is cold, the entirebathroom can be warmed by turning on the heater “暖房”about 30 to 60 minutes before taking a bath.* The heater’s effectiveness will differ, depending on the

bathroom size, season, and whether or not there is awindow.

[Ventilation]If the ventilator makes you feel cold, for example whilechanging clothes, you can stop it temporarily by pushingthe 24-hour ventilator “24時間換気” button on the remotecontroller.To return to constant (24-hour) ventilation operation,push the 24-hour ventilator “24時間換気” button on theremote controller again.

While taking a bath[Ventilation]If you turn on the bathroom light switch when theconstant (24-hour) ventilation system is running, thebathroom ventilation stops, and the washroom and toiletventilation increases.* Operating noise can increase when ventilation

increases in the washroom, etc.* The ventilator “換気”, dehumidifier “乾燥”, heater “暖房”, and cool breeze “涼風” can be used regardless ofthe bathroom lights.

[Heater]Turning off the heater “暖房” is recommended.* The warm breeze directly on your body can feel cold.

ソレオ_P26-49_E 07.1.29 11:58 AM ページ45

46


Use

Method

After taking a bath● If water remains in the bathroom, lightly wipe it

up using a towel.

● If there is hot water in the bathtub, please drainthe water or put the lid on it.

● To make it difficult for mold to grow, running theventilator “換気” or dehumidifier “乾燥” afterbathing is recommended.

● If constant (24-hour) ventilation is selected, thesystem automatically switches to constant (24-hour) ventilation operation after ventilator “換気”or dehumidifier “乾燥” stops.

About drying laundry● Thoroughly wipe off the bathroom moisture and

place the lid on the bathtub.

● Thoroughly remove the excess water fromlaundry.

● Hang laundry which is harder to dry near thewarm air outlet.

● Leave spaces for the warm air to pass betweenthe laundry.

* Drying time depends on factors like season,room temperature, type of laundry, amount ofwater removed from laundry, and positionsfor hanging laundry. Thus drying time issometimes longer.

The constant ventilation system is necessary for the entire home. Try keep it on as much as possible.

ONE POINT

ソレオ_P26-49_E 07.1.29 11:58 AM ページ46

47


Use

Method

Use the Laundry Pipe

■ Attach the Laundry Pipe

Securely insert the laundry pipe into the hooks onthe bathroom walls.

* You can remove the main hook part by sliding itup.

Main hook part

Do not attempt to hang from the laundry pipe or pull it down strongly.* There is a danger of injury.* 10 kilograms is a safe weight limit for laundry.

Caution

Hook

Laundry pipe

ソレオ_P26-49_E 07.1.18 10:19 AM ページ47

48


Use

Method

• Do not use with the safety cover removed or damaged.• Do not block the intake or outlet holes.• Do not go underwater in the bathtub.• Do not run the Aqua-jet while children are bathing by themselves.

* There is a danger of drowning or injury if hair or a part of the body get caught.

Warning

Use the Aqua-Jet

■ How to Use the Aqua-JetFor details, see the User's Manual for aqua-jet (GPU-0174).

Pressing the starts operation.Pressing it again stops operation.

Pressing the symbol switches the strength ofthe water jet.

* A built-in timer automatically turns off the aqua-jet after 15 minutes, in case someone forgets to turn itoff.

For replacement parts, refer to the Replacement Parts on page 101.

Remote controller

Jet outlet holes

ウエ

Jet nozzle

Intake hole Safety cover

ウエ

Hair catcher

Protectivemesh

Projection

Remote controller

The following people must not use the aqua-jet.People who are pregnant, physically weak,chronically ill, under the influence of alcoholor sleeping pills, have heart conditions orhigh blood pressure.* There is a danger of medical problems

arising.

CautionDo not use the aqua-jet for more than 15minutes.* There is a danger of straining the

heart.

ソレオ_P26-49_E 07.1.18 10:19 AM ページ48

49


Use

Method

Use the Sound System

■ How to Use the Sound SystemFor details, see the User’s Manual for the sound system (GPU-0175).

Electric lamp

This is lit green if normal.* If lit orange or flashing on and

off, output is too high, so lowerthe volume.

Power switch/volume

Turn right to turn on and adjustthe volume. To turn off, turn tothe left until you hear a click.

Your electronics

CD or MD player, radio cassette,etc.* If a radio comes near the

remote controller, there can benoise, so use as far away aspossible.

Input jack

Stereo mini jack for connectingexternal electronics

Stereo mini plug cord

Connects your electronics

Refrain from using at high volume to avoid bothering adjoining rooms and floors.

(If connected to the bathroom television)If the television is switched on while the sound system is in use, the television sound could start at an unexpectedlyloud volume.Please turn the sound system off, then switch the television on and slowly raise the volume.

Please note

● You can enjoy your favorite music while taking a bath.● To use, you only need to connect a desired music source, such as CD or MD player, radio cassette,

etc.

Speaker

Remote controller

ソレオ_P26-49_E 07.1.18 10:19 AM ページ49

Cleaning

Methods

50

Cleaning Methods/About Cleaning

■ To Always Keep the Bath Clean and Pleasant

Soak in the bath and “slimy!” Tiles and wall are also “slimy!”This ruins an enjoyable bath time. To spend a pleasant bath time in a clean and shiny bath, preventmold.

The person who last bathed cleans off that day’s dirt.To always keep the bathroom clean, it is important for the person used the bathroom last for the day toalways clean it.

First, lift and rinse off the dirt with a hot showerThe person who last uses the bathroom uses the shower to rinse dirt off the wall, bathtub, floor, mirror,faucet, etc. Use a soft sponge to scrub dirty buildup off the bathtub, etc.

Finally, eliminate bathroom warmth and moisture to suppress the growth of grime.Next, run a cold shower to lower the room temperature. Finally, it is effective to wipe places where waterremains with a dry cloth, and ventilate well. You can prevent almost all grime this way.

■ If Mold Grows

Mold can sometimes be just wiped off, but just this doesn’t completely kill it. It cannot be eliminatedwithout using fungicide.

Thus, we introduce a skillful way to eliminate mold.

* While cleaning, wear rubber gloves, mask, protective glasses (can be substituted with swimminggoggles), etc.

* Do not spray fungicide directly on places above head height.

1 Open the window or run the ventilator fan.

2 Spread fungicide on moldy areas.

3 Leave it and wait a while until the mold's color disappears.

4 Wash off thoroughly with cold shower water.

5 If grime is still a concern, use bathroom cream cleanser and a brush to scrub it off.

* When using fungicide or mold prevention chemical, be sure to carefully read the instructions anduse it correctly.

■ About Types of Grime, Cleaning Tools, and Reference

● There are various types of grime.There are many types of grime in bathrooms, and the cleaning method differs depending on the grime...... P51

● Special items are not needed for cleaning.If you just have these tools, you will not have difficulty with cleaning. ..... P52, 53

● Cleaning frequency differs depending on the place.Adjust to clean easily soiled places once weekly, and places that don't get very dirty once monthly. ..... P54

Tips for Cleaning

ソレオ_P50-64_E 07.1.18 10:29 AM ページ50

Cleaning

Methods

51


There are surprisingly many kinds of bathroom grime, and also variouscleaning methods.Specify the type of grime from its color or where it occurs. It is moreeffective to clean in a way appropriate for each type.

Type

Water stain

Calcium soap

Metallic (copper)soap

Mold

Rust

Rust stain

Slime

Pink slime

Color

White,Brown

White

Green,lightpurple

Black,purple,pink,etc.

Reddishbrown

—

Pink

Probable Place

Mirror,faucet (metal parts),bathtub ring,etc.

Floor,door,mirror,around bathtub,etc.

Mirror,inside bathtub,etc.

Entire bathroom

Floor,around bathtub,etc.

Around drain opening,etc.

Around drain opening,floor,etc.

Cause, Characteristics

Accumulation of silicic acid which is in thewater supply. Also results from elements likecalcium in the water supply combined withoxygen and carbon dioxide to form calciumcarbonate. Typically has a rough, whitishsurface.

Results from soap and body grease reactingwith metal ingredients like calcium in water.Typically hard, rough, whitish surface.

Result of tiny amounts of dissolved copperions from water heater parts and fromstandard and copper pipes, reacting withfatty acids in soap or body grease.

A type of microbe which grows in placeswhich combine temperature, moisture, andnutrient source (soap remains, water scale,body grease, etc.)

Compound resulting from metal surfacescombining with oxygen, also metal surfacesattacked by moisture or corrosive gases.

Result of rust adhering from wet hairpins,razors, spray cans, etc. Also from tiny ironparticles in water adhering.

Slime occurring in places where wateraccumulates, like in the drain opening.Results from germs clinging where there ismoisture, using grime as nutrient to grow.

Pink colored slime. This results from yeastgrowing on nutrients such as skin.

Cleaning Methods

Light scum can be easily removed bywashing with water. Scrub off scale buildupwith a synthetic bathroom cleaner (neutral).Apply liquid cleaner to the bathtub ring,leave 2 to 3 minutes, then it is easier toclean off.

Scrub off l ight grime using a syntheticbathroom cleaner (neutral). Scrub offstubborn grime with a bathroom creamcleanser, or toothbrush and toothpaste. (Donot use a toothbrush on the mirror.)

Copper ions easily dissolve from copperpipe surfaces in new construction, but thisusually lessens after a few months. Still,depending on water quality, it can continuefor many years. Scrub off grime buildup withbathroom cream cleanser, taking care not toscratch the surface.

To prevent grime remaining after taking abath, thoroughly wash off everywhereincluding all corners, and properly ventilate.If soon after mold appears, clean off withsynthetic bathroom cleaner (neutral). Ifdiff icult to remove, use commerciallyavailable fungicide to remove.* When using fungicide, read all the

warnings on the product.* For details, please read the section in

thisg manual “If Mold Grows”.

To prevent occurrence, remove metalsurface grime, and wipe off water droplets.Remove stubborn grime with a syntheticbathroom cleaner (neutral) or bathroomcream cleanser, then polish with a dry cloth.

Scrub off stubborn stains with a bathroomcream cleanser, taking care not to scratchgsurfaces.

Put synthetic bathroom cleaner (neutral) ona sponge for cleaning.

Put synthetic bathroom cleaner (neutral) ona sponge for cleaning.

About Grime

ソレオ_P50-64_E 07.1.18 10:29 AM ページ51

Cleaning

Methods

52


Items to Prepare

Prepare appropriate cleaning tools and cleansers to clean the bathroomeffectively.

Synthetic bathroom cleaner (neutral)

Bathroom cream cleanser

Fungicide

Bath heater cleanser

Mix of ingredients for bathroom use, strong against grime likewater stain, soap scum, etc. Leftover cleaner causesdiscoloration and stains, so rinse thoroughly after use. Forpeople with sensitive skin, kitchen detergents are alsorecommended.

Weak alkaline minute particle cleanser. Scrubbing too hardcan scratch the bathtub and make the bathtub too glossy, sobe careful. Also, do not use regularly.

Removes mold with alkaline cleaner. If you spray on andleave it for a longer time than indicated, or detergent remains,it can cause discoloration, rust, and rubber deterioration, sorinse off thoroughly after use.

Generates foaming bubbles to remove grime in pipes andinside the bath heater.

Cleaner * When using fungicide or mold prevention chemical, be sure to carefully read the instructions and use it correctly.

Sponge

(and a long-handled sponge for highplaces)

Soft cloth

Rubber gloves

Bathroom brush

Toothbrush

A soft sponge that is a litt le larger than your hand isrecommended. Wide areas can be cleaned with fewmovements.Be careful when using melamine foam, as scrubbing too hardcan leave scratches.* Melamine foam is a melamine resin sponge sold in a home

improvement retailer, etc. It is used without cleaner. Soak itin water and scrub off grime. It shrinks like an eraser as it isused by rubbing off.

Dust-cloth, old T-shirt or towel, etc.* Neat trick: By using a water wiper or absorbent car washing

towel, you can quickly remove bathroom moisture.

If used by bending them, hands won’t get wet with water orcleaner. If you wear cotton gloves inside rubber gloves, itprevents skin roughness.

For scrubbing wide areas such as the floor. Resin bristles arerecommended to avoid scratching the floor.* For cleaning a thermo-floor, use a split-end fine brush.

Use a worn out toothbrush with spread out bristles.

Cleaning Tools

ソレオ_P50-64_E 07.1.18 10:29 AM ページ52

Cleaning

Methods

53


Even if the bathtub is not filled with hot water,plug the bathtub drain if pouring large amounts ofwater into the washing area from a bucket, washbasin, etc.* There is a danger that the drained water will

flow back into the bathtub.

Use a cleaner suitable for the waterheater.

Please note

After fungicide is used, leaving it a long time cancause discoloration of surfaces.Also, metal faucet parts and the door frame canrust, and the drain plug’s rubber part candeteriorate. After use of fungicide, rinse it sothere is no remaining cleaner.

No matter what type of detergent or cleaner youuse, do not leave it for a long time after spreadingon the bathtub, floor, walls, or counter. Rinsethoroughly with water to avoid leaving cleaner. Ifcleaner remains, there is a danger that it willcause discoloration or deterioration of materials.

After cleaning, thoroughly rinse off the cleaner.* It can cause stains.

Carefully read the usage warnings on thecleaner label before using.

Hard spongeMetal or nylon scrub brush

Detergents or cleansers which display “acidic”or “alkaline”Strong abrasives such as fine powderedcleansers, polishing powdersSolvents such as thinner or acetone•Detergents or solvents which have chemicals suchas hydrochloric acid or those noted above.

Cause scratches and damage.

Cause surface discoloration and stains.

Cause scratches and damage.

Cause surface discoloration and stains.

Do not use

Recommended cleansers

Super cleaner banno Jr. kun(スーパークリーナー万能Jr.くん)

Cream cleanser jif bath cleaner(クリームクレンザージフ　バスクリーナー)

Neutral plant based cleanerAvailable in a home improvement retailer, etc.

Compound which includes a fine particle polishing cleanser.Available in a home improvement retailer, etc.

Always be sure to have sufficientventilation while using chemicals likefungicide.

Do not use chlorine cleaners, cleaners withacidic detergent, or mixed cleaners.(Using at the same time or using one afteranother can create harmful chlorine gas)

Warning

When using fungicide, make sure that itdoesn’t splash onto your eyes or clothes.* Wearing items such as a mask,

protective glasses, and rubber gloves isrecommended.

Do not use fine powdered, scouring powder,lacquer, thinner, alcohol or hydrochloric acid,ammonia, caustic soda, or similar chemicals orbleaches.* Using such substances could cause scratches,

discoloration or otherdamage.If using alkaline chemicalssuch as mold removalcleansers, or citruscleansers (limonene), besure to read the instructionscarefully and use themcorrectly. Also, quickly wash off with waterafter use.

Caution

When using a cleaner which is not a syntheticbathroom cleaner (neutral), check beforehand ona place out of view that it does not causeproblems like discoloration.

Do not use melamine foam (refer to page 52) onprinted faucet metal parts (temperature,shower/faucet switch display, etc.).* There is a danger of erasing the temperature

display or other printing.

ソレオ_P50-64_E 07.1.18 10:29 AM ページ53

Cleaning

Methods

54


Part

Bathtub

Reheater mouth(circulation mouth)

Bath cover

Bathtub drainopening

Wall

Floor

Ceiling

Floor draintrap

Under bathtub

Mirror

Hand gripbars, slide bar,towel rod

Shelves,counter

Faucet

Door

Lights

Ventilator fan,heater

Once/Week

Use a toothbrush to removefilter grime.

Use a toothbrush to removeremaining grime.

Remove dirt buildup andhair.

Rub clean with a sponge.

Clean caulking on edges offloor with synthetic bathroomcleaner (neutral).

Remove dirt and hair fromthe hair catcher.


Wipe off grime with a soft,dry cloth.

Wipe off softly with a spongesoaked in synthetic bathroomcleaner (neutral).


Daily

Clean by rubbing with asponge.

Briefly rinse off grime withshower after bathing.


Scrub with bathroom brush.


Wipe off grime with a dampcloth.

Once/Month

Clean pipes with a bathheater cleaner.

Scrub grime off joints withsynthetic bathroom cleaner(neutral).

Lightly scrub with a long-handled sponge.

Remove the water seal tubeand water passage pipe, andrinse off the grime.

Remove soap and waterscum with a syntheticbathroom cleaner (neutral).

Remove and wash the filtersand covers.

Once each 6 months, orwhen grime becomes visible

Scrub off metallic soap in thebathroom using a bathroomcream cleanser.

Put bathroom creamcleanser on a sponge, andscrub.

Remove mold with fungicide.

Remove mold with fungicide.

Remove and clean theapron.

Put bathroom creamcleanser on a sponge, andscrub.


Remove and wash the flatshelves with a syntheticbathroom cleaner (neutral).

Remove grime from thestrainer and shower f lowcontrol.

Use a toothbrush to removegrime from the door, underthe door, around the door,seals, etc.


Wipe off covers clean withsponge soaked in dilutedsynthetic bathroom cleaner(neutral).

Reference for Cleaning

Various cleanings are required because some parts become dirty eachtime of bathing, and some with everyday bathing.Careful cleanings are recommended depending on the grime and thefrequency in use.

Referencepage

55

55

56

56～57

58

59～60

61

61～62

63～64

65

66

66～68

69～79

80～82

83～90

91～95

ソレオ_P50-64_E 07.1.18 10:29 AM ページ54

Cleaning

Methods

55

Bathtub Cleaning

Rinse off bathtub grime with a hot shower. Use asoft sponge to scrub off grime buildup in thebathtub. Then use a cold shower to cool it off, andfinally wipe off the water.* When grime is hard to remove, put synthetic

bathroom cleaner (neutral) on a sponge, andscrub off.

Cleaning Methods/Cleaning around the Bathtub

Daily

When grime becomes visibleWhite grime buildup inside or on the edge of thebathtub is a stubborn deposit called “calciumsoap”.Put bathroom cream cleanser on a sponge, scruboff, then rinse off with water.* Do not scrub hard. Scrub 4 to 5 times, rinse

with water, then repeat until it is removed.

Please use in accordance with warnings and instructions written on a commercially available bathheater cleanser.* For details, please refer to the User's Manual for the equipment.

Caution

Cleaning the Reheater Port (Circulation Port)

* If you have installed a reheater port (circulation port) of a different company, be sure tocarefully read the instructions before cleaning.

Every week1 Turn the circulation mouth cover left towards

“はずす ” (remove). Align the △ of thecirculation mouth cover with the △ of thecirculation mouth. Then pull it off towards you.

2 Remove grime from the circulation mouthcover (filter) with a toothbrush, etc.

3 Align the △ of the circulation mouth cover withthe △ of the circulation mouth, insert it, andturn right towards “とめる” until it stops.

Every monthPlease use a commercially available bath heatercleanser.* Some bath heater cleansers are for 1 mouth,

others for 2 mouths.Please use a bath heater cleanser that is suitablefor the number of reheater port.

Filter

If scum and hair builds up in the filter, it can become clogged, so the bathwater heating function does notoperate properly.

Filter

Circulationport cover

Circulation port

Remove 1

Stop 2Remove 2

Stop 1

If INAX’s product

ソレオ_P50-64_E 07.1.18 10:29 AM ページ55

Cleaning

Methods

56

Bath Cover Cleaning


Also use a toothbrush or other tool to carefullyclean parts of the multi-piece cover which easilyget dirty, such as uneven spots or where thepieces are joined. After rinsing off with the shower,completely drying it in the shade is recommendedmore or less monthly.

Every week

When grime becomes visiblePut bathroom cream cleanser on a sponge andscrub off.

Cleaning the Bathtub Drain Opening

■ If You Have a Rubber Plug

Every week

1 Pull the drain core out by its knob, and removegrime.

* Do not wash this grime you removed downthe drain. It can clog the drain pipe.

Drain opening

Drain core

Rubber plug

2 Reattach the drain core in the drain opening.

* Make sure it is properly inserted into thefloor of the drain opening, not loose andtilted.If it is not properly inserted, the bathtubcannot be filled with water.

Drain core

Drain opening

Use the shower to rinse off sprayed water scumand soap scum. Then lightly polishing with a drycloth will keep it even beautiful.* If grime is difficult to remove, put synthetic

bathroom cleaner (neutral) on a sponge andscrub clean.

Daily

ソレオ_P50-64_E 07.1.18 10:29 AM ページ56

Cleaning

Methods

57


■ If You Have a Push One Way Drain Plug

Every week

1 Pull the drain plug straight up and out.

2 Remove the drain core from the drain opening,and remove grime attached to the drain core.

* Do not remove the stopper (white).


3 Hold the drain core knob to attach the draincore.

4 Attach the drain plug in the drain opening.Insert it until you hear a “clink” sound.

* If it is not properly inserted, the bathwatercan drain out.

5 Push the pushbutton to check if the drain plugopens and closes.

Drain plug

Drain core

Stopper

Click

● Cleaning the pushbutton

1 Attach something like adhesive tape to thepushbutton, push it down once, then lift toremove the button.

2 Remove slime and grime from the removedpushbutton.


3 While running the shower on it, push the centerrod to move it up and down. Continue until itmoves smoothly.

* Water that enters the pushbutton drains outunder the bathtub, so this is not a problem.

4 Reattach the pushbutton.* Insert it until you hear a “clink” sound.

When grime becomes visible

Click

Pushbutton

When plugging in the drain, check that the plug isnot tilted.* If the drain plug is tilted, a gap may allow the

water to drain from the bath.

Please note

● Cleaning the drain opening

ソレオ_P50-64_E 07.1.18 10:29 AM ページ57

Cleaning

Methods

58

Cleaning the Wall

Cleaning Methods/Cleaning the Wall, Floor, and Ceiling

1 Use the shower to rinse off sprayed shampoo,conditioner, and soap foam.* Lightly wiping with a dry cloth will keep it

clean even more.

2 Run the ventilator fan or open the window.

Daily

Place synthetic bathroom cleaner (neutral) on asponge and rub clean, then rinse off with water. Atthis time, lightly polishing with a dry cloth will keepit even more beautiful.

Every week

■ For Tile Grout

Place synthetic bathroom cleaner (neutral) on asponge and rub clean, then rinse off with water. Atthis time, lightly polishing with a dry cloth will keepit even more beautiful.

Every week

When there is mold on the grout, use acommercially available fungicide.

* If fungicide adheres to the floor, it could causediscoloration, so spread a sheet, etc. on thefloor to protect it.

* If fungicide or mold prevention chemical isused, be sure to carefully read the instructionsand use it correctly.

* Do not directly spray fungicide or otherchemicals on places above shoulder height.Fungicide can adhere to your face and clothes.


ソレオ_P50-64_E 07.1.18 10:29 AM ページ58

Cleaning

Methods

59

Protectivesurfacelayer

Insulationlayer

Foundationlayer

■ If You Have a Mosaic Pattern


Every month

When a mosaic pattern floor is dirty, its ability todrain worsens. Scrub vertically and horizontallyaligned with the mosaic pattern, using a bathroombrush with resin bristles and synthetic bathroomcleaner (neutral).

■ If You Have a Thermo-Floor

● Cleaning a thermo-floor

1 Rinse grime off the floor surface with a hotshower. Scrub off grime buildup with abathroom brush (with resin bristles). Then rinseoff with a cold shower, and lightly polish with adry cloth.

2 Run the ventilator fan or open the window.

Daily

Cleaning the Floor

When you first use it, there can be dust and other dirt adhering to the floor, so it is recommended that youclean it with a synthetic bathroom cleaner (neutral).The mosaic pattern of the floor surface is good for drainage, but water can remain in places and take long todry. Also, if grime like conditioner used while bathing adheres to the floor, it can become more difficult to dry. Itis recommended to diligently clean the floor with a synthetic bathroom cleaner (neutral).* Drying will take less time if you wipe remaining moisture off the floor with a cleaning sponge, brush, wiper,

etc.

Please note


Black grime can accumulate on the thermo-floor,for example near the washing area corners.Sometimes this grime cannot be removed withsynthetic bathroom cleaner (neutral) or fungicide.In this case, you can use a split end type finebrush (with resin bristles) to brush it out.

* A split end type brush can be purchased inhome improvement retailers.

Thermo-floor construction uses a unique 2mmthick insulation layer with minute air bubbles, ontop of a thermo-floor base (foundation layer).This insulation layer has the effect of reducingheat lost from the soles of feet touching the floor,compared to traditional floors. This can reduce the“cold” feet feeling when entering the bathroom.

● Thermo-floor construction

ソレオ_P50-64_E 07.1.18 10:29 AM ページ59

Cleaning

Methods

60


■ If There is Caulk Around the Floor Edges

Place synthetic bathroom cleaner (neutral) on asponge and rub clean, then rinse off with water. Atthis time, lightly polishing with a dry cloth will keepit clean even more.

Every week


* If fungicide adheres to the floor, it could causediscoloration, so spread a sheet, etc. on thefloor to protect it.


* If the caulking around the edges of the floorwears or comes off, there is danger of waterleakage. If caulking or grout wears or comesoff, please request repair from INAXMaintenance Co., Ltd. (refer to page 99).

* Do not directly spray fungicide or otherchemicals on places above shoulder height.Fungicide can adhere to your face and clothes.


■ If You Have a Tile Floor

Place synthetic bathroom cleaner (neutral) on asponge and rub clean, then rinse off with water. Atthis time, lightly polishing with a dry cloth will keepit clean even more.

Every week




The tile floor has a rough finish on the surface to make it less slippery. Water can remain on parts of it andtake time to dry. * When a lot of water remains on the floor, wiping it up reduces drying time.

If the tile floor cracks, chips, or scratches, please request repair from INAX Maintenance Co., Ltd.(Refoer to page 99)* Using it in such condition can result in injury.

Caution

ソレオ_P50-64_E 07.1.18 10:29 AM ページ60

Cleaning

Methods

61

Cleaning the Floor Drain Trap

1 Remove the floor drain cover, and turn the haircatcher to the left (counterclockwise).

2 Remove trash accumulated in the hair catcherand around the drain trap. Remove grime witha toothbrush, etc.

3 Remove slime and grime on and around thefloor drain cover.

4 After cleaning, turn right (clockwise) to attach,and set the floor drain cover in its originalposition.* Do not use if grime has accumulated in the

hair catcher or around the drain trap.This can cause slow drainage or a cloggeddrain pipe.

* Do not wash the removed grime down thedrain.Doing so can cause a clogged drain pipe.

Every week

Floor drain cover

Hair catcher

Drain trap


■ Clean the Hair Catcher and Around the Drain Trap

Flange

Never loosen the flange on the main part of the drain trap.* The drain trap can come off, causing water leakage.

Caution

Cleaning the Ceiling

Every month

1 When dust falls on moisture and hardens, moldgrows easily. Put synthetic bathroom cleaner(neutral) on a long-handled sponge, and scrublightly.

2 After removing grime, rinse with water to avoidleaving cleanser, then thoroughly wipe offmoisture with a dry cloth.

ソレオ_P50-64_E 07.1.18 10:29 AM ページ61

Cleaning

Methods

62


1 Turn the water seal tube to the left(counterclockwise) until it stops, then align thedrain trap tab with the indentation in the waterseal tube, and lift up.

2 Clean grime from the water seal tube and draintrap with a sponge, toothbrush, etc.* Do not remove the seal attached to the

water seal tube.

3 After cleaning, align the water seal tube withthe drain trap tab, insert, and turn right(clockwise) until it stops.

1 Remove the floor drain cover and hair catcher,then turn the water passage pipe 45°counterclockwise, and remove.

2 Clean off scum and grime in the water passagepipe with an old toothbrush, etc.

3 When attaching the water passage pipe aftercleaning, turn the ☆ mark on top of the waterpassage pipe, and the line on the side towardsthe bathtub. Insert it into the hole in the bottomof the drain opening, turn 45° clockwise, andattach.* Check that the △ mark and the “浴槽側”

(bathtub side) characters are towards thebathtub.

Every month

■ Cleaning Inside the Floor Drain Trap

● Cleaning inside the water seal tube and water passage pipe

● Cleaning the water passage pipe

Water seal tube

SealTab

Indentation

Do not use while the water passage pipe is removed.* Doing so can cause foul odors and pests.

Please note

Bathtub

OPEN

Water passage pipe

Water passagepipe

Line on side

Water passage pipe

Towards bathtub

ソレオ_P50-64_E 07.1.29 11:59 AM ページ62

1 Remove the apron side spacer

2 Remove the floor drain cover

* The illustration below is for a standardbathtub.

Cleaning

Methods

63


When cleaning under the bathtub, pleaseuse rubber gloves and clothing that doesnot expose your arms.* There is a danger of injury.

Do not directly put your hands or armsunder the bathtub.* There is a danger of injury on

protrusions

Caution

Cleaning Under the Bathtub

Apron

Counter

Apron side spacer (right)

Apron side spacer (left)

Floor drain cover

Partition plate

Every 6 months

Use the steps below to remove the apron side spacer.

1Grab it with your fingers, and pull towards you.

ONE POINT

2When the side towards the middle ofthe bathtub comes out, also grabthat side of the apron and pull out.

Apron side spacer (left)

Apron side

spacer (left)

Apron Apron

3 While pressing on the apron with one hand,pull the partition plate towards you to remove it.

ソレオ_P50-64_E 07.1.18 10:29 AM ページ63

Cleaning

Methods

64


Apron

Bathtub Counter

Hair catcher with grip

4 Push the upper part of the apron down, andremove from where it is inserted in the bathtub.

5 As shown in the illustration, pull the aprontowards you and rotate to pull it off.

6 There is a grip on the hair catcher for the drainopening under the bathtub. Pull out the haircatcher towards you, and remove grime fromthe hair catcher and drain opening.* Do not wash the removed grime down the

drain.It can cause a clogged drain pipe.

7 After cleaning, reattach the apron, partitionplate, floor drain cover, and apron side spacer(in that order).

Use the steps below to attach the apron side spacer.

1Insert the end in the corner.

ONE POINT

2Insert the side closer to the center ofthe bathtub.

* Left (左) and right (右) are marked on the 2 apron side spacers. Do not mistake left andright, and reattach with the correct side up.

ソレオ_P50-64_E 07.1.18 10:29 AM ページ64

65

Cleaning

Methods

Cleaning the Mirror

Cleaning Methods/Cleaning the Mirror

Use the shower to rinse off sprayed shampoo,conditioner, and soap foam. Lightly polishing witha dry cloth at this time will keep it clean evenmore.

Daily

Take synthetic bathroom cleaner (neutral), anddilute it to an appropriate strength. Soak a spongein this, lightly rub clean, then rinse off with theshower. At this time, lightly polishing with a drycloth will keep it clean even more.

Every week

Put bathroom cream cleanser on a sponge andscrub where there is water scum. After cleaning,wash thoroughly with water to leave no cleanser,and thoroughly wipe off water with a dry cloth.


Compounds which contain coarse abrasives such as abrasive particles will scratch the mirror, so becareful.

Hard items like a nylon scrub brush or the hard side of a sponge will scratch the mirror, so be careful.

Please note

About mirror life

When using the mirror for a long time, it is affected by water and oxygen which pass through the film.This causes dark stains on the edge of the mirror. (With high humidity, mirrors used in the bathroom canget this type of stains on other part as well). These dark stains cannot be removed, so it is a sign that it istime to replace the mirror.

ソレオ_P65-79_E 07.1.18 10:37 AM ページ65

Cleaning

Methods

66

Cleaning Hand Grip Bars, Slide Bar, and Towel Rod

お手入れ方法/アクセサリー類のお手入れ

Wipe off grime with a soft, dry cloth.

* Do not hit these items or bump against themwith hard objects. Doing so could scratch them or cause theplating to peel off.

* Do not bring alkaline cleansers or acidcompounds in contact with these parts. Theycould damage the plating.

Every week

Take synthetic bathroom cleaner (neutral), anddilute it to an appropriate strength. Soak a spongein this, lightly rub clean, then rinse off with theshower.


Cleaning the Flat Shelves and Counter

Liquid left under shampoo and conditioner bottlescauses mold and slime, so diligently wipe grime offthe storage shelf and counter surfaces.

Take synthetic bathroom cleaner (neutral), anddilute it to an appropriate strength. Soak a spongein this, lightly rub clean, then rinse off with theshower.

Every week

Remove the storage shelf and flat shelves doors.Take synthetic bathroom cleaner (neutral), anddilute it to an appropriate strength. Soak a spongein this, and clean off every inch of grime.

Rinse off with the shower, and reattach thestorage shelf and flat shelves doors.


Cleaning Methods/Cleaning the Accessories

Regardless of the type of detergent or cleanser, do not leave it for a long time after spreading it on the flatshelves, counter, etc.Thoroughly rinse with water to leave no cleanser.* If cleanser remains, there is a danger of discoloration and deterioration.

Please note

ソレオ_P65-79_E 07.1.18 10:37 AM ページ66

Cleaning

Methods

67


■ How To Remove Storage Shelf

● How to remove high-class storage shelves

1 Lift up storage shelves and remove.* To remove the metal part, grasp the center

of the metal part, rotate to release the 2ridges, and slide it off.

2 Reattach the storage shelf to their originalpositions, making sure they are level.* To reattach the metal part, slide the metal

part on to attach, and press until the 2 ridgessnap in.

Upper cover Lower cover

Storage shelf

● Remove the storage shelf

1 Lift and remove the storage shelf.

2 Reattach the storage shelf to their originalpositions, making sure they are level.

* Do the same for accessories storageshelves with hooks, square storage shelves,and storage shelves on a backboard.

* For high-class storage shelves, grasp thecenter of the metal part, rotate to release the2 ridges, and slide it off.After cleaning, slide the metal part on toattach, and press until the 2 ridges snap in.

Metal part

Metal part

ソレオ_P65-79_E 07.1.18 10:37 AM ページ67

Cleaning

Methods

68


● Remove arch shape storage shelves

1 Lift up to remove storage shelf.

2 Reattach the storage shelf to their originalpositions, making sure they are level.

● Remove corner storage shelves

1 Remove the guard bar.

2 Pull the shelf plate towards you to remove.

● Remove the acrylic make-up shelf

1 While supporting the acrylic shelf so it does notfall off, remove the screw under the bracket.

2 Insert the acrylic shelf into the bracket, andattach the screw under the bracket, whilesupporting the shelf so it does not fall off.

* After attaching, check that the shelf issteady.

Shelf plate

Bracket

Screw

Phillips-headscrewdriver (+)

Corner receptacle

Guard bar

Guard bar receptacle

Shelf plate

ソレオ_P65-79_E 07.1.18 10:37 AM ページ68

Cleaning

Methods

69

Cleaning the Faucet

Cleaning Methods/Cleaning the Faucet

Put synthetic bathroom cleaner (neutral) on asponge, wash off and rinse grime with the shower.Then lightly polishing with a dry cloth will keep itclean even more.

Every week

Use synthetic bathroom cleaner (neutral) ortoothpaste to scrub off the stained soap scum andwater stain.

Thoroughly rinse and polish with a dry cloth toleave no cleanser.

* If you have a push faucet, lock the buttonsbefore cleaning. For details, refer to page 17“How to lock the button”.

Every month

■ Cleaning the Shower Flow Control

Turn the cap by hand, remove the shower flowcontrol, and remove dirt or other debris from theflow adjustment meshes. Then wash with water.

* When reattaching, be careful that the flowadjustment meshes are not upside down.

* They can not be removed from some faucets.

Every 6 months

Flow adjustmentmeshes

Cap

Seal

If soap scum and water stain remain left on the faucet surface, they become difficult to get removed. Use theshower to rinse off sprayed foam, etc. If you also wipe off the moisture, it prevents water stain.

Cap

Flow adjustmentscreens

Showerflowcontrol

Showerflowcontrol

Do not use melamine foam (refer to page 52) on printed parts of faucet metal (temperature display,shower/faucet switch display, etc.).* The printed letters such as the temperature display may be erased.

Please note

If the metallic shower head got scratched, ask INAX Maintenance Co., Ltd. for the repair or exchange(refer to page 99).* Using it in such condition could result in injury.

Caution

ソレオ_P65-79_E 07.1.18 10:37 AM ページ69

Cleaning

Methods

70

■ Cleaning the Shower Spray Plate

For details, see the User’s Manual for the shower.


Turn the spray plate to remove by hand, rinse withwater in a container, and wash away dirt using atoothpick, etc.

* The spray plate cannot be removed from someshower heads.

Every year

* In the case of the shower with switch, do not remove the shower head or the shower hose.

Please note

Spray plateShower head

Shower hose

If dirt clogs the spray plate, water may not spray in the correct direction, or water may dribble out after

turning off the shower. In this case, remove dirt from the shower spray plate with a toothpick, etc.

ONE POINT

If it seems that water volume from the shower or faucet has decreased, clean the sprayplate and strainer.* If there is dirt in the spray plate, strainer, etc., it will cause a deterioration in water

flow. Clean the faucet occasionally with the following steps .

ソレオ_P65-79_E 07.1.18 10:37 AM ページ70

Cleaning

Methods

71

■ Cleaning the Strainer

For details, see the User’s Manual for the faucet.


●For GTU and UDU type embedded thermostatically controlledfaucets1 Turn off the water main valve of the house.

2 Remove the set screws from 3 places behindthe counter, and remove the under cover. (Ifthe faucet is the GTU type located on thebathtub side, also remove the bathtub sideunder cover in the same way).

3 Turn the handles of the flow adjustment valvesby hand to close them. (Turn the handles fullyin the clockwise direction.)

* Close the flow adjustment valve on both thehot water side (red) and cold water side(blue).

* Remember the original position of the flowadjustment valves.

When cleaning the strainer, be careful of the pipes, metal fittings, etc.* There is a danger of injury and burns.

Caution

When the water valve is opened and shut, dirt attached to the pipes can flow and clog the strainer again.

Before reattaching the cleaned strainer to the backflow prevention valve, first open and close the water

valve a little to allow dirt to flow out.

ONE POINT

Flow adjustment valve handle

Fixing screws

Under cover

Flow adjustment valve(Blue: cold water side)

Flow adjustment valve(Red: hot water side)

* The positions ofthe flow adjustmentvalves can differ,depending on thespecifications.

ソレオ_P65-79_E 07.1.18 10:37 AM ページ71

Cleaning

Methods

72


4 Remove the handle of the flow adjustmentvalve.

* The handles of the flow adjustment valvescannot be removed or installed again if thevalves are not completely closed.

* The pressure resistance of the f lowadjustment valves is 0.75 MPa.

5 Set the shower/bath selector handle fully openon the faucet side.

* Release the pressure inside the faucet andcheck that the flow adjustment valve hasstopped the flow of water.

* After checking, return the handle to the Stop“止” position.

6 Remove the strainer and wash away out anydirt or other debris that is caught in it.

* Press the + shaped projection on the handle(on the opposite side of the flow adjustmentvalve handle) against the + shaped grooveof the strainer, and turn left(counterclockwise) to loosen.

* A strainer is installed in both the hot waterand cold water sides. Clean the strainers forboth the hot and cold water lines.

7 Install the strainers by following the removalprocedure in reverse order, then reopen theflow adjustment valves to their originalpositions.

8 Install the under cover behind the counter.After inserting the cover in its receptacle,fasten it with fixing screws in 3 places.

Be careful not to let dirt fallinside the flow adjustmentvalve when removing thestrainer.

Strainer

Flip over the flow adjustmentvalve handle to use it as atool.

Fixing screws

Under cover

Flow adjustmentvalve handle


ソレオ_P65-79_E 07.1.18 10:37 AM ページ72

Cleaning

Methods

73


Flow adjustmentjog dial


● If you have a push faucet1 Turn off the water main valve of the house.

2 There are flow adjustment valves under thecounter.

3 Turn the handles of the flow adjustment valvesby hand to close them. (Turn the handles fullyin the clockwise direction.)

* Close the flow adjustment valve on both thehot water side (red) and cold water side(blue).

* Remember the original position of the flowadjustment valves.

4 Remove the handles of the flow adjustmentvalves.

* The handles of the flow adjustment valvescannot be removed or installed again if thevalves are not completely closed.

* The pressure resistance of the f lowadjustment valves is 0.75 MPa.

5 Press the faucet “ON/OFF” button to flow water( ), then turn the flow adjustment jog dialcompletely to the right.

* Release the water pressure inside the faucetand check that the flow adjustment valvehas stopped the flow of water.

6 Take out the strainer and wash away any dirtor other debris that is caught in it.

* Press the + shaped projection on the handle(on the opposite side of the flow adjustmentvalve handle) against the + shaped grooveof the strainer, and turn left(counterclockwise) to loosen.

* A strainer is installed in both the hot waterand cold water sides. Clean the strainers forboth the hot and cold water lines.


Flow adjustment valve handle

Flow adjustmentvalve handle

Counter

Flow adjustmentvalves

Be careful not to let dirt fall insidethe flow adjustment valve whenremoving the strainer.

Strainer

Flip the flow adjustment valvehandle over to use as a tool.

ソレオ_P65-79_E 07.1.18 10:37 AM ページ73

Cleaning

Methods

74


● If you have an SSU counter1 Remove the screws (2 places) from the cover

under the counter.

2 Slightly lower the front of the cover under thecounter, then remove the cover under thecounter by pulling towards you.

3 Use a tool like a flat-head screwdriver to screwthe hot (left) and cold (right) flow adjustmentvalves fully in the clockwise direction.

4 Turn the shower/bath selector handle to thefaucet side (down).

* Check that the water is stopped.

5 Remove the strainers with a large flat-headscrewdriver, and wash away dirt or other debrisfrom the strainers. A strainer is installed in boththe hot water and cold water sides.


7 Insert the back of the cover under the counter,returning it to its original position. Then attachthe screws (2 places).

Screws

Screws

Coverunder thecounter

Flow adjustmentvalve

Strainer

Cover underthe counter

Coverunder thecounter

ソレオ_P65-79_E 07.1.18 10:37 AM ページ74

Cleaning

Methods

75


● If you have a wall-mounted thermostatically controlled faucet

1 Use a tool such as a flat-head screwdriver toturn the hot (left) and cold (right) f lowadjustment valves ful ly in the clockwisedirection.

Flow adjustmentvalveFlat-head

screwdriver


Strainer

Flat-head screwdriver


* Check that the water is stopped.

3 Remove the strainers with a large flat-headscrewdriver, and wash away dirt or other debrisfrom the strainers. A strainer is installed in boththe hot water and cold water sides.


Less than 180 mm

For an arch shaped counter, use a short (lessthan 180 mm long) flat-head screwdriver, with alarge head.

For Mitis, Astesia, Moderno

For Auze, Jeweler, eModern

Strainer

ソレオ_P65-79_E 07.1.18 10:37 AM ページ75

Cleaning

Methods

76


■When the Faucet could Freeze in Winter

●How to stop water on a faucet with the shower with switchFor a faucet with the shower with switch, first open the water cutoff valve.For details, see the User’s Manual for the shower.

1 Secure the shower head at the upper end of the slide bar. (If you have a hook, hang the shower headin the highest hook). Press the blue shower switch of the shower with switch, turn the shower/bathselector handle to “シャワー( )” (shower), then drain water from the shower head.

2 Return the shower/bath selector handle to the stop position.

●How to stop water on a faucet with the shower with switch (incase of push faucet)For a faucet with the shower with switch, first open the water cutoff valve.For details, see the User’s Manual for the shower.

1 Press the blue shower switch of the shower head with switch, press the shower ON/OFF button to setit to the water flow state ( ), and drain water from the shower head.

2 Press the shower ON/OFF button to set it to the water stop state ( ).

● How to drain water from GTU and UDU type embeddedthermostatically controlled faucets1 Drain water using the drain valve in your

bathroom.

2 Open the 2 drain valves on the faucet.* The drain valves are on the left side of the

temperature adjustment handle.

3 Open the under cover, push the 2 check valveopening buttons to drain water from piping.

4 Turn the shower/bath selector handle to the “シャワー ” (shower) side, and open the drainvalve on the shower pipe.

5 Turn the shower/bath selector handle to the “吐水口 ” (faucet) side.

6 Turn the temperature adjustment handle fromthe “C” side to the “H” side several times.

7 Shake the shower head to thoroughly removewater, place the shower head carefully on thefloor so as not to scratch it, and drain thewater.

* To start water flowing again, close the3 drain valves, align the shower/bathselector handle in the “止 ” (stop)position, and return the temperatureadjustment handle to 40°C (105°F) orless.

Shower head

Shower pipe drain valve



Open watershutoff buttons

Drainvalve onthe faucet

ソレオ_P65-79_E 07.1.18 10:37 AM ページ76

Cleaning

Methods

77


●How to drain water from a push faucet

1 Drain water using the drain valve in yourbathroom.

2 Push the 2 check valve opening buttons underthe counter, then leave it for 1 minute or more.

Drain valve

6 When water stops flowing from the faucet, setthe shower flow adjustment jog dial to fullyopen. Press the shower ON/OFF button to setit to the water flow state ( ).



9 Shake the shower head to thoroughly removewater.

* Before starting water flow again, returnthe temperature adjustment handle to40°C (105°F) or less, then press thefaucet ON/OFF button and showerON/OFF button to set both buttons inthe water stop state ( ).

Counter

Check valve

3 Open the drain valve.

4 Set the faucet flow adjustment jog dial to fullyopen. Press the faucet ON/OFF button to set itto the water stop state ( ).


Check valve opening buttons



Shower ON/OFF button

Turn completely to the right

Faucet flowadjustment jog dial

Turn completely to the right

Shower flowadjustment jog dial

ソレオ_P65-79_E 07.1.18 10:37 AM ページ77

Cleaning

Methods

78


●How to drain water from an SSU counter faucet


2 Open the 2 drain valves on the attached legs.

3 Turn the temperature adjustment handlecompletely towards “C”.

4 Open the drain valve on the faucet.

5 Hang the shower head in the highest showerhook, and then the shower/bath selectorhandle to the shower side (up).





* Close the drain valves before flowing wateragain.



Drain valve onthe faucet

Drain valve onattached leg

Drain valve on attached leg

Spray switch

Shower head

ソレオ_P65-79_E 07.1.18 10:37 AM ページ78

Cleaning

Methods

79


●How to drain water from a wall-mounted thermostaticallycontrolled faucet1 Drain water using the drain valve in your

bathroom.

2 Open the 2 drain valves on the attached legs

3 Turn the temperature adjustment handlecompletely in the direction of “C”.

4 Open the drain valve on the faucet.

5 Hang the shower head on the highest showerhook, then turn the shower/bath selectorhandle to the shower side (up).






●How to drain water from a wall-mounted 2-handle faucet


2 Open the hot water side handle and cold waterside handle.

3 Open the 2 drain valves on the attached legs.




Drain valveon the faucet

Drain valve on attached leg

Drain valve onattached leg

Spray switch

Shower head

Hot water sidehandle

Drain valve Drain valve

Cold waterside handle

ソレオ_P65-79_E 07.1.18 10:37 AM ページ79

Cleaning

Methods

80

Cleaning Methods/ Cleaning the Door

Cleaning the Door

Wipe off splashed shampoo, conditioner, andsoap foam with a damp cloth.It is recommended to thoroughly wipe off moistureat this time, as mold grows easily on the door seal.

* When washing the door, do not directly spraywater on the door. Water can splash outside ofthe door.

* Diligently remove dirt accumulated in the doorframe. It can cause scratches.

Daily

When grime becomes visibleIf the grime is terrible in places such as on orunder the door, or on the door seal, clean offusing diluted synthetic bathroom cleaner (neutral)with a toothbrush or other tool.

Wipe off thoroughly with a damp cloth so thatcleaner does not remain.

* Dil igently clean the gri l le area (air entryopening) with a vacuum cleaner or the like, so italso does not clog.

* Do not use items which may scratch thesurface, such as brushes, abrasive chemicals,sponges which contain abrasive chemicals,dirty rags, etc.

The grille (air entry opening) is in the verticalframe on both sides of the tempered swing door.To prevent clogging, open up the vertical frameand diligently clean with a vacuum cleaner, wrungout wet rag, etc.

* Be careful not to jam a hand in the door whencleaning.

Grime on the bathroom side glass of thetempered swing door can be easily cleaned bywiping off with a rubber cleaning spatula, etc.

■ Cleaning a Tempered Swing Door and FIX Window

Tempered swing doors and FIX windows are madeof tempered glass. Shatter prevention fi lm isattached to the clothes changing room side oftempered glass for safety. When cleaning glasssurface on its clothes changing room side, lightlywipe with a rubber cleaning spatula or soft wet cloth.(Never polish with a dry cloth).

* Do not use items which can scratch the film,such as brushes, abrasive chemicals, spongeswhich contain abrasive chemicals, dirty rags, etc.

Please note

ソレオ_P80-106_E 07.1.18 10:45 AM ページ80

Cleaning

Methods

81


● How to remove the bottom cover of a one way sliding door and3 piece sliding door

How to remove the door1 Unlock the lock of the fixed door panel with a

flat-head screwdriver, etc.

2 While lifting up the door, pull the lower parttowards you.

This removes the door.* Starting with the panel on your side, remove

one panel at a time until all are removed.

How to remove the bottom frametrack1 Grab the lower frame track and lift it up to

remove it.

2 Remove dirt or other debris from the bottomframe track and door frame.

3 After the cleaning is completed, install the trackby performing the removal procedure inreverse order.

* Do not wash the removed dirt or other debrisfrom the drain. Doing so could clog thedrain.

■ Cleaning a One Way Sliding Door and 3-Piece Sliding Door

Unlock

ソレオ_P80-106_E 07.1.18 10:45 AM ページ81

Cleaning

Methods

82


The drain port under the doorThere is a hair catcher over the drain port underthe door. When cleaning the drain port, take outthe hair catcher and remove dirt. After cleaning,do not forget to replace the hair catcher.

* Securely fit the hair catcher’s tabs in the drainport.

* Only use synthetic bathroom cleaner (neutral)for cleaning the bottom frame area.Other cleaners can damage drain parts, orcause water leakage.

* Remove dirt and dust accumulated in thebottom frame grooves with a soft bristled wornout toothbrush, etc.

* Do not wash dirt from the drain port.Doing so can clog the drain pipe or cause waterleakage to outside the bathroom.

* Clean the bottom frame area about once aweek.

* Be careful not to drop the hair catcher in thedrain port by mistake.

Drain port

Hair catcher

ソレオ_P80-106_E 07.1.18 10:45 AM ページ82

Cleaning

Methods

83

Cleaning and Replacing Lights

Cleaning Methods/Cleaning and Replacing Lights

Dip a soft cloth or sponge in appropriately dilutedsynthetic bathroom cleaner (neutral), and wipe thegrime off softly .

Wipe off cleanser with a damp cloth.

* Do not hit or bump into the light with hardobjects. It may scratch the light.


■ Replacing light bulbs and fluorescent tubes in light fixtures

If the light does not come on even when the power switch is turned on, the fluorescent tube or the lightbulb may be burned out.Turn off the power switch, then replace the bulb or tube in the following procedure.If the light does not come on even after it has been replaced, contact the dealer where you purchasedthe bath system.

Always replace light bulbs and tubes withthe power switch turned off.* There is danger of electric shock or a

short circuit.

Besides replacing the bulb, do not attemptto disassemble or modify the light fixture.* Doing so could cause electric shock,

short circuit or breakdown.

Be sure to use fluorescent tubes or lightbulbs of the specified type and watts.* If this is not done, it could cause fire.

Replacing light bulbs or tubes is performedin a high place. Take adequateprecautions of the place you are standingon.Do not do this work by standing on the

bathtub.* There is danger of injury.

Do not replace a light bulb immediatelyafter it burns out.* The fixture and light bulb will be hot, and

there is danger of burns if it is handledtoo quickly.

Do not use a light with a removed ordamaged light cover.* There is danger of electric shock, or of

the bulb or tube breaking andcausing injury.

Securely attach parts l ike bulbs,fluorescent tubes, rubber seals, caps, etc.* Improper installation can cause electric

shock, injury, breakdown ormalfunction.

Be sure to use the light only with the lightcover fastened securely in place.* If it falls, it could cause injury.

Warning

Caution

ソレオ_P80-106_E 07.1.18 10:45 AM ページ83

Cleaning

Methods

84

Mini krypton light bulbGlobe

Stopper


● How to replace an incandescent bulb in the wall light fixture

For the cylindrical light, indirect light,square light, and half globe light

1 Turn off the light switch, then wait until thefixture and bulb are sufficiently cool.

2 Rotate the globe to the left and remove it.

3 Remove the light bulb, and replace with a newbulb (incandescent bulb).

4 Rotate the globe to the right, and securelyattach it.* For indirect lights and square lights, attach

so the upper surface is level.

5 Turn the light switch on and check if the lightcomes on.

For the thin shape light


2 Rotate the globe to the left and remove.

3 Remove the light bulb, and replace with a newbulb (mini krypton bulb).

4 Rotate the globe to the right, and securelyattach it.* For thin shape lights, come back a little from

where it hits the stopper, and attach so theglobe surface is vertical.


Appropriate light bulbsUse the light bulbs specified below in accordancewith the indications on the light fixture.* If a bulb other than the specified type is used, it

could cause a fire.

Appropriate Bulb

Silica light bulb 60W

RecommendedReplacement Bulb

LW100V54W

Incandescent bulb

Globe

For cylindrical lights, indirect lights, squarelights, and half globe lights

For thin shape lights

Appropriate Bulb

Mini krypton light bulb60W (E17 base)


100V 54W (white)

ソレオ_P80-106_E 07.1.18 10:45 AM ページ84

Cleaning

Methods

85


Globe

Globe

Base

Grooves(3 places)

Tabs(3 places)

Mini krypton light bulb

Rotate left about 20 degrees

Rotate right about 20 degrees

Seal

For the slice light


2 Firmly hold both sides of the globe, and rotateto the left about 20 degrees to remove theglobe.

3 Remove the light bulb, and replace with a newbulb (mini krypton bulb).

4 Align the globe’s tabs with grooves in the base,and while lightly pushing the globe into thebase, rotate to the right about 20 degrees toattach it.

* If the globe is wet, remove the moisturebefore attaching.

* Check that the seal is not twisted on thebase, then install the globe.

* Attach the globe so the globe upper surfaceof the slice light is level.Water cutoff performance is maintained,even if the globe angle is adjusted so that itsupper surface is level.


* Replace the globe if deformed or damaged.

Appropriate light bulbsUse the light bulb specified below in accordancewith the indications on the light fixture.* If a bulb other than the specified type is used, it

could cause a fire.

Appropriate Bulb

Mini krypton light bulb60W (E17 base)


100V 54W (white)

ソレオ_P80-106_E 07.1.18 10:45 AM ページ85

Cleaning

Methods

86


● How to replace an incandescent bulb in a down light


2 Lower the cover, and remove the spring whilepinching the 2 ends together.

3 Remove the light bulb, and replace with a newbulb (incandescent bulb).

4 While pinching the cover springs, insert it intothe spring insertion holes inside the fixture,then push the cover up and secure it so thereare no gaps.

5 Turn on the light switch and check if the lightcomes on.* The positions of the spring insertion holes

are at a 90 degree angle to the secure clip,so install correctly.(The arrow marks indicate the springinsertion holes).

Appropriate light bulbsUse the light bulbs specified below in accordancewith the indications on the light fixture.* If a bulb other than the specified type is used, it

could cause a fire.

Note that the knob for the secure clip is inside the fixture.Do not move the position of the secure clip.* There is a danger that the fixture can fall from the ceiling, causing injury.

Spring insertion hole

Caution

Cover

Springs

Arrowmark

Secure clip

Appropriate Bulb

Silica light bulb 60W


LW100V54W

ソレオ_P80-106_E 07.1.18 10:45 AM ページ86

Cleaning

Methods

87

1 Turn off the light switch, then wait until thefixture and tube are sufficiently cool.

2 Remove the resin head screws from under thelight cover, and slowly rotate the light coverwhile supporting it with both hands.

3 Pull out the light cover support towards you,and put the light cover on it.

4 Loosen the rings on the left and right of thefluorescent tube.

5 Slide the retaining rings and seals inside therings, and remove the fluorescent tube.

6 Place the retaining rings and seals on the newfluorescent tube, align the fluorescent tube’sterminals with the holes in the socket, andattach it.

7 Slide the seals until they hit the sockets, thenpush the retaining rings against them andtighten the rings.


● How to replace a fluorescent tube

Fluorescent tube Ring

Loosen

Resin head screws

Light fixture base

Cover

Cover support

Rotate the cover up,pivoting on the upperedge

Loosen

SealRingRetaining ringFluorescent tube

Tighten

SealRing

ソレオ_P80-106_E 07.1.18 10:45 AM ページ87

Cleaning

Methods

88

8 While supporting the light cover, return the lightcover support back inside, and slowly rotatethe light cover while pressing it’s back againstthe wall.

9 Screw the resin head screws into the lowerpart of the light cover.

Appropriate lampsUse the lamp specified below in accordance withthe indications on the light fixture.* If a lamp other than the specified type is used, it

could cause a fire.


How to remove the dropprevention wireRemove the wire ring fromthe fixture hook.* Do not remove the wire

from the fixture, exceptwhen removing the lightcover.

* Set the wire back to theorignal posit ion whenplacing the cover.

Drop prevention wire

Cover support* Be careful not to hit it when

closing the cover.

Take care not to jam thedrop prevention wire

Appropriate lamp

Fluorescent Quintron24W

RecommendedReplacement lamp

FHF24SEN

ソレオ_P80-106_E 07.1.18 10:45 AM ページ88

Cleaning

Methods

89


●How to replace a fluorescent tube in the embedded ceiling light

1 Turn off the light switch, then wait until thefixture and tube are sufficiently cool.

2 Pull down the entire cover.

2 Remove the springs from which the coverhangs. There are 2 or 3 springs on the front. Ifthere are 3 springs, remove the right and leftsprings first.

4 Pinch the two ends of the spring together andpull down, pulling it out of the spring holder.

5 Remove all the springs on the front, thenslowly lower the light cover while supporting it.Leave the cover as hung by the back springs.

6 Loosen the caps on both ends of thefluorescent tube, and slide the seals inside thecap.

Leave the springs on the back as hooked.

Socket

Fluorescenttube

Seal Cap

SlideLoosen

Socket

Cover FrameHold the frame to pull it down.

Remove the spring at both ends first.

Spring holder

Spring

Pinch together

Pull down

Pinch together

1 2 1

ソレオ_P80-106_E 07.1.18 10:45 AM ページ89

Cleaning

Methods

90


Remove Remove

Cap

Insert to fitthe terminalpart.

Washer

Seal

7 Remove the fluorescent tube from the socketsone end at a time.

8 Remove the caps, washers, and seals, placethem on a new tube, then install in the socketsby following the removal procedure in reverseorder. Securely insert the fluorescent tube inthe socket terminals.

9 Slide the seals on both ends toward thesockets, then tighten the caps.

0 Fasten the springs while holding the light coverup. If there are 3 springs , hook the centerspring first. Pinch both ends of the springstogether and hook them in the spring holders,following the removal procedure in reverseorder.

Appropriate Lamp

In the case of 40-watttubes

In the case of 20-watttubes

FLR40S/M

FLR20S/M

Straight tube with rapid start type, diameter :φ 32.5 mmRecommended light color: White, Incandescentlight colorStraight tube with rapid start type, diameter : φ 32.5 mmRecommended light color: White, Incandescentlight color

Recommended Replacement Lamp

Appropriate lampsUse the lamps specified below in accordance with the indications on the light fixture.* If a lamp other than the specified type is used, it could cause a fire.

* Fluorescent tubes which use a starter (Part No.: FL40SS/, FL20SS/) cannot be used.

Tighten the caps

Hook the center spring first.

Push up the entire light cover so that it is snug against the ceiling.

ソレオ_P80-106_E 07.1.18 10:45 AM ページ90

Cleaning

Methods

91

Cleaning the Ventilator Fan and Heater

* The shape can differ depending on the product. Explanation below is the general cleaning method. Fordetails, see the User’s Manual attached with each product.

* For ventilator fans other than INAX products, check the User’s Manual for each equipment.

Cleaning Methods/Cleaning the Ventilator Fan and Heater

Persons other than repair techniciansshould not attempt to disassemble, repairor modify this equipment in any wayexcept to remove the louver.* There is a danger of fire, mechanical

abnormality or injuries.

WarningBe sure to turn the power off beforecleaning the ventilator fan or heater.* There is a danger of electric shock or

injuries.

Do not splash wateron the ventilator fanor heater.* There is a

danger ofproductbreakage orcurrent leakage.

This operation isperformed in a highplace.Watch your step. Dustmay fall on your head.Do not stand on thebathtub or counter.

* There is a danger offalling and injuries.

CautionInstall the louverand air f i l tercompletely.* There is a

danger ofinjuries by thelouver or airfilter falling off.

Do not touch theheater right awayafter stoppingoperation.* There is a danger

of burns.

Wear rubbergloves whencleaning thelouver.* There is a

danger ofinjuries.

Do not use powdered cleansers, scouring powder, lacquer, thinner, alcohol, hydrochloric acid, or similarchemicals.* Using such substances could cause scratches, discoloration or other damage.

Also do not use sandpaper or a scrub brush, since they could ruin glossy finish and scratch the surface.

(Powder)

Please note

ソレオ_P80-106_E 07.1.18 10:45 AM ページ91

Cleaning

Methods

92

1 Stop operation, and remove the front cover.

2 Wipe off dirt with a dry soft cloth or a clothwrung out with hot water .

3 Return the front cover to the original position.

* Install the front cover securely. If improperlyinstalled, it could fall.

Every month

Dip a soft cloth or sponge in appropriately dilutedsynthetic bathroom cleaner (neutral), and wipe thegrime off softly .

Wipe off the cleanser with a damp cloth.

Return the front cover to the original position.* Install the front cover securely. If improperly

installed, it could fall.



Do not directly splash water on the unit, switches, or ceiling.* Doing so could cause breakdown and mold.

Do not apply an undue force on internal machine parts such as the fan.* Doing so could cause breakdown.

■For a Ventilator FanIf a different company’s equipment is installed, read the User’s Manual attachedwith the product and follow the given cleaning instruction.

Front cover

Main unit

Spring

Please note

ソレオ_P80-106_E 07.1.18 10:45 AM ページ92

Cleaning

Methods

93


■For a Ventilator/Dehumidifier/HeaterIf a different company’s equipment is installed, read the instruction manual attachedwith the product and follow the given cleaning instruction.

Accumulated dirt and dust in the fi l ter maydeteriorate the equipment performance.

* If you have the 3-room ventilator/dehumidifier/heater, clean the fi lters for the toilet andwashroom sub intake grille.

Every month

Clean the ventilator/dehumidifier/heater unit1 Stop operation, and wait until the area around

the intake and output vents get coolsufficiently.

2 Pull the filter grip to remove the filter.

3 Vacuum dust on the filter with a vacuumcleaner.

4 Replace the filter in its original position.

●Filter (some types do not have a filter.)

Filter

Filter

Front panel (cannot be removed)


Please note

* If you have the 3-room ventilator/dehumidifier/heater

ソレオ_P80-106_E 07.1.29 0:01 PM ページ93

Cleaning

Methods

94


Cleaning a sub intake grille (for the 3-room ventilator/dehumidifier/heater)1 Slowly remove the sub intake grille front with

both hands.

2 Remove the filter inside the sub intake grillefront.

3 Vacuum dust on the filter with a vacuumcleaner.

4 Set the filter in the sub intake grille front, andattach the sub intake grille front.

* Set the filter in the sub intake grille front.Install in a direction so that the concave partof the sub intake grille joint aligns with theconvex part of the sub intake grille front.

Sub intake grille joint

Sub intake grille front

Filter

Sub intake grille front

Concave part of thesub intake grille joint

Convex part of thesub intake grille front

ソレオ_P80-106_E 07.1.29 0:01 PM ページ94

Cleaning

Methods

95


1 Stop operation, and wait until the area aroundthe air exhausting port get cool sufficiently.

2 Wipe off dirt with a dry soft cloth or a clothwrung out with hot water.

Every month

1 Stop operation, and wait until the area aroundthe air exhausting port get cool sufficiently.

2 Dip a soft cloth or sponge in appropriatelydiluted synthetic bathroom cleaner (neutral),and wipe the grime off softly.

3 Wipe off cleanser with a wet cloth.



Please note

● Main unit, remote controller

ソレオ_P80-106_E 07.1.18 10:45 AM ページ95

Cleaning

Methods

96

Cleaning Methods/Removing the Ceiling Inspection Door for Maintenance

Removing the Ceiling Inspection Door for Maintenance

Open the ceil ing door to perform theinspection or repair when trouble occurson the electric cable, pipe or the like.Only the qualified person for the inspectionor repair can open the ceiling inspectiondoor. Do not place objects above theceiling.* Failing to observe the above instruction

could cause fire, electric shock orceiling damage.

Caution

Notify a construction worker of the instructions below when performing inspection or repair related to electriccables, water pipes, etc.

1 Turn the secure clip to the ceiling inspectiondoor panel side.

2 Push up the ceiling inspection door panel.

3 When reattaching the ceiling inspection doorpanel, return it to the ceiling inspection door,and turn the secure clips to the ceiling side.

Secure clip

Ceiling inspectiondoor panel

Be sure to lock the ceiling inspection doorsecure clip.* If failed, the ceiling inspection door

cover could fall, resulting in injuries.

ソレオ_P80-106_E 07.1.18 10:45 AM ページ96

Troubleshooting

97

Before Requesting Repairs

If the product breaks down, refer to the “Troubleshooting” section (page 98).If the trouble is still not corrected, contact the retail shop where you purchased the product or contact INAXMaintenance Co., Ltd.Furthermore, also contact us in the following cases, even if it is not the product trouble.● If there are any points that are unclear, even if the product is used in accordance with the instructions in

the User’s Manual.● If there are strange odors or sounds in or near the bathroom, turn off the fixture switches and electrical

distribution panel breakers, and quickly request repairs.Leaving the above situation as it is can lead to unexpected accidents. Be sure to contact us.

Troubleshooting

Persons other than authorized repair technicians should never be permitted to disassemble, repair ormodify this product.* Doing so could cause a fire, faulty operation or injury.* Continued use despite malfunction can cause fire, short circuit, and water leakage.

Warning

ソレオ_P80-106_E 07.1.18 10:45 AM ページ97

Part

Floor

Floor drain port

Reheater port

Ceiling

Door

Bathtub

Push one waydrain plug

Faucet

Shower

Storage

Lights

Ventilator fan, Ventilator/ dehumidifier/ heater

Water heater or itsremote controller

Problem

Water flows avoidingan area on themosaic pattern floor.

It takes time that waterdrain out from thewashing area floor.

Bad odors comefrom the drainopening.

The water heatingfunction is notworking right.

The ceiling inspectionwindow is rattling.

The door will not open.

Water leaks into theclothes changingroom from the bottomof the door frame.

Bathtub won’t fill up.(bathwater hasdecreased by thenext morning )

Takes a long timeto drain.

Water has been cooledwhen the next persongets in the bathtub.

The button doesnot move smoothly.

Water flow isweak.

Hot watertemperaturedoesn’t rise, or isunstable.

Water dribbles out fromthe shower head forseveral seconds afterwater is turned off.

Storage shelf rattles.

Lights do not turnon.

Cause

There is dirt in the mosaicpattern.

The drain trap or the hair catcheris clogged.

The water seal tube is not fit.

There is dirt accumulated in thedrain port.

The reheater port filter is cloggedwith hair, etc.

How to Check & Respond

Clean the floor along the directionof the mosaic pattern.

Clean the drain trap or the haircatcher.

Install the water seal tube correctly.

Remove dirt from the drain port,and clean grime if any.

Clean the filter.

The ceiling inspection window isnot secured.

The door is locked.

Hair or dirt accumulated in thedrain port under the door, sowater does not flow into the drainport.

Drain is not plugged or drain coreis not set correctly.

There is hair or dirt accumulatedin the drain port or drain core.

The bath lid is not being used, sohot water gets cool easily.

The pushbutton is grimy, or dirthas accumulated.

The strainer is clogged.

The hot water supplyperformance is deteriorated.

The temperature set on the waterheater is low.

The amount of water flowing fromthe faucet is low, so the waterheater cannot be ignited.

The hot water supplyperformance is deteriorated.

The strainer is clogged.

The temperature adjustment onthe thermostatically controlledfaucet is deviating.

Hot water is being used in thekitchen, washroom, etc.

This is water remained in theshower head. It is not a faucetwater shutoff malfunction.

Storage shelf are not properly secured.

The tube or bulb is not properlyinserted in its socket.

The tube or bulb is dead.

Secure the ceiling inspectionwindow.

Unlock the door.

Clean out dirt in the drain portunder the door.

Correctly plug the drain and setdrain core.

Clean out dirt from the drain portand drain core.

Use the bath lid.

Clean the pushbutton.

Clean the strainer.

Use hot water as little as possible atthe same time outside the bathroom.

Raise the temperature setting on thewater heater adding 10˚C or higherthan the highest temperature used.

Increase the water flow rate fromthe faucet.

Use hot water as little as possible atthe same time outside the bathroom.

Clean the strainer.

Reset the temperature adjustmenthandle setting (see the User’sManual for the faucet).

Reduce the hot water volume inother places.

When returning the shower headto the shower hook, first let thewater thoroughly run out of theshower head.

Properly secure storage shelf

Properly insert the tube or bulb inits socket.

Replace the tube or bulb.

Troubleshooting

98

Troubleshooting

Troubleshooting

Refer to Page

59

61

62

61

55

96

26～31

82

56、57

56、57

6

57

71～75

－

－

－

－

71～75

15～20

－

22～24

67、68

84～90

84～90

－

－

Iftheaction

onthe

leftdoesnotw

ork,pleaserequestus

torepair.

See the User’s Manual of each unit.

See its User's Manual, or contact the water heater manufacturer.

ソレオ_P80-106_E 07.1.18 10:45 AM ページ98

Troubleshooting

99

Troubleshooting

When Requesting Repairs

When you request repairs, read through this manual again. If you still have the problem after performingindicated methods, ask the dealer where you purchased the product or INAX Maintenance Co., Ltd. to carryout repairs.

Repairs during the Warranty Period

During the warranty period, repairs will beperformed in accordance with the provisions in thewarranty.

Repairs after the Warranty Period has passed

If the product’s function can be maintained byrepairing, we perform repairs with charge by thecustomer’s request.

Repair charges will include technical fees, travelexpenses and parts costs.

Required information when requesting repairs

1. Your name, address and telephone number

2. The product name, product No.←Refer to “How to Read Part Numbers” inside the cover page

3. The number on the control number sticker.

4. The installation date.

5. The content of the trouble, the abnormal condition (as detailed as possible). See “Troubleshooting” onpage 98.

6. The date you want the repair man to come.

Where to request repairs, and where to ask questions regarding after-sales service

Contact the dealer where you purchased the system bathroom, or INAX Maintenance Co., Ltd.

● Dealer where you purchased the product

● INAX Maintenance Co., Ltd.

TEL 7 0120-1794-11

Hours: 9:00 to 22:00

FAX 7 0120-1794-56

Home Page Address: http://www.i-mate.co.jp

Requests for repair accepted 365 days a year

ソレオ_P80-106_E 07.1.18 10:45 AM ページ99

Replacement Part No.

33,600 YenYFK-1275B(1)-D16,800 YenYFK-1275C(2)5,460 YenBL-S72119-KGeneral useStandard

bathtubSize1200 6,720 YenBL-SC72119-KFor push one way drain plugs


bathtubSize1300

7,350 YenBL-SC72129-KFor push one way drain plugs

34,650 YenYFK-1377B(1)-D17,850 YenYFK-1377C(1)6,090 YenBL-S77127-KGeneral use

Oval bathtub7,350 YenBL-SC77127-KFor push one way drain plugs

34,650 YenYFK-1387B(1)-D19,950 YenYFK-1387C(1)8,400 YenBL-S87127General useWide bathtub


bathtubSize1400






bathtubSize1600





Price including tax (shipping charged separately) Replacement Part No.

Price including tax (shipping charged separately) Replacement Part No.

Price including tax (shipping charged separately)

100

Replacement Parts Guide

About replacement parts

Following parts are available individually to be used for replacement at home.

■ Bath LidThe appropriate bath lid differs depending on the size of bathroom in your house.Refer to the following table when selecting a bath lid.

■ Bathtub Drain Plug

● Push one way drain plug

* A roll-up cover is not available for Ideatone bathtub (one with a deep transparent layer on the surface).* Product numbers and prices are subject to change.

Roll-up Cover Multi-piece Cover Multi-piece Cover exclusively for Thermo Bath

Replacement Part Name

Drain plug (White)

Drain plug (Stainless)

735 Yen

2,310 Yen

PBF-01-KCV2/DJ

PBF-01-KCV2/DM

Replacement Part No. Price including tax (shipping charged separately)

Drain core 84 YenPBF-01-KHC

● Rubber Plug


Rubber Plug

Drain core

Replacement Part No.

RC-5G-L500

PBF-5H-C2

Price including tax(shipping charged separately)

1,155 Yen

126 Yen

Replacem

entParts

GuideDrain plug

Drain core

Rubber Plug

Drain core

If the customer replaces the plug himself, exchange the ring connected to the chain. If the metal part mountedon the bathtub is removed, it could cause hot water to leak out of the bathtub.

ソレオ_P80-106_E 07.1.18 10:45 AM ページ100

101

■ The Safety Cover (With Hair Catcher) for Aqua-Jet For details, see the User’s Manual for aqua-jet.


Safety cover

(White)1,040 YenPJT-CIN121W


Do not use the aqua-jet if the safety cover is deformed or damaged. To safely use aqua-jet again,purchase the parts below.

Safety cover

(Black)PJT-CIN121B 1,040 Yen

■ Sponge Filter (Part for Using the Bathwater for Laundry System)

When a sponge filter is not clean even if washed, or if it becomes old, replace it regularly using thesponge filter attached as an accessory (5 pc set), When replacements run out, purchase the itembelow.

Specify the name and part No. of the replacement parts.

If you purchase parts from a dealer, etc.

Purchase from a dealer that sells INAX products.

If the home delivery service is used.

Your orders will be received by INAX MaintenanceHome Delivery Service Co., Ltd.(Payment of separate shipping charges isnecessary in the case of the home deliveryservice.)TEL 7 0120-00-1794

Hours: 9:00 to 17:00(except Saturdays, Sundays and holidays)

How to Purchase Replacement Parts

* If you need to know a part number, or if there are any other points that are unclear, contact the CustomerConsultation Center listed on the back cover.


Sponge filter

(5 pieces)840 YenSTC-SPN5



Extension cover 3,360 YenSTC-ELP


■ Extension Cover (Part for Using the Bathwater for Laundry System)

Following extension cover is available and can be exchanged at home, and customers can replaceit themselves.

Replacem

entParts

Guid

Replacement Parts Guide

ソレオ_P80-106_E 07.1.24 10:01 AM ページ101

102

After-sales ServiceA

fter-salesS

ervice

About the Warranty and Warranty Period

The waterproof performance of this system bathroom is covered by a 5-year warranty and performanceother than waterproof performance is covered by a 2-year warranty, counted from the date when the unit isdelivered to the construction company. However, repairs for some situations shall be chargeable, evenduring the warranty period. See Warranty (page 106) for details.

Parts Availability

The minimum parts availability period for replacement performance parts is 6 years after the product gotdiscontinued. For repairs after the parts availability period has expired, some parts may not be available, soplease understand.* Replacement performance parts are parts which are required in order to maintain the performance of that

product.

Periodic Inspection Recommended (Chargeable)

A periodic inspection is conducted on a chargeable basis, but it is recommended in the following cases.● After two years from the occupancy date. Even if there have been no problems with product performance,

the inspection is recommended to maintain the product performance for a long period of time.● If you live in an area with lots of hot springs or near the coast, etc. where it is particularly easy for

corrosion to occur.● A bathroom that has not been used for a long time, such as the one in a vacation home.Please consult with INAX Maintenance Co., Ltd. concerning the periodic inspection.The periodic inspection charges include the inspection fee (technical fee), travel expenses and parts costs (ifreplacement is required).

Introducing the Bathroom Refresh Plan (Chargeable)

At INAX Maintenance Co., Ltd., the following service is available on a chargeable basis.● [Total Bathroom Refresh] service: polishing of the ceiling, walls, floor, and metallic parts of water faucets,

using appropriate cleaners.Please feel free to inquire concerning these services.Use the following toll-free number to call if you have any questions concerning these and other services.

INAX Maintenance Co., Ltd.TEL 7 0120-1794-11Hours: 9:00 to 22:00FAX 7 0120-1794-56Home Page Address: http://www.i-mate.co.jp


ソレオ_P80-106_E 07.1.24 10:01 AM ページ102

103

After-sales Service

After-sales

Service

About Disposal

When disposing of the bathtub, request disposal for a company that has received certification.For details, consult the shop where you purchased this product.The principal materials used in the bathroom are as shown in the following table.

Part Type MaterialFRP (Calcium carbonate, Unsaturated polyester resin, glass fiber)

Ceramic, Cement based inorganic plates, steel tubingVinyl chloride resin metal laminated sheet or polyester resin metal laminated sheet, gypsum boardPolyester resin coated metal laminated sheet, gypsum boardBase material: FRP (Calcium carbonate, Unsaturated polyester resin, glass fiber), acryl resinBase material: Unsaturated polyester resin, glass frit, FRP (Calcium carbonate, unsaturated polyester resin, glass fiber)

Calcium carbonate, Unsaturated polyester resin, glass fiberPolystyrene

Top layer base material: ABS, acryl resin. Bottom layer base material: ABS, polystyrene

ABS resinBase material: ABS, acryl resin

FRPFRP (Calcium carbonate, Unsaturated polyester resin, glass fiber), tile (porcelain)Tile

TileSteel panel

–IdeatoneGrande V

Base material: Unsaturated polyester resin, Calcium carbonate, glass fiberSilfeFRP

–Methacrylic resinGUU Type

GTU & UDU TypesABS resinSSU Type

SDU TypeUXU Type

Floor

Wall

Ceiling

Bathtub

Apron

Counter

ソレオ_P80-106_E 07.1.18 10:45 AM ページ103

104

Bathtub Size and Volume

Bathtub Size

Maximum water volume and practical water volume differ, depending on the bathtub size. Practical

water volume is determined as the reference of the maximum water volum when a man is in the

bathtub, which is calculated as the maximum water volume minus 60L (the volume of 1 adult).

Standard bathtub

Maximum watervolume (L)

Practical watervolume (L)

Size

1200

260

200

Size

1300

280

220

Size

1400

300

240

Size

1600

300

240



Size

1300

320

280

Size

1400

345

285

Size

1600

370

310

Wide bathtub

1300～1600 (mm)



Size

1300

250

190

Size

1400

275

215

Size

1600

300

240

Oval bathtub

1300～1600 (mm)

1200～1600 (mm)

Bathtub

Size

ソレオ_P80-106_E 07.1.18 10:45 AM ページ104

105

ソレオ_P80-106_E 07.1.18 10:45 AM ページ105

Warranty

Certificate

106

Warranty Certificate

Product type name

Customer

Warranty Period2 years from the installation delivery date.

However, waterproof performance* is covered for 5 years from the installation delivery date.* Waterproof performance is “Ability to prevent water leakage to outside the bathroom, from walls, floor, etc.”

Name:

Installation delivery date

Address:Á –

Tel: ( ) –

Year Month Day

Address: Á –

Shop that handled or

sold the product

Series name

System Bathroom

SOLEO

Seal

To the customer,The Warranty Certificate is not issued again, so carefully store it so that it is not lost.Individual customer information entered in the warranty certificate is used for free repair service during the warrantyperiod, and safety inspection activity after the warranty period.

Free Repair Provisions (Warranty Provisions)1. Breakdowns during the warranty period are repaired for free, if used and maintained normally in accordance with written

cautions in the “User’s Manual”, “Caution labels”, etc.2. When receiving free repair, request at the shop entered in this document that handled or sold the product, and present

this document.3. If you cannot request repair at the shop entered in this document that handled or sold the product, please consult with the

Customer Consultation Center noted in this User’s Manual, or with a nearby INAX branch or sales office.4. This document is only valid in Japan.

* This warranty certificate promises to provide free service according to the period and conditions noted in thisdocument. Moreover, this document does not limit the customer’s legal rights.

* For repairs after the warranty period is over, or if there are any unclear points, please consult with the shop entered inthis document that handled or sold the product, or with the Customer Consultation Center noted in this document, orwith a nearby INAX branch or sales office.

{Exempted Items}Repairs for the following items shall be on a chargeable basis, even during the warranty period.1. Trouble such as breakdown or damage when the product was not used according to its purpose (vehicle, ship, extremely

frequent business use, etc.).2. Trouble resulting from installation or construction not done by an authorized installer, not according to the installation instructions, etc.3. Breakdown and trouble resulting from a customer neglecting to use or maintain appropriately.4. Trouble resulting from a person other than a professional installer moving, repairing, disassembling or otherwise handling the product.5. Product trouble resulting from a problem which was not the fault of the product, such as building structure deformity

(insufficient strength, warping).6. Troubles from changes due to aging and use, such as appearance (fading, rust stains, etc.), wear of disposable parts

accompanying product use, etc.7. Troubles caused by a polluted environment (smoke, salt damage, sand, dust, various metallic particles, various gases

including hydrogen sulfide gas), or by a corrosive air environment near the coast, hot spring area, etc.8. Trouble caused by damage from actions of small animals (dogs, cats, mice, insects, or other animals), or by plants (vines, roots, etc.).9. Breakdown and damage from trouble caused by disasters (accidents such as fire or explosion, lightning, earthquake,

volcanic eruption, wind or water disaster, tidal wave, landslide, freezing, snow damage, etc.).10. Damage and trouble caused by illegal acts, or by destructive acts such as war or riot.11. Phenomena such as condensation, water soaking through, or rust caused by natural phenomena or the living environment.12. Breakdown and damage due to disposable parts (seals), clogs from foreign matter in pipes, etc.13. Breakdown and damage trouble caused by supplying water such as hot spring water or well water, which does not

comply with drinking water quality standards stipulated in tap water related laws and regulations.14. Trouble caused by the use of cleansers or chemicals which have a detrimental influence on plastics and metals.15. Breakdown and damage due to freezing of parts in the case that the parts were not cold area specification parts.16. Trouble caused by water scum adherence, or by the inflow of rust, sand, dirt, or other foreign matter from cold or hot water pipes.17. Trouble from breakdown or damage caused by an environment other than specified for the supply of gas, electricity,

water, etc. (unusual gas pressure, unusual electrical source or voltage or frequency, unusual magnetic waves, unusualwater pressure or quality, sounds, vibrations, etc.).

18. Trouble caused by use of gas, electricity, fuel, etc. which was of other than the specified rating.19. Adjustments, etc. accompanying temperature changes.20. If the warranty certificate expires or is not presented.21. If the installment date, customer name, or name of the shop that handled the product are not entered in this document, or

if the information has been rewritten.22. Inadequate management, etc. during the period from completion of construction until moving into the home.

ソレオ_P80-106_E 07.1.29 0:01 PM ページ106

GPU-0204(07010)

Dealer

Inquiries concerning product use, cleaning methods, etc. and about products

Contact the shop where you purchased your product or

To request repairs (Please read the section in this manual “After-sales Service.”)

Contact INAX Maintenance Co., Ltd.

TEL 0120-1794-11Hours 9:00 to 22:00

FAX 0120-1794-56Home Page Address: http://www.i-mate.co.jp

INAX Corporation Customer Consultation Center

TEL 0120-1794-00Hours Weekdays 9:00 to 19:00

Saturdays, Sundays, Holidays 10:00 to 18:00(Excluding summer vacation and the year end/new year vacation)

FAX 0120-1794-30


INAX Home Page Address: http://www.inax.co.jp/

ソレオ_表4_E 07.1.17 1:49 PM ページ1

system bathroom soleo - lixil

Documents