table of contents · 2012. 4. 26. · phone: (281) 664 - 7800 (800) 890 - 7827 fax: (281) 664 -...

10002 Sam Houston Center Drive Houston, TX 77064 Phone: (281) 664 - 7800 (800) 890 - 7827 Fax: (281) 664 - 7850 www.spirstar.com

TABLE OF CONTENTSA. General Information

1. Advantages of SPIR STAR Thermoplastic Hose 2. Care and Use Instructions 3. Hose Denomination 4. Hose Assembly Part Number System 5. Decimal and Millimeter Equivalent Chart 6. Hose Applications per Hose Type

B. Type 2 Series Hose

C. Type 2K Series Hose

D. Type 2W Series Hose

E. Type 2WL Series Hose

F. Type 2OK Series Hose

G. Type 3 Series Hose

H. Type 4 Series Hose

I. Type 6 Series Hose

J. Type 6H Series Hose

K. Type 8 Series Hose

L. Type F Series Hose


M. Type HT Series Hose

N. Type LTKE Series Hose

O. Type M Series Hose

P. Type PPA Series Hose

Q. Type R Series Hose

R. Type UHP Series Hose

S. Type WL Twin Series Hose

T. Accessories

U. Hose Data

1. Recommended Tightening Procedures2. Chemical Resistance Chart

V. Terms and Conditions

TABLE OF CONTENTS


GENERAL INFORMATION

º º

™

Advantages of SPIR

STAR

Thermoplastic H

ose

Chemical Resistance:................. to almost all chemicals, detergents and solvents.

High Temperature Stability:....... ranging between -22 F to 392 F according to materials

Weight Savings:.......................... up to 50% reduction in weight with regard to comparable rubber hose.

Weather Resistant:...................... to ozone and ultraviolet light.

Aging Resistance:........................ even with frequent change of environmental influences, decomposition does not occur.

Volumetric Expansion:................extremely low even at maximum working pressure allowing for faster response time.

External Pressure Collapse:......high collapse resistance due to wire reinforcement, allows use in deepwater projects.

Minimal Pressure Drop:..............friction loss is reduced due to smooth inner core.

Impulse Resistant:.......................unique spiralized construction decreases fatigue thus maximizing service life.

Abrasion Resistant:....................Duralife outer cover reduces abrasion and wear by up to 40%.

Low Permeation Rate:.................to most gaseous media and chemicals such as methanol.

Seawater Resistant:....................outer cover is resistant against hydrolysis and microbes.

Kink Resistant:............................ advanced construction techniques offer greater flexibility while protecting the hose from kinks.


GENERAL INFORMATION

The following is SPIR STAR’s list of Do’s & Don’ts for the proper and safe handling of high pressure hose.The improper use of high pressure hose can cause serious injury or property damage. NEVERhandle a leaking hose assembly. Treat any injury from high pressure fluid seriously and seekimmediate medical attention.

Do’s:

Treat high pressure hose with extreme caution. SPIR STAR hoses are wire reinforced hoses, not garden hoses and shouldbe treated with the same care as a high pressure containment vessel.When using hoses for waterjetting, read and understand RecommendedPractices for the Use of Manually Operated High Pressure Waterjet Equipment (Waterjet Technology Association, 314-241-1445, www.wjta.org) prior to use.Always visually inspect the hose for damage, cuts, or wear spots before using.Check the hose end connections and threads for wear, rust, cracks, mechanical abuse, or other deterioration which couldproduce a dangerous projectile.Know the working and burst pressures of the hose before putting it in service.Always use clean, filtered water to prolong hose life. Some plants’ water sources are high in sulfur which attacks stainlesssteel.Always clean, drain, and coil hoses after use. Soap and water usually provide an excellent cleaning agent.Always wear protective gloves, eyewear, and garments when handling high pressure hose and waterjet lances.

Don’t use a hose that has cuts, damage, or wires showing through the outer cover.Don’t use a hose that has been kinked.Don’t use a hose that has bubbles or blisters in the outer cover.Don’t exceed the bend radius or pressure rating for each hose.Don’t run over or crush the hose with heavy vehicles.Don’t use a hose with corroded or leaking end connections. Take them out of service immediately.Don’t use hose that has been exposed to chemical attack or over temperature.Don’t bend the hose over scaffolding or pull heavy equipment with the hose.Don’t mechanically rotate the hose without using a slip-clutch device.Don’t let hose support its own weight off towers or buildings.Avoid using dirty water or water with sulfur compounds in it. Tests have documented that hoses fail more rapidly whenusing water sources from chemical plants and refineries.Don’t expect water jetting or hydraulic hose to last forever.

Don’ts:

Care and U

se of High Pressure H

ose

Be Safe - Replace!


GENERAL INFORMATION

5/6Hinner diameter in mm

number of spiral layers

series description

E = stainless steel wireF = PTFE inner coreH = reinforced typeHCR = external pressure resistantHT = suitable for extremely high temperaturesK = braided layerL = particularly flexibleM = special treated PA11 inner core for Offshore applicationsPPA = PVDF inner core/polyamide outer coverR = reinforced outer coverS = seawater resistant stainless steelT = aramide fiberW = open spiral layer

Hose D

enomination

21=1-5/16

14 - 7/8-1416=1”-12


GENERAL INFORMATION

HoseAssembly

Length

F or I =Feet orInches

HoseType

End Fitting = TM = Type F Swivel J = JIC Female Swivel NPT = National Pipe Male MN = Medium Pressure Tube Nipple Male HN = High Pressure Tube Nipple Male

Material = Leave blank for normal carbon fittings SS = Stainless Steel Add 316 after SS for Offshore jobs

Special Items=C = Abrasion CoverB = Burst ShieldCG = Containment GripW = Whip CheckBR = Bend RestrictorSPR = Spring GuardsSG = Support Grip

Size =

Type M NPT Tube Nipple JIC9=9/16-18 4=1/4 4=1/4-28 4=7/16-2012=3/4-16 6=3/8 6=3/8-24 6=9/16-18

8=1/2 9=9/16-18 8=3/4-16 12=3/4 12=3/4-12 10=7/8-14

16=1 12=1-1/16-12 16=1-5/16-12

* = If the hose requires different end fittings, list them both in the part number Example: A 6/2W hose 50 feet long with Type M 9/16 and 1/4HP Tube Nipple would be H6/2W050FTM9HN4

H 5/4 000 F or I End Fitting Size* Material Special

Hose A

ssembly Part N

umber System


GENERAL INFORMATION

Fractions Decimalsof an inch of an inch Millimeters

Fractions Decimalsof an inch of an inch Millimeters

33/64 0.515625 13.1017/32 0.53125 13.4935/64 0.546875 13.899/16 0.5625 14.2937/64 0.578125 14.6819/32 0.59375 15.0839/64 0.609375 15.485/8 0.625 15.8841/64 0.640625 16.2721/32 0.65625 16.6743/64 0.671875 17.0711/16 0.6875 17.4645/64 0.703125 17.8623/32 0.71875 18.2647/64 0.734375 18.653/4 0.75 19.0549/64 0.765625 19.4525/32 0.78125 19.8451/64 0.796875 20.2413/16 0.8125 20.6453/64 0.828125 21.0327/32 0.84375 21.4355/64 0.859375 21.837/8 0.875 22.2357/64 0.890625 22.6229/32 0.90625 23.0259/64 0.921875 23.4215/16 0.9375 23.8161/64 0.953125 24.2131/32 0.96875 24.6163/64 0.984375 25.001 1.0 25.40

Decim

al & M

illimeter Equivalent C

hart

1/64 0.015625 0.3971/32 0.03125 0.7943/64 0.046875 1.1911/16 0.0625 1.5885/64 0.078125 1.9843/32 0.09375 2.3817/64 0.109375 2.7781/8 0.125 3.1759/64 0.140625 3.5725/32 0.15625 3.96911/64 0.171875 4.3663/16 0.1875 4.76313/64 0.203125 5.1597/32 0.21875 5.55615/64 0.234375 5.9531/4 0.25 6.35017/64 0.265625 6.7479/32 0.28125 7.14419/64 0.296875 7.5415/16 0.3125 7.93821/64 0.328125 8.33411/32 0.34375 8.73123/64 0.359375 9.1283/8 0.375 9.52525/64 0.390625 9.92213/32 0.40625 10.3227/64 0.421875 10.727/16 0.4375 11.1129/64 0.453125 11.5115/32 0.46875 11.9131/64 0.484375 12.301/2 0.5 12.70


3/2 Waterblasting W.P. 14,5000 psi Heat Exchanger Tube Cleaning with Duralife Flex™ Outer Cover

Hydraulics Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels

3/4 Waterblasting W.P. 29,000 psi Ultra High Pressure Waterblast Tube Cleaning


3/6 Waterblasting W.P. 40,600 psi Ultra High Pressure Waterblast Tube Cleaning




4/2K Hydraulics W.P. 17,400 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels

4/2W Hydraulics W.P. 20,300 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels Rescue Tools

Hose Type

GENERAL INFORMATION

Product Applications per H

ose Type


4/4 Waterblasting W.P. 31,320 psi Heat Exchanger Tube Cleaning with 20K Blast Pro End Fittings


4/6 Waterblasting W.P. 40,600 psi Automated Cleaning Booths Paint Removal Rotating Cleaning Device for Waterblast Surface Preparation Ultra High Pressure Waterblast Tube Cleaning Ultra High Pressure Waterjet Table Cutting

Hydraulics Pressure Testing for Valves, Tooling and Control Panels Bolt Tensioning and Torque Tools Hydraulic Jacks

4/8 Waterblasting W.P. 46,400 psi Automated Cleaning Booths Paint Removal Ultra High Pressure Waterblast Tube Cleaning Ultra High Pressure Waterjet Table Cutting




5/2OK Waterblasting W.P. 15,000 psi Heat Exchanger Tube Cleaning with stainless steel overbraid cover


GENERAL INFORMATION


ose Type





Hydraulics Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels Rescue Tools

Oil and Gas Gaseous Media Handling Grease Injection Hydraulic Control Nitrogen Service

5/4HT Special Service W.P. 18,630 psi High Temperature to 300ºF

Oil and Gas Chemical Injection Gaseous Media Handling Methanol Injection Nitrogen Service

5/6 Waterblasting W.P. 36,250 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Rotating Cleaning Device for Waterblast Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterblast Tube Cleaning Ultra High Pressure Waterjet Table Cutting

GENERAL INFORMATION


ose Type


5/6 cont’d. Hydraulics Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Hydroforming

Pressure Testing for Valves, Tooling and Control Panels

5/6H Waterblasting W.P.40,600 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Rotating Cleaning Device for Waterblast Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterblast Tube Cleaning Ultra High Pressure Waterjet Table Cutting

Hydraulics Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Hydroforming


5mm UHP Waterblasting W.P.46,400 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterjet Table Cutting

Hydraulics Hydroforming




GENERAL INFORMATION


ose Type


6/2OK Waterblasting W.P. 14,500 psi Heat Exchanger Tube Cleaning with stainless steel overbraid cover


6/2K Hydraulics W.P. 16,240 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Rescue Tools

Oil and Gas Grease Injection Hydraulic Control

6/2LTKE Oil and Gas W.P. 7,540 psi Sub Sea Well Control Hydraulic Control


Oil and Gas Gaseous Media Handling Grease Injection Hydraulic Control Nitrogen Service Sub Sea Well Control

6/2WHT Special Service W.P. 13,260 psi High Temperature to 300ºF


GENERAL INFORMATION


ose Type


6/2WL Hydraulics W.P. 17,400 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels Rescue Tools

6/2WL Twin Hydraulics W.P. 17,400 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels Rescue Tools

6/2WM Special Service W.P. 15,660 psi Nylon 11 Core for NACE Class 6 Cleanliness Standard

Oil and Gas Chemical Injection Hydraulic Control Methanol Injection Nitrogen Service Sub Sea Well Control

6/2WPPA Special Service W.P. 13,260 psi Chemical Transfer and Permeation Resistance

Oil and Gas Chemical Injection Gaseous Media Handling Hydraulic Control Methanol Injection Nitrogen Service Sub Sea Well Control



GENERAL INFORMATION


ose Type



Hydraulics Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels Rescue Tools




6/4LTKE Oil and Gas W.P. 10,000 psi Sub Sea Well Control Hydraulic Control

6/4PPA Special Service W.P. 15,730 psi Chemical Transfer and Permeation Resistance

Oil and Gas Chemical Injection Gaseous Media Handling Hydraulic Control Methanol Injection Nitrogen Service Sub Sea Well Control Ultra High Pressure Waterjet Table Cutting

Hydraulics Controls for Service Equipment Pressure Testing for Valves, Tooling and Control Panels

GENERAL INFORMATION


ose Type


6/6H Waterblasting W.P. 40,600 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Rotating Cleaning Device for Waterblast Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterblast Tube Cleaning

6mm UHP Waterblasting W.P. 46,400 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterjet Table Cutting

Hydraulics Pressure Testing for Valves, Tooling and Control Panels




8/2PPA Special Service W.P. 8,260 psi PVDF Chemical Resistant Inner Core Material


GENERAL INFORMATION


ose Type




8/2WHT Special Service W.P. 10,800 psi High Temperature to 300ºF


8/2WL Hydraulics W.P. 14,500 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels Rescue Tools

8/2WL Twin Hydraulics W.P. 17,400 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels Rescue Tools

GENERAL INFORMATION


ose Type


8/2WR Special Service W.P. 15,080 psi Heavy Duty Outer Cover for Rough Service

Waterblasting Rotating Cleaning Device for Waterblast Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose

Oil and Gas Gaseous Media Handling Grease Injection Nitrogen Service



Hydraulics Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels




GENERAL INFORMATION


ose Type




Methanol Injection Nitrogen Service Sub Sea Well Control

8/6 Waterblasting W.P. 30,450 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Robotic Surface Cleaning of Ships

Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterjet Table Cutting


8/6H Waterblasting W.P. 36,250 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterjet Table Cutting



GENERAL INFORMATION


ose Type

8/4PPA cont’d.


8/4PPA Special Service W.P. 15,730 psi Chemical Transfer and Permeation ResistanceOil and Gas Chemical Injection Gaseous Media Handling Hydraulic Control


8/6R Special Service W.P. 30,450 psi Heavy Duty Outer Cover for Rough Service

Waterblasting Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Paint Removal Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Waterblast Supply Hose

8/8 Waterblasting W.P. 40,600 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterblast Table Cutting



8mm UHP Waterblasting W.P. 46,400 psi Automated Cleaning Booths Hydro Demolition of Concrete Paint Removal Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Ultra High Pressure Waterjet Table Cutting


ose Type

GENERAL INFORMATION 8/6HR Special Service W.P. 36,250 psi

Heavy Duty Outer Cover for Rough ServiceWaterblasting Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Paint Removal Robotic Surface Cleaning of Ships Surface Preparation Tank and Vessel Cleaning Waterblast Supply Hose



Oil and Gas Grease Injection Hydraulic Control Nitrogen Service






ose Type

GENERAL INFORMATION Hydraulics

Hydroforming Pressure Testing for Valves, Tooling and Control Panels

10/2 Waterblasting W.P. 10,000 psi

Large Bore Pipe Tube CleaningHydraulics Pressure Testing for Valves, Tooling and Control Panels

8mm UHP (cont.d)


Hydraulics Controls for Service Equipment Hydraulic Jacks Pressure Testing for Valves, Tooling and Control Panels






10/6 Waterblasting W.P. 27,840 psi Automated Cleaning Booths Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Paint Removal Surface Preparation Robotic Surface Cleaning of Ships Tank and Vessel Cleaning Waterblast Supply Hose


ose Type

GENERAL INFORMATION 10/4 Waterblasting W.P. 21,750 psi

Heat Exchanger Tube Cleaning with 20K Blast Pro End Fittings Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose


13/2 Waterblasting W.P. 10,000 psi Automated Cleaning Booths Large Bore Pipe Tube Cleaning Paint Removal Tank and Vessel Cleaning Waterblast Supply Hose


Oil and Gas Grease Injection

13/2KR Special Service W.P. 11,600 psi Heavy Duty Outer Cover for Rough Service

Waterblasting Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose


Oil and Gas Grease Injection

13/2W Hydraulics W.P. 15,080 psi Bolt Tensioning and Torque Tools Controls for Service Equipment Hydraulic Jacks Instrumentation Packages for gauges Pressure Testing for Valves, Tooling and Control Panels



ose Type



10/6 (cont.d)


13/2WR Special Service W.P. 15,080 psi Heavy Duty Outer Cover for Rough Service

Waterblasting Large Bore Pipe Tube Cleaning Rotating Cleaning Device for Waterblast Tank and Vessel Cleaning Waterblast Supply Hose


Oil and Gas Gaseous Media Handling Grease Injection Nitrogen Service

13/4 Waterblasting W.P. 18,560 psi Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose

Hydraulics Controls for Service Equipment Hydraulic Jacks Pressure Testing for Valves, Tooling and Control Panels



ose Type

GENERAL INFORMATION 13/2WM Special Service W.P. 13,340 psi

Nylon 11 Core for NACE Class 6 Cleanliness StandardOil and Gas Chemical Injection Hydraulic Control Methanol Injection Nitrogen Service Sub Sea Well Control


13/4HHT Special Service W.P. 15,080 psi High Temperature to 300ºF


13/4HPPA Special Service W.P. 15.080 psi Chemical Transfer and Permeation Resistance



Hydraulics Controls for Service Equipment Hydroforming

Oil and Gas Grease Injection Nitrogen Service


ose Type

GENERAL INFORMATION 13/4H Waterblasting W.P. 20,300 psi

Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Rotating Cleaning Device for Waterblast Tank and Vessel Cleaning Waterblast Supply Hose




13/6HR Special Service W.P. 27,840 psi Heavy Duty Outer Cover for Rough Service

Waterblasting Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose


Oil and Gas Gaseous Media Handling Nitrogen Service

13/8HR Special Service W.P. 30,740 psi Heavy Duty Outer Cover for Rough Service

Waterblasting Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose





ose Type

GENERAL INFORMATION 13/6H Waterblasting W.P. 27,840 psi

Hydro Demolition of Concrete Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose

Hydraulics Controls for Service Equipment Hydroforming





Oil and Gas Chemical Injection Gaseous Media Handling Grease Injection Hydraulic Control Nitrogen Service

20/2 Waterblasting W.P. 7,540 psi Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose



20/2W Hydraulics W.P. 11,020 psi Controls for Service Equipment Hydraulic Jacks Pressure Testing for Valves, Tooling and Control Panels



ose Type


Controls for Service Equipment Pressure Testing for Valves, Tooling and Control Panels


16/4 (cont.d)






20/6 Waterblasting W.P. 20,300 psi Large Bore Pipe Tube Cleaning Rotating Cleaning Device for Waterblast Tank and Vessel Cleaning Waterblast Supply Hose


Oil and Gas Nitrogen Service Gaseous Media Handling




ose Type

GENERAL INFORMATION 20/4 Waterblasting W.P. 15,080 psi

Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose


25/2 Waterblasting W.P. 6,380 psi Large Bore Pipe Tube Cleaning Waterblast Supply Hose


Oil and Gas Nitrogen Service

25/2K Hydraulics W.P. 6,960 psi Pressure Testing for Valves, Tooling and Control Panels

Oil and Gas Grease Injection Hydraulic Control Nitrogen Service

25/2KM Special Service W.P. 7,250 psi Nylon 11 Core for NACE Class 6 Cleanliness Standard


25/2W Hydraulics W.P. 9,280 psi Controls for Service Equipment Hydraulic Jacks Pressure Testing for Valves, Tooling and Control Panels

Oil and Gas Gaseous Media Handling Grease Injection Hydraulic Control Sub Sea Well Control


ose Type

GENERAL INFORMATION


25/4 Waterblasting W.P. 13,050 psi Large Bore Pipe Tube Cleaning Tank and Vessel Cleaning Waterblast Supply Hose



25/4PPA Special Service W.P.10,000 psi Chemical Transfer and Permeation Resistance



ose Type

GENERAL INFORMATION


Hose Type

6/2KF Hot Melt Adhesives / Hot Glue Dispensing W.P. 7,250 psi Injection Molding Chemical Transfer / Paint Transfer Robotic Systems Compressed Gas




16/2KF Hot Melt Adhesives / Hot Glue Dispensing W.P 5,800 psi Injection Molding Chemical Transfer / Paint Transfer Robotic Systems Compressed Gas




ose Type

GENERAL INFORMATION

Hose Type 3/2 Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]

∅ ID ∅ OD Working Pressure*)

Burst Pressure ¹)

Min. Bend Radius Weight Nipple

∅ ID Sleeve Sleeve ∅ OD

0,13 inch 0,27 inch 14.500 psi 36.250 psi 2,36 inch 0,048 lbs/ft 0,08 inch 0,35 inch

3,4 mm 6,9 mm 1.000 bar 2.500 bar 60 mm 0,072 kg/m 2,0 mm 10320101 carbon steel 8,9 mm

Fittings: ID3, Series A and X Description Size Material Part Number

male fitting one piece waterblast 1/16”x27 NPTF carbon steel 30320402X / 30320402/1X

male fitting one piece waterblast M6x1 carbon steel 30320101X / 30320101/1X

BSP female swivel G1/4” carbon steel AISI 316Ti

20320302A / 50540301 swivel nut / 50540305

----- Additional fittings are available upon request. -----

¹)Production related variations up to 5 % are possible *) The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice.

© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 4/2 Duralife Flex™ Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels

¹)Production related variations up to 5 % are possible *) The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice. ©

Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200

8

Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




4,0 mm 8,0 mm 1.200 bar 3.000 bar 75 mm 0,110 kg/m 2,5 mm

10420101 carbon steel 10420105

AISI 316Ti 10,1 mm


HP fitting 1/4”x28UNF LH AISI 316Ti 40420205A



male fitting one piece waterblast 5/16”x24 UNF carbon steel 30420601X / 30420452/1X male fitting 1/16”x27 NPTF carbon steel 30420412A

male fitting 1/8”x27 NPTF carbon steel 30420542A


male fitting G1/8” carbon steel 30420302A

male fitting flat seal nozzle type G1/8” carbon steel 30420382A


male fitting USIT®-Ring G1/4” carbon steel 30420351A

male fitting M7 carbon steel 30420042A

male fitting flat seal nozzle type M7 carbon steel 30420082A


male fitting M10x1 carbon steel 30420002A

BSP female swivel G1/4” carbon steel carbon steel AISI 316Ti

20430302A swivel nut / 50540301 swivel nut / 50540305

metric female swivel with O-Ring M24x1.5 carbon steel 20420042A / 51360201

Type M female swivel 9/16”x18 UNF carbon steel carbon steel

20420642A swivel nut / 50540601


Hose Type 5/2 Duralife Flex™ Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)



0,20 inch 0,37 inch 15.080 psi 37.700 psi 3,74 inch 0,084 lbs/ft 0,12 inch 0,14 inch1) 0,51 inch

5,0 mm 9,4 mm 1.040 bar 2.600 bar 95 mm 0,125 kg/m 3,0 mm 3,5 mm1)

10520101 carbon steel

12,9 mm


male fitting one piece waterblast 1/8”x27 NPTF carbon steel 30520442X /30520442/1X









Type M female swivel 9/16"x18 UNF carbon steel AISI 316Ti

20520601A / 50540601 swivel nut / 50540605

metric female swivel G1/4” carbon steel AISI 316Ti

20520301A / 50540301 swivel nut / 50540305

metric female swivel M14x1.5 carbon steel 20520101A / 50540101



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

13.

06.2

008



Burst Pressure ¹)





Fittings: ID6, Series A ,X and WX Description Size Material Part Number

male fitting one piece waterblast 1/4”x18 NPTF carbon steel 30620469WX / 30620462/1X

male fitting one piece waterblast G1/4” carbon steel 30620369X / 30620462/1X



male fitting 1/4”x18 NPTF AISI 316Ti 30620405A



male fitting with 60° cone G1/4” carbon steel 30620341A

male fitting for USIT®-Ring G1/4” carbon steel 30620391A

male fitting DIN3852 T2 form A G1/4” carbon steel 30620301A




BSP female swivel G1/4” carbon steel 20620301A / 50540301

BSP female swivel G1/4” AISI 316Ti 20620305A / 50540305 metric female swivel with O-Ring M18x1.5 carbon steel 20620241A / 50620201

metric female swivel with O-Ring M22x1.5 carbon steel carbon steel AISI 316Ti



Type M female swivel 9/16"x18 UNF carbon steel 20620641A / 50540601

Type M female swivel 9/16"x18 UNF AISI 316Ti 20620645A / 50540605

JIC female swivel 9/16”x18 UNF AISI 316Ti S20630615A / S5063615

female fitting 1/4“x18 NPTF carbon steel 30620441A



metric female swivel M16x1.5 AISI 316Ti 20620145A / 50620125




Burst Pressure ¹)




8,1 mm 13,3 mm 840 bar 2.100 bar 130 mm 0,200 kg/m 5,5 mm 10820101 carbon steel 17,8 mm




male fitting one piece waterblast G1/4” carbon steel 30820361X / 30820441/1X male fitting 1/4”x18 NPTF carbon steel 30820411A



male fitting with 60°cone G1/4” carbon steel 30820321A







Type M female swivel 3/4”x16 UNF AISI 316Ti AISI 316Ti

carbon steel


JIC female swivel 9/16”x18 UNF carbon steel 20820601A / 50820601

JIC female swivel 9/16”x18 UNF AISI 316 Ti carbon steel

20820605A swivel nut / 50820601



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 8/2 PA Duralife Flex™ Applications Waterblasting: Tube Cleaning, Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing, Tooling and Control Panels Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)











male fitting with 60°cone G1/4” carbon steel 30820321A








carbon steel




20820605A swivel nut / 50820601


Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200

8 ----- Additional fittings are available upon request. -----

Hose Type 10/2 Applications Waterblasting: Large Bore Pipe Tube Cleaning Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





Fittings: ID10, Series A Description Size Material Part Number


male fitting 3/8”x18 NPTF AISI 316 Ti 31020405A

male fitting 1/2”x14 NPT AISI 316 Ti 31020425A




BSP female swivel G1/2” AISI 316 Ti 21020305A / 51060315

metric female swivel with O-Ring M22x1.5 carbon steel carbon steel AISI 316 Ti


Type M female swivel 3/4”x16 UNF AISI 316 Ti AISI 316 Ti

21020645A swivel nut / 51320615



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/2 Applications Waterblasting: Paint Removal, Tank & Vessel Cleaning, Automated Cleaning Booths, Waterblast Supply Hose, Large Bore Tube Cleaning Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Grease Injection Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)












Type M female swivel 1"x12 UNF carbon steel 21320641A / 51360641

Type M female swivel 1"x12 UNF AISI 316Ti AISI 316Ti AISI 303




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 20/2 Applications Waterblasting: Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Grease Injection, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





Fittings: ID 20, Series A Description Size Material Part Number

male fitting 1”x 11 1/2 NPT carbon steel 32020421A

male fitting 1”x 11 1/2 NPT AISI 316Ti 32020425A

metric female swivel with O-Ring M36x2 carbon steel 22020201A / 52040201

Type M female swivel 1 5/16”x12 UN AISI 316Ti AISI 316Ti

22020645A swivel nut / 52040645

JIC female swivel 1 5/16”x12 UN AISI 316Ti AISI 316Ti

22020605A swivel nut / 52040605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 25/2 Applications Waterblasting: Large Bore Pipe Tube Cleaning, Waterblast Supply Hose Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






male fitting 1”x11 ½ NPTF carbon steel 32520411A

male fitting 1”x11 ½ NPTF AISI 316Ti 32520415A




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 4/2K Applications Hydraulics: Bolt Tensioning and Torque Tools, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





10430101 carbon steel 10430105

AISI 316Ti 13,1 mm


HP fitting 1/4”x28 UNF LH AISI 316Ti 40420205A












BSP female swivel G1/4” carbon steel carbon steel AISI 316TI




20420642A swivel nut / 50540601


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Hose Type 6/2K Applications Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Hydraulic Tools Oil and Gas: Grease Injection, Hydraulic Control


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




6,2mm 12,9 mm 1.120 bar 2.800 bar 95 mm 0,300 kg/m 4,0 mm 10630101 carbon steel 16,2 mm


























Hose Type 10/2K Applications Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Hydraulic Tools Oil and Gas: Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire 1 layer of braided steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)
















21020645A swivel nut / 51320615



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 25/2K Applications Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Grease Injection, Nitrogen Service, Hydraulic Control Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





Fittings: ID 25, Series A and S Description Size Material Part Number

male fitting 1”x11 ½ NPTF carbon steel 32520411A

male fitting 1”x11 ½ NPTF AISI 316Ti 32520415A



22530645S / 52530645 12530245 (Sleeve)


22530605S / 52530605 12530245 (Sleeve)



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 4/2W Applications Hydraulics: Bolt Tensioning and Torque Tools, Controls for Service Equipment, Hydraulic Jacks, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels, Hydraulic Tools Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





10430101 carbon steel 10430105

AISI 316Ti 13,0 mm


HP fitting 1/4”x28 UNF LH AISI 316Ti 40420205A
















20420642A swivel nut / 50540601


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2


Hose Type 6/2W Applications Waterblasting: Tube Cleaning, Heat Exchanger Cleaning Hydraulics: Bolt Tensioning Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing, Tooling and Control Panels


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





10630191W carbon steel

10630195W AISI 316Ti

15,4 mm


























Hose Type 8/2W Applications Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels, Hydraulic Tools Oil an Gas: Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service, Sub Sea Well Control Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




8,0 mm 14,3 mm 1.040 bar 2.600 bar 110 mm 0,314 kg/m 5,5 mm 10830191W

carbon steel 18,3 mm













carbon steel




20820605A swivel nut / 50820601



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 10/2W Applications Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels, Hydraulic Tools Oil and Gas: Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service, Sub Sea Well Control Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






11030195W AISI 316Ti

21,5 mm












21020645A swivel nut / 51320615



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/2W Applications Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service, Sub Sea Well Control Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






11330195W AISI 316Ti

26,70 mm








Type M female swivel 1"x12 UNF carbon steel 21320641A / 51360641

Type M female swivel 1"x12 UNF AISI 316Ti AISI 316Ti AISI 303



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Hose Type 20/2W Applications Hydraulics: Controls for Service Equipment, Hydraulic Jacks, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service, Sub Sea Well Control Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




18,8 mm 29,5 mm 760 bar 1.900 bar 220 mm 1,160 kg/m 13,0 mm 12020191W



male fitting 1”x 11 1/2 NPT carbon steel 32020421A

male fitting 1”x 11 1/2 NPT AISI 316Ti 32020425A



22020645A swivel nut / 52040645


22020605A swivel nut / 52040605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 25/2W Applications Hydraulics: Controls for Service Equipment, Hydraulic Jacks, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




25,0 mm 35,6 mm 640 bar 1.600 bar 280 mm 1,490 kg/m 16,5 mm 12530111W


Fittings: ID 25, Series T Description Size Material Part Number

metric female swivel with O-Ring M42x2 carbon steel 22530201T / 52520201



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6/2WL Applications Hydraulics: Bolt Tensioning Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing, Tooling and Control Panels


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






10630195W AISI 316TI

15,5 mm


























Hose Type 8/2WL Applications Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels, Hydraulic Tools Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)


















carbon steel




20820605A swivel nut / 50820601



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 5/2OK Applications Waterblasting: Tube Cleaning, Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Top Cover: 1 braided layer of stainless steel wireTemperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)



0,20 inch 0,37 inch 15.080 psi 37.700 psi 3,74 inch 0,148 lbs/ft 0,14inch 0,52 inch

5,0 mm 10,8 mm 1.040 bar 2.600 bar 95 mm 0,220 kg/m 3,5 mm 30530451KX


Fittings: ID5, Series KX Description Size Material Part Number

male fitting one piece waterblast 1/8”x27 NPTF carbon steel 30530451KX / 30520442/1X


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Hose Type 6/2OK Applications Waterblasting: Tube Cleaning, Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Top Cover: 1 braided layer of stainless steel wireTemperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




6,2 mm 13,1 mm 1.000 bar 2.500 bar 110 mm 0,306 kg/m 4,0 mm 30630451KX

carbon steel 15.0 mm

Fittings: ID6, Series KX Description Size Material Part Number

male fitting one piece waterblast 1/4”x18 NPTF carbon steel 30630451KX / 30620462/1X



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 5/3 Duralife Flex™ Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)



0,20 inch 0,41 inch 16.240 psi 40.600 psi 3,74 inch 0,146 lbs/ft 0,12 inch 0,14 inch1) 0,51 inch

5,0 mm 10,3 mm 1.120 bar 2.800 bar 95 mm 0,218 kg/m 3,0 mm 3,5 mm1)

10530111 carbon steel

12,9 mm











Type M female swivel 9/16"x18 UNF carbon steel AISI 316Ti

20520601A / 50540601 swivel nut / 50540605

metric female swivel G1/4” carbon steel AISI 316Ti

20520301A / 50540301 swivel nut / 50540305




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6/3 Duralife Flex™ Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyamide (PA) Colour: green, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





























metric female swivel M16x1.5 AISI 316Ti 20620145A / 50620125 ----- Additional fittings are available upon request. ----

Hose Type 3/4 Applications Waterblasting: Ultra High Pressure Waterblast Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





Fittings: ID3, Series B Description Size Material Part Number

HP fitting 1/4”x28UNF LH carbon steel 40340202B

Type M female swivel 9/16”x18UNF carbon steel AISI 316Ti

20340602B / 50540601 swivel nut / 50540605

metric female swivel M12x1.5 carbon steel 20340112B / 50340111



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 4/4 Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





Fittings: ID4, Series B and C Description Size Material Part Number

HP fitting 1/4”x28 UNF LH stainless steel 40460204C



male fitting 1/8”x27 NPTF carbon steel 30440402B

male fitting G1/8” carbon steel 30440302B

BSP female swivel G1/4” carbon steel AISI 316Ti

20440302B / 50540301 swivel nut / 50540305

Type M female swivel 9/16”x18 UNF” stainless steel

AISI 316Ti carbon steel

20460644C swivel nut / 50560605 swivel nut / 50560601



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 5/4 Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels, Hydraulic Tools Oil an Gas: Chemical Injection, Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service

¹)Production related variations up to 5 % are possible *) The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice. ²) BLAST PRO fittings must only be used for tube cleaning operation inside the tube. They are not designed for the use outside of tubes.

© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Inner Core: Polyoxymethylene (POM) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





10540101 carbon steel 10540105

AISI 316Ti 15,0 mm

Fittings: ID5, Series B and Y Description Size Material Part Number

HP fitting 1/4”x28 UNF LH carbon steel 40540211B

HP fitting 1/4”x28 UNF LH AISI 316Ti 40540215B

HP fitting BLAST PRO ²) 1/4”x28 UNF LH stainless steel carbon steel

40540234Y sleeve / 10540232



40540214Y sleeve / 10540232


HP female BLAST PRO ²) 1/4”x28UNF LH stainless steel carbon steel

40540254Y sleeve / 10540232

HP female BLAST PRO ²) 3/8”x24 UNF stainless steel carbon steel

40540244Y sleeve / 10540232


male fitting with 60° cone G1/4” carbon steel 30540301B

male fitting for USIT®-Ring G1/4” carbon steel 30540351B

male fitting special part 100° cone G1/4” carbon steel 30540361B

BSP female swivel G1/4” carbon steel 20540301B / 50540301

BSP female swivel G1/4” AISI 316Ti 20540305B / 50540305

metric female swivel with O-Ring M20x1.5 carbon steel 20540041B / 50860201

Type M female swivel 9/16"x18 UNF carbon steel 20540641B / 50540601

Type M female swivel 9/16"x18 UNF AISI 316Ti 20540645B / 50540605

metric female swivel M14x1.5 carbon steel 20540101B /50540101


Hose Type 6/4 Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels, Instrumentation Packages for Gauges, Rescue Tools Oil and Gas: Chemical Injection, Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyoxymethylene (POM) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




6,3mm 12,6 mm 1.500 bar 3.800 bar 180 mm 0,295 kg/m 3,5 mm

10640101 carbon steel 10640105

AISI 316Ti 16,4 mm




40640214Y sleeve / 10640232


40640234Y sleeve / 10640232




20640301B swivel nut / 50540301 swivel nut /50540305




JIC female swivel 9/16”x18 UNF AISI 316Ti 20640655B / 50540605

¹)Production related variations up to 5 % are possible *) The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice. ²) BLAST PRO fittings must only be used for tube cleaning operation inside the tube. They are not designed for the use outside of tubes. ©

Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200


Hose Type 8/4 Applications Waterblasting: Heat Exchanger Tube Cleaning Hydraulics: Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Chemical Injection, Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyoxymethylene (POM) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





10840102 carbon steel 10840105

AISI 316Ti 20,3 mm



MP fitting BLAST PRO ²) 9/16”x18 UNF LH stainless steel 40840244Y / 10840145 male fitting 1/4”x18 NPTF carbon steel 30840411B



male fitting special part 100° cone G1/4” AISI 316Ti 30840365B





20840231B swivel nut / 51060201 swivel nut / 51060205



Type M female swivel 3/4”x16 UNF carbon steel 20840641B / 50840601

Type M female swivel 3/4”x16 UNF AISI 316Ti 20840645B / 50840605




Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200

8

Hose Type 10/4 Applications Waterblasting: Heat Exchanger Tube Cleaning, Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank and Vessel Cleaning, Waterblast Supply Hose Hydraulics: Controls for Service Equipment, Hydraulic Jacks, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyoxymethylene (POM) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





11040102 carbon steel 11040105 AISI 316 Ti

23,1 mm

Fittings: ID10, Series B,C and Y Description Size Material Part Number

HD fitting 9/16”x18 UNF LH stainless steel 41060204C

MP fitting BLAST PRO ²) 9/16”x18 UNF LH stainless steel carbon steel

41040244Y sleeve / 11040232


BSP female swivel G1/2” stainless steel 21060304C / 51060311

metric female swivel with O-Ring M22x1.5 stainless steel









21040645B swivel nut / 51320615



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/4 Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Hydraulic Jacks, Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





11340122 carbon steel 11340125

AISI 316Ti 27,4 mm

Fittings: ID13, Series C Description Size Material Part Number


MP fitting 3/4”x16 UNF LH stainless steel 41360204C

BSP female swivel G1/2” stainless steel carbon steel

21360314C swivel nut / 51060311




Type M female swivel 1"x12 UNF

stainless steel AISI 316Ti

carbon steel AISI 303

21360644C swivel nut / 51360645 swivel nut / 51360641 swivel nut / 51360643



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/4H Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose, Rotating leaning Device for Waterblast Hydraulics: Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Chemical Injection, Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)









21360314C swivel nut / 51060311










© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 16/4 Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Chemical Injection, Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






MP fitting 3/4”x16 UNF LH AISI 316Ti 41640305B

male fitting 3/4”x14 NPT carbon steel 31640401B

metric female swivel with O-Ring M30x2 carbon steel 21640101B / 51640201

Type M female swivel 1 5/16”x12 UN AISI 316Ti 21640605B / 52040645

JIC female swivel 1 1/16”x12 UN AISI 316Ti 21640645B / 51640605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 20/4 Applications Waterblasting: Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Chemical Injection, Gaseous Media Handling, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





Fittings: ID 20, Series C Description Size Material Part Number

MP fitting 1”x14 UNS LH stainless steel 42060304C

metric female swivel with O-Ring M36x2 carbon steel 22060202C / 52040201

Type M female swivel 1 5/16”x12 UN stainless steel AISI 316Ti

22060644C swivel nut / 52040645


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Hose Type 25/4 Applications Waterblasting: Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Chemical Injection, Nitrogen Service, Gaseous Media Handling Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




24,8 mm 36,3 mm 900 bar 2.250 bar 300 mm 1,715 kg/m 19,0 mm 12540235

AISI 316Ti 45,9 mm

Fittings: ID 25, Series B Description Size Material Part Number

male fitting 1”x11 ½ NPTF AISI 316Ti 32540405B

metric female swivel with O-Ring M42x2 AISI 316Ti carbon steel

22540205B swivel nut / 52520201

Type M female swivel 1 5/16“x12 UN AISI 316Ti 22540645B / 52530645

JIC female swivel 1 5/16“x12 UN AISI 316Ti 22540605B / 52530605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 3/6 Applications Waterblasting: Ultra High Pressure Waterblast Tube Cleaning Hydraulics: Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






HP fitting 1/4”x28UNF LH stainless steel 40360204C

HP fitting 3/8”x24UNF LH stainless steel 40360224C



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 4/6 Applications Hydraulics: Bolt Tensioning & Torque Tools, Hydraulic Jacks, Pressure Testing for Valves, Tooling and Control Panels Waterblasting: Ultra High Pressure Waterjet Table Cutting, Ultra High Pressure Tube Cleaning, Surface Preparation, Paint Removal, Automated Cleaning Booths, Rotating Cleaning Device for Waterblast Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)














© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 5/6 Applications Hydraulics: Bolt Tensioning & Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Waterblasting: Ultra High Pressure Waterjet Table Cutting, Ultra High Pressure Tube Cleaning, Surface Preparation, Paint Removal, Automated Cleaning Booths, Rotating Cleaning Device for Waterblast, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Tank and Vessel Cleaning Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





10560102 carbon steel 10560105

AISI 316Ti 17,5 mm

Fittings: ID5, Series D Description Size Material Part Number

HP fitting 1/4”x28 UNF LH stainless steel 40560294D



HP fitting M14x1.5 LH stainless steel 40560274D

HP-female swivel 9/16”x18 UNF stainless steel

AISI316Ti carbon steel

20560614D swivel nut / 50560605 swivel nut / 50560601


20560314D swivel nut / 50560301

Type M female swivel 9/16"x18 UNF stainless steel



metric female swivel M14x1.5 stainless steel carbon steel

20560164D swivel nut / 50540101



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 8/6 Applications Waterblasting: Ultra High Pressure Waterjet Table Cutting, Surface Preparation, Paint Removal, Tank & Vessel Cleaning, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Automated Cleaning Booths Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)








HP fitting M14x1.5 LH stainless steel 40860104C






AISI 316 Ti carbon steel


Type M female swivel 7/8"x14 UNF stainless steel AISI 316 Ti

20860684C swivel nut / 50860675



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 10/6 Applications Waterblasting: Surface Preparation, Paint Removal, Tank & Vessel Cleaning, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Automated Cleaning Booths, Waterblast Supply Hose, Large Bore Pipe Tube Cleaning Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




9,8 mm 20,4 mm 1.920 bar 4.800 bar 250 mm 1,000 kg/m 5,5 mm 11060102 carbon steel 26,6mm


HD fitting 9/16”x18 UNF LH stainless steel 41060204C

BSP female swivel G1/2” stainless steel 21060304C / 51060311









© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/6 Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Controls for Service Equipment Oil and Gas: Grease Injection, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





11360132 carbon steel 11360135

AISI 316Ti 30,1 mm





21360314C swivel nut / 51060311










© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 16/6 Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Chemical Injection, Gaseous Media Handling, Grease Injection, Hydraulic Control, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






metric female swivel with O-Ring M30x2 stainless steel carbon steel

21660104C swivel nut / 51640201


21660604C swivel nut / 52040645

JIC female swivel 1 5/16”x12 UN stainless steel AISI 316Ti

21660644C swivel nut / 52040605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 20/6 Applications Waterblasting: Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose, Rotating Cleaning Device for Waterblast Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Chemical Injection, Nitrogen Service, Gaseous Media Handling Inner Core: Polyamide (PA) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)









22060644C swivel nut / 52040645


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Hose Type 5/6H Applications Hydraulics: Bolt Tensioning & Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Waterblasting: Ultra High Pressure Waterjet Table Cutting, Ultra High Pressure Tube Cleaning, Surface Preparation, Paint Removal, Automated Cleaning Booths, Rotating Cleaning Device for Waterblast, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Tank and Vessel Cleaning Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)










HP female swivel 9/16”x18 UNF stainless steel




20560314D swivel nut / 50560301





20560164D swivel nut / 50540101



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

,

Hose Type 6/6H MAXIMUS™ Applications Waterblasting: Ultra High Pressure Waterjet Table Cutting, Ultra High Pressure Tube Cleaning, Surface Preparation, Paint Removal, Automated Cleaning Booths, Rotating Cleaning Device for Waterblast, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Tank and Vessel Cleaning Hydraulics: Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)








HP fitting M14x1,5 LH stainless steel 40660124C






© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 8/6H Applications Waterblasting: Ultra High Pressure Waterjet Table Cutting, Surface Preparation, Paint Removal, Tank & Vessel Cleaning, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Automated Cleaning Booths Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)

















20860684C swivel nut / 50860675



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/6H Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Controls for Service Equipment Oil and Gas: Grease Injection, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)









21360314C swivel nut / 51060311










© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 5/6HDC1 Applications Hydraulics: Bolt Tensioning & Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Pressure Testing for Valves, Tooling and Control Panels Waterblasting: Ultra High Pressure Waterjet Table Cutting, Ultra High Pressure Tube Cleaning, Surface Preparation, Paint Removal, Automated Cleaning Booths, Rotating Cleaning Device for Waterblast, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Tank and Vessel Cleaning Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: 1 layer (red) of Polyamide (PA) 2 layer (green) of Polyurethane (PUR) Colour: red / green, other colours upon requestTemperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)














20560314D swivel nut / 50560301





20560164D swivel nut / 50540101



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 8/6HDC1 Applications Waterblasting: Ultra High Pressure Waterjet Table Cutting, Surface Preparation, Paint Removal, Tank & Vessel Cleaning, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Automated Cleaning Booths Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: 1 layer (red) of Polyamide (PA) 2 layer (green) of Polyurethane (PUR) Colour: red / green, other colours upon requestTemperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)

















20860684C swivel nut / 50860675



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 4/8 Applications Hydraulics: Pressure Testing for Valves, Tooling and Control Panels, Instrumentation Packages for Gauges Waterblasting: Ultra High Pressure Waterjet Table Cutting, Ultra High Pressure Tube Cleaning, Paint Removal, Automated Cleaning Booths Inner Core: Polyoxymethylene (POM) Pressure Support: 8 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: purple red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)









Type M female swivel 9/16”x18 UNF stainless steel





© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 8/8 Applications Waterblasting: Ultra High Pressure Waterjet Table Cutting, Surface Preparation, Paint Removal, Tank & Vessel Cleaning, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Automated Cleaning Booths Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 8 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: purple red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)
















Type M female swivel 7/8"x14 UNF stainless steel AISI 316Ti

20860684C swivel nut / 50860675



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6/2KF Applications Automotive: Hot Melt Adhesives / Hot Glue Dispensing, Injection Molding, Chemical Transfer / Paint Transfer, Robotic Systems, Compressed Gas

Inner Core: PTFE Pressure Support: 2 layers of high-tensile steel wire Outer Cover: 1 layer of braided steel wire Temperature: -94°F to 392°F [-70°C to +200°C] ¹)

∅ ID ∅ OD Working Pressure ¹)²)

Burst Pressure ²)4)

Min. Bend Radius ³) Weight Nipple

∅ ID Sleeve

0,24 inch 0,44 inch 7.250 psi 29.000 psi 2,36 inch 0,176 lbs/ft 0,18 inch

6,2 mm 11,2 mm 500 bar 2.000 bar 60 mm 0,262 kg/m 4,5 mm T00.06.02.00

carbon steel

Fittings: ID6, Series F

Description Size Material Part Number

BSP female swivel G1/4” carbon steel carbon steel

nipple / T01.06.08.00 swivel nut / T08.06.00

1) If used as a steam hose the max. working pressure is 203 psi (14bar) and the max. temperature is +482°F (+250°C)

2) The burst and working pressure applies to working temperatures from +20°C to +50°C. Temperature correction factors: (20°C/1,0), (100°C/0,95), (150°C 0,90), (200°C/0,83).

3) With dynamic stress, the bend radius should at least be doubled. The radius should be adjusted to the conditions.

Important Information! KF hoses are intended for being used as basic hoses for heating hose systems. They do not have an outer cover, and the wires are not protected against corrosion. It is not allowed to use these hoses in a “normal” hose assembly without taking the right steps to prevent the corrosion of the wires because there exists the risk of injury as well as the possibility of the failure of the hose assembly. KF hoses are available as a special execution with a plastic outer cover. For further information, please contact our SPIR STAR sales personnel.

Wichtiger Hinweis KF-Schläuche sind zur Verwendung als Grundschlauch für Heizschlauchsysteme vorgesehen. Sie besitzen keine Oberdecke und die Drähte sind nicht korrosionsgeschützt. Die Verwendung als lose Schlauchleitung ohne entsprechende Maßnahmen, die eine Korrosion der Drähte ausschließen, ist auch im Hinblick auf etwaige Verletzungsrisiken nicht zulässig und kann zum Ausfall der Schlauchleitung führen. KF-Schläuche sind als Sonderausführung mit Kunststoffoberdecke erhältlich. Für weitere Informationen kontaktieren Sie bitte einen SPIR STAR Verkaufsmitarbeiter


4)Production related variations up to 5 % are possible *) The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice.

© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008






∅ ID Sleeve



carbon steel




nipple / T01.08.10.00 swivel nut / T08.08.09.00








© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008






∅ ID Sleeve



carbon steel












© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/2KF Applications Automotive: Hot Melt Adhesives / Hot Glue Dispensing, Injection Molding, Chemical Transfer / Paint Transfer, Robotic Systems, Compressed Gas Inner Core: PTFE Pressure Support: 2 layers of high-tensile steel wire Outer Cover: 1 layer of braided steel wire Temperature: -94°F to 392°F [-70°C to +200°C] ¹)




∅ ID Sleeve



carbon steel





1) If used as a steam hose the max. working pressure is 203 psi (14bar) and the max. temperature is +482°F (+250°C) 2) The burst and working pressure applies to working temperatures from +20°C to +50°C. Temperature correction factors: (20°C/1,0), (100°C/0,95), (150°C 0,90), (200°C/0,83). 3) With dynamic stress, the bend radius should at least be doubled. The radius should be adjusted to the conditions. Important Information! KF hoses are intended for being used as basic hoses for heating hose systems. They do not have an outer cover, and the wires are not protected against corrosion. It is not allowed to use these hoses in a “normal” hose assembly without taking the right steps to prevent the corrosion of the wires because there exists the risk of injury as well as the possibility of the failure of the hose assembly. KF hoses are available as a special execution with a plastic outer cover. For further information, please contact our SPIR STAR sales personnel.




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008





∅ ID Sleeve



carbon steel









© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008





∅ ID Sleeve



carbon steel



metric female swivel M36x2 carbon steel carbon steel

nipple / T03.20.25.00-3 swivel nut / T03.36.00





© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 25/2KF Applications Automotive: Hot Melt Adhesives / Hot Glue Dispensing, Injection Molding, Chemical Transfer / Paint Transfer, Robotic Systems, Compressed Gas Inner Core: PTFE Pressure Support: 2 layers of high-tensile steel wire Outer Cover: 1 layer of braided steel wire

Temperature: -94°F to 392°F [-70°C to +200°C] ¹)




∅ ID Sleeve



carbon steel



metric female swivel M42x2 carbon steel carbon steel

nipple / T03.25.30.00-3 swivel nut / T03.42.00





© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

*) Safety factor between burst pressure and working pressure as well as test pressure depends on operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice.

© Copyright by SPIR STAR™ | revised on 15.08.2007

HT-Series

PVDF Inner core and Outer cover – unique within the realms of thermoplastic hose

The HT Series was developed especially for the exacting demands of the HP/HT (high-pressure/high temperature) applications. Both the inner core and the outer cover of these hose types are made of PVDF, a material that is the world-wide standard in terms of heat and chemical resistance.

In order to achieve the necessary working pressures up to 6 layers of high-tensile spring-steel wire are spiralized as a pressure support.

Because of this unique combination of materials our products are especially suited for applications involving methanol service, for dealing with aggressive chemicals and in all cases where an extremely low permeation rate is needed.

All hose types of this Series are heat-resisting up to 150°C (300°F) and available for working pressures up to 1.125 bar with a safety factor of 1:4 (burst pressure: 4.500 bar).

Upon request the hoses can be supplied in long lengths (for example 6/4HT - 4500 m) as they are needed for Offshore Umbilicals.

Important Information!

In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from

escaping fluids at high temperature ( up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR

HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury.

The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled

to ambient temperature.

Hose Type 5/4HT High Temperature to 300°F (+150°C) Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Methanol Injection, Nitrogen Service Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: PVDF Colour: grey, other colours upon request Temperature: -4°F to 300°F [-20°C to +150°C]


Burst Pressure ¹)




5,0 mm 11,2 mm 1.285 bar 4.500 bar 250 mm 0,280 kg/m 2,5 mm 10540145

AISI 316Ti 15,4 mm

Fittings: ID5, Series H Description Size Material Part Number

BSP female swivel G1/4” AISI 316Ti 20540315H / 50540305

Type M female swivel 9/16”x18 UNF AIS I316Ti 20540665H / 50540605

Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature ( up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6/2WHT High Temperature to 300°F (+150°C) Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Methanol Injection, Nitrogen Service Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: PVDF Colour: grey, other colours upon request Temperature: -4°F to 300°F [-20°C to +150°C]


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Burst Pressure ¹)




6,3 mm 12,2 mm 915 bar 3.200 bar 150 mm 0,266 kg/m 4,0 mm


10630195W AISI 316Ti

15,4 mm



























Hose Type 6/4HT High Temperature to 300°F (+150°C) Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Methanol Injection, Nitrogen Service


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: PVDF Colour: grey, other colours upon request Temperature: -4°F to 300°F [-20°C to +150°C]


Burst Pressure ¹)





10640101 carbon steel 10640105

AISI 316Ti 16,4 mm




40640214Y sleeve / 10640232


40640234Y sleeve / 10640232



BSP female swivel G1/4” carbon steel carbon steel AISI 316 Ti








Hose Type 8/2WHT High Temperature to 300°F (+150°C) Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Methanol Injection, Nitrogen Service Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: PVDF Colour: grey, other colours upon request Temperature: -4°F to 300°F [-20°C to +150°C]


Burst Pressure ¹)





AISI 316Ti 20,7 mm


Type M female swivel 3/4”x16 UNF AISI 316Ti 20820665H / 50840605

JIC female swivel 3/4”x16 UNF AISI 316Ti 20820605H / 50840605




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008



Burst Pressure ¹)






20,2 mm

Fittings: ID8, Series HB Description Size Material Part Number

BSP female swivel G3/8” carbon steel 20840311HB / 50860301

Type M female swivel 3/4”x16 UNF AISI 316Ti 20840645HB / 50840605

JIC female swivel 3/4”x16 UNF AISI 316Ti 20840605HB / 50840605




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008



Burst Pressure ¹)




9,9 mm 18,4 mm 1.085 bar 3.800 bar 300 mm 0,695 kg/m 5,0 mm 11040145

AISI 316Ti 25,1 mm


metric female swivel with O-Ring M22x1.5 AISI316Ti AISI316Ti

carbon steel

21040115H swivel nut / 51060205 swivel nut / 51060201


21040645H swivel nut / 51320615

JIC female swivel 3/4”x16 UNF AISI316Ti 21040605H / 51320615

JIC female swivel 9/16”x18 UNF AISI316Ti 21040615H / 51040615 Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature ( up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/4HHT High Temperature to 300°F (+150°C) Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Methanol Injection, Nitrogen Service Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: PVDF Colour: grey, other colours upon request Temperature: -4°F to 300°F [-20°C to +150°C]


Burst Pressure ¹)



0,50 inch 0,87 inch 15.080 psi 52.490 psi 11,81 inch 0,672lbs/ft 0,30 inch 1,16 inch


Fittings: ID13, Series C




BSP female swivel G1/2” stainless steel


21360314 swivel nut / 51060315 swivel nut / 51060311











© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6/2LTKE Applications Oil and Gas: Sub Sea Well Control, Hydraulic Control Inner Core: Polyamide (PA) Pressure Support: 2 layers of aramide 1 braided layer of AISI316Ti Outer Cover: Polyamide (PA) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





AISI 316Ti 15,9 mm

Fittings: ID6, Series L Description Size Material Part Number

JIC female swivel 7/16”x20 UNF AISI 316Ti 20630675L / 50620605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6/4LTKE Applications Oil and Gas: Sub Sea Well Control, Hydraulic Control Inner Core: Polyamide (PA) Pressure Support: 4 layers of aramide 1 braided layer of AISI316Ti Outer Cover: Polyamide (PA) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





AISI 316Ti 17,5 mm

Fittings: ID6, Series L Description Size Material Part Number

JIC female swivel 7/16”x20 UNF AISI 316Ti 20630675L / 50620605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008



M-Series

BESNO P40 TL0: a tried and tested material – many years of experience The M-Series stands for hose types with an inner core made of methanol-washed PA11 BESNO P40 TLO (Nylon 11), a material that has been tried and tested in the Offshore Industry for years. Up to 4 layers of high-tensile spring-steel wire serve as a pressure support. The outer cover is made of polyamide. Through the combination of these materials this hose series attains high flexibility, low weight and a low permeation rate as it is needed with applications involving methanol-service. The hoses are suited for applications up to 60°C (140°F) and working pressures up to 690 bar with a safety factor of 1:4 (burst pressure appx. 2700 bar). Furthermore, all hoses of this series meet the hygiene requirements of the NACE Standards.

Important Information!

Additionally to that, all hose types of this series correspond to the hygienic regulations of the NACE standard.

Hose Type 6/2WM Applications Oil and Gas: Chemical Injection, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control Inner Core: BESNO P40 TLO (PA11) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: dark blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






10630185W AISI 316Ti

16,8 mm

Fittings: ID6, Series M Description Size Material Part Number

male fitting 1/4”x18 NPT carbon steel 30620401M


20620645M swivel nut / 50540605

JIC female swivel 7/16”x20 UNF AISI 316Ti AISI 316Ti

carbon steel

20620605M swivel nut / 50620605 swivel nut / 50620601

JIC female swivel 9/16”x18 UNF AISI 316Ti AISI 316Ti

carbon steel

20620625M swivel nut / 50540605 swivel nut / 50540601



Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 0

6.08

.200

8



Burst Pressure ¹)






10830185W AISI 316Ti

18,3 mm



Type M female swivel 3/4”x16 UNF AISI 316 Ti 20820645M / 50840605

JIC female swivel 9/16”x18 UNF AISI 316Ti 20820655M / 51030695



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008



Burst Pressure ¹)





AISI 316Ti 21,5 mm


Type M female swivel 3/4”x16 UNF AISI 316Ti 21020645M / 51320615




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008



Burst Pressure ¹)






11330185W AISI 316Ti

27,8 mm



Type M female swivel 1”x12 UNF AISI 316Ti 21320645M / 51360645




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 25/2KM Applications Oil and Gas: Chemical Injection, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control Inner Core: BESNO P40 TLO (PA11) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyamide (PA) Colour: dark blue, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





AISI 316Ti 42,0 mm

Fittings: ID25, Series S Description Size Material Part Number

Type M female swivel 1 5/16”x12 UN AISI 316Ti 22530645S / 52530645

JIC female swivel 1 5/16”x12 UN AISI 316Ti 22530605S / 52530605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008



PPA-Series

A combination of PVDF and PA of high quality The Alternative to the HT-Series. The PPA-Series combines the advantages of the chemical-resisting PVDF as inner core material and Polyamide, which has been tried and tested for years, as material of the outer cover. The permeation rate with methanol applications is as low as with our HT-Series. All hoses are suited for applications up to 80°C (176°F) and working pressures up to 950 bar with a safety factor of 1:4 (burst pressure: 3800 bar). Upon request the hoses can be supplied in long lengths (for example 6/4PPA -4500m) as they are needed for Offshore Umbilicals.

Hose Type 5/4PPA Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

15.

10.2

008

Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: dark green, other colours upon requestTemperature: -4°F to 176°F [-20°C to +80°C]


Burst Pressure ¹)



0,20 inch 0,44 inch 18.630 psi 65.250 psi 9.84 inch 0.172 lbs/ft 0,10 inch 0,59 inch

5,0 mm 11,2 mm 1.285 bar 4.500 bar 250 mm 0.256 kg/m 2,5 mm

10540101 carbon steel 10540105

AISI 316Ti 15,0 mm


HP fitting 1/4”x28 UNF LH carbon steel 40540211B


HP fitting BLAST PRO 1/4”x28 UNF LH stainless steel carbon steel

40540234Y sleeve / 10540232


HP fitting BLAST PRO 3/8”x24 UNF LH stainless steel carbon steel

40540214Y sleeve / 10540232


HP female BLAST PRO 1/4”x28 UNF LH stainless steel carbon steel

40540254Y sleeve / 10540232

HP female BLAST PRO 3/8”x24 UNF stainless steel carbon steel

40540244Y sleeve / 10540232



male fitting for USIT®-Ring G1/4” carbon steel 30540351B

male fitting special part 100° cone G1/4” carbon steel 30540361B






metric female swivel M14x1.5 carbon steel 20540101B / 50540101


Hose Type 6/2WPPA Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: dark green, other colours upon requestTemperature: -4°F to 176°F [-20°C to +80°C]


Burst Pressure ¹)




6,3 mm 12,2 mm 915 bar 3.200 bar 150 mm 0,266 kg/m 4,0 mm


10630195W AISI 316Ti

15,4 mm


























Hose Type 6/4PPA Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: dark green, other colours upon requestTemperature: -4°F to 176°F [-20°C to +80°C]


Burst Pressure ¹)





10640101 carbon steel 10640105

AISI 316Ti 16,4 mm




40640214Y sleeve / 10640232


40640234Y sleeve / 10640232



BSP female swivel G1/4” carbon steel carbon steel AISI 316 Ti








Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200

8



Burst Pressure ¹)



















carbon steel




20820605A swivel nut / 50820601



Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200

8

Hose Type 8/4PPA Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: dark green, other colours upon request Temperature: -4°F to 176°F [-20°C to +80°C]


Burst Pressure ¹)





10840102 carbon steel 10840105

AISI 316Ti 20,3 mm



MP fitting BLAST PRO ²) 9/16”x18 UNF LH stainless steel AISI 316Ti

40840244Y sleeve / 10840145




male fitting special part 100° cone G1/4” AISI 316 Ti 30840365B













Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200

8



Burst Pressure ¹)






23,1 mm

Fittings: ID10, Series B,C and Y Description Size Material Part Number


MP fitting BLAST PRO ²) 9/16”x18 UNF LH stainless steel carbon steel

41040244Y sleeve / 11040232








metric female swivel with O-Ring M24x1.5 stainless steel AISI 316Ti

21060224C swivel nut / 51360205



21040645B swivel nut / 51320615



Cop

yrig

ht b

y SP

IR S

TAR

™ |

revi

sed

on 1

8.06

.200

8

Hose Type 13/4HPPA Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: dark green, other colours upon requestTemperature: -4°F to 176°F [-20°C to +80°C]


Burst Pressure ¹)




















© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008



Burst Pressure ¹)









22060644C swivel nut / 52040645



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 25/4PPA Applications Oil and Gas: Chemical Injection, Gaseous Media Handling, Hydraulic Control, Methanol Injection, Nitrogen Service, Sub Sea Well Control Inner Core: PVDF Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: dark green, other colours upon request Temperature: -4°F to 176°F [-20°C to +80°C]


Burst Pressure ¹)





AISI 316Ti 45,9 mm

Fittings: ID 25, Series B Description Size Material Part Number

male fitting 1”x11 ½ NPTF AISI 316Ti 32540405B

metric female swivel with O-Ring M42x2 AISI 316Ti carbon steel

22540205B swivel nut / 52520201

Type M female swivel 1 5/16“x12 UN AISI 316Ti 22540645B / 52530645

JIC female swivel 1 5/16“x12 UN AISI 316Ti 22540605B / 52530605



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 8/2WR Heavy duty outer cover for rough service Applications Waterblasting: Rotating Cleaning Device for Waterblast, Large Bore Pipe Tube Cleaning, Tank and Vessel Cleaning, Waterblast Supply Hose Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Grease Injection, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: grey, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




8,0 mm 16,0 mm 1.040 bar 2.600 bar 110 mm 0,364 kg/m 4,5 mm 10830201WR







male fitting special part 100° cone G1/4” AISI 316Ti 30840365B












© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Hose Type 8/6HR Applications Waterblasting: Waterjet Cutting, Surface Preparation, Paint Removal, Tank & Vessel Cleaning, Hydro Demolition of Concrete, Robotic Cleaning, Animated Cleaning Booths, Waterblast Supply Hose Inner Core: Polyoxymethylene (POM) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)

















20860684C swivel nut / 50860675



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/2KR Heavy duty outer cover for rough service Applications Waterblasting: Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Grease Injection Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyurethane (PUR) Colour: black, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)




12,8mm 22,3 mm 800 bar 2.000 bar 150 mm 0,690 kg/m 7,5 mm

11330201WRcarbon steel

11330205WRAISI 316Ti

27,5 mm

Fittings: ID13, Series O and C Description Size Material Part Number



male fitting 1/2”x14 NPTF carbon steel 31360401O

male fitting 1/2”x14 NPTF AISI 316Ti 31360405O

BSP female swivel G1/2” carbon steel 21360332O / 51060311




metric female swivel with O-Ring M22x1.5 carbon steel 21360122O / 51360221





Type M female swivel 1"x12 UNF carbon steel 21360642O / 51360641



AISi303 carbon steel




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/2WR Silver Mongoose Heavy duty outer cover for rough service Applications Waterblasting: Tank & Vessel Cleaning, Large Bore Pipe Tube Cleaning, Rotating Cleaning Device for Waterblast, Waterblast Supply Hose Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Grease Injection, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: silver, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)





11330201WRcarbon steel

11330205WRAISI 316Ti

27,5 mm

Fittings: ID13, Series O and C Description Size Material Part Number



male fitting 1/2”x14 NPTF carbon steel 31360401O

male fitting 1/2”x14 NPTF AISI 316Ti 31360405O

BSP female swivel G1/2” carbon steel 21360332O / 51060311






metric female swivel with O-Ring M24x1.5 stainless steel AISI 316Ti

21360244C swivel nut / 51360205

Type M female swivel 1"x12 UNF carbon steel 21360642O / 51360641

Type M female swivel 1"x12 UNF stainless steel

AISI 316Ti AISI 303




© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13/6HR Heavy duty outer cover for rough service Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Nitrogen Service Inner Core: Polyamide (PA) Pressure Support: 6 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Colour: red, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)









21360314C swivel nut / 51060311









© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


Hose Type 5mmUHP Applications Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Waterblasting: Ultra High Pressure Waterjet Table Cutting, Surface Preparation, Paint Removal, Automated Cleaning Booths, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Tank and Vessel Cleaning Inner Core: Polyoxymethylene (POM) Pressure Support: 8 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: yellow, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)














20560314D swivel nut / 50560301





20560164D swivel nut / 50540101



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008


© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6mmUHP MAXIMUS™ Applications Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Waterblasting: Ultra High Pressure Waterjet Table Cutting, Surface Preparation, Paint Removal, Automated Cleaning Booths, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Tank and Vessel Cleaning Inner Core: Polyoxymethylene (POM) Pressure Support: 8 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: yellow, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)






HP fitting 3/8”x24 UNF LH stainless steel 40660204C HP fitting 9/16”x18 UNF LH stainless steel 40660224C

HP fitting M14x1,5 LH stainless steel 40660124C





Hose Type 8mmUHP Applications Waterblasting: Ultra High Pressure Waterjet Table Cutting, Surface Preparation, Paint Removal, Tank & Vessel Cleaning, Hydro Demolition of Concrete, Robotic Surface Cleaning of Ships, Automated Cleaning Booths Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Inner Core: Polyoxymethylene (POM) Pressure Support: 8 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: yellow, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)
















Type M female swivel 7/8"x14 UNF stainless steel AISI 316Ti

20860684C swivel nut / 50860675



© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 13mmUHP Applications Waterblasting: Hydro Demolition of Concrete, Large Bore Pipe Tube Cleaning, Tank & Vessel Cleaning, Waterblast Supply Hose Hydraulics: Pressure Testing for Valves, Tooling and Control Panels Oil and Gas: Gaseous Media Handling, Nitrogen Service Inner Core: Polyoxymethylene (POM) Pressure Support: 8 layers of high-tensile steel wire Outer Cover: Polyamide (PA) Colour: yellow, other colours upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Burst Pressure ¹)









21360314C swivel nut / 51060311










© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

18.

06.2

008

Hose Type 6/2WL Twin Hose Applications Hydraulics: Bolt Tensioning and Torque Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing for Valves, Tooling and Control Panels, Hydraulic Tools

*) The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice.

© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

05.

11.2

007

Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Color: black and blue, other colors upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Min. Burst Pressure



0.23 inch 0.47 inch 17,400 psi 43,500 psi 3.15 inch 0.319 lbs/ft 0.16 inch 0.61 inch

5.9 mm 12.0 mm 1,200 bar 3,000 bar 80 mm 0.474 kg/m 4.0 mm


1630195W AISI 316Ti

15.5 mm


























Hose Type 8/2W Twin Hose Applications Hydraulics: Bolt Tensioning Tools, Hydraulic Jacks, Controls for Service Equipment, Instrumentation Packages for Gauges, Pressure Testing, Tooling and Control Panels Inner Core: Polyamide (PA) Pressure Support: 4 layers of high-tensile steel wire Outer Cover: Polyurethane (PUR) Color: black and blue, other colors upon request Temperature: -22°F to 140°F [-30°C to +60°C]


Min. Burst Pressure



0.31 inch 0.56 inch 15,080 psi 37,700 psi 4.33 inch 0.442 lbs/ft 0.22 inch 0.72 inch

8.0 mm 14.3 mm 1,040 bar 2,600 bar 110 mm 0.628 kg/m 5.5 mm 10830191W

carbon steel 18.3 mm













carbon steel



JIC female swivel 9/16”x18 UNF AISI 316 Ti 20820605A / 50820605

*) The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media a safety factor of 1:6 is to be applied and the outer cover is to be pricked. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly can be less. We reserve our rights for changes without notice.

© C

opyr

ight

by

SPIR

STA

R™

| re

vise

d on

05.

12.2

007



ACCESSORIESSpring Guards

Burst Guards

Abrasion Cover

Spring guards, which are available for most hoses,reduce stress near the hose end fitting and preventkinking of the hose. In addition, they can becustom fit to the length of the hose. Spring guardsare made of high tensile spring steel with a rustresistant coating

Burst guards protect the operator and surroundingequipment from hose failure. Burst guards aremade of synthetic rubber with wire steelreinforcement.

Abrasion covers help protect the hose fromexcessive wear due to use on rough surfaces.Abrasion covers are made of clear vinyl andreinforced with a rigid PVC helix coil.


ACCESSORIES

Containment Grips

Support Grips

Whip Checks

Bend Restrictors

Containment grips limit the possibilityof serious injury to personnel in the eventof a connection failure. Containment gripsare available in stainless steel or galvanizeplated carbon steel

Support grips assist in holding the weight of thehose as it hangs in vertical or slanted positions.Support grips are made of high grade, coated,galvanized wire.

Whip checks limit the hose from whipping inthe event of a connection failure. Whipchecks are made of durable nylon strappingwith extra heavy stitching.

Bend restrictors, which are available for mosthoses, assist in reducing the stress near the endfitting as well as prevent kinking of the hose.Bend restrictors are made of PVC material.


Tightening Connection Thread Sizes Torque (ft. Lb.) High Pressure

1/4" 9/16 - 18 253/8" 3/4" - 16 509/16" 1-1/18" - 12 75

Medium Pressure1/4" 7/16" - 20 203/8" 9/16" - 18 309/16" 13/16" - 16 853/4" 3/4" NPSM 901" 1-3/8" - 12 125

Type M SwivelM9 9/16" - 18 25-30M12 3/4" - 16 40-50M14 7/8" - 14 50-60M16 1" - 12 75-85M21 1-5/16" - 12 100-120

Leakage at Swivel Nut-to-Adapter Joint(Observed by leak at weep hole in swivel nut)1. Reduce system pressure to zero.2. Unscrew swivel nut and check cone surfaces of

hose insert and adaptor.3. If hose insert is damaged, return hose to SPIR

STAR for repair and retest.4. If cone surfaces look good after inspection and

cleaning, retighten swivel nut. Do not exceed150% of recommended torque.

Leakage at Type M Adapter-to-Port(Observed by leak at weep hole in pressure port orleak at threads for NPT Adaptors.)1. Reduce system pressure to zero.2. Loosen hose swivel nut.3. Tighten adapter into port.4. Re-tighten swivel nut.

Never use the Type M swivel nut to tightenthe adapter into the port.

Hose Swivel Nut

Hose InsertSealing Surface

Weep Hole

Adaptor SealingSurface

Adaptor

Equipment Port

Recom

mended Tightening Procedures

HOSE DATA


HOSE DATA

�� PA � polyamide �� = resistant�� PUR �� polyurethane �� = not resistant� �� FEP �� fluorinated ethylene propylene �� = not checked�� POM �� polyoxymethylene

acetate solvents �� - dibutyl phthalate �� - dibutyl sebacate �� - dihexyl phthalate �� - dioctyl phthalate �� 1-butanone �� accumulator acid �� acetic acid �� acetic anhydride �� acetone �� acetylene �� acidity of wine �� alumen �� aluminium chloride �� aluminium fluoride �� aluminium sulphate �� ammonia (concentrate) �� ammonia gas �� ammonium chloride �� ammonium hydroxide �� ammonium nitrate �� ammonium phosphate �� ammonium sulphate �� amyl acetate �� amyl alcohol �� aniline dyes �� antifreezing compound �� apple juice �� apple purée �� aqua regi(nitrohydrochloric acid) �� argon �� asphalt �� ASTM fuel B ��

Medium

�� 68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F

20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance

ASTM fuel B + 20% ethanol �� barium chloride �� barium hydroxide ��


HOSE DATAMedium

barium hydroxide �� barium sulphite �� beer �� benzaldehyde �� benzene �� benzoic acid �� bone oil �� borax �� boric acid �� brake fluid �� brandy �� brine �� bromine, liquid �� butane �� butanol �� butter �� buttermilk �� butyl acetate �� butyl acetate �� butyl alcohol �� cabinet polish �� calcium chloride �� calcium hydrochloride �� calcium hydroxide �� calcium nitrate �� carbon dioxide �� carbon disulphide �� carbon monoxide �� carbon tetrachloride �� caustic potash solution �� chloracetone �� chloric gas �� chlorine, liquid �� chloroacetic acid �� chlorobenzene �� chlorofluorocarbons ��

�� 68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F

20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance

chloroform �� chlorosulphonic acid �� chrome baths ��


Medium

chromic acid �� citric acid �� cloves oil �� Coca Cola �� coconut oil �� coffee �� copper chloride �� copper sulphate �� cresol �� cresol solution �� crude oil �� crude petroleum �� cyclohexane �� cyclohexanol �� cyclohexanone �� decahydronaphthalene �� de-ionized water �� demineralized water �� dibutyl phthalate �� diesel oil �� diethyl ether �� -diisononyl phthalate �� dimethyl formamide �� dish washing compound �� Dixan (caustic solution) �� DOP (PVC plasticizer) �� edible oil, animal �� edible oil, vegetable �� egg (raw, boiled) �� ether �� ethyl acetate �� ethyl alcohol �� ethyl dichloride �� ethylene glycol ��

HOSE DATA

ferric chloride �� ferrous chloride �� fir leaf oil ��

�� 68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F

20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance

fish, sour �� fixing salt �� floor wax �� Fluorsilicon acid �� food stuffs (gen. suitable) ��


HOSE DATA

formaldehyde �� formalin �� formic acid �� fruit jelly �� fruit juices �� gas oil �� gasoline �� gin �� Girling �� glucose �� glycerin �� glycol �� grapefruit juice �� groundnut oil �� heating oil �� heptane �� hexane �� honey �� hydrochloric acid �� hydrofluoric acid �� hydrogen �� hydrogen peroxide 10% �� hydrogen sulphide, H2S low percentage �� ink �� iron salt solutions �� iron sulphate �� isoamyl alcohol �� isooctane �� isocyanat �� isopropanol �� Javel water 16 % �� lactic acid �� Landolin �� lemonades �� linseed oil ��

Medium

�� 68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F

20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance


HOSE DATAMedium

liqueurs �� LITEX �� LOCKHEED �� lubricating greases �� lubricating oils �� LYSOL �� magnesium chloride �� magnesium hydroxide �� magnesium sulphate �� maize oil �� margarin �� mercury �� methanol �� methyl alcohol �� methyl ethyl ketone �� methyl isopropyl ketone �� methylene chloride �� milk �� mineral oils �� motor oils (motor vehicles) �� Naphtha �� Natriumhypochlorid �� natural gas �� nickel chloride �� nickel sulphate �� nictric acid �� nitrobenzene �� nitrogen �� OCEANIC HW 443 �� octane �� oils, etherial �� oleic acid �� oleum (fuming sulfuric acid) �� orange juice �� orange peel �� oxalic acid �� oxygen �� ozone �� palm kernel oil �� paraffin ��

�� 68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F

20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance

Mediumparaffin oil �� pektine �� pepper �� peppermint oil �� perchloroethylen �� perfume �� peroxide fluid �� petroleum ether �� phenol �� phosphoric acid �� phosphorous pentoxide �� pine leaf oil �� plasticizer �� Polyfluorcarbon �� potassium carbonate �� potassium chlorate ��


HOSE DATA

potassium chloride �� potassium dichromate �� potassium iodide �� potassium nitrate �� potassium permanganate �� potassium sulphate �� propane, gaseous �� propane, liquid �� Pydraul �� pyridine �� Quecksilberchlorid �� rum �� rum aroma �� sagrotan �� salt, dry �� seawater �� semolina �� shampoo �� shoe polish �� silicone oils �� silver salts �� SKYDROL HT �� soap solution �� soda (sodium carbonate) ��

Medium��

68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F 20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance

soda water �� sodium bicarbonate ��

HOSE DATA


Medium

sodium bisulphate �� sodium carbonate �� sodium chloride �� sodium chlorite solution (5%) �� sodium cyanide �� sodium hydroxide �� sodium nitrate �� sodium perborate �� sodium phosphates �� sodium silicate �� sodium sulfide �� sodium thiosulphate �� soft soap �� solvent naphtha (white spirit) �� soy bean oil �� starch �� stearic acid �� succinic acid �� sulphur �� sulphur chloride �� sulphur trioxide �� sulphuric acid �� sweet orange oil �� tar �� tea �� tea leaves �� terpentin oil �� tetrahydrofurane �� tetrahydronaphthalene �� thiophen �� toluene �� transformer oil �� trichlorethylene �� typewriter oil �� urea �� varnish �� vaseline ��

�� 68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F

20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance

vegetable �� vinegar �� vinegar concentrate �� water �� whisky �� wine �� xylene �� zinc chloride �� zinc sulphate �� zinn chlorid ��

HOSE DATA


Medium

�� 68°F 140°F 68°F 140°F 68°F 140°F 68°F 140°F

20°C 60°C 20°C 60° C 20°C 60°C 20°C 60°C

Chem

ical Resistance

© C

opyr

ight

by

SP

IR S

TAR

™11

.08.

2008

Res

ista

nce

agai

nst E

xter

nal P

ress

ure

(Col

laps

e Pr

essu

re T

est)

ID 5

mm

- ID

10m

m

pres

sure

[bar

]; 69

0pr

essu

re [b

ar];

525

pres

sure

[bar

]; 35

0pr

essu

re [b

ar];

600

pres

sure

[bar

]; 17

5pr

essu

re [b

ar];

150

pres

sure

[bar

]; 20

0pr

essu

re [b

ar];

175

pres

sure

[bar

]; 20

0pr

essu

re [b

ar];

300

pres

sure

[bar

]; 50

0pr

essu

re [b

ar];

400

pres

sure

[bar

]; 57

5pr

essu

re [b

ar];

50pr

essu

re [b

ar];

250

pres

sure

[bar

]; 45

0pr

essu

re [b

ar];

600

pres

sure

[bar

]; 12

5pr

essu

re [b

ar];

150pr

essu

re [b

ar];

225

pres

sure

[bar

]; 32

5pr

essu

re [b

ar];

275

pres

sure

[bar

]; 30

0pr

essu

re [b

ar];

325

pres

sure

[bar

]; 60

0pr

essu

re [b

ar];

100

pres

sure

[bar

]; 15

0pr

essu

re [b

ar];

150

pres

sure

[bar

]; 37

5pr

essu

re [b

ar];

250

pres

sure

[bar

]; 31

0

010

020

030

040

050

060

070

080

0

5/4

5/4H

T5/

4PP

A5/

6H6/2

6/2L

TKE

6/2W

6/2W

L6/

2WM

6/2W

HT

6/2W

PP

A6/

46/

4HT

6/4L

TKE

6/4M

rein

forc

ed6/

4PP

A6m

m U

HP

8/2

8/2W

8/2W

HT

8/4

8/4H

T8/

4PP

A8/

68/

6H10

/210

/2W

10/2

WM

10/4

10/4

HT

10/6

hose

type

pres

sure

[bar

]

© C

opyr

ight

by

SP

IR S

TAR

™11

.08.

2008

Res

ista

nce

agai

nst E

xter

nal P

ress

ure

(Col

laps

e Pr

essu

re T

est)

ID 1

3mm

- ID

25m

m

pres

sure

[bar

]; 75

pres

sure

[bar

]; 12

5

pres

sure

[bar

]; 12

5

pres

sure

[bar

]; 10

0

pres

sure

[bar

]; 15

0

pres

sure

[bar

]; 22

5pres

sure

[bar

]; 25

0

pres

sure

[bar

]; 25

0

pres

sure

[bar

]; 15

0

pres

sure

[bar

]; 15

0

pres

sure

[bar

]; 50

pres

sure

[bar

]; 45

pres

sure

[bar

]; 50

pres

sure

[bar

]; 50

pres

sure

[bar

]; 12

5pres

sure

[bar

]; 15

0

pres

sure

[bar

]; 40

pres

sure

[bar

]; 27

5

pres

sure

[bar

]; 50

pres

sure

[bar

]; 50

050

100

150

200

250

300

13/2

13/2

W13

/2W

R13

/2W

M13

/413

/4H

13/4

HP

PA

13/4

HH

T13

/616

/420

/220

/2K

20/4

20/4

PP

A20

/620

/6P

PA

25/2

K25

/2K

MH

CR

25/4

25/4

PP

A

hose

type

pres

sure

[bar

]


The sale of SPIR STAR, Ltd. (“SPIR STAR”) products is governed by the following terms and conditions (“Terms”). All references to“Customer” mean the customer (including its subsidiaries and affiliates) whose name appears on SPIR STAR’s credit application,sales order or invoice.

1. Terms and Conditions of Sale: All descriptions, quotations, proposals, offers, acknowledgments, acceptances and sales of SPIRSTAR’s products are subject to and shall be governed exclusively by these Terms, which shall constitute a contract betweenCustomer and SPIR STAR. Any terms or conditions proposed by Customer that are in addition to, or inconsistent with those statedherein, are hereby rejected. No such additional different or inconsistent terms and conditions shall become part of the salebetween Customer and SPIR STAR unless expressly accepted in advance, in writing, by an officer of SPIR STAR. SPIR STAR’sacceptance of any offer to purchase by Customer is expressly conditioned upon Customer’s assent to all the Terms stated herein.Acceptance of SPIR STAR’s products by Customer shall, in any event, constitute assent to the Terms.

2. Payment: Payment shall be made by Customer net 30 days from the date of delivery of the products. Any claims by Customer foromissions or shortages in a shipment shall be deemed to be waived unless SPIR STAR receives notice thereof within 30 days afterCustomer’s receipt of the shipment.

3. Delivery: Unless otherwise provided on the face of the order, as accepted, delivery shall be made F.O.B. SPIR STAR’s facility.Regardless of the method of delivery, however, risk or loss shall pass to Customer upon SPIR STAR’s delivery to a carrier. Anydelivery dates shown are approximate and SPIR STAR shall have no liability for delays in delivery.

4. Changes, Reschedules and Cancellations: No change, rescheduling or cancellation of an order requested by Customer shall bevalid unless accepted by SPIR STAR in writing. Acceptance of any such requested change, rescheduling or cancellation shall beupon such terms and conditions as SPIR STAR requires.

5. Force Majeure: SPIR STAR does not assume the risk of, and shall not be liable for, delay or failure to perform any of SPIR STAR’sobligations by reason of circumstances beyond the reasonable control of SPIR STAR. Such circumstances include, but are limitedto: accidents; acts of God; strikes or other labor disputes; acts, laws, rules, or regulations of any governmental or quasi-governmen-tal agency; fires, floods, war or acts of terrorism; delays or failures in delivery of carriers or suppliers; or shortages of materials.

6. Documents and Notices: All documents passing between SPIR STAR and customer may be delivered according to the rules setforth below. Documents include, but are not limited to, the following: offers, acceptances, orders, invoices, statements, notices,letters, shop drawings, specifications, and change orders. Any Document required or permitted to be delivered shall be in writingand may be delivered: (a) personally; or (b) by United States Mail, postage prepaid, registered or certified mail, return receiptrequested, addressed to the parties at their respective addresses indicated on this credit application or a sales order, or at suchother addresses as may be specified by written notice delivered or sent in accordance herewith; or (c) by facsimile or electronic mail(“email”), at the respective numbers or email addresses indicated on the front page of this credit application, or at such othernumbers or addresses as may be specified by written notice delivered or sent in accordance herewith. Where delivery has beenmade personally, a receipt must be obtained from the persons signing this credit application or another member of upper manage-ment. Where delivery is by facsimile or email, the sender must use equipment that produces an authentication of transmission inprintable format and must retain a copy thereof. Commencement of time limitations dependent on notice are: (a) by personaldelivery, at the time of delivery; (b) by mail, 12:01 a.m. on the day that is 3 days from the date on the registered or certified mail receiptor the date of the last attempted delivery; or (c) by fax or email, 24 hours from the time of authenticated transmission.

TERMS AND CONDITIONS

7. Limited Warranty: SPIR STAR PROVIDES THE FOLLOWING LIMITED WARRANTY. THE TERM “HOSE” AS USED IN THIS LIMITEDWARRANTY SHALL INCLUDE COUPLERS AND END FITTING ASSEMBLIES (“EFAs”), IF AND ONLY IF, THEY ARE ATTACHED ORASSEMBLED ON THE HOSE BY SPIR STAR. SPIR STAR PROVIDES NO WARRANTY FOR THE COUPLERS OR EFAs AS INDI-VIDUAL COMPONENTS.


TERMS AND CONDITIONSULTRA HIGH PRESSURE HOSE (“UHP”) LIMITED WARRANTY: UHP is warranted to be free from defectsin material and workmanship for a period of 60 days of field use. Due to the variance in performance of certain pumps and relatedequipment and the potential for failure due to mishandling, abuse, misuse, accident, or alteration of the UHP, SPIR STAR reservesthe right to evaluate UHP that is claimed to have failed during the warranty period. Items that will void the warranty include, but arenot limited to:

· exceeding minimum bend radius;· exceeding pressure rating;· excessive temperatures;· excessive torquing of COUPLERS OR EFAs;· introduction of foreign particles into the UHP;· flexing near the COUPLER OR EFA of the UHP, and;· dragging or hauling equipment or other objects with the UHP.

If a failure occurs within the warranty period, Customer must submit the UHP for a warranty evaluation, by contacting SPIR STAR at800-890-7827. Please have the part number of the UHP, the serial number, and the purchase date or sales order number. If theinformation for the UHP meets the criteria for evaluation, SPIR STAR will issue a Returned Goods Authorization (“RGA”) number.The UHP may then be returned to SPIR STAR, freight prepaid (SPIR STAR to choose carrier and type of service). The RGA numbermust be clearly written on the shipping label and on all documentation submitted by the Customer. Upon receipt of the UHP bySPIR STAR, it will be inspected and evaluated to determine the cause of the failure. Upon completion of this evaluation, SPIR STARwill decide whether the failure was covered by the Limited Warranty. Please allow approximately 2 weeks for the evaluation. If thefailure is covered by the Limited Warranty, SPIR STAR will, at its discretion, either replace or repair the UHP at no cost to theCustomer or will apportion the cost, on a prorated basis, between itself and the Customer.

THIS LIMITED WARRANTY COMPRISES THE SOLE AND ENTIRE WARRANTY TO THE CUSTOMER. SPIR STAR MAKES NO OTHERREPRESENTATIONS OR WARRANTIES BY COURSE OF DEALING, USES OF TRADE, OR OTHERWISE, EXPRESSED OR IMPLIED.EXCEPT AS EXPRESSLY STATED BELOW, CUSTOMER HEREBY WAIVES ALL OTHER WARRANTIES, GUARANTEES, CONDITIONSOR LIABILITIES, EXPRESSED OR IMPLIED, ARISING BY LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY WARRANTYOF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE UNDER THE UNIFORM COMMERCIAL CODE. ANY WARRANTYCONTAINED HEREIN SHALL NOT BE EXTENDED, ALTERED, OR VARIED EXCEPT BY A WRITTEN INSTRUMENT SIGNED BY SPIRSTAR AND CUSTOMER.

8. Limitation of Remedy: SPIR STAR’S LIABILITY ARISING FROM OR IN ANY WAY CONNECTED WITH THE PRODUCTS SHALL BELIMITED EXCLUSIVELY TO REPAIR, PRORATION OF THE COST, OR REPLACEMENT, AS DECIDED BY SPIR STAR. IN NO EVENTSHALL SPIR STAR BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATUREWHATSOEVER, INCLUDING BUT NOT LIMITED TO, LOST PROFITS, CLAIMS FOR BREACH OF WARRANTY, WHETHER EX-PRESSED OR IMPLIED, BREACH OF CONTRACT, CLAIMS IN TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURETO WARN, STRICT LIABILITY OR DECEPTIVE TRADE PRACTICES ACT VIOLATIONS.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITA-TIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE FOREGOING LIMITATIONS MAY NOT APPLY. THIS LIMITEDWARRANTY GIVES THE CUSTOMER SPECIFIC LEGAL RIGHTS AND THE CUSTOMER MAY HAVE OTHER RIGHTS THAT VARY FROMJURISDICTION TO JURISDICATION.

9. Entire Agreement/Governing Law: The Terms set forth herein together with any amendments, modifications and any differentterms or conditions expressly accepted by SPIR STAR in writing, shall constitute the entire agreement concerning the productssold to Customer, and there are no oral or other representations or agreements which pertain thereto. This agreement shall begoverned in all respects by the law of the State of Texas.