table of contents 7.0 high hp low and medium voltageproii.ru/catalogs/qlmv_ge.pdf · 7.0 high hp...
TRANSCRIPT
7.0 High HP Low and Medium Voltage
7.1 Quantum™ LMV - TEFC Low Voltage
7.7 Quantum™ LMV - TEFC Medium Voltage
7.12 449 Frame TEFC
7.16 WPII, TEFC, TEAAC Standard Features
7.17 WPII Pricing and Kits
7.20 Pegasus™ MHV - WPII Pricing
7.21 Quantum™ LMV - TEFC Pricing
7.22 Pegasus™ MHV - TEAAC Pricing
7.23 Dimensions
TABLE OF CONTENTS
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Make a Difference
Imagine a motor that saves enough energy to pay for itself in 11/2 years.
Imagine that using it for one year saves enough energy to power 2 US households.
Imagine that this same motor reduces carbon dioxide emissions by 20 tons every year.
That’s the equivalent of planting an 5 acre forest.
Statements based on: replacement of a 100 HP 1800 RPM Pre-EPAct (Energy Policy Act of 1992) motor with a 100 HP 1800 RPM X$D Ultra® motor; Average Retail Price of Electricity for Industrial customers and Average [US] Residen-tial Monthly [electricity] Use per Energy Information Administration “Basic Electricity Statistics” for 2004 - http://www.eia.doe.gov; carbon dioxide US power plant emissions output rate for 2000 per US Envronmental Protection Agency “Clean Energy” - http://www.epa.gov/cleanerenergy/egrid; Emissions Reduction as Compared to Tree Plantings per www.epa.gov/appdstar/pdf/brochure.pdf. Actual efficiency improvement and benefits may vary based upon horsepower rating of replaced and replacement motor, performance characteristics of the replaced motor, hours of motor operation per year, actual cost of electricity and other factors.
The GE monogram, X$D Ultra and GEGARD2000 are trademarks and ecomagination is a service mark of the General Electric Company. NEMA Premium is a trademark of NEMA. ©2006 General Electric All rights reserved.
NEMA Premium Extra Severe Duty Motors
a product ofSM
www.gemotors.comX$DUltra®
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Qua
ntum
™ L
MV—
TEFC
7.1
Quantum™ LMV—TEFCSevere Duty Low Voltage
Standard Features
HP Range 350-600
Poles 2
Voltage 460, Usable at 400V 50 Hz 1.0 SF
Efficiency NEMA Premium (Meets or exceeds EISA efficiency requirements 350-500HP)
NEMA Design Standard Torque
Altitude 3300 ft
Ambient 40°C
Balance/Vibration 0.075 in/sec
Bearing Caps Both Ends
Bearing Protection IP55; Shaft slinger both ends
Bearing Type Single Shielded Ball
Conduit Box Cast Iron; Gasketed and rotatable in 90 degree increments
Drains Stainless Steel T-drains in lowest section of both endshields
Enclosure TEFC
End Shield Cast Iron
Fan Aluminum - Unidirectional
Fan Cover Fabricated Steel
Fasteners SAE Grade 5
Frame Material Cast Iron
Frame Size 509-5013
Frequency 60 or 50 Hz
Ground Ground in conduit box and 2 NEMA Type ground pads on frame
Insulation Class Class F
Insulation System Epoxy VPI
Inverter Capabilities Consult Factory
L10 Bearing Life Direct Coupled: 65,000 hrs
Leads Permanently numbered, Non-wicking
Lifting Means Two (2) cast in lifting lugs
Lubrication Polyurea Grease
Mounting Foot mounted F1 only, contact factory for F2 mounting options
Mounting Holes Dual drilled for 508/509, 5010/5011, 5012/5013 mounting
Nameplate 316 Stainless Steel
Paint Epoxyester Buff
Relubrication Yes, both ends; extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.15
Shaft Material AISI 1045
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine; IEEE 112 Method B
Thermal Protection 3 NC Thermostats
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 36 months from date of purchase or 42 months from date of shipment, whichever occurs first
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.2
Quantum
™ LM
V—TEFC
Quantum™ LMV—TEFCSevere Duty Low Voltage
Pricing
Severe Duty Low Voltage
HP RPM Volts Frame FLA Nom. Eff. Cat. No. List PricePrice
Symbol Norm. Stk. Wt. (lbs) C Dim. (in) Notes
350 3600 460 5011LS 364/366 95.8 Q527 $24,921 G4-7U5LV N 5200 74.14 106, 145
400 3600 460 5011LS 416/418 95.8 Q528 $26,420 G4-7U5LV N 5300 74.14 106, 145
450 3600 460 5011LS 468/470 95.8 Q529 $27,644 G4-7U5LV N 5375 74.14 106, 145
500 3600 460 5011LS 517/517 95.8 Q530 $28,630 G4-7U5LV N 5750 74.14 106, 145
600 3600 460 5013ST 617/620 95.8 Q531 $35,174 G4-7U5LV N 6700 83.13 106, 145
Severe Duty Low Voltage with C-Face
HP RPM Volts Frame FLA Nom. Eff. Cat. No. List PricePrice
Symbol Norm. Stk. Wt. (lbs) C Dim. (in) Notes
350 3600 460 5011LSC 364/366 95.8 Q522 $26,529 G4-7U5LV N 5200 75.08 106, 145
400 3600 460 5011LSC 416/418 95.8 Q523 $28,028 G4-7U5LV N 5300 75.08 106, 145
450 3600 460 5011LSC 468/470 95.8 Q524 $29,252 G4-7U5LV N 5375 75.08 106, 145
500 3600 460 5011LSC 517/517 95.8 Q525 $30,238 G4-7U5LV N 5750 75.08 106, 145
600 3600 460 5013STC 617/620 95.8 Q526 $36,782 G4-7U5LV N 6700 84.08 106, 145
Notes:106 Usable on 400V, 50 Hz at 1.0 service factor145 CCW rotation facing opposite drive end. For CW fans use Part #148C8070AA1; except for 350 HP 3600 RPM motors use #148C8070BA1
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Qua
ntum
™ L
MV—
TEFC
7.3
Quantum™ LMV—TEFCSevere Duty Low Voltage
Typical Performance Data
Volts: 460 Frequency: 60 Hz HP: 350-600
HPFL
RPMNP FLA
Design LRA
Code KVA/HP
FLT (lb-ft)
LRT (lb-ft)
BDT (lb-ft)
NP Eff. Full
Load
75% Load Eff.
50% Load Eff.
NP PF Full
Load
75% Load
Power Factor
50% Load
Power Factor
Max KVAR
350 3565 364.0 2306.0 G 515.6 526.9 1330.2 95.8 95.6 94.9 94.0 93.6 91.4 42.1
400 3565 416.0 2631.4 G 589.2 595.1 1507.8 95.8 95.6 94.9 94.0 93.4 91.0 49.8
450 3565 468.0 2969.2 G 663.0 700.8 1698.6 95.8 95.8 95.2 94.0 93.8 91.6 53.1
500 3560 517.0 3310.2 G 737.0 824.0 1878.6 95.8 96.0 95.5 94.5 94.2 92.3 54.7
600 3570 617.0 3791.8 G 882.4 734.2 2153.9 95.8 96.4 96.1 95.0 94.8 93.4 56.8
Note: Performance data is the same for standard and C-Face motors.
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.4
Quantum
™ LM
V—TEFC
Quantum™ LMV—TEFCSevere Duty Low Voltage with IEEE 841 Features
Standard Features
HP Range 300-500
Poles 2,4,6
Voltage 460
Efficiency NEMA Premium (Meets or exceeds IEEE 841-2009 efficiency requirements)
NEMA Design Standard Torque
Altitude 3300 ft
Ambient 40°C to -25°C
Balance/Vibration 0.075 in/sec
Bearing Caps Both Ends
Bearing Protection IP55; Inpro Seal on both ends
Bearing Type Single Shielded Ball
Conduit Box Cast Iron; Gasketed and rotatable in 90 degree increments
Div 2 Temp Codes Motors have an Auto Ignition Temperature of 200 or 215 degree C stamped on the nameplate. (See notes)
Drains Stainless Steel T-drains in lowest section of both endshields
Enclosure TEFC
End Shield Cast Iron
Fan Aluminum (Unidirectional on 2 poles)
Fan Cover Fabricated Steel
Fasteners SAE Grade 5
Foot Draft Angle +/- 1.5 degrees
Foot Flatness 0.005 in
Frame Material Cast Iron
Frame Size 509-5013
Frequency 60 Hz
Ground Ground in conduit box and 2 NEMA Type ground pads on frame
Insulation Class Class F
Insulation System Epoxy VPI
Inverter Capabilities Consult Factory
L10 Bearing Life Direct Coupled: 130,000 hrs 4&6 pole; 65,000 hrs 2 pole
Leads Permanently numbered, Non-wicking
Lifting Means Two (2) cast in lifting lugs
Lubrication Polyurea Grease
Mounting Foot mounted F1 only, contact factory for F2 mounting options
Mounting Holes Dual drilled for 508/509, 5010/5011, 5012/5013 mounting
Nameplate 316 Stainless Steel
Oil Mist Lube Includes provisions for conversion to Oil Mist Lubrication
Paint Epoxyester Buff
Relubrication Yes, both ends; extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.15
Shaft Material AISI 1045
Shaft TIR Meets IEEE 841, 0.0015 in
Special Painting Meets IEEE 841
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine Report including vibration supplied with motor, IEEE 112 Method B
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 60 months from date of purchase or 66 months from date of shipment, whichever occurs first
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Qua
ntum
™ L
MV—
TEFC
7.5
Quantum™ LMV—TEFCSevere Duty Low Voltage with IEEE 841 Features
Pricing
HP RPM Volts Frame FLA Nom. Eff. Cat. No. List PricePrice
Symbol Norm. Stk. Wt. (lbs) C Dim. (in) Notes
300 1200 460 509LL 339 95.8 Q808 $25,810 G4-7U5XLV Y 4650 67.13 146
350 3600 460 5011LS 364 95.8 Q800 $25,154 G4-7U5XLV Y 5400 74.14 112, 145, 146
350 1800 460 5011LL 378 96.2 Q804 $26,112 G4-7U5XLV Y 5600 75.14 146
350 1200 460 5011LL 391 95.8 Q809 $29,425 G4-7U5XLV N 5150 75.14 146
400 3600 460 5011LS 416 95.8 Q801 $26,699 G4-7U5XLV Y 5400 74.14 112, 145, 146
400 1800 460 5011LL 432 96.2 Q805 $26,225 G4-7U5XLV Y 5700 75.14 146
400 1200 460 5011LL 452 95.8 Q810 $30,710 G4-7U5XLV Y 5400 75.14 146
450 3600 460 5011LS 468 95.8 Q802 $28,022 G4-7U5XLV Y 5475 74.14 112, 145, 146
450 1800 460 5013S 484 96.2 Q806 $32,506 G4-7U5XLV N 6275 85.13 146, 147
450 1200 460 5011LL 508 95.8 Q811 $33,053 G4-7U5XLV N 5700 75.14 146
500 3600 460 5011LS 517 95.8 Q803 $29,278 G4-7U5XLV Y 5750 74.14 112, 145, 146, 147
500 1800 460 5013S 538 96.2 Q807 $33,804 G4-7U5XLV N 6750 85.13 146, 147
Notes:112 Noise level exceeds IEEE 841145 CCW rotation facing opposite drive end. For CW fans use Part #148C8070AA1; except for 350 HP 3600 RPM motors use #148C8070BA1146 Aluminum fan. Aluminum fan complies with API541147 Motors have an Auto Ignition Temperature of 215 degree C stamped on the nameplate
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.6
Quantum
™ LM
V—TEFC
Quantum™ LMV—TEFCSevere Duty Low Voltage with IEEE 841 Features
Typical Performance Data
Volts: 460 HP: 300-500
HPFL
RPMNP FLA
Design LRA
Code KVA/HP
FLT (lb-ft)
LRT (lb-ft)
BDT (lb-ft)
NP Eff. Full
Load
75% Load Eff.
50% Load Eff.
NP PF Full
Load
75% Load
Power Factor
50% Load
Power Factor
Max KVAR
300 1185 339.0 2012.0 G 1327.2 1558.1 3497.2 95.8 96.0 95.8 86.5 84.1 77.2 73.5
350 3560 364.0 2231.7 G 515.8 516.8 1290.0 95.8 95.6 94.9 94.0 93.9 91.9 39.8
350 1785 378.0 2270.9 G 1029.1 1088.8 2550.1 96.2 96.5 96.4 90.0 88.7 84.0 64.2
350 1185 391.0 2388.1 G 1549.4 1986.3 4112.1 95.8 96.1 96.1 87.5 85.6 79.3 78.7
400 3565 416.0 2631.4 G 589.2 595.1 1507.8 95.8 95.6 94.9 94.0 93.4 91.0 49.8
400 1785 432.0 2609.6 G 1176.1 1234.9 2955.5 96.2 96.5 96.5 90.0 88.4 83.4 75.5
400 1190 452.0 2694.3 G 1765.1 2058.1 4453.3 95.8 96.4 96.3 86.5 84.5 77.9 94.3
450 3565 468.0 2969.2 G 663.0 700.8 1698.6 95.8 95.8 95.2 94.0 93.8 91.6 53.1
450 1785 484.0 2962.2 G 1323.3 1472.8 3312.2 96.2 96.3 96.2 90.5 89.1 84.5 80.5
450 1190 508.0 3178.9 G 1984.4 2399.1 5280.5 95.8 96.6 96.5 86.5 83.7 76.4 112.9
500 3560 517.0 3310.2 G 737.0 824.0 1878.6 95.8 96.0 95.5 94.5 94.2 92.3 54.7
500 1785 538.0 3304.9 G 1470.4 1676.3 3676.0 96.2 96.5 96.3 90.5 89.3 84.9 87.2
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Qua
ntum
™ L
MV—
TEFC
7.7
Quantum™ LMV—TEFCSevere Duty Medium Voltage
Standard Features
HP Range 200-600
Poles 2,4,6
Voltage 2300/4000
Efficiency NEMA Premium
NEMA Design Standard Torque
Altitude 3300 ft
Ambient 40°C
Balance/Vibration 0.075 in/sec Ball Bearing; Roller Bearing 6 Pole 0.0010 in (P-P)
Bearing Caps Both Ends
Bearing Protection Shaft Slinger Both Ends
Bearing Temp Device 100 Ohm Platinum RTD both bearings
Bearing Type Single Shielded Ball; 509L & 5011L have DE Roller Bearing
Conduit Box Cast Iron
Drain Stainless Steel T-drains in lowest section of both endshields
Enclosure TEFC
End Shield Cast Iron
Fan Aluminum (Unidirectional on 2 poles)
Fan Cover Fabricated Steel
Fasteners SAE Grade 5
Frame Material Cast Iron
Frame Size 509-5013
Frequency 60 Hz
Ground Ground in conduit box and 2 NEMA Type ground pads on frame
Insulation Class Class F
Insulation System Epoxy VPI
Inverter Capabilities Consult Factory
L10 Bearing Life Direct Coupled: 130,000 hrs 4&6 pole; 65,000 hrs 2 pole; Belted 26,280 hrs
Leads Permanently numbered, Non-wicking
Lifting Means Two (2) cast in lifting lugs
Lubrication Polyurea Grease
Mounting Foot mounted F1 only, contact factory for F2 mounting options
Mounting Holes Dual drilled for 508/509, 5010/5011, 5012/5013 mounting
Nameplate 316 Stainless Steel
Paint Epoxyester Buff
Relubrication Yes, both ends; extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.15, except 600HP 6 pole 1.0 SF only
Shaft Material AISI 1045; 509L & 5011L AISI 4140
Space Heater 115 volt standard space heaters, leads to main conduit box
Stator Temp Device 100 Ohm Platinum Stator RTD’s, leads to accessory box
Temperature Rise 80°C @ 1.0 SF, 600HP 6 pole Class F rise @ 1.0 SF
Tests NEMA Routine; IEEE 112 Method B
Time Rating Continuous
Vibration Pads Cast in vibration pads for repeatable measurements
Warranty 36 months from date of purchase or 42 months from date of shipment, whichever occurs first
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.8
Quantum
™ LM
V—TEFC
Quantum™ LMV—TEFCSevere Duty Medium Voltage
Pricing
HP RPM Volts Frame FLA Nom. Eff. Cat. No. List PricePrice
Symbol Norm. Stk. Wt. (lbs) C Dim. (in) Notes
200 1200 2300/4000 509L 46.6/26.8 95.0 Q514 $36,028 G4-7U5MV Y 4450 72.38 148
250 3600 2300/4000 509LS 53.2/30.6 95.0 Q500 $35,227 G4-7U5MV Y 4650 66.13 145
250 1800 2300/4000 509LL 55.3/31.8 95.0 Q507 $33,434 G4-7U5MV Y 4350 67.13
250 1200 2300/4000 509L 57.9/33.3 95.0 Q515 $37,455 G4-7U5MV Y 4475 72.38 148
300 3600 2300/4000 509LS 63.5/36.5 95.0 Q501 $36,844 G4-7U5MV Y 4500 66.13 145
300 1800 2300/4000 509LL 66.1/38 95.0 Q508 $34,833 G4-7U5MV Y 4550 67.13
300 1200 2300/4000 5011L 68.5/39.4 95.4 Q516 $39,606 G4-7U5MV Y 5400 80.39 148
350 3600 2300/4000 5011LS 73.7/42.4 95.0 Q502 $41,513 G4-7U5MV Y 4950 74.14 145
350 1800 2300/4000 5011LL 77.6/44.6 95.4 Q509 $36,302 G4-7U5MV N 5200 75.14
350 1200 2300/4000 5011L 80.7/46.4 95.0 Q517 $40,554 G4-7U5MV Y 5500 80.39 148
400 3600 2300/4000 5011LS 83.8/48.2 95.0 Q503 $42,266 G4-7U5MV Y 5300 74.14 145
400 1800 2300/4000 5011LL 87.7/50.4 95.0 Q510 $38,116 G4-7U5MV Y 5800 75.14
400 1200 2300/4000 5011L 93.9/54 95.0 Q518 $43,272 G4-7U5MV Y 5700 80.39 148
450 3600 2300/4000 5011LS 93.9/54 95.4 Q504 $44,106 G4-7U5MV Y 5550 74.14 145
450 1800 2300/4000 5013S 99.1/57 95.0 Q511 $43,492 G4-7U5MV N 6500 85.13
450 1200 2300/4000 5013S 103.7/59.6 95.0 Q519 $47,547 G4-7U5MV N 6600 85.13 148
500 3600 2300/4000 5013ST 103.8/59.7 95.4 Q505 $47,559 G4-7U5MV Y 6350 83.13 145
500 1800 2300/4000 5013S 109.4/62.9 95.0 Q512 $46,369 G4-7U5MV N 7000 85.13
500 1200 2300/4000 5013S 114.6/65.9 95.0 Q520 $48,693 G4-7U5MV N 7150 85.13 148
600 3600 2300/4000 5013ST 124.5/71.6 95.4 Q506 $49,136 G4-7U5MV N 6700 83.13 145
600 1800 2300/4000 5013S 130.4/75 96.2 Q513 $55,844 G4-7U5MV Y 7150 85.13
600 1200 2300/4000 5013S 138.3/79.5 95.0 Q521 $50,855 G4-7U5MV N 7150 85.13 149
Notes:145 CCW rotation facing opposite drive end. For CW fans use Part #148C8070AA1; except for 350 HP 3600 RPM motors use #148C8070BA1148 Roller bearing on drive end. High strength shaft material. For belted loads only. Refer to Belt Drive Table in Application Guide.149 Class F rise at 1.0 SF only
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Qua
ntum
™ L
MV—
TEFC
7.9
Quantum™ LMV—TEFCSevere Duty Medium Voltage
Typical Performance Data
Volts: 4000 HP: 200-600
HPFL
RPMNP FLA
Design LRA
Code KVA/HP
FLT (lb-ft)
LRT (lb-ft)
BDT (lb-ft)
NP Eff. Full
Load
75% Load Eff.
50% Load Eff.
NP PF Full
Load
75% Load
Power Factor
50% Load
Power Factor
Max KVAR
200 1185 26.8 156.4 G 885.3 1183.6 2299.1 95.0 95.4 95.2 84.5 81.0 72.4 58.2
250 3575 30.6 272.5 J 367.0 521.5 1328.2 95.0 94.3 92.9 92.5 90.5 85.0 49.2
250 1785 32.0 177.6 G 736.3 736.3 1766.4 95.0 95.1 94.6 88.5 87.0 81.5 52.7
250 1190 33.3 195.4 G 1103.5 1270.1 2774.2 95.0 95.4 95.1 85.0 82.0 74.0 69.4
300 3575 36.5 244.5 G 440.6 338.8 1198.4 95.0 94.8 93.7 93.0 92.1 88.5 46.5
300 1780 38.0 209.1 G 883.7 911.1 2067.0 95.0 95.5 95.2 89.5 88.0 83.1 57.6
300 1190 39.4 241.9 G 1323.6 1666.4 3399.0 95.4 95.8 95.6 86.0 83.0 75.4 78.6
350 3575 42.4 281.0 G 514.2 405.7 1376.0 95.0 95.2 94.3 93.5 92.7 89.5 50.1
350 1785 44.6 280.4 G 1029.1 1240.1 2790.9 95.4 96.0 95.5 88.5 86.5 80.2 77.7
350 1190 46.4 276.9 G 1544.8 1884.7 3934.6 95.0 95.9 95.7 85.5 82.8 75.2 92.3
400 3575 48.2 318.4 G 587.8 485.5 1558.3 95.0 95.5 94.8 94.0 93.4 90.8 51.7
400 1785 50.4 290.1 G 1178.1 1407.8 2808.6 95.0 96.1 95.8 90.0 88.8 84.5 70.9
400 1190 54.0 342.2 G 1763.7 2273.4 4910.1 95.0 96.0 95.7 84.0 80.5 71.5 120.8
450 3570 54.0 354.8 G 661.4 560.9 1737.5 95.4 95.7 95.1 94.0 93.7 91.3 55.0
450 1785 57.0 345.6 G 1324.0 1635.1 3388.1 95.0 96.4 96.0 89.5 88.1 83.0 86.8
450 1190 59.6 355.7 G 1985.9 2452.6 5081.9 95.0 96.2 96.0 85.5 82.9 75.3 117.1
500 3570 59.7 393.0 G 734.8 637.1 1936.9 95.4 96.0 95.4 94.5 94.0 91.8 58.1
500 1785 63.3 377.0 G 1471.5 1807.0 3684.6 95.0 96.5 96.2 89.5 88.4 83.6 92.6
500 1190 65.9 397.2 G 2206.8 2831.3 5640.6 95.0 96.3 96.2 86.0 83.5 76.3 125.2
600 3575 71.6 495.5 G 881.7 841.1 2447.6 95.4 96.3 95.9 94.5 94.1 91.9 69.6
600 1785 75.0 614.7 H 1762.3 3184.5 5917.8 96.2 96.8 96.5 89.5 86.7 79.7 138.0
600 1190 79.5 485.8 G 2649.0 3499.3 6945.7 95.0 96.3 96.2 85.5 83.0 75.4 155.8
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.10
Quantum
™ LM
V—TEFC
Quantum™ LMV—TEFC
Dimensions
Dimensions refer to drawings on following page
Frame 500, Totally Enclosed Fan Cooled
Frame
Shaft Mounting
A B C D3 G J K L O P
Keyway Key Length N-W U1 V2Width Depth E H BA 2F 2XF
508L 1.000 0.500 10.00 12.00 3.875 11.50 10.00 1.07 8.50 - 25.00 23.00 31.90 72.39 12.50 1.35 7.00 8.36 37.88 30.80 30.45
508LL 0.875 0.437 5.00 6.75 3.375 6.50 10.00 1.07 8.50 - 25.00 23.00 31.90 67.14 12.50 1.35 7.00 8.36 37.88 30.80 30.45
508LS 0.625 0.312 4.00 5.75 2.625 5.50 10.00 1.07 8.50 - 25.00 23.00 31.90 66.14 12.50 1.35 7.00 8.36 37.88 30.80 30.45
509L 1.000 0.500 10.00 12.00 3.875 11.50 10.00 1.07 8.50 28.00 - 23.00 31.90 72.39 12.50 1.35 7.00 8.36 37.88 30.80 30.45
509LL 0.875 0.437 5.00 6.75 3.375 6.50 10.00 1.07 8.50 28.00 - 23.00 31.90 67.14 12.50 1.35 7.00 8.36 37.88 30.80 30.45
509LS 0.625 0.312 4.00 5.75 2.625 5.50 10.00 1.07 8.50 28.00 - 23.00 31.90 66.14 12.50 1.35 7.00 8.36 37.88 30.80 30.45
5010L 1.000 0.500 10.00 12.00 3.875 11.50 10.00 1.07 8.50 - 32.00 23.00 39.90 80.39 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5010LL 0.875 0.437 5.00 6.75 3.375 6.50 10.00 1.07 8.50 - 32.00 23.00 39.90 75.14 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5010LS 0.625 0.312 4.00 5.75 2.625 5.50 10.00 1.07 8.50 - 32.00 23.00 39.90 74.14 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5011L 1.000 0.500 10.00 12.00 3.875 11.50 10.00 1.07 8.50 36.00 - 23.00 39.90 80.39 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5011LL 0.875 0.437 5.00 6.75 3.375 6.50 10.00 1.07 8.50 36.00 - 23.00 39.90 75.14 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5011LS 0.625 0.312 4.00 5.75 2.625 5.50 10.00 1.07 8.50 36.00 - 23.00 39.90 74.14 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5012S 1.000 0.500 5.50 7.75 3.875 7.50 10.00 1.07 8.50 - 40.00 23.00 48.90 85.14 12.50 1.35 7.00 10.00 46.38 30.80 30.45
5012ST 0.750 0.375 4.00 5.75 2.875 5.50 10.00 1.07 8.50 - 40.00 23.00 48.90 83.13 12.50 1.35 7.00 10.00 46.38 30.80 30.45
5013S 1.000 0.500 5.50 7.75 3.875 7.50 10.00 1.07 8.50 45.00 - 23.00 48.90 85.14 12.50 1.35 7.00 10.00 46.38 30.80 30.45
5013ST 0.750 0.375 4.00 5.75 2.875 5.50 10.00 1.07 8.50 45.00 - 23.00 48.90 83.13 12.50 1.35 7.00 10.00 46.38 30.80 30.45
Frame 500, Totally Enclosed Fan Cooled with C Face
Frame
Shaft Mounting
A B C D3 G J K L O P
Keyway Key Length N-W U1 V2Width Depth E H BA 2F 2XF
5010LSC 0.625 0.312 4.00 5.75 2.625 5.50 10.00 1.07 - - 32.00 23.00 39.90 75.09 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5011LSC 0.625 0.312 4.00 5.75 2.625 5.50 10.00 1.07 - 36.00 - 23.00 39.90 75.09 12.50 1.35 7.00 10.00 41.88 30.80 30.45
5012STC 0.750 0.375 4.00 5.75 2.875 5.50 10.00 1.07 - - 40.00 23.00 48.90 84.09 12.50 1.35 7.00 10.00 46.38 30.80 30.45
5013STC 0.750 0.375 4.00 5.75 2.875 5.50 10.00 1.07 - 45.00 - 23.00 48.90 84.09 12.50 1.35 7.00 10.00 46.38 30.80 30.45
Conduit Box Dimensions
FrameMax.
FL Amps5Approx. Volume AA AB AC4 AD4 AF XL XN R
508-5013 400 1260 2-4.00 21.53 18.16 6.41 9.42 12.39 16.25 34.03
508-5013 600 2500 2-4.00 22.74 19.19 6.38 - 12.00 22.69 35.24
508-5013 1200 5700 3-3.00 27.75 22.80 3.71 8.66 20.00 20.00 40.25
Notes:1 Tolerance on “U” dimension will be +0.000 inch - 0.0012 Dimension “V” represents length of straight part of shaft extension3 Tolerance on “D” dimension will be + 0.000 inch - 0.060 inch4 Dimension to AA hole5 Conduit box size is determined by full load amps
Providing mounting conditions permit, conduit box may be turned so that entrance can be made upward, downward or from either side
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Qua
ntum
™ L
MV—
TEFC
7.11
Quantum™ LMV—TEFC
Dimensions
Frame dimensions on previous page
Frame 500, Totally Enclosed Fan Cooled
Frame 500, Totally Enclosed Fan Cooled with C Face
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.12
449 Frame TEFC
449 Frame TEFCSevere Duty Medium Voltage
Standard Features
HP Range 125-200
Poles 2,4,6
Voltage 2300 (200HP 4 pole 2300/4000V)
Efficiency Premium
NEMA Design B
Altitude 3300 ft
Ambient 40°C, Alternate rating 65°C @ 1.0 SF except as noted
Balance/Vibration 0.055 in/sec Ball Bearing; Roller Bearing 6 Pole 0.0005 in (P-P)
Bearing Caps Both Ends
Bearing Protection Shaft Slinger Both Ends
Bearing Type Single Shielded Ball; 125HP & 150HP 6 pole have DE Roller Bearing
Conduit Box Cast Iron; 200HP 4 pole Fabricated Steel
Drain Stainless Steel T Drains in lowest section of both endshields
Enclosure TEFC
End Shield Cast Iron
Fan Bidirectional Non Sparking Plastic
Fan Cover Cast Iron
Fasteners SAE Grade 5
Frame Material Cast Iron
Frame Size 447/449
Frequency 60 Hz
Ground Ground in conduit box
Insulation Class Class F
Insulation System Epoxy VPI
Inverter Capabilities Consult Factory
L10 Bearing Life Direct Coupled: 130,000 hrs 4&6 pole; 65,000 hrs 2 pole; Belted 26,280 hrs
Leads Permanently Numbered, Non-wicking
Lifting Means Two (2) cast in lifting lugs
Lubrication Ball Bearing Polyurea
Mounting Foot mounted F1 only
Mounting Holes 2 per foot
Nameplate 316 Stainless Steel
Paint Epoxyester Buff
Relubrication Yes, both ends; extended through the fan cover
Rotor Cast Aluminum
Service Factor 1.15
Shaft Material 2&4 Pole AISI 1045; 6 Pole AISI 4140
Temperature Rise 80°C @ 1.0 SF
Tests NEMA Routine; IEEE 112 Method B
Time Rating Continuous
Warranty 36 months from date of purchase or 42 months from date of shipment, whichever occurs first
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
449
Fram
e TE
FC
7.13
449 Frame TEFCSevere Duty Medium Voltage
Pricing
449 Frame
HP RPM Volts Frame FLA Nom. Eff. Cat. No. List PricePrice
Symbol Norm. Stk. Wt. (lbs) C Dim. (in) Notes
125 3600 2300 447TS 26.9 93.0 E9520 $18,884 G4-7TAN N 2490 50.06
125 1800 2300 449T 28.8 95.0 E9523 $18,691 G4-7TAN N 2490 53.81
125 1200 2300 449T 32.1 94.1 E9526 $19,024 G4-7TAN N 2750 53.81 148
150 3600 2300 449TS 32.1 93.0 E9521 $20,182 G4-7TAN Y 2610 50.06
150 1800 2300 449T 34.8 95.0 E9524 $19,318 G4-7TAN Y 2610 53.81
150 1200 2300 449T 38.3 94.1 E9527 $19,636 G4-7TAN N 2750 53.81 148
200 3600 2300 449TS 42.8 93.6 E9522 $21,609 G4-7TAN Y 2610 50.06 149, 150
200 1800 2300/4000 449T 45.2/26.0 95.0 E9525 $20,955 G4-7TAN Y 2720 53.81 150
Notes:148 Roller bearing on drive end. High strength shaft material. For belted loads only. Refer to Belt Drive Table in Application Guide.149 Class F rise @ 1.0 SF only150 Does not meet alternate rating of 65°C @ 1.0 SF
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.14
449 Frame TEFC
449 Frame TEFCSevere Duty Medium Voltage
Typical Performance Data
Volts: 2300, 2300/4000 HP: 125-200
HPFL
RPMNP FLA
Design LRA
Code KVA/HP
FLT (lb-ft)
LRT (lb-ft)
BDT (lb-ft)
NP Eff. Full
Load
75% Load Eff.
50% Load Eff.
NP PF Full
Load
75% Load
Power Factor
50% Load
Power Factor
Max KVAR
125 3570 26.9 171.2 G 183.8 309.3 400.5 93.0 93.0 91.9 93.5 93.5 91.9 14.1
125 1785 28.8 165.4 G 367.7 696.8 813.7 95.0 95.1 94.4 85.5 82.4 74.6 34.7
125 1190 32.1 176.8 G 552.0 999.7 1137.1 94.1 94.4 93.7 77.5 72.9 62.4 49.7
150 3570 32.3 212.9 G 220.5 409.2 499.4 93.0 93.7 92.8 93.5 93.8 92.2 16.5
150 1785 34.8 209.8 G 441.0 903.2 1034.6 95.0 95.3 94.7 85.0 81.9 73.6 43.2
150 1190 38.3 215.5 G 662.6 1291.4 1401.4 94.1 94.6 94.0 78.0 73.5 63.3 58.0
200 3570 42.8 274.4 G 294.3 537.1 648.9 93.6 94.2 93.6 93.5 93.9 92.4 21.3
200 1785 26.0 154.8 G 587.6 998.3 1275.1 95.0 95.2 94.8 87.0 85.0 78.4 48.2
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
449 Frame TEFCSevere Duty Medium Voltage
Dimensions
449 Frame, Totally Enclosed Fan Cooled
Frame
Shaft Mounting
A B C D3 G J K L O P
Keyway Key Length N-W U1 V2Width Depth E H BA BS 2F 2XF
447TS 0.625 0.625 3.00 4.75 2.375 4.50 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 50.06 11.00 1.47 2.61 8.91 25.31 22.98 23.08
449TS 0.625 0.625 3.00 4.75 2.375 4.50 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 50.06 11.00 1.47 2.61 8.91 25.31 22.98 23.08
449T 0.875 0.875 6.88 8.50 3.375 8.25 9.00 0.81 7.50 12.50 25.00 20.00 20.00 27.30 58.31 11.00 1.47 2.61 8.91 25.31 22.98 23.08
Conduit Box Dimensions
FrameMax.
FL Amps5Approx. Volume AA AB AC4 AF XL XN
447-449 250 700 8-3.00 20.81 16.68 7.00 12.14 10.50
447-449 250 2500 2-4.00 22.05 16.93 7.78 13.68 27.25
Notes:1 Tolerance on “U” dimension will be +0.000 inch - 0.0012 Dimension “V” represents length of straight part of shaft extension3 Tolerance on “D” dimension will be + 0.000 inch - 0.060 inch4 Dimension to AA hole5 Conduit box size is determined by full load amps
Providing mounting conditions permit, conduit box may be turned so that entrance can be made upward, downward or from either side
449
Fram
e TE
FC
7.15
GE Energy Section 7 – Medium Voltage
7.1 Data subject to change without notice. GEP-500U 01/10 www.gemotors.com 800 541 7191
Medium Voltage WP-II Above NEMA (2300/4000 Volts) 509-5011 Frames
Standard Features
HP Range 400 - 800
Poles 2, 4
Voltage 2300/4000
Efficiency Standard
NEMA Design As noted
Altitude 1000 meters
Ambient 40 degree C
Balance/Vibration Standard per NEMA MG1
Bearing Caps Ball Bearing only
Bearing Temp Device 100 Platinum RTD both bearings
Bearing Type Ball or Sleeve as noted
Conduit Box 2500 cu in
Constant Level Oilers Provided on sleeve bearings
Enclosure WPII
End Shield Cast iron
Fasteners SAE
Frame Material Cast iron
Frame Size 509 - 5011
Frequency 60 Hz
Ground Ground in conduit box and frame
Insulation Class Class F
Insulation System Form coil epoxy VPI
Inverter Capabilities Consult Factory
Leads 6 leads
Lifting Means Four (4) cast in lifting lugs
Lubrication Ball bearing Polyurea, Sleeve bearing oil
Mounting Foot mounted F1 only (not convertible to F2)
Mounting Holes One per foot
Nameplate Stainless Steel
Paint Epoxyester Gray
Relubrication Yes, both ends
Roller Bearing Field conversion available
Rotor Aluminum
Service Factor 1.15
Shaft Material ANSI 1045
Space Heater Thermostatically controlled space heaters, 115 volt, 200 watt. Leads to a Condulet
Stator Temp Device 100 platinum Stator RTD’s, leads to accessory box
Temperature Rise As noted
Tests NEMA Routine; IEEE 112 Method B
Time Rating Continuous
Vertical Jack Screws Standard
Warranty 12 months from date of installation or 18 months from date of manufacture, whichever occurs first
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium Voltage WP-IIAbove NEMA (2300/4000 Volts)509-5011 Frames
Standard Features
7.16
Medium
Voltage
GE Energy Section 7 – Medium Voltage
7.2 Data subject to change without notice. GEP-500U 01/10 www.gemotors.com 800 541 7191
Medium Voltage WP-II Above NEMA (2300/4000 Volts) 509-5011 Frames
Pricing and Kits
Weather Protected II
HP RPM Volts Frame SF FLA Cat. No. GE WP-II List Price Price Symbol Norm. Stk. Wt. (lbs)
C Dim. (in.) Notes
400 1800 2300/4000 509L 1.15 86.4/49.7 S3405 $34,264 G6-7DAN Y 3620 56.9 6
450 1800 2300/4000 509L 1.15 97.7/56.2 S3405 $34,264 G6-7DAN Y 3620 56.9
500 1800 2300/4000 509L 1.15 109.6/63.0 S3405 $34,264 G6-7DAN Y 3620 56.9
400 3600 2300/4000 509LS 1.15 86.4/49.7 S3406 $34,977 G6-7DAN Y 3620 50.65 6
450 3600 2300/4000 509LS 1.15 97.2/55.9 S3406 $34,977 G6-7DAN Y 3620 50.65
500 3600 2300/4000 509LS 1.15 108.2/62.2 S3406 $34,977 G6-7DAN Y 3620 50.65
600 3600 2300/4000 509LS 1.15 132.0/75.9 S3406 $34,977 G6-7DAN Y 3620 50.65 133
400 3600 2300/4000 509LS 1.15 86.4/49.7 S3427 $37,477 G6-7DAN Y 3620 50.65 4,6
450 3600 2300/4000 509LS 1.15 97.2/55.9 S3427 $37,477 G6-7DAN Y 3620 50.65 4
500 3600 2300/4000 509LS 1.15 108.2/62.2 S3427 $37,477 G6-7DAN Y 3620 50.65 4
600 3600 2300/4000 509LS 1.15 132.0/75.9 S3427 $37,477 G6-7DAN Y 3260 50.65 4, 133
500 1800 2300/4000 5011L 1.15 107.3/61.7 S3411 $43,009 G6-7DAN Y 4710 64.9 6
600 1800 2300/4000 5011L 1.15 129.2/74.3 S3411 $43,009 G6-7DAN Y 4710 64.9 133
700 1800 2300/4000 5011L 1.15 153.0/88.0 S3411 $43,009 G6-7DAN Y 4710 64.9 133
600 3600 2300/4000 5011LS 1.15 127.1/73.1 S3430 $46,155 G6-7DAN Y 4710 58.65 4, 133
700 3600 2300/4000 5011LS 1.15 149.0/85.7 S3430 $46,155 G6-7DAN Y 4710 58.65 4, 133
800 3600 2300/4000 5011LS 1.15 172.9/99.4 S3430 $46,155 G6-7DAN Y 4710 58.65 4, 133
Bearing Conversion Kit Designed to convert drive end ball bearing to roller bearing with the recommended ISO roller bearing. For 509-5011 GE frames (4, 6, and 8 pole only) stock motors. Roller bearing supplied. Contact factory for eligible models.
Cat. No. Part No. Frame List Price Price Symbol Norm. Stk.
A927 249A4321AG-G01 509-5011 $360 G6-7KITS N
Notes: 4 Sleeve Bearing 6 NEMA Design A 133 Above NEMA Defined Electrical Design All Ratings are foot mounted F1 only (not convertible to F2) Catalog number S3405 has nameplate stamping for 400HP, 450HP and 500HP ratings Catalog number S3406 has nameplate stamping for 400HP, 450HP, 500HP and 600HP ratings Catalog number S3427 has nameplate stamping for 400HP, 450HP, 500HP and 600HP ratings—all with sleeve bearings Catalog number S3411 has nameplate stamping for 500HP, 600HP and 700HP ratings Catalog number S3430 has nameplate stamping for the 600HP, 700HP and 800HP ratings
Notes: Application of this kit requires load confirmation with factory and is for the 320 bearing size
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium Voltage WP-IIAbove NEMA (2300/4000 Volts)509-5011 Frames
Pricing and Kits
Med
ium
Vol
tage
7.17
ygrenEEG Section 7 – Medium Voltage
01/10U005-PEG.ecitontuohtiwegnahcottcejbusataD3.7www.gemotors.com
1917145008
Medium Voltage WP-II Above NEMA (2300/4000 Volts)
Dimensions
Weather Protected II
500 Frame
Dimensions in Inches
Shaft Mounting
Keyway
Frame
Approx. Net Wt. In
Lbs. Width Depth Key
Length N-W U (1) V (2) BA D (3) E F H A B C G J K L O P
509L 3300 1.000 0.500 10.0 12.00 3.875 11.75 8.5 12.5 10 14.0 1.06 26 32.6 56.90 1.1 5 6.5 22.40 45.26 42.2
509LS 3300 0.625 0.312 4.0 5.75 2.625 5.50 8.5 12.5 10 14.0 1.06 26 32.6 50.65 1.1 5 6.5 22.40 45.26 42.2
509LL 3300 0.875 0.437 5.0 6.75 3.375 6.50 8.5 12.5 10 14.0 1.06 26 32.6 51.65 1.1 5 6.5 22.40 45.26 42.2
5011L 4100 1.000 0.500 10.0 12.00 3.875 11.75 8.5 12.5 10 18.0 1.06 23 40.6 64.90 1.1 5 6.5 26.40 45.26 42.2
5011LS 4100 0.625 0.312 4.0 5.75 2.625 5.50 8.5 12.5 10 18.0 1.06 26 40.6 58.65 1.1 5 6.5 26.40 45.26 42.2
5011LL 4100 0.875 0.437 5.0 6.75 3.375 6.50 8.5 12.5 10 18.0 1.06 26 40.6 59.65 1.1 5 6.5 26.40 45.26 42.2
5013ST 5350 0.750 0.375 4.0 5.75 2.875 5.50 8.5 12.5 10 22.5 1.06 26 49.6 67.50 1.1 5 6.5 30.75 45.26 42.2
5013S 5350 1.000 0.500 5.5 7.75 3.875 7.50 8.5 12.5 10 22.5 1.06 26 49.6 69.50 1.1 5 6.5 30.75 45.26 42.2
5013LS 5350 0.625 0.312 4.0 5.75 2.625 5.50 8.5 12.5 10 22.5 1.06 26 49.6 67.50 1.1 5 6.5 30.75 45.26 42.2
Conduit Box Dimensions
Motors are depicted with representative conduit box. For specific dimensions or a complete motor outline drawing contact your authorized GE outlet.
Notes: 1 Shaft tolerance is +0.000 inch -0.001 inch 2 “V” represents length of straight extension of shaft 3 Tolerance on “D” dimensions will be +0.000 inches -0.060 inch 4 Dimension to AA hole
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium Voltage WP-IIAbove NEMA (2300/4000 Volts)
Dimensions
7.18
Medium
Voltage
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium VoltageAbove NEMA (2300/4000 Volts)
Standard Features
7. Data subject to change without notice. GEP-500U 01/10 www.gemotors.com
800 541 7191
Med
ium
Vol
tage
7.19
Section 7 – High HP Low and Medium VoltageGE Energy Section 7 – Medium Voltage
7.5 Data subject to change without notice. GEP-500U 01/10 www.gemotors.com 800 541 7191
Medium Voltage Pegasus™ MHV - WPII
Pricing (Please refer to your GE contact for ordering information)
Pegasus™ MHV—Weather Protected II
HP RPM Volts Frame FLA List Price Price Symbol Norm. Stk. Wt. (lbs) C Dim. (in.) Notes
800 1800 2300/4000 8210 181/104 $100,211 G8-9PWII N 7500 76.5 128, 137
800 1800 2300/4000 8210 181/104 $90,103 G8-9PWII N 7500 76.5 137
900 3600 2300/4000 8210 196/113 $118,501 G8-9PWII N 7000 65.01 128, 137
900 3600 2300/4000 8210 196/113 $108,393 G8-9PWII N 7000 65.01 137
900 1800 2300/4000 8210 201/116 $103,933 G8-9PWII N 7500 76.5 128, 137
900 1800 2300/4000 8210 201/116 $93,825 G8-9PWII N 7500 76.5 137
1000 3600 2300/4000 8212 217/125 $109,523 G8-9PWII N 8500 75.01 137
1000 1800 2300/4000 8210 221/127 $108,588 G8-9PWII N 7500 76.5 128, 137
1000 1800 2300/4000 8210 221/127 $98,482 G8-9PWII N 7500 76.5 137
1250 3600 2300/4000 8212 272/156 $112,912 G8-9PWII N 8500 75.01 137
1250 1800 2300/4000 8212 276/159 $116,039 G8-9PWII N 9200 85.5 128, 137
1250 1800 2300/4000 8212 276/159 $105,932 G8-9PWII N 9200 85.5 137
1500 3600 2300/4000 8212 334/192 $118,563 G8-9PWII N 8500 75.01 137
1500 1800 2300/4000 8212 330/189 $125,351 G8-9PWII N 9200 85.5 128, 137
1500 1800 2300/4000 8212 330/189 $115,245 G8-9PWII N 9200 85.5 137
1750 3600 2300/4000 8213 382/220 $155,397 G8-9PWII N 9300 82.5 114, 128, 137
1750 1800 2300/4000 8311 382/219 $136,806 G8-9PWII N 12000 86 128
1750 1800 2300/4000 8311 382/219 $124,678 G8-9PWII N 12000 86
2000 3600 2300/4000 8213 431/248 $161,378 G8-9PWII N 9300 82.5 114, 128, 137
2000 1800 2300/4000 8311 446/257 $143,638 G8-9PWII N 12000 86 128
2000 1800 2300/4000 8311 446/257 $131,509 G8-9PWII N 12000 86
2250 3600 2300/4000 8213 484/279 $170,017 G8-9PWII N 9300 82.5 114, 128, 137
2250 1800 2300/4000 8313 497/286 $170,425 G8-9PWII N 16000 101 128
2250 1800 2300/4000 8313 497/286 $157,398 G8-9PWII N 16000 101
2500 3600 2300/4000 8313 531/305 $203,839 G8-9PWII N 13900 95 114, 128, 137
2500 1800 2300/4000 8313 549/316 $171,892 G8-9PWII N 16000 101 128
2500 1800 2300/4000 8313 549/316 $158,866 G8-9PWII N 16000 101
2750 1800 2300/4000 8313 602/346 $177,764 G8-9PWII N 16000 101 128, 137
2750 1800 2300/4000 8313 602/346 $164,738 G8-9PWII N 16000 101 137
3000 3600 2300/4000 8313 636/366 $209,516 G8-9PWII N 13900 95 114, 128, 137
3000 1800 2300/4000 8313 656/377 $186,572 G8-9PWII N 16000 101 128, 137
3000 1800 2300/4000 8313 656/377 $173,545 G8-9PWII N 16000 101 137
3500 3600 2300/4000 8313 741/426 $220,871 G8-9PWII N 13900 95 114, 128, 137
3500 1800 2300/4000 8313 763/439 $196,847 G8-9PWII N 16000 101 128, 137
3500 1800 2300/4000 8313 763/439 $183,821 G8-9PWII N 16000 101 137
4000 3600 2300/4000 8313 847/487 $228,439 G8-9PWII N 13900 95 114, 128, 137
Notes: 114 Fabricated Copper Bar Rotor 128 Split Sleeve Bearings 137 4140 shaft material
GE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium VoltagePegasus™ MHV—WPII
Pricing (Please refer to your GE contact for ordering information)
7.20
Medium
Voltage
GE Energy Section 7 – Medium Voltage
7.6 Data subject to change without notice. GEP-500U 01/10 www.gemotors.com 800 541 7191
Medium Voltage Quantum™ LMV - TEFC
Pricing (Please refer to your GE contact for ordering information)
Quantum™ LMV - TEFC
HP RPM Volts Frame FLA List Price Price Symbol Norm. Stk. Wt. (lbs) C Dim. (in.) Notes
900 3600 2300/4000 7010 192/111 $156,830 G8-9QT N 9700 119.00 128
900 1800 2300/4000 7010 199/112 $141,244 G8-9QT N 9500 133.50 128
900 1800 2300/4000 7010 199/112 $129,520 G8-9QT N 9500 121.50
1000 3600 2300/4000 7011 212/122 $175,454 G8-9QT N 11400 119.00 128
1000 1800 2300/4000 7010 217/126 $144,827 G8-9QT N 10100 133.50 128
1000 1800 2300/4000 7010 217/126 $133,103 G8-9QT N 10100 121.50
1250 3600 2300/4000 7011 264/152 $190,720 G8-9QT N 12500 119.00 128
1250 1800 2300/4000 7010 266/154 $156,772 G8-9QT N 11000 133.50 128
1250 1800 2300/4000 7010 266/154 $145,046 G8-9QT N 11000 121.50
1350 3600 2300/4000 7011 284/164 $204,474 G8-9QT N 13000 119.00 128
1350 1800 2300/4000 7011 290/167 $165,882 G8-9QT N 12100 133.50 128
1350 1800 2300/4000 7011 290/167 $153,754 G8-9QT N 12100 121.50
1500 3600 2300/4000 7011 318/184 $205,985 G8-9QT N 13600 119.00 128
1500 1800 2300/4000 7011 320/185 $167,515 G8-9QT N 12700 133.50 128
1500 1800 2300/4000 7011 320/185 $155,792 G8-9QT N 12700 121.50
1750 1800 2300/4000 7011 375/214 $208,756 G8-9QT N 14100 133.50 114, 128, 137
1750 1800 2300/4000 7011 375/214 $197,032 G8-9QT N 14100 121.50 114, 137
2000 1800 2300/4000 7011 430/245 $221,521 G8-9QT N 15000 133.50 114, 128, 137
2000 1800 2300/4000 7011 430/245 $209,797 G8-9QT N 15000 121.50 114, 137
Notes: 114 Fabricated Copper Bar Rotor 128 Split Sleeve Bearings 137 4140 shaft material
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium VoltageQuantum™ LMV—TEFC
Pricing (Please refer to your GE contact for ordering information)
Med
ium
Vol
tage
7.21
GE Energy Section 7 – Medium Voltage
7.7 Data subject to change without notice. GEP-500U 01/10 www.gemotors.com 800 541 7191
Medium Voltage Pegasus™ MHV— TEAAC
Pricing (Please refer to your GE contact for ordering information)
Pegasus™ MHV - TEAAC
HP RPM Volts Frame FLA List Price Price Symbol Norm. Stk. Wt. (lbs) C Dim. (in.) Notes 500 3600 2300/4000 8210 110/63 $139,035 G8-9PTAC N 8100 83.26 128, 137
500 3600 2300/4000 8210 110/63 $128,927 G8-9PTAC N 8100 83.26 137
600 3600 2300/4000 8210 132/76 $140,136 G8-9PTAC N 8100 83.26 128, 137
600 3600 2300/4000 8210 132/76 $130,030 G8-9PTAC N 8100 83.26 137
600 1800 2300/4000 8208 133/76 $120,897 G8-9PTAC N 7000 90.50 128, 137
600 1800 2300/4000 8208 133/76 $110,791 G8-9PTAC N 7000 90.50
700 3600 2300/4000 8210 153/88 $141,240 G8-9PTAC N 8100 83.26 128, 137
700 3600 2300/4000 8210 153/88 $131,134 G8-9PTAC N 8100 83.26 137
700 1800 2300/4000 8210 155/89 $122,740 G8-9PTAC N 8750 101.00 128
700 1800 2300/4000 8210 155/89 $112,634 G8-9PTAC N 8750 101.00
800 3600 2300/4000 8210 175/100 $141,240 G8-9PTAC N 8100 83.26 128, 137
800 3600 2300/4000 8210 175/100 $131,134 G8-9PTAC N 8100 83.26 137
800 1800 2300/4000 8210 177/102 $124,123 G8-9PTAC N 8750 101.00 128
800 1800 2300/4000 8210 177/102 $114,017 G8-9PTAC N 8750 101.00
900 3600 2300/4000 8212 197/114 $156,830 G8-9PTAC N 9950 93.26 137
900 1800 2300/4000 8210 200/115 $141,244 G8-9PTAC N 8750 101.00 128, 137
900 1800 2300/4000 8210 200/115 $129,520 G8-9PTAC N 8750 101.00 137
1000 3600 2300/4000 8212 219/126 $175,454 G8-9PTAC N 9950 93.26 137
1000 1800 2300/4000 8212 220/126 $144,827 G8-9PTAC N 10500 101.00 128, 137
1000 1800 2300/4000 8212 220/126 $133,103 G8-9PTAC N 10500 101.00 137
1250 3600 2300/4000 8212 271/156 $190,720 G8-9PTAC N 9950 93.26 137
1250 1800 2300/4000 8212 273/157 $156,772 G8-9PTAC N 10500 101.00 128, 137
1250 1800 2300/4000 8212 273/157 $145,046 G8-9PTAC N 10500 101.00 137
1500 3600 2300/4000 8213 326/187 $205,985 G8-9PTAC N 11500 102.00 114, 128, 137
1500 1800 2300/4000 8212 326/187 $167,515 G8-9PTAC N 10500 101.00 128, 137
1500 1800 2300/4000 8212 326/187 $155,792 G8-9PTAC N 10500 101.00 137
1750 3600 2300/4000 8213 380/218 $174,407 G8-9PTAC N 11500 102.00 114, 128, 137
1750 1800 2300/4000 8311 393/226 $208,756 G8-9PTAC N 13500 112.00 128
1750 1800 2300/4000 8311 393/226 $197,032 G8-9PTAC N 13500 112.00
2000 3600 2300/4000 8213 433/249 $178,023 G8-9PTAC N 12500 102.00 114, 128, 137
2000 1800 2300/4000 8313 444/255 $221,521 G8-9PTAC N 17500 130.00 128
2000 1800 2300/4000 8313 444/255 $209,797 G8-9PTAC N 17500 130.00
2250 3600 2300/4000 8313 483/278 $218,111 G8-9PTAC N 13500 117.00 114, 128, 137
2250 1800 2300/4000 8313 500/287 $179,625 G8-9PTAC N 17500 130.00 128
2250 1800 2300/4000 8313 500/287 $166,596 G8-9PTAC N 17500 130.00
2500 3600 2300/4000 8313 535/308 $226,383 G8-9PTAC N 13500 117.00 114, 128, 137
2500 1800 2300/4000 8313 547/315 $186,974 G8-9PTAC N 17500 130.00 128
2500 1800 2300/4000 8313 547/315 $173,947 G8-9PTAC N 17500 130.00
2750 1800 2300/4000 8313 601/346 $194,323 G8-9PTAC N 17500 130.00 128, 137
2750 1800 2300/4000 8313 601/346 $181,296 G8-9PTAC N 17500 130.00 137
3000 3600 2300/4000 8313 640/368 $229,691 G8-9PTAC N 14000 117.00 114, 128, 137
3000 1800 2300/4000 8313 656/377 $201,674 G8-9PTAC N 17500 130.00 128, 137
3000 1800 2300/4000 8313 656/377 $188,647 G8-9PTAC N 17500 130.00 137
Notes: 114 Fabricated Copper Bar Rotor 128 Split Sleeve Bearings 137 4140 shaft material
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium VoltagePegasus™ MHV—TEAAC
Pricing (Please refer to your GE contact for ordering information)
7.22
Medium
Voltage
XW
V
AC
AB
XN
XL
2.20
B
BAF F
K
30 ∞
A
EE
J
D GU
C
L
XN
O
P
2.00
4.35
4.0 0
Dripproof Weather Protected II
AIR OUTLETBOTH ENDSEACH SIDE
(4)MOTORLIFTINGLUGS
AA HOLESFOR CONDUIT
KEYLENGTH
AIR INLETBOTH SIDES
.500-13,2 HOLESPROVIDED FORLIFTING TOPCOVER ONLY
REMOVABLECOVER FOR ACCESSTO FILTER(WHEN FURNISHED)
WINDINGACCESSORYLEADS BEHIN DCOVER
REAM FOR .50 DIA.DOWEL PIN ATINSTALLATION2 HOLES ON DIAGONALLYOPPOSITE FEET.
1"-11.5 NPSI2 HOLES
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
Medium VoltageAbove NEMA (2300/4000 Volts)
Dimensions
Med
ium
Vol
tage
7.23
Section 7 – High HP Low and Medium VoltageGE Energy
Data subject to change without notice. GEP-500U 01/10 • www.gemotors.com • 800-541-7191
7.24
High H
P Low &
Medium
Voltage
Notes