tco 7201 to 7221 - · pdf fileg3134 (jis g3134), grade spfh590, having all of the following:...

Tariff Description

===========================================================================

Item 50 applies unless otherwise stated.

7201.10.00 PIG IRON, comprising ALL of the following:

(a) carbon, with a composition less than 5%;

(b) sulphur;

(c) silicon;

(d) phosphorus;

(e) manganese

Op. 02.11.1999 Dec. 07.01.2000 - TC 9908323

7207.11.00 BILLETS, square, semi-finished non-alloy steel, having BOTH of

the following:

(a) thickness and width NOT less than 115 mm x 115 mm and NOT

greater than 160 mm x 160 mm;

(b) length NOT less than 11 700 mm and NOT greater than

12 200 mm

Op. 01.06.2010 Dec. 30.08.2010 - TC 1024427

7207.11.00 BILLETS, square, semi-finished non-alloy steel, having ALL of

the following:

(a) thickness and width NOT less than 130 mm X 130 mm;

(b) length NOT less than 11 800 mm and NOT greater than

12 200 mm;

(c) chemical composition by weight of ALL of the following:

(i) carbon 0.13 % - 0.17%;

(ii) manganese 0.35% - 0.55%;

(iii) sulphur 0.035 % maximum;

(iv) chromium 0.2 % maximum;

(v) copper 0.3% maximum;

(vi) phosphorous 0.035% maximum;

(vii) silicon 0.14% - 0.24%

Op. 27.06.2008 Dec. 19.09.2008 - TC 0815096

7207.19.00 STEEL BLOOMS, ROUND, NON ALLOY

Op. 02.11.2007 Dec. 30.01.2008 - TC 0718813

7207.19.00 BILLETS, leaded, hot rolled

Op. 11.09.2001 Dec. 07.12.2001 - TC 0108047

7208.25.00 SHEETS, non-alloy steel, in coils, flat rolled, hot-rolled,

uncoated, complying with Japanese Industrial Standard JIS G

3134:2006, Classification symbol SPFH590 OR Japanese Industrial

Standard JIS G 3113:2006, Classification symbol SAPH440, having

ALL of the following:

(a) yield strength NOT less than 265 MPa and NOT greater than

600 MPa;

(b) tensile strength NOT less than 440 MPa;

(c) elongation NOT less than 18% AND not greater than 46%;

(d) thickness 6.00 mm AND width 943 mm

For the purpose of this Order, tolerances allowable for

specification (d) are:

(i) thickness +/- 10%;

(ii) width +/- 1%.

Op. 19.02.2015 Dec. 11.05.2015 - TC 1507168

7208.26.00 STEEL, flat-rolled, non alloy, hot rolled, pickled, not coated,

in coils, complying with Japanese Industrial Standard G3113 (JIS

G3113), grade SAPH440, having ALL of the following:

(a) yield strength NOT less than 305 MPa;


(c) elongation NOT less than 29%;

(d) in ANY of the following sizes:

(i) thickness 3.40 mm and width 985 mm;

(ii) thickness 3.50 mm and width 805 mm;

(iii) thickness 4.00 mm and width 1 210 mm

Tariff Description

===========================================================================


For the purposes of this Order, tolerances allowable for


(a) thickness +/- 10%

(b) width +/- 1%

Op. 04.04.2013 Dec. 24.06.2013 - TC 1311719

7208.26.00 STEEL, flat rolled, non-alloy, hot rolled, pickled, not coated,


G3131), grades SPHD OR SPHE, having ALL of the following:

(a) tensile strength NOT less than 270 MPa;

(b) elongation NOT less than 32%;

(c) in ANY of the following sizes:


(ii) thickness 3.00 mm and width 1 119 mm;

(iii) thickness 3.50 mm and width 1 145 mm;

(iv) thickness 4.00 mm and width 875 mm;

(v) thickness 4.00 mm and width 970 mm;

(vi) thickness 4.00 mm and width 1 070 mm


specification (c) are:


(b) width +/- 1%

Op. 04.04.2013 Dec. 24.06.2013 - TC 1311527

7208.26.00 STEEL, flat rolled, iron OR non alloy, hot rolled, pickled, not

coated, in coils, complying with Japanese Industrial Standard

G3131 (JIS G3131), grades SPHC OR SPHD, having ALL of the

following:


325 MPa;


(c) elongation NOT less than 35% and NOT greater than

53%;

(d) thickness 3.20 mm and width 1 130 mm




(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308144

7208.26.00 STEEL, flat rolled, iron OR non-alloy, hot rolled, pickled, not


G3134 (JIS G3134) grade SPFH590 OR Japanese Industrial Standard

G3113 (JIS G3113) grade SAPH440, having ALL of the following:


600 MPa;



46%;

(d) thickness 3.20 mm and width 950 mm




(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308136

Tariff Description

===========================================================================


7208.26.00 STEEL, flat rolled, iron OR non-alloy steel, hot rolled,

pickled, not coated, in coils, complying with Japanese

Industrial Standard G3134 (JIS G3134) grade SPFH590 OR Japanese

Industrial Standard G3113 (JIS G3113) grade SAPH440, having ALL

of the following:


600 MPa;


(c) total elongation NOT less than 18% and NOT greater than

46%;

(d) in EITHER of the following sizes:

(i) thickness 3.20 mm and width 1 034 mm;

(ii) thickness 3.20 mm and width 1 350 mm




(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349335



G3134 (JIS G3134), grade SPFH590, having ALL of the following:


610 MPa;


(c) elongation NOT less than 17% and NOT greater than 31%;





(b) width +/- 1%

Op. 17.04.2014 Dec. 14.07.2014 - TC 1413447



G3113), grade SAPH440, having ALL of the following:







(iii) thickness 1.60 mm and width 762 mm;



(vi) thickness 1.60 mm and width 825 mm;

(vii) thickness 1.60 mm and width 860 mm;

(viii) thickness 1.60 mm and width 930 mm;

(ix) thickness 1.60 mm and width 1 009 mm;

(x) thickness 1.60 mm and width 1 058 mm;

(xi) thickness 1.70 mm and width 950 mm;

(xii) thickness 1.70 mm and width 959 mm;

(xiii) thickness 1.95 mm and width 950 mm;

(xiv) thickness 1.95 mm and width 1 185 mm;

(xv) thickness 2.00 mm and width 760 mm;

(xvi) thickness 2.00 mm and width 766 mm;

(xvii) thickness 2.00 mm and width 860 mm;

(xviii) thickness 2.00 mm and width 955 mm;

(xix) thickness 2.00 mm and width 1 090 mm;

(xx) thickness 2.50 mm and width 1 135 mm

Tariff Description

===========================================================================





(b) width +/- 1%

Op. 04.04.2013 Dec. 24.06.2013 - TC 1311717













vii) thickness 1.60 mm and width 1 030 mm;

(viii) thickness 1.60 mm and width 1 035 mm;



(xi) thickness 1.80 mm and width 1 000 mm;



(xiv) thickness 1.90 mm and width 825 mm;




(xviii) thickness 1.90 mm and width 1 010 mm;


(xx) thickness 1.90 mm and width 1 050 mm;

(xxi) thickness 1.90 mm and width 1 060 mm;

(xxii) thickness 1.90 mm and width 1 110 mm;

(xxiii) thickness 1.90 mm and width 1 125 mm;

(xxiv) thickness 1.90 mm and width 1 190 mm;

(xxv) thickness 2.00 mm and width 607 mm;

(xxvi) thickness 2.00 mm and width 1 024 mm;

(xxvii) thickness 2.00 mm and width 1 140 mm;

(xxviii) thickness 2.00 mm and width 1 210 mm;

(xxix) thickness 2.20 mm and width 785 mm;

(xxx) thickness 2.20 mm and width 970 mm;

(xxxi) thickness 2.20 mm and width 1 155 mm;

(xxxii) thickness 2.20 mm and width 1 175 mm;

(xxxiii) thickness 2.50 mm and width 1 020 mm;

(xxxiv) thickness 2.50 mm and width 1 160 mm




(b) width +/- 1%

Op. 04.04.2013 Dec. 24.06.2013 - TC 1311524



G3131 (JIS G3131), grades SPHC OR SPHD OR SPHE, having ALL of

the following:


(b) total elongation NOT less than 27%;




Tariff Description

===========================================================================




(v) thickness 1.40 mm and width 1 050 mm;

(vi) thickness 1.40 mm and width 1 080 mm;

(vii) thickness 1.40 mm and width 1 150 mm;





(xii) thickness 1.90 mm and width 1 360 mm




(b) width +/- 1%

Op. 14.03.2013 Dec. 03.06.2013 - TC 1309208

7208.27.00 STEEL, flat rolled, iron OR non alloy, hot rolled, pickled, not


G3131 (JIS G3131), grades SPHC OR SPHD, having ALL of the

following:


325 MPa;



53%;





(iv) thickness 2.90 mm and width 1 200 mm




(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308076



Industrial Standard G3131 (JIS G3131), grades SPHC OR SPHD,

having ALL of the following:


325 MPa;



53%;









(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349331



Tariff Description

===========================================================================


Industrial Standard G3134 (JIS G3134) grade SPFH590 OR Japanese

Industrial Standard G3113 (JIS G3133) grade SAPH440, having ALL

of the following:


600 MPa;



46%;









(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349332

7208.52.00 STEEL PLATE, hot rolled, non-alloy, conforming to Japanese

Industrial Standard G3106, (JIS G3106), grade SM400A, having


(a) hydrochloric acid (HCl) corrosion rate NOT greater than 1

mg/cm2/h, with HCI concentration of 20% at 40 degrees

Celsius;

(b) sulphuric acid (H2S04) corrosion rate NOT greater than

150g/M2/h, with H2S04 concentration of 50% at 70 degrees

Celsius;

(c) thickness NOT less than 4.75 mm and NOT greater than 10 mm;

(d) tensile strength NOT less than 400 Mpa and NOT greater

than 510 Mpa;

(e) yield strength NOT less than 245 Mpa and NOT greater than

400 Mpa;

(f) chemical composition by weight of ALL of the following:

(i) carbon content NOT greater than 0.14%;

(ii) silicon content NOT greater than 0.55%;

(iii) magnesium content NOT greater than 1.60%;

(iv) phosphorus content NOT greater than 0.025%;

(v) sulphur content NOT greater than 0.025%;

(vi) copper content NOT less than 0.25% and NOT greater

than 0.4%;

(vii) antimony content NOT less than 0.01% and NOT greater

than 0.1%;

(viii) NOT greater than 0.08% of any other alloying element

if present

Op. 23.04.2014 Dec. 21.07.2014 - TC 1413674

7209.16.00 STEEL, flat rolled, non-alloy, cold rolled, not coated,

in coils, having ALL of the following:

(a) yield strength NOT greater than 250 MPa;








(v) thickness 1.15 mm and width 1 089mm;





Tariff Description

===========================================================================




(xii) thickness 1.35 mm and width 1 185 mm;

(xiii) thickness 1.35 mm and width 1 525 mm;





(xviii) thickness 1.55 mm and width 801 mm;


(xx) thickness 1.60 mm and width 790 mm;


(xxii) thickness 1.80 mm and width 910 mm;



(xxv) thickness 1.80 mm and width 1 135 mm;

(xxvi) thickness 1.95 mm and width 770 mm;

(xxvii) thickness 1.95 mm and width 1 200 mm




(b) width +/- 1%

Op. 09.04.2013 Dec. 24.06.2013 - TC 1312160










(b) width +/- 1%

Op. 27.03.2013 Dec. 17.06.2013 - TC 1310748

7209.16.00 STEEL, flat rolled, iron OR non-alloy, cold rolled, not


G3141 (JIS G3141) grades SPCC OR SPCD OR SPCE, having ALL of the

following:


265 MPa;



57%;




(iii) thickness 2.00 mm and width 620 mm




(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308126

7209.16.00 STEEL, flat rolled, iron OR non-alloy steel, cold rolled, in

coils, not coated, complying with Japanese Industrial Standard

G3135 (JIS G3135), grade SPFC440 OR SPFC590, having ALL of the

Tariff Description

===========================================================================


following:


560 MPa;


(c) total elongation NOT less than 18%;














(xiii) thickness 2.00 mm and width 990 mm




(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349343

7209.17.00 STEEL, flat rolled, iron OR non-alloy steel, cold rolled, not


G3135 (JIS G3135), grades SPFC440 OR SPFC590, having ALL of the

following:


560 MPa;









(b) width +/- 1%

Op. 05.09.2013 Dec. 02.12.2013 - TC 1330121



















Tariff Description

===========================================================================




(xv) thickness 0.75 mm and width 1 220 mm;

(xvi) thickness 0.75 mm and width 1 370 mm;

(xvii) thickness 0.75 mm and width 1 410 mm;







(xxiv) thickness 0.76 mm and width 660 mm;

(xxv) thickness 0.76 mm and width 675 mm;



(xxviii) thickness 0.76 mm and width 1 420 mm;

(xxix) thickness 0.80 mm and width 600 mm;

(xxx) thickness 0.80 mm and width 620 mm;

(xxxi) thickness 0.80 mm and width 660 mm;

(xxxii) thickness 0.80 mm and width 785 mm;

(xxxiii) thickness 0.80 mm and width 850 mm;

(xxxiv) thickness 0.80 mm and width 900 mm;

(xxxv) thickness 0.80 mm and width 1 010 mm;

(xxxvi) thickness 0.80 mm and width 1 140 mm;

(xxxvii) thickness 0.80 mm and width 1 220 mm;

(xxxviii) thickness 0.80 mm and width 1 270 mm;

(xxxix) thickness 0.80 mm and width 1 570 mm;

(xl) thickness 0.80 mm and width 1 584 mm;

(xli) thickness 0.85 mm and width 995 mm;

(xlii) thickness 0.85 mm and width 1 140 mm;

(xliii) thickness 0.85 mm and width 1 300 mm;

(xliv) thickness 0.85 mm and width 1 484 mm;

(xlv) thickness 0.90 mm and width 1 060 mm;

(xlvi) thickness 0.95 mm and width 820 mm;

(xlvii) thickness 0.95 mm and width 930 mm;

(xlviii) thickness 0.95 mm and width 990 mm;

(xlix) thickness 0.95 mm and width 1 100 mm;

(l) thickness 0.95 mm and width 1 105 mm;

(li) thickness 0.95 mm and width 1 130 mm;

(lii) thickness 0.95 mm and width 1 170 mm;

(liii) thickness 0.95 mm and width 1 290 mm;

(liv) thickness 0.95 mm and width 1 302 mm;

(lv) thickness 0.95 mm and width 1 770 mm;

(lvi) thickness 1.00 mm and width 765 mm




(b) width +/- 1%

Op. 09.04.2013 Dec. 24.06.2013 - TC 1312159

7209.17.00 STEEL, flat rolled, non-alloy, cold rolled, not

coated, in coils, having ALL of the following:








(iv) thickness 0.65 mm and width 1 560 mm;



Tariff Description

===========================================================================



(viii) thickness 1.00 mm and width 1 588 mm




(b) width +/- 1%

Op. 27.03.2013 Dec. 17.06.2013 - TC 1310743

7209.17.00 STEEL, flat rolled, iron OR non-alloy, cold rolled, not coated,


G3141) grades SPCC OR SPCD OR SPCE, having ALL of the following:


265 MPa;



57%;







(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308130


coated, in coils, having ALL of the following;

















(xiii) thickness 0.85 mm and width 1 730 mm




(b) width +/- 1%

Op. 24.12.2012 Dec. 18.03.2013 - TC 1248927










Tariff Description

===========================================================================
















(xviii) thickness 0.80 mm and width 1 585 mm




(b) width +/- 1%

Op. 24.12.2012 Dec. 18.03.2013 - TC 1248928



G3141 (JIS G3141) grades SPCC, SPCD OR SPCE having ALL of the

following:


265 MPa;



57%;









(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349338

7209.17.00 STEEL, flat rolled, iron OR non-alloy steel, cold rolled,

not coated, in coils, complying with Japanese Industrial

Standard G3135 (JIS G3135), grades SPFC440, OR SPFC590, having



560 MPa;









specification (D) are:


(b) width +/- 1%

Tariff Description

===========================================================================


Op. 28.12.2012 Dec. 18.03.2013 - TC 1349341

7209.18.00 STEEL, flat rolled, non-alloy, cold rolled, not coated, in

coils, complying with Japanese Industrial Standard G3141 (JIS

G3141), grades SPCC, SPCD OR SPCE, having ALL of the

following:


265 MPa;



(d) thickness 0.45 mm and width 710 mm




(b) width +/- 1%

Op. 06.09.2013 Dec. 02.12.2013 - TC 1330277



G3141 (JIS G3141) grades SPCC, SPCD OR SPCE, having ALL of the

following:


265 MPa;



57%;



(ii) thickness 0.40 mm and width 960 mm




(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349336

7210.30.00 STEEL, flat rolled, non-alloy, electrolytically plated OR coated

with zinc, in coils, having ALL of the following:


240 MPa;



(d) coating mass NOT less than 36 g/m2 and NOT greater than

90 g/m2 on each side;

(e) in ANY of the following sizes:










(x) thickness 0.90 mm and width 950 mm


specification (e) are:


(b) width +/- 1%

Tariff Description

===========================================================================


Op. 22.05.2013 Dec. 12.08.2013 - TC 1316842

7210.30.00 STEEL, flat rolled, non-alloy, electrolytically plated or

coated with zinc, in coils, having ALL of the following:


210 MPa;

(b) tensile strength NOT less than 270 MPa and NOT greater

than 350 MPa;


(d) total coating mass NOT less than 47 g/m2 and NOT greater

than 61 g/m2 on each side;

(e) thickness 0.70 mm and width 1 160 mm




(b) width +/- 1%

Op. 13.03.2013 Dec. 03.06.2013 - TC 1309163

7210.30.00 STEEL, flat rolled, iron OR non-alloy steel, tin AND zinc alloy

electrolytically coated, in coils, having ALL of the

following:


370 MPa;





(e) thickness 0.40 mm and width 970 mm




(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349355

7210.30.00 STEEL, flat rolled, iron OR non-alloy steel, tin AND zinc alloy

electrolytically coated, in coils, having ALL of the

following:


370 MPa;












(vii) thickness 1.00 mm and width 865 mm




(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349357

7210.30.00 STEEL, flat rolled non-alloy, electrolytically coated with zinc,

Tariff Description

===========================================================================


having ALL of the following features;

(a) a thickness of 2.39mm or more;

(b) a width NOT less than 1219mm and NOT greater than 1249 mm;

(b) to specification JIS G3313 SECC or SEHC

Op. 01.07.1996 Dec. 21.06.1996 - TC 9607869

7210.49.00 STEEL COILS, hot dipped zinc-aluminium-magnesium alloy coated,



520 MPa;


than 590 MPa;


(d) total coating mass NOT less than 150 g/m2;

(e) total coated thickness NOT less than 3.70 mm;

(f) coil width NOT less than 800 mm and NOT greater than

1 400 mm;

(g) coated with a zinc-aluminium-magnesium alloy, having a

composition by weight of:

(i) NOT less than 2% and NOT greater than 4% magnesium;

(ii) NOT less than 3% and NOT greater than 5% aluminium;

(iii) less than 1% of minor additions;

(iv) balance zinc

Op. 20.07.2016 Dec. 10.10.2016 - TC 1635417

7210.49.00 STEEL, flat rolled, non-alloy, hot dipped galvannealed zinc


(a) yield strength, NOT less than 195 MPa and NOT greater than

295 MPa;



(d) coating mass NOT less than 35 g/m2 and NOT greater than 65

g/m2;

(e) thickness 0.70 mm AND width 1 660 mm


specification (e) are as follows:

(i) thickness + OR - 10%;

(ii) width + OR - 1%

Op. 02.05.2016 Dec. 20.07.2016 - TC 1615482



(a) yield strength NOT less than 135 MPa and NOT greater

than 225 MPa;


(c) elongation NOT less than 40% AND not greater than 50%;

(d) coating mass NOT less than 35 g/m2 and NOT greater

than 65 g/m2;






(v) thickness 0.70 mm and width 1 170 mm

For the purposes of this order, tolerances allowable for



(b) width +/- 1%

Op. 07.10.2014 Dec. 09.02.2015 - TC 1435159

7210.49.00 STEEL, flat rolled, non-alloy steel, hot dipped galvannealed

Tariff Description

===========================================================================


zinc coated, in coils, having ALL of the following:


295 MPa;




than 65 g/m2;

(e) in EITHER of the following sizes:

(i) thickness 0.70 mm AND width 818 mm;

(ii) thickness 0.70 mm and width 855 mm




(b) width +/- 1%

Op. 07.10.2014 Dec. 30.12.2014 - TC 1435154

7210.49.00 STEEL, flat rolled, non-alloy, hot dipped galvannealed



225 MPa;



50%;


than 65 g/m2;





(b) width +/- 1%

Op. 06.11.2014 Dec. 28.01.2015 - TC 1438583

7210.49.00 STEEL, flat rolled, non-alloy, hot-dipped galvannealed zinc



380 MPa;



(d) coating mass NOT less than 35 g/M2 and NOT greater than

65 g/M2 on each side;


(i) thickness 1.20 mm and width 908 mm





(b) width +/- 1%

Op. 07.11.2014 Dec. 28.01.2015 - TC 1438838

7210.49.00 STEEL, flat rolled, non-alloy, hot-dipped galvannealed zinc



225 MPa;



(d) coating mass NOT less than 35 g/M2 and NOT greater than

65 g/M2 on each side;


(i) thickness 0.55 mm and width 1 127 mm



Tariff Description

===========================================================================






(b) width +/- 1%

Op. 13.11.2014 Dec. 02.02.2015 - TC 1440014






(d) coating mass NOT less than 30 g/m2 on each side;

(e) thickness 0.70 mm;

(f) width NOT less than 1 480 mm and NOT greater than 1 570 mm

For the purposes of this order, tolerance allowable for

specification (e) are +/- 10%

Op. 14.04.2014 Dec. 14.07.2014 - TC 1412844

7210.49.00 STEEL, flat rolled, non-alloy, hot dipped zinc coated, in coils,



300 MPa;





(e) thickness 0.65 mm;

(f) width NOT less than 1 455 mm and NOT greater than 1 545 mm

For the purposes of this order, tolerance allowable for

specification (e) are +/- 10%;

Op. 14.04.2014 Dec. 14.07.2014 - TC 1412845

7210.49.00 COILS, non-alloy steel, flat-rolled, hot dipped galvannealed

zinc coated, having ALL of the following:




(d) coating mass NOT less than 30 g/m2 on each side;





(ii) width +/- 1%

Op. 05.02.2014 Dec. 23.04.2014 - TC 1404843

7210.49.00 COILS, non-alloy steel, flat-rolled, hot dipped zinc coated,



300 MPa;









(ii) width +/- 1%

Tariff Description

===========================================================================


Op. 05.02.2014 Dec. 23.04.2014 - TC 1404844




325 MPa;




65 g/m2 each side;





(b) width +/- 1%

Op. 17.12.2013 Dec. 12.03.2014 - TC 1341633




400 MPa;




than 65 g/m2 each side;





(b) width +/- 1%

Op. 17.12.2013 Dec. 12.03.2014 - TC 1341634




420 MPa;









(b) width +/- 1%

Op. 23.12.2013 Dec. 17.03.2014 - TC 1342242

7210.49.00 COILS, non-alloy steel, hot rolled, zinc coated, complying with

American Society for Testing and Materials Standard A653/A653M-

11 (ASTM A653/A653M-11), having ALL of the following:

(a) thickness NOT less than 2.75 mm and NOT greater than

6.0 mm;

(b) width NOT less than 784 mm and NOT greater than

1 263 mm;

(c) minimum yield strength NOT less than 330 Mpa;

(d) minimum tensile strength NOT less than 430 Mpa;

(e) inside diameter NOT less than 711 mm and NOT greater

than 813 mm;

Tariff Description

===========================================================================


(f) zinc coating mass NOT less than 0.080 kg/m2 per side;

(g) weight NOT less than 14 metric tonnes;

(h) chemical composition by weight of ALL of the following:


(ii) manganese content NOT less than 0.30% and NOT

greater than 0.90%;

(iii) phosphorus content NOT greater than 0.03%;

(iv) sulphur content NOT greater than 0.03%;

(v) chromium content less than 0.30%;

(vi) molybdenum content less than 0.08%;

(vii) aluminium content NOT greater than 0.10%;

(viii) copper content NOT greater than 0.25%;

(ix) nickel content NOT greater than 0.25%;

(x) titanium content NOT greater than 0.04%;

(xi) vanadium content less than 0.10%;

(xii) silicon content NOT greater than 0.45%

Op. 20.08.2013 Dec. 09.12.2013 - TC 1328432






(d) coating mass on each side NOT less than 30 g/m2 and NOT

greater than 70 g/m2;





(b) width +/- 1%

Op. 06.09.2013 Dec. 02.12.2013 - TC 1330458




305 MPa;









(b) width +/- 1%

Op. 06.09.2013 Dec. 02.12.2013 - TC 1330276

7210.49.00 STEEL, flat rolled, non-alloy, hot dipped galvannealed, zinc


(a) yield strength NOT less than 120 MPa and NOT greater

than 180 MPa;


than 350 MPa;







Tariff Description

===========================================================================





(b) width +/- 1%

Op. 04.06.2013 Dec. 21.10.2013 - TC 1318527




400 MPa;









(b) width +/- 1%

Op. 29.05.2013 Dec. 19.08.2013 - TC 1317486




280 MPa;

































(xxviii) thickness 0.80 mm and width 680 mm;

(xxix) thickness 0.80 mm and width 1 185 mm;

(xxx) thickness 0.80 mm and width 1 300 mm;

(xxxi) thickness 0.80 mm and width 1 370 mm;

Tariff Description

===========================================================================


(xxxii) thickness 0.80 mm and width 1 325 mm;

(xxxiii) thickness 0.80 mm and width 1 545 mm;

(xxxiv) thickness 0.80 mm and width 1 600 mm;

(xxxv) thickness 0.80 mm and width 1 695 mm;

(xxxvi) thickness 0.80 mm and width 1 760 mm;

(xxxvii) thickness 0.80 mm and width 1 840 mm;

(xxxviii) thickness 0.90 mm and width 950 mm;

(xxxix) thickness 0.90 mm and width 1 530 mm;

(xl) thickness 0.90 mm and width 1 800 mm;

(xli) thickness 1.20 mm and width 1 730 mm;

(xlii) thickness 1 20 mm and width 1 770 mm




(b) width +/- 1%

Op. 22.05.2013 Dec. 12.08.2013 - TC 1316841















(vii) thickness 1.20 mm and width 955 mm




(b) width +/- 1%

Op. 09.04.2013 Dec. 24.06.2013 - TC 1312163












(iv) thickness 2.20 mm and width 910 mm




(b) width +/- 1%

Op. 27.03.2013 Dec. 17.06.2013 - TC 1310746



Tariff Description

===========================================================================



180 MPa;


than 350 MPa;







(b) width +/- 1%

Op. 13.03.2013 Dec. 03.06.2013 - TC 1309160




295 MPa;









(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308125




325 MPa;



50%;












(ix) thickness 2.00 mm and width 1 070 mm




(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308121




400 MPa;


Tariff Description

===========================================================================


























(xxi) thickness 2.00 mm and width 1 310 mm




(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308073




305 MPa;



57%;

















(xiv) thickness 1.40 mm and width 933 mm



(xvii) thickness 1.80 mm and width 1 022 mm



Tariff Description

===========================================================================



(b) width +/- 1

Op. 04.03.2013 Dec. 13.05.2013 - TC 1308115








(e) in EITHER of the following sizes:






(b) width +/- 1%

Op. 04.03.2013 Dec. 13.05.2013 - TC 1307948

7210.49.00 STEEL, flat rolled non-alloy, hot dipped galvannealed zinc



380 MPa;


(c) elongation NOT less than 30%.







(b) width +/- 1%

Op. 04.02.2013 Dec. 02.05.2013 - TC 1304297

















(ix) thickness 0.95 mm and width 820 mm;





(b) width +/- 1%

Op. 24.12.2012 Dec. 18.03.2013 - TC 1248929

Tariff Description

===========================================================================


























(xvii) thickness 1.00 mm and width 1 160 mm




(b) width +/- 1%

Op. 24.12.2012 Dec. 18.03.2013 - TC 1248930



(a) yield strength NOT less than 165 MPa and NOT

greater than 325 MPa;


(c) total elongation NOT less than 35% and NOT

greater than 50%;

(d) total coating mass NOT less than 45 g/m2 and NOT

greater than 65 g/m2 on each side;





(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349350




305 MPa;


(c) total elongation NOT less than 37% and NOT greater

than 57%;






Tariff Description

===========================================================================

























(xxvi) thickness 2.30 mm and width 985 mm




(b) width +/- 1

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349351



(a) yield strength NOT less than 155 MPa and NOT

greater than 295 MPa;



(d) total coating mass NOT less than 35 g/m2 and NOT

greater than 65 g/m2 on each side;













(xii) thickness 1.60 mm and width 1 160 mm




(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349352




Tariff Description

===========================================================================


400 MPa;










(v) thickness 2.60 mm and width 1 230 mm




(b) width +/- 1%

Op. 28.12.2012 Dec. 18.03.2013 - TC 1349354

7210.49.00 COILS, non-alloy steel, hot rolled, zinc coated, complying with

American Society for Testing and Materials Standard ASTM A 653/A

653M - 05a, having ALL of the following:

(a) coil thickness NOT less than 3.5 mm and NOT greater than

6.0 mm;

(b) coil width NOT less than 784 mm and NOT greater than

1 263 mm;



(e) coil inside diameter NOT less than 711 mm and NOT

greater than 813 mm;

(f) zinc coating mass NOT less than 0.080 kg/m2 per side;

(g) each coil weighing NOT less than 14 metric tonnes;

(h) chemical composition by weight of ALL of the following:


(ii) manganese content NOT less than 0.30% and NOT

greater than 0.90%;



(v) chromium content less than 0.30%;

(vi) molybdenum content less than 0.08%;

(vii) aluminium content NOT greater than 0.10%;

(viii) copper content NOT greater than 0.25%;

(ix) nickel content NOT greater than 0.25%;

(x) titanium content NOT greater than 0.04%;

(xi) vanadium content less than 0.10%;

(xii) silicon content NOT greater than 0.45%

Op. 09.11.2012 Dec. 04.02.2013 - TC 1242989

7210.50.00 TIN FREE STEEL, flat rolled, in coils, chromium plated, having


(a) width NOT less than 750 mm and NOT greater than 1 000 mm;

(b) thickness NOT greater 0.30 mm;

(c) temper designation of 61 to 76 (both inclusive) in

accordance with Rockwell hardness 30 T range

Op. 26.11.2009 Dec. 26.02.2010 - TC 0944971

7210.69.00 STEEL, flat rolled, non-alloy, aluminium coated, in coils,

having BOTH of the following:

(a) thickness 0.3 mm;

(b) width of 640 mm

For the purpose of this order, tolerances allowable for

specification are:

Tariff Description

===========================================================================



(b) width +/- 10%

Op. 16.12.2014 Dec. 09.03.2015 - TC 1443915

7210.69.00 STEEL COILS OR SHEETS, aluminium silicon alloy coated,

conforming to European Standard 10346:2009(E) (EN 10346:2009

(E)), having ALL of the following:

(a) qualities - having ANY of the following:

(i) bending and profiling conforming to DX51D+AS;

(ii) drawing conforming to DX52D+AS;

(iii) deep drawing conforming to DX53D+AS;

(iv) special deep drawing conforming to DX54D+AS,

(b) coating weights conforming to EITHER of the following:

(i) AS80;

(ii) AS120

(c) coating consisting of NOT less than 88% aluminium and

balance silicon;

(d) in any of the following sizes:











For the purposes of this order tolerances allowable on widths

and thicknesses are:

(a) widths +6 mm / - 0 mm;

(b) thicknesses + or - 0.2 mm

Op. 30.09.2014 Dec. 05.02.2015 - TC 1434267

7210.69.00 STEEL SHEET, ALUMINIUM SILICON ALLOY COATED, whether or not in

coil, having ALL of the following:

(a) width 630 mm, 699 mm, 780 mm, 790 mm, 810 mm, 900 mm,

914 mm, 930 mm, 990 mm, 1 000 mm, 1 025 mm, 1 030 mm,

1 035 mm, 1 100 mm, 1 120 mm, 1 146 mm, 1 160 mm,

1 165 mm, 1 170 mm, 1 200 mm, 1 219 mm, 1 220 mm, 1 250 mm;

(b) thickness 0.55 mm, 0.60 mm, 0.72 mm, 0.75 mm, 0.80 mm,

0.90mm, 0.96 mm, 1.00 mm, 1.15 mm, 1.20 mm, 1.50 mm,

1.55 mm, 1.60 mm, 1.90 mm or 2.00 mm;

(c) coating consisting of NOT less than 88% aluminium and

balance silicon;

(d) coating weight NOT less than 20 gsm and NOT greater than

90 gsm;

(e) conforming to EITHER of the following:

(i) American Society of Testing and Materials

Standards A 463, having ANY combination of the

following:

(i) coating symbol T1-25 or T1-40;

(ii) quality CS or FS or DDS or EDDS;

(ii) Japanese Industrial Standard JIS G 3314, having ANY

combination of the following:

(i) coating symbol 40 or 60 or 80;

(ii) quality SA1C or SA1D or SA1E

For the purposes of this order tolerances allowable on widths

and thicknesses are:

(a) widths + or - 2 mm;

(b) thicknesses + or - 0.2 mm

Op. 19.11.2009 Dec. 05.02.2010 - TC 0943744

Tariff Description

===========================================================================


7210.69.00 SHEET, STEEL, aluminium coated to American Society

of Testing and Materials A 463 (ASTM A 463) having ANY

combination of the following:

(a) coating:

(i) T1-25;

(ii) T1 - 40

(b) quality:

(i) CS;

(ii) DDS

Op. 07.07.2008 Dec. 26.09.2008 - TC 0816281

7210.69.00 STEEL, aluminium coated, flat rolled, coil, conforming to ASTM A463

OR JIS G 3314, chromated OR non chromated, having ANY combination

of the following characteristics:

(a) coating:

(i) T125;

(ii) T140;

(b) quality:

(i) CQ;

(ii) DQ;

(iii) DDQ

Op. 10.11.1997 Dec. 16.01.1998 - TC 9709961

7210.70.00 SHEETS, non-alloy steel, hot dipped zinc coated, high polymer

prepainted, having ALL of the following:


440 MPa;


than 550 MPa;


(d) zinc coating density NOT less than 120 g/m2;

(e) one side surface colour painted EITHER white OR grey;

(f) polyurethane adhering coating;

(g) prepainted steel with a specular gloss level at 60

degrees NOT less than 40 units and NOT more than 95 units

as defined by Australian Standard/New Zealand Standard

AS/NZS 1580.602.2:1995;

(h) sheet thickness of 0.35 mm OR 0.40 mm OR 0.45 mm, having

ANY of the following:

(i) width 708 mm AND length 548 mm OR 708 mm OR

988 mm;

(ii) width 660 mm AND length 3 600 mm OR 3 740 mm

OR 3 875mm OR 3 940 mm OR 4 035 mm;

(iii) width 710 mm AND length 4 281 mm OR 4 383 mm;

(iv) width 722 mm AND length 3 785 mm OR 3 875 mm

OR 3 985 mm OR 4 035 mm OR 4 135 mm;

(v) width 800 mm AND length 1 437 mm;

(vi) width 700 mm AND length 1 357 mm OR 1 437 mm;

(vii) width 883 mm AND length 1 253 mm OR 1 682 mm OR

2 338 mm OR 2 658 mm OR 3 218 mm OR 3 938mm OR

4 798 mm,


specification (h) are ANY of the following:

(a) width +2 mm;

(b) length +4 mm;

(c) thickness + OR - 0.03 mm

Op. 13.11.2013 Dec. 03.03.2014 - TC 1338556

7210.70.00 COILS, non-alloy steel, prepainted, hot dipped zinc coated,



440 MPa;

Tariff Description

===========================================================================



than 550 MPa;





(g) prepainted steel with a specular gloss level at 60

degrees NOT less than 40 units and NOT more than 95 units

as defined by Australian Standard/New Zealand Standard

AS/NZS 1580.602.2:1995;

(h) width 605 mm OR 780 mm;

(i) thickness 0.35 mm OR 0.40 mm OR 0.45 mm OR 0.5 mm,


specification (h) and (i) are EITHER of the following:

(i) width + 3 mm;

(ii) thickness + OR - 0.3 mm

Op. 14.11.2013 Dec. 10.02.2014 - TC 1338606

7210.70.00 SHEETS, non-alloy steel, hot dipped zinc coated, high polymer

prepainted, having ALL of the following:


360 MPa;


than 400 MPa;


(d) zinc coating density NOT less than 120g/m2;

(e) one side surface colour painted white OR silver OR

grey;

(f) epoxy coating;

(g) sheet thickness of 0.45 mm OR 0.50 mm, having ANY of the

following:

(i) width 607 mm AND length 1 725 mm;

(ii) width 672 mm AND length 1 725 mm OR 1 800mm;

(iii) width 729 mm AND length 1 520mm OR 1 570mm OR

1 680 mm;

(iv) width 774 mm AND length 1 580 mm OR 1 680 mm OR

1 725 mm;

(v) width 824 mm AND length 1 540 mm OR 1 610 mm OR

1 680 mm;

(vi) width 924 mm AND length 1 610 mm OR 1 670 mm OR

1 800 mm OR 2 030 mm;

(vii) width 952 mm AND length 666 mm;

(viii) width 1032 mm AND length 570 mm,


specification (g) are ANY of the following:

(a) width +2 mm;

(b) length +2 mm;

(c) thickness + OR - 0.03 mm

Op. 13.11.2013 Dec. 10.02.2014 - TC 1338558

7210.70.00 SHEET, COMPOSITE, galvanized steel laminated with polyvinyl

chloride, having BOTH of the following:

(a) steel thickness NOT less than 0.6 mm;

(b) polyvinyl chloride laminate thickness NOT less than

0.8 mm

Op. 01.08.2005 Dec. 21.10.2005 - TC 0510003

7210.90 PLATES OR SHEETS, steel, clad with titanium

Op. 30.04.1987 Dec. 24.09.1987 - TC 8733390

7210.90.00 CERAMIC STEEL, being two layers of enamel fused onto high grade

steel

Tariff Description

===========================================================================


Op. 14.11.1994 Dec. 07.03.1995 - TC 9408919

7211.13.00 FLAT BAR, alloyed steel, hot rolled, having ALL of the following:

(a) thickness of 14 mm;

(b) width NOT less than 200 mm and NOT greater than 300 mm;



(e) minimum elongation greater than 17%;

(f) rolled edge condition;

(g) chemical composition by weight of ALL of the following:


(ii) manganese content greater than 1.20% and NOT

greater than 1.64%;



(v) silicon content NOT greater than 0.55%

For the purposes of this order, tolerances allowable for (a) are

+/- 10%

Op. 11.11.2014 Dec. 28.01.2015 - TC 1439186












(vi) thickness 3.00 mm and width 370 mm




(b) width +/- 1%

Op. 04.04.2013 Dec. 24.06.2013 - TC 1311529

7211.23 HOOP AND STRIP, hardened and tempered

Op. 01.07.1996 Dec. 01.07.1996 - TC 9606782















(ix) thickness 1.60 mm and width 310 mm




Tariff Description

===========================================================================


(b) width +/- 1%

Op. 09.04.2013 Dec. 24.06.2013 - TC 1312161


Op. 01.07.1996 Dec. 11.06.1996 - TC 9605659

7211.29.00 STRIP, steel, annealed, cold rolled, in coil form, having ALL

of the following:

(a) carbon weight composition NOT less than 0.55% and NOT

greater than 0.79%;

(b) strip width NOT less than 7.7 mm and NOT greater

than 599 mm;

(c) strip thickness NOT less than 0.70 mm and NOT greater

than 1.00 mm

Op. 07.07.2010 Dec. 06.10.2010 - TC 1030736


Op. 01.01.1988 Dec. 01.01.1988 - TC 8735679




225 MPa;



50%;







(b) width +/- 1%

Op. 24.02.2015 Dec. 11.05.2015 - TC 1507697

7212.40.00 COILS, non-alloy steel, prepainted, hot dipped zinc coated,



440 MPa;


than 550 MPa;





(g) prepainted steel with a specular gloss level at 60 degrees

NOT less than 40 units and NOT more than 95 units as

defined by Australian/New Zealand Standard

AS/NZS 1580.602.2:1995;

(h) thickness 0.35 mm OR 0.40 mm OR 0.45 mm OR 0.5 mm;

(i) width 515 mm,


specification (h) and (i) are EITHER of the following:

(i) width + 3 mm;

(ii) thickness + OR - 0.03 mm

Op. 14.11.2013 Dec. 10.02.2014 - TC 1338603

7212.40.00 STEEL, flat rolled, in coil form, continuous annealed, zinc

coated, epoxy lacquered, having BOTH of the following:

(a) thickness NOT greater than 0.4 mm;

(b) width NOT greater than 90 mm

Op. 09.04.2009 Dec. 03.07.2009 - TC 0912184

Tariff Description

===========================================================================


7212.50.00 SHEETS AND/OR STRIPS, STEEL, NON-ORIENTATED ELECTRICAL, as

described in ANY of the following international standards:

(a) Japanese Industrial Standard C 2552;

(b) American Society for Testing and Materials

Standard A 677-05;

(c) European Standard EN 10106

Op. 23.03.2006 Dec. 16.06.2006 - TC 0605627

7213.20.00 RODS, WIRE, hot rolled, free cutting steel, Grade 12L 14

Op. 07.11.2003 Dec. 30.01.2004 - TC 0314235

7213.91 RODS, tyre cord, dia 5.0 mm or greater but NOT exceeding 6.0 mm,

to Specifications AISI 1070 M or AISI 1080 M

Op. 01.07.1996 Dec. 12.06.1996 - TC 9607044

7214.10.00 STEEL BARS, complying with American Society of Testing and

Materials Standard A350-LF2 (ASTM A350-LF2)

Op. 19.04.2013 Dec. 26.07.2013 - TC 1313230

7214.30.00 BARS, HEXAGONAL, hot rolled, free cutting steel, grade 12 L 14

Op. 22.01.2007 Dec. 13.04.2007 - TC 0701138

7214.30.00 BARS, ROUND, hot rolled, free cutting steel, Grade 12L 14

Op. 07.11.2003 Dec. 30.01.2004 - TC 0314225

7214.20.00 REINFORCING BARS, CRYOGENIC, LIQUID NATURAL GAS STORAGE TANK,


(a) un-notched bar uniform elongation at maximum force

("Agt") NOT less than 3% at cryogenic temperature

minus 168 degrees Celsius;

(b) un-notched bar yield strength NOT less 575 MPa;

(c) transverse rib surface geometry

Op. 05.06.2013 Dec. 26.08.2013 - TC 1318643

7214.91.00 BARS, NON-ALLOY STEEL, having ALL of the following:

(a) rectangular cross-section;

(b) electrical resistivity NOT greater than 20 Micro Ohms

per centimetre;

(c) carbon content NOT greater than 0.06 percent

Op. 12.05.2008 Dec. 04.08.2008 - TC 0807796

7214.99.00 STEEL BARS, hexagonal, hot rolled steel, across the flat NOT

less than 33 mm and NOT greater than 65 mm

Op. 20.07.2011 Dec. 19.10.2011 - TC 1124116

7214.99.00 BARS, round, complying with Japanese Industrial Standard JIS G

4051 (1979), class S20C OR class S45C, having a bar diameter

NOT less than 100 mm

Op. 23.08.2010 Dec. 22.11.2010 - TC 1038857

7214.99.00 BARS, NON-ALLOY STEEL, having BOTH of the following:

(a) electrical resistivity NOT greater than 20 Micro Ohms

per centimetre;

(b) carbon content NOT greater than 0.06 percent

Op. 22.05.2008 Dec. 04.08.2008 - TC 0809491

7215.10 BARS, square, steel, bright OR cold finished, having an across

flat dimension of 40 mm or greater but NOT exceeding 150 mm

Op. 21.03.1985 Dec. 21.03.1985 - TC 8530419

7215.10.90 BARS, hexagon, bright OR cold finished to AS 1443-1994

specifications, having an across the flat dimension in ANY of the

following sizes:

Tariff Description

===========================================================================


(a) 57.15 mm;

(b) 60.325 mm;

(c) 60.00 mm;

(d) 62.00 mm OR greater

Op. 03.03.1998 Dec. 11.05.1998 - TC 9801834

7215.50 BARS, flat, steel, bright or cold finished, having dimensions

wider than 100 mm or thickness greater than 25 mm

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605781

7215.50 BARS, hexagon, bright or cold finished, having an across the flat

dimension in ANY of the following sizes:

(a) 57.15 mm (2 1/4 in. nominal);

(b) 60.325 mm (2 3/8 in. nominal);

(c) 60.00 mm;

(d) 62.00 mm or greater

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605783

7215.50 BARS, square, steel, bright OR cold finished, having an across

flat dimension of 40 mm or greater but NOT exceeding 150 mm

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605853

7215.50.90 BARS, flat, cold-rolled or cold-drawn, having ALL of the

following:

(a) carbon NOT less than 0.18% and NOT greater than 0.23%;

(b) manganese NOT less than 0.3% and NOT greater than 0.65%;

(c) phosphorus NOT greater than 0.04%;

(d) sulphur NOT greater than 0.05%;

(e) thickness 10 mm AND width 40 mm;

(f) length 3 000 mm


specification (e) are +0.0 mm and -0.10 mm and (f) are +100 mm

and -0.0 mm

Op. 06.03.2015 Dec. 07.06.2015 - TC 1509481

7215.50.90 BARS, rectangular, bright drawn carbon steel, greater than 3 mm

width and thickness

Op. 01.07.1996 Dec. 04.03.1996 - TC 9602575

7215.90 WELDING TRANSITION JOINTS, composed of dissimilar metals,

explosion bonded, allowing dissimilar metals to be welded together

Op. 31.03.1988 Dec. 13.10.1988 - TC 8803423

7215.90 BARS, flat, high carbon spring steel, tempered and hardened to give

a tensile strength 80 to 90 tons/sq in, in straight lengths, cross

sectional dimensions 9 to 13 mm wide, 2.5 to 5 mm thick

Op. 07.05.1990 Dec. 09.08.1990 - TC 9004401

7216.32.00 I-BEAMS, tapered flange, hot-rolled, complying with Australian

Standard/New Zealand Standard 3679.1-300 (AS/NZS 3679.1-300) OR

Australian Standard/New Zealand Standard 3679.1-350 (AS/NZS

3679.1-350), having ALL of the following:

(a) length greater than 5.9 m but NOT greater than 15.1 m;

(b) nominal flange widths of either 45.0 mm OR 65.0 mm;

(c) flange thickness greater than 5.9 mm but NOT greater

than 8.6 mm;

(d) mass greater than 7.1 kg/m but NOT greater than 13.2 kg/m;

(e) height NOT greater than 130 mm

Op. 06.03.2014 Dec. 03.06.2014 - TC 1408682

7216.32.00 I BEAMS, hot rolled, having EITHER of the following:

(a) depth NOT less than 356 mm (14 in) and a flange width NOT

less than 368 mm (14.5 in);

Tariff Description

===========================================================================


(b) depth NOT less than 762 mm (30 in) and a flange width NOT

less than 267 mm (10.5 in)

Op. 04.10.2005 Dec. 03.01.2006 - TC 0513491

7216.50.00 BARS, MILD STEEL, being wheel rim profiles, length NOT less than

5 m

Op. 19.12.2005 Dec. 10.03.2006 - TC 0516804

7216.61.00 STRUTS, CHANNEL, non-alloy steel

Op. 25.05.2011 Dec. 19.08.2011 - TC 1116444

7216.99.00 RAILS, MOBILE RACKING SYSTEM, trapezoidal, grooved OR ungrooved,

having a height NOT greater than 40 mm

Op. 13.06.2013 Dec. 11.11.2013 - TC 1319651

7216.99.00 HANGING TRACKS, STRIPPING AND BRACKETS, steel, wall mounted,

having spaced screw holes

Op. 01.09.2010 Dec. 29.11.2010 - TC 1040551

7216.99.00 STRIP, SOIL REINFORCEMENT, having ALL of the following:

(a) composition to Australian Standard AS3679.1 Grade 350

or equivalent;

(b) hot rolled;

(c) transverse ribs, having a height NOT less than 2.5 mm and

NOT greater than 4.5 mm;

(d) galvanized;

(e) attachment holes at one or both ends of the strip;

(f) width NOT less than 40 mm and NOT greater than 60 mm;

(g) thickness NOT less than 3 mm and NOT greater than 10 mm,

excluding height of ribs;

(h) length NOT greater than 15 metres

Op. 30.04.2007 Dec. 20.07.2007 - TC 0706227

7217.10 WIRE, to the following Specifications:

(a) ASTM A230;

(b) DIN 17223

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605787

7217.10 WIRE, oil tempered round edge hardened spring steel, to

Specification AISI C 1070

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605855

7217.10 WIRE, steel, to ANY of the following Specifications:

(a) ASTM A230, A232 or A401;

(b) SAE J351 or 50100 to 52100 (both inclusive);

(c) DIN 17223;

(d) BS 1408 Type D or 2803;

(e) JIS G3561

Op. 01.07.1996 Dec. 12.06.1996 - TC 9606969

7217.10 WIRE, oil tempered spring steel, having EITHER of the following:

(a) a dia NOT exceeding 1.25 mm;

(b) a dia exceeding 10.16 mm

Op. 01.07.1996 Dec. 21.06.1996 - TC 9607806

7217.10 WIRE, music spring, having ANY of the following finishes:

(a) bright;

(b) cadmium;

(c) cadmium/zinc alloy;

(d) galvanised;

(e) phosphate;

(f) polished;

(g) tinned

Op. 01.07.1996 Dec. 21.06.1996 - TC 9607812

Tariff Description

===========================================================================


7217.10 WIRE, oil tempered round edge hardened spring steel, to

Specification AISI C1065 in layer wound coils

Op. 01.07.1996 Dec. 21.06.1996 - TC 9607813

7217.10 WIRE, brick cutting

Op. 01.07.1996 Dec. 02.07.1996 - TC 9608374

7217.10.00 WIRES, FASTENER, complying with American Iron and Steel

Institute (AISI) Standard 1022

Op. 16.05.2007 Dec. 07.08.2007 - TC 0707304

7217.10.00 WIRE, STEEL, having BOTH of the following:

(a) diameter NOT less than 2.5 mm but NOT exceeding 3.5 mm;

(b) chemical composition by weight of ALL of the following:

(i) carbon 0.06% to 0.11%;

(ii) phosphorus 0.04% to 0.08%;

(iii) manganese 0.80% to 1.00%;

(iv) silicon 0.01% maximum;

(v) sulphur 0.015% to 0.07%;

(vi) nickel 0.006% to 0.012%;

(vii) aluminium 0.005% maximum

Op. 26.09.2000 Dec. 08.12.2000 - TC 0008138

7217.10.00 WIRE, STEEL, having BOTH of the following:

(a) diameter NOT less than 2.5 mm but NOT exceeding 3.5 mm;


(i) carbon 0.06% to 0.14%;

(ii) phosphorus 0.03% to 0.09%;


(iv) silicon 0.14% maximum;

(v) sulphur 0.01% to 0.04%

Op. 24.04.2001 Dec. 20.07.2001 - TC 0103705

7217.20 WIRE, galvanised, dia less than 0.90 mm

Op. 01.07.1996 Dec. 11.06.1996 - TC 9604139

7217.20 STAPLE WIRE, galvanised

Op. 01.07.1996 Dec. 25.06.1996 - TC 9605656

7217.20 WIRE, galvanised, annealed, non-alloy steel, having ALL of the

following characteristics:

(a) diameter of 1.00 mm or less;

(b) diameter tolerance + 0.02 mm - 0.01 mm;

(c) tensile strength 300 - 400 N/mm2;

(d) elongation 18% minimum;

(e) torsion 44 turns minimum

Op. 01.07.1996 Dec. 12.06.1996 - TC 9606972


(a) bright;

(b) cadmium;


(d) galvanised;

(e) phosphate;

(f) polished;

(g) tinned

Op. 01.07.1996 Dec. 19.06.1996 - TC 9607636

7217.90 WIRE, cold drawn, fully killed, modified, spheroidised, annealed

in process, phosphate coated to Specification AISI K1062M

Op. 01.07.1996 Dec. 11.06.1996 - TC 9604145

7217.90 WIRE, fastener, soft drawn, to ANY of the following

Tariff Description

===========================================================================


Specifications:

(a) AISI Grade C1010;

(b) AISI Grade C1018;

(c) AISI Grade C1022;

(d) AISI Grade K1012;

(e) AISI Grade K1013;

(f) AISI Grade K1016;

(g) AISI Grade K1018;

(h) AISI Grade K1019;

(i) AISI Grade K1022;

(j) AISI Grade K10B18;

(k) AISI Grade K10B21

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605663

7217.90 WIRE, fastener, soft drawn, to ANY of the following

Specifications:

(a) AISI Grade C1038;

(b) AISI Grade C1039;

(c) AISI Grade C1040;

(d) AISI Grade C1041;

(e) AISI Grade K1038;

(f) AISI Grade K10B30

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605664


(a) bright;

(b) cadmium;


(d) galvanised;

(e) phosphate;

(f) polished;

(g) tinned

Op. 01.07.1996 Dec. 11.06.1996 - TC 9605786

7217.90.00 WIRE, STEEL, being hard drawn low carbon (HDLC) wire, phosphate

coated, having ALL of the following:

(a) diameter NOT less than 18.00 mm but NOT greater than

20.00 mm;


(i) carbon 0.04% to 0.10%;

(ii) phosphorus 0.03% maximum;


(iv) silicon 0.12% to 0.24%;

(v) sulphur 0.03% maximum

Op. 11.08.2008 Dec. 31.10.2008 - TC 0825942

7217.90.00 WIRE, SPIRAL BINDING, nylon coated, continuous roll, diameter

0.74 mm to 2.00 mm (inclusive)

Op. 01.07.1996 Dec. 11.03.1996 - TC 9603035

7217.90.00 WIRE, fastener, soft drawn, to specification AISI grade K 4037

Op. 01.07.1996 Dec. 21.06.1996 - TC 9607835

7218.10.00 INGOTS, stainless steel, weight exceeding 2.5 tonnes

Op. 22.07.1993 Dec. 29.10.1993 - TC 9307092

7218.99.00 BILLETS, stainless steel, having a chromium content NOT less

than 10.5%

Op. 02.10.2015 Dec. 04.01.2016 - TC 1537232

7218.99.00 BILLETS OR BLOOMS, stainless steel, square, forged and ground,

having a section measurement of NOT less than 75 mm and NOT

greater than 500 mm

Op. 29.11.2004 Dec. 04.02.2005 - TC 0413053

Tariff Description

===========================================================================


7219.12.00 COILS, stainless steel, to ASTM A240, in ANY of the following

grades:

(a) 316;

(b) 316L;

(c) 304;

(d) 304L;

(e) 321;

(f) UNS S41050

Op. 27.03.1997 Dec. 30.07.1997 - TC 9702511

7219.12.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of

4.75 mm or more but NOT exceeding 10 mm

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704869

7219.13.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of 3 mm

or more but less than 4.75 mm

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704872

7219.21 FLAT ROLLED PRODUCTS, having a nickel content exceeding 22.5%

by weight

Op. 01.01.1988 Dec. 01.01.1988 - TC 8800536

7219.21.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS S30815, having a

chemical composition by weight of ALL of the following:

(a) carbon 0.1% maximum;

(b) silicon 1.40% to 2.00% (both inclusive);

(c) manganese 0.8% maximum;

(d) phosphorous 0.040% maximum;

(e) sulphur 0.030% maximum;

(f) chromium 20% to 22% (both inclusive);

(g) nickel 10% to 12% (both inclusive);

(h) cerium 0.03% to 0.08% (both inclusive);

(i) nitrogen 0.14% to 0.20% (both inclusive)

Op. 21.01.1994 Dec. 29.04.1994 - TC 9401453

7219.21.00 PLATES, stainless steel, types 304 and 316 to ASTM A240

Op. 21.11.1994 Dec. 19.05.1995 - TC 9409119

7219.21.00 PLATES, stainless steel, to specification ASTM A240, having a

thickness exceeding 10 mm and a width exceeding 600 mm

Op. 31.05.1995 Dec. 08.09.1995 - TC 9505858

7219.21.00 PLATES OR SHEET, stainless steel, to standard AISI 420

Op. 10.04.1996 Dec. 12.07.1996 - TC 9605616

7219.21.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness

exceeding 10 mm

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704868


by weight

Op. 01.01.1988 Dec. 01.01.1988 - TC 8800535

7219.22.00 FLAT ROLLED PRODUCTS, stainless steel, Grade UNS 31803, having a

chemical composition, by weight, of ALL of the following:

(a) carbon 0.3% maximum;

(b) chromium 21.0-23.0% inclusive;

(c) nickel 4.5-6.5% inclusive;

(d) molybdenum 2.5-3.5% inclusive;

(e) nitrogen 0.08-0.20% inclusive;

(f) silicon 1.0% maximum;

(g) manganese 2.0% maximum;

(h) phosphorus 0.03% maximum;

Tariff Description

===========================================================================


(i) sulphur 0.02% maximum

Op. 10.12.1992 Dec. 12.03.1993 - TC 9300330

7219.22.00 PLATES, stainless steel, types 304 and 316 to ASTM A240, having a

thickness greater than 6mm

Op. 21.11.1994 Dec. 19.05.1995 - TC 9409118

7219.22.00 PLATES, stainless steel, to specification ASTM A240, having a

thickness exceeding 6 mm but NOT exceeding 10 mm and a width

exceeding 600 mm

Op. 31.05.1995 Dec. 08.09.1995 - TC 9505856



Op. 02.06.1997 Dec. 15.08.1997 - TC 9704870



Op. 02.06.1997 Dec. 15.08.1997 - TC 9704878

7219.24.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness of less

than 3 mm

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704894


4.75 mm or more

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704877


by weight

Op. 01.01.1988 Dec. 01.01.1988 - TC 8800531

7219.32.00 PLATES, SHEETS OR COILS, stainless steel, to ASTM A240, in ANY of

the following grades:

(a) 316;

(b) 316L;

(c) 304;

(d) 304L;

(e) 321;

(f) UNS S41050;

(g) 430

Op. 27.03.1997 Dec. 30.07.1997 - TC 9702513



Op. 02.06.1997 Dec. 15.08.1997 - TC 9704893

7219.33.00 STAINLESS STEEL STRIP, cold rolled, heat resisting, ferritic,

type 409, in coils, AISI type 2D finish, having the following

dimensions:

(a) thickness 1.5 mm, 1.2 mm, or 2.0 mm (+ or - 10%);

(b) width between 600 mm and 1 300 mm inclusive

Op. 04.10.1996 Dec. 13.12.1996 - TC 9611258



(a) 316;

(b) 316L;

(c) 304;

(d) 304L;

(e) 321;

(f) UNS S41050;

(g) 430

Op. 27.03.1997 Dec. 30.07.1997 - TC 9702503

Tariff Description

===========================================================================


7219.33.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, having a thickness

exceeding 1 mm but less than 3 mm

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704859

7219.34.00 STAINLESS STEEL STRIP, cold rolled, heat resisting, ferritic, type

409, in coils, AISI type 2D finish, having the following dimensions;

(a) thickness 0.9 mm, 0.6 mm, or 1.00 mm (+ or - 10%);

(b) width between 600 mm and 1 300 mm inclusive

Op. 04.10.1996 Dec. 13.12.1996 - TC 9611259



(a) 316;

(b) 316L;

(c) 304;

(d) 304L;

(e) 321;

(f) UNS S41050

Op. 27.03.1997 Dec. 30.07.1997 - TC 9702502



Op. 02.06.1997 Dec. 15.08.1997 - TC 9704860



(a) 316;

(b) 316L;

(c) 304;

(d) 304L;

(e) 430

Op. 27.03.1997 Dec. 30.07.1997 - TC 9702499


than 0.5 mm

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704861

7219.90.00 SHEET, COMPOSITE, stainless steel laminated with polyvinyl

chloride, having BOTH of the following:

(a) steel thickness NOT less than 0.6 mm;

(b) polyvinyl chloride laminate thickness NOT less than

0.8 mm

Op. 01.08.2005 Dec. 21.10.2005 - TC 0510004

7219.90.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704862

7219.90.00 CAUL PLATES (melamine press plates), stainless steel, being 2 650 mm

x 1 350 mm OR greater

Op. 16.11.1998 Dec. 22.01.1999 - TC 9810123


4.75 mm or more

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704863

7220.12 BARS OR STRIP, stainless steel, hot rolled, coil form,

in ANY of the sizes listed in the following TABLE

THE TABLE

Thickness Width

(a) less than 0.55 mm less than 152 mm

(b) 0.55 mm to 3 mm less than 24 mm

(c) greater than 3 mm less than 25 mm

Op. 14.07.1994 Dec. 14.07.1994 - TC 9217823

Tariff Description

===========================================================================



than 4.75 mm

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704865

7220.20 STRIP, stainless steel, thickness less than 0.26 mm, of

rectangular section, of a width NOT exceeding 500 mm and of

such dimension that the thickness does NOT exceed one tenth

of the width

Op. 28.02.1984 Dec. 28.02.1984 - TC 8437425

7220.20.00 BANDING, stainless steel, to AISI 201 or 316, of a width less than

35 mm and a thickness of less than 1.25 mm

Op. 18.05.1993 Dec. 30.08.1993 - TC 9304905

7220.20.00 STRIP, stainless steel, grade 301, in coils, thickness NOT

exceeding 0.3 mm, width NOT exceeding 600 mm

Op. 11.04.1994 Dec. 15.07.1994 - TC 9404089



(a) 316;

(b) 316L;

(c) 304;

(d) 304L;

(e) 321;

(f) UNS S41050;

(g) 430

Op. 27.03.1997 Dec. 30.07.1997 - TC 9702580

7220.20.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL, NOT further worked than

cold-rolled (cold-reduced)

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704864

7220.90.00 STRIP, stainless steel, type 434, coated on one or both sides with

primer and chemically reactive adhesive system

Op. 21.03.1994 Dec. 02.08.1994 - TC 9403739

7220.90.00 FLAT ROLLED PRODUCTS OF STAINLESS STEEL

Op. 02.06.1997 Dec. 15.08.1997 - TC 9704866

7221.00 BARS AND RODS, hot rolled in irregularly wound coils, stainless

steel, Dia. 40mm or less

Op. 29.09.1992 Dec. 15.01.1993 - TC 9209110

tco 7201 to 7221 - · pdf fileg3134 (jis g3134), grade spfh590, having all of the following:...

Documents