technology: digital communications - welders, welding ......technology arclinktm communications 4/12...
TRANSCRIPT
Technology has pushed us into thedigital era. From video cameras tophones, “digital” is replacing “analog”.Why?
Digital Communications allow forfaster, more dependable, moreeconomical equipment performance.Historically, welding system performance has been limited by theanalog circuitry that controlled it.Analog signals can only be transmittedover limited distances, as the signalsattenuate or “die out” over longerdistances, compromising data integrityand limiting the cable distancesbetween welding system components.
Digital Communications promote fastersignal transfer, while preserving dataintegrity and simplifying wiring. A digitalprotocol also provides a scalableframework for future upgrades, whichallows engineering changes to bemade through software upgradesinstead of module replacements.Digital Communications speed up datatransfer rate and minimize delay,enhancing welder performance.
SPEED OF PERFORMANCEDelays are reduced, allowing more data to be transferred in less time.
FLEXIBILITY/SCALABILITYNew features can be added to existing equipment through software upgrades,and new components can easily be added to an existing welding cell.
COST REDUCTIONA single cable between multiple devices is less expensive and more efficient.
SIMPLIFIED EQUIPMENT MAINTENANCECalibration between the power source and robot is not necessary, even afterfeatures are added to an existing system.
PROCESS CONTROLSAll weld process controls are accessible from a single user interface controlpanel.
PRODUCTION MONITORINGHigh-speed communications enable the use of software tools to trackequipment usage and condition, allow configuration of limits and responsesafter each weld, and provide storage of thousands of weld summaries.
Digital Communications
T E C H N O L O G Y
D I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
The Power Wave 450 was an analog welding system. New welding features required additional wiring and calibration between the robot
and power source. Weld process controls were found on both the welding power source and at the robot controller.
NX-1.20 3/06
T h e f u t u r e o f w e l d i n g i s h e r e . ®
The Power Wave 455M is a digital welding system. New welding features can be added without additional wiring or
calibration. All weld process controls are accessible from the robot teach pendant or hard automation control interface.
Improves Productivity, Quality and Safety
TECHNOLOGY
2/12Integration PossibilitiesD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
Power Wave
Power Feed 10M Semiautomatic
Wire Feeder
ProcessMonitoring
ProcessMonitoringPower WaveComputerInternet
DeviceNetGateway
FANUC Robot
Power Feed 10RRobotic Wire
Feeder
Robot Teach Pendant
PLC or Hard AutomationUser Interface
DeviceNet Compatible Robot
FANUC R-J3 or R-J3iBRobot Controller
Ethernet/DeviceNetGateway
The Power Wave Welding Systems are used insemiautomatic, hard automation, and in roboticapplications. In addition, a number of useful LincolnElectric developed PC tools, ranging fromdiagnostics to advanced production monitoring areavailable for use on these systems.
Lincoln Electric uses a digital communicationssystem called ArcLinkTM in all of its Power WaveWelding Systems. ArcLink was specifically designedfor the arc welding environment and is thebest method of communicating to cellcomponents such as semiautomatic wire
Seamless Integration
T h e f u t u r e o f w e l d i n g i s h e r e .®
feeders or robots. ArcLink is simply the way eachpiece "talks" to each other in a Power Wave system.The Power Wave Welding Systems also provide"gateways" to allow other digital networks such asDeviceNetTM and Ethernet to connect to theArcLink system.
This Nextweld Digital Communications documentexplains the ArcLink, DeviceNet, and Ethernetcommunications protocols as well as assists in
defining which is the best fit for yourapplications.
Optional GatewayModules
T E C H N O L O G Y
3/12Comparing Communications ProtocolsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
Which Communications Protocol do I Need?
Use ArcLinkFor These Applications
Semiautomatic WeldingThe new series of Power Feed 10M and Power Feed 25Msemiautomatic wire feeders support ArcLink DigitalCommunications.
Robotic WeldingRobots compatible with ArcLink protocol offer “Best-in-Class” performance through:• A robot teach pendant that
• provides access to all of the Power Wave features.• eliminates the need for a user panel on the power
source.• provides detailed power source fault/alarm information.• enables searches of the procedures that are
programmed in the power source.• The ability to switch dynamically among 8 different
welding schedules while welding.• An arc start response time of 5 - 10 msec or less.• Touch-sensing performance that is available with no
additional hardware. Touch-sensing enables search speeds of 100 mm/sec with 0.045 (1.2 mm) steel wire.
• Full support of Lincoln diagnostic packages through R-J3iB Ethernet port.
• FANUC Through the Arc Seam Tracking (T.A.S.T.)performance, which is available with no additionalhardware to provide updates of actual weld current andvoltages at 250 Hz for improved seam trackingperformance.
ArcLink Compatible Robot Controllers
Use DeviceNetFor These Applications
Hard Automation WeldingPower Wave Welding Systems combined with theDeviceNet or Ethernet/DeviceNet Gateway willsupport any DeviceNet Programmable LogicControllers (PLC).
Robotic WeldingFor robots not compatible with ArcLink protocol, or forcustomers who simply prefer to integrate withDeviceNet, this protocol offers good performance andaccess to most power source features through therobot teach pendant. DeviceNet robots provide theability to switch dynamically between 2 differentwelding schedules while welding.
DeviceNet compatible RobotControllers• FANUC RJ3 and R-J3iB • ABB, Motoman, and others
Use EthernetFor These Applications
Production Monitoring and AdvancedDiagnosticsThese functions are available through the Ethernetport of the FANUC R-J3iB robot controller, orthrough the Ethernet/DeviceNet Gateway Board ofDeviceNet equipment.
FANUC R-J3 and R-J3iB
DeviceNet Gateway
Ethernet/DeviceNetGateway
T h e f u t u r e o f w e l d i n g i s h e r e .
T E C H N O L O G Y
4/12ArcLinkTM CommunicationsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
ArcLink is the leading digitalcommunications protocol forthe arc welding industry. Itintegrates all weldingcomponents for seamless, time-critical data transfer.The strength of ArcLink liesin the ability to communicatewith each system componentin a pre-defined weldinglanguage. In addition,ArcLink is an opencommunications protocol,meaning that Lincoln Electricpublishes how it works andencourages other companiesto adopt it.
ArcLink brings modularity towelding systems and providesa single, intelligent connectionbetween all modules. AnArcLink network can be assimple as a single stickwelder or as complicated asrobotic installations.
WhatIs ArcLink?
ArcLink provides flexiblewelding options for bothrobotic and semiautomaticapplications.
Power Wave 455MPalm™ w/ Weld
Manager
The ArcLinkcommunications protocolserves two purposes:as the native device language in Lincoln Electric welding systemcomponents, and as the interface for robotic welding applications. ArcLinkalso allows for networking capabilities through gateways (such asEthernet) to allow simultaneous monitoring of multiple welding cells, whichestablishes a means for developing supervisory or monitoring tools.
Robotic Power Feed 10R
Because of ArcLink,access to limitconfigurations, backup& restore of settingsand monitoring of arctime can now travelwith you on a hand-held computer.
The ArcLink Protocol
Semiautomatic Power Feed 10M
HowArcLink Works
ArcLink uses peer-to-peer, event-driven messaging, which broadcasts on an “as-needed” basis. Peer-to-peermessaging frees space on the data highway, reducing message traffic. Because ArcLink logic is based on aController Area Network (CANIIB) standard, it inherits the benefits of priority-based, deterministic messaging andnoise immunity. This means that critical messages are guaranteed to reach their destination with minimum delay,even in the presence of electrical noise. The ArcLink cable houses five conductors as depicted below.
5-pin ArcLink Connector
Leads D and E arededicated powerleads supplying 40 VDC, enoughpower to run the wirefeeder drive motor.This eliminates theneed for a separate wire feederpower cable.
Leads A and B are dedicated tocommunications. They carryCANIIB messages between weldingsystem components.
Lead C serves as the voltage sensory lead.Lincoln Electric digital welding machinessupply this lead within the ArcLink cable.Certain applications may require anadditional voltage sense lead.
A
B
C
D
E
T h e f u t u r e o f w e l d i n g i s h e r e .
T E C H N O L O G Y
5/12ArcLinkTM CommunicationsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
Using ArcLinkRobotic Integration ApplicationArcLink greatly improves the integration of the arc weldingprocess into automated arc welding systems, as theadvanced features of ArcLink provide process changing(between 8 weld schedules), file transfer, data acquisition,and component fault history capabilities. Semiautomatic ApplicationArcLink is used in semiautomatic applications as the methodof communication internal to each welding component.ArcLink provides many of the same benefits to semiautomaticapplications as it does to robotics, such as:• data monitoring• access to all weld process controls from a single user
interface• ability to boom-mount user interfacesArcLink Specifications• 5-conductor SO-type control cable with 5-pin connectors
for all interconnections• Isolated 40 VDC power supply• Multiple-sourced transceiver• Data rate of 125-500 Kbaud
FeaturesOf ArcLink
File Transfer• Weld files can be saved, shared, or modified. Data Acquisition• Weld data is collected and stored for
Production Monitoring™ purposes.Advanced Diagnostics• ArcLink provides the capability to monitor component
failures system wide.Ease of Installation• Uses one control cable for communications, component
power, and electrode voltage sensing connections.• Provides flexibility of physical configuration so that any
component may be connected to any other component inthe system.
BenefitsOf Using ArcLink
Modular System Configuration• Allows for creation of custom welding
system configurations.Rugged Hardware• Establishes a high degree of tolerance for electrically noisy
welding environments.Scalable System• Permits addition of new features and functionality without
changing the existing cabling.
Performance• Provides a repeatable and reliable method of
communication for time-critical welding applications.• Improves welding performance by increasing the
amount of shared information between weldingsystem components.
ArcLink Performance Metrics
Criteria Performance (compared to Analog)
Arc start/end times 50-80 % reductionLatency More deterministicProcess switching time 80 % reductionPart search (through the wire) speeds 100 % fasterArc current, voltage, and wire feed 500 % faster, forspeed telemetry arc seam tracking
Power Wave F355i/FANUC RJ3iB is an example of anArcLink Robotic Welding System
ArcLink Robotic systems allow weld mode searches by processand wire type through the robot teach pendant.
ArcLink Robotteach pendant
T h e f u t u r e o f w e l d i n g i s h e r e .
T E C H N O L O G Y
6/12DeviceNetTM CommunicationsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
DeviceNet is a communicationsprotocol widely used throughoutthe automotive, semiconductor,and packaging industries.
In its typical application,DeviceNet works in conjunctionwith a Programmable LogicController (PLC) and severalsystem devices to provide aframework for data traffickingand monitoring.
Strong conformance testingensures interoperability amongDeviceNet products. As aresult, users can mix andmatch products from a varietyof suppliers and integratethem seamlessly.Due to its widespreadpopularity and its ability to
Whatis DeviceNet?
Example of a DeviceNet welding system
HowDeviceNet Works
DeviceNet connectivity is established through a DeviceNet Gateway. DeviceNet carries data from thecomponents of the welding systems (slaves) to a Programmable Logic Controller (master). DeviceNetperforms deterministic messaging, so that all messages are assigned priorities, preventing interference ordestruction of important data. The DeviceNet connector houses five conductors, as depicted below. Becauseit only carries 24 VDC, an additional cable is required to power the wire feeder drive motor. Additionally, thiscable does not contain a voltage sensing lead.
Lead 3 is a grounding shield
Lead 1 is a dedicated powerlead supplying 24 VDC
Leads 2 and 4 are dedicated tocommunications. They carryDeviceNet messages to andfrom welding systemcomponents.
Lead 5 is a dedicatedpower lead supplying
24 VDC
5-pin DeviceNet Connector
interchange equipment with several vendors, Lincoln Electric employs DeviceNet for hardcell automation and non-ArcLink compatible robotic applications. Lincoln Electric PowerWave 455M and 655R have been tested and found to comply with ODVA ProtocolConformance Test Version A-13.
DeviceNet Gateway
The DeviceNet Protocol
T h e f u t u r e o f w e l d i n g i s h e r e .
T E C H N O L O G Y
7/12DeviceNetTM CommunicationsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
UsingDeviceNet
Robotic and Hard AutomationApplicationsThe Lincoln Electric ArcLink protocol paired withDeviceNet gateway board and a PLC provide theultimate answer to hard-cell automated welding.Lincoln Electric also employs DeviceNet in specificrobotic welding applications. The Power Wave 455Mand Power Wave 655 Robotic connect seamlessly torobot controllers and hard automation PLCs.
DeviceNet Specifications• 24 VDC power• 5-conductor shielded PVC control cable • Single-sourced transceiver• Opto-isolator optional• Data rate of 125-500 Kbaud
FeaturesOf DeviceNet Gateway
Configuration Software• Programs the master/slave relationship between the
PLC and the welding system components.• Sets the scan rate for the polled input/output.• Allows configuration of basic system parameters.
User Interface Software• Provides the user access to all welding
process controls. • Provides ability to search the weld database.
Open DeviceNet Vendors Association(ODVA) Compliance• Lincoln Power Wave 455M and 655 Robotic have
been tested and found to comply with ODVA ProtocolConformance Test Version A-13.
BenefitsOf Using DeviceNet
Interchangeable• Due to the open construction of the protocol, multiple
vendors’ equipment can be used for replacements.
Hard Automation
Robotic
A Typical DeviceNet Welding System Configuration
Power Wave 455M with DeviceNet Gateway
Programmable Logic Controller (PLC)
Allen-BradleyTM PanelViewUser Interface
Power Wave 455M with optionalDeviceNet Gateway
24 Volt Power Supply
T h e f u t u r e o f w e l d i n g i s h e r e .
User Supplied
T E C H N O L O G Y
8/12Ethernet Communications D I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
WhatIs Ethernet?
Ethernet is the networkingchampion for information-layer communications.
Ethernet has been anetworking standard fordecades, which translates toreadily available equipmentand an expansive knowledge base.
The data rate at which anEthernet network operatesprovides the ability to pulllarge amounts of informationinto monitoring andsupervisory applications.Ethernet can be networkedover great distances and hasthe ability to distributeinformation to Local or WideArea Networks (LAN or WAN). Communications between ArcLink and
Ethernet enable equipment tracking and production monitoring
The messages are relayed overEthernet to either a LAN or WAN,
offering unlimited data access(Intranet, Internet, etc.)
Ethernet encapsulatesand preserves the
ArcLink data portion ofthe message
HowEthernet Works
Higher baud rate and non-deterministic messaging make Ethernet an excellent choice for use in applicationsthat do not require time-critical messaging. For this purpose, Lincoln Electric employs the Ethernet interface togather and store large amounts of information. Ethernet provides easy access to the stored data. Lincolnutilities extract the information into reports about equipment use and function.
Power Wave 455M with Ethernet/DeviceNet Gateway
Lincoln Electric now alsosupports wireless
Ethernet communications
The Ethernet Protocol
T h e f u t u r e o f w e l d i n g i s h e r e .
T E C H N O L O G Y
9/12Ethernet CommunicationsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
Using EthernetEthernet Data AcquisitionEthernet has proven itself as a robust communicationsprotocol, able to collect large amounts of data oversmall time intervals, and able to broadcast thatinformation over local or wide area networks(LAN or WAN).
Information storage on a LAN or WAN provides theability to monitor and control all equipment from a singledesktop computer.
Production Monitoring™Each welding system component is assigned anInternet Protocol (IP) address. Groups of addresses aretermed “subnets”. Ethernet records data from eachsubnet, allowing for equipment tracking. Software toolsthat detail allocation of resources such as consumablesused or time spent welding per machine are available.
FeaturesOf Production Monitoring
Management Utilities• Keep track of equipment usage and condition.• Allow configuration of limits and responses after
each weld.• Provide storage of thousands of weld summaries.
Advanced Configuration and DiagnosticFeatures• Track equipment fault and alarm histories.
Multiple Machine Management• Access data through a LAN or WAN to
manage the software of a large number ofmachines simultaneously.
• Upgrade software of all machines from one locationinstead of individual machine upgrades.
• Tools for creating customized Ethernetinterface applications.
BenefitsOf Ethernet Gateway
Fast Data Rate• Operating at a baud rate of 10-100 MHz, Ethernet
relays communications faster than low-level control protocols.
Standard Top-Layer Protocol• Standardized physical connections are commercially
available and inexpensive.
Networking• Ethernet maintains high-speed performance over
long distances, allowing for network capabilities.
View Robotic, Hard Cell, and Semiautomatic Equipment Simultaneously
Training: Automated feature that records thevalues of a test weld and uses those values as a
baseline for the limit on future welds.
View Process Details to Verify Process Selection
Event logs display fault and alarm conditionsof each machine component
Production Monitoring allows user to configure limitsand responses after each weld
T h e f u t u r e o f w e l d i n g i s h e r e .
The Weld History records thousandsof weld summaries
T E C H N O L O G Y
10/12Digital Communications ProductsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
Power Wave 355M/Power FeedTM 10M
The Power Wave 355M is the smaller, lighter version of thePower Wave 455M – same machine, just leaner and lighter.• The Power Wave 355M/Power Feed™10M welding
system is factory programmed with over 60 standardwelding programs to optimize the arc for a variety ofmaterials or applications, including steel, stainless steel,aluminum, nickel alloys and others.
• ArcLink Digital Communication between componentsallows unprecedented waveform control and expansioncapability. Simply selecta program and you havethe right arccharacteristics for yourapplication.
• The software isupgradeable, so yourPower Wave 355M willgrow with your business.If you want to reducecosts by buying aversatile machine thatwill do multiple jobs andlast for years to come,the high efficiency PowerWave 355M delivers.
Power Wave 455M Robotic, Power Wave 455M/STT Robotic
These Power Waves are designed to be part of amodular, multi-process welding system. • The Power Wave 455M Robotic and 455M/STT
Robotic are high performance, digitally controlledinverter welding power sources capable of complex,high-speed waveform control.
• Digital Communications enable the Power Wave toconnect seamlessly to robot controllers and hardautomation PLCs. Semi-automatic applications arealso supported.
• Optional DeviceNet andEthernet communicationmodules provide networkingcapabilities and allowprocess and productionmonitoring.
• Software-based controls canbe upgraded as newfeatures become available.
Power FeedTM 10MPower Feed 10M is a compact wire feeder designedfor use with Power Wave power sources. Some of the features of the Power Feed 10M include:• Push-pull system • New MSP 4 User Interface• 36 Segment Digital Display• Limit Settings• Lock Out Control• Arc control settings for all processes• Palm OS based hand held computer access to:
• Limit configuration• Back-up• Diagnostics
Power Wave Welding Systems: Simple. Innovative. Technologically Advanced.
ArcLink DeviceNet Ethernet
ArcLink Ethernet
Lincoln Welding Systems featuring Digital Communications
capabilities and allowsprocess and productionmonitoring.
• Software-based controlscan be upgraded as newfeatures becomeavailable.
• The Power Wave 655Rhas an output range of20-880 Amps.
ArcLink DeviceNet Ethernet
T h e f u t u r e o f w e l d i n g i s h e r e .
Power Wave 655 Robotic
The Power Wave 655R was designed for Robotic and HardAutomation applications that require extra power (650 Ampsat 100 % Duty Cycle)• Digital Communications enable the Power Wave to
connect seamlessly to robot controllers and hardautomation PLCs. Semi-automatic applications arealso supported.
• The Ethernet/Device/Net Gateway provides networking
T E C H N O L O G Y
11/12Digital Communications ProductsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
Power Wave® AC/DC 1000™
The Power Wave AC/DC 1000 is a modular weldingsystem with a single range of control from 100 to 2500Amps per arc at 100 % duty cycle The Power Wave AC/DC 1000provides:• DC+, DC- and Variable
frequency up to 200 Hertz• Flexible Waveform Control
• Variable Frequency• Variable independent
amplitudes• Variable timing• The Power Wave AC/DC
is 100 % softwarecontrolled
Power Wave F355i
The Power Wave F355i is fully integrated with the FANUCARC Mate™ R-J3iB controller and designed for the mostdemanding robotic applications. • This compact unit delivers 350 Amps @ 60% duty
cycle for MIG, PulsedMIG or Flux-Coredwelding applications.
Power Wave Welding Systems: Simple. Innovative. Technologically Advanced.
Power Feed Wire Feed SystemsPower Feed 10M
This compact wire feeder is designed for field construction,pipelines, offshore, and shipyard applications. The PowerFeed 10M is essential for applications where portability,
ruggedness and arcperformance aredemanded. It is designedto work exclusively withthe Power Waves.
Power Feed 10R
The Power Feed 10R is a high performance, digitallycontrolled, modular wire feeder designed to be a part of amodular, multi-process welding system. It is specifically designed to mount to a robot arm or to use inhard automation applications in various types of industries.This four drive roll feeder operates on 40 VDC input powerand is designed to be used with ArcLink Robotic PowerWave power sources.Close integration of thefeeder, power source,and customer’sequipment create thefoundation for a systemwith superior weldingperformance andreliability.
ArcLink DeviceNet Ethernet
ArcLink Ethernet* ArcLink
ArcLink
Lincoln Welding Systems featuring Digital Communications
• The Power WaveF355i/ARC MateR-J3iB communicatesvia ArcLink™, allowingall welding proceduresand process controlsto be managedthrough the ARC Materobot teach pendant –one central control forsetup, process controland diagnostics.
* Ethernet access is available throughthe Ethernet port of the R-J3iB
T h e f u t u r e o f w e l d i n g i s h e r e .
T E C H N O L O G Y
12/12Digital Communications ProductsD I G I T A L C O M M U N I C A T I O N S T E C H N O L O G Y
Power MIG 350MP
The Power MIG 350MP – a single phase,multi-process, synergic wire feederwelding package for the professionalwelder.The Power MIG 350MP offers:• Superior multi-process welding.• Synergic design for ultimate control over
the arc, by automatically aligning wirefeed speed and voltage.
• Top-quality aluminum welds with push-pull wire feed capability, not usuallyavailable in competitive models.
• True MIG pulsing and Pulse-on-Pulse™capabilities, which ensure that superiorfeeding is matched by high quality arcperformance.
ArcLink
Lincoln Welding Systemsfeaturing Digital Communications
Customer Assistance Policy
The business of The Lincoln Electric Company is manufacturing and selling high quality weldingequipment, consumables, and cutting equipment. Our challenge is to meet the needs of ourcustomer and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric foradvice or information about their use of our products. We respond to our customers based on thebest information in our possession at that time. Lincoln Electric is not in a position to warrant orguarantee such advice, and assumes no liability, with respect to such information or advice. Weexpressly disclaim any warranty of any kind, including any warranty of fitness for any customer’sparticular purpose, with respect to such information or advice. As a matter of practicalconsideration, we also cannot assume any responsibility for updating or correcting any suchinformation or advice once it have been given, nor does the provision of information or advicecreate, expand or alter any warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products soldby Lincoln Electric is solely within the control of, and remains the sole responsibility of thecustomer. Many variables beyond the control of Lincoln Electric affect the results obtained inapplying these types of fabrication methods andservice requirement.
Subject to change - This information is accurate to the best of our knowledgeat the time of printing. Please refer to www.lincolnelectric.com for any updated information.
T h e f u t u r e o f w e l d i n g i s h e r e .
WHAT IS NEXTWELD?
The challenges facing industrialfabricators today are growing in numberand complexity. Rising labor, materialand energy costs, intense domestic andglobal competition,a dwindling pool ofskilled workers,more stringent andspecific qualitydemands allcontribute to amore difficultweldingenvironment today.
Through ourcommitment toextensive research and investments inproduct development, Lincoln Electrichas established an industry benchmarkfor applying technology to improve thequality, lower the cost and enhance theperformance of arc welding processes.Advancements in power electronics,digital communications and WaveformControl TechnologyTM are the foundationfor many of the improvements.
NEXTWELD brings you a series ofProcess, Technology, Application andSuccess Story documents like this one.NEXTWELD explains how technologies,products, processes and applications arelinked together to answer the importantquestions that all businesses face:
• How can we work faster, smarter,more efficiently?
• How can we get equipment andpeople to perform in ways they’venever had to before?
• How do we stay competitive?
NEXTWELD is the future of welding butits benefits are available to you today.Ask your Lincoln Electric representativehow to improve the flexibility, efficiencyand quality of your welding operations toreduce your cost of fabrication.
THE LINCOLN ELECTRIC COMPANYwww.lincolnelectric.com1.216.481.8100
*Note: Ethernet and Production Monitoring are not an option on thePower MIG 350MP digital welding system.