tender documentengineeringprojects.com/tender/uploadfiles/3662_vol_-_iii.pdftrenches or drains (not...
TRANSCRIPT
TENDER DOCUMENT
NIT No.: NRO/CON/ALIMCO-FBD/752/677 dated 03.12.2018
FOR
Construction of Boundary Wall, 2 nos. gates & 2 nos. Guard room at ALIMCO’s new manufacturing set up of Aids and assisted devices at village Nawada Tigaon, Block Ballabgarh, district Faridabad (Haryana).
VOLUME – III
BOQ / PRICE BID
EXECUTING AGENCY
ENGINEERING PROJECTS (INDIA) LIMITED (A GOVT. OF INDIA ENTERPRISE)
Core-3, Scope Complex, 7,Lodhi Road, New Delhi-110003
TEL NO: 011-24361666, FAX NO. 011- 24363426
AN ISO 9001 & ISO 14001 COMPANY
In figures In words In figures In words
1 BOUNDARY WALL 10,635,759.66
2 02 Nos. MAIN GATE 1,060,119.36
302 Nos. SECURITY
ROOM 2,623,591.91
Total: 14,319,470.93
Rounded off 14,319,471.00
BIDDER'S FINANCIAL
OFFER :
In Figures
SEAL
In Words
SIGNATURE
* Bidders should submit separate sheet clearly showing base rate + GST / other Taxes, levies etc. as applicable.
* Rates should be inclusive of all taxes & duties and GST etc.
* Note-The Rates are based on DSR-2016, tenderer has to quote the rates above/ at par /below on DSR-2016 rates.
SL.No. ITEM
AMOUNT IN Rs. After adding percentage above/ below/ at par% QUOTE ABOVE/ BELOW / AT PAR ESTIMATED COST
(IN Rs.)
PRICE BID
BIDDER'S PRICE
Construction of Boundary Wall, 2 nos. gates & 2 nos. Guard room at ALIMCO’s new manufacturing set up of Aids and assisted devices at village Nawada
Tigaon, Block Ballabgarh, district Faridabad (Haryana).
SUMMARY OF COST
NRO/CON/ALIMCO-FBD/752/677
NRO/CON/ALIMCO-FBD/752/677
S.No DSR ITEMS 2016 AMOUNT
1 BOUNDARY WALL 10,635,759.66
2 MAIN GATE (MS GATE) 2 Nos 1,060,119.36
3 SECURITY ROOM 2 Nos 2,623,591.91
TOTAL 14,319,470.93
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF
AIDS AND ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON,
BALLABGARH, FARIDABAD ,HARYANA
SUMMARY OF BOUNDARY WALL,MAIN GATE & SECURITY ROOM
NRO/CON/ALIMCO-FBD/752/677
S.No
.
DSR ITEM
2016 Item Description Unit RATE Quantity Amount
EARTH WORK
1 2.8
Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or 10
sqm on plan), including dressing of sides and ramming
of bottoms, lift upto 1.5 m, including getting out the
excavated soil and disposal of surplus excavated soil
as directed, within a lead of 50 m.
2.8.1 All Kinds of soil CUM 166.40 576.89 95,994.50
2 2.25
Filling available excavated earth (excluding rock) in
trenches, plinth sides of foundations etc. in layers not
exceeding 20cm in depth, consolidating each
deposited layer by ramming and watering, lead up to
50 m and lift upto 1.5 m
CUM 125.75 432.67 54,408.25
3 2.28
Surface dressing of the ground including removing
vegetation and inequalities not exceeding 15 cm deep
and disposal of rubbish, lead up to 50 m and lift up to
1.5 m.
2.28.1 All kinds of soil (100 SQM) SQM 1,395.00 8.21 11,452.95
CONCRETE WORK
4 4.1.
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
4.1.101:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded
stone aggregate 40 mm nominal size).CUM 4,209.05 158.49 667,095.07
REINFORCED CEMENT CONCRETE
5 5.1
Providing and laying in position specified grade of
reinforced cement concrete, excluding the cost of
centering, shuttering, finishing and reinforcement - All
work up to plinth level :
5.1.21:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded
stone aggregate 20 mm nominal size).CUM 6,215.35 5.00 31,076.75
5.9Centering and shuttering including strutting, propping
etc. and removal of form for :
6 5.9.1Foundations, footings, bases of columns, etc. for mass
concrete.sqm 193.95 536.00 103,957.20
7 5.9.5
Lintels, beams, plinth beams, girders, bressumers and
cantilevers
sqm 342.90 917.94 314,761.63
8 5.9.6Columns, Pillars, Piers, Abutments, Posts and Struts.
sqm 467.85 690.70 323,142.12
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND
ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD ,HARYANA
CIVIL WORK -TYPE -BOUNDARY WALL
Page 1 of 3
NRO/CON/ALIMCO-FBD/752/677
S.No
.
DSR ITEM
2016 Item Description Unit RATE Quantity Amount
9 5.22
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position and
binding all complete upto plinth level.
5.22.6 Thermo-Mechanically Treated bars KG 56.60 7,600.00 430,160.00
10 5.22A
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position and
binding all complete above plinth level.
5.22A.6 Thermo-Mechanically Treated bars KG 56.60 7,500.00 424,500.00
5.33
Providing and laying in position machine batched and
machine mixed design mix M-25 grade cement
concrete for reinforced cement concrete work, using
cement content as per approved design mix, including
pumping of concrete to site of laying but excluding
the cost of centering, shuttering, finishing and
reinforcement, including admixtures in recommended
proportions as per IS: 9103 to accelerate, retard
setting of concrete, improve workability without
impairing strength and durability as per direction of
Engineer-in-charge.“(Note :- Cement content
considered in this item is @ 330 kg/cum.“Excess/ less
cement used as per design mix is payable/recoverable
separately).
11 5.33.1 All works upto plinth level cum 6,446.45 350.00 2,256,257.50
12 5.33.2 All works above plinth level upto floor V level cum 7,250.05 70.00 507,503.50
13 5.35
Add for using extra cement in the items of design mix
over and above the specified cement content therein. Quintal 672.75 150.00 100,912.50
BRICK WORK
14 6.2
Brick work with common burnt clay modular bricks of
class designation 7.5 in foundation and plinth in:
6.2.2 Cement Mortar 1:6 (1 cement : 6 coarse sand). CUM 4,400.50 300.00 1,320,150.00
15 6.4
Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in
all shapes and sizes in :
6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) CUM 5,582.85 375.00 2,093,568.75
Page 2 of 3
NRO/CON/ALIMCO-FBD/752/677
S.No
.
DSR ITEM
2016 Item Description Unit RATE Quantity Amount
STEEL WORK
16 16.53
Providing and fixing concertina coil fencing with punched
tape concertina coil 600 mm dia 10 metre openable
length ( total length 90 m), having 50 nos rounds per 6
metre length, upto 3 m height of wall with existing angle
iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9
horizontal R.B.T. reinforced barbed wire, stud tied with
G.I. staples and G.I. clips to retain horizontal, including
necessary bolts or G.I. barbed wire tied to angle iron, all
complete as per direction of Engineer-in-charge, with
reinforced barbed tape(R.B.T.) / Spring core (2.5mm
thick) wire of high tensile strength of 165 kg/ sq.mm with
tape (0.52 mm thick) and weight 43.478 gm/ metre (cost
of M.S. angle, C.C. blocks shall be paid separately)
metre 255.00 663.80 169,269.00
17 16.19
Supplying at site Angle iron post & strut of required size
including bottom to be split and bent at right angle in
opposite direction for 10 cm length and drilling holes
upto 10 mm dia. etc. complete.
KG 62.05 3,000.00 186,150.00
FINISHING
18 13.4 12 mm cement plaster of mix:
13.4.1 1:4 (1 cement: 4 coarse sand) sqm 180.85 4,000.00 723,400.00
19 13.42
Distempering with 1st quality acrylic distemper (ready
mixed) of approved manufacturer, of required shade
and colour complete, as per manufacturer's
specification.
13.42.1 Two or more coats on new work sqm 53.15 2,000.00 106,300.00
2013.46
Finishing walls with Acrylic Smooth exterior paint of
required shade :
13.46.1
New work (Two or more coat applied @ 1.67 ltr/10
sqm over and including priming coat of exterior
primer applied @ 2.20 kg/10 sqm)
sqm 96.05 4,000.00 384,200.00
2113.61
Painting with synthetic enamel paint of approved
brand and manufacture to give an even shade :
13.61.1 13.61.1 Two or more coats on new work sqm 78.40 2,000.00 156,800.00
22 13.80
Providing and applying white cement based putty of
average thickness 1 mm, of approved brand and
manufacturer, over the plastered wall surface to
prepare the surface even and smooth complete.
sqm 87.35 2,000.00 174,700.00
TOTAL 10635759.66
Page 3 of 3
NRO/CON/ALIMCO-FBD/752/677
S.No. DSR-16 Description Quantity Unit Rate Amount
1 10.25
Steel work welded in built up sections/
framed work, including cutting, hoisting,
fixing in position and applying a priming coat
of approved steel primer using structural
steel etc. as required.
10.25.2In gratings, frames, guard bar, ladder,
railings, brackets, gates and similar works
5,812.75 Kg 85.95 499,605.86
2 8.0
Marble work gang saw cut (polished and
machine cut) of thickness 18 mm for wall
lining (veneer work), backing filled with a
grout of average 12 mm thick in cement
mortar 1:3 (1 cement : 3 coarse sand),
including pointing with white cement mortar
1:2 (1 white cement : 2 marble dust)
with an admixture of pigment to match the
marble shade (To be secured to the backing
by means of cramps, which shall be paid for
separately).
8.1.1Raj Nagar Plain white marble/ Udaipur green
marble/ Zebra black marble.
8.1.1.2 Area of slab over 0.50 sqm 172.80 Sqm 3035.50 524,534.40
3 13.5 Applying priming coat:
13.50.4With ready mixed red oxide zinc chromate
primer of approved brand and manufacture
on steel work (second coat)
43.20 Sqm 15.60 673.92
-
4 13.62
Painting with synthetic enamel paint of
approved brand and manufacture of
required colour to give an even shade :
13.62.1
Two or more coats on new work over an
under coat of suitable shade with ordinary
paint of approved brand and manufacture
43.20 Sqm 112.30 4,851.36
Total 530,059.68
TOTAL GATE 2 Nos 1,060,119.36
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR
ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD ,HARYANA
SUMMARY OF MAIN GATE - 2 Nos
NRO/CON/ALIMCO-FBD/752/677
SUB
HEADDESCRIPTION AMOUNT
I CIVIL WORK 2,168,433.51
II ELECTRICAL 302,054.00
III PLUMBING 153,104.40
2,623,591.91
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND
ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
SUMMARY SHEET OF SECURITY ROOM (OPTION -1)
TOTAL (in Rs.)
Page 1 of 1
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR ITEM
2016 Item Description Unit RATE Quantity Amount
EARTH WORK
1 2.8
Earth work in excavation by mechanical means
(Hydraulic excavator) / manual means in foundation
trenches or drains (not exceeding 1.5 m in width or
10 sqm on plan), including dressing of sides and
ramming of bottoms, lift upto 1.5 m, including
getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50 m.
2.8.1 All Kinds of soil CUM 166.4 56.3 9,360.00
2 2.25
Filling available excavated earth (excluding rock) in
trenches, plinth, sides of foundations etc. in layers
not exceeding 20cm in depth, consolidating each
deposited layer by ramming and watering, lead up to
50 m and lift upto 1.5 m.
CUM 125.8 42.2 5,305.08
3 2.28
Surface dressing of the ground including removing
vegetation and inequalities not exceeding 15 cm
deep and disposal of rubbish, lead up to 50 m and lift
up to 1.5 m.2.28.1 All kinds of soil SQM 13.95 13.5 188.33
4 2.35.3
Treatment of soil under existing floors using chemical
emulsion @ one litre per hole, 300 mm apart
including drilling 12 mm diameter holes and plugging
with cement mortar 1 :2 (1 cement : 2 Coarse sand)
to match the existing floor:
2.35.3.1With Chlorpyriphos/Lindane E.C. 20% with 1%
concentrationSQM 131.90 13.5 1,780.65
CONCRETE WORK
5 4.1.
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering - All work up to plinth level :
4.1.81:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded
stone aggregate 40 mm nominal size)CUM 4,478.15 2.40 10,747.56
6 1.11
Providing and laying damp-proof course 50mm thick
with cement concrete 1:2:4 (1 cement : 2 coarse
sand(zone-III) : 4 graded stone aggregate
20mm nominal size).
SQM 320.25 16.00 5,124.00
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED
DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
CIVIL WORK SECURITY ROOM -2 NOs (3.x4.5 )meter
Page 1 of 5
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR ITEM
2016 Item Description Unit RATE Quantity Amount
CIVIL WORK SECURITY ROOM -2 NOs (3.x4.5 )meter
7 4.17
Making plinth protection 50mm thick of cement
concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) over
75mm thick bed of dry brick ballast 40 mm nominal
size, well rammed and consolidated and grouted
with fine sand, including necessary
excavation, levelling & dressing & finishing the top
smooth.
SQM 450.35 18.00 8,106.30
REINFORCED CEMENT CONCRETE
8 5.1
Providing and laying in position specified grade of
reinforced cement concrete, excluding the cost of
centering, shuttering, finishing and reinforcement -
All work up to plinth level :
5.1.2
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3
graded stone
aggregate 20 mm nominal size).
CUM 6215.35 8.00 49722.80
5.33
Providing and laying in position machine batched and
machine mixed design mix M-25 grade cement concrete
for reinforced cement concrete work, using cement
content as per approved design mix, including pumping
of concrete to site of laying but excluding the cost of
centering, shuttering, finishing and reinforcement,
including admixtures in recommended proportions as
per IS: 9103 to accelerate, retard setting of concrete,
improve workability without impairing strength and
durability as per direction of Engineer-in-charge.“(Note :-
Cement content considered in this item is @ 330
kg/cum.“Excess/ less cement used as per design mix is
payable/recoverable separately).
9 5.33.1 All works upto plinth level cum 6,446.45 8.00 51,571.60
10 5.33.2 All works above plinth level upto floor V level cum 7,250.05 10.00 72,500.50
11 5.35
Add for using extra cement in the items of design mix
over and above the specified cement content therein. Quintal 672.75 15.00 10,091.25
5.9Centering and shuttering including strutting,
propping etc. and removal
of form for all heights :12 5.9.1
Foundations, footings, bases of columns, etc. for
mass concrete.SQM 193.95 120.00 23274.00
135.9.3
Suspended floors, roofs, landings, balconies and
access platformSQM 422.30 140.62 59383.83
14
5.9.5
Lintels, beams, plinth beams, girders, bressumers
and
cantilevers
SQM 342.90 95.00 32575.50
155.9.6
Columns, Pillars, Piers, Abutments, Posts and Struts.SQM 467.85 140.00 65499.00
Page 2 of 5
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR ITEM
2016 Item Description Unit RATE Quantity Amount
CIVIL WORK SECURITY ROOM -2 NOs (3.x4.5 )meter
5.22A
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in position
and binding all complete above plinth level.
165.22A.6
Thermo-Mechanically Treated bars of grade Fe-500 D
or more.KG 56.60 2600.00 147160.00
BRICK WORK
17 6.4
Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level
in all shapes and sizes in :6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) CUM 5582.85 8.34 46574.37
ALUMINIUM WORK
18 21.1
Providing and fixing aluminium work for doors,
windows, ventilators and partitions with extruded
built up standard tubular sections/ appropriate Z
sections and other sections of approved make
conforming to IS: 733 and IS: 1285, fixing with dash
fasteners of required dia and size, including
necessary filling up the gaps at junctions, i.e. at top,
bottom and sides with required EPDM rubber/
neoprene gasket etc. Aluminium sections shall be
smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat
angle, Aluminium snap beading for glazing /
paneling, C.P. brass / stainless steel screws, all
complete as per architectural drawings and the
directions of Engineer-in-charge. (Glazing, paneling
and dash fasteners to be paid for separately)
21.1.1 For fixed portion
21.1.1.2Powder coated aluminium (minimum thickness
of powder coating 50 micron)KG 384.50 450.00 173025.00
19 21.1.2
For shutters of doors, windows & ventilators
including providing and fixing hinges/ pivots and
making provision for fixing of fittings wherever
required including the cost of EPDM rubber /
neoprene gasket required (Fittings
shall be paid for separately)
21.1.2.1
Anodised aluminium (anodised transparent
or dyed to required shade according to IS:
1868, Minimum anodic coating of grade AC 15)
21.1.2.2Powder coated aluminium (minimum thickness
of powder coating 50 micron)KG 444.90 360.00 160164.00
Page 3 of 5
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR ITEM
2016 Item Description Unit RATE Quantity Amount
CIVIL WORK SECURITY ROOM -2 NOs (3.x4.5 )meter
20 21.3
Providing and fixing glazing in aluminium door,
window, ventilator shutters and partitions etc. with
EPDM rubber / neoprene gasket etc. complete as per
the architectural drawings and the directions of
Engineer-in-charge . (Cost of aluminium snap
beading shall be
paid in basic item):21.3.2 With float glass panes of 5.50 mm thickness SQM 1003.95 18.00 18071.10
FLOORING
21 11.26
Kota stone slab flooring over 20 mm (average) thick
base laid over and jointed with grey cement slurry
mixed with pigment to match the shade of the slab,
including rubbing and polishing complete with base
of cement mortar 1 : 4 (1 cement : 4 coarse sand) :11.26.1 25 mm thick SQM 1158.1 12.00 13897.2
22 11.36
Providing and fixing Ist quality ceramic glazed wall
tiles conforming to IS: 15622 (thickness to be
specified by the manufacturer), of approved make, in
all colours, shades except burgundy, bottle green,
black of any size as approved by Engineer-in-Charge,
in skirting, risers of steps and dados, over 12 mm
thick bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and jointing with grey cement slurry @ 3.3kg
per sqm, including pointing in white cement mixed
with pigment of matching shade complete.
SQM 744.8 36.00 26812.80
23.0 11.37
Providing and laying Ceramic glazed floor tiles of size
300x300 mm (thickness to be specified by the
manufacturer) of 1st quality conforming to IS : 15622
of approved make in colours such as White, Ivory,
Grey, Fume Red Brown, laid on 20 mm thick cement
mortar 1:4 (1 Cement : 4 Coarse sand), jointing with
grey cement slurry @ 3.3kg/sqm including pointing
the joints with white cement and matching pigment
etc., complete
SQM 688.35 18.00 12390.30
ROOFING
Page 4 of 5
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR ITEM
2016 Item Description Unit RATE Quantity Amount
CIVIL WORK SECURITY ROOM -2 NOs (3.x4.5 )meter
24 12.55
Providing and fixing Heat Resistant Terrace Tiles (300
mm x 300 mm x 20 mm) with SRI (solar refractive
index) > 78, solar reflection > 0.70 and initial
emittance > 0.75 on waterproof and sloped surface
of terrace, laid on 20 mm thick cement sand mortar
in the ratio of 1:4 (1 cement : 4 coarse sand) and
grouting the joints with mix of white cement &
marble powder in ratio of 1:1, including rubbing and
polishing of the surface upto 3 cuts complete,
including providing skirting upto 150 mm height
along the parapet walls in the same manne
SQM 1150 13.50 15525.00
FINISHING
25 13.4 12 mm cement plaster of mix:
13.4.1 1:4 (1 cement: 4 coarse sand) sqm 180.85 135.00 24414.75
26 13.80
Providing and applying white cement based putty of
average thickness 1 mm, of approved brand and
manufacturer, over the plastered wall surface to
prepare the surface even and smooth complete.
sqm 87.35 135.00 11792.25
27 13.42
Distempering with 1st quality acrylic distemper
(ready mixed) of approved manufacturer, of required
shade and colour complete, as per manufacturer's
specification.13.42.1 Two or more coats on new work sqm 53.15 135.00 7175.25
28 13.60
Wall painting with acrylic emulsion paint of approved
brand and manufacture to give an even shade :
13.60.1 Two or more coats on new work sqm 84.45 135.00 11400.75
29
13.61
Painting with synthetic enamel paint of approved
brand and manufacture to give an even shade :
13.61.1 13.61.1 Two or more coats on new work sqm 78.40 135.00 10584.00
TOTAL 1,084,216.76
SECURITY 2 Nos 2,168,433.51
Page 5 of 5
NRO/CON/ALIMCO-FBD/752/677
SECTION DESCRIPTION AMOUNT (AS PER DSR 2016)
I SANITARY INSTALLATIONS 28307.50
II INTERNAL DRAINAGE 59184.45
III WATER SUPPLY 20945.85
IV EXTERNAL DRAINAGE 44666.60
NET TOTAL COST 153104.40
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND
ASSISTED DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD,
HARYANA
PLUMBING WORKS
NRO/CON/ALIMCO-FBD/752/677
S.NO DESCRIPTION QTY. UNIT RATE AMOUNT
DSR 2016. ITEMS:-
1 17.2
Providing and fixing white vitreous china pedestal
type water closet (European type W.C. pan) with
seat and lid, 10 litre low level white P.V.C. flushing
cistern, including flush pipe, with manually
controlled device (handle lever), conforming to IS :
7231, with all fittings and fixtures complete,
including cutting and making good the walls and
floors wherever required :
17.2.1.W.C. pan with ISI marked white solid plastic seat and
lid2.00 Each 3418.70 6,837.40
2 17.3
Providing and fixing white vitreous china pedestal
type water closet (European type) with seat and lid,
10 litre low level white vitreous china flushing
cistern & C.P. flush bend with fittings & C.I.brackets,
40 mm flush bend, overflow arrangement with
specials of standard make and mosquito proof
coupling of approved municipal design complete,
including painting of fittings and brackets, cutting
and making good the walls and floors wherever
required :
17.3.1W.C. pan with ISI marked white solid plastic seat and
lid2.00 Each 4593.75 9,187.50
3 17.7
Providing and fixing wash basin with CI
brackets,15mm brass pillar taps,32mm CP brass
waste of standard pattern, including painting of
fittings and brackets,cutting and making good the
walls wherever required.
17.7.2White Vitreous China Wash basin size 630x450 mm
with a single 15 mm C.P. brass pillar tap2.00 Each 2020.60 4041.20
4 17.28Providing and fixing P.V.C waste pipe for sink or
wash basin including P.V.C waste fitting complete .
Flexible pipe
17.28.2.2 a) 40 mm dia 10 Each 81.40 814.00
5 17.29Providing and fixing 100mm sand cast iron grating
for gully trap.2 Each 29.25 58.50
6 17.31
Providing and fixing 600x450mm beveled edge
mirror of superior glass (of approved quality)
complete with 6 mm thick hard board ground
fixed to wooden cleats with C.P. brass screws
and washers complete.
2.00 Each 817.95 1,635.90
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR
ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
SUB HEAD I : SANITARY INSTALLATIONS
Plumbing Work
Page 1 of 7
NRO/CON/ALIMCO-FBD/752/677
S.NO DESCRIPTION QTY. UNIT RATE AMOUNT
Plumbing Work
7 17.33Providing and fixing 600 x 120 mm glass shelf with
CP brass brackets and guard rail complete, fixed to
wooden cleadts with CP brass screws.
Each 573.30 -
8 17.34 Providing and fixing toilet paper holder.17.34.1 a) CP Brass 2 Each 385.35 770.70
9 17.60
Providing and fixing trap of self cleansing design
with screwed down or hinged grating with or
without vent arm complete, including cost of cutting
and making good the walls and floors17.60.1 100 mm inlet and 100 mm outlet
17.60.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 159054 Each 677.70 2,710.80
17.60.2 100 mm inlet and 75 mm outlet
17.60.2.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 159052 Each 496.40 992.80
10 17.70Providing and fixing PTMT Bottle Trap for Wash
basin and sink.
17.70.1
Bottle trap 31 mm single piece moulded with height
of 270 mm, effective length of tail pipe 260 mm
from the centre of the waste coupling, 77 mm
breadth with 25 mm minimum water seal, weighing
not less than 260 gms
2 Each 293.95 587.90
11 17.71
Providing and fixing PTMT liquid soap container 109
mm wide,125 mm high and 112 mm distance from
wall of standard shape with bracket of the same
materials with snap fittings of approved quality and
colour, weighing not less than 105 gms.minimum
water seal, weighing not less than 263 gms
2 Each 137.85 275.70
12 17.72
Providing and fixing PTMT towel ring trapezoidal
shape 215 mm long, 200 mm wide with minimum
distances of 37 mm from wall face with concealed
fittings arrangement of approved quality and
colour,weighing not less than 88 gms
2 Each 197.55 395.10
TOTAL (As per DSR. Items) 28,307.50
DSR 2016. ITEMS:-
1 17.35Providing and fixing soil, waste and vent pipes and
rain water pipes conforming to IS 1729.17.35.1 100 mm dia 30.00 Metre 925.55 27,766.50
17.35.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 1590517.35.2 75 mm dia 5.00 Metre 759.80 3,799.00
17.35.2.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905
SUB-HEAD II : INTERNAL DRAINAGE
Page 2 of 7
NRO/CON/ALIMCO-FBD/752/677
S.NO DESCRIPTION QTY. UNIT RATE AMOUNT
Plumbing Work
2 17.36Providing and filling the joints with spun yarn,
cement slurry and cement mortar 1:2 ( 1 cement : 2
fine sand) in S.C.I./ C.I. Pipes :17.36.1 75 mm dia 5.00 Each 72.95 364.75
17.36.2 100 mm dia 30.00 Each 85.95 2,578.50
3 17.37
Providing and fixing M.S. holder-bat clamps of
approved design to sand cast iron/cast iron (spun)
pipe embedded in and including cement concrete
block 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2
coarse sand: 4 graded stone aggregate 20mm
nominal size) including cost of cutting holes and
making good the walls etc.
17.37.1 For 100 mm dia pipe 10.00 Each 167.35 1,673.50
17.37.2 For 75 mm dia pipe 2.00 Each 165.05 330.10
4 17.38Providing and fixing bend of required degree with
access door, insertion rubber washer 3 mm thick,
bolts and nuts complete:17.38.1 100 mm dia 10.00 Each 489.45 4,894.50
17.38.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 1590517.38.2 75 mm dia 2.00 Each 391.05 782.10
17.38.2.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905
5 17.39 Providing and fixing plain bend of required degree.
17.39.1 100 mm dia 10.00 Each 307.10 3,071.00
17.39.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 1590517.39.2 75 mm dia 2.00 Each 212.20 424.40
17.39.2.3 75 mm dia sand cast iron S&S as per 1729
6 17.42.1Providing and fixing double equal plain junction of
required degree.
17.42.1 100x100x100 * 100 mm 5.00 Each 645.10 3,225.50
17.42.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905
7 17.44Providing and fixing single equal plain junction of
required degree.
17.44.1 100x100x100 * 100 mm 5.00 Each 503.40 2,517.00
17.44.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905
8 17.48Providing and fixing single unequal plain junction of
required degree.
17.48.1 100x100x75 mm 2.00 Each 482.45 964.90
17.48.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905 Page 3 of 7
NRO/CON/ALIMCO-FBD/752/677
S.NO DESCRIPTION QTY. UNIT RATE AMOUNT
Plumbing Work
9 17.49Providing and fixing double equal plain invert
branch of required degree.
17.49.1 100x100x100 * 100 mm 2.00 Each 785.60 1,571.20
17.49.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905
10 17.50Providing and fixing single equal plain invert branch
of required degree. 17.50.1 100x100x100 * 100 mm 2.00 Each 503.40 1,006.80
17.50.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905
11 17.56.1 Providing and fixing terminal guard- 100mm 2.00 Each 355.85 711.70
17.56.1.3Hubless centrifugally cast (spun) iron pipes epoxy
coated inside & outside IS: 15905
12 17.57AProviding and fixing shielded coupling for hubless
centrigugally cast iron pipe
17.57.A.1 100 mm dia 5.00 Each 360.50 1,802.50
17.57.A.1.1 SS304 grade coupling with EPDM rubber gasket
17.57.A.2 75 mm dia 1.00 Each 326.00 326.00
17.57.A.2.1 SS304 grade coupling with EPDM rubber gasket
13 17.65
Painting sand cast iron/centrifugally cast (spun) iron
soil, waste vent pipes and fittings with paint of any
colour such as chocolate grey, or buff etc. over a
coat of primer (of approved quality) for new work.
17.65.1 100 mm diameter pipe 30.00 Meter 40.65 1,219.50
17.65.2 75 mm diameter pipe 5.00 Meter 31.00 155.00
TOTAL (As per BSR. Items) 59,184.45
P.W.D. ITEMS:-
1 18.8
Providing and fixing Chlorinate Polyvinyl Chloride
(CPVC) pipes having thermal stability for hot & cold
water supply including all CPVC plain & brass
threaded fittings i/c fixing the pipe with clamps at
1.00 m spacing. This including jointing of pipes &
fittings with one step CPVC solvent cement and the
cost of cutting chases and making good the the
same including testing of joints complete as per
direction of engineer in charge.
SUB HEAD III: WATER SUPPLY
Page 4 of 7
NRO/CON/ALIMCO-FBD/752/677
S.NO DESCRIPTION QTY. UNIT RATE AMOUNT
Plumbing Work
Concealed work oncluding cutting chases and
making good the walls etc.18.8.1 15 mm outer dia pipes. 15.00 Metre 246.20 3,693.00
18.8.2 20 mm outer dia pipes. 20.00 Metre 284.85 5,697.00
2 18.16Providing and fixing brass stop cock of approved
quality complete.18.16.1 15 mm nominal bore 5.00 Each 260.10 1,300.50
18.16.2 20 mm nominal bore 5.00 Each 280.40 1,402.00
3 18.17Providing and fixing gun metal gate valve with C.I.
wheel of approved quality (screwed end):18.17.1 25 mm dia nominal bore 2.00 Each 428.20 856.40
18.17.2 32 mm dia nominal bore 1.00 Each 500.75 500.75
4 1.18.48
Providing and placing on terrace (at all floor levels)
Polyethylene water storage tank ISI : 12701 marked
with cover and suitable locking arrangement amd
making necessary holes for inlet, outlet and
overflow pipes but without fittings and the base
support for tank
400.00 Litre 7.25 2,900.00
5 18.49Providing and fixing C.P.brass bib cock of approved
quality conforming to IS : 8931.8 Each 481.60 3,852.80
6 18.51Providing and fixing C.P.brass long body bib cock of
approved quality conforming to IS standard and
Weighing not less than 690 gms. 18.51.1 15 mm nominal bore. 2 Each 371.70 743.40
7 18.53
Providing and fixing C.P. bass angle valve for basin
mixer and geyser points of approved quality
conforming to I.S:8931 a) 15 mm nominal bore
18.53.1 15 mm nominal bore Each 475.70 -
TOTAL 20,945.85
1 19.4
Providing and fixing square-mouth S.W. gully trap
Class SP-1 complete with C.I. grating brick masonry
chamber with grating brick masonry chamber with
water tight C.I. cover with frame of 300 x300 mm
size (inside) the weight of cover to be not less than
4.50 kg and frame to be not less than 2.70 kg as per
standard design :19.4.2 150x100mm size P type 2.00 Each 1623.25 3,246.50
19.4.2.1With common burnt clay F.P.S (non - modular)
bricks of class designation 7.519.4.3 180x150mm size P type Each 1623.25 -
19.4.3.1With common burnt clay F.P.S (non - modular)
bricks of class designation 7.5
SUB HEAD IV: DRAINAGE- EXTERNAL
Page 5 of 7
NRO/CON/ALIMCO-FBD/752/677
S.NO DESCRIPTION QTY. UNIT RATE AMOUNT
Plumbing Work
2 19.6
Providing and laying non-pressure NP2 class (light
duty) R.C.C. pipes with collars jointed with stiff
mixture of cement mortar in the proportion of 1:2
(1 cement : 2 fine sand) including testing of joints
etc. complete.19.6.1 100 mm dia R.C.C. Pipe 20.00 Metre 325.55 6,511.00
19.6.2 150 mm dia R.C.C. Pipe Metre 356.00 -
19.6.3 250 mm dia R.C.C. Pipe Metre 482.05 -
3 19.70
Constructing brick masonry manhole in cement
mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top
slab with 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size),
foundation in cement concrete 1:4:8 mix (1 cement :
4 coarse sand : 8 graded stone aggregate 40mm
nominal size) inside plastering 12mm thick with
cement mortar 1:3
(1 cement : 3 coarse sand) finished with floating
coat of neat cement and making channels in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20mm nominal size) finished with a
floating coat of neat cement complete as per
standard design :
19.7.1
Inside size 90 x 80 cm and 45 cm deep including C.I.
cover with frame (light duty) 455 x 610 mm internal
dimensions total weight of cover and frame to be
not less than 38 kg (weight of cover 23 kg and
weight of frame 15 kg).
19.7.1.1With common burnt clay F.P.S (non - modular)
bricks of class designation 7.52.00 Each 8634.10 17,268.20
4 19.27
Providing and constructing brick masonry road gully
chamber 50x45x60 cm with bricks in cement
mortar 1:4 (1 cement : 4 coarse sand) including
500x450 mm precast R.C.C. horizontal grating with
frame complete as per standard design.
19.27.1With common burnt clay F.P.S (non - modular)
bricks of class designation 7.52.00 Each 4043.10 8,086.20
Page 6 of 7
NRO/CON/ALIMCO-FBD/752/677
S.NO DESCRIPTION QTY. UNIT RATE AMOUNT
Plumbing Work
5 19.30
Providing and constructing brick masonry chamber
for undergroundCI inspection chamber and bends
with bricks in cement mortar 1:4 (1 cement : 4
coarse sand) C.I. cover with frame (light duty)
455x610 mm internal dimensions, total weight of
cover with frame to be not less than 38 kg (weight
of cover 23 kg and weight of frame 15 kg) R.C.C. top
slab with 1:2:4 mix (1 cement :2 coarse sand : 4
graded stone aggregate 20 mm nominal size)
foundation concrete 1:5:10 (1 cement : 5 fine sand :
10 graded stone aggregate 40 mm nominal size),
inside plastering 12 mm thick with cement mortar
1:3 (1 cement : 3 coarse sand) finished smooth with
a floating coat of neat cement on walls and bed
concrete etc. complete as per standard design :
19.30.1Inside dimensions 455x610 mm and 45 cm deep for
single pipe line :2.00 Each 4777.35 9,554.70
19.30.1With common burnt clay F.P.S (non - modular)
bricks of class designation 7.5
TOTAL 44,666.60
Page 7 of 7
NRO/CON/ALIMCO-FBD/752/677
SUB
HEADDESCRIPTION
AMOUNT (DSR 2018
Items)
(In Rs.)
AMOUNT (NS Items)
(In Rs.)
I POINT WIRING 96,854.00 21,500.00
II DISTRIBUTION BOARDS 12,744.00
III LT CABLE 3,516.00 9,040.00
IV SUPPLY OF LIGHTING FIXTURES 94,600.00
V CCTV SYSTEM 63,800.00
113,114.00 188,940.00
302,054.00 GRAND TOTAL (in Rs.)
SUMMARY SHEET OF ELECTRICAL WORKS
TOTAL (in Rs.)
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED
DEVICES FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR Item
CodeDescription Unit Qty Rate Amount REMARKS
1 1.10
Wiring for light point/Ceiling/Wall fan point
/exhaust fan/call bell point with 1.5 sq.mm
FRLS PVC insulated copper conductor single
core cable in surface/ recessed PVC conduit
with modular switch modular plate suitable GI
box and earthing the point with 1.5 sq.mm
FRLS PVC insulated copper conductor single
core cable etc.as required.
1.10.3 Group C Point 34 990.00 33660.00
2 1.11
Wiring for twin control light point with 1.5
sq.mm FRLS PVC insulated copper conductor
single core cable in surface/ recessed PVC
conduit with 2 way modular switch modular
plate suitable GI box and earthing the point
with 1.5 sq.mm FRLS PVC insulated copper
conductor single core cable etc.as required.
Point 2 1057.00 2114.00
3 1.12
Wiring for light/ power plug with 2X4 sq. mm
FRLS PVC insulated copper conductor single
core cable in surface/ recessed medium class
PVC conduit along with 1 No 4 sq. mm FRLS
PVC insulated copper conductor single core
cable for loop earthing as required.
Mtr. 80 200.00 16000.00
4 1.13
Wiring for light/ power plug with 4X4 sq. mm
FRLS PVC insulated copper conductor single
core cable in surface/ recessed medium class
PVC conduit along with 2 Nos 4 sq. mm FRLS
PVC insulated copper conductor single core
cable for loop earthing as required.
Mtr. 20 308.00 6160.00
5 1.14
Wiring for circuit/ sub main wiring along with
earth wire with the following sizes of PVC
insulated copper conductor, Single core cable
in surface/ recessed PVC conduit as required
a 1.14.2 2x 2.5 sqmm+ 1x 2.5 sqmm earth wire Mtr. 120 167.00 20040.00b 1.14.3 2x 4 sqmm+ 1x 4 sqmm earth wire Mtr. 0 200.00 0.00c 1.14.4 2x 6 sqmm+ 1x 6 sqmm earth wire Mtr. 0 249.00 0.00c 1.14.5 2x 10 sqmm+ 1x 6 sqmm earth wire Mtr. 0 328.00 0.00d 1.14.8 4x 4 sqmm+ 2x 4 sqmm earth wire Mtr. 0 308.00 0.00e 1.14.9 4x 6 sqmm+ 2x 6 sqmm earth wire Mtr. 0 394.00 0.00f 1.14.10 4x 10 sqmm+ 2x 6 sqmm earth wire Mtr. 0 543.00 0.00g 1.14.11 4x 16 sqmm+ 2x 6 sqmm earth wire Mtr. 0 752.00 0.00
6 1.18
Telephone wiring in existing conduiting:
Supply & drawing following pair, 0.5 sq.mm
FRLS PVC insulated copper conductor,
unarmoured telephone cable in existing
surface/ recessed steel/ PVC conduit as
required.a 1.18.2 2 pair Mtrs. 60 20.00 1200.00b 1.18.3 4 pair Mtrs. 0 29.00 0.00
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR ALIMCO AT
NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
ELECTRICAL BOQ
Sub-Head-I : Circuit Cum Point Wiring ( DSR Items)
Page 1 of 3
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR Item
CodeDescription Unit Qty Rate Amount REMARKS
ELECTRICAL BOQ
7 1.21
Supply & fixing of following sizes of PVC conduit
along with accessories in surface / recessed
including cutting the wall & making good the
same in case of recessed conduit as required.
a 1.21.1 20 mm dia. Mtrs. 0 84.00 0.00b 1.21.2 25 mm dia. Mtrs. 40 90.00 3600.00c 1.21.3 32 mm dia. Mtrs. 0 92.00 0.00d 1.21.4 40 mm dia. Mtrs. 0 130.00 0.00e 1.21.5 50 mm dia. Mtrs. 0 158.00 0.00
8 1.24
Supplying and fixing following modular switch/
socket on the existing modular plate & switch
box including connections but excluding
modular plate etc. as required.1.24.1 5/6 A switch Each 4 85.00 340.00
1.24.3 15/16 A switch Each 2 132.00 264.00
1.24.4 3 pin 5/6 A socket outlet Each 4 111.00 444.00
1.24.5 6 pin 15/16 A socket outlet Each 2 175.00 350.00
1.24.6 Telephone socket outlet Each 2 119.00 238.00
1.24.7 TV antenna socket outlet Each 0 119.00 0.00
1.24.8 Bell push Each 0 126.00 0.00
9 1.25
Supplying and fixing two module of Stepped
type electronic fan regulator on the existing
modular plate & switch box including
connections but excluding modular plate etc. as
reqd.
Each 2 342.00 684.00
10 1.26
Supplying and fixing of modular Blanking plate
on the existing modular plate & switch box
including connections but excluding modular
plate etc. as reqd.
Each 4 32.00 128.00
11 1.27
Supply and fixing of following size/ modules, GI
box along with modular base & cover plate for
modular switch/ regulator in recess, including
connection as required.1.27.1 1or 2 module (75mmx 75mm) Each 6 243.00 1458.001.27.1 3 Module (100 mmX75 mm) Each 0 267.00 0.001.27.1 4 Module (125 mmX75 mm) Each 0 287.00 0.001.27.1 6 Module (200 mmX75 mm) Each 0 333.00 0.001.27.1 8 Module (125 mmX125 mm) Each 4 383.00 1532.001.27.1 12 Module (200 mmX150 mm) Each 0 434.00 0.00
12 1.33Supply and fixing of 3 Pin ,5amp ceiling rose on
the existing junction box /wooden block
including connection etc as required.
Each 2 65.00 130.00
13 1.41
Installation, testing & commissioning of pre-
wired, fluorescent fitting / compact fluoroscent
fitting of all type, complete with all accessories
& tubes etc. directly on ceiling / wall, including
connection with 1.5 sq.mm. FRls PVC insulated,
copper condutor, single core cable and earthing
etc. as required.
Each 34 168.00 5712.00
Page 2 of 3
NRO/CON/ALIMCO-FBD/752/677
S.No.DSR Item
CodeDescription Unit Qty Rate Amount REMARKS
ELECTRICAL BOQ
14 1.42
Installation, testing and commissioning of pre-
wired, fluorescent fitting/ compact fluorescent
fitting of all types, with all accessories and tube
etc., including supplying and fixing ball and
socket arrangement, 2 no. down rods of 20 mm
dia X 1.6 mm thick steel conduit upto 30 cm
length, painting and wiring the down rods and
connection with 1.5 sq. mm FRLS PVC insulated,
copper conductor, single core cable and
earthing etc as required.
Each 2 358.00 716.00
15 1.45
Installation, testing & commissioning of ceiling
fan including wiring the down rods of standard
length ( upto 30 cm) with 1.5 sq.mm FRLS PVC
insulated, copper conductor, single core cable,
including providing and fixing phenolic
laminated sheet cover on the fan box etc. as
reqd.
Each 2 203.00 406.00
16 1.49Numbering of ceiling fan/ exhaust fan/
fluorescent fittings as required.Each 34 28.00 952.00
17 1.50
Installation of Exhaust/Wall fan in the existing
opening , including making the hole to suit the
size of the above fan, making good the damage
connection, testing commissioning etc. as
required. 1.50.1 Upto 450 mm sweep Each 2 363.00 726.00
96854.00
1 NSI
Supply, installation, testing and commissioning
of following krone type tag blocks enclosed in
MS enclosure of suitable size with lockable
cover.a 10 pair Tag block No 2 1500.00 3000.00
2 NSI
Supply, laying, testing and commissioning of
following size of 0.6mm dia copper conductor
multi pair telephone cable as per suitable for
indoor telephone wiring conforming for ITD
S/WS - 113 C and S/WS - 114 (actual qty. may
vary as per site) in existing conduit/ trench/
tray.
a5 pair Armoured. Cable (Incoming from BSNL
TAG BLOCK)RM 80 150.00 12000.00
3 NSISupplying, drawing, connecting & testing of 4
pair CAT-6 (E) wire for Data Outlet in existing
conduit
Mtrs. 80 65 5200.00
4 NSISupply, fixing, testing & commisssioning of
Modular RJ-45 with data outlet socket with grid
& cover plate in suitable size of 16 SWG GI box.
Nos 2 650 1300.00
21500.00Total of Sub-Head - I carried to summary sheet (NSI Item)
Total of Sub-Head - II carried to summary sheet (DSR Item)
Sub-Head -I : Circuit Cum Point Wiring (Non Schedule Items)
Page 3 of 3
NRO/CON/ALIMCO-FBD/752/677
S.NO. SR Item Code Description Unit Qty Rate Amount REMARKS
1 2.3
Supplying and fixing following way, single pole
and neutral, sheet steel, MCB distribution board,
240 V, on surface/ recess, complete with tinned
copper bus bar, neutral bus bar, earth bar, din
bar, interconnections, powder painted including
earthing etc. as required. (But without
MCB/RCCB/Isolator)
a 2.3.1 6 way, Double door Each 0 1661.00 0.00
b 2.3.2 8 way, Double door Each 0 1760.00 0.00
c 2.3.3 12 way, Double door Each 2 2053.00 4106.00
2 2.10
Supplying & fixing 5 amps to 32 amps rating 240
volts C curve, Miniature Circuit Breaker suitable
for lighting loads of following poles in the
existing MCB DB complete with connections,
testing and commissioning etc. as required.
a 2.10.1 Single Pole Each 20 199.00 3980.00
3 2.11Supply and fixing single pole blanking plate in
the existing MCB DB complete etc. as required.Each 2.00 8.00 16.00
4 2.14
Supplying and fixing following rating, double
pole, (single phase and neutral), 240 volts,
residual current circuit breaker (RCCB), having a
sensitivity current upto 300 milliamperes in the
existing MCB DB complete with connections,
testing and commissioning etc. as required.
a 2.14.1 25A Each 0 1927.00 0.00
b 2.14.2 40A Each 2 2095.00 4190.00
c 2.14.3 63A Each 0 2640.00 0.00
5 2.21
Providing and fixing M.V. danger notice plate of
200x150mm ,made of mild steel at least 2mm
thick ,vitreous enameled white on both sides
,and with inscription in single red colour on front
side as required.
Each 2.00 226.00 452.00
12744.00
ELECTRICAL BOQ
Sub-Head-II: Distribution Boards (DSR Items)
Total of Sub-Head - II carried to summary sheet (DSR Item)
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR ALIMCO AT
NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
NRO/CON/ALIMCO-FBD/752/677
S.N0.SR Item
CodesDescription Unit Qty Rate Amount
1 7.7 Laying and fixing one Number PVC
insulated and PVC sheathed/XLPE
power cable of 1.1 KV grade of
following size on cable tray as
required.
7.7.1 Upto 35 Sq. mm Meter 80 39.00 3,120.00
2 9.1 Supplying & making of end
terminations with brass compression
gland and Al. lugs for following sizes
of PVC insulated and PVC sheathed/
XLPE Al. conductor cable of 1.1 KV
grade as required.
a) 9.1.1 2 x 6 sq.mm. Each 2 198.00 396.00
3,516.00
1 NSI Supply of following sizes of XLPE/ PVC
insulated Aluminum/ Copper
conductor strip/ wire Armoured,
overall PVC sheathed 1.1 KV grade
cables conforming to relevant IS code
and technical specifications.
1.1 NSI XLPE insulated Al. Ar.Cable
a) 2 x 6 sq.mm. Metre 80 113 9,040.00
9,040.00
.Total of Sub-Head - III carried to summary sheet (NSI Item)
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES
FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
ELECTRICAL BOQ
Sub-Head -III : L.T Cables ( DSR Items)
Total of Sub-Head - III carried to summary sheet (DSR Item)
Sub-Head-VII: L.T Cables (Non- Schedule Items)
NRO/CON/ALIMCO-FBD/752/677
S.NO. Description Unit Qty. Rate Amount REMARKS
Sub-Head - IV: Supply & Fixing of Light Fixtures ( Non DSR Items)
Supply & fixing of following fans & Light
fittings with Electronic Ballast (THD<10%,
HF-P), starter, control gears, lamps holder,
transformer etc. as called for and flexible
wires as required for fixing including
providing of Lamps as required.
1
20 Watt LED TUBE LIGHT Fitting ( 20W
ENDURA LINEAR NEO-MODEL NO-
LHEWEBP6IN1W020 -HAVELLS MAKE or
equivalent)
Each 4 1335.00 5340.00
2
6 Watt LED Light Fitting ( 6W BOLT ROUND
(SURFACE) LED-MODEL NO.-
LHEAARP7UL1W006 - HAVELLS MAKE or
equivalent)
Each 6 1125.00 6750.00
3
30 Watt LED Light Fitting (JETA NEO 30 &
50 LED IP65-MODEL NO.-
LHEPBFUEIN6W030 - HAVELLS MAKE or
equivalent)
Each 20 3850.00 77000.00
4
1200mm sweep 3 blade Ceiling fan
complete with assembling of blades, down
rod, shackle insulator, canopy etc. ( SS-390 -
HAVELLS MAKE)
Each 2 1560.00 3120.00
5Exhaust Fan 250 mm ( VENTIL AIR-DX -
HAVELLS MAKE)250mm Each 2 1195.00 2390.00
94600.00
ELECTRICAL BOQ
Total For Internal Lights
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES
FOR ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
NRO/CON/ALIMCO-FBD/752/677
SUB-V
A. CCTV SYSTEM
1 Bullet cameras
Supply, installation, testing and commissioning of IP
based, 4 MP, FULL HD WDR IR bullet CAMERA - 40
MTRS, colour indoor verifical dome camera, 3.6 MM
FIXED LENS, 1/3 ", 4 Mega Pixel PS CMOS Image Sensor,
WDR (120 dB), Day/ Night (ICR), IR Range of 40 Mtrs,
IP67 and all ancillary equipments and all accessories.
Nos. 4 14000 56000
CP PLUS MAKE - UNC TD40L4-D OR EQUIVALENT IN
OTHER MAKES LIKE SONY/ HONEYWELL.
Network Video Recorder
2 Supply, Installation, Testing and Commisioning of 8
CHANNEL NETWORK VIDEO RECORDER, H.264/MJPEG
dual codec decoding,Max 256 Mbps incoming
bandwidth, HDMI/ VGA simulation video output,
support 8 SATA HDD's upto 32 TB, 1 ESATA up to 16 TB,
supports multi brand network cameras. Each NVR shall
have a storage capacity so as to record a backup for 15
days at 4 CIF @ 25FPS.NVR should have system
expandibility feature of at least 20% of current
requirement, redundant fan and power supplies,
outputs TCPIP network feature & server software
monitor outputs. The NVR should be networkable via IP
protocol & should be able to connect to a web based
system for remote viewing via web system. Vendor
should submit the storage / HDD Calculation.
Nos. 0 45000 0
CP PLUS MAKE - UNR 7364R8-R OR EQUIVALENT IN
OTHER MAKES LIKE SONY/ HONEYWELL.
3 Supplying, drawing, connecting & testing of 4 pair CAT-6
(E) wire for Data Outlet in PVC conduit Mtr. 120 65 7800
TOTAL CARRIED OVER TO SUMMARY V 63800
ESTIMATE FOR PROPOSED CONSTRUCTION OF MANUFACTURING SET UP OF AIDS AND ASSISTED DEVICES FOR
ALIMCO AT NAWADA TIGAON, BALLABGARH, FARIDABAD, HARYANA
CCTV SYSTEM
Sr. No Item Description Unit Qty Rate Amount