tesla electradeteslaelectrade.com/content/documents/a10. siemens 3np... · 2019. 5. 9. · one...
TRANSCRIPT
����������� ������� �������������
���
������
���
�� �����
�����������������
17
Introduction
SENTRON Switching and Protection Devices — Switch Disconnectors
✓ Available
-- Not available
Type 3NP 3K 3NJ4SENTRONRated uninterrupted current Iu At 35 °C ambient temperature A 160 to 630 63 to 1000 160 to 1250Rated operational voltageUe V 690 690 690AC-21At 400 V ✓ ✓ ✓
At 500 V ✓ ✓ ✓
At 690 V ✓ ✓ ✓
AC-22At 400 V ✓ ✓ ✓
At 500 V ✓ ✓ ✓
At 690 V ✓ ✓ ✓
AC-23At 400 V ✓ ✓ --At 500 V -- ✓ --At 690 V -- ✓ --Switch versionsFront mounting -- ✓ --Floor mounting ✓ ✓ --Busbars• 40 mm ✓ -- --
• 60 mm ✓ ✓ --
• 185 mm -- -- ✓
Molded-plastic enclosure ✓ ✓ --Switch accessoriesAuxiliary contacts• 1 NO + 1 NC -- ✓ --
• 1 CO ✓ ✓ ✓
Fuse monitoring• With circuit breakers ✓ ✓ ✓
• With electronics ✓ ✓ ✓
17/3Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors3NP Fuse Switch Disconnectors up to 630 A
General data
17
■ Design
The SENTRON 3NP4 and 3NP5 fuse switch disconnectors comprise a base and a removable fuse carrier with view and measuring window.
The base contains integral lyre-shaped contacts, arcing cham-bers and terminal fittings. The fuse links/isolating links are contained in the fuse carrier.
The fuse links can be replaced without tools.
The three conducting paths in the base and the fuse links in the fuse carrier are separated by partitions that overlap when opening and closing the device.
This type of failsafe protection is called "complete compartmen-talization" and effectively prevents inter-phase arcing.
SENTRON 3NP5 fuse switch disconnectors are also equipped with locating springs, which are fitted to the side of the base. These enable the "high speed closing" of devices, regardless of the actuating speed of the operator.
LV HRC fuses of sizes LV HRC 000 to LV HRC 3 according to IEC 60269-2-1 and DIN VDE 43620 are used in the SENTRON 3NP4 and 3NP5 fuse switch disconnectors. SITOR semiconductor fuses can continue to be used for a wide range of applications.
For more detailed information, please refer to the operating instructions for the SENTRON 3NP4 and 3NP5 fuse switch disconnectors.
Auxiliary switches
The SENTRON 3NP4 and 3NP5 fuse switch disconnectors can also be retrofitted with auxiliary switches for indicating the switch position of the fuse carrier.
One switch block (1 CO) can be mounted on size LV HRC 000 of the SENTRON 3NP4 fuse switch disconnector and two switch blocks (1 CO) can be mounted on sizes LV HRC 00 to LV HRC 3.
SENTRON 3NP5 fuse switch disconnectors can also be deliv-ered with a 2-pole auxiliary switch (1 NO + 1 NC) if required. The version with fuse monitoring is fitted with this auxiliary switch as standard.
■ Function
Fuse monitoring by SIRIUS circuit breaker
For fuse monitoring, a SIRIUS circuit breaker is factory-fitted and hard-wired to the fuse carrier of the SENTRON 3NP4 and 3NP5 fuse switch disconnectors.
If the fuse carrier is closed, the three conducting paths of the SIRIUS circuit breaker are switched in parallel to the fuse links to be monitored. If the fuse carrier is open, all main current paths of the circuit breaker are off circuit.
The internal resistance of the circuit breaker is great enough not to impair the protective function of the monitored fuse links.
Failure of a fuse will trigger the circuit breaker. The auxiliary switch of the circuit breaker can be used for indication purposes or to disconnect the main circuit, e.g. through a contactor.
The signal cable for the SENTRON 3NP4 fuse switch disconnec-tor size LV HRC 00 needs to be ordered separately. For sizes LV HRC 1 to LV HRC 3 the connection is via flat connectors.
Delivery of the SENTRON 3NP5 fuse switch disconnectors includes the signal cable, complete with connector.
SIRIUS circuit breakers cannot be used for fuse monitoring in branch circuits by circuit breakers where a fault may result in > 220 V DC feedback.
In the case of parallel cables and meshed systems, only a voltage difference of > 24 V at the switch will trigger the circuit breaker.
Electronic fuse monitors
For electronic fuse monitoring, the EF monitor is factory-fitted and hard-wired to the fuse carrier of SENTRON 3NP5 fuse switch disconnectors.
The EF monitor works independently of any loads. Failure of a fuse can be relayed to a control room through integrated auxiliary switches (2 NO + 1 NC) by means of a centralizedfault indication or used to isolate the load through e.g. a contactor.
Actuation of the auxiliary switch depends on the EF monitor. Version "A" stands for "open-circuit principle", version "R" for closed-circuit principle" (see schematic circuit diagram on page 17/44).
If a fuse is tripped, a green LED signal flashes (general fault) and the location of the failed fuse is indicated by a red LED. Using more than one device facilitates identification of the affected branch circuit.
The EF monitor is automatically reset to the standby position once the faulty fuses are replaced. This state is indicated visually by the status display (green LED).
The EF monitor is also suitable for operation in industrial networks badly afflicted by harmonics.
17/32 Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors
17
3NP Fuse Switch Disconnectors up to 630 A
General data
■ Technical specifications
1) 125/160 A only with 3NY1 236 feeder terminals and with 3NY1 822 (125 A) and 3NY1 824 (160 A) 21 mm wide fuse links; see accessories.
2) When switching without load (AC-20 B, DC-20 B), direct voltages up to 690 V DC can be applied.
3) For safety monitoring max. 690 V.4) For degree of pollution 2, the switch disconnectors can be used up to
1000 V AC-20 B, DC-20 B (no-load switching).5) Conducting paths in series: 3 for 3NP40; 2 for 3NP42, 3NP43 and 3NP44.
Standards IEC 60947-1, IEC 60947-3, VDE 0660 Part 107Type 3NP40 1 3NP40 7 3NP42 7 3NP43 7 3NP44 7Rated uninterrupted current Iu A 1601) 160 250 400 630For fuse links according to DIN 43620 Size 00C/000 00 1 and 0 2 and 1 3 and 2
Continuous thermal current Ith A 1601) 160 250 400 630Rated operational voltage UeAC 50 Hz/60 Hz V 690 690DC V 220
(3 conducting paths series-connected)
440 (2 conducting paths series-connected)
Rated insulation voltage Ui V 690 690 8003) 8003) 8003)
Rated impulse voltage Uimp kV 6 6 6 6 6Rated conditional short-circuit current with fuses (for fast switch-on)With fuse linksRated current Size/A 000/100 (35) 00/160 1/250 2/400 3/630At 400 V AC (690 V) kA
(rms value)
50 (50) 50 50 50 50
Maximum permissible let-through I2t value kA2s 56 (7.8) 158 551 1515 4340Permissible let-through current of the fuse kA
(peak value)
11 (5) 15 25 35 55
Short-circuit strength with fuses(with closed switch)With fuse linksRated current Size/A 000/100 00/160 1/250 2/400 3/630At 690 V kA
(rms value)
100 50 50 50 50
Permissible let-through current of the fuse kA (peak value)
15 15 25 35 55
Rated making and breaking capacity (infeed from top or bottom)At 400 V AC, with fuse links or isolating links
Size 000 00 1 2 3
Rated breaking current Ic (p.f.= 0.35) A (rms value)
800 (p. f. = 0.45)
800 2000 3200 5040
Rated operational current Ie for AC-21B, AC-22B, AC-23B
AA
160100
160100
250250
400400
630630
At 500 V AC, with fuse links or isolating links
Size 000 00 1 2 3
Rated breaking current Ic (p.f.= 0.35) A (rms value)
320 (p. f. = 0.45)
320 750 1200 1890
Rated operational current Ie for AC-21B, AC-22B, AC-23B
AAA
16010040
16010040
250250--
400400--
630630--
At 690 V AC, with fuse links or isolating links
Size 000 00 1 2 3
Rated breaking current Ic (p.f.= 0.35) A (rms value)
200/240 (p. f. = 0.45/0.95)
200/240 (p. f. = 0.45/0.95)
375 600 945
Rated operational current Ie for AC-21B, AC-22B, AC-23B
AAA
1605025
1605025
250----
400----
630----
At 220 V/240 V DC, with fuse links2)4)5) or isolating links
Size 000 00 1 2 3
Rated operational current Ie at 220 V DC-23B/DC-21B440 V DC-21B
AA
80/160--
80/160--
--250
--400
--630
17/33Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors3NP Fuse Switch Disconnectors up to 630 A
General data
17
1) Only with isolating links; otherwise, please observe specifications of fuse manufacturer.
Standards IEC 60947-1, IEC 60947-3, VDE 0660 Part 107Type 3NP40 1 3NP40 7 3NP42 7 3NP43 7 3NP44 7Capacitor switching capacityAt 400 V ACCapacitor rating kvar 50 50 -- -- --Rated current In A 72 72 -- -- --
At 525 V ACCapacitor rating kvar 50 50 -- -- --Rated current In A 55 55 -- -- --
Permissible ambient temperature °C -25 ... +551) for operation, -50 ... +80 when storedMechanical endurance Operating
cycles2000 2000 1600 1000 1000
Degree of protection (operator side)Without molded-plastic masking frame/cable lug cover IP00 (3NP40 with box terminal and properly connected conductors: IP20)With molded-plastic masking frame/cable lug cover IP30 (switch closed), IP20 (switch open)Power loss of the switch disconnector at Ith (plus power loss of the fuse links)Without busbar adapter W 4.5 (at 100 A) 10 15 30 47With busbar adapter W 8.5 (at 100 A) 20 47 83 127Main conductor connectionsFlat connector for cable lug, max. conductor cross-section (stranded)
mm2 -- Up to 2 × 70 (M8)
Up to 150 (M10)
Up to 240 (M10)
Up to 2 × 240 (M12)
Box terminal/terminal (finely stranded with end sleeve)
mm2 1.5 ... 50 (35) 2.5 ... 70 (50) 70 ... 150 120 ... 240 150 ... 300
Busbar (width × thickness) mm -- 22 × 5 22 ... 30 × 5 ... 10
22 ... 30 × 5 ... 10
25 ... 40 × 5 ... 10
Louvered Cu strips, unperforated in terminals (width x thickness)
mm 8 × 8 Up to 9 × 8 Up to 16 × 8 Up to 20 × 10 Up to 24 × 10
Tightening torques for terminal screwsFor flat connector Nm -- 10 ... 12 25 25 30With SIGUT box terminal/terminal Nm 3 ... 3.5 8 ... 10 6 8 8Auxiliary switch 1 CO (accessories)3NY3 035 50 Hz/60 Hz up to 230 V AC Rated operational current Ie at AC-14 A 0.25 (Ith = 5 A), at 24 V DC: Ie = 0.45 A; flat terminations according to DIN 46244:
A 2.8 × 0.53NY3 030 50 Hz/60 Hz up to 230 V ACRated operational current Ie at AC-13 A 0.1 (Ith = 0.1 A); plug-in sleeve according to DIN 46245: A 2.8 ... 1Permissible mounting positions Vertical or horizontal installation (no reduction of specified switching capacity)
17/34 Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors
17
3NP Fuse Switch Disconnectors up to 630 A
General data
1) When observing degree of pollution 2 (instead of 3) operation is also possible up to Ui = 1000 V.
2) Rated making and breaking current according to IEC 60947-3Rated making current I = 10 × Ie (AC-23); 3 × Ie (AC-22);1.5 × Ie (AC-21)Rated breaking current Ie = 8 × Ie (AC-23); 3 × Ie (AC-22);1.5 × Ie (AC-21)
3) When using electronic fuse monitoring, infeed must be from the top.
Standards IEC 60947-1, IEC 60947-3, VDE 0660 Part 107
Type 3NP50 3NP52 3NP53 3NP54Rated uninterrupted current Iu A 160 250 400 630 For fuse links according to DIN 43620 Size 00 1 and 0 2 and 1 3 and 2(when SITOR semiconductor fuse links are used, a reduction of rated current is necessary, see Catalog SITOR Configuration, Order No. E20001–A700–P302)
Conventional free-air thermal current Ith A 160 250 400 630Rated operational voltage UeAC 50 Hz/60 Hz V 690DC V 440 (3 conducting paths series-connected),
220 (2 conducting paths series-connected and with fuse monitoring through 3RV)
Rated insulation voltage Ui V 6901) 6901) 6901) 6901)
Rated impulse voltage Uimp kV 6 6 6 6Rated conditional short-circuit current with fuses (for fast switch-on)With fuse linksRated current Size/A 00/160 1/250 2/400 3/630At 500 V AC kA
(rms value)
50 50 50 50
Permissible let-through current of the fuses kA (peak value)
15 25 40 50
Short-circuit strength with fuses (with closed switch)With fuse linksRated current Size/A 00/160 1/250 2/400 3/630At 500 V AC kA
(rms value)
100 100 50 50
Maximum permissible let-through I2t value kA2s 223 780 2150 5400Permissible let-through current of the fuses kA
(peak value)
23 32 40 60
Rated short-circuit making capacity with isolating links2) Size 00 1 2 3At 500 V AC kA
(peak value)
6 17 17 17
Rated making and breaking capacity2) (infeed from top or bottom)3)
Size 00 1 0 2 1 3 2At 400 V AC, with fuse linksBreaking current Ic (p.f. = 0.35) A
(rms value)
1600 2500 1600 4000 2500 5040 4000
Rated operational current Ie at AC-21B, AC-22B, AC-23B
A 160 250 160 400 250 630 400
At 500 V AC, with fuse linksBreaking current Ic (p.f. = 0.35) A
(rms value)
1300 2500 1600 4000 2500 5040 4000
Rated operational current Ie at AC-21B, AC-22B, AC-23B
A 160 250 160 400 250 630 400
At 690 V AC, with fuse linksBreaking current Ic (p.f. = 0.35) A
(rms value)
800 1280 1000 2520 1600 3200 2520
Rated operational current Ie for AC-21B, AC-22B, AC-23B
AA
160100
250160
160125
400315
250200
630400
400315
At 220 (440) V DC, with 2 (3) conducting paths series-connected and fuse linksBreaking current Ic (L/R = 15 ms) A 640 1000 640 1600 1600 2520 1600Rated operational current Ie at DC-23B A 160 250 160 250 250 630 400
17/35Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors3NP Fuse Switch Disconnectors up to 630 A
General data
17
1) Insert silver-plated isolating links.
Standards IEC 60947-1, IEC 60947-3, VDE 0660 Part 107
Type 3NP50 3NP52 3NP53 3NP54Switching capacity with isolating links1)
(infeed from top or bottom)At 400 V AC, with isolating links Size 00 1 2 3Breaking current Ic (p.f. = 0.35) A
(rms value)
1600 2500 2500 4000
Rated operational current Ie for AC-21B, AC-22B, AC-23B
AA
160160
250250
400315
630500
At 500 V AC, with isolating linksBreaking current Ic (p.f. = 0.35) A
(rms value)
1300 2500 2500 4000
Rated operational current Ie for AC-21B, AC-22B, AC-23B
AA
160160
250250
400315
630500
At 690 V AC, with isolating linksBreaking current Ic (p.f. = 0.35) A
(rms value)
800 1280 1600 2520
Rated operational current Ie for AC-21B, AC-22B, AC-23B
AA
160100
250160
400200
630315
At 220 V DC, with isolating linksBreaking current Ic (L/R = 15 ms) A 640 1000 1600 1600Rated operational current Ie at DC-23B A 160 200 400 400
Switching capacity for horizontal installation Up to 690 V AC-22B
No reduction in specified switching capacity (values for AC-23B up to 690 V on request)
17/36 Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors
17
3NP Fuse Switch Disconnectors up to 630 A
General data
1) When using isolating links. If using fuse links, please observe specifications of fuse manufacturer.
2) For 3NP52 with terminal clamp connection, degree of protection IP10.3) With busbar adapter.
Standards IEC 60947-1, IEC 60947-3, VDE 0660 Part 107Type 3NP50 3NP52 3NP53 3NP54Capacitor switching capacityAt 400 V ACCapacitor rating kvar 80 90 150 250Rated current In A 116 130 216 361
At 525 V ACCapacitor rating kvar 100 125 200 300Rated current In A 110 137 220 330
Permissible ambient temperature °C -25 ... +55 for operation1), -50 ... +80 when storedMechanical endurance Operating
cycles1600
Degree of protectionWithout molded-plastic masking frame IP002)
With molded-plastic masking frame andclosed fuse carrier on the operator side IP30with open fuse carrier IP10
Power loss of of the switch disconnector at Ith(plus power loss of the fuse links) Without busbar adapter W 7.8 (16.3)3) 7.5 15 39
Main conductor connectionsCable lug, max. conductor cross-section (stranded) mm2 2.5 ... 120 6 ... 150 6 ... 240 6 ... 2 × 240Busbar mm 16 ... 22 22 ... 30 22 ... 30 22 ... 30Terminal clamp mm2 2.5 ... 50 35 ... 120 -- --
Tightening torqueWith cable lug Nm 18 ... 22 25 ... 30 25 ... 30 25 ... 30With busbar Nm 18 ... 22 25 ... 30 25 ... 30 25 ... 30With terminal clamp Nm 9 ... 11 5 ... 6 -- --
Terminal screwsWith cable lug M8 M10 M10 M10With busbar M8 M10 M10 M10With terminal clamp M8 2 × M6 -- --
PE/ground terminalsCable lug according to DIN 46234 mm2 -- 2.5 ... 70 6 ... 2 × 70 6 ... 2 × 120Busbar mm -- 25 25 30Terminal screws -- M8 M10 M10
Auxiliary switch 1 NO + 1 NC (accessories) (the same voltage potential must be applied to both NO and NC contact)At 50 Hz/60 Hz up to 400 V AC, rated operational current Ie at AC-12/AC-15 A
A 16/6
Flat connector (DIN 46244) A 6.3 ... 0.8Permissible mounting positions Vertical or horizontal
(partially reduced switching capacity with horizontal mounting)Fuse monitoring with 3RV motor starter protectors See circuit breakerElectronic fuse monitoringRated voltage 50 Hz/60 Hz AC V 400 -15% ... 500 V +10%, self-powered (infeed from top)Max. inrush current A 20Uninterrupted current A 5Breaking current A 5
Switching capacity VA 1000Short-circuit strength (1 ms) A 100Response time s < 1Temperature range (operation) °C -10 ... +75Plug-in connectors/connections 6-pole
Minimum required potential difference between upper and lower switch connections (e.g. for use in meshed systems)
V >10
Signaling contact for electronic fuse monitoring
2 NO + 1 NC
Rated operational current IeAt 250 V, DC-13 A 0.27At 240 V, AC-15 A 1.5
Thermal free-air rated current IthA 5
17/37Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors3NP Fuse Switch Disconnectors up to 630 A
For power distribution
17
■ Dimensional drawings
3NP40 10 Cut-outfor 3NP35 and 3NP40 10
3NP40 10with 3NY1 995 quick retaining plate mount-ing rail center-to-center clearance 125 mm
3NY1 995 quick retaining plate for 3NP40 10 and 3NP40 70
3NP40 10 with 3NY1 237 3-phase busbar for 2 fuse switch disconnectors
3NY1 265 covering cap for 3NY1 2383-phase busbar
3NP40 10 with 3NY1 235 triple terminal
3NP40 10 with 3NY1 236 supply terminal
3NP40 10 with 3NY1 251 molded-plastic masking frames
3NP40 15-1CJ01 with busbar adapter, flat, rails of width 12 mm or 15 mm and thickness 5 mm or 10 mm, bottom connection
3NP40 15-1CK01with busbar adapter, flat, rails of width 12 mm or 15 mm and thickness 5 mm or 10 mm, bottom connection
3NP40 15-0CJ01with busbar adapter, deep, rails of width 12 mm or 15 mm and thickness 5 mm or 10 mm, bottom connection
3NP40 16-1CJ01 with busbar adapter, rails of width 12, 15, 20 mm or 30 mm and thickness 5 mm or 10 mm, flat, T, double-T profiles and other renowned busbar systems, bottom connection
3NP40 16-1CK01 with busbar adapter, rails of width 12, 15, 20, 25 mm or 30 mm and thickness 5 mm or 10 mm, flat, T, double-T profiles and other renowned busbar systems, top connection
� � � �� �
�����
���� ����
� � � � � � � �
� � � � �
� �� �
��
� � �
�
���
�����
� � �
� �
�����
� � � � � � � � � � � � � � � �
���
��
���
��
�
��
�
�
��
��
��
��
�
�
�����
��
�
��
��
��
���
��
������
�
�
�
��
��
�
��
��
��
��
�
��
��
��
� ��
����
��
��
��
��
Top holes with a 50 mm intermediate dimension must be used for installation in STAB 8GDwall-mountingdistribution boards.
�
��
��
��
�
�� ��
��
��
�
���� ���
��
��
������
�
��
��
��
�
���
��
��
��
�
��
��
�
�
��
��
���� �� ���
��
��
��
��
���� ��
���
��
��
���
��������
��
��
��
�
��
����
� ��
�� �����
�
��
���
��
���� �������
��
��
��
��
��
��
���
��
��
�
�� �����
�
��
���
��
���� ���� �
��
��
��
��
��
��
���
��
��
���
��
�
��
��
�
�
���� ����
��
��
��
��
���
��
��
�� �����
��
��
���
��
�
��
���
��
���� ����
��
��
��
��
��
���
��
��
����
�� �����
��� �
89
NS
E 0
0205
a
25,5 25,5
1060
6016
811
,5
7214
69,519 100,5
201
17/38 Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors
17
3NP Fuse Switch Disconnectors up to 630 A
For power distribution
1) h = distance from upper edge of panel cut-out to center of disconnector mounting.
2) Cover is placed open on the switchgear cabinet panel, for cover behind control cabinet panel: cut-out dimensions on request.
3NP40 70 for mounting
3NP42 70, 3NP43 70, 3NP44 70 for mounting
Drilling pattern for 3NP40 70
3NP40 75-0 with busbar adapter, deep, rails of width 12 mm or 15 mm and thickness 5 mm or 10 mm
3NP40 75-1 with busbar adapter, flat, rails of width 12 mm or 15 mm and thickness 5 mm or 10 mm
For metal framesCut-outs for 3NP4
NS
E00
206a
108
83
,517
17
0
45 36,516
1
190
50
70
10
1
NS
E0_
0020
7a
dc
eb
a
f f
Type a b c d e f3NP42 70 184 243 66 45.5 215 573NP43 70 210 288 80 48 255 653NP44 70 256 300 94.5 48 267 81
��������
198
11
114
116
157
274,
4
130
25
50
NS
E00
523
118
5,8
5070 11
019
5
For plastic framesCut-outs2)
for 3NP40 70
Cut-outs2)
for 3NP42
NS
E00
525
224
174
���
130
50
11
NS
E00
526
270
177,
526
7
162
50
11
Cut-outs2)
for 3NP43Cut-outs2)
for 3NP44
NSE0052
122,5
M 685
81,7
97,5
���
���
��
���
���
�
��
�
�
��
��
����� �
��
��
��
��������
�
��
��
��
����������
�
3NY73 22 quick retaining plate
Drilling pattern for 3NP42 70
Drilling pattern for 3NP43 70 Drilling pattern for 3NP44
$ Bottom edge disconnector-base % Center disconnector-base
�
�
��
��
��
�
��
��
�����
�
�
�
��
��
�� ���
��
���
��
��
��
�
���
��
�
�
�
��
��
�
���
�
�����
�
�� ���
��
���
��
��
��
�
���
��
�
�
�
��
�
��
Type Cover between installation kit
Panel cut-out min.
Molded-plastic masking frame behind panelType B H B H h1)
3NP40 1 3NY1 251 130 215 100 180 1003NP40 7 3NY7 200,
3NY7 201130 215 118 195 110
3NP42 7 3NY7 220 220 375 210 275 1573NP43 7 3NY7 230 245 375 235 315 1743NP44 7 3NY7 240 290 375 280 325 178
Molded-plastic masking frame in front of panelType B H B H h1)
3NP40 1 3NY1 251 130 215 100 155 873NP40 7 3NY7 200,
3NY7 201130 215 118 195 110
3NP42 7 3NY7 220 220 375 198 275 1573NP43 7 3NY7 230 245 375 224 315 1743NP44 7 3NY7 240 290 375 270 325 178
�
��
���
��
�
�
�
17/39Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors3NP Fuse Switch Disconnectors up to 630 A
For power distribution
17
1) For VBG4 plus dimension c of the cable lug covers (see page 17/41).2) The 3NY7 820 molded-plastic masking frame is used for depth
compensation (below) when installed together with size 000 or size 00 in STAB/SIKUS distribution boards.
3NP40 70-0F for mounting and installation
3NP40 75-0F with busbar adapter, deep, 40 mm, rails of width 12 mm or 15 mm and thickness 5 mm or 10 mm
3NP40 75-1F with busbar adapter, flat, 40 mm, rails of width 12 mm or 15 mm and thickness 5 mm or 10 mm
3NP40 76-0F with busbar adapter, flat, 60 mm, rails of width 12 mm or 30 mm and thickness 5 mm or 10 mm
3NP40 76-1 with busbar adapter, busbars with a width of 12 mm to 30 mm and a thickness of 5 mm or 10 mm, flat, T and double-T profiles
3NP42 75-1 3NP42 76-1 3NP43 76-1 3NP44 76-1
with busbar adapter, busbars with a width of 12 mm to 30 mm and a thickness of 5 mm or 10 mm,flat, T and double-T profiles
�����������
� � �
� � � � � � �
����
��
��
� �
��
���
���
��
���
���
���
�
�
�
���
�
�
�����
���
��
���
���
��
���
�
�
��
����� ��
���
���
�
��
��
��
���
�
�
�
��
�
�
�
�
��
��
�
��
��
��
�
�
��
��
����
��
��
Type a b1) c d e f3NP42 75-1 184 243 832) 45.5 111 403NP42 76-1 184 243 832) 45.5 111 603NP43 76-1 210 288 97 48 125 603NP44 76-1 256 300 112 48 139 60
17/40 Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors
17
3NP Fuse Switch Disconnectors up to 630 A
For power distribution
3NY7 200 molded-plastic masking frame for 3NP40 7 for installation in any distribution board
3NY7 201 molded-plastic masking frame for 3NP40 7.- for 3NP40 7.-CA01
3NY7 220 molded-plastic masking frame for 3NP42 for installation in any distribution board
3NY7 230 molded-plastic masking frame for 3NP43 for installation in any distribution board
3NY7 240 molded-plastic masking frame for 3NP44 for installation in any distribution board
3NY7 820 molded-plastic masking framefor one 3NP42 70 switch disconnectorfor installation in STAB/SIKUS distribution boards
3NY7 500 molded-plastic masking framefor one 3NP40 switch disconnector, left, for installation in SIKUS 3200, STAB 160 and 400 and SIKUS 630 distribution boards
3NY7 501 molded-plastic masking framefor one 3NP40 switch disconnector, right, for installation in SIKUS 3200, STAB 160 and 400 and SIKUS 630 distribution boards
3NY7 502 molded-plastic masking framefor two 3NP40 switch disconnectors for installation in SIKUS 3200, STAB 160 and 400 and SIKUS 630 distribution boards
3NY7 600 touch protection cover for installation in ALPHA distribution boardsfor 3NP40 76 switch disconnectors
3NY7 601 touch protection coverfor 3NP40 75, 3NP40 76switch disconnectors
Cable lug cover for 3NP40 7 with flat connector, 3NY7 101
Cable lug cover for 3NP42 to 3NP44, 3NY7 121, 3NY7 131, 3NY7 141
������ ��
��
�
NS
E00
527
130
215
40
�������
���
��
���
�������
���
����
���������
���
���
���
��������
�
�
���
��
��
��
��
�
���
���
�
�
��
��
��
��
���
���
�
�
�����������
� � �
� �
���
112 32
73
38
5
19
5NS
E0
_0
16
05
112
38
2
14
2
19
4NS
E0
_0
16
04
73
123
��
�����
������
�� ��
��
������
Type a b c3NY7 121 181 65 673NY7 131 207 79 503NY7 141 253 94 47
17/41Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors3NP Fuse Switch Disconnectors up to 630 A
For extended technical requirements
17
■ Dimensional drawings
1) h = distance from upper edge of panel cut-out to center of disconnector mounting.
2) With standard molded-plastic masking frame behind the control panel and corresponding control panel cut-out, the specified switching capacity is reduced to the following AC 23B values: at 400 V Ie 160 A, at 500 V from Ie 160 A to 125 A and at 690 V from Ie 100 A to 50 A.
3NP50 60, 160 A for mounting
3NP50 60, 160 A with molded-plastic masking frame for any type of installation
3NY1 107 molded-plastic masking frame
3NP50 60, 160 A with fuse monitoring by 3RV1 motor starter protector, with plug-in connection
For plastic frames Cut-out for 3NP50 60, with and without auxiliary switch
Cut-out for 3NY1 208 mounting kit
For metal framesCut-outs for 3NP5
116 1517
397
19663
6384
70
36 36134
22M8 3416
531
97,5
19
NS
E00
226
Ø5,8
228Auxiliary switch Type a b c d
3NY1 105 135 215 95.5 383NY1 115 135 215 95.5 383NY1 106 135 290 144.5 643NY1 108 135 290 144.5 643NY1 208 149 250 115 53.5
��
�
������
�� �
��
���
�����
�����
���
��
������
���
���
�����
���
������
���
��
���
���
�����
������
NS
E00
230
126,5
191
207,
5
6143
Type Cover between installation kit
Panel cut-out min.
Molded-plastic masking frame behind panelType B H B H h1)
3NP50 6 3NY1 1052) 135 215 130 206 1153NP50 6 3NY1 1253NP52 6 3NY1 210 222 300 210 293 1463NP53 6 3NY1 211 245 300 235 293 1463NP54 6 3NY1 212 290 300 280 293 146
Molded-plastic masking frame in front of panelType B H B H h1)
3NP50 6 3NY1 105 135 215 130 205 1153NP50 6 3NY1 208 149 250 143 191 --3NP52 6 3NY1 210 220 300 210 262 1323NP53 6 3NY1 211 245 300 234 262 1323NP54 6 3NY1 212 290 300 279 262 132
�������
�
��
17/42 Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors
17
3NP Fuse Switch Disconnectors up to 630 A
For extended technical requirements
3NP5. 60, 250 to 630 A for mounting
3NP5. 60, 250 to 630 A with molded-plastic masking frame, for installation
3NP5. 60, 250 to 630 A with fuse monitoring by 3RV motor starter protector, with plug-in connection
3NP50 65, 160 A with busbar adapter, with fuse monitoring by 3RV motor starter protector, with plug-in connector
3NP50 65, 160 A with busbar adapter, rails of width 12 mm and thickness 5 mm or 10 mm
3NP5. 60, 160 to 630 A with electronic fuse monitoring, with plug-in connection and control cable
3NP50 60, 160 A with electronic fuse monitoring, with plug-in connection and control cable
3NP5. 60, 250 to 630 A with electronic fuse monitoring, with plug-in connection and control cable
��
��
��
������
���
���
� ��
��
� ���
� ��
�
�����
�
�� �
!
Cut-out for 3NP52 60, 3NP53 60 and 3NP54 60
1) Through hole for screw
Type a b c d e f g h I3NP52 60 207 202 130 93 62 176 38 41 11.53NP53 60 231 226 130 106 70 192 39 39 11.53NP54 60 276 271 200 111 85 207 40.5 40.5 11.5
k1) l1) m N o q r s t3NP52 60 M10 M8 336 25 32 212 3.6 156 2103NP53 60 M10 M10 352 25 25 228 4.4 180 2343NP54 60 M10 M10 367 30 25 243 6 225 279
u w x y3NP52 60 89.5 220 186.5 200.53NP53 60 105.5 245 202.5 216.53NP54 60 120.5 290 217.5 231.5
� � � � � � � � � � �
���
�
� �
�
� �
���
�
�
��
������
�
���
�
�
� �
���������
�
�
������
���
�����
��
������ ���
�
���
�� ��
��
���
�������
���
����
���
��
�� ��
�
���
��
� ��
����
���
� ��
��
���
������
���
���
�������
� �
���������
���
�
�
17/43Siemens LV 1 T · 2007
3NP, 3NJ4, 3NJ5 Fuse Switch Disconnectors3NP Fuse Switch Disconnectors up to 630 A
For extended technical requirements
17
■ Schematics
SENTRON 3NP fuse switch disconnector with fuse monitoring (with 3RV1 motor starter protector, with auxiliary switch 1 NO + 1 NC)
SENTRON 3NP5 fuse switch disconnector with electronic fuse monitoring
Function for auxiliary contacts – main contact elements with SENTRON 3NP4 and 3NP5
��
�� � �� �� �� ���
��
�� ��
� � �� �� �� �
������ ��
� � �� �� �� ��
��
� ���
��������������
��������� ��
!�"��#����
�����#�$
%&�'�'�"���('��)
� ���
!�"��#�
�*�
�*�
�#�����
�#�$
+���,
+���,
+���,
��*��
��*��
�#�����
+���,
+���,
+���,
��*��
��*��
�#�����
�#�����
�#�����
+���,
+���,
+���,
+���,
+���,
Circuit diagram of main circuit Circuit diagram of auxiliary circuit
Q1 = Fuse switch disconnectorQ2 = Motor starter protectorK1 = ContactorS1 = ON buttonS0 = OFF pushbuttonF1 = Overload relayF2 = Control-circuit fuse
� �� �� �
� �
� �
� �
� �
� � � �
� �
� �
� �
� �
� � � � � �
� � �
� �
�
�
��� �
� �
�� �
� � � � � � � � � �
� � � � � � � � � � � � �
�� �������������
�
�
�
� ��
��� �
�������
��
��
Schematic circuit diagram
�
�� � � � �� ��
� � � �
�� �� �� �� ����
��
�� � ��
� �
��� � � ���
�������
�� !"#$%"$&'#$(()# *!'"+!&,�-'�,)
.$*)#�-/00(1/&!'
�$('�,)-
1&"+#$&!%��'!$&�-!,&�(-
�/('��
�/('�
�/('��
�)-!-'$#
&)'*$#2
.�#�3)')#!��'!$&
!,&�(�(!&)-
����4!-0(�1
�/&&!&,
Version "A" (open-circuit principle): auxiliary switches only pick up if fuse faulty and voltage is applied. Version "R" (closed-circuit principle): auxiliary contacts pick up as soon as voltage is applied and as long as fuses are intact.
17/44 Siemens LV 1 T · 2007
���������������� �����
����������
������������ ������������������ ��������� ������������������� !"#$%&$'(&))(&*�$+
���,������,���-���������
��������� ������������� ������ ������ ����������� ��������� ��� ��������������������������������� ����������� ���������������������������������������������������� ����� ������������ �� ������� ����������� ��� ������� �������� ��������� ��� ����������������� ���������������������� ��� �������� �� ������������ ����� ������������������ ������������� � ���������� �� �� ����
�������� �������� ����������� ������������� ������������������������������������������������� ������ ������ ���������������������� �� ������ ���� ��������
.��/��������������
���0
�� �����1���0�2�" 314) 3 #" ,.3"22(-# ! 3 -5655��31� �����)� ��718.������)"
#
�������������������� ���������!��� "#���$��%��&����'