Page 1 of 7

The Original Riley

Magbase & superbase INSTALLATION INSTRUCTIONS

Baseball\Softball Bases (Little League Approved) Complete Packages Item Number

MAG1: Single Base with post (ground insert) 1 magnetic fixture and 3 shear plates. Cleaning tool sold separately. MAG1

MAG2: Single Base with post (ground insert) 1 magnetic fixture and 3 shear plates and 1 ground anchor with 1 plug. Cleaning tool sold separately. MAG2

MAG3: One double base with two posts, one magnetic fixture with three shear plates. Cleaning tool sold separately. MAG3

MAG4: Double Base with 1 Magnetic Fixture, two square posts, 1 Pkg. shear plates, double in-ground fixture and 2 plugs. Cleaning tool sold separately. MAG4

SYSTEM A: Complete Single Bag System (3 single bases and magnetic fixtures) SYSA

SYSTEM B: Complete Double Bag System (1 double base and 2 single bases with magnetic fixtures) SYSB

SYSTEM C: 3 Single Bases and posts (no magnetic fixtures) SYSC

SYSTEM D: 1 Double and 2 Single Bases and posts (no magnetic fixtures) SYSD

SYSTEM J 3 single in-ground fixtures, plugs and cleaning tool (goes with a SYSA or SYSC) SYSJ

SYSTEM K 1 double in-ground fixture and 2 single in-ground fixtures with plugs and cleaning tool (goes with a SYSB or SYSD) SYSK

Individual Baseball/Softball Bases & Replacement Parts

**Note – Instructions for all our baseball systems and packages are found in this manual. ***

Page 2 of 7

WARNING: Be advised that sliding into a

baseball/softball base represents a clear and present

danger. Injury may occur. All Players should be

informed of the risks inherent in this sport activity

IT IS VERY IMPORTANT THAT YOU

FOLLOW THESE INSTRUCTIONS

FROM HOME PLATE:

Mark out baselines for first and third base, (Use a heavy cord and wood stakes to indicate baselines. Measure the required distance from home plate to the first base position and third base position. Mark with a wood stake. Finally mark out the second base position using the first and third base markers and the correct measurement from home plate.

The in-ground fixtures must be installed 2” (minimum) below grade. The centre of the square hole must be 7 ½” from the base line for the first & third base and directly centre for second base. The double in-ground is to be installed so that the centre of one square hole is 7 ½” outside the base line and the other square hole 7 ½” inside the baseline. NOTE: The double socket can also be used to accept a single base.

Dig holes approximately 15” deep. Level bottoms of hole by adding 5” of sand or gravel. Lay fixture into hole and square with the baselines and at the correct position. Use a small level to adjust fixture so that it is level, plumb and parallel with the base lines. This is very important or the bases will not sit square with the field alignment.

INGROUND FIXTURE MUST BE INSTALLED AT LEAST 2” BELOW GRADE

Fill holes with heavy, solid earth. Install Plugs before covering fixture. Let Installation settle for 48 hours and then top off the area and level. It is very important to keep the base areas level at all times. The magnetic fixture must always sit flat on the ground. The plugs should be installed below the surface to allow dragging and levelling operations. This will also discourage vandals from finding and removing the plugs.

When using the magnetic base system (MAGBASE), the in-ground fixtures do not have to be installed with a cement mixture, and can simply use dirt or gravel filler. However if you use our in-ground fixture without the magnetic safety release feature, and use only the socket post system (SUPERBASE w/ POST), it may be necessary to cement the fixtures into the ground.

SINGLE IN-GROUND FIXTURE (SNGFX) DOUBLE IN-GROUND FIXTURE (DBLFX)

Page 3 of 7

The Fixtures must be checked before each season to make sure they are level, plumb and parallel to the base lines.

A special cleaning tool is supplied with each in-ground fixture purchase. This will enable the operator to keep the sockets free from stone, dust, gravel or earth. The plugs (Supplied) must always be inserted after the base and magnetic fixture is removed.

ASSEMBLY OF THE MEGG-NET SUPER BASE AND MAGNETIC FIXTURE

SUPER BASE - 1st BASE POSITION:

SELECT:

2-1/4" x 5/8" Socket Head Cap Screws

2-washers 1-Allen wrench

1-4" square top post with six holes

1-Super Base

1. Align the socket post over the exposed outside coupling nuts located on the bottom of the Super Base.

2. Insert the two-1/4" x 5/8" Socket Head Gap Screws with washers and tighten with Allen wrench (supplied).

SUPERBASE DOUBLE SAFE -1st BASE POSITION:

SELECT:

4-1/4" x 5/8" Socket Head Cap Screws

4-washers

1-Allen wrench

1-4" (square top) socket post with 1-1/2" square stem

1-4" (square top) socket post with 1-3/8" round stem

1-Super-D Double - Base

1. Align the 4" (square top) socket post (with 1-1/2" square stem) over the exposed insert nuts on the bottom of the white base and the 4" (square top) socket post (with the 1-3/8" round stem) over the exposed insert nuts on the bottom of the orange base.

2. Twist the socket posts so that the elongated holes allow for centre to centre adjustment of 14-1/4" centres.

3. Insert the four 1/4" x 5/8" Socket Head Cap Screws with washers and tighten with Allen Wrench (supplied).

Page 4 of 7

WARNING: Be advised that sliding into a baseball/softball

base represents a clear and present danger. Injury may occur.

All Players should be informed of the risks inherent in this

sport activity

2ND AND 3RD BASE ASSEMBLY:

SELECT FOR EACH BASE:

2-1/4" x 1/2" Flat Head Cap Screws

4-Galvanized o *See installation Steel Shear Plates of shear plates below

1-Allen wrench.

1-Super Base

ASSEMBLY OF MAGNETIC FIXTURE

SELECT FOR EACH MAGNETIC FIXTURE:

4-1/4" x 7/8" Socket Head Cap Screws

4-1/4" Nuts

1-Allen wrench

1-Magnetic fixture (See Picture)

1-4" square top post with six holes

1. Align socket post over the four holes located on the bottom of the Magnetic Fixture. 2. Insert four ¼” x 7/8” Socket Head Cap Screws from the top through the fixture and the socket

post. 3. Make sure the head of the socket screw is positioned below the magnetic surface. 4. Install 4 hex nuts and tighten with Allen wrench. Repeat this procedure for other magnetic

fixtures.

INSTALLATION OF SHEAR PLATES

The purpose of the magnetic fixture is to allow the base to absorb the impact of a sliding player by moving. This is accomplished when the base is hit with a lateral force. The shear force is controlled by the size of the galvanized steel plate that is fixed to the bottom of the base.

PLEASE LOCATE 3 DIFFERENT SIZES

OF GALVANIZED STEEL PLATES:

6” x 4” Rectangular Plate 200 Lbs. of Applied Force

4” x 4” Square Plate 120 Lbs. of Applied Force

4” x 2” Rectangular Plate 90 Lbs. of Applied Force

Page 5 of 7

IMPORTANT (READ CAREFULLY)

BEFORE ATTACHING THE SHEAR PLATE TO THE BOTTOM OF THE SUPER BASE (WITH CONCAVE BOTTOM) MAKE THE FOLLOWING SELECTION:

The 6" x 4" Rectangular Shear Force Plate should be used for all adult ladies' or men's recreational leagues.

The 4" Square Shear Force Plate should be used for children over 100 lbs. body weight (average weight).

The 4" x 2" Rectangular Shear Force Plate should only be used for children under 100 Ibs. Average body weight.

INSTRUCTIONS

Select:

2-1/4" x 1/2" Flat Head Cap Screws

1-Allen wrench A

Align selected galvanized shear plate over bottom of Super Base exposed coupling nuts. Make sure countersunk holes are facing outward so that the flat head socket screw will seat below the flat surface. It is very important that the head of the Cap Screw is not interfering with the contact between the shear plate and the magnetic fixture. Tighten with Allen wrench. Lower magnetic fixture into concave bottom of Super Base until magnetic contact is made. Make sure the fixture is square with the Super Base. Finally, Remove the in-ground fixture plug and insert Super Base and Magnetic Fixture into position. The Magnetic Release feature is only used at Second and Third positions.

TO REMOVE THE SUPER BASE FROM THE MAGNETIC FIXTURE:

1. Do not leave Magnetic Fixture fixed to the base when not in use. This is extremely important. Failure to follow this procedure will void warranty.

2. Do not pull the Base and Fixture directly apart. The Base must be sheared off the fixture. Pulling directly away from the strong magnetic surface could damage the internal structure of the Super Base and void the warranty.

3. Install a 2" (Ld.) x 12" length of pipe onto a fence post or bleacher upright. Drop the Super Base and Magnetic Fixture into the 2" pipe and grasp the base and slide the base off the fixture.

4. When the Super Base moves under the impact of a sliding player, the Magnetic Fixture must be lifted out of the socket and brushed (either by hand or with a whisk) to remove loose sand or gravel before placing the Magnetic Fixture back into position. If this is not properly administered, the magnetic contact can be disrupted.

Page 6 of 7

NOTE: The Edge of

the expanded metal

screen is very sharp.

Be careful handling

this screen around

yourself and other

people.

ASSEMBLY OF SINGLE IN-GROUND FIXTURE

Step 1: Align two plates, as illustrated, and fasten together using 3 screws. (Supplied). Make sure all steel bumps are facing away from the opening of the socket post.

Step 2: Fasten one more plate (As Illustrated) using 3 more screws (Supplied)

DO NOT TIGHTEN SCREWS UNTIL ALL FOUR PLATES ARE IN PLACE. MAKE SURE ALL THE STEEL BUMPS ARE FACING AWAY FROM THE SOCKET POST OPENING

Step 3: Fasten the fourth and final plate. This time you will need to use 6 screws to complete the assembly. Tighten all 12 screws in place, making sure the sections all come together to form a square opening in the centre.

Step 4: Turn upside down and position expanded metal screen over the 4 plates. Using the washers and screws (Supplied) fasten the screen to the 4 plates. Fasten as many as you can…if some holes do not line up it is not necessary to complete them all.

Page 7 of 7

NOTE: The Edge of the expanded metal screen is

very sharp. Be careful handling this screen around

yourself and other people.

ASSEMBLY OF DOUBLE IN-GROUND FIXTURE

Please Note: The Double In-Ground Fixture has six 7 ½” x 8 plates. (2 sets of 3). One Set marked with an ‘X’. Keep these marked plates together on one side of the fixture. Step 1: Select the 8” x 16” steel plate, one marked ‘X’ plate & one unmarked plate. Assemble as pictured. Make sure all steel bumps are facing away from the socket post opening. Fasten using three screws (Supplied) on each plate. Do not fully tighten yet. Step 2: Select one more marked ‘X’ plate and one more unmarked plate. Fasten as pictured. Fasten using three screws (Supplied) on each plate. Do not fully tighten yet. Step 3: Select final marked ‘X’ plate and last unmarked plate. Fasten as pictured. Fasten using three screws (Supplied) on each plate. Once all in place, tighten all screws making sure plates come square with each other.\ Step 4: Turn fixture upside down and position the 12” x 24” expanded metal screen over the bottom of plates. Using washers with screws, fasten screen to bottom of the fixture as illustrated in picture. Do not worry If some holes don’t line up with screen. It is not necessary to complete all of them.