the rockwell building pittsburgh, p t: . dated rockwell delta...
TRANSCRIPT
ROckWell PM-424-03-651-0003
MANUFACTURING COMPANY The Rockwell Building Pittsburgh, P t: . DATED IM-7-15-69
ROCKWELL DELTA \
14" and 16''' RA.DIAL SAWS
lf\1 rRODUCTION
Your new Rockwell / Delta Radial Saw provides all the stamina and rugged construction features necessary for heavy duty precision cutting.
14" Radial Saw
The 14" Radial Saw will cut through stock up to 4·5/ 16" thick, cross cut 1" stock to 19 .. wide and rip to the cen· ter of a 60" panel.
16" Radial Saw
The 16" Radial Saw will cut through stock up to 5·3 / 8" thick, cross cut 1" stock to 24" wide and rip to the center of a 72" panel.
SELECTING FLOOR SPACE Before unpacking, determine exactly where you want to set up the machine. It is highly desirable to locate the machine against the wall where it wi II be out of the way and wi II actually faci I i· tate materials handling through the shop.
UNPACKING ANi) SETTING UP Remove the packing material and tilt the machine to the rear. Brace the frame so the machine is balanced. Attach steel legs to each end of the base and return machfne to the upright position. Wipe the protective coating thoroughly from the working parts of the machine as well as other i terns which come with the saw. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose).
It is advisable at this time to level the machine by placing shims between the bottom of the leg and the floor.
INSTALLING CUTTINGHEAD TO TRACK-ARM 1. Remove end pi ate from track-arm.
2. Hold cuttinghead assembly with both hands, as shown in Fig. 2, and insert the first two ball bearings on the track rods. Be sure that rip lock (A) and (B) Fig. 2, iollow properly.
3. After the rip lock is on the track rods, the other two ball bearings easily follow.
4. Rep I ace end pi ate on track-arm and tighten screws.
ELECTRICAL INFORMATION
Fig. 2.
Before connecting saw to power source, the following should be checked:
1. Refer to motor nameplate to be sure motor is suppl ied for use on the power system available and that dual voltage motor connections are correct.
4. Be sure wire size is also correct, as shown in Fig. 3, between branch circuit connection, panel saw outlets and the starters supplied on the saw and that the saw is properly grounded.
2. Be sure that the wire size between the main power panel and the saw outlet is at least as large as noted in Fig. 3. For wire runs longer than 100 feet , consult your electrician for correct wire size.
3. Be sure that the power circuit the saw will be used on is properly fused as noted in Fig. 3.
5. After the saw is connected to a power source, the motor spindle (saw arbor) must turn in a clockwise direction when viewed from the saw arbor end. Check rotation before mounting saw blade. Single phase motors are set at the factory for correct rotation. If rotation of a single phase motor is incorrect, the motor should be checked by an authorized motor service station.
6. To change rotation of a saw supplied with three phase power, any two of the three power wires that run to the saw should be interchanged.
WIRE AND FUSE Sl ZE
SINGLE PHASE THREE PHASE
230 VOLTS 230 VOLTS 460 VOL TS
HP WIRE SIZE TIME LAG WIRE SIZE TIME LAG WIRE SIZE TIME LAG FUSE * F." USE * FUSE *
3 10 25 14 15 14 10
5 --- --- 12 25 14 15
*Si ze fuse selected for branch circuit protection.
Fig. 3.
2
ADJUSTING TABLE TOP PARALLEL TO TRACK-ARM For accurate work, the track-arm must be parallel to table top at all points. Adjust as follows:
1. Insert steel rod (B) Fig. 4, or similar device between motor arbor co II ars.
2. Lower steel rod unti I it just touches the wood table top.
3. Move rod to all positions on table by swiveling the trackarm and moving cuttinghead. Locate the high point on table -mark it-- then adjust all corners of table to this high point. AI• ways follow this procedure.
4. To lower the table, loosen jam nut (C) and tighten jam nut (D) Fig. 4. To raise t,he table level, reverse this adjustment. Do not turn square head screw.
5. If necessary, screws (E) Fig. 4, may be loosened and shims placed between table (A) and cast iron base.
INSTALLING SAW BLADE
Fig 4 .
1. Place one collar on arbor against the shoulder of the shaft.
Fig. 5.
KICK-BACK ADJUSTABLE TO ALL
MATERIAL THICKNESSE
The recessed side of the collar must face away from the shoulder.
2. Install saw blade on the arbor with the teeth pointing down-ward when viewed from the front of the saw.
3. Place the second collar on the arbor with recessed side against saw blade.
4. Assemble and tighten the arbor nut which has a left hand thread.
5. Mount safety guard before operating.
ADJUSTING THE SAFETY GUARD On all ripping or plowing operations, the back part of the safety guard is lowered so that it just clears the material. This will prevent the material from being I i fted off the tab I e. Also, lower the kickback device (A), 1 /8" below surface of material to eliminate "kickback", as shown in Fig. 5. Adjust dust elbow (B) to direct sawdust to rear of machine.
TAKING SIDE MOTION OUT OF OYER-ARM If side motion develops in over-arm, it can be corrected as fol·· lows:
1. Loosen hex nut (A) and gib adjusting screws (B) and (E) Fig. 6.
2. Loosen nuts (D) and adjust bolts (C) Fig. 6, so that base wraps around column securely. If column is tight in column base, bolts (C) Fig. 6, are to be turned clockwise to loosen. IMPORTANT: Turning bolts (C) clockwise will spread the base, while turning bolts (C) counterclockwise and tightening nuts (D) will tighten the base. Check elevation by turning elevating crank handle, making sure the column moves up and down without binding.
3. Tighten screws (B) Fig. 6, against the column gib until all side motion disappears in over-arm.
4. Securely lock hex nuts (A) while holding screws (B) Fig. 6.
3
Fig. 6.
HOW TO TIGHTEN YOKE AGAINST BEARING CARRIAGE After long service, "p.lay" may develop between yoke (C) and bearing carriage (B) Fig. 7. To reduce "play", proceed as follows:
1. Remove guard and saw blade.
2. Remove end plate from track-arm.
3. Remove yoke assembly from track-arm.
4~ Pull yoke clamp handle (A) Fig. 7, to loosen, and unscrew dog point screw (D) with wrench supplied.
5. Turn slotted bolt (E) Fig. 7, with heavy screwdriver (F) CLOCKWISE until dog point set screw (D) can be fitted into next slot in bolt (E) and tighten screw (D).
6. Retighten yoke clamp handle (A) Fig. 7, and reassemble.
Fig. 8.
ADJUSTMENT OF TRACK RODS
Fig. 7.
ADJUSTING BALL BEARINGS AGAINST TRACK RODS The carriage is mounted on four double grease·l')hielded ball bearings, two on fixed shafts (on saw blade side of track-arm) and the other two on adjustable, eccentric shafts •. To adjust ball bearings against track rods, proceed as follows:
1. Remove eAd plate from track-arm, loosen rip lock (C) and move carriage to the front, as shown in Fig. 8.
2. Using wrench supplied, loosen set screws that lock both front and rear bearing eccentric shafts (F). One screw is shown at (D) Fig. 8, the other at the rear of the carriage.
3. Rotate yoke unti I hoi e in yoke is under either eccentric shaft (F) Fig. 8.
4. Place special wrench (E) over hex jam nut that locks shaft (F), as shown in Fig. 8, and loosen. Repeat this procedure at rear bearing.
5. Insert hex wrench (G) into eccentric shaft (F) as shown in Fig. 8, and turn until all "play" is removed. Do same for rear bearing.
6. Tighten hex jam nuts with wrench (E) and lock set screws (D) Fig. 8, at both bearings. Replace end plate on track-arm.
Each track rod can be adjusted individually to present a new bearing surface. Adjust one at a time as follows:
1. Remove track-arm end plate.
2. Remove entire cuttinghead assembly from the track-arm.
3. Loosen screws (B) Fig. 9, slightly, just enough to release hold action on track rod (A).
4. Insert screwdriver into slotted end of track rod (A) Fig. 9, and turn slightly right or left. Retighten screws (B).
5. Repeat adjustment on each track rod. When complete, in· sert cuttinghead and replace track-arm end plate.
4
TRACKS "CAN BE EASILY ROTATEO TO COMPENSATE FOR WEAR
Fig. 9.
ADJUSTING BLADE SQUARE WITH TABLE TOP 1. Remove saw guard and place saw blade (A) in cut-off po-sition over fixed portion of table, as shown in Fig. 10.
2. Place a steel square (B) Fig. 10, against saw blade. Be sure souare is between the gullets and not against saw teeth.
3. Pull out bevel clamp handle (C) Fig. 10, and loosen bolts (D).
4. Tilt motor assembly until square is flush against saw blade and tighten bevel clamp handle (C) Fig. 10, to hold position. Then lock both bolts (D).
5. If the above adjustment is not sufficient, remove scale plate (E) Fig. 10, and loosen the two socket head screws located above, and below the center pivot screw. Rotate motor for approximate adjustment and retighten the two socket head screws.
6. Replace scale plate (E) Fig. 10, and repeat operations I is ted for final adjustment.
Fig. 10
ADJUSTING BEVEL CLAMP HANDLE When the bevel clamp handle (B) Fig. 11, does not securely lock the motor, adjustment can be made as follows:
1. Loosen bevel clamp handle (B) as shown in Fig. 11.
2. Turn bolt (D) clockwise to tighten and securely lock by tightening hex nut (C) Fig. 11.
Fig. II.
ADJUSTING OVER-ARM CLAMP HANDLE When clamp handle (A) Fig. 12, has to be moved beyond vertical position for clamping over-arm, adjustment can be made as follows:
1. Move clamp handle (A) Fig. 12, as far as it will go for clamping.
2. Remove nut (B) Fig. 12.
3. Remove clamp handle and replace it in a vertical position on stud.
4. Replace and tighten nut (B) Fig. 12.
5
Fig. 12.
ADJUSTING SAW TRAVEL SQUARE WITH FENCE Your Radial Saw is equipped with exclusive "Micro-Set" Miter Stops. This unique feature makes it possible to produce accurate miter cuts and perfectly square cross cuts at all times by individual adjustment · of the three stop positions. These stops are accurately' adjusted at the factory, however, future adjustments can be made if necessary.
Once the "Micro-Set" stops are set, you can be assured of quick, pos·itive settings at the three positions.
Before determining if thG "Micro-Set" stops require adjustment, check saw travel for squareness with table fence. To do accurate work, saw travel must be 90 degrees to the fence. Check and adjust as follows:
1. Place a steel square (B) against fence, as shown in Fig. 13, and lower cuttinghead so that saw blade (A) just clears table top.
2. Pull cuttinghead along square (B) Fig. 13. If saw blade does not travel parallel to the square, the following adjustment is necessary.
Fig. 13.
3. Remove cover plate (A) Fig. 14.
Fig. 4.
4. Locate center cap screw (B) Fig. 14, inside pivot column and loosen slightly •. Tap center cap screw (B) sharply with a block of wood or insert a thin wooden wedge inside the column to loosen the tapered plug (C) Fig. 14, that is attached to the cali screw (B). It is very important that the tapered plug (C) is loosened before any further adjustment is made.
5. Loosen clamp handle (D) Fig. 13.
6. Using small wrench on hex nut (F) Fig. 13, turn slightly to one side. CAUTION: Do not attempt to rotate completely. Notice that the entire track also moves.
7. When saw blade tracks evenly against steel square, tighten clamp handle (D) Fig. 13, and center cap screw (B) Fig. 14.
8. Check pointer and adjust to 0 degrees if necessary.
9. Replace cover plate (A) Fig. 14.
10. Right and left miter positions can be independently adjusted using the same procedure as above. If protractor square is not available, trial cuts can be made to determine if adjustment is necessary.
6
REMOVING "HEELING" IN SAW CUT Even though the cuttinghead travel may be perfectly aligned at 90 degrees to the fence, the blade itself may not be 90 degrees or square with the fence, as shown in Fig. 15. This condition is known as "heeling".
To check and adjust, proceed as follows:
1. Cross cut a board and see on which side of the cut board saw teeth marks appear.
2. If saw teeth marks appear on the right side, the back end of the saw blade must be shifted toward left side.
3. Loosen yoke clamp handle~ Then loosen both screws (H) Fig. 13 and turn yoke (J) COUNTERCLOCKWISE. If saw teeth marks appear on left side of board, turn yoke (J) CLOCKWISE.
4. Tighten yoke clamp handle to hold position and retighten screws (H) Fig. 13.
5. Make another test and continue this adjustment unti I "heel-ing" is corrected.
SAFETY SUGGESTIONS
FENCE
Fig. ts.
1. Always turn off power and wait unti I saw blade stops turn-ing before adjusting, changing set-ups or leaving saw.
2. Follow red warning on saw guard for instructions on ripping.
3. Keep saw blade clean, sharp and properly filed.
4. Adjust end of guard opposite dust spout down to material for all ripping operations.
5. Always use anti-kickback fingers when ripping.
6. Be sure that all clamp handles are properly tightened before operating machine.
7. Be sure material rests firmly against the guide fence in cut-off position before starting to cut.
8. Be sure end plates are securely fastened to track-ann be-fore using saw.
9. Keep blade and arbor flanges free from dirt and grease.
10. Guards should be in place and used at all times.
7
...Jw wo >z <tw a:IL. .... IL.o o.,... w zc, ...J(1)
~34(4) 1 ~ ~35(4) ~36
8
/ /
**45 ~47(3)
/
~/_/**48(4) /~
. ·""-, ~ ~ ~~50(41
**52(28) 51 (2 )
**53 (28)
Ref,
No.
1
2 3 4 5 6 7 8
~ 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 29 30 31 32 33 34 35 36 37 38 39 40 42 43 44 45 47 48 50 51 52 53 54 55 56 57 58 59 60 61 62
·Part
No.
SP-558 MK-5916 MJ-4879 SP-605 904-10-091-2444 MJ-4880 MJ-4874 SP-2250 SP-509 438-01-009-0036 424-03-089-0009 NJ-247 MK-5317 MJ-4865 SP-1606 SP-1207 MJ-4864 MK-5315 MH-3417 SP-558 MJ-4882-S
MH-3493 SP-8210 SP-1300 MK-5448 SP-6731
SP-767 MJ-4875 SP-7105 SP-406 MJ-4231 SP-1705 SP-3120 MJ-4226 MJ-4227 SP-1703 SP-649 424.-03-055-0004 SP-1705 SP-3308 SP-7105 951-02-011-4344 SP-558 424-03-108-0005 SP-791 MJ-4411 902-03-020-2982 SP-541 MJ-4549 MK-5599 MK-5598 MK-5840 MJ-4545 SP-558 MH-3065 MJ-4215 SP-558
Replacement Parts Description
#8-32 x 1/4" Rd. Hd. Scr. Cover Index Colwnn 5/16-18 x 1/2" Hex. Hd. Scr. Special Washer Plug Miter Scale #4 x 3/16" Drive Screw 1/4-20 x 1/2" Rd. Hd Scr Cord Clamp Arm Knob Lock Rod Bracket 7/16 X 1 X 5/64" Washer 3/8"-24 Hex. Nut Stud Conduit Pointer #8-32 x 1/4" Rd. Hd Scr Index Housing, including: Spring #OO x 1/8" Drive Screw 5/16"-18 Hex Nut Knob 5/64 x l/2" Roll Pin 1/4-20 x 1" Soc. Hd. Scr. Spacer 1/4 x 1-1/4" Groove Pin 1/4-20 x 3/4" Flat Hd. Scr. Colwnn Key 1/2" Split Lockwasher 1/2-13 x 1-3/4" Hex. Hd. Scr. Colwnn Elevating Nut 5/16" Split Lockwasher 5/16-18 x 1" Hex. Hd. Scr. Track 1/2" Split Lockwasher 1/2-13 X 1-3/4" Soc. Hd. Scr. 1/4 x 1-1/4" Groove Pin Rip Scale #8-32 x 1/4" Rd. Hd. Scr. Ball Race Rod 3/8-16 x 3/4" Soc. Hd. Scr. Track End Cover Speed Nut #10-24 X 3/4" Rd. Hd. Scr. Yoke Pin Eccentric Bearing Stud Stationary Bearing Stud Bearing Roller Head #8-32 x 1/4" Rd. Hd. Scr. Pointer Rip Lock Hold Down Plate #8-32 x 1/4" Rd. Hd. Scr.
Ref. Part
No. No.
63 MK -5452-S 64 MH-3423-S 65 SP-232 66 SP-202 67 MJ-4232 68 SP-1705 69 SP-1227 70 MJ-4306-S 71 MH-3493 72 MK-5448 73 SP-784 74 MK-5592-S 75 SP-1528 .76 MK-5597 77 SP-2250 78 960-02-012-1401 79 SP-2252 80 MH-3805 81 MK-5319-S 82 424-04-071-0013 83 MK-5904 84 SP-2489 85 904-15-062-0269 99 MJ-4557 100 SP-558 101 SP-3319 102 MJ-4555 103 SP-1103 104 NJ-247 105 MK-5317 106 MK-5311 107 MJ-4546 108 SP-1026 109 DDL-175 110 MK-5907 111 SP-644 112 MK-5909 113 MK-5448 114 MJ-4550 115 SP-3000
116 MH-3417 117 SP-558 118 MJ-4306-S 119 MH-3493 120 MK-5448 121 SP-784 122 SP-228 123 SP-784 124 MJ-4547 125 SP-202 126 MG-170 127 SP-1404 128 SP-1606 129 424-04-054-0015 130 MJ-4821
. 131 MK -5523 132 Ca~ #33-183 133 MK-5520
9
Description
Rip Lock, including: Knob, including: 1/4-20 x 3/8" Soc. Set Scr. 1/4-20 x 1/2" Soc. Set Scr. Rubber Bumper 1/2" Split Lockwasher 1(2"-20 Hex. Jam Nut Locating Housing, including: Spring Knob 3/8-16 X 1-1/4" Soc. Hd. Scr. Guard Assembly, including: 5/16-18 x 1" Thwnb Screw Dust Spout #4 x 3/16" Drive Screw Nameplate #2 x 3/16" Drive Screw Caution Plate Anti -Kickback Rod, including: Pin Finger 1/8 x 7/8" Groove Pin Retaining Ring Cover
. .,
#8-32 x 1/4" Rd. Hd. Scr. 1/2-13 x 3/4" Soc. Hd. Scr. Rear Trmmion Boss 5/16-18 x 5/8" Soc. Set scr. Knob Lock Rod LockNut Yoke 3/8"-16 Hex. Nut Special Washer Bevel Lock Nut 3/8-16 x 2-1/2" Hex. Hd. Scr. Bevel Lock Rod Knob Bevel Scale #6-32 x 1/4" Rd. Hd. SelfTapping Screw Pointer #8-32 x 1/4" Rd. Hd. Scr. Locating Housing, including: Spring Knob 3/8-16 x 1-1/4" Soc. Hd. Scr. 1/2-13 x 1-1/4" Soc. Hd. Scr. 3/8-16 x 1-1/4" Soc. Hd. Scr. Front Trunnion 1/4-20 x 1/2" Soc. Set Scr. Plug 3/8"-16 Wing Nut 7/16 x 1 x 5/64" Washer Guard Clamp Stud Arbcr Collar 16" Combination Blade Arbor Nut
196
145 (2)
I i i
"','::\f
212 (4)
211 02) f 210(12J
~146(4) ' ~147(4)
v~l49(4) -----150
._151(6)
$--152(6) . ififl75 (4)
**i73 (4) 'l*if 176 (2)
---**174(4) // ififl77(2)
1'·~. 0/:::;::~; ' ~ .
-~-
~- -~ ~- ' l ~--....j
. -~ ififl60 (2)
.......... ------162 .......... ~161(2)
195 (2)
·~194 ~~--
193
~192(2)
,.,?\ 190
A DUE TO VARIANCE IN WOOD THICKNESSES, WE SUGGEST THAT ALL FIVE TABLE BOARDS BE REPLACED.
I I THESE PARTS ARE FOR THE 16" SAW ONLY
10
Replacement Parts Ref. Part Description Ref. Part Description No. No. No. No.
135 SP-514 1/4-20 x 3/8" Rd. Hd. Scr. 181 MH-3423-S Knob, including: 136 MK-5243 Gib 182 SP-232 1/4-20 x 3/8" Soc. Set Scr. 137 MJ-4228 Column Base 190 MJ-4905-S Crank 138 SP-1026 3/8"-16 Hex. Nut 191 SP-5045 3/16" x 1-1/2" Groove Pin 139 SP-1704 3/8" Split Lockwasher 192 SP-417 3/8-16 x 1" Flat Head Screw 140 MK-5241 Spreader Stud 193 MK-5231 Elevating Shaft Bearing 141 901-04-081-3630 5/16-18 x 1-1/2" Headless 194 MJ-4910 Elevating Shaft
Set scr. 195 SP-1026 3/8"-16 Hex. Nut 142 SP-5435 5/16"-18 Hex. Jam Nut 196 MH-3919 Thrust Bearing 143 SP-509 1/4-20 x 1/2" Rd. Hd. Scr. 197 MH-3921 Bearing 144 438-01-009-0038 Cord Clamp 198 MH-3923-R Gear 145 SP-7105 1/4 x 1-1/4" Groove Pin 199 SP-5030 3/16 x 3/4 Groove Pin 146 SP-3109 1/2-13 x 2-1/2" Hex. Hd. Scr. 200 SP-648 3/8-16 x 1-1/4" Hex. Hd. Scr. 147 SP-1705 1/2" Split Lockwasher 201 SP-1704 3/8" Split Lockwasher 148 SP-646 3/8-16 x 2" Hex. Hd. Scr. 202 MJ-4229 Column Housing 149 SP-617 3/8-16 x 1-1/2" Hex. Hd. Scr. 203 MJ-4911 Elevating Screw 150 MJ-4230 Table Base 204 CBL-426 Special Washer 151 SP-1704 3/8" Split Lockwasher 205 MH-3920 Bearing 152 SP-1026 3/8"-16 Hex. Nut 206 SP-2607 #3 Woodruff Key 153 MJ-4027 Fence 208 SP-1011 1/2"-13 He1;. Nut
424-03-311-0004 Board Assembly, consisting of: 209 SP-2106 1/8 x 1-1/4" Cotter Pin 154 MJ-4030 7" Table Board 210 SP-1307 3/8"-16 Sq. Nut 155 MJ-4026 3" Table Board 211 SP-1704 3/8" Split Lockwasher 156 M.l-40'25 3-1/'2" 1 able Board '2.1'2. MK-50'14 Leg 15'1 424-03-011-0()11 11" 'fable Board '213 SP-'23'15 3/8-16 x 1" Sq_. Hd. Bolt 158 424-03-011-0012 6" Table Board 214 SP-1026 3/8"-16 Hex. Nut 159 SP-1614 9/32 x 5/8 x 1/16" washer 215 SP-1005 3/8"-16 Hex. Jam Nut 160 SP-511 1/4-20 x 7/8" Rd. Hd. Scr. 216 SP-324 3/8-16 X 2" Sq. Hd. Set Scr. 161 424-03-304-0009 Bar 217 960-01-012-0019 Nameplate 162 424-03-304-0010 Bar 218 SP-2250 #4 x 3/16" Drive Screw 171 424-03-305-0009 Frame Assembly 220 Cat. #1534 1/8" Hex. Wrench 172 MK-5322 Reinforcing Strip 221 MJ-4409 5/32" Hex. Wrench 173 SP-640 3/8-16 x 3/4" Hex. Hd. Scr. 222 Gat. #1532 1/4" Hex. Wrench 174 SP-1704 3/8" Split Lockwasher 223 Cat. #1536 5/16" Hex. Wrench 175 SBS-55 Special Washer 224 MK-5918 Roller Head Wrench 176 424-03-014-0017 Fence Clamp Bracket 225 MH-3100 Wrench 177 424-03-327-0003 Fence Clamping Nut 225 TAS-78 Wrench 178 SP-2101 3/32 x 5/8" Cotter Pin 226 MS-61 Wrench 179 424-03-112-0003 Fence Clamp Screw 180 961-03-010-2865 Grommet
11
Ref. - Part No. No. 12 MJ-4863 41 MJ-4861 46 MJ-4420 49 MJ-4415 52 902-03-020-2982 53 SP-541 86 424-03-354-0010 87 SP-1505 88 SP-1527 89 960-04-012-0031 90 SP-2250 91 960-02-012-0028 92 SP-2252 93 MJ-4808
MK-5906-S
94 MK-5906-A 95 SP-2849 96 904-15-062-0269 9'7 MK-5904 98 424-04-071-0013
NOTE: THESE PARTS ARE FOR THE 14" SAW ONLY
92121
9 1
12~~1 1, 4 l-~i
·<~?t,~, ; / "'i-..: // .. ~ / \.
:~ )-::: ~52 120) '
~ -~ ~ 53120)~ /~ 49141 ~
153
ADUE TO VARIANCE IN WOOD THICKNESSES, WE SUGGEST THAT ALL FOUR TABLE 'BOARDS BE REPLACED.
Replacement Parts Description Ref. Part Description
No. No. Arm 134 Cat. #33-179 14" Combination Blade Track 153 MJ-4027 Fence Rip Scale MJ-4024-T Board Assembly, consisting of: Ball Race Rod 164 MJ-4030 7" Tab1e Board Speed Nut 165 MJ-4026 ' 3" Tab1e Board ·' #10-24 X 3/4" Rd. Hd. Scr. 166 MJ-4025 3-1/2" Tab1e Board Guard Ass'y. , including: 167 MJ-4024 11" Table Board ' 1/4-20 x 1/2" Thumb Screw 168 SP-7502 3/8-16 x 1" Rd. Hd. Scr. 5/16-18 x 3/4" Thumb Screw 169 SP-1615 13/32 x 13/16 x 1/16" Washer Caution Plate 170 MJ-4029 Tab1e Adjustment Bar #4 x 3/16" Drive Screw 171 424-03-305-0009 Frame Assembly Nameplate 181 MH-3423-S Knob, including: #2 x 3/16" Drive Screw 182 SP-232 1/4-20 X 3/8" Soc. Set Scr. Dust Spout 183 MJ-4906 Fence Clamp Bracket Complete Anti-Kickback Rod Assy., 184 SP-642 3/8-16 x 1" Hex. Hd. Scr. consisting of: 185 SP-1026 3/8 "-16 Hex. Nut Rod Assembly, including: 186 MJ-4907 Fence Clamp Screw 1/8 x 7/8 Groove Pin 187 MK-5237 Fence Clamping Nut Retaining"lli_n~ 188 03L-447 Special Washer Finger Pin 12