this to certify that swiss krono osb structural bracing panels

Sam Guindi – Product Certification Manager Bureau Veritas Australia Pty Ltd

Quintin Kleyn - Unrestricted Building Certifier Hendry Group Pty Ltd

Date of issue: 22 July 2021

Date of expiry: 20 July 2023

Certificate number: CM70077 Rev1

This certificate is only valid when reproduced in its entirety.

of 5

Certification Body:

Bureau Veritas Australia Pty Ltd 3/435 Williamstown Road

Port Melbourne VIC, 3207

Ph: 1800 855 190

www.bureauveritas.com.au

Certificate Holder:

SWISS KRONO TEX

GmbH & Co. KG Wittstocker Chaussee 1

16909 Heiligengrabe,

Deutschland

Ph: +49 33962 69 740

Web: www.swisskrono.com

Certificate number: CM70077 Rev1

THIS TO CERTIFY THAT

Swiss Krono OSB – Structural Bracing Panels

Type and/or use of product:

Structural Bracing Panels for use in floors, walls and roof structures.

Description of product: Swiss Krono OSB is a multi-layered Oriented Strand Board for use in the design and construction of load-bearing and stiffening building elements including walls, flooring, ceilings and roofing. The product is suitable for use in dry and humid conditions.

Products include: IBS EUROFloor OSB/3 SWISS KRONO OSB/3 EN300 SWISS KRONO OSB/4 EN300

COMPLIES WITH THE FOLLOWING BCA PROVISIONS AND STATE OR TERRITORY VARIATION(S) BCA 2019

Volume One Volume Two

Performance Requirement(s) BP1.1(a), limited to (b)(i)(ii)(iii) Structural reliability P2.1.1(a), limited to (b)(i)(ii)(iii) Structural stability and resistance

Deemed-to-Satisfy Provision(s): N/A N/A

State or territory variation(s): N/A N/A

SUBJECT TO THE FOLLOWING LIMITATIONS AND CONDITIONS AND THE PRODUCT TECHNICAL DATA IN APPENDIX A AND EVALUATION STATEMENTS IN APPENDIX B

Limitations and conditions:

1. Framing to which this product is attached shall be constructed in accordance with AS1684.2 or AS1684.3 as applicable.

Building classification/s: Volume 1 – Class 2 to Class 9 buildings Volume 2 – Class 1 and Class 10 buildings

Certificate number: CM70077 Rev1 This certificate is only valid when reproduced in its entirety. of 5

2. When used as wall bracing, the product shall be installed in accordance with AS1684.2-2010 for non-cyclonic and AS1684.3-2010 for cyclonic regions.

3. Flooring shall be installed in accordance with AS/NZS 1860.2-2006

4. Minimum panel thickness of 9mm for pitched roofs, 11mm for flat roofs not required to be accessed, and 15mm for flat roofs required to be accessed shall be used.

5. Selected fixings shall take into account the wind region where the building is constructed.

6. Sarking material complying with AS4200.1 and AS4200.2 shall be used where weathertightness is required.

7. This certification is limited to the use in Class 1 and 10 buildings, and buildings of Type C construction as defined in the BCA.

8. Swiss Krono OSB shall be installed in accordance with the SWISS KRONO OSB Installation Manual (October 2019) and installed only by trade qualified installers.

Scope of certification: The CodeMark Scheme is a building product certification scheme. The rules of the Scheme are available at the ABCB website www.abcb.gov.au. This Certificate of Conformity is to confirm

that the relevant requirements of the Building Code of Australia (BCA) as claimed against have been met. The responsibility for the product performance and its fitness for the intended use remain with the

certificate holder. The certification is not transferrable to a manufacturer not listed on Appendix A of this certificate.

Disclaimer: The Scheme Owner, Scheme Administrator and Scheme Accreditation Body do not make any representations, warranties or guarantees, and accept no legal liability whatsoever arising from or

connected to, the accuracy, reliability, currency or completeness of any material contained within this certificate; and the Scheme Owner, Scheme Administrator and Scheme Accreditation Body disclaim to the

extent permitted by law, all liability (including negligence) for claims of losses, expenses, damages and costs arising as a result of the use of the product(s) referred to in this certificate.


APPENDIX A – PRODUCT TECHNICAL DATA

A1 Type and intended use of product Refer to Page 1.

A2 Description of product Refer to Page 1. A3 Product specification Product composition:

Wood strands (~90%)

Reacted PMDI (CAS-No 9009-54-5) (2 – 5%)

Solid paraffin wax (0.3 - 2%)

Water (4 – 8%) The SWISS KRONO OSB is produced in standard thicknesses: 6mm, 8mm, 9mm, 11mm, 15mm, 18mm, 20mm, 22mm, 40mm The SWISS KRONO OSB/3 EN300 and OSB/4 EN300 is available in various sizes from 2500mm x 675mm up to 5000mm x 2500mm, with square or tongue-and-groove edges. IBS EUROFloor is available in 2400x1200x20mm and 3600x1200x20mm sheets with a tongue and groove edge. Further details of the product specification may be found in the following documents:

SWISS KRONO OSB – Complete OSB Portfolio, Art No. P00241 (undated)

IBS EUROFloor – IBS Product Specification Version 1 (1 June 2020) A4 Manufacturer and manufacturing plant(s) 1. Wittstocker Chausse 1, 16909 Heiligengrabe, Germany 2. Swiss Krono Kft. Vásárosnamény, Ipar u. 1, 4800 Hungary A5 Installation requirements The product is installed in accordance with:

SWISS KRONO OSB Installation Manual (October 2019)

IBS EUROFloor, Design and Installation Guide Version 2 (July 2021)


A6 Other relevant technical data 1. Swiss Krono Material Safety Data Sheet (4 pages), validation date 1 June 2019

This data sheet provides details of the composition and materials information of SWISS KRONO OSB 2. Zwick Roell – Quality Management, Test Report 20200415_1765167_0140_1 1.zs2, date printed 15 April 2020

This report provides data on the 12mm SWISS KRONO OSB/3 3. Zwick Roell – Quality Management, Test Report 20200414_1765141_0140_1 1.zs2, date printed 14 April 2020

This report provides data on the 18mm SWISS KRONO OSB/3 4. Environmental Product Declaration – Swiss Krono, Ref No: EPD-KRO-20200203-IBD1-DE, dated 15 June 2021

This document contains information about the composition, properties and other technical data about SWISS KRONO


APPENDIX B – EVALUATION STATEMENTS

B1 Evaluation methods Structural Assessment

A2.2(2)(a)/A5.2(1)(e) - A certificate or report from a professional engineer or other appropriately qualified person (HFB Engineering and UTS); and

A2.2(2)(a)/A5.2(1)(f) – Other documentary evidence (SWISS KRONO product declaration & Span tables) B2 Reports 1. Swiss Krono Declaration of Performance – SKDE_OSB-3_CPR_2019_048 (27 August 2019)

This report contains a declaration of compliance for the SWISS KRONO OSB/3 EN300 at various thicknesses in accordance with EN 300 2. Swiss Krono Declaration of Performance – SKDE_OSB-4_CPR_2020_055 (1 April 2020)

This report contains a declaration of compliance for the SWISS KRONO OSB/4 EN300 at various thicknesses in accordance with EN 300

3. Swiss Krono OSB/3 EN300 & Swiss Krono OSB/4 EN300 – Dimensioning Reference Tables (July 2021) These tables provide span information for various thicknesses of SWISS KRONO OSB/3 EN300 and SWISS KRONO OSB/4 EN300

4. EN 13986:2004+A1:2015 Certification Report by HFB Engineering GMBH – Report No. CR311001291/2/2018 (21/02/2019)

This report contains the findings of HFB and statement of compliance in accordance with the EN standard for Oriented Strand Board (OSB) 5. UTS, Structural letter, Oriented Strand Board (OSB) 18mm and 22mm Structural Flooring (29 May 2019)

This letter provides the opinion of a registered structural engineer and indicates that the testing conducting to EN standards meets the requirements to satisfy compliance with the National Construction Code of Australia.

6. UTS, Structural letter, Oriented Strand Board (OSB) Structural Panels (29 May 2019)

This letter provides the opinion of a registered structural engineer and indicates that the testing conducting to EN standards meets the requirements to satisfy compliance with the National Construction Code of Australia.

this to certify that swiss krono osb structural bracing panels

Documents