thomas steinhauser - foundry-planet.com
TRANSCRIPT
![Page 1: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/1.jpg)
Inorganic binders – benefits –state of the art – actual use
02/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 2: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/2.jpg)
History
- 1995 start of development, University of Duisburg
- 1996 first patents
~ 2000 first serial production (cylinder heads)
~ 2005 several producers with similar systems in the market
- 2017 serial production of automotive parts (BMW, VW, Mercedes Benz, etc.)
02/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 3: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/3.jpg)
Benefits
Eliminate emissions, increase productivity/quality :• core production,
• casting
• decoring / shake-out
• sand reclamation
Cost efficiency:• lower/no costs for waste disposal
• reduced costs for exhaust air treatment
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 4: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/4.jpg)
Inorganic binder system
Sodium silicate: x SiO2 • y Na2O • z H2O
Additives to optimize the process/ casting surface
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 5: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/5.jpg)
Inorganic process
Main process differences vs. existing technologies
1. Hardening by physical elimination of water
2. Tool temperature 280° – 360°F (140° – 180°C)
3. Microwave drying/ hot air gassing
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 6: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/6.jpg)
Inorganic binding processes
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
solvent: waterSodium silicate binder
DT
AWB-binder-bridges
![Page 7: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/7.jpg)
Inorganic process
Main process differences vs. existing technologies
1. Hardening by physical elimination of water
2. Tool temperature 280° – 360°F (140° – 180°C)
3. Microwave drying
4. Cores storable for several weeks when fully dried
5. Less core gas, less casting defects
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 8: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/8.jpg)
Cogas-Test
0
20
40
60
80
100
120
140
160
180
200
0 50 100 150 200 250 300
measurment duration [sec]
Gasm
en
ge [
g p
ro 1
00g
Kern
gew
ich
t]
Coldbox AWB Hotbox
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
IOB
Measurement duration [sec]
Gasm
enge
[g pr
o 100
g Ker
ngew
icht]
![Page 9: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/9.jpg)
Inorganic process
Main process differences vs. existing technologies
1. Hardening by physical elimination of water
2. Tool temperature 280° – 360°F (140° – 180°C)
3. Microwave drying
4. Cores storable for several weeks when fully dried
5. Less core gas, less casting defects
6. Good shakeout
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 10: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/10.jpg)
Bending strength subject to temperature
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
T=100 bis 200°C => free water evaporates
T=200 bis 600°C => bonded water (OH) disappears => shrinking + cracking of binder bridges
T >750°C => secondary glas melt
![Page 11: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/11.jpg)
Inorganic process
Main process differences vs. existing technologies
1. Hardening by physical elimination of water
2. Tool temperature 280° – 360°F (140° – 180°C)
3. Microwave drying
4. Cores storable for several weeks when fully dried
5. Less core gas, less casting defects
6. Good shakeout
7. reclaimable
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 12: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/12.jpg)
Reclamation
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
Vibramill
deagglomeration
dedusting
![Page 13: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/13.jpg)
Comparison bending strength reclaimed new sand
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 14: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/14.jpg)
mixing
Core shooting
Microwave drying
castingdecoring
Sand reclamation Core storage
Inorganic – Process flow chart
![Page 15: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/15.jpg)
Improvement of the surface properties
![Page 16: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/16.jpg)
Prevention of sand adhesion
• Coating
• Addition of a gas former
• Substitution of silica sand by non wettable material
• Modification of sand wettability by additives
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 17: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/17.jpg)
Wettability
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 18: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/18.jpg)
SEM-picture: Surface lotus leaf
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 19: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/19.jpg)
SEM-picture: Surface silica sand
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 20: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/20.jpg)
SEM-picture: nano particles
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 21: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/21.jpg)
SEM-picture: silica sand with nanoparticles
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 22: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/22.jpg)
Casting without / with nano particles
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
without nano-particles With nano-particles
![Page 23: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/23.jpg)
Castings
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 24: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/24.jpg)
Selection of Cores produced with AWB
01/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 25: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/25.jpg)
02/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser
![Page 26: Thomas Steinhauser - Foundry-planet.com](https://reader030.vdocuments.net/reader030/viewer/2022012710/61a9d392a3bdc33ea265873a/html5/thumbnails/26.jpg)
Thank you very much for your attention !
02/03/2017 Prof. Dr.-Ing. Thomas Steinhäuser