thread-view system model 3625 - quest...

2
Quest Metrology’s fully automated non-contact measurement systems have and continue to revolutionize external thread measurement practices for Unified Thread Standard (UNC, UNF, UNEF and UNJ) gages and product, in both accuracy and speed of process. Achieved in less than four minutes! Thread-View System ® Model 3625 Our flagship Thread-View System ® - for external threads - delivers the ability to rapidly measure and record a diverse range of UN-type thread characteristics for both thread gages and product screw threads that are simply not achievable with micrometers or optical comparators. In one two-minute cycle, this revolutionary system will automatically measure and record the full set of geometries required for compliance standard measurements. Measured geometries Major diameter (full form and truncated) o Leading and trailing angles o Included angle Minor diameter Lead Lead over several threads Pitch diameter Root radius ("J" series threads) and reporting functions. FULL-FORM NON-CONTACT MEASUREMENT IS A REALITY . Through the application of advanced laser measurement and vision technologies, Quest Metrology delivers the first true full-form non-contact thread form measurement inspection systems, enabling accurate measurement in only seconds, not minutes using just one device. ENHANCED SOFTWARE NOW AVAILABLE About Quest Metrology Operating exclusively in thread form inspection and measurement technologies, Quest Metrology is the forerunner in the development and delivery of non-contact automated thread measurement systems and services. Whether the need is parts inspection or gage calibration, we have and are developing next generation systems and solutions to process in seconds, fully accurate, full-form inspection of UN-type, NPT and API threaded components. Data is captured and measurements calculated automatically without need for expert interpretation. The system is thus user-friendly to any operator trained in the measurement technique without need of special metrology expertise. Features and Benefits of Use Perform instantaneous gage calibration, first article inspection or measurement of an inventoried threaded part. Eliminate human error and machine bias from thread measurement process. Meets all current industry thread specifications including Systems 22 and 23 both inch and metric Reduce cost of gage calibration and external screw form product measurements Improve production quality and process control User friendly – New operators can learn to use in less than 20 minutes Full form NIST traceable certification printed after measurement cycle within 1.5 minutes (Data on12 characteristics) Settle dimensional disputes immediately Eliminate threaded components field problems and failures With the Thread-View System, true quality control will now be under your control.

Upload: others

Post on 24-Jul-2020

11 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Thread-View System Model 3625 - Quest Metrologyquestmetrology.com/sites/quest.v3k.net/files/styles... · • Lead over several threads • Pitch diameter • Root radius ("J" series

Quest Metrology’s fully automated non-contact measurement systems have and continue to revolutionize external thread measurement practices for Unified Thread Standard (UNC, UNF, UNEF and UNJ) gages and product, in both accuracy and speed of process. Achieved in less than four minutes!

Thread-View System® Model 3625

Our flagship Thread-View System® - for external

threads - delivers the ability to rapidly measure

and record a diverse range of UN-type thread

characteristics for both thread gages and product

screw threads that are simply not achievable

with micrometers or optical comparators.

In one two-minute cycle, this revolutionary

system will automatically measure and record

the full set of geometries required for compliance

standard measurements.

Measured geometries

• Major diameter (full form and truncated) o Leading and trailing angleso Included angle

• Minor diameter• Lead• Lead over several threads• Pitch diameter• Root radius ("J" series threads) and reporting

functions.

FULL-FORM NON-CONTACT

MEASUREMENT IS A REALITY.

Through the application of advanced

laser measurement and vision

technologies, Quest Metrology delivers

the first true full-form non-contact

thread form measurement inspection

systems, enabling accurate

measurement in only seconds, not

minutes using just one device.

ENHANCED SOFTWARENOW AVAILABLE

About Quest Metrology

Operating exclusively in thread form

inspection and measurement

technologies, Quest Metrology is the

forerunner in the development and

delivery of non-contact automated

thread measurement systems and

services. Whether the need is parts

inspection or gage calibration, we have

and are developing next generation

systems and solutions to process in

seconds, fully accurate, full-form

inspection of UN-type, NPT and API

threaded components.

Data is captured and measurements calculated

automatically without need for expert

interpretation. The system is thus user-friendly to

any operator trained in the measurement

technique without need of special metrology

expertise.

Features and Benefits of Use

Perform instantaneous gage calibration, first article inspection or measurement of an inventoried threaded part.

Eliminate human error and machine bias from thread measurement process.

Meets all current industry thread specifications including Systems 22 and 23 both inch and metric

Reduce cost of gage calibration and external screw form product measurements

Improve production quality and process control

User friendly – New operators can learn to use in less than 20 minutes

Full form NIST traceable certification printed after measurement cycle within 1.5 minutes (Data on12 characteristics)

Settle dimensional disputes immediately

Eliminate threaded components field problems and failures

With the Thread-View System, true quality control will now be under your control.

Page 2: Thread-View System Model 3625 - Quest Metrologyquestmetrology.com/sites/quest.v3k.net/files/styles... · • Lead over several threads • Pitch diameter • Root radius ("J" series

PERFORMANCE SPECIFICATIONSPERFORMANCE SPECIFICATIONS

Measurable form: UNC, UNF, UNEF, UNJ - English or Metric

Size: 0.0600 inches through 4.5 inches diameter or metric equivalent

Articles: External threaded product or gage (go/no-go work plugs and set plugs)

StandardsASME b1.1, b1.2, b1.3, inch and b1.16M. Federal Standard H28 section 20, Mil-S-8879C (System 22 and 23)SAE AS8879C (Category 1 and 2)

Pitch range 10 TPI or Greater

Repeatability: ± 15.2 micro inches (99%)

Single Process Cycle: Less than 2 minutes

Max Load: 9.0 lbs (4.08 Kg)

SYSTEM SPECIFICATIONSSYSTEM SPECIFICATIONS

Export formats .pdf and .xls

System configuration Self-contained system; external key board, mouse and LCD display

Light source Collimated LED (Light Emitting Diode)

Power requirements AC 120V

System management Remote login / or disk upload for security environments

Calibration cycle Annual / or with any system relocation

Thread-View Systems are a cost saving tool that will change the way you do business.

Mechanical gauges have to be read and errors

can result. Likewise multi-device measurement

processes take time and are dependent upon

expert inspection and interpretation by the

technician. Quest Metrology’s Thread-View

System removes all of these time and production

cost robbing dependencies.

Industry experience makes a

difference

Quest Metrology’s thread systems

are delivering improved operating

safety and product process control to

leaders in major industries.

Aerospace

Aviation Manufacture

Aviation Maintenance

Automotive

Defense

Manufacturing

Industrial Equipment

Paper and Metals

Machining Services

Marine

Medical Technologies

Transportation

You can order now!Want to learn more about our revolutionary thread measurement technologies? Ready to take thread inspection to new levels of ease, accuracy and repeatability? Contact a Quest Metrology representative today at 253-480-2029 or visit us at questmetrology.com

Thread-View System design features and functions are protected under U.S. Patents Nos. 7,227,163, 7,745,805 and 8,039,827. Thread-View® and Thread-View System® are registered trademarks of Quest Metrology, LLC.

World HeadquartersQuest Center

19823 58th Place South, Suite 200

Kent, Washington 98032 USA

(253) 480-2029

Whether the need is to optimize gage

calibration, process control or inventoried

article inspection, the repeating results for

Thread-View System owners are returns on

investment in the form of cost savings, process

efficiency and/or the higher assurance of critical

threaded product performance.

EASY SELF-GUIDED PROCESS: To use the Thread-View System could not be easier: 1. Place the article within the correct size end-augers. 2. Select thread type and measurement parameters through menu, 3. Start program with F4 command, 4. View results on screen. 5. Print calibration report. It is that simple!

Provable Returns!

In our first use of the Thread-

View System, we recovered a

$34,000 payment after proving

inaccuracy of a parts compliance

challenge. Five years later, we

are still getting returns on

investment from its daily use”

Tom Pratt, QA Manager

Precision Aerospace

Doc 3625.3-12.R2