6SECTION 21 -- TRANSMISSIONBOOK 2 - 87015500

Chapter 4 -- Dual Command (Hi--Lo) Transmission-- Calibrations, Fault Finding, Pressure Testing And Limp Home

Procedures

CONTENTS

Section Description Page

21 000 Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Calibrations 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Pressure Testing 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Limp Home Procedure 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Error Codes 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Error Code Fault Finding Flow Diagrams 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 21 -- TRANSMISSION

BOOK 2 - 87015500

Chapter 5 -- Shuttle Command (Mechanical Transmission)

CONTENTS

Section Description Page21 000 Specifications 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tightening Torques 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Special Tools 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Sectional Views 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Description and Operation 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Troubleshooting 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21 114 Mechanical Transmission Housing Removal -- Installation -- Overhaul 13. . . . . . . . . . . . . . .

SECTION 35 -- HYDRAULIC SYSTEMS -- CHAPTER 4

35-57

Error Code 24Perform Hydraulic Lift Calibration

Calibration of Lift Arm Potentiometers and LiftControl Pod

This procedure is required whenever:--

The lift arm position sensing potentiometer, lift controlpod or EDC valve have been replaced.orThe microprocessor has been replaced or its memoryhas been reset using Diagnostic Menu H8. TIA35183

11513. Lower lift arms and disconnect vertical rods from

hanger on automatic pick--up hitch (where fitted).This will allow the lift arms to raise to theirmaximum position.

14. Position raise/work switch to work position.

11615. Turn all the EDC operator controls fully clockwise.NOTE: If the height limit control has not been turnedfully clockwise to the maximum height position, theError Code HL will be displayed.

11716. Start engine and set speed to 1100 rpm.17. Move lift control lever forward and fully lower the

lift.

118

SECTION 31 -- POWER TAKE--OFF -- CHAPTER 2

31-27

55Control Panel Wiring Connections

1. Front P.T.O. Warning Light2. Front P.T.O. Height Limit Control

3. Front P.T.O. Selector Switch

1. Fuse Box -- Front Lift Control Module.

56

1. Steering console Left hand side -- Front PTO ControlModule

57