tms 114 and tms 114t technical manual r manual... · 2019. 7. 23. · aama 2605-05 - voluntary...
TRANSCRIPT
TMS 114/114T
JULY 2019 www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114 AND TMS 114TTECHNICAL MANUAL
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
BLANK PAGE
FEATURES
APPLICATIONS
· TMS 114 (non-thermal) and 114T (thermal barrier) are center set flush glazedsystems that are 4 1/2" deep with a 2" wide sightline
· Glaze from the outside or inside· Screw spline or shear block fabrication· Glazing options up to 1-1/8" thick· Available in anodized and standard or custom painted finishes· Readily available from stock
· Storefront, Punched Openings, or Ribbon Windows· Single span· Integrated entrance framing to allow Pittco standard entrances
or other speciality entrances to be incorporated
SYSTEM PERFORMANCE (TMS 114 Non-Thermal)Description Test Method Allowed Achieved Test Report
Structural ASTM E 330 30 psfAir ASTM E 283 0.06 cfm/ft2 @ 1.57 psf 0.014 cfm/ft2 @ 6.24 psf
Water (Static) ASTM E 331AAMA 501.1
None @ 10 psfNone @ 10 psf
None @ 10 psfNone @ 10 psf
CRF AAMA 1503 N/A 34* 17-02U Value AAMA 1503
NFRC 100N/AN/A
0.82*0.62*
17-0220-01
CR NFRC 500 19* 20-01N/A
N/A
FOR SPECIFIC PRODUCT APPLICATIONS PLEASE CONTACT YOUR PITTCO REPRESENTATIVE
SYSTEM PERFORMANCE (TMS 114T Thermal)Description Test Method Allowed Achieved Test Report
Structural ASTM E 330 30 psfAir ASTM E 283 0.06 cfm/ft2 @ 1.57 psf 0.014 cfm/ft2 @ 1.57 psf
ASTM E 331AAMA 501.1
None @ 10 psfNone @ 10 psf
None @ 10 psfNone @ 12 psf
CRF AAMA 1503 N/A 58* 19-02U Value AAMA 1503
NFRC 100N/AN/A
0.59*0.57*
19-0219-04
SHGC NFRC 200 0.62* 19-04N/A
N/A
* 1" IGU (1/4-1/2-1/4) Clear Annealed Glass, Air Filled, Aluminum Spacer.
Water (Dynamic)
U ValueSHGC NFRC 200 0.62* 20-01N/A
Water (Static)Water (Dynamic)
U Value
CR NFRC 500 N/A 31* 19-04
19-1219-12
19-1219-12
19-1219-12
19-1220-10
Air ASTM E 283 0.06 cfm/ft2 @ 6.24 psf 0.025 cfm/ft2 @ 6.24 psf 19-12
Air ASTM E 283 0.06 cfm/ft2 @ 6.24 psf 0.025 cfm/ft2 @ 6.24 psf 19-12
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
FEATURES
1
SYSTEM PERFORMANCE (TMS 114T Thermal) cont.
CRF AAMA 1503 N/A 58+ 19-09U Value AAMA 1503
NFRC 100N/AN/A
0.40+0.39+
19-0919-07
SHGC NFRC 200 0.25+ 19-07N/A
+ 1" IGU (1/4 solarban 70xl, 1/2 argon filled space with high performance spacer, 1/4 clear glass).
U Value
CR NFRC 500 N/A 31+ 19-07
Description Test Method Allowed Achieved Test Report
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
BLANK PAGE
2
EXPLODED VIEWS PAGE 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4 SIZE DETAILS - TMS 114 NON THERMAL PAGES D1 TO D4. . . . . . . . .
WINDLOAD CHARTS PAGES S1 TO S8. . . . . . . . . . . . . . . . . . . . . . . . . . . . DEADLOAD CHARTS PAGE S9. . . . . . . . . . . . . . . . . . . . . . . . . . . . SECTION PROPERTIES PAGE S10. . . . . . . . . . . . . . . . . . . . . . . . . .
1/4 SIZE DETAILS - TMS 114T THERMAL PAGES D5 TO D8. . . . . . . . . . . . ENTRANCE DETAILS PAGE D9. . . . . . . . . . . . . . . . . . . . . . . . . . . .
THERMAL CHARTS PAGES T1 TO T2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRODUCT DESCRIPTION - THERMAL PAGES 9 TO 13 . . . . . . . . . . . . . . .PRODUCT DESCRIPTION - NON THERMAL PAGES 4 TO 8 . . . . . . . . . . .
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
INDEX
3
● BASIC USES / RELATED USESFraming is designed for flush, center glazed storefront assemblyVertical mullions are typically open back aluminum members, with solid face and flush closure plates forming tubular members for useon single spansHorizontal mullions are of hollow aluminum with removable glazing stopsCorners are configured for 90 and 135 degreesGlazing is insulating glass unit or single pane with adaptersGlass may be transparent, opaque, or decorative typesFraming is intended for one story applicationsFramed assembly may be fitted to most rigid and stable framed opening assemblies
● PRODUCT ATTRIBUTES AND CHARACTERISTICSFraming and glazing stops are designed for glass and panelsWind pressure resistance and pressure equalization are standard within the frame assemblyWeep containment and condensate water collection and drainage to the exterior at concealed weeps are standardIntegral door frames are available
● SELECTION CRITERIAQuality, economy, and good performance are provided at a reasonable costFraming is designed for Interior or exterior environments
● APPLICABLE STANDARDS, RELATED REFERENCESAA (Aluminum Association) - Designation System for Aluminum FinishesAAMA SFM-1-87 - Aluminum Storefront and Entrance ManualAAMA 501.1-05 - Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors using Dynamic PressureAAMA 611-98 - Voluntary Specification for Anodized Architectural AluminumAAMA 1503-98 - Voluntary Test Method for Thermal Transmittance and Condensation Resistance of Windows,Doors, and Glazed Wall SectionsAAMA 2604-05 - Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings onAluminum Extrusions and PanelsAAMA 2605-05 - Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatingson Aluminum Extrusions and PanelsASTM A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
NON-THERMAL PRODUCT DESCRIPTION
4
ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and TubeASTM B221M - Standard Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube [Metric]ASTM E283 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under SpecifiedPressure Differences Across the SpecimenASTM E330 - Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static AirPressure DifferenceASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air PressureDifference
● QUALITY, TESTS, CERTIFICATIONS, AND APPROVALSAir Infiltration: Maximum leakage of 0.02 cfm/sq ft. when measured in accordance with ASTM E283 at a test pressure of 6.24 psfStatic Water Leakage: No uncontrolled leakage, when measured in accordance with ASTM E331 at a test pressure difference of 12.0 psfDynamic Water Leakage: No uncontrolled leakage, when measured in accordance with AAMA 501.1 at a test pressure difference of 12.0 psfStructural Performance: Maximum deflection less than 1/175 of the span length and no damage to the assembly, when measured in accordancewith ASTM E330 at a test pressure of 25 psf
● PACKAGING, HANDLING, AND PROTECTION INSTRUCTIONSPackaged in specially designed heavy cartons or shipped pre-fabricated and assembled
● SPECIAL WARRANTYOne (1) year
● LIMITATIONSNot thermally brokenFraming is limited to applications of one story in heightNot intended for continuous members for multiple floor applications
● SAFETY PRECAUTIONSNormal precautions required
● AVAILABILITYFraming is available in all regions of USA - refer to Internet web site for locations and addresses of distributors
● COSTVaries with elevation, configuration and finish desired
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
NON-THERMALPRODUCT DESCRIPTION
5
PRODUCT PROPERTIES● MATERIAL AND DESIGN
Aluminum: 6063-T6 alloy and temper, to ASTM B221 or ASTM B221MFasteners: Stainless steel, or zinc plated carbon steelPerimeter Anchors: Aluminum, or steel that will be isolated from aluminum componentsGlazing Gaskets: Wedge-type, Ethylene Propylene Diene Monomer (EPDM) rubber with non-stretch cordGlass Stops: Snap-in type
● SHAPE AND DIMENSIONSFrame Size: 2 x 4-1/2 inchGlass Edge Bite: 3/8 inchGlazing Thickness Accepted: 1/8 inch to 1-1/8 inch in increments of 1/16 inch except 7/16 inch, 9/16 inch, 11/16 inch, and 13/16 inch
● SHOP FABRICATION AND ASSEMBLYProvide for flush glazing on all sides with no projecting stopsConfigurations:■ Two-piece snap together mullions■ Solid tubular mullions, assembled to specially designed shear block clipsAccessories:■ Expansion Mullions■ Corner Mullions■ Open Back Perimeter Members■ Integral Door Frames■ Flashing, Subsills■ Head Receptor■ Heavy Duty Mullions■ Standard Steel Reinforcing Available
● COLORS AND TEXTURES■ Architectural anodic coating, in accordance with AAMA 611;
o Aluminum Association Designation.□ AA-M10C22A31 - Class II - (Pittco #42 Clear)□ AA-M10C22A41 - Class I - (Pittco #43 Clear)□ AA-M10C22A44 - Class I - (Pittco #59 Champagne)□ AA-M10C22A44 - Class I - (Pittco #60 Light Bronze)□ AA-M10C22A44 - Class I - (Pittco #61 Medium Bronze)□ AA-M10C22A44 - Class I - (Pittco #62 Dark Bronze)□ AA-M10C22A44 - Class I - (Pittco #63 Black)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
NON-THERMAL PRODUCT DESCRIPTION
6
■ Architectural organic coating, in accordance with AAMA 2604 (50% Kynar 500®);o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2604, High Performance
Organic Coatings on Aluminumo Type: Factory Applied, High Performance, 50% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint manufacturer, and
applied by Paint Manufacturer's Warranty-Approved Applicatoro Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual oxides,
followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminumo Specify color code, e.g. UC 40577(Duranar Black)
■ Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500®);o Finish of Exposed Aluminum shall be compliant with the performance standards set forth in AAMA Specification 2605, Superior Performing
Organic Coatings on Aluminumo Type: Factory Applied, High Performance, 70% Polyvinylidene Fluoride (PVDF) Coating formulated by a licensed paint manufacturer, and
applied by Paint Manufacturer's Warranty-Approved Applicatoro Pretreatment: Applicator to pre-treat the aluminum with solutions to remove organic and inorganic surface soils, remove residual oxides,
followed by a Chrome Phosphate or Chromate Coating to ensure adhesion to the aluminumo Specify color code, e.g. UC 40577(Duranar Black)
PRODUCT PLACEMENT● PREPARATION WORK
Ensure openings are of proper size, and are plumb, square, level and in the proper location and alignment
● INSTALLATIONAlign installed assembly plumb and level, free of warp or twistMaintain dimensional tolerances, aligning with adjacent workSeal joints between framing and building structure watertightFollow guidelines in Pittco Fabrication, Sealant and Erection Brochure
● START-UP AND OPERATIONNot Applicable
● OWNER'S MAINTENANCE INSTRUCTIONSWash surfaces with warm water and mild soap; wipe clean, at least once a year
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
NON-THERMALPRODUCT DESCRIPTION
7
Corporate IdentificationPittco Architectural Metals, Inc
1530 Landmeier RoadElk Grove Village, Illinois 60007Tel: (847) 593-3131Fax: (847) 593-9946Toll-Free: (800) 992-7488Internet: http://www.pittcometals.comE-mail: [email protected]
Technical Services AvailableToll-Free: (800) 992-7488
Classification and FilingMasterFormat
Subset of Section 08410 - Metal Framed StorefrontsUniFormat
Section B2030 - (exterior entrance frames) or C1020 (interior entrance frames)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
NON-THERMAL PRODUCT DESCRIPTION
8
● BASIC USES / RELATED USESFraming is designed for flush, center glazed storefront assemblyVertical mullions are typically open back aluminum members, with solid face and flush closure side plates forming tubular members for use onsingle spansHorizontal mullions are of hollow aluminum with removable glazing stopsGlazing is insulating glass unit or single pane with adaptersCorners are available for 90 and 135 degreesGlass may be transparent, opaque, or decorative typesFraming is intended for one story applicationsFramed assembly may be fitted to most rigid and stable framed opening assemblies
● PRODUCT ATTRIBUTES AND CHARACTERISTICSAluminum frame members are thermally improvedFraming and glazing stops are designed for glass and panelsWind pressure resistance and pressure equalization are standard within the frame assemblyWeep containment and condensate water collection and drainage to the exterior at concealed weeps are standardIntegral door frames are available
● SELECTION CRITERIAQuality, economy, and good performance are provided at a reasonable costFraming is designed for Interior or exterior environments
● APPLICABLE STANDARDS, RELATED REFERENCESAA (Aluminum Association) - Designation System for Aluminum FinishesAAMA SFM-1-87 - Aluminum Storefront and Entrance ManualAAMA 501.1-05 - Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors using Dynamic PressureAAMA 611-98 - Voluntary Specification for Anodized Architectural AluminumAAMA 1503-98 - Voluntary Test Method for Thermal Transmittance and Condensation Resistance of Windows, Doors, and Glazed Wall SectionsAAMA 2604-05 - Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on AluminumExtrusions and PanelsAAMA 2605-05 - Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings onAluminum Extrusions and PanelsASTM A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate [Metric]ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and TubeASTM B221M - Standard Aluminum-Alloy Extruded Bars, Rods, Wires, Profiles, and Tube [Metric]
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
NON-THERMALPRODUCT DESCRIPTION
9
ASTM E283 - Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls and Doors Under SpecifiedPressure Differences Across the SpecimenASTM E330 - Standard Test Method for Structural Performance of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static AirPressure DifferenceASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air PressureDifference
● QUALITY, TESTS, CERTIFICATIONS, AND APPROVALS
Air Infiltration: Maximum leakage of 0.02 cfm/sq ft. when measured in accordance with ASTM E283 at a test pressure of 6.24 psfStatic Water Leakage: No uncontrolled leakage, when measured in accordance with ASTM E331 at a test pressure difference of 12.0 psfDynamic Water Leakage: No uncontrolled leakage, when measured in accordance with AAMA 501.1 at a test pressure difference of 12.0 psfStructural Performance: Maximum deflection less than 1/175 of the span length and no damage to the assembly, when measured in accordancewith ASTM E330 at a test pressure of 25 psfCondensation Resistance Factor (CRF): 58 when measured in accordance with AAMA 1503 with clear 1” insulated glass unit (1/4, 1/2, 1/4)Insulation U-Factor: 0.59 BTU/hr/sq ft/degrees F when measured in accordance with AAMA 1503 with clear 1” insulated glass unit (1/4, 1/2,1/4)
● PACKAGING, HANDLING, AND PROTECTION INSTRUCTIONSPackaged in specially designed heavy cartons or shipped pre-fabricated and assembled
● SPECIAL WARRANTYOne (1) year
● LIMITATIONSFraming is limited to applications of one story in heightNot intended for continuous members for multiple floor applications
● SAFETY PRECAUTIONSNormal precautions required
● AVAILABILITYFraming is available in all regions of USA - refer to Internet web site for locations and addresses of distributors
● COSTVaries with elevation, configuration and finish desired
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
THERMAL PRODUCT DESCRIPTION
10
PRODUCT PROPERTIES● MATERIAL, COMPOSITION AND DESIGN
Aluminum: 6063-T6 alloy and temper, to ASTM B221 or ASTM B221MFasteners: Stainless steel, or zinc plated carbon steelPerimeter Anchors: Aluminum, or steel that will be isolated from aluminum componentsGlazing Gaskets: Wedge-type, Ethylene Propylene Diene Monomer (EPDM) rubber with non-stretch cordGlass Stops: Snap-in typeThermal Barrier: Poured and Debridged Polyurethane and Thermal Slots
● SHAPE AND DIMENSIONSFrame Size: 2 x 4-1/2 inchGlass Edge Bite: 3/8 inchGlazing Thickness Accepted: 1/8 inch to 1-1/8 inch in increments of 1/16 inch except 7/16 inch, 9/16 inch, 11/16 inch, and 13/16 inch
● SHOP FABRICATION AND ASSEMBLYProvide for flush glazing on all sides with no projecting stopsConfigurations:■ Two-piece snap together mullions■ Solid tubular mullions, assembled to specially designed shear block clipsAccessories:■ Expansion Mullions■ Corner Mullions■ Open Back Perimeter Members■ Integral Door Frames■ Flashing, Subsills■ Head Receptor■ Heavy Duty Mullions■ Standard Steel Reinforcing Available
● COLORS AND TEXTURES■ Architectural anodic coating, in accordance with AAMA 611;
o Aluminum Association Designation.□ AA-M10C22A31 - Class II - (Pittco #42 Clear)□ AA-M10C22A41 - Class I - (Pittco #43 Clear)□ AA-M10C22A44 - Class I - (Pittco #59 Champagne)□ AA-M10C22A44 - Class I - (Pittco #60 Light Bronze)□ AA-M10C22A44 - Class I - (Pittco #61 Medium Bronze)□ AA-M10C22A44 - Class I - (Pittco #62 Dark Bronze)□ AA-M10C22A44 - Class I - (Pittco #63 Black)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
THERMALPRODUCT DESCRIPTION
11
■ Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500®);o Finish on exposed aluminum shall be compliant with the performance standards set forth in AAMA 2605, “Superior Performing Organic
Coatings on Aluminum”.o Type: Factory Applied - High Performance, 70% Polyvinylidene Fluoride (PVDF) coating based on Elf Atochem, Inc. Kynar 500® or
Ausimount USA, Inc. Hylar 5000® resin, formulated by a Licensed Paint Manufacturer and applied by the Paint Manufacturer's WarrantyApproved Applicator.
o Pre-treatment: Applicator to pre-treat the aluminum with solutions to remove Organic and Inorganic Surface Soils and Residual Oxides,followed by a Chrome Phosphate Conversion Coating, at a minimum 40 mg/sq ft to ensure adhesion of paint to aluminum.
o Specify color code, e.g. UC 40577(Duranar Black)
■ Architectural organic coating, in accordance with AAMA 2605 (70% Kynar 500®);o Finish on exposed aluminum shall be compliant with the performance standards set forth in AAMA 2604, “High Performance Organic
Coatings on Aluminum”.o Type: Factory Applied - High Performance, 50% Polyvinylidene Fluoride (PVDF) coating based on Elf Atochem, Inc. Kynar 500® or
Ausimount USA, Inc. Hylar 5000® resin, formulated by a Licensed Paint Manufacturer and applied by the Paint Manufacturer's WarrantyApproved Applicator.
o Pre-treatment: Applicator to pre-treat the aluminum with solutions to remove Organic and Inorganic Surface Soils and Residual Oxides,followed by a Chrome Phosphate Conversion Coating, at a minimum 40 mg/sq ft to ensure adhesion of paint to aluminum.
o Specify color code, e.g. UC 40577(Duranar Black)
PRODUCT PLACEMENT● PREPARATION WORK
Ensure openings are of proper size, and are plumb, square, level and in the proper location and alignment
● INSTALLATIONAlign installed assembly plumb and level, free of warp or twistMaintain dimensional tolerances, aligning with adjacent workSeal joints between framing and building structure watertightFollow guidelines in Pittco Fabrication, Sealant and Erection Brochure
● START-UP AND OPERATIONNot Applicable
● OWNER'S MAINTENANCE INSTRUCTIONSWash surfaces with warm water and mild soap; wipe clean, at least once a year
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
THERMAL PRODUCT DESCRIPTION
12
Corporate IdentificationPittco Architectural Metals, Inc
1530 Landmeier RoadElk Grove Village, Illinois 60007Tel: (847) 593-3131Fax: (847) 593-9946Toll-Free: (800) 992-7488Internet: http://www.pittcometals.comE-mail: [email protected]
Technical Services AvailableToll-Free: (800) 992-7488
Classification and FilingMasterFormat
Subset of Section 08410 - Metal Framed StorefrontsUniFormat
Section B2030 - (exterior entrance frames) or C1020 (interior entrance frames)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
THERMALPRODUCT DESCRIPTION
13
HEAD
HORIZONTAL
GLASS STOP
SILL
GLASS STOP
OPEN BACK MULLION
SNAP-IN FILLER
SCREW SPLINE ASSEMBLY
SHEAR BLOCK ASSEMBLY
HEAD
HORIZONTAL
GLASS STOP
SILL
GLASS STOP
OPEN BACK MULLIONSNAP-IN FILLER
THE SCREW SPLINE SYSTEM ALLOWS A FRAME TO BE INSTALLED FROM UNITIZED ASSEMBLIES. SCREWS ARE DRIVENTHROUGH THE BACK OF THE VERTICALS INTO SPLINES EXTRUDED IN THE HORIZONTAL FRAMING MEMBERS. INDIVIDUALUNITS ARE THEN SNAPPED TOGETHER TO FORM A COMPLETE FRAME
THE SHEAR BLOCK METHOD OF FABRICATION IS AN ALTERNATE METHOD OF FABRICATION. HORIZONTALSARE ATTACHED TO THE VERTICAL MULLIONS WITH SHEAR BLOCKS. THIS METHOD MUST BE USED WITHTUBULAR VERTICAL MULLIONS.
SHEAR BLOCK
SHEAR BLOCK
SHEAR BLOCK
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
EXPLODED VIEW
14
3
4
5
1 2
2"T
YP
ICA
L
412"
TYPICAL
2"T
YP
ICA
L
412"
TYPICAL
2"TYPICAL
41 2"
TY
PIC
AL
2"TYPICAL
41 2"
TY
PIC
AL
SCREW SPLINE SHEAR BLOCK
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
20-028 (JAMB)20-168 (PERIMETER FILLER)
20-028 (JAMB)20-029 (GLAZING FILLER)
20-028 (JAMB)20-168 (PERIMETER FILLER)
20-028 (JAMB)20-029 (GLAZING FILLER)
20-028 (HEAD)20-168 (PERIMETER FILLER)
20-039 (HORIZONTAL)19-031 (GLASS STOP)
20-030 (SILL)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)20-000 (SUB-SILL)
20-028 (HEAD)20-168 (PERIMETER FILLER)19-034 (SHEAR BLOCK)
20-039 (HORIZONTAL)19-031 (GLASS STOP)19-040 (SHEAR BLOCK)
20-030 (SILL)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)20-000 (SUB-SILL)19-041 (SHEAR BLOCK)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
NON-THERMALTYPICAL FRAMING DETAILS (Outside Glazed)
D1DETAILS
3
4
5
1 2
SCREW SPLINE SHEAR BLOCK
2"TYPICAL
41 2"
TY
PIC
AL
2"TYPICAL
41 2"
TY
PIC
AL
2"T
YP
ICA
L
412"
TYPICAL
2"T
YP
ICA
L
412"
TYPICAL
20-028 (JAMB)20-168 (PERIMETER FILLER)
20-028 (JAMB)20-029 (GLAZING FILLER)
20-028 (JAMB)20-168 (PERIMETER FILLER)
20-028 (JAMB)20-029 (GLAZING FILLER)
20-030 (HEAD)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)
20-039 (HORIZONTAL)19-031 (GLASS STOP)
20-028 (SILL)20-168 (PERIMETER FILLER)20-000 (SUB-SILL)
20-030 (HEAD)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)19-041 (SHEAR BLOCK)
20-039 (HORIZONTAL)19-031 (GLASS STOP)19-040 (SHEAR BLOCK)
20-028 (SILL)20-168 (PERIMETER FILLER)20-000 (SUB-SILL)19-034 (SHEAR BLOCK)
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
NON-THERMAL TYPICAL FRAMING DETAILS (Inside Glazed)
D2DETAILS
412"
41 2"
16-705 19-047
2 PIECE NO POCKET CORNER 1 POCKET CORNER
19-047
20-043
19-047
20-042
20-043
20-04420-043
20-042
2 POCKET CORNER 90° CORNER 90° CORNER
20-042
20-043
3 POCKET CORNER 4 POCKET CORNER 135° CORNER
17-4
62
20-029
ADJUSTABLE MULLION
20-14020-141
19-047
20-043
20-042
20-029
412" x 41
2" TUBE
(ADJUSTABLE FROM 0 TO 90 DEGREES)
(SCREW SPLINE OR SHEAR BLOCK FABRICATION) (SHEAR BLOCK FABRICATION ONLY)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
NON-THERMALCORNER DETAILS
D3DETAILS
20-028
20-02916-500
20-139
20-029
20-038
20-032
19-04519-183 19-168
17-349
20-139
20-029
20-032
20-186
214"
19-102 20-101
19-152
20-095
20-029
19-03119-031
20-095
19-03119-031
20-097
STANDARD MULLION w/OPTIONAL STEEL
16-501
HEAVY WALL MULLION HEAVY WALL MULLIONw/
OPTIONAL STEEL
TUBULAR MULLION EXPANSION MULLION
14" SNAP IN
GLAZING ADAPTER
12" SNAP IN
GLAZING ADAPTER
FULL LENGTHFLAT FILLER
SNAP INPOCKET FILLER
SLIDE INDOOR STOP
HEAD RECEPTOR
412 " x 41
2" HORIZONTAL 412" SILL
16-142
OPTIONAL SILL FLASHINGS
NARROW SIDELITE BASE
30-105
17-021
30-18430-184
20-000
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
NON-THERMAL MISCELLANEOUS DETAILS
D4DETAILS
3
4
5
1 2
2"T
YP
ICA
L
412"
TYPICAL
2"T
YP
ICA
L
412"
TYPICAL
41 2"
TY
PIC
AL
2"TYPICAL
41 2"
TY
PIC
AL
SCREW SPLINE SHEAR BLOCK
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
19-028 (JAMB)20-168 (PERIMETER FILLER)
19-028 (JAMB)19-029 (GLAZING FILLER)
19-028 (JAMB)20-168 (PERIMETER FILLER)
19-028 (JAMB)19-029 (GLAZING FILLER)
19-028 (HEAD)20-168 (PERIMETER FILLER)
19-039 (HORIZONTAL)19-031 (GLASS STOP)
19-030 (SILL)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)
19-028 (HEAD)20-168 (PERIMETER FILLER)19-034 (SHEAR BLOCK)
19-039 (HORIZONTAL)19-031 (GLASS STOP)19-040 (SHEAR BLOCK)
19-030 (SILL)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)19-041 (SHEAR BLOCK)
2"TYPICAL
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
THERMALTYPICAL FRAMING DETAILS (Outside Glazed)
D5DETAILS
3
4
5
1 2
SCREW SPLINE SHEAR BLOCK
2"T
YP
ICA
L
412"
TYPICAL
2"T
YP
ICA
L
412"
TYPICAL
2"TYPICAL
41 2"
TY
PIC
AL
2"TYPICAL
41 2"
TY
PIC
AL
19-028 (JAMB)20-168 (PERIMETER FILLER)
19-028 (JAMB)19-029 (GLAZING FILLER)
19-028 (JAMB)20-168 (PERIMETER FILLER)
19-028 (JAMB)20-029 (GLAZING FILLER)
19-030 (HEAD)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)
19-039 (HORIZONTAL)19-031 (GLASS STOP)
19-028 (SILL)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)
19-030 (HEAD)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)19-041 (SHEAR BLOCK)
19-039 (HORIZONTAL)19-031 (GLASS STOP)19-040 (SHEAR BLOCK)
19-028 (SILL)20-168 (PERIMETER FILLER)19-000 (SUB-SILL)19-034 (SHEAR BLOCK)
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
2VERTICAL
1JAMB
3HEAD
4HORIZONTAL
5SILL
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
THERMAL TYPICAL FRAMING DETAILS (Inside Glazed)
D6DETAILS
412"
41 2"
16-705 19-047 19-047
19-043
19-047
19-042
19-043
19-04419-043
19-042
19-042
19-043
19-4
62
19-029
19-14019-141
19-047
19-043
19-042
19-029
2 PIECE NO POCKET CORNER 1 POCKET CORNER
2 POCKET CORNER 90° CORNER 90° CORNER
3 POCKET CORNER 4 POCKET CORNER 135° CORNER
ADJUSTABLE MULLION
412" x 41
2" TUBE
(ADJUSTABLE FROM 0 TO 90 DEGREES)
(SCREW SPLINE OR SHEAR BLOCK FABRICATION) (SHEAR BLOCK FABRICATION ONLY)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
THERMALCORNER DETAILS
D7DETAILS
19-028
19-029
19-139
19-029
19-038
19-032
19-04519-183 19-168
17-349
19-032
19-029
214"
19-102 19-101
19-152 16-142
19-095
19-029
19-03119-031
19-095
19-03119-031
19-097
19-139
* NARROW SIDELITE BASE IS NON-THERMAL*
STANDARD MULLION w/OPTIONAL STEEL
HEAVY WALL MULLION HEAVY WALL MULLIONw/
OPTIONAL STEEL
TUBULAR MULLION EXPANSION MULLION
14" SNAP IN
GLAZING ADAPTER
12" SNAP IN
GLAZING ADAPTER
FULL LENGTHFLAT FILLER
SNAP INPOCKET FILLER
HEAD RECEPTOR
412 " x 41
2" HORIZONTAL 412" SILL NARROW SIDELITE BASE
16-50016-501
OPTIONAL SILL FLASHINGS
30-105
17-021
30-18430-184
19-000
20-186
SLIDE INDOOR STOP
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
THERMAL MISCELLANEOUS DETAILS
D8DETAILS
2"T
YP
ICA
L
412"
TYPICAL1
TRANSOM HEAD
2DOOR HEAD
3BOTTOM RAIL
19-030 (HEAD)19-031 (GLASS STOP)20-168 (PERIMETER FILLER)
19-130 (TRANSOM HEAD)19-131 (SHEAR BLOCK)
SINGLE ACTING
1
2
3
76
54
10
3
98
DOUBLE ACTING
SINGLE ACTINGDOOR JAMBS
DOUBLE ACTINGDOOR JAMBS
41 2"
TY
PIC
AL
10SINGLE ACTING
HEADER
10DOUBLE ACTING
HEADER
619-036 OR 19-177
(MULLION)w/ 19-099 (TRANSOM INSERT)
TRANSOM JAMBSTransom area for both double or single acting doors withglass surround. Jambs above transom bar are routed outto accept glass holding insert with or without steel reinforcing.
19-130 (TRANSOM HEAD)19-131 (SHEAR BLOCK)
819-177 (MULLION)
919-177 (MULLION)
419-036 (MULLION)
519-036 (MULLION)
719-036 OR 19-177
(MULLION)w/ 19-099 (TRANSOM INSERT)
12-140 (TRANSOM HEAD)19-131 (SHEAR BLOCK)14-090 (SASH)
12-140 (TRANSOM HEAD)19-131 (SHEAR BLOCK)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
ENTRANCE DETAILS
D9DETAILS
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
BLANK PAGE
D10
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
20-02820-029
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
20-02820-029
WITH 16-500 STEEL
VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.
A
B
CD
E
A
B
C
D
E
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
NON-THERMALWINDLOAD CHARTS
S1
20-13920-029
20-13920-029
WITH 16-501 STEEL
VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.
A
BCD
E
A
B
C
D
E
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
NON-THERMAL WINDLOAD CHARTS
S2
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
20-038
20-03220-032
COMBINED SECTIONS ARE ANALYZED AS AN ASSEMBLY
A
BCD
E
A
B
C
D
E
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
NON-THERMALWINDLOAD CHARTS
S3
19-02819-029
19-02819-029
WITH 16-500 STEEL
VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.
A
B
CD
E
A
B
C
D
E
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
THERMAL WINDLOAD CHARTS
S4
19-13919-029
19-13919-029
WITH 16-501 STEEL
VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.
A
B
CD
E
A
B
C
D
E
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
THERMALWINDLOAD CHARTS
S5
19-038
19-03219-032
COMBINED SECTIONS ARE ANALYZED AS AN ASSEMBLY
A
BCD
E
A
B
C
D
E
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
THERMAL WINDLOAD CHARTS
S6
19-036
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
A
B
CD
E
19-03616-500
VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.
A
B
C
D
E
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
WINDLOAD CHARTS
S7
19-177
SYSTEM ANALYSIS CRITERIA:
DEFLECTION LIMITS: L/240 + 1/4" FOR SPANS GREATER THAN 13'-6"
CODES AND SPECIFICATIONS VARY, NO SINGLE LITE OF GLASS SHALL DEFLECT MORE THAN 3/4"
L/175 FOR SPANS LESS THAN 13'-6"
LATERAL BRACING OR HORIZONTAL MEMBER SPACING: 48" O.C. (MAXIMUM)
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
(FOR HORIZONTAL SPACING GREATER THAN 48" CONTACT PITTCO ENGINEERING)
A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THERMAL BREAK
A = 15 PSFB = 20 PSFC = 25 PSFD = 30 PSFE = 40 PSF
A
B
CD
E
19-17716-500
VERTICAL REINFORCING IS ANALYZED AS AN ASSEMBLY WITH THE ALUMINUMSECTIONS.
A
B
C
D
E
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
WINDLOAD CHARTS
S8
20-039 (HORIZONTAL)19-031 (GLASS STOP)
20-030 (HORIZONTAL)20-029 (GLAZING FILLER)19-031 (GLASS STOP)
19-039 (HORIZONTAL)19-031 (GLASS STOP)
19-030 (HORIZONTAL)19-029 (GLAZING FILLER)19-031 (GLASS STOP)
A = SETTING BLOCKS AT 1/8 POINTSB = SETTING BLOCKS AT 1/4 POINTS
SYSTEM ANALYSIS CRITERIA:
SECTION EVALUATED PER 2005 ALUMINUM DESIGN MANUALSIMPLE SPAN CONDITION
ALUMINUM: 6063-T6
A 15% REDUCTION IN SECTION PROPERTIES TO ACCOUNT FOR THE THERMAL BREAK THERMAL SECTIONS
HORIZONTAL OR DEADLOAD LIMITATIONS ARE BASED UPON 1/8" MAXIMUM ALLOWABLE DEFLECTION WITH 1" THICK INSULATED GLASS
AB
AB
AB
AB
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
DEADLOAD CHARTS
S9
STRUCTURAL PROPERTIES of TMS 114 NON-THERMAL FRAMINGPart Number Ix Sx Iy Sy
12-140 3.993 1.774 1.102 1.10216-500 (Steel) 1.093 0.547 0.024 0.04216-501 (Steel) 0.649 0.316 0.032 0.076
16-705 6.984 3.104 6.984 3.10417-462 3.511 1.145 1.667 0.65419-036 3.380 1.470 0.887 0.62819-047 1.881 0.563 1.947 0.59619-130 4.047 1.795 1.050 0.74419-177 3.412 1.508 0.846 0.79220-028 2.804 1.196 0.404 0.31520-030 2.133 0.822 0.296 0.27420-032 2.257 1.001 0.164 0.16620-038 3.000 1.325 0.679 0.66920-039 2.445 1.021 0.458 0.38920-042 2.287 0.756 2.274 0.73720-043 2.338 0.764 1.847 0.56520-044 2.333 0.775 1.809 0.54320-095 4.630 2.059 2.163 0.96420-139 6.688 2.889 0.663 0.56920-140 1.869 0.810 0.074 0.08520-141 2.138 0.877 0.180 0.133
STRUCTURAL PROPERTIES of TMS 114T THERMAL BARRIER FRAMINGPart Number Ix Sx Iy Sy
19-029 0.649 0.316 0.032 0.07619-036 3.380 1.470 0.887 0.62819-047 1.881 0.563 1.947 0.59619-028 2.084 1.196 0.404 0.31519-030 2.133 0.822 0.296 0.27419-032 2.257 1.000 0.163 0.16619-038 2.995 1.321 0.678 0.66819-039 2.445 1.021 0.458 0.38919-042 2.287 0.756 2.274 0.73719-043 2.338 0.764 1.847 0.56519-044 2.333 0.775 1.809 0.54319-095 4.630 2.059 2.163 0.96419-139 6.688 2.889 0.663 0.56919-140 1.869 0.810 0.074 0.08519-141 2.138 0.877 0.180 0.13319-168 0.508 0.243 0.012 0.01519-177 3.412 1.508 0.846 0.79219-462 3.511 1.145 1.667 0.654
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
SECTION PROPERTIES
S8
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
THERMAL CHARTS
T1FOR INSTRUCTIONS ON HOW TO READ THERMAL CHARTS PLEASE SEE GENERAL SECTION OF THE CATALOG
www.pittcometals.com
ARCHITECTURAL METALS, INC.
TMS 114/114T
JULY 2019
TMS 114/114T
JULY 2019
THERMAL CHARTS
T2FOR INSTRUCTIONS ON HOW TO READ THERMAL CHARTS PLEASE SEE GENERAL SECTION OF THE CATALOG