tollos 2015 e-planning guide

36
TOLLOS PLANNING GUIDE U.S. Corporate Office 1 Easter Court, Suite J Owings Mills, MD 21117 410.363.1515 PHONE 888.363.7224 TOLL FREE Canadian Office 75 Dyment Road Barrie Ontario L4N 3H6 705.733.0022 PHONE 888.363.7224 TOLL FREE www.tollos.com Formerly T.H.E. Medical Architects Equipment Planners Contractors SPH Coordinators

Upload: karen-mullervy

Post on 11-Apr-2017

714 views

Category:

Documents


2 download

TRANSCRIPT

TOLLOS PLANNING GUIDE

U.S. Corporate Office

1 Easter Court, Suite J

Owings Mills, MD 21117

410.363.1515 PHONE

888.363.7224 TOLL FREE

Canadian Office

75 Dyment Road

Barrie Ontario L4N 3H6

705.733.0022 PHONE

888.363.7224 TOLL FREEwww.tollos.com

Formerly T.H.E. Medical

• Architects• Equipment Planners• Contractors• SPH Coordinators

Table of Contents

Introduction to Tollos ® 3

Tollos ® Advanced Technology 4

Tollos ® Ceiling Lift Advantages 5

Architectural and Technical Information 6

Ceiling Lift Motor Specifications and Detail Drawings 15

Tollos ® Product Range 29

Tollos is the leading safe patient handling (SPH) company dedicated to patient safety, employee safety and hygiene. Tollos was formed in 1989, headquartered in Baltimore, Maryland; manufactures lifting equipment in Barrie, Ontario; and manufactures bathing equipment in Sparta, Tennessee. Tollos is ISO certified, uses automotive-based design and manufacturing practices and has had zero recalls.

Tollos SPH products consist of state-of-the-art ceiling lifts and floor lifts with a complimentary full-line of slings. Proprietary industry leading features include a patent pending, industry only wipe-down Infection Control Strap, iQ Technology, Wi-Fi, wireless hand controls and integrated scale, among other features.

Equally important, Tollos’ ceiling and floor lifts have the longest industry useful life due to high efficiency motor designs. This in turn allows every other year preventative maintenance and extended battery life, resulting in the lowest cost of ownership.

All of these features are coupled with turnkey installation and training along with a cash back ROI guarantee program. From providing on-site assessments for both equipment and design selection recommendations to installation and track configuration options, Tollos is your one-stop shop allowing you to seamlessly implement a SPH program and capture all of the intended benefits. All at very cost-effective pricing.

We are your SPH specialist. We manufacture in North America, have state-of-the-art equipment at competitive pricing, a comprehensive training and installation program, and have the resources and experience to help you implement an excellent program with 24/7 support during and after installation and training.

Pictured (top to bottom) is our Cirrus Ceiling Lift, Infection Control Strap and

an example of flush-mounted track with crosser rail

Introduction to Tollos®

3

Tollos® Ceiling Lift Advantages

Cost Savings

A combination of Tollos Advanced Technology features will provide you with extreme cost of ownership savings over other manufacturers. Savings will be recognized in the Life Cycle of the Lift, Preventative Maintenance Requirements and Battery Life.

Example of Guaranteed Lowest Ownership Costs

Life Cycle

Our ceiling lift motors will have a useful life of 25,000 cycles. This compares to major competitors stating their lifts useful life run between 10,000-15,000 cycles. That can translate into a Tollos lift outlasting the competition by 2.5 times. The life of the lift is often overlooked, so please consider that the Tollos lift will keep on running while the competitions product will need to be replaced. This saves significant costs over time.

Preventative Maintenance (PM)

Tollos lifts only require full preventative maintenance every TWO YEARS. The competition requires a PM every 6 months to 1 year. At an average estimated cost of $300 per motor PM, this cost savings is impactful to a facility’s operating costs. Not only does it save a facility the cost of the PM, it saves time and hassle on organizing room availability when census is high, moving patients, and eliminates all the time it takes to plan and coordinate the PM’s. Tollos recommends a simple safety check on the PM off years that is inexpensive, quick and can be performed with the patient in the room. Tollos will also train the facility to do their own PM’s if the facility chooses.

Battery Life

Tollos has introduced battery saving software mechanisms that will extend the life of your battery far beyond competitive lift batteries. This software translates into cost savings by reducing the need to replace batteries in your lift less often. Tollos also uses non-proprietary batteries, which means we will provide you with the model number of the battery and you can arrange to purchase them from your local supplier.

Training and Education – Value Add

Unlike other lift manufacturers, Tollos offers a complete training and education support system to maximize compliance in your facility…at no charge! As a valued Tollos partner, we will provide you with expert clinical support, online learning modules, interactive web streams, product guides, program materials and more…Everything you need to provide your staff with the tools necessary to feel comfortable and competent in operating lift equipment.

Competitor 1 Competitor 2 TollosSaving over life

(Competitor 1)

Saving over life

(Competitor 2)

PM Schedule 6-12 months 12 months 24 months$1,500 (50% less over useful life)

$2,000 (50% less over useful life)

Battery Warranty 12 months 12 months 24 months

$125 $125

Strap Warranty 12 months 12 months 24 months

Useful Life 15,000 cycles 10,000 cycles 25,000 cycles$1,047 (67%

longer)$5,000 (2.5 times

longer)

NET SAVINGS $3,032 $7,125

Tollos® Advanced Technology

4

Unique Product Features

IC Strap

Our Patent Pending Infection Control Strap (IC) is non-porous and easily cleanable unlike the woven ceiling lift straps on the market. C-Diff spores for example are killed utilizing a 10% bleach solution. Using this compound on standard woven lift straps will decrease the life of the strap and can present safety hazards. With the Tollos IC, you simply spray or wipe the strap with your hard surface disinfectant cleaner and follow your infection control guidelines.

Recessed Track with WINGS Advantages

Recessed track with Wings provides an aesthetically pleasing look and fast coordination of ceiling tile installation. This style track eliminates the need to adhere to an “L” channel tile grid to parallel tracks and manually cut tiles for perfect alignment – this saves installation time! Since the track is flush with the ceiling grid, it provides an increased lifting height and can be coordinated with most ceiling lift protrusions such as booms, lights, etc.

Six-Point Spreader Bar

• Supine Lifting - Lift entire patient off the bed to reposition, change sheets, lateral transfer. Patient is completely off the bed.

• Patient Comfort – Eliminates larger patients feeling constricted; eliminates pressure on chest for easier breathing.

• Staff Communication – Allows for direct eye contact and communication from caregiver to patient when care giver is standing to the side of the patient.

• Versatility – Provides functional use for ALL SPH tasks including Seated, Lateral, Supine, Repositioning, Limb Lifting, Turning, Ambulation

Design Solutions

Tollos’ strength in Design Solutions to builders, architects and contractors is invaluable when coordinating unique and challenging floor plans. An example of this is shown in the image to the right. A synergistic environment was created between the lift system and the casework, in this case, millwork. Tollos offers limitless solutions and invites its customers to present such projects to accomplish the best solution for everyone on the project.

Sling Compatibility

Tollos utilizes Loop style lift slings. These slings can be used on competitor’s lifts. We also authorize your facility to utilize your existing non-Tollos sling with our lift bar with prior approval.

Motor Compatibility

The Tollos ceiling lift motor has the ability to fit in your existing lift tracks if necessary. When it’s time to replace your current motors, or add motors to existing rail, the process of hanging a Tollos motor is simple, fast and affordable.

Tollos® Ceiling Lift Advantages

5

PARALLEL

SUPPORT

RAILS

GATE

TURNTABLE

LIFT MOTOR

CROSSER RAIL

(TRAVERSE RAIL)

Ceiling Lift System Terminology

Architectural and Technical Information

6

SINGLE STRAIGHT TRACK X-Y SYSTEM TRACK

Ceiling Lift Room Coverage

Architectural and Technical Information

7

A rail system comprises one or more rails, which are installed on the ceiling, the wall, or on wall supports.  The rail system may be designed by using one or more of the methods shown here.

Straight and J-Curve Track Design

• Typically least costly

• Quickest install time (typically)

• Very limited use of lift for repositioning and turning in bed

• Not recommended solution

X-Y Systems

• Full floor coverage underneath side rails

• Multiple transfer points

• Use of lift for repositioning and turning in bed

• Very useful which increases compliance and improves patient outcomes

• Can connect to gate system and allow greater room coverage

STRAIGHT TRACK J-CURVE TRACK

X-Y SYSTEM

WALL-MOUNTED

X-Y SYSTEM

X-Y SYSTEM WITH

GATE INTO TOILET

X-Y SYSTEM WITH

GATE & TURNTABLE IN

BATHROOM

Rail Systems

Architectural and Technical Information

8

PARALLEL

SUPPORT

RAILS

CURTAIN PASS

THROUGH

TRAVERSE

RAIL

SPREADER

BAR

LIFT

MOTOR

Architectural and Technical Information

Design Considerations

Tollos provides expertise in design considerations in planning retrofit installations. Note in the pictures below the various hospital room equipment that needs to be planned for in the ceiling grid.

9

G2 STANDARD RAIL

Rail Options

G2 STANDARD RAIL

WITH WINGS

STANDARD SINGLE RAIL STANDARD SINGLE RAIL

WITH WINGS

G3 HEAVY DUTY

RAIL

G3 HEAVY DUTY RAIL

WITH WINGS

D2 DOUBLE-HIGH

HEAVY-DUTY RAIL

Standard Curve Types

90O CURVE TRACK

36 RADIUS

90O CURVE TRACK

30 RADIUS

90O CURVE TRACK

36 RADIUS

90O CURVE TRACK

30 RADIUS

Architectural and Technical Information

10

Turntables

Manual

• Operated manually by pulling cord (one to open and one to close)

• Allows 90 degree turns

• Can turn every 22.5 degrees

• Can have up to .16 different turn ports

• Generally good for tight spaces like bathrooms.

Electric

• Powered version turns by a motor operated by hand control.

• Can turn every 45 degrees for up to six different ports.

• No inconvenience or noise from pull cords

• Motor hand control can operate turntable (and gate if applicable)

• Power is typically supplied via hard -wiring above ceiling.

• This requires compliance with local electrical codes and electrician must supply power to junction box with low voltage output to turntable

• More expensive but move convenient

Gates

Automatic

• The Auto Gate is engineered for both easy setup/installation as well as easy use by combining the best features of an electric gate with the simplicity of a manual design

• The Auto Gate eliminates the need for hard wiring and the related electric code issues, eliminates most drilling yet still eliminates cords on old style manual gates. Fewer moving parts also means enhanced durability.

Electric

• Powered gate is easier to align and is ideal for higher weight rooms (750lb to 1,000lb rooms).

• It can use the same hand control as the motor and turntable.

• Gates require stiffer crosser track.

• Like the powered turntable, the powered gate requires electric hard wired above the ceiling in compliance with local codes.

Architectural and Technical Information

11

Trolleys

Gantry Track Trolleys

• “Blade” style gantry trolley with Continuous charge contact

• “Blade style gantry trolley with docking style contact

Lift Motor Trolleys

• Quick release Cirrus®/Pinnacle® trolley

• Improved 3 wheel Stratus® trolley

• 6 axle extended trolley for curtain jumps

• 2 piece trolley for Quick Curves

Charger Docks & CC Wheels

DOCKING CHARGER CC RAIL CHARGER GANTRY TROLLEY CC

CONTACT WHEELS

Track End Stops and End Cap Vinyl

RUBBER END STOP WITH SHOULDER BOLT & CAPS VINYL END CAP COVERS

Architectural and Technical Information

12

Strut and Bracers

• 1 5/8” x 1 5/8” Strut with holes

• 1 5/8” x 3 1/4” Strut with holes

• 1 5/8” x 7/8” Strut with holes

Straight Track and Parallel Rail Clamps

• 3” Standard Rail Bracket for straight track installation

• 6” Rail Bracket for joints, wall mounts, & gate installation

Wedge Anchors and Threaded Rod

• Redhead ½” x 5 ½” Wedge Anchor

• Redhead ½” x 3 ¾” Wedge Anchor

• ½”-13 x 10’ Threaded Rod

Fasteners and Hardware

• 1/2”-13 Regular Spring Nut

• 1/2” Flat Washer

• 1/2” Lock Washer

• Hex Cap Screws (1/2-13 X 1”, 1 ½”, 2”)

• 1/2” x 1 3/4” Coupler

• 1/2” Square Washer

• 1/2” Hex Nut

Beam Clamps and Corner Braces

• 1 5/8” Beam Clamps

• 3 1/4”Beam Clamps

• 6 1/2” Beam Clamp

• 2-Hole Corner Angle

Architectural and Technical Information

13

ABOVE CEILING SUPPORT

RECESSED RAIL RECESSED INTO LIFT STORAGE CABINET

Architectural and Technical Information

UNISTRUT TO BRIDGE DUCTS

14

Ceiling Lift Motor Specifications and Detail

Fixed Ceiling Lift Drop Height Dimension

15

Ceiling Lift Motor Specifications and Detail

450 lb. motor and track

1. Ceiling Track System

• The Ceiling Track shall be made from high strength extruded aluminum T6061-T6 at a minimum thickness of 3/16” (4.8mm)

• The Track System shall be compatible for Continuous Charge or an in line docking station

2. Lift Unit

• The Lift Unit shall be constructed of a steel frame system (2205lbs / 1000kg tested) driven by a gear reduced high torque motor

• Lift unit must be in compliance with IEC60601-1

• The Lift system shall have the following salient characteristics.

• Lifting capacity: up to 450lb using a single motor and single lifting strap

• Electronic soft-start and soft-stop motor control

• Emergency lowering device (without needing any special tool)

• Emergency stopping device

• Current limiter for circuit protection in case of overload.

• Safety device that stops the motor to lift when batteries are low.

• Lifting speed: 1.08in/s (2.75 cm/s), in full capacity

• Horizontal displacement speed: 4.7 in/s (120mm/s)- when applicable

• Emergency brake (in case of mechanical failure)

• Strap length up to 90in (2.3m) tested for 2998lbs (1360kg)

• Entire external system (track, motor, strap, hanger, etc.) shall be able to be cleaned according to infection control standards without the loss of strength and integrity of the system.

• Cab: All metal enclosure

• Handheld remote control (wired or wireless)

• Lifting strap must be made of non-porous/non-woven material for infection control cleaning precautions.

• Quick release trolley (except where curves or gates require other trolley)

• Dual controls on motor

• Digital display on motor with major data indicators scrolling consisting of cycle counter, PM counter and alert, low battery charge operation, battery level and system check

2. Spreader bar

• 6 point with spring loaded locking clips to secure sling loops

• Spreader bar must work for all lift and transfer tasks (i.e. Seated, supine, repositioning, turning, walking, hygiene and limb lifting)

4. Motors

• Vertical Movement-DC Motor

• Type: fully enclosed, permanent magnet.

• Rating: 24Vdc, 110W, 4000RPM, 0.3N-m.

• Mounting: Secured to chassis.

• Motors safe to use in wet areas (GFCI protected).

• Horizontal Movement-DC Motor when applicable

• Type: Fully enclosed, permanent magnet, integral reducer.

• Rating: 24Vdc, 62W, 260RPM, 1.0N-m.

• Mounting: Secured to chassis.

• Electrical supply will be from the junction box located in the ceiling. A dedicated 20 Amp, 120 Volt, single-phase circuit will serve 2 patient lifts.

• Motor must not require a full PM before 3 years or 4000 lift cycles

5. Batteries

• The batteries shall be of deep discharge construction and must be non-proprietary

• System shall be capable of using batteries of same voltage and amp rating by different manufacturer without voiding the warranty.

16

Ceiling Lift Motor Specifications and Detail

6. Charger

• Charger Input: 100-240 Vac, 60 Hz.

• Charger Output: 27 Vdc, 1 A max.

7. Slings

• The straps shall be made of threaded nylon. The straps shall ensure the patient’s safety by preventing the patient from falling out of the sling.

• The sling shall be made from a polyester/nylon net material that is pliable, breathable and easy to use. The sling shall cradle the body of the patient without destruction of tissue at the contact points.

• Capable of using disposable slings or disposable covers for the slings.

• Capable of using 3rd party slings without voiding the warranty.

8. Other System Requirements

• The system shall operate in a smooth, consistent manner without any fast, slow, or jerky starts and stops.

• Emergency Lowering: Shall not require any special tools

• Capable of adding scale to system to determine patient’s weight. Capable of having an integrated scale

• The vendor shall have 24/7 telephone support staffed in the United States.

• No history of recalls.

• Disclosure of all Tort claims against vendor either pending or resolved.

9. Installation

• Install ceiling mounted patient lift system as per manufacturer’s instruction and under the supervision of manufacturer’s qualified representative.

• Contractor shall provide all labor, materials, tools, equipment, etc. required for the installation.

10. Test

• Conduct a performance test on each lift system to show that the patient lift system equipment and control devices operate properly and in accordance with design and specification requirements.

• Contractor shall provide certifications for each lift system with the room number and building including a date and time and load tested.

• Equipment certified after install. Certification shall include weight test of maximum lift capacity plus 25% at the attachment point, otherwise 100% SWL. If the system fails, contractor will make all necessary adjustments and re-test within 7 business days.

11. Warranty

• The contractor shall provide a one year warranty on all parts and labor. The warranty shall include all travel and shipping costs associated with any warranty repair. The motor shall have a three year warranty.

450 lb. motor and track (cont.)

17

600 lb. motor and track

1. Ceiling Track System

• The Ceiling Track shall be made from high strength extruded aluminum T6061-T6 at a minimum thickness of 3/16” (4.8mm)

• The Track System shall be compatible for Continuous Charge or an in line docking station

2. Lift Unit

• The Lift Unit shall be constructed of a steel frame system (2205lbs / 1000kg tested) driven by a gear reduced high torque motor

• Lift unit must be in compliance with IEC60601-1

• The Lift system shall have the following salient characteristics.

• Lifting capacity: up to 600lb using a single motor and single lifting strap

• Electronic soft-start and soft-stop motor control

• Emergency lowering device (without needing any special tool)

• Emergency stopping device

• Current limiter for circuit protection in case of overload.

• Safety device that stops the motor to lift when batteries are low.

• Lifting speed: 0.75in/s (1.9 cm/s), in full capacity

• Horizontal displacement speed: 4.7 in/s (120mm/s)- when applicable

• Emergency brake (in case of mechanical failure)

• Strap length up to 90in (2.3m) tested for 2998lbs (1360kg)

• Entire external system (track, motor, strap, hanger, etc.) shall be able to be cleaned according to infection control standards without the loss of strength and integrity of the system.

• Cab: All metal enclosure

• Handheld remote control (wired or wireless)

• Lifting strap must be made of non-porous/non-woven material for infection control cleaning precautions.

• Quick release trolley (except where curves or gates require other trolley)

• Dual controls on motor

• Digital display on motor with major data indicators scrolling consisting of cycle counter, PM counter and alert, low battery charge operation, battery level and system check

2. Spreader bar

• 6 point with spring loaded locking clips to secure sling loops

• Spreader bar must work for all lift and transfer tasks (i.e. Seated, supine, repositioning, turning, walking, hygiene and limb lifting)

4. Motors

• Vertical Movement-DC Motor

• Type: fully enclosed, permanent magnet.

• Rating: 24Vdc, 110W, 4000RPM, 0.3N-m.

• Mounting: Secured to chassis.

• Motors safe to use in wet areas (GFCI protected).

• Horizontal Movement-DC Motor when applicable

• Type: Fully enclosed, permanent magnet, integral reducer.

• Rating: 24Vdc, 62W, 260RPM, 1.0N-m.

• Mounting: Secured to chassis.

• Electrical supply will be from the junction box located in the ceiling. A dedicated 20 Amp, 120 Volt, single-phase circuit will serve 2 patient lifts.

• Motor must not require a full PM before 3 years or 4000 lift cycles

5. Batteries

• The batteries shall be of deep discharge construction and must be non-proprietary

• System shall be capable of using batteries of same voltage and amp rating by different manufacturer without voiding the warranty.

Ceiling Lift Motor Specifications and Detail

18

6. Charger

• Charger Input: 100-240 Vac, 60 Hz.

• Charger Output: 27 Vdc, 1 A max.

7. Slings

• The straps shall be made of threaded nylon. The straps shall ensure the patient’s safety by preventing the patient from falling out of the sling.

• The sling shall be made from a polyester/nylon net material that is pliable, breathable and easy to use. The sling shall cradle the body of the patient without destruction of tissue at the contact points.

• Capable of using disposable slings or disposable covers for the slings.

• Capable of using 3rd party slings without voiding the warranty.

8. Other System Requirements

• The system shall operate in a smooth, consistent manner without any fast, slow, or jerky starts and stops.

• Emergency Lowering: Shall not require any special tools

• Capable of adding scale to system to determine patient’s weight. Capable of having an integrated scale

• The vendor shall have 24/7 telephone support staffed in the United States.

• No history of recalls.

• Disclosure of all Tort claims against vendor either pending or resolved.

9. Installation

• Install ceiling mounted patient lift system as per manufacturer’s instruction and under the supervision of manufacturer’s qualified representative.

• Contractor shall provide all labor, materials, tools, equipment, etc. required for the installation.

10. Test

• Conduct a performance test on each lift system to show that the patient lift system equipment and control devices operate properly and in accordance with design and specification requirements.

• Contractor shall provide certifications for each lift system with the room number and building including a date and time and load tested.

• Equipment certified after install. Certification shall include weight test of maximum lift capacity plus 25% at the attachment point, otherwise 100% SWL. If the system fails, contractor will make all necessary adjustments and re-test within 7 business days.

11. Warranty

• The contractor shall provide a one year warranty on all parts and labor. The warranty shall include all travel and shipping costs associated with any warranty repair. The motor shall have a three year warranty.

Ceiling Lift Motor Specifications and Detail

600 lb. motor and track (cont.)

19

Ceiling Lift Motor Specifications and Detail

750 lb. motor and track

1. Ceiling Track System

• The Ceiling Track shall be made from high strength extruded aluminum T6061-T6 at a minimum thickness of 3/16” (4.8mm)

• The Track System shall be compatible for Continuous Charge or an in line docking station

2. Lift Unit

• The Lift Unit shall be constructed of a steel frame system (2205lbs / 1000kg tested) driven by a gear reduced high torque motor

• Lift unit must be in compliance with IEC60601-1

• The Lift system shall have the following salient characteristics.

• Lifting capacity: up to 750lb using a single motor and single lifting strap

• Electronic soft-start and soft-stop motor control

• Emergency lowering device (without needing any special tool)

• Emergency stopping device

• Current limiter for circuit protection in case of overload.

• Safety device that stops the motor to lift when batteries are low.

• Lifting speed: 1.08in/s (2.75 cm/s), in full capacity

• Horizontal displacement speed: 4.7 in/s (120mm/s)- when applicable

• Emergency brake (in case of mechanical failure)

• Strap length up to 90in (2.3m) tested for 2998lbs (1360kg)

• Entire external system (track, motor, strap, hanger, etc.) shall be able to be cleaned according to infection control standards without the loss of strength and integrity of the system.

• Cab: All metal enclosure

• Handheld remote control (wired or wireless)

• Lifting strap must be made of non-porous/non-woven material for infection control cleaning precautions.

• Quick release trolley (except where curves or gates require other trolley)

• Dual controls on motor

• Digital display on motor with major data indicators scrolling consisting of cycle counter, PM counter and alert, low battery charge operation, battery level and system check

2. Spreader bar

• 6 point with spring loaded locking clips to secure sling loops

• Spreader bar must work for all lift and transfer tasks (i.e. Seated, supine, repositioning, turning, walking, hygiene and limb lifting)

4. Motors

• Vertical Movement-DC Motor

• Type: fully enclosed, permanent magnet.

• Rating: 24Vdc, 110W, 4000RPM, 0.3N-m.

• Mounting: Secured to chassis.

• Motors safe to use in wet areas (GFCI protected).

• Horizontal Movement-DC Motor when applicable

• Type: Fully enclosed, permanent magnet, integral reducer.

• Rating: 24Vdc, 62W, 260RPM, 1.0N-m.

• Mounting: Secured to chassis.

• Electrical supply will be from the junction box located in the ceiling. A dedicated 20 Amp, 120 Volt, single-phase circuit will serve 2 patient lifts.

• Motor must not require a full PM before 3 years or 4000 lift cycles

5. Batteries

• The batteries shall be of deep discharge construction and must be non-proprietary

• System shall be capable of using batteries of same voltage and amp rating by different manufacturer without voiding the warranty.

20

Ceiling Lift Motor Specifications and Detail

6. Charger

• Charger Input: 100-240 Vac, 60 Hz.

• Charger Output: 27 Vdc, 1 A max.

7. Slings

• The straps shall be made of threaded nylon. The straps shall ensure the patient’s safety by preventing the patient from falling out of the sling.

• The sling shall be made from a polyester/nylon net material that is pliable, breathable and easy to use. The sling shall cradle the body of the patient without destruction of tissue at the contact points.

• Capable of using disposable slings or disposable covers for the slings.

• Capable of using 3rd party slings without voiding the warranty.

8. Other System Requirements

• The system shall operate in a smooth, consistent manner without any fast, slow, or jerky starts and stops.

• Emergency Lowering: Shall not require any special tools

• Capable of adding scale to system to determine patient’s weight. Capable of having an integrated scale

• The vendor shall have 24/7 telephone support staffed in the United States.

• No history of recalls.

• Disclosure of all Tort claims against vendor either pending or resolved.

9. Installation

• Install ceiling mounted patient lift system as per manufacturer’s instruction and under the supervision of manufacturer’s qualified representative.

• Contractor shall provide all labor, materials, tools, equipment, etc. required for the installation.

10. Test

• Conduct a performance test on each lift system to show that the patient lift system equipment and control devices operate properly and in accordance with design and specification requirements.

• Contractor shall provide certifications for each lift system with the room number and building including a date and time and load tested.

• Equipment certified after install. Certification shall include weight test of maximum lift capacity plus 25% at the attachment point, otherwise 100% SWL. If the system fails, contractor will make all necessary adjustments and re-test within 7 business days.

11. Warranty

• The contractor shall provide a one year warranty on all parts and labor. The warranty shall include all travel and shipping costs associated with any warranty repair. The motor shall have a three year warranty.

750 lb. motor and track (cont.)

21

Ceiling Lift Motor Specifications and Detail

1,000 lb. motor and track

1. Ceiling Track System

• The Ceiling Track shall be made from high strength extruded aluminum T6061-T6 at a minimum thickness of 3/16” (4.8mm)

• The Track System shall be compatible for Continuous Charge or an in line docking station

2. Lift Unit

• The Lift Unit shall be constructed of a steel frame system (2205lbs / 1000kg tested) driven by a gear reduced high torque motor

• Lift unit must be in compliance with IEC60601-1

• The Lift system shall have the following salient characteristics.

• Lifting capacity: up to 1000lb using a single motor and single lifting strap

• Electronic soft-start and soft-stop motor control

• Emergency lowering device (without needing any special tool)

• Emergency stopping device

• Current limiter for circuit protection in case of overload.

• Safety device that stops the motor to lift when batteries are low.

• Lifting speed: 0.85in/s (2.16 cm/s), in full capacity

• Horizontal displacement speed: 4.7 in/s (120mm/s)- when applicable

• Emergency brake (in case of mechanical failure)

• Strap length up to 90in (2.3m) tested for 2998lbs (1360kg)

• Entire external system (track, motor, strap, hanger, etc.) shall be able to be cleaned according to infection control standards without the loss of strength and integrity of the system.

• Cab: All metal enclosure

• Handheld remote control (wired or wireless)

• Lifting strap must be made of non-porous/non-woven material for infection control cleaning precautions.

• Quick release trolley (except where curves or gates require other trolley)

• Dual controls on motor

• Digital display on motor with major data indicators scrolling consisting of cycle counter, PM counter and alert, low battery charge operation, battery level and system check

2. Spreader bar

• 6 point with spring loaded locking clips to secure sling loops

• Spreader bar must work for all lift and transfer tasks (i.e. Seated, supine, repositioning, turning, walking, hygiene and limb lifting)

4. Motors

• Vertical Movement-DC Motor

• Type: fully enclosed, permanent magnet.

• Rating: 24Vdc, 110W, 4000RPM, 0.3N-m.

• Mounting: Secured to chassis.

• Motors safe to use in wet areas (GFCI protected).

• Horizontal Movement-DC Motor when applicable

• Type: Fully enclosed, permanent magnet, integral reducer.

• Rating: 24Vdc, 62W, 260RPM, 1.0N-m.

• Mounting: Secured to chassis.

• Electrical supply will be from the junction box located in the ceiling. A dedicated 20 Amp, 120 Volt, single-phase circuit will serve 2 patient lifts.

• Motor must not require a full PM before 3 years or 4000 lift cycles

5. Batteries

• The batteries shall be of deep discharge construction and must be non-proprietary

• System shall be capable of using batteries of same voltage and amp rating by different manufacturer without voiding the warranty.

22

Ceiling Lift Motor Specifications and Detail

6. Charger

• Charger Input: 100-240 Vac, 60 Hz.

• Charger Output: 27 Vdc, 1 A max.

7. Slings

• The straps shall be made of threaded nylon. The straps shall ensure the patient’s safety by preventing the patient from falling out of the sling.

• The sling shall be made from a polyester/nylon net material that is pliable, breathable and easy to use. The sling shall cradle the body of the patient without destruction of tissue at the contact points.

• Capable of using disposable slings or disposable covers for the slings.

• Capable of using 3rd party slings without voiding the warranty.

8. Other System Requirements

• The system shall operate in a smooth, consistent manner without any fast, slow, or jerky starts and stops.

• Emergency Lowering: Shall not require any special tools

• Capable of adding scale to system to determine patient’s weight. Capable of having an integrated scale

• The vendor shall have 24/7 telephone support staffed in the United States.

• No history of recalls.

• Disclosure of all Tort claims against vendor either pending or resolved.

9. Installation

• Install ceiling mounted patient lift system as per manufacturer’s instruction and under the supervision of manufacturer’s qualified representative.

• Contractor shall provide all labor, materials, tools, equipment, etc. required for the installation.

10. Test

• Conduct a performance test on each lift system to show that the patient lift system equipment and control devices operate properly and in accordance with design and specification requirements.

• Contractor shall provide certifications for each lift system with the room number and building including a date and time and load tested.

• Equipment certified after install. Certification shall include weight test of maximum lift capacity plus 25% at the attachment point, otherwise 100% SWL. If the system fails, contractor will make all necessary adjustments and re-test within 7 business days.

11. Warranty

• The contractor shall provide a one year warranty on all parts and labor. The warranty shall include all travel and shipping costs associated with any warranty repair. The motor shall have a three year warranty.

1,000 lb. motor and track (cont.)

23

Ceiling Lift Motor Specifications and Detail

Schedule “A” Spanning and Cantilever Specifications

SCHEDULE "A" Spanning & Cantilever Specifications

Single Track T6010

Single Track with Continuous

Charge T6015

Single Track G2

Standard Gantry Crosser

T6010G1

Heavy Duty Gantry Crosser

T6010G3

Double Track T6010D2

LIFT LOAD (lbs) L L L L300 136 135 208 282450 115 115 178 245600 102 101 158 219750 92 92 144 200

1000 80 80 126 176Design limits based on 2010 Aluminum Design Manual published by The Aluminum Association

Item Clarification Points1 Supports must be equally spaced between each other2 Fluorescent light jumps may have only 2 long brackets in the 2 ft section of track3 Maximum allowable cantilever for the Ceiling Mounted Track T6010, T6015 and T6010G1 is 6 inches from last support4 Maximum allowable cantilever for the Ceiling Mounted Track T6010G3 and T6010D2 is 12 inches from last support5 Standard Gantry Crosser T6010G1 and Heavy Duty Gantry Crosser T6010G3 may be used as a Ceiling Mounted Track 6 For all Unistrut and Anchors on the structural drawings refer to manufactures specifications for proper allowable loads

Allowed MAXIMUM Spans Listed Are within and Conform to the ISO 10535 Deflection Limit of L/200 max

60

Spacing - center line to center line of Supports (inches)

104

Ceiling Mounted Track or Gantry Crosser

L

877769

24

Ceiling Lift Motor Specifications and DetailElectrical Wiring Information for Docking Style Charging System

Electrical Wiring Information for Continuous-Charge Charging System

25

Ceiling Lift Motor Specifications and Detail

Anchoring Detail for Concrete Structure Suspended Mounting

26

Ceiling Lift Motor Specifications and Detail

Anchoring Detail for Concrete Structure Suspended Mounting

27

Ceiling Lift Motor Specifications and Detail

Anchoring Detail for Unistrut Bridge Below Steel Pan Deck

28

ceiling lifts

• Electric fixed ceiling lift available in 400, 600 or 750 lb capacity

• Manual or power transverse options• 6-point spreader bar for enhanced patient

comfort with locking clips• Can be used with exclusive “Curtain Track

Solution”• Smart sleep mode function to conserve

battery power• Low-profile Cirrus accommodates 8ft ceilings

CIRRUS LIFT SERIES

• Electric fixed ceiling lift with 1,000 lb capacity to safely and effectively reposition bariatric patients

• Manual or power transverse options• Oversize spreader bar for superior bariatric

comfort• Can be used with exclusive “Curtain Track

Solution”• Visual and audible low battery indicators

PINNACLE LIFT SERIES

• Portable ceiling lift available in 450 and 600lb capacity can easily be moved from room to room

• 6-point spreader bar for enhanced patient comfort

• Long travel height enables lifting patient from floor

• Optional cart for relocation• Optional infection control strap available

STRATUS LIFT SERIES

slings & accessories

• Up to 1,000 lb capacity• Combi, long seat, hygiene, harness and• repositioning models with full range of sizes• Durable, washable material in solid fabric or

mesh for bathing• Most slings available in disposable• Color-coded with serial number for

identification• 6 straps to accommodate 6-point spreader

bar for enhanced patient comfort and security• Replacement slings for all types of lifts and

manufacturers

FAbRIC SLINGS

• 2-Point Spreader• 6-Point 750 lb Spreader• 6-Point 1,000 lb Spreader

• Patent pending — the only true infection control strap available

• Easy wipe-down with hospital-grade hard surface cleaner protects against MRSA, C. Diff and H1N1

• Available on Cirrus, Cirrus LP, Pinnacle and Stratus ceiling lifts

ExCLUSIVE INFECTION CONTROL STRAP

Tollos® Product Range

SPREADER bAR OPTIONS

29

mobile lifts

• Mobile floor lift available in 600 or 750 lb capacity

• Extra long boom eliminates patient contact with the lift

• Standard 6-point spreader bar for superior sling adjustability

• Extra-low base option allows access beneath all low beds

• Optional integrated digital scale provides 6” of extra height vs. external scale

ULTRALIFT 3000 & 3510xH

• Dual mast mobile floor lift with 475 lb capacity (highest in its class)

• Superior lifting range from 77” to 10”

• Flexible options including 6-point spreader bar, external or integrated scale, and powered base widening

ULTRALIFT 2000

• Sit-to-stand lift available in 350, 450 and 750 lb capacity

• All electric with powered base widening

• Removable foot plate for ambulation

• “Gel Foam” head protector and kneepad for patient safety

• Optional integrated digital scale

STEADY AID SERIES

• Early recovery assisted standing/relocating device with 400 lb capacity

• Removable footplate for ambulation

• Padded seat with adjustable angle for maximum comfort

• Optional oxygen tank holder

ULTRA MOVE

• Mobile floor lift with 1,000 lb capacity

• Oversize 6-point spreader bar ensures patient comfort

• Powered base widening• Safely transfer bariatric patients

from the floor• Optional integrated digital scale

TITAN-x

• Designed specifically for simple, safe transfer from vehicle

• 500 lb capacity• Small footprint for maximum

maneuverability• Powered base widening• Lifetime frame warranty

VEHICLE ExTRACTOR

Smarter Is Safer - and More Cost-Effective

Many Tollos lifts include our innovative iQ Technology™ and software. Combining proprietary electronics and an optional integrated scale, iQ Technology automates the tracking of critical safe patient handling data for training, compliance and equipment diagnostics.Maintenance features include a constant alert after 1,000 lifts and failsafe shutdown after 6,000 cycles.

Look for the iQ to find lifts equipped with this valuable, time-saving Tollos innovation.

Tollos® Product Range

• Available options for the 3000 series Ultralift include:

• Internal scale with IQ technology• External Scale• External battery• Flat base legs for low-clearance

ULTRALIFT OPTIONS

30

lateral transfer

• Reusable and single-patient use sheets and tubes

• Multi-directional slide tubes are a single, silicon tubular sheet designed to safely move the patient during transfer, in-bed repositioning, lateral transfer, pivoting and rolling

• Multi-directional slide sheets are a two-sheet set to reduce friction during lateral transfer and repositioning

• Proven slipperiness after 250 washes; single-patient use can last up to 4 months, reducing costs

SALLYSLIDES®

• Prevent costly injuries• Unique ergonomic handle design adjusts

to a wide range of user heights• Universal compatibility:

• Linen carts and trolleys• Equipment cart• Trash bins

LINEN/EQUIPMENT CART TUG

• Prevent costly injuries• Increase delivery time and patient

satisfaction by reducing wait for transport• Reduce operating costs through reduced

transport headcount• Universal compatibility

STAMINALIFT 5000 bED MOVER

transport solutions

Tollos® Product Range

• The Rise and Go is one of the most progressive electric gate training walkers available

• Light weight aluminum construction• 330 lb weight capacity• Will assist patient/resident to standing• Adjustable base• Removable foot plate• Dual position adjustable shin pad• Electric Rise• Comfortable positioning system

bURE RISE & GO

• This simple pulley system provides a 3/1 mechanical advantage for quick and easy adjustment of body-weight support.

• Unique “cam-cleat” allows for a secure hold but can be released and adjusted when needed with a simple flick of the wrist.

• The system is extremely light weight which allows for rapid and dynamic changes in direction that cannot be performed with heavier electric lifts.

HEIGHT ADJUSTMENT SYSTEM

early mobilization

• Prevent costly injuries• Available in multiple cylinder count

configurations• Features center wheel drive system that

provides tight turning radius in cramped quarters

• foam filled never flat tires• Solid state regenerative braking

MOTORIzED MEDICAL GAS CART

31

hygiene solutions

Tollos® Product Range

• Tilting allows water savings by only requiring 24 gallons to fill

• Unique tilting allows reclining position to fully immerse patients who have challenging conditions

• 3 plumbing configurations from which to choose (side, front, or island)

• Optional Auto-fill feature available

• Magnetic pads for easy infection control• Multi positioning/locking arms• Super comfortable seating• 350lb/159kg capacity• Reclines to 35 degrees• Magnetic seat attachment for easy

cleaning• Tollos durability yet

extremely cost effective

• Designed specifically for use with the RL9 Victoria Bath Lift, which provides seamless transfers from bed to bath

• The low threshold and wide side-entry door allows easy access for residents with various degrees of mobility

• The wide built-in contoured seat allows the larger resident to sit comfortably and safely

• 600 lb weight capacity

• Designed to bathe highly dependent residents with challenging conditions in a comfortable supine position

• Height adjustable or fixed height• Compatible with a wide range of transport

and lifting devices• Optional Auto-fill feature available

RR7-II ATLANTIC RECLINING TUb

RG9 VICTORIA SIDE ENTRY TUb LEVOLO ELECTRIC SHOWER CHAIR

RS8 GENEVA SUPINE TUb

RL9 bATHING SYSTEM LIFT

DISINFECTION CAbINET

• Designed specifically for use with the RG9 Victoria tub.

• Safely and seamlessly transfer patients from bed to bath in a comfortable position

• Heavy duty steel powder coated frame• Unique combination of style, ease of use,

comfort, and low cost of ownership

• Simplify disinfection and greatly reduce possibility of cross-contamination in your bathing area

• Wall-mounted system allowing efficient use of bathing area space

• Unique mixing valve uses exact dilution ratio of disinfectant solution for optimal performance.

• Cabinet is lockable providing a secure place for disinfectants and cleaning supplies

32

Tollos® Product Range

hygie® fluid management solutions

Hygie’s Hy21® technology helps to effectively manage and contain bodily wastes at point of care; it also ensures that health care providers adopt the best method to reduce the number of steps required in handling bedpans, thereby reducing the spread of pathogens which may lead to contamination and HAIs.

Used with the Hygienic Covers®, our supports are the perfect solution to contain potentially harmful pathogens, and further promote safe and reliable practice in health care.

The unique super-absorbent pad included in each Hygienic Cover® is designed to turn up to 500ml of liquid wastes into agel within seconds. It helps to reduce the risks of splashes, spills and germ dispersal wich contribute to the prevention of healthcare-associated Infections, cross-contamination, etc.).

After using the Hygienic Cover®, close it securely and discard it in the designated area.

The single-use product offers inscreased hygiene level, blocks odors, and is time-saving. It is easy to discard without risk.

• Makes collection and transportation safer.

• Reduces the risks of splashing and spilling.

• Blocks odor spreading.

• Reduces cleaning tasks.

• Limits the spread of harmful bacteria.

33

34

Tollos® Product Range

is height-adjustable and ideal for bathrooms used by multiple users with individual needs. It may be in hospitals and nursing homes, but also in private homes.

ROPOx™ SUPPORT WASHbASIN

ropox™ bathroom solutions

ROPOx™ FOLDING SHOWER SEATis ideal for bathrooms where support is needed during bathing and where space is restricted. The shape ensures secure and pleasant showering.

Ropox™ bathroom products offer flexible bathroom solutions to compensate for reduced physical ability. Products are ergonomical, strong and provide extra support during washing. toileting and bathing.

The main goal of the Ropox™ product line is:

• To help people with reduced physical ability to be more independent and to improve everyday life and self-esteem.

• To minimize patient falls through (a) sinks that either move to the patient to enable the patient to sit and wash or has integrated handles, (b) super versatile grab bars, and (c) wall-mounted shower chairs.

• To provide enhanced aesthetics while addressing smaller spaces with space efficient products.

ROPOx™ TOILET SUPPORT ARMS

The arms may be folded up to any angle making them more convenient to pull down. With 90 mm. differential, the toilet support arms are extremely useful when standing up and transferring.

ROPOx™ SWINGING WASHbASIN

The shape and size of the Ropox™ Swing Washbasin ensures that seated and standing users can use the basin from the front or sides. A model of the washbasin can also be height adjusted to suit individual users.

Tollos® Product Range

ropox™ bathroom solutions

35

Featured Products Include•Swinging Washbasin•Toilet Support Arms•Bathroom Grab Bars•Folding Shower Seat•Support Handle Washbasin•Shower and Changing Bed

U.S. Corporate Office

1 Easter Court, Suite J

Owings Mills, MD 21117

410.363.1515 PHONE

888.363.7224 TOLL FREE

Canadian Office

75 Dyment Road

Barrie Ontario L4N 3H6

705.733.0022 PHONE

888.363.7224 TOLL FREE

www.tollos.com

Formerly T.H.E. Medical