tools and supplies required
TRANSCRIPT
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2012 American Honda Motor Co., Inc. – All Rights Re
AII 13052
CARGO NETP/N 08L96-TR0-100
served. AII 47335 (1211
2013 CIVIC2 AND 4-DOOR
) 0
Issue Date
NOV 2012
PARTS LISTCargo net
2 Anchors A
4 Self-tapping screws
4 Anchors B
2 Bolts
2 Rivet nuts
Template R
Template L
Accessory User’s Information Manual
TOOLS AND SUPPLIES REQUIRED
Rivet Nut Tool, 6 mm (T/N 07AAE-000A100)Open end wrenchPushpinFelt-tip penDrill3 mm, 5.5 mm, and 9 mm Drill bitsPlastic Trim Tool (T/N SILTRIMTL10)Eye protection (face shield, safety goggles, etc.)Touch-up paintFileHex wrenchTapePliersShop towelRuler
INSTALLATION
NOTE: Be careful not to damage the body.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1 of 68L96-TR0-1000-90
1. Install a bolt into each anchor A, and install a self-tapping screw into each anchor B.
2. Open the trunk lid. Remove the four clips from the trunk side lining.
Q071518AJ
4 ANCHORS B
4 SELF-TAPPING SCREWS
2 BOLTS
2 ANCHORS A
Q071501CJ
TRUNK SIDE LINING
CLIPS (Reuse.)
CLIPS (Discard.)
2 of 6 AII 47335
3. While wearing eye protection, enlarge the two clip holes shown to 9 mm. Remove any burrs, and apply touch-up paint to each hole. To prevent drilling through the inner panel, wrap tape around the drill bit 10 mm (0.4 in.) away from the tip.
Installing the Rivet Nuts
4. Pull off the weatherstrip in the areas shown, and move the trunk side lining out of your way.
Q071502BJ
TRUNK SIDE PANEL
TRUNK SIDE LINING
DRILL
DRILL BIT(9 mm)
HOLE
HOLE
TAPE
DRILL BIT(9 mm)
10 mm (0.4 in.)
Q0D2001AJ
WEATHERSTRIP
TRUNK SIDE LINING
(1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
5. Install two rivet nuts in the 9 mm holes you enlarged, as described in the following steps.
6. Screw the rivet nut onto the mandrel of the tool as shown.
7. Insert the rivet nut into the hole in the trunk side panel, and insert the hex wrench into the tool.
8. While holding the tool with the hex wrench, turn the open end wrench clockwise to install the rivet nut to the trunk side panel.
9. Remove the tool from the rivet nut by turning the hex wrench counterclockwise.
10. Reinstall the trunk side linings and the weatherstrip.11. Reinstall the two clips removed in step 2.
Q071503CJ
9 mm HOLE(Enlarged in step 3.)
2 RIVET NUTS
9 mm HOLE(Enlarged in step 3.)
RIVET NUT
RIVET NUT
TRUNK SIDE PANEL
RIVET NUT TOOL
MANDREL
OPEN END WRENCH
HEX WRENCH
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47335
12. Install two bolts/anchors A into the rivet nuts.
13. Pull the levers to fold the rear seat-back forward.
Q071507CJ ANCHOR A
TRUNK SIDE LINING
TRUNK SIDE PANEL
2 RIVET NUTS(Installed in step 5.)
BOLT
BOLTS/ANCHORS A
RIVET NUT
Q071508AJ
LEVER
REAR SEAT-
LEVER
(1211) 3 of 6
14. Remove the trunk floor mat (one clip).
15. Attach template R to the trunk right side lining as shown.
Q071509BJ
TRUNK FLOOR MAT
CLIP
Q071510CJ
VEHICLE CLIP (Align.)
TEMPLATE R
TRUNK RIGHT SIDE LINING TAPE
MARKS
4 of 6 AII 47335
16. Put pieces of tape underneath the two marks on template R as shown.
17. Mark the tape under template R with a pushpin and a felt-tip pen as shown.
18. Remove template R.19. Attach template L to the trunk left side lining as
shown.
Q071511BJ
TEMPLATE R
FELT-TIP PEN
PUSHPIN
Q071512CJ
TEMPLATE L
TRUNK LEFT SIDE LINING
VEHICLE CLIP (Align.)
TAPE
MARKS
(1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.
20. Put pieces of tape underneath the two marks on template L as shown.
21. Mark the tape under template L with a pushpin and a felt-tip pen as shown.
22. Remove template L.23. While wearing eye protection, drill a 5.5 mm hole
through the trunk side lining and the trunk floor at each mark. Start with a 3 mm drill bit and finish with a 5.5 mm drill bit. Remove any burrs, and apply touch-up paint to each hole.• To prevent drilling through the inner panel, wrap
a tape around each drill bit 10 mm (0.4 in.) away from the tip.
• Before drilling, pull up the trunk side lining and check that the trunk lid opener cable is not under the places to be drilled.
Q071513BJ
TEMPLATE L
FELT-TIP PEN
PUSHPIN
Q071514CJ
10 mm(0.4 in.)
MARKS
DRILL3 mm 5.5 mm DRILL BITSTAPE
© 2012 American Honda Motor Co., Inc. – All Rights Reserved. AII 47335
24. Repeat step 23 to drill the left side of the vehicle.25. Remove the pieces of tape. Install self-tapping
screws/anchors B into each 5.5 mm hole you made.
NOTE: If tightening becomes difficult, protect the self-tapping screw/anchor B with a shop towel, and tighten it with pliers.
26. Repeat step 25 to install two self-tapping screws/anchors B on the left side of the vehicle.
Q071515CJ HOLES
SELF-TAPPING SCREW/ANCHOR B
SELF-TAPPING SCREW/ANCHOR B
SHOP TOWEL
PLIERS
(1211) 5 of 6
27. Install the cargo net to the anchors in the trunk. The cargo net can be installed in two different positions.
Position #1: Vertical divider / pouch:
Position #2: Flat floor cargo:
NOTE:• Do not store large or fragile objects in the net.• Do not store objects with sharp edges or corners, as
they may damage the cargo net or the vehicle. Wrap them in paper or a blanket so they will not contact the net directly.
Q071516AJ
ANCHOR A
ANCHOR B
CARGO NET
Q071517AJ
ANCHOR B
ANCHOR B
6 of 6 AII 47335
(1211) © 2012 American Honda Motor Co., Inc. – All Rights Reserved.