toshiba camileo

8/13/2019 Toshiba Camileo

1/75

Users ManualCamileo SX900

CZ

DE

DK

ESFI

FR

GR

HR

HU

IT

NLNO

PL

PT

RS

RU

SE

SKSL

TR

AR


2/75

EN i Users Manual

INTRODUCTIONWelcome and thank you for choosing a TOSHIBA product.For your convenience, your TOSHIBA product is furnished with two guides:

a) Quick Start Guide, andb) this comprehensive PDF Users Manual.Please read these instructions carefully before using the camcorder. Keepthis Manual in a safe place for later reference.

Symbols used in this manualHINT Points giving some extended instructions or special points to pay

attention to.

CAUTION Points that require special attention.(page xx) Refer to the page indicated for detailed information.


3/75

Users Manual ii EN

SHOOT, PLAY BACK AND SAVE

Preparing the camcorder

1 Insert the battery pack.

2Open

3Insert the battery pack.

4Close the battery cover.

Battery cover

1 Push out


4/75

EN iii Users Manual

About the battery packYou will find the battery pack inserted in the camcorder. When shipped fromthe factory, the battery pack is inserted backwards to prevent current flow.Before using, please re-insert the battery pack correctly as shown in theillustration.


5/75

Users Manual iv EN

2 Insert the SD Memory Card.h An SD Memory Card is not included with your camcorder. Please

purchase a commercially sold card.h In this manual, the SD Memory Card is referred to as the card.

1Open the card slot cover. 2Insert the card.

3Close the card slot cover.

2Pull it out.

1Push the card in.


6/75

EN v Users Manual

Shooting

1 Press the POWER button for atleast 1 second to turn the

camcorder on.h If the screen to set the date

and time appears, press theMENU button 2 times tocancel it.For how to set the date andtime, see page 19.

2 Record.To record a video clip:h Press the [ ] button to

begin recording a video clip.h Press the [ ] button again

to end the recording.To take a photo:h Press the [ ] button.h A still image is captured.

3M-S15 000:00:17

Full-HD

[ ] button

(Video recording button)

[ ] button(Photo shooting button)

POWER button


7/75

Users Manual vi EN

Playback

1 Press the play [=] button.h The display changes to the

Playback Screen.

2 Select the image to play back.h Use the arrow keys to move

the orange frame to the imageyou wish to play back.

h The image information for theframed image is shown in the

bottom part of the monitor.

3 Press the OK button.h Press the play [=] button.

Deleting files

1 On the screen in step 2, movethe orange frame to the file youwish to delete, and press theMENU button.

2 Select DELETE, and pressthe OK button.

3 Select DELETE SINGLE, andpress the OK button.

4 Select DELETE, and pressthe OK button.h If you press [G] or [H], the

screen to delete a different file

will appear.

2010.12.24 18:41 100-0006

6.5MB 00:00:05Full-HDSD

OKOK

MENU button

Remaining batterypower indication

Orange frame

Play [=] button

Arrow keys

Arrow keysOK button


8/75

EN vii Users Manual

5 When you are finished deleting files, press the MENU button.h Pressing the MENU button 3 times will return you to the screen in step

2.

When you are finished using the camcorder...Press the POWERbutton for at least 1 second to turn the camcorder off.


9/75

Users Manual viii EN

Copy data from your camcorder to thecomputer

Connect your camcorder to a computer, and copy the desired data to thecomputer.

1 Turn on the computer, and use the supplied dedicated USB interfacecable to connect your camcorder to the computer.h Connect the cable between the camcorders USB/AV terminal and the

computers USB connector.

2 Turn on the camcorder (page 16).h The USB Connection Screen appears on the camcorders monitor.

USB CONNECTION

COMPUTER

PRINTER

CANCEL

OKCANCEL OK

To USB/AV terminalSupplied dedicatedUSB interface cable

To USB connector


10/75

EN ix Users Manual

3 Select COMPUTER, and press the OK button.h The screen to select the

computer connection modeappears.

4 Select CARD READER, and press the OK button.

5 Copy data from your camcorder to a computer.

Dismounting the camcorder

CAUTIONi To disconnect your camcorder, be sure to follow the procedure below.

Failure to follow this procedure may cause faulty operation of yourcomputer or corrupt the files in your camcorder.

1 Left-click on the icon for safely removing hardware in the task tray.h A list appears showing the devices connected to the computers USB

connector.

2 Left-click on the camcorder drive (E:).h The camcorder can now be disconnected.h The drive name (E:) may be different on your computer.

HINTAbout the application softwareConcerning the application software, the following software is bundled in thesupplied DVD-ROM.iArcSoft MediaImpression 2

Watch movies and organize files.With application installed, when your camcorder is connected to yourcomputer in the YouTube mode, the camcorder is ready to upload to

YouTube.iMAGIX Movie Edit Pro 15 Plus Trial

For editing movies. 30-day trial version.

OK

USB CONNECTION

CARD READERYou Tube

MTPCANCEL

OK


11/75


12/75

EN 1 Users Manual

CONTENTSINTRODUCTION .................................................................................... iCHECKING THE INCLUDED ACCESSORIES ...................................... 3

About the power plug ...................................................................... 5SAFETY INSTRUCTIONS ..................................................................... 6ABOUT THE CARD ............................................................................... 7

Media cards that can be used with this camcorder ......................... 7What card means in this manual .................................................. 7

SETUPPARTS NAMES ..................................................................................... 8INSTALLING THE CARD ..................................................................... 10

CHARGING THE BATTERY PACK ..................................................... 12About recharging .......................................................................... 15About the temperature alert icon \ .......................................... 15

TURNING THE CAMCORDER ON AND OFF ..................................... 16Turning on the camcorder ............................................................. 16Turning off the camcorder ............................................................. 16Turning on the camcorder when the power save (sleep)mode is active ............................................................................... 17

DATE AND TIME SETTING ................................................................. 19

SWITCHING BETWEEN THE RECORDING MODE ANDPLAYBACK MODE .......................................................................... 22

ACCESSING THE MENU SCREEN .................................................... 23

SHOOTINGVIDEO CLIP RECORDING .................................................................. 26SHOOTING SINGLE SHOTS .............................................................. 27SHOOT A STILL IMAGE WHILE RECORDING A VIDEO CLIP .......... 29MACRO-PHOTOGRAPHY (ZOOM) .................................................... 31

PLAYBACKPLAYING BACK VIDEO CLIPS AND STILL IMAGES ......................... 32

How to save one frame from a video clip as a still image ............. 34


13/75

Users Manual 2 EN

CONNECTING TO A TVCONNECTING TO A TV .......................................................................35

Connecting to a video input terminal .............................................36Connecting to the HDMI terminal ..................................................36

PLAYING BACK ON A TV ....................................................................37

APPENDICESFREQUENTLY ASKED QUESTIONS ..................................................38OVERVIEW OF THE MENU SCREEN .................................................44

Recording Menu ............................................................................44Playback Menu ..............................................................................50Option Menu ..................................................................................52

SPECIFICATIONS ................................................................................56Camcorder .....................................................................................56

Concerning the multi-indicator .......................................................57Others ............................................................................................58

TOSHIBA SUPPORT ............................................................................59REGULATORY INFORMATION ...........................................................60ADDITIONAL INFORMATION ..............................................................63


14/75

EN 3 Users Manual

CHECKING THE INCLUDED ACCESSORIES

Soft case: 1 Software DVD + UsersManual (DVD-ROM): 1

Li-ion battery pack: 1 AC adaptor and power plugs(page 13): 1

Dedicated USB interfacecable(page viii): 1

Dedicated AV interface cable(page 36): 1

Mini HDMI Cable: 1 Handstrap: 1


15/75

Users Manual 4 EN

Lens cap: 1 Quick Start Guide

Warranty Leaflet


16/75

EN 5 Users Manual

About the power plugA power plug suitable for the destination country is provided for the ACadaptor.

CAUTIONDo not use other AC/DC adaptors than the one bundled with yourdevice, as otherwise your device may be damaged.

k How to attach


17/75

Users Manual 6 EN

SAFETY INSTRUCTIONS1. Do not drop, puncture or disassemble the camcorder; otherwise the

warranty will be voided.

2. Avoid all contact with water, and dry hands before using.3. Do not expose the camcorder to high temperature or leave it in direct

sunlight. Doing so may damage the camcorder.4. Use the camcorder with care. Avoid pressing hard on the camcorder

body.5. For your own safety, avoid using the camcorder when there is a storm or

lighting.6. Do not use batteries of different specifications. Doing so may lead to the

potential for serious damage.

7. Remove the battery during long periods between usages, as adeteriorated battery may affect the functionality of the camcorder.8. Remove the battery if it shows signs of leaking or distortion.9. Use only the accessories supplied by the manufacturer.10. Keep the camcorder out of the reach of infants.CAUTION11. Risk of explosion if battery is replaced by an incorrect type.12. Dispose of used batteries according to the instructions.


18/75

EN 7 Users Manual

ABOUT THE CARD

Media cards that can be used with thiscamcorder

The type of card that can be inserted into and used with this camcorder is:iSD Memory CardiSDHC Memory CardiSDXC Memory Card

What card means in this manuali In this manual, SD Memory Cards, SDHC Memory Cards and SDXC

Memory Cards that can be used in this camcorder are referred to as

card.


19/75

Users Manual 8 EN

SETUP

SETUPSETUP

PARTS NAMES

Front

LensMonitor unit

* The tripod mounting hole ison the bottom.

Speaker

LED light unit

Stereo microphone


20/75

EN 9 Users Manual

Rear

DC IN terminal

MENU button

Monitor

OK button

Play [=] button

Card slot cover

Zoom switch

Arrow keys

[ ] buttonPhoto shootingbutton

[ ] buttonVideo recordingbutton

POWER button

Arrow keys

Strap holder

Multi-indicator

Battery cover


21/75

Users Manual 10 EN

SETUP

INSTALLING THE CARDBe sure to format a newly purchased card or one that was used in anotherdevice before using it in your camcorder(page 11). If an unformatted card is

used, the card itself may become unusable.Your camcorder has an internal memory, so you can record without a cardinstalled.

1Open the card slot cover. 2Insert the card.

3Close the card slot cover.

2Pull it out.

1Push the card in.


22/75

EN 11 Users Manual

CAUTIONDo not attempt to forcibly remove the cardiDoing so may damage the card or the stored files.If the multi-indicator is flashing orange...iNever remove the card when the multi-indicator is flashing orange, as

doing so may result in loss of files stored in the card.

HINTTo format a card1 Insert the card in the camcorder, and press the POWER button (pages 10

and 16).2 Set the camcorder to the NORMAL mode.3 Press the MENU button.

4 Select the [E

] tab, and press the OK button.5 Select FORMAT and press the OK button.i The Format Screen appears. Follow the instructions on the screen to

format the card.Shooting without a card installediWhen a card is installed, images are recorded to and played back from the

card. When no card is installed, images are recorded to and played backfrom the camcorders internal memory. When the camcorder is turned onwith no card installed, the internal memory icon is shown on the monitorto let you know that the images you capture will be saved to thecamcorders internal memory.


23/75

Users Manual 12 EN

SETUP

CHARGING THE BATTERY PACKPlease charge the supplied battery pack before using it. Install the batterypack in the camcorder, and connect the AC adaptor to charge the battery.

Power to the camcorder can also be supplied from a power outlet when theAC adaptor is connected.

1 Open the battery cover..

2 Insert the battery pack, then replace the battery cover.

2Open

Battery cover

1 Push out

3 Insert the battery pack. 4Close the battery cover.


24/75

EN 13 Users Manual

3 Connect the AC adaptor to the camcorder.h Charging begins.

h During charging, the multi-indicator is lit orange. When charging is

completed, the indicator turns off.h The multi-indicator flashes orange if the battery pack is defective or is

not installed correctly. Make sure that the battery pack is correctlyinstalled.

h The charging time is approx. 120 minutes.

To power outlet

5Connect the AC adaptor.h

Charging begins.


25/75

Users Manual 14 EN

SETUP

CAUTIONDo not charge the battery pack immediately after the camcorder hasbeen in continuous use for a long timei The battery pack becomes hot when the camcorder is used continuously

for a long time. If you attempt to charge the battery pack in this state, the

multi-indicator may flash orange and it may not be possible to charge thebattery pack. Wait until the battery pack has cooled down beforeattempting to charge it.

Does the battery pack appear swollen?i The lithium-ion battery used in this camcorder may expand slightly when

stored in a hot environment or repeatedly used, but this is not a safetyhazard. However, a battery that is difficult to insert because it has becomeswollen may then be impossible to extract from the battery compartment.In this case, please discontinue its use and replace it with a new battery.

Do not use the battery with the outer covering or label removediDoing so may result in malfunction.

HINTAbout the internal backup batteryi This camcorders internal battery serves to maintain the date and time

settings, as well as the shooting settings. The backup battery will be fullycharged when the battery pack is kept in the camcorder continuously forabout 2 days. In the fully charged state, the backup battery will maintain

the camcorder settings for about 7 days.When not using the camcorder for a long time, remove the battery packiA small amount of power is still used even if the camcorder is turned off,

and it is therefore recommended that the battery pack be removed fromthe camcorder if it is not going to be used for a long time. Note that whenthe battery pack is removed for a long period, the time and date settingsmay be cleared. Before using your camcorder again, be sure to confirmthat the camcorder settings are correct.

Recharging when connected to the USB terminali The battery can be recharged while the camcorder is connected to a

computer.iNote, however, that the time it takes to recharge will differ depending on

the camcorders operating condition.iConnect the dedicated USB interface cable to the USB connector on your

computer. Do not connect it to the USB connector on the monitor or thekeyboard, or to the USB hub.

i If the camcorder is not going to be used for an extended period of time,please disconnect the dedicated USB interface cable from the camcorder.


26/75

EN 15 Users Manual

About rechargingRecharging takes place only when the camcorder is turned off, or when thepower save function or the sleep function has been activated. Rechargingdoes not take place when the camcorder is in the recording mode or playback

mode.

About the temperature alert icon \During camcorder use, if the temperature of the battery or inside thecamcorder (excluding the battery) rises, a temperature alert icon \willappear as described below.

k When the battery or internal camcorder (excluding battery)temperature rises during useh During camcorder use, if the temperature of the battery or inside the

camcorder (excluding the battery) rises, a \icon lights on themonitor. It is still possible to record and play back even when the \icon is lit; however it is advised that you discontinue use as soon aspossible and turn the camcorder off.

h If the temperature rises further, the \icon will start to flash, and thecamcorder will turn off automatically.The camcorder cannot be turned on until the temperature has dropped(or as long as the \icon remains flashing). Please wait until the

temperature has dropped before resuming use.h During video recording, a countdown indicator will show the time

starting about 15 seconds before shutdown. When the indicator shows0 seconds, recording stops.

h If the camcorder is turned off while the temperature is high (that is, whilethe \icon is flashing), it cannot be turned on again until thetemperature has dropped (or as long as the \icon remains flashing).


27/75

Users Manual 16 EN

SETUP

TURNING THE CAMCORDER ONAND OFF

Turning on the camcorder

1 Open the monitor unit, and pressthe POWER button for at least1 second.h If you briefly press the POWER

button, once, the camcorder willswitch to the power save mode.

Turning off the camcorder

1 Press the POWER button for at least 1 second.h The camcorder turns off.

POWER button

Monitor unit


28/75

EN 17 Users Manual

Turning on the camcorder when the powersave (sleep) mode is active

In order to preserve battery pack power, the power save (sleep) function willautomatically turn off the camcorder after about 1 minute of no use during

shooting, or about 5 minutes of no use during playback (factory-presetsetting).

iWhen the power save mode is active, you can restore the power by any ofthe following methods: Press the POWER button. Press the [ ] button. Open the monitor unit.

iAfter the power save mode has been active for about 1 hour, the

camcorder will switch to the standby mode. In this case, you can restorethe power by pressing the POWER button, or by closing and then openingthe monitor unit.

iWhen the AC adaptor is connected, the power save mode will becomeactive about 5 minutes after the camcorder is turned on (factory-presetsetting).

iWhen the camcorder is connected to a computer or printer, the power savemode becomes active after about 12 hours.


29/75

Users Manual 18 EN

SETUP

HINTTo immediately activate the power save modeiPress the POWER button briefly to activate the power save function.About the standby modei To turn off the camcorder only briefly, you can close the monitor unit to put

the camcorder in the standby mode. The standby mode uses almost nopower. When the monitor unit is opened again, the camcorder turns onimmediately and you are ready to shoot or view images without any delay.

CAUTIONIf theKicon appears...iWhen a picture is taken, the date and time it was captured are recorded

with it. If the date and time settings have not been completed(page 19),the date and time cannot be recorded with the captured images. For thisreason, immediately after the camcorder is turned on, the Set date andtime reminder briefly appears, after which theKicon is shown on theRecording Screen. To have the date and time recorded with the images,please complete this setting before capturing images.

iDue to the characteristics of the camcorder, the outer surface maybecome warm during use, but this does not indicate a malfunction.

i If the camcorder starts to feel uncomfortably hot during use, you

might temporarily discontinue use until it cools down, or try holding itin your other hand for a while.Please use a tripod or other support when using the camcorder for along time.


30/75

EN 19 Users Manual

DATE AND TIME SETTINGThe camcorder will record the date and time an image or audio recording istaken so that you can display them during playback. Therefore, before

capturing images, make sure the correct date and time are set.h To correct the date and time setting, please see under HINTon page 21.

Example: To set the clock to 7:30 p.m. on December 24, 2010

1 Turn on the camcorder(page 16),and press the OK button.h The Clock Set Screen appears.h Follow the procedures below to

enable or disable the datedisplay during playback, to setthe display format for the date,and to set the date and time.

h To display the Recording orPlayback Screen, press theMENU button 2 times.

2 Set the date.1 Select DATE.2 Press the OK button.h The Set Date Screen

appears.3 Set the date to 2010/12/24.h The date is set in the

following order: Set the yearSet the month Set theday.

h Press [G] or [H] to selectyear, month or day. Press [I]or [J] to increase or decreasethe number.

4 Press the OK button.

CLOCK SET

DATE

TIME

DISP

OK

2010/02/01

00:00

D / M / Y

OK

OK

CLOCK SET

DATE 2010/12/24

OK


31/75

Users Manual 20 EN

SETUP

3 Set the clock.1 Select TIME.2 Press the OK button.h The Set Time Screen

appears.3 Set the time to 19:30.h The time is set in the

following order: Set the hourSet the minute.

h A 24-hour clock is used forthe time display.

4 Press the OK button.

4 Set the order in which the date isdisplayed during playback.1 Select DISP.2 Press the OK button.h The Set Date Format Screen

appears.3 Press [I] or [J].h Press [I] to change the

displayed date order as

follows:

Press [J] to change it in the reverse order.4 Press the OK button.

5 Press the MENU button.h The date and time setting is completed.h To display the Recording or Playback Screen, press the MENU

button.

OK

19:30TIME

CLOCK SET

OK

OK

CLOCK SET

OK

DISP D / M / Y

D / M / Y Y / M / D M / D / Y


32/75

EN 21 Users Manual

HINTiUnder normal conditions, while the battery pack is being replaced, an

internal battery will maintain the date and time settings. However, there is asmall chance the settings may be lost (the backup will last for about7 days). It is recommended to check that the date and time settings are still

correct after replacing the battery pack and before shooting or recording ofany type (follow step 1).

To correct the date and time settings1 Turn on the camcorder.2 Display the Option Setting Menu 1(page 24).3 Select CLOCK SET and press the OK button.h The screen to set the date and time appears.h The current date and time settings are shown.

4 Select the line you wish to change, and make the correction.


33/75

Users Manual 22 EN

SETUP

SWITCHING BETWEEN THE RECORDING

MODE AND PLAYBACK MODE

Switch between the recording mode (for recording) and the playback mode(for viewing your recorded images).

1 Turn on the camcorder(page 16).

2 Press the play [=]button.h The mode changes.h The mode changes each time the play [=]button is pressed.

3M-S

Full-HD

100-0006

00:00:056.5MB

OK

2010.12.24 18:41

SD

15 000:00:17

Full-HD

OK

Play [=]button


34/75

EN 23 Users Manual

ACCESSING THE MENU SCREEN

1 Set the camcorder to the recording or playback mode(page 22).

2 If the Menu Screen is not displayed, press the MENU button.h The Menu Screen appears.h To cancel the Menu Screen, press the MENU button.

3 Press [G].

3

2

1

23

1

RECORDING MENUVIDEOPHOTOSCENE SELECTFILTER

LED LIGHTSELF-TIMER

OK

1

Full-HD3M-S

OK

MENUbutton


35/75

Users Manual 24 EN

SETUP

4 Press [I] or [J] to select a tab.h The Menu Screen for the selected tab appears.

5 Press [H].

32

1

2

3

1

OK

RECORDING MENUVIDEOPHOTOSCENE SELECTFILTERLED LIGHTSELF-TIMER

1Full-HD

3M-S

OK

Tab

Press [I]

Press [J]Option tab

3

2

1

2

3

1

RECORDING MENUVIDEOPHOTOSCENE SELECTFILTERLED LIGHT

SELF-TIMEROK

1

Full-HD3M-S

OK

Press [H]


36/75

EN 25 Users Manual

6 Press [I] or [J] to select the item you wish to change, and press theOK button.h The Setting Screen for the selected item appears.h To return to the Menu Screen, press the MENU button.

HINTAbout the applicable mode indicatori This indicator shows the shooting mode(s) for which the selected setting is

effective.: This setting is effective during still image shooting.: This setting is effective during video clip recording.

: This setting is effective during still image shooting and video cliprecording.

32

1

23

1

VIDEOPHOTO

SCENE SELECT

FILTER

LED LIGHTSELF-TIMER

OK

Full-HD

3264x2448 2048x1536

2048x1536 2288x1288[16:9] 1920x1080[16:9] 1280x720[16:9]2M0.9M

8M3M-H

3M-S

RECORDING MENU 1

3M-S

3M

OK

OK

PHOTO

OK

Select an item tochange

Applicable mode

Press

Press [I]

Press [J]


37/75

Users Manual 26 EN

S

HOOTING

SHOOTINGSHOOTING

VIDEO CLIP RECORDING

1Turn on the camcorder(page 16), and set it to therecording mode(page 22).

2 Press the [ ] button.h Recording begins.h It is not necessary to keep the

[ ] button pressed whilerecording.

h When the remaining recordingtime available for the currentlyrecording clip becomes little, acountdown of the remainingrecording time appears on thedisplay.

3 End the recording.h

Press the [ ] button againto stop recording.

REC 000:00:09

5

Full-HD2 M

[ ] button

Recording time

Available recordingtime remaining


38/75

EN 27 Users Manual

SHOOTING SINGLE SHOTSCapture a still image (single-shot).

1 Turn on the camcorder(page 16), and set it to therecording mode(page 22).

2 Press the [ ] button.1 Press the [ ] button

halfway.h The autofocus operates,

and the image is focused(focus lock).

2 Continue to gently pressthe [ ] button all theway.h The shutter releases and

the image is captured.h You can view the captured

image on the monitor by

keeping the [ ] buttondepressed when youcapture the image.

3M-S

Target mark

[ ] button


39/75

Users Manual 28 EN

S

HOOTING

HINTAdjusting the monitor brightnessiWhile the Recording Screen is active, you can quickly access the screen

for adjusting the brightness of the monitor by pressing the MENU button forat least 1 second.

What is the camcorder focusing on?iA target mark&on the monitor

shows the area the camcorder isfocusing on.

i The camcorder automaticallydetermines the correct focus bymeasuring from 9 different focuspoints within the shooting area. If thetarget mark is at a position that is

different from the point you wish tofocus on, you can refocus, forexample, by changing the shootingangle.

i The large target mark appears whenthe camcorder focuses on a widearea in the center of the screen.

The focus and exposure can be lockediBy assigning an operation shortcut to an arrow key, you can set the

autofocus or the exposure to a fixed setting. When the exposure setting isfixed, the Picon appears on the monitor; when the autofocus setting isfixed, the picon appears on the monitor.

iWhen the focus range setting or scene select setting is changed, the focuslock is released.

The shutter speed and aperture are displayedi The shutter speed and aperture settings are shown on the Recording

Screen. You can use them as a reference when shooting.If the camcorder shake icon>appears...iDuring still image shooting, if the shutter speed is slow and the possibility

that the image may be blurred due to camcorder shake becomes high, thecamcorder shake icon may appear on the monitor. In this case, use atripod to stabilize the camcorder when shooting.

iWhen shooting with the scene select function set to the fireworks+mode, the camcorder shake icon always appears, but this is normal.

Does it seem to take a long time to save images?iWhen shooting in dimly lit conditions, it may take some time to save the

data to the card.

F2.8

1/2

3M-S

Shutter speed

Aperture

Target mark

Camcorder shake icon


40/75

EN 29 Users Manual

SHOOT A STILL IMAGE WHILERECORDING A VIDEO CLIP

You can capture a still image (a single-shot) while recording a video clip.

1 Turn on the camcorder(page 16), and set it to therecording mode(page 22).

2 Press the [ ] button.

3 When you see a scene youdlike to capture as a still image,press the [ ] button.

4 Press the [ ] button to endthe video clip recording.

HINTiWhen the remaining video recording time becomes approximately

50 seconds, it will no longer be possible to capture a still image whilerecording a video clip. The exact remaining recording time at which thisoccurs will differ depending on the subject and on the recording size, aswell as on the video clip recording mode. If you intend to capture a stillimage while recording a video clip, it is suggested that you take note of theremaining video recording time.

REC 000:00:09

Full-HD2 M

[ ] button

[ ] button


41/75

Users Manual 30 EN

S

HOOTING

About the recording size of still imagesi The size of a still image captured during video clip recording depends on

the video clip recording size.

h It is not possible to capture sequential shots.

Video clip recording size setting Still image recording size

!Y +"& ,

) [


42/75

EN 31 Users Manual

MACRO-PHOTOGRAPHY (ZOOM)Your camcorder has two zoom functions: optical zoom and digital zoom.

1 Point the camcorder lens at thesubject.

2 Push the zoom switch toward[T] or [W] to compose thedesired image.[T]: Zoom in on the subject.[W]: Zoom out.

h When the zoom switch ispushed, the zoom bar appearson the monitor.

h When the optical zoom factoris at maximum, zooming stopstemporarily. When the zoomswitch is pushed toward the[T] side again, the modechanges to the digital zoom

mode and zooming continues.

3 Take the picture.For video clip recording, seepage 26.For shooting single shots, seepage 27.

Zoom switch

Zoom bar

Monitor

When bothoptical and digitalzoom areenabled

Digital zoom (yellow)

Optical zoom

When opticalzoom only isenabled

Pointer


43/75

Users Manual 32 EN

PLAYBAC

K

PLAYBACKPLAYBACK

PLAYING BACK VIDEO CLIPS ANDSTILL IMAGES

1 Set the camcorder to the playback mode(page 22).

2 Select the image to play back.h Use the arrow keys to move

the orange frame to the fileyou wish to play back.

h The image information for

the framed image is shown atthe bottom of the screen.

3 Press the OK button.h The image you selected in

step 2is displayedfullscreen.

h If a video clip was selected,playback begins.

Press [J].

100-0006

00:00:056.5MB

2010.12.24 18:41

OK

Full-HDSD

OK

Orange frame

OK button

Arrow keys


44/75

EN 33 Users Manual

Video clip playback operation

HINTIf theaappears on the playback Screen...i Theaicon appears when playing back a file that was saved in

segments.

To do this... Do this

Normal forward playback Press the OK button.

Stop playback During playback, press [J].

PauseDuring playback, press the OK button or press[I].During accelerated playback, press [I].

To playback one

image at atime (single-frame step)

Forwardplayback

After pausing playback, press [H].

Reverseplayback

After pausing playback, press [G].

Slowplayback

Forward

playback After pausing playback, press and hold [H

].Reverseplayback

After pausing playback, press and hold [G].

Toaccelerate

playback

Forwardplayback

During forward playback, press [H].h The playback speed changes each time

[H] is pressed, as follows:Normal playback 251015

Press [G] to resume normal playback speed.

Reverseplayback

During forward playback, press [G].h The playback speed changes each time

[G] is pressed, as follows:15105

Press [H] to resume normal playback speed.

Return to normal playbackspeed

Press the OK button.

Adjusting the volume

Louder: During playback, push the zoomswitch toward the [T] side.

Softer: During playback, push the zoomswitch toward the [W] side.


45/75

Users Manual 34 EN

PLAYBAC

K

How to save one frame from a video clip as astill image

1 Play back the video clip. Pause the playback at the point you wish tosnap a photo.

2 Press the [ ] button.h The screen to select the aspect ratio of the still image appears. Select

the desired aspect ratio, and press the [ ] button. Note, however,that if the video clip aspect ratio is 4:3, you cannot select 16:9.

HINTThe file size for a video clip is very largei Therefore, be aware that if the video clip is uploaded to a computer to be

played back, the computer may not be able to play back the video fastenough, making it appear jerky. (The video will always be displayedproperly on the camcorder monitor or a television.)

iDepending on the card, recording may end even before the possiblerecording time indicated.

Display the video clip playback pointiDuring video clip playback, press the MENU button for at least 1 second to

display a bar showing the current playback point in the video clip.iPress the MENU button for about 1 second to cancel the bar.

CAUTIONDuring video clip playback, the sound of a motor is audible...iDuring recording, the sound of the optical zoom movement or autofocus

movement was recorded. This is not a malfunction.If no audio is heard...i

The audio is not played back when the video clip is played back in theframe-by-frame, slow-motion, fast playback or reverse playback mode.


46/75

EN 35 Users Manual

ONNECTING TO A TVONNECTING TO A TV

CONNECTING TO A TVBy connecting the camcorder to a TV, you can play back the recorded files onthe TV.

CAUTIONInsert and pull out the cable carefullyiWhen connecting the cables, make sure that the cable plugs are correctly

oriented and that they match the shapes of the terminal sockets on thedevices. Push the plugs in straight when connecting them. If undue force isused to connect a cable, it may permanently damage the connector pins inthe terminal socket.

iDo not use excessive force when connecting and disconnecting cables.

About image output: The image output destination differs depending on thecamcorder status.

m: Images are output n: Images are not output

* When an HDMI cable is used to connect the camcorder to a TV, 1080p

video mode images are output as 1080i images.

Connectioncable

Image outputdestination

Recording mode PlaybackmodeStandby Recording

Dedicated AV

interface cable

Camcordermonitor

NTSC: nPAL: m

m n

TV NTSC: mPAL: n

n m

HDMI cable*

Camcordermonitor

n m n

TV m n m


47/75

Users Manual 36 EN

CONNECT

INGTOA

TV

Connecting to a video input terminalUse the supplied dedicated AV interface cable to connect to a TV.

Connecting to the HDMI terminalUse a separately sold mini-HDMI cable to connect to a TV.

Supplied dedicatedAV interface cableTo USB/AV terminal

Set the input toVIDEO.

White plug: To Audio Input (L) terminal

Red plug: To Audio Input (R) terminal

Yellow plug:To Video Input terminal

Mini HDMI cable

To HDMI terminal

To HDMI terminalon the TV

Set the input toHDMI.


48/75

EN 37 Users Manual

PLAYING BACK ON A TViAfter connecting the camcorder to the television, switch the TV input to the

terminal to which the camcorder is connected.

i The playback method is the same as when viewing images on thecamcorders monitor. (Use the TV controls to adjust the volume.)

i The same playback procedure as when playing back with the camcorder isused to play back audio recordings as well.

CAUTIONInsert and pull out the cable carefullyiWhen connecting the cables, make sure that the cable plugs are correctly

oriented and that they match the shapes of the terminal sockets on thedevices. Push the plugs in straight when connecting them. If undue force isused to connect a cable, it may permanently damage the connector pins inthe terminal socket.

iDo not use excessive force when connecting and disconnecting cables.


49/75

Users Manual 38 EN

APPENDICES

APPENDICESAPPENDICES

FREQUENTLY ASKED QUESTIONSIf you have a question about the camcorder operation, you might find theanswer in this compilation of frequently asked questions.

Question Answer Action

Power

Why doesnt thepower turn on?

Due to coldtemperatures, thebattery packtemporarily lost itspower.

Place the camcorderin your pocket towarm it up beforeusing it.

Why is the batterypack consumed

so quickly evenafter it was fullyrecharged?

The ambienttemperature is

very low.

Keep the batterypack in an

environment of 10 to40 C (50 to 104 F).

The battery packlife has expired.

If a battery becomesdepleted quickly evenafter it was sufficientlycharged, it should beassumed that thebattery has reachedthe end of its service

life. Please replace itwith a new battery.

Why doesntrecharging end?

The battery packlife has expired.

Replace with a newbattery pack. If thisis not effective,consult your dealer.

Why does the

icon

appear?

The remainingbattery packpower is low.

Use the AC adaptor,and DC adaptor(optional) or replace

the battery pack witha fully charged one.

ShootingWhy does themulti-indicatorflash orange?

A recorded file isbeing saved onthe card.

Not a malfunction.Wait until the multi-indicator turns off.


50/75

EN 39 Users Manual

Shooting

Are the settingsretained evenafter thecamcorder is

turned off?

All settings exceptthe self-timer andthe exposurecompensation are

retained even afterthe camcorder isturned off.

Which resolutionsetting should Iuse?

Select the resolutionsetting according tothe intended use.J,y,z,",R,$:Appropriate for

printing letter-size orlarger, and forprinting a close-upof part of a photo(trimming).+,G: Forprinting standardphoto (photoservice) sizes.

,,[: Forphotos displayed ona web page, or sentas e-mailattachments.

What is thedifferencebetween thedigital zoom and

the optical zoom?

Because shootingwith the opticalzoom uses theoptics of a physical

lens, you can shootwithout losingminute details in theimage. The digitalzoom, on the otherhand, works bymagnifying a portionof the image thathits the imagesensor and mayproduce a coarserimage.



51/75

Users Manual 40 EN

APPENDICES

Shooting

How can I get thedistant view intofocus?

Set the scene selectfunction to thelandscape +mode when

photographing.Or, set the focusrange setting tomanual focus-,and set the distanceto .

Monitor

When used incold weather, whydoes the image

seem to leavetraces as itmoves?

Condition due tothe monitorcharacteristics.

Not a malfunction.Spots that appear inthe monitor only

appear in themonitor and will notbe recorded with theimages.Why does the

displayed imagecontain some red,blue and greendots, or why areblack spots

visible?

Viewing

images

Why is the imagetoo bright?

The subject wastoo bright.

When capturing animage, devise a wayto compensate for abright subject, forexample, bychanging theshooting angle.

Why is the image

out of focus?

The focus is not

locked properly.

Hold the camcorder

correctly and slowlypress the [ ]button halfway tolock the focus. Thenpress the [ ]button all the way tocapture the image.



52/75

EN 41 Users Manual

Viewingimages

Why is there noimage (zisshown)?

This may happenwhen trying toplay back imagesstored on a card

from a differentdigital camcorder.

Play back imagesthat were recordedon a card using thiscamcorder.

Why is theplayback imagedistorted?

If the subjectmoves or thecamcorder ismoved duringrecording, adistorted imagemay sometimes

occur.

Not a malfunction.This is acharacteristic of theCMOS sensor.

Why isnt themagnified imageclear?

Due to thecharacteristics ofthe camcorder,magnified imagesappear less clear.

Not a malfunction.

Why isnt thecaptured imageclear?

The image wascaptured usingthe digital zoom.

Not a malfunction.

Can I play backimage and soundfiles that I editedusing mycomputer?

We cannotguarantee theaccurate playback offiles that have beenedited using acomputer.

Why is there amotor-like soundduring video clipplayback?

The sound of thecamcordersmechanical actionwas recorded.

Not a malfunction.

Connectingto a TV

Why is there nosound?

The volume onthe TV is set tothe minimum.

Adjust the volumeon the TV.

Printing

Why does amessage appearduring PictBridgeprinting?

There is aproblem with theprinter.

Please refer to theinstruction manualfor your printer.



53/75

Users Manual 42 EN

APPENDICES

Misc.

The Cannot editvideo clips withunlike settingsmessage

appears.

You haveattempted to joinvideo clips havingdifferent

resolutions orframe rates.

Select video clipsthat have the sameresolution or framerate.

Why is a noiseheard from anearby TV orradio duringbatteryrecharging?

Electromagneticwaves are emittedfrom the charger.

Move the ACadaptor further awayfrom the TV or radiowhen recharging thebattery pack.

Why does theInsufficient cardmemory orInsufficientinternal memorymessage appear?

There is no moreavailable memoryon the card or inthe camcordersinternal memory.

Delete unnecessaryfiles, or use a cardthat has morememory available.

Why does theCard isprotectedmessage appear?

The lock switchon the card is inthe locked(protect) position.

Move the lockswitch to theunlocked position.

Why cant thecamcorder beoperated?

A temporaryinternal circuitryproblem may bethe cause.

Remove the ACadaptor and thebattery pack fromthe camcorder, waita few minutes, thenreinstall the batterypack and try again.

A problem suchas inability to

record or playback occurs.

The card containsfiles that were

saved using adevice other thanthis camcorder.

After saving yourfiles to a different

medium, format thecard.



54/75

EN 43 Users Manual

Misc.

Can I use mycamcorderabroad?

When thecamcorder isconnected to a TV,you can switch the

camcorders videooutput to NTSC orPAL. If you havequestions aboutaccessories etc.,please consult witha dealer near you foradvice.

Why does theSystem errormessage appear?

A problem hasoccurred withinthe camcorder orcard.

Check the followingitems:1 Remove the

card and theninstall it again.

2 Remove thebattery pack andthen install itagain.

3 Install a differentcard.

If System error stillappears afterperforming theabove steps, thentake the camcorderto the dealer forservice.



55/75

Users Manual 44 EN

APPENDICES

OVERVIEW OF THE MENU SCREEN

Recording Menu

3

2

1

2

3

1

Full-HD3M-S

RECORDING MENUVIDEOPHOTO

SCENE SELECTFILTERLED LIGHTSELF-TIMER

OK

1

7

6

5

4

3

2

1

OK


56/75

EN 45 Users Manual

1 Video clip settings

2 Still image settings

3 Scene select

4 Filter

5 LED light setting

6 Self-timer

7 Remaining battery powerindication

!: Record at 1920 1080pixels, 60 fields/s (60i).

Y: Record at 1920 1080pixels, 30 fps (30p).

": Record at 1280 720pixels, 60 fps (60p).

&: Record at 1280 720pixels, 30 fps (30p).

): Record at 640 480 pixels,30 fps.


57/75

Users Manual 46 EN

APPENDICES

7

5

4

3

21

3

2

1

2

3

1

6

RECORDING MENU

VIDEO STABILISER

FOCUS

PHOTO STABILISER

FOCUS MODE

EXP MEASURE

ISO

OK

2

OK


58/75

EN 47 Users Manual

1 Video stabiliserh Compensate for camcorder

shake during video cliprecording.

2 Photo stabiliserh Compensate for camcorder

shake during still imageshooting.

3 Focus rangeh Select the focus range that

corresponds to the distance tothe subject.

4 Focus mode

5 EXP measure

6 ISO sensitivity

h The indicated ISO value is thestandard output sensitivity.

7 Remaining battery power

indication

\: Record with imagestabiliser on.

]: Record without imagestabiliser.

\: Shoot with image stabiliser

on.]: Shoot without image

stabiliser.

*: The camcorder

automatically focuses onthe subject with a range of10 cm (3.94 in.) to infinity(normal).

-: The focus can be setmanually.

+: The camcorder focuses onthe subject within a rangeof 1 cm (0.39 in.) to 80 cm(2.62 ft.) (super macro).

B: 9-point range finder focus

C: Spot focus

X: Multi-section lightmeasuring

W: Center-weighted lightmeasuring

Y: Spot light-measuring

=: Sensitivity is setautomatically (video cliprecording: ISO 50 to 800;still image shooting: ISO 50to 400)

*: Sets sensitivity to ISO 50

u: Sets sensitivity to ISO 100

v: Sets sensitivity to ISO 200

w: Sets sensitivity to ISO 400

6: Sets sensitivity to ISO 800

-: Sets sensitivity to ISO 1600


59/75

Users Manual 48 EN

APPENDICES

7

5

4

3

21

3

21

2

3

1

6

RECORDING MENU

WHITE BALANCEEXPOSURE

TARGET A SUBJECT

HIGH SENSITIVITY

DIGITAL ZOOM

REC FOLDER

3

OKOK


60/75

EN 49 Users Manual

1 White balance

2 Exposure

3 Target a subjectAutomatically target a specificcolor with the color chaserfunction, or capture sharp face

shots with the face chaserfunction.

4 High sensitivity mode

5 Digital zoom

6 Rec folder setting


>: White balance isautomatically adjusteddepending on the ambientlighting (auto).

r: For shooting in sunnyconditions (fair).

o: For shooting in overcastconditions (cloudy).

p: For shooting underfluorescent lighting(fluorescent).

q: For shooting under

incandescent lighting(incandescent).

^: For setting the mostaccurate white balance(one push).

@: The exposure is setautomatically.

T: Set the shutter speedmanually.

g: Set the aperture manually.

H: Set the aperture andshutter speed manually.

-: Enable face chaser.

(: Enable color chaser.

): Disable face chaser andcolor chaser.

1: Increased sensitivity.

2: Normal sensitivity.

Q: Enable the digitalzoom.

B: Disable the digitalzoom.


61/75

Users Manual 50 EN

APPENDICES

Playback Menu

4

3

7

5

6

2

12

1

2

3

1

PLAYBACK MENU

SLIDESHOW

PLAY VOLUME

PROTECT

DELETE

ROTATE

1

OKRESIZE

OK

1 Slideshowh Specify the slideshow settings

and play the slideshow.

2 Playback volumeh Adjust the volume for video clip

and audio file playback.

3 Protecth File protect setting (delete

prohibited)

4 Deleteh Delete files.

5 Rotateh Rotate a still image.

6 Resizeh Reduce the resolution of a still

image.



62/75

EN 51 Users Manual

4

3

6

5

212

2

1

3

1

PLAYBACK MENU

EDIT PHOTO

PRINT INSTRUCTIONSEDIT VIDEO

SELECT FOLDERCOPY

2

OKOK

1 Edit photoh Repair the red-eye caused by

the LED light, or enhance thecontrast (still images only).

2 Video clip edith Edit video clips.

3 Printing instructionsh Specify the printing instructions

(DPOF settings).

4 Select folderh Select a folder to play back.

5 Copyh Copy files from the card to the

internal memory, or vice versa.

6 Remaining battery power

indication


63/75

Users Manual 52 EN

APPENDICES

Option Menu

3

2

1

2

3

1

OK

OPTION MENUCLOCK SETINFO DISPLAYSTARTUP DISPLAYOPERATION BEEPPOST VIEW

1

OK 6

5

4

3

2

1


64/75

EN 53 Users Manual

1 CLOCK SET settingh Set the camcorders clock.

2 INFO DISPLAY settingh Specify the information to

display on the playback

screen.SHOW ALL:

Display the capture date andplayback time (video clips).

DATE & TIME:Display the capture date.

COUNTER:Display the playback timewhen playing back a video

clip.OFF:

Do not display the capturedate or playback time.

3 STARTUP DISPLAY settingh Select the display that appears

on the monitor when thecamcorder is turned on in therecording mode.

4 OPERATION BEEP settingh Settings for the camcorders

operation sounds, audio guideand volume.TURN ON/OFF:

Mute or enable the soundswhen the camcorder isturned on or off.

SHUTTER:Select the sound that isproduced when the [ ]button is pressed.

KEY SW:Select the sound that is

produced when the OKbutton, MENU button, etc.are pressed.

OPERATION VOL:Adjust the volume of theoperation sounds.

5 POST VIEW settingh Specify the duration that the

captured image is shown on

the monitor (post-view) afterthe [ ] button is pressed.

6 Remaining battery chargedisplay


65/75

Users Manual 54 EN

APPENDICES

5

4

3

21

3

2

1

2

3

1

6

SHORTCUTS

OPTION MENU

NOISE REDUCTIONIMAGE SETTINGSBRIGHTNESSLANGUAGE

2

OKOK

1 SHORTCUTS setting

2 NOISE REDUCTION settingh Compared to normal shooting,

when the PHOTO NR functionis ON, the image processingtime after shooting a still image

is slightly longer.VIDEO NR:

Turn ON/OFF the imagenoise reduction functionduring video clip recording.

PHOTO NR:Turn ON/OFF the imagenoise reduction functionduring still image shooting.

WIND SOUND NR:Turn ON/OFF the wind noisereduction function duringvideo clip/audio shooting.

3 Image quality settingh Set the vividness and

sharpness of the images.

4 BRIGHTNESS settingh Adjust the brightness of the

camcorders monitor display.

5 LANGUAGE settingh Select the language in which

the monitor messages aredisplayed.



66/75

EN 55 Users Manual

5

4

3

23

2

1

2

3

1

6OK

OPTION MENU 3

POWER SAVEFILE NO. CONT'DFORMATRESET SETTINGS

OK

1TV OUTPUT

1 TV OUTPUT settingh Note: 1080p playback is not

available via HDMI, only viaUSB to PC.

2 POWER SAVE settingh Specify the elapsed period of

inactivity before the powersave mode (to conservebattery power) is activated.

3 FILE NO. CONTD setting

4 FORMAT

5 RESET SETTINGSh Reset the camcorder settings

to the factory-preset settings.h The following settings do not

change with this procedure:Date and time settingTV system settingLanguage setting



67/75

Users Manual 56 EN

APPENDICES

SPECIFICATIONS

Camcorder

Camileo SX900

Image Sensor 14Mega Pixel CMOS Sensor

Operation Modes Movie Record, Picture Record

Lens f=3.2~28.8mm;F2.8~3.0

Focus Range (wide)Macro:1cm~80cmNormal:10cm~infinite

Zoom 1~90 (9Optical + 10Digital)

Shutter ElectronicLCD monitor 2.7"LCD

Storage Media SD/SDHC/SDXC

Image Resolution

3264 2448 8M2048 1536 3M2288 1288 3M(16:9)1600 1200 2M1920 1080 2M(16:9)1280 720 0.9M(16:9)

640 480 0.3M

Movie Resolution

1920 1080i 60field/s1920 1080p 30fps1280 720p 60fps1280 720p 30fps640 480p 30fps

White Balance Auto/Manual

Exposure Auto/Manual

Self-timer 2 second delay, 10 second delay

Light On/Off

File-FormatPicture:JPEGMovie:Mpeg-4 AVC/H.264

Image play Single Image/Slideshow

PC interface USB 2.0 Port

TV out NTSC/PAL Selectable,mini HDMI

Battery Lithium-ion Rechargeable Battery

Dimension 55.4(H)*33.0(W)*110.0(D) mm

Weight 152g(Without battery)

Li-ion battery pack Type name PX1686

AC adaptor Type name TSB-1


68/75

EN 57 Users Manual

Concerning the multi-indicatorThe camcorders multi-indicator will light, flash, or be off, depending on thedifferent camcorder operations.

Color Multi-indicator status Camcorder status

GreenLit Connected to a computer or printer

Flashing Power save mode active

Orange

LitConnected to a TVCharging

Flashing

SlowBattery charge error or rise ininternal temperature

Fast During self-timer photography

Very fast Accessing card


69/75

Users Manual 58 EN

APPENDICES

OthersMac OS is a trademark of Apple Inc., registered in the U.S. and othercountries.Microsoft and Windows are registered trademarks of Microsoft Corporation in

the USA and other countries.Intel and Pentium are registered trademarks of Intel Corporation (USA).In this manual, the MicrosoftWindows2000 operating system, MicrosoftWindowsXP operating system, MicrosoftWindowsVista operatingsystem, and MicrosoftWindows7 operating system are collectivelyreferred to as Windows.

Software Red Eye by FotoNationTM2003-2005 is a trademark of FotoNationInc.

Red Eye software

2003-2005 FotoNation In Camcorder Red Eye - coveredby U.S. Patent No. 6,407,777. Other patents Pending.

SDXC logo is a trademark.

All other company and product names are registered trademarks ortrademarks of their respective owners.

CAUTIONi It is forbidden to copy this manual, whole or in part, without prior written

permission.iAll images and illustrations given in this manual are for explanation

purposes and may differ slightly from that of the actual product. Also,actual specifications are subject to change without prior notice andtherefore may differ from the contents of this manual.


70/75

EN 59 Users Manual

TOSHIBA SUPPORTNeed help?For the latest driver updates, Users Manuals & FAQs please have a look at

the TOSHIBA options & services support page:computers.toshiba.eu/options-support

Please seecomputers.toshiba.eu/options-warrantyfor the TOSHIBA hotline numbers.


71/75

Users Manual 60 EN

APPENDICES

REGULATORY INFORMATIONCE compliance

This product is CE marked in accordance with the requirements of theapplicable EU Directives. Responsible for CE marking is Toshiba EuropeGmbH, Hammfelddamm 8, 41460 Neuss, Germany. A copy of the officialDeclaration of Conformity can be obtained from following website:http://epps.toshiba-teg.com.

Working EnvironmentThe Electromagnetic Compliance (EMC) of this product has been verifiedtypically for this product category for a so called Residential, Commercial &Light Industry Environment. Any other working environment has not beenverified by Toshiba and the use of this product in these working environmentsis maybe restricted or cannot be recommended. Possible consequences ofthe use of this product in non verified working environments can be:Disturbances of other products or of this product in the nearby surroundingarea with temporarily malfunction or data loss/corruption as result. Example

of non verified working environments and related advices:Industrial environment (e.g. where 3-phase 380V mains is being usedmainly): Danger of disturbances of this product due to possible strongelectromagnetic fields especially near to big machinery or power units.

Medical environment: The compliance to the Medical Product Directive hasnot been verified by Toshiba, therefore this product cannot be used as amedical product without further verification. The use in usual officeenvironments e.g. in hospitals should be no problem if there is no restrictionby the responsible administration.

Automotive environment: Please search the owner instructions of the relatedvehicle for advices regarding the use of this product (category).

Aviation environment: Please follow the instructions of the flight personnelregarding restrictions of use.


72/75

EN 61 Users Manual

Additional environments not related to EMCOutdoor use: As a typical home/office equipment this product has no specialresistance against ingress of moisture and is not strong shock proofed.

Explosive atmosphere: The use of this product in such special working

environment (Ex) is not allowed.

REACH

Following information is only valid for EU-member States:REACH - Compliance StatementThe new European Union (EU) chemical regulation, REACH (Registration,Evaluation, Authorization and Restriction of Chemicals), entered into force on1 June 2007.

Toshiba will meet all REACH requirements and is committed to provide ourcustomers with information about the chemical substances in our productsaccording to REACH regulation.

Please consult the following website http://www.toshiba-europe.com/computers/info/reach for information about the presence in our articles ofsubstances included on the candidate list according to article 59(1) ofRegulation (EC) No 1907/2006 (REACH) in a concentration above 0.1 %weight by weight.

WEEE

Following information is only valid for EU-member States:Disposal of productsThe crossed out wheeled dust bin symbol indicates thatproducts must be collected and disposed of separately fromhousehold waste. Integrated batteries and accumulators can

be disposed of with the product. They will be separated at therecycling centres.

The black bar indicates that the product was placed on themarket after August 13, 2005.

By participating in separate collection of products and batteries, you will helpto assure the proper disposal of products and batteries and thus help toprevent potential negative consequences for the environment and humanhealth.


73/75

Users Manual 62 EN

APPENDICES

For more detailed information about the collection and recycling programmesavailable in your country, please visit our website (http://eu.computers.toshiba-europe.com) or contact your local city office or theshop where you purchased the product.

Disposal of batteries and/or accumulatorsThe crossed out wheeled dust bin symbol indicates thatbatteries and/or accumulators must be collected anddisposed of separately from household waste.

If the battery or accumulator contains more than the specifiedvalues of lead (Pb), mercury (Hg), and/or cadmium (Cd)defined in the Battery Directive (2006/66/EC), then thechemical symbols for lead (Pb), mercury (Hg) and/or

cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.By participating in separate collection of batteries, you will help to assure theproper disposal of products and batteries and thus help to prevent potentialnegative consequences for the environment and human health.

For more detailed information about the collection and recycling programmesavailable in your country, please visit our website (http://eu.computers.toshiba-europe.com) or contact your local city office or theshop where you purchased the product.


74/75

EN 63 Users Manual

ADDITIONAL INFORMATION 2010 TOSHIBA Europe GmbH. All rights reserved.TOSHIBA reserves the right to make technical changes. TOSHIBA assumes

no liability for damages incurred directly or indirectly from errors, omissions ordiscrepancies between this product and the documentation.


75/75

toshiba camileo

Documents