toyota corolla 2009 - keyless entry...

P/N Qty Description

Phillip screwdriver Straight-Slot screwdriverRatchet w/extension 10 mm socketDiagonal wire cutters Common pliersFlashlight Nylon trim tool Torque Wrench 36in. lbs.

Kit Contents

Hardware Bag Contents

Conflicts

Legend * Mandatory

STOP: Damage to the vehicle may occur. Do notproceed until process has been complied with.OPERATOR SAFETY: Use caution to avoidrisk of injury.CRITICAL PROCESS: Proceed with caution toensure a quality installation. These points will beaudited on a completed vehicle installation.TOOLS & EQUIPTMENT: This calls out thespecific tools and equipment required for thisprocess.REVISION MARK: This mark highlights achange in installation with respect to previousissue.

Recommended Tools

SPECIAL NOTE: Installation Sequences

After TMS and Safety mandated preparatory steps have been taken,the installation sequence is the suggested method for completing theaccessory installation. In some instances the suggested sequence iswritten for one associate to install and in others the sequence is givenas part of a team accessory installation. Unless otherwise stated inthe document, the associates may perform the installation steps inany order to make the installation as efficient as possible whilemaintaining consistent quality.

Safety Tools

Special Tools

INSTALLATION TOOLS

Special Chemicals

Vehicle Service Parts (may be required for reassembly)

Item # Quantity Reqd Description1 1 Keyless Module2 1 Main Harness3 1 Hardware Bag4 1 Valet Switch5 2 24" Cable Ties6 2 3-Button Transmitters

Item # Quantity Reqd Description1 8 Red T-Taps2 2 Blue T-Taps3 6 8" Cable Ties4 1 2-1/4"x 2-1/4" Foam Pad5 1 Yellow T-Tap

NOTE: Not for installation on vehilce's equipped withfactory installed keyless entry.

00016-79200-01 1 Keyless Entry Control Module00016-34030-05 2 Keyless Entry Transmitter00016-32901-01 1 Main Wiring Harness00016-30960-56 1 On/Off Toggle Control Switch00016-32901-02 1 Miscellaneous Hardware Kit00016-35105-01 1 Headlight Extension Wire

Toyota Corolla 2009 - Keyless Entry System

Part Number: 00016-32901Accessory Code: KE1

Southeast Toyota Distributors, LLC of 11

iustyfa

Stamp

iustyfa

Text Box

Document: 03.09.00 PIO / DIO Rev. E 05/21/08

INSTALLATION PREPARATION

Before starting installation

1. Familiarize yourself with the installation instructions.2. Inspect kit components.

VEHICLE PREPARATION

1. Place protective coverings on vehicle.

2. Disconnect negative battery clamp

Negative Battery Cable

3. Remove the driver's side scuff plate.Inserting a plastic panel tool under thescuff plate and prying upward todisengage the snap clips.

4. Remove the driver side kick panel byinserting a plastic panel tool under the kickpanel and carefully pry to disengage thesnap clips.

TOYOTA COROLLA KEYLESS ENTRY SYSTEM


Optional step: Insert a plastic tool under the front

of the stuff plate & driver side kick panel lift only that area.

,

5. Remove (2) Phillips screws,from thedriver's lower finish panel (right side). Pullthe lower finish panel outward from thevehicle dash to disengage the snap clips.

7. Carefully seperate the lower steeringcolumn cover halfs by disengaging the (4)tabs and remove cover.

6. Pull the lower finish panel (left side)outward from the vehicle dash todisengage the snap clips.



iustyfa

Text Box

Option Step

iustyfa

Text Box

Option Step

IMPORTANT ! After installation, inspect & insure that all Keyless SystemHarness are clear of all HOT, SHARP or MOVING objects

CONNECTING THE KEYLESS SYSTEMHARNESS:

1. Carefully follow the wiring diagram andfactory connector details on pages 5&6 forTMC vehicle's and pages 7&8 for NUMMIvehicle's.

T-TAP INSTALLATION:

A. When installing female T - Tap connectors, be sure the wire is located inside the wire channel of thefemale T - Tap connector before closing connector over the wire with pliers.

Step A Step B Step C

T - Tap Wire from main keylessharness

MOUNTING MAIN CONTROL MODULE:

A. Secure the main module to the vehicleharness connected to the JB in the driver'sside kick panel area. Secure in place withthe long cable ties provided.

NOTE: Guide long cable through themodule eyelets as shown.

Keyless Module

INSTALLING PROCEDURES



NOTE: DO NOT WRAP OR BUNDLE ANTENNA HARNESS.Module antenna wire must extend up as high as possibleand secured in place for the best signal reception.

iustyfa

Line

iustyfa

Line

WIRING DIAGRAM COROLLA (TMC)W

IRIN

G D

IAG

RA

M

PIN

K [

Doo

r Lo

ck S

witc

h]:

Use

a r

ed T

-Tap

and

conn

ect t

o th

e LT

. BLU

E w

ire in

con

nect

or IE

2,lo

catio

n 16

.

PIN

K/W

HIT

E [

Doo

r Unl

ock

Switc

h]: U

se a

red

T-Ta

p an

d co

nnec

t to

the

YELL

OW

wire

in c

onne

ctor

IE2,

loca

tion

15.

PIN

K/W

HIT

E [D

oor U

nloc

k D

etec

t Sw

itch]

: Use

are

d T-

Tap

and

conn

ect

to t

he Y

ELLO

W w

ire i

nco

nnec

tor

IE1,

loca

tion

9.

WH

ITE

[Driv

er D

oor U

nloc

k M

otor

- To

war

ds D

oor

Lock

] - (S

ee D

etai

l A B

elow

)

BLU

E/W

HIT

E [ D

river

Doo

r Unl

ock

Mot

or - T

owar

dsB

ody

ECU

] - (S

ee D

etai

l A B

elow

)

RED

[+12

VDC

Bat

tery

]: Us

e a

red

T-Ta

p an

d co

nnec

tto

the

YELL

OW

wire

in c

onne

ctor

E4,

loca

tion

2.

YELL

OW

[ +1

2VD

C A

cces

sory

]: U

se a

red

T-Ta

pan

d co

nnec

t to

the

BLA

CK

wire

in c

onne

ctor

E4,

loca

tion

3.

CH

ASS

IS G

RO

UN

D -

Con

nect

the

ring

term

inal

to th

e 10

mm

bolt

at th

e dr

iver

's s

ide

kick

pan

el. (

fact

ory

grou

nd)

GR

EEN

/RED

WIR

E [H

orn]

: Use

red

T-Ta

p an

d co

nnec

t to

the

LT. G

REE

N W

IRE

in c

onne

ctor

E6,

loca

tion

8.

WH

ITE

WIR

E [T

ail L

ight

s]: U

se re

d T-

Tap

and

conn

ect t

o th

eW

HIT

E W

IRE

in c

onne

ctor

E8,

loca

tion

18.

2 Pi

n M

olex

Con

nect

or -

Plug

into

Tog

gle

Con

trol

Switc

h.

DET

AIL

"A

"

DR

IVER

'S D

OO

R U

NLO

CK

CIR

CU

IT

Cut

the

GR

EEN

WIR

E in

con

nect

or IE

2, lo

catio

n17

. St

rip t

he in

sula

tion

from

bot

h si

des

of t

hecu

t w

ire,

and

crim

p th

e W

HIT

E W

IRE

from

the

keyl

ess

harn

ess

to th

e H

AR

NES

S si

de o

f the

cut

wir

e. C

rim

p th

e B

LUE

/WH

ITE

WIR

E f

rom

the

keyl

ess

harn

ess

to th

e C

ON

NEC

TOR

sid

e of

the

cut

wire

.

Harn

ess

Wire

s

BLU

E w

/W

HIT

E

Cut

& S

trip

Exis

ting

Wire

WH

ITEB

LUE

WIR

E [H

eadl

ight

s - A

utom

atic

Tra

nsm

issi

on V

ehic

le]:

Use

red

T-Ta

p an

d co

nnec

t to

the

BLA

CK

WIR

E in

con

nect

orA

E11,

loca

tion

6. R

efer

to

page

6 f

or a

dditi

onal

det

ails

.

BLU

E W

IRE

[Hea

dlig

hts

- M

anua

l Tr

ansm

issi

on V

ehic

le]:

Con

nect

BLU

E ex

tens

ion

harn

ess

to t

he a

larm

BLU

E w

ire.

Use

red

T-Ta

p an

d co

nnec

t to

the

BLA

CK

WIR

E in

con

nect

orE9

1, lo

catio

n 6.

Ref

er t

o pa

ge 6

for

add

ition

al d

etai

ls.


iustyfa

Line

iustyfa

Line

5. CONNECTOR E91 : Headlights (MT)Location : Behind glove box

Manual Transmission Vehicle's

Pin 6Black

Headlights

ALARM CAR BLUE** Black(Extension Wire)

Nummi Made Vehicle

1 23 4 5 6 7 8 9 10 11

12 13 14 15 16 17 18 19 20

** Locate the BLUE extension wire harness inthe security kit. Attach the extension wire tothe alarm BLUE wire and route to the glovebox, passenger side area. Attach the vehicleBLACK wire, pin 6, as pictured above.

2. CONNECTOR E6 : HornLocation : Lower Steering Column Cover Area

Pin 8Lt. Green

Horn

CONNECTOR DETAILS: COROLLA (TMC)

3. CONNECTOR E8 : TailightsLocation : Lower Steering Column Cover Area

Pin 18White

Tail Lights

KEYLESS CARWhite White

1 2 3 4

5 6 7 8

1. CONNECTOR E4 : Ignition SwitchLocation : Steering Column

1 2 3 4 5 6 7 8 9 10

11 12 13 14 15 16 17 18 19 20

KEYLESS CARGreen/Red Lt. Green

KEYLESS CARRed YellowYellow Black

Pin 2Yellow

+12V Battery

Pin 3Black

+12V Accessory

121097

641 3 5

11

2

8

4. CONNECTOR AE11 : Headlights (AT)Location : High up in cowl, left of instrument panelAutomatic Transmission Vehicle's

Pin 6Black

Headlights

KEYLESS CARBlue Black

4

9

53 6 7

13 1412 15 16

82

18

1

1711107 6 5 4 3

15 1416 13 12

1289

10111718

For manual transmission vehicle's, refer toStep 5, this page.

Black Connector

White Connector

White Connector

White Connector


4

9

53 6 7

13 1412 15 16

82

18

1

1711107 6 5 4 3

15 1416 13 12

1289

10111718

6. CONNECTOR IE2 : Door LocksLocation : Driver's Kick Panel Area

CONNECTOR DETAILS: COROLLA (TMC)

Door Lock SwitchBlue WireLocation 16

Door Unlock SwitchYellow WireLocation 15

Driver's Door Lock MotorLt. Green WireLocation 17**

Door Unlock Detect SwitchYellow WireLocation 9

KEYLESS CARPink BluePink/White YellowWhite Lt.Green (Lock Side)Blue/White Green (ECU Side)

** This vehicle wire must be cut in half, refer to page 5 for instructions.

7. CONNECTOR IE1 : Unlock DetectLocation : Driver's Kick Panel Area

KEYLESS CARPink/White Yellow

1 23 4 5 6 78 9 10 11 12

12

34567

89101112

White Connector Blue Connector


WIRING DIAGRAM COROLLA (NUMMI)W

IRIN

G D

IAG

RA

M

PIN

K [

Doo

r Lo

ck S

witc

h]:

Use

a r

ed T

-Tap

and

conn

ect

to t

he V

IOLE

T w

ire in

co

nnec

tor

IE2,

loca

tion

16.

PIN

K/W

HIT

E [

Doo

r Unl

ock

Switc

h]: U

se a

red

T-Ta

p an

d co

nnec

t to

the

BEI

GE

wire

in c

onne

ctor

IE2,

loca

tion

15.

PIN

K/W

HIT

E [D

oor U

nloc

k D

etec

t Sw

itch]

: Use

are

d T-

Tap

and

conn

ect

to t

he Y

ELLO

W w

ire i

nco

nnec

tor

IE1,

loca

tion

9.

WH

ITE

[Driv

er D

oor U

nloc

k M

otor

- To

war

ds D

oor

Lock

] - (S

ee D

etai

l A B

elow

)

BLU

E/W

HIT

E [ D

river

Doo

r Unl

ock

Mot

or - T

owar

dsB

ody

ECU

] - (S

ee D

etai

l A B

elow

)

RED

[+12

VDC

Bat

tery

]: Us

e a

red

T-Ta

p an

d co

nnec

tto

the

RED

wire

in c

onne

ctor

E4,

loca

tion

2.

YELL

OW

[ +1

2VD

C A

cces

sory

]: U

se a

red

T-Ta

pan

d co

nnec

t to

the

GR

AY w

ire in

con

nect

or E

4,lo

catio

n 3.

CH

ASS

IS G

RO

UN

D -

Con

nect

the

ring

term

inal

to th

e 10

mm

bolt

at th

e dr

iver

's s

ide

kick

pan

el. (

fact

ory

grou

nd)

GR

EEN

/RED

WIR

E [H

orn]

: Use

red

T-Ta

p an

d co

nnec

t to

the

LT. G

REE

N W

IRE

in c

onne

ctor

E6,

loca

tion

8.

WH

ITE

WIR

E [T

ail L

ight

s]: U

se re

d T-

Tap

and

conn

ect t

o th

eB

RO

WN

WIR

E in

con

nect

or E

8, lo

catio

n 18

.

2 Pi

n M

olex

Con

nect

or -

Plug

into

Tog

gle

Con

trol

Switc

h.

Harn

ess

Wire

s

BLU

E w

/W

HIT

E

Cut

& S

trip

Exis

ting

Wire

WH

ITE

DET

AIL

"A

"

DR

IVER

'S D

OO

R U

NLO

CK

CIR

CU

IT

Cut

the

GR

EEN

WIR

E in

con

nect

or IE

2, lo

catio

n17

. St

rip t

he in

sula

tion

from

bot

h si

des

of t

hecu

t w

ire,

and

crim

p th

e W

HIT

E W

IRE

from

the

keyl

ess

harn

ess

to th

e H

AR

NES

S si

de o

f the

cut

wir

e. C

rim

p th

e B

LUE

/WH

ITE

WIR

E f

rom

the

keyl

ess

harn

ess

to th

e C

ON

NEC

TOR

sid

e of

the

cut

wire

.

BLU

E W

IRE

[Hea

dlig

hts

- Aut

omat

ic T

rans

mis

sion

Veh

icle

]:U

se re

d T-

Tap

and

conn

ect t

o th

e VI

OLE

T W

IRE

in c

onne

ctor

AE1

1, lo

catio

n 6.

Ref

er t

o pa

ge 9

for

add

ition

al d

etai

ls.

BLU

E W

IRE

[Hea

dlig

hts

- M

anua

l Tr

ansm

issi

on V

ehic

le]:

Con

nect

BLU

E ex

tens

ion

harn

ess

to t

he a

larm

BLU

E w

ire.

Use

red

T-T a

p an

d co

nnec

t to

the

VIO

LET

WIR

E in

con

nect

orE9

1, lo

catio

n 6.

Ref

er t

o pa

ge 9

for

add

ition

al d

etai

ls.


iustyfa

Line

iustyfa

Line

5. CONNECTOR E91 : Headlights (MT)Location : Behind glove box

Manual Transmission Vehicle's

Pin 6Violet

Headlights

ALARM CAR Blue** Violet(Extension Wire)

Nummi Made Vehicle

1 23 4 5 6 7 8 9 10 11

12 13 14 15 16 17 18 19 20

** Locate the BLUE extension wire harness inthe security kit. Attach the extension wire tothe alarm BLUE wire and route to the glovebox, passenger side area. Attach the vehicleVIOLET wire, pin 6, as pictured above.

2. CONNECTOR E6 : HornLocation : Lower Steering Column Cover Area

Pin 8Lt. Green

Horn

KEYLESS CARGreen/Red Lt. Green

121097

641 3 5

11

2

8

CONNECTOR DETAILS: COROLLA (NUMMI)

3. CONNECTOR E8 : TailightsLocation : Lower Steering Column Cover Area

Pin 18Brown

Tail Lights

1 2 3 4

5 6 7 8

1. CONNECTOR E4 : Ignition SwitchLocation : Steering Column

1 2 3 4 5 6 7 8 9 10

11 12 13 14 15 16 17 18 19 20

Pin 2Red

+12V Battery

Pin 3Gray

+12V Acessory

4. CONNECTOR AE11 : Headlights (AT)Location : High up in cowl, left of instrument panelAutomatic Transmission Vehicle's

Pin 6Violet

Headlights

KEYLESS CARBlue Violet

4

9

53 6 7

13 1412 15 16

82

18

1

1711107 6 5 4 3

15 1416 13 12

1289

10111718

KEYLESS CARRed RedYellow Gray

KEYLESS CARWhite Brown

For manual transmission vehicle's, refer toStep 5, this page.

White Connector

Black Connector

White Connector

White Connector


CONNECTOR DETAILS: COROLLA (NUMMI)

Door Unlock Detect SwitchYellow WireLocation 9

7. CONNECTOR IE1 : Unlock DetectLocation : Driver's Kick Panel Area

KEYLESS CARPink/White Yellow

1 23 4 5 6 78 9 10 11 12

12

34567

89101112Wh

White Connector

4

9

53 6 7

13 1412 15 16

82

18

1

1711107 6 5 4 3

15 1416 13 12

1289

10111718

6. CONNECTOR IE2 : Door LocksLocation : Driver's Kick Panel Area

Door Lock SwitchViolet WireLocation 16

Door Unlock SwitchBeige WireLocation 15

Driver's Door Lock MotorGreen WireLocation 17**

KEYLESS CARPink VioletPink/White BeigeWhite Green (Lock Side)Blue/White Green (ECU Side)

** This vehicle wire must be cut in half, refer to page 7 for instructions.

White Connector


COMPLETING THE INSTALLATION: COROLLA

TESTING THE SYSTEM:

1. Prior to delivering the vehicle, test allfeatures of the system accordinng to theowner's manual included.

LOCK - Press and release the LOCK buttonon the transmitter. All doors should lock,headlights should come on.

UNLOCK - Press and release the UN-LOCK button on the transmitter. The driver'sdoor should unlock, headlights should comeon.

Press and release the UNLOCK buttonagain. All doors should unlock.

Press and hold the PANIC button. The hornshould sound and the parkings lights shouldflash.

Press and release the PANIC button tosilence the horn.

NOTE: Be sure to test both transmitter thatwere included in the kit.

ASSEMBLE ALL REMOVED PANELS TOTHE VEHICLE:

1. Refer again to the vehicle repair manualand reassemble all panels that were removedfor installation back onto the vehicle. Testthoroughly, all mechanical componentsdisconnected and or removed from thevehicle during the installation of thisaccessory.

PREPARING THE VEHICLE FOR DELIVERY:1. To set the arm/disarm chirps to "soft"chirps.

2. Start with the doors in the unlockedposition, Toggle Control Switch in the "OFF"position.

3. Turn the ignition key to the on position.

4. Turn the ignition key off, then immediatelyswitch the Toggle Control Switch "ON" then"OFF" 4 times.

5. The vehicle horn should respond with softhorn chirps.


Note: Re-torque battery cable to 36in lb. once process is completed.

Negative Battery Cable

toyota corolla 2009 - keyless entry...

Documents