training purposes only jem microbe-i 31407 jmu-081192 (ver. 1.2) 1 notice : this technical data is...
TRANSCRIPT
1 Training Purposes OnlyJEM MICROBE-I 31407JMU-081192 (Ver. 1.2)
Notice : This technical data is furnished on the condition that it will be used by and disclosed to the receiving Cooperating agency and its contractors and sub contractors only for the purposes of fulfilling the cooperating agency’s responsibilities under the Space Station Intergovernmental Agreement (IGA) and Memorandum of Understanding (MOU). It shall not be used for any other purpose, nor disclosed or retransferred to any other entity or government without prior written permission of the Japan Aerospace Exploration Agency (JAXA).
Microbe-I
JEM MICROBE-I 31407
Instructor: Takashi Yamasaki Satoshi Kawaguchi
2 Training Purposes OnlyJEM MICROBE-I 31407JMU-081192 (Ver. 1.2)
Objectives
After this lesson the trainee will be able to:
- Explain the science objective of the Microbe-I experiment.
- List onboard outcomes from performing Microbe-I experiment.
- List two sampling methods of Microbe-I experiment.
- Explain what crew has to do to Microbial Detection Sheet after sampling to prevent bio contamination.
- Explain what crew has to do with BZK Wipe after Microbial Detection Sheet sampling to prevent bio contamination.
- Explain what crew must NOT contaminate throughout sampling.
- Identify the area on Microbial Detection Sheet Yeast and Mold where crew must NOT touch.
- Identify the area on Blue/White Wipes where crew must NOT touch.
- Perform Microbe-I operations according to ODFs without instructor’s assistance.
Microbe-I Overview
Microbe-I Operations Overview
Key points during Microbe-I operations
Microbe-I Operations
3 Training Purposes OnlyJEM MICROBE-I 31407JMU-081192 (Ver. 1.2)
Lesson Outline
Contents:
- Microbe-I Overview
- Microbe-I Operations Flow
- Key Points during Microbe-I Operations
- Appendix
Page:
4
5
6
7
4 Training Purposes OnlyJEM MICROBE-I 31407JMU-081192 (Ver. 1.2)
Microbial Detection Sheet Yeast and Mold White Wipe in White Tube Blue Wipe in Blue Tube Photos of Microbial Detection Sheet Yeast and Mold and sampling locations
The purpose of this experiment is to monitor microbes in Kibo which may affect the health of crew members.
Microbe-I Overview
Microbe-I Science Objective
Onboard Outcomes from Microbe-I Experiment
Microbial Detection Sheet Yeast and Mold White Wipe and White Tube(for freezing)
Blue Wipe and Blue Tube(for refrigeration)
5 Training Purposes OnlyJEM MICROBE-I 31407JMU-081192 (Ver. 1.2)
Microbial Detection Sheet Sampling
Microbial Detection Sheet Preparation
Microbial Detection Sheet Sampling
Photographing Microbial Detection Sheet
Microbial Detection Sheet Incubation (7 days)
Blue/White Wipe Sampling
Blue/White Wipe Sampling
Blue/White Wipe MELFI Insertion
Microbe-I Operations Flow
:Crew operations
LEGEND:
Microbe-I Operations Flow
Microbial Detection Sheet MELFI Insertion
Photographing Sampling Location
6 Training Purposes OnlyJEM MICROBE-I 31407JMU-081192 (Ver. 1.2)
Key Points during Microbe-I Operations
Category Equipment Key Points
Crew Safety
Bio Contamination due to leakage of Microbial Detection Sheet culture media
Microbial Detection Sheet
- After Microbial Detection Sheet is used, cover film must be applied.
- Microbial Detection Sheet must be contained in Ziplock bag.
(2-level containment: cover film and ziplock bag)
BZK Wipes - Use BZK Wipe to clean residual Microbial Detection Sheet culture media.
- Discard BZK Wipe into two Ziplock bags. (2-level containment)
Time Critical Operation N/A N/A
Dos and Don’ts Gloves - Do NOT contaminate gloves by bare skin or mucosa membrane throughout sampling.
Microbial Detection Sheet
- Do NOT touch non-woven fabric or inner side of cover film where non-woven fabric will contact to prevent contamination.
Blue/White Wipe
- Do NOT touch Blue/White Wipe except cap to prevent contamination.
Difficulty in Ops N/A N/A
Possible Mis-Ops N/A N/ACAUTION: Crew safety may be changed in future.
(Final Payload Safety Review Panel has not been held yet.)