trane programmable thermostat setup instructions · pdf filetitle: trane programmable...

2
3 March 2012 © 2012Trane. X39641168-01B All rights reserved. 1 2 Setup Instructions Trane ProgrammableThermostat X13511537-01/BAYSTAT150A/THT02774 SAFETY WARNING Only qualified personnel should install and service the equipment.The installation, starting up, and servicing of heating, ventilating, and air- conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all precautions in the literature and on the tags, stickers, and labels that are attached to the equipment. More information: https://www.trane.com/stat Time Setup To change the current time: 1. From the Home screen, press , , , , , . 2. Press , , or to scroll between hours and minutes. AM PM Hours Minutes 1. Press to increase or to decrease the hour or minute. PM PM AM PM Changing Hours Changing Minutes 1. Press and hold for 2 seconds or wait 10 seconds to Save and Exit. System Mode Setup To set the system mode: 1. From the operating screen, press , .The current mode flashes. 2. Press or to select a mode. Emergency Heat Cool Auto H/C Off Heat OFF Note: Not all system choices may be available depending on the system configuration 0130. 3. Press and hold for 2 seconds or wait 10 seconds to Save and Exit. Fan Mode The fan mode is displayed only on systems configured with the fan enabled. For systems configured with a fan, the fan setting is shown on the display. In addition, the setting also appears on the display when pressing , , from the Home screen. The fan mode setting can be overridden by pressing or when the fan mode flashes. Press and hold for 2 seconds or wait 10 seconds to Save and Exit. Refer to the section, “Timed Override (TOV)”. On Mode: Arrows Flash Auto Mode: Auto Flashes Important: When this thermostat is configured in programmable mode (0140=1), then changing the Fan Mode from the Home screen puts the thermostat into Timed Override (TOV) and is only temporary.The fan goes back to the schedule setting after theTOV timer expires. Timed Override (TOV) A timed override can be used to temporarily change the heating setpoint, cooling setpoint, fan mode, and/or occupancy setting from the programmed schedule.The override can be set for up to 99 days and up to 23 hours. To enter a timed override: 1. From the operating screen, press or 2 times.The thermostat enters timed override mode with the hourglass and setpoint flashing. 2. Press or press or to move from either left or right through the selections. Some of the selections may not be available depending on the system type. Cooling Setpoint Occupancy Setting Hours Heating Setpoint Fan Setting HOURS (Days)* DAYS 3. Press or to change the value of the currently active (flashing) selections. Repeat steps 2 and 3 for the desired settings. Note: To reach the DAYS setting, the user must press from the hours setting. 4. Press and hold for 2 seconds or wait 10 seconds to Save and Exit. Note: The thermostat will return to the scheduled operation when: • the override time expires, or • pressing and holding an for 2 seconds. Important: When in timed override mode, if the system selection is changed (EmHeat, Heat, Cool, Auto, OFF), this change will take the thermostat out ofTOV mode. Important: Whenever the thermostat is inTOV mode, a solid hour glass ( ) indicator displays at the bottom of the screen.

Upload: vuthu

Post on 06-Mar-2018

301 views

Category:

Documents


10 download

TRANSCRIPT

Page 1: Trane Programmable Thermostat Setup Instructions · PDF fileTitle: Trane Programmable Thermostat Setup Instructions Author: Larrieu Subject: How to setup programmable thermostats

Setup Instructions

Trane ProgrammableThermostat

X13511537-01/BAYSTAT150A/THT02774

SAFETY WARNING

Only qualified personnel should install and service the equipment.Theinstallation, starting up, and servicing of heating, ventilating, and air-conditioning equipment can be hazardous and requires specificknowledge and training. Improperly installed, adjusted or alteredequipment by an unqualified person could result in death or seriousinjury.When working on the equipment, observe all precautions in theliterature and on the tags, stickers, and labels that are attached to theequipment.

More information:https://www.trane.com/stat

March 2012 © 2012Trane. X39641168-01BAll rights reserved.

1Time Setup

To change the current time:1. From the Home screen, press , , , , , .

2. Press , , or to scroll between hours and minutes.

AMPM

Hours Minutes

1. Press to increase or to decrease the hour or minute.

PM PMAM

PM

Changing Hours Changing Minutes

1. Press and hold for 2 seconds or wait 10 seconds to Save and Exit.

System Mode Setup

To set the system mode:1. From the operating screen, press , .The current mode flashes.

2. Press or to select a mode.

EmergencyHeat

Cool Auto H/C OffHeat

OFF

Note: Not all system choices may be available depending on thesystem configuration 0130.

3. Press and hold for 2 seconds or wait 10 seconds to Save and Exit.

2Fan Mode

The fan mode is displayed only on systems configured with the fanenabled.For systems configured with a fan, the fan setting is shown on thedisplay. In addition, the setting also appears on the display whenpressing , , from the Home screen.The fan mode setting can be overridden by pressing or when thefan mode flashes. Press and hold for 2 seconds or wait 10 seconds toSave and Exit. Refer to the section, “Timed Override (TOV)”.

On Mode:Arrows Flash

Auto Mode:Auto Flashes

� Important: When this thermostat is configured inprogrammable mode (0140=1), then changing the FanMode from the Home screen puts the thermostat intoTimed Override (TOV) and is only temporary.The fangoes back to the schedule setting after theTOV timerexpires.

3Timed Override (TOV)

A timed override can be used to temporarily change the heating setpoint,cooling setpoint, fan mode, and/or occupancy setting from theprogrammed schedule.The override can be set for up to 99 days and upto 23 hours.To enter a timed override:1. From the operating screen, press or 2 times.The thermostat

enters timed override mode with the hourglass and setpointflashing.

2. Press or press or to move from either left or right throughthe selections. Some of the selections may not be availabledepending on the system type.

CoolingSetpoint

OccupancySetting

Hours HeatingSetpoint

FanSetting

HOURS

(Days)*DAYS

3. Press or to change the value of the currently active (flashing)selections. Repeat steps 2 and 3 for the desired settings.Note:To reach the DAYS setting, the user must press from thehours setting.

4. Press and hold for 2 seconds or wait 10 seconds to Save and Exit.

Note:The thermostat will return to the scheduled operation when:• the override time expires, or• pressing and holding an for 2 seconds.

� Important: When in timed override mode, if the systemselection is changed (EmHeat, Heat, Cool, Auto, OFF), thischange will take the thermostat out ofTOV mode.

Important: Whenever the thermostat is inTOV mode, asolid hour glass ( ) indicator displays at the bottom of thescreen.

Page 2: Trane Programmable Thermostat Setup Instructions · PDF fileTitle: Trane Programmable Thermostat Setup Instructions Author: Larrieu Subject: How to setup programmable thermostats

Trane optimizes the performance of homes and buildings around the world. A business ofIngersoll Rand, the leader in creating and sustaining safe, comfortable and energy efficientenvironments, Trane offers a broad portfolio of advanced controls and HVAC systems,comprehensive building services, and parts. For more information, visit www.IRCO.com.

Trane has a policy of continuous product and product data improvement and reserves the rightto change design and specifications without notice.

© 2012Trane. All rights reserved.X39641168-01B 13 Mar 2012Supersedes x39641168-01A 03 Dec

We are committed to usingenvironmentally consciousprint practices that reduce

4Create or Edit a Schedule

To create or edit a schedule:

1. Press , , , , .

Note: Each button shown above must be pressed within 10 secondsof the previous button. Once the user is in Schedule Change Mode,each button must be pressed within 45 seconds of the previous buttonin order to stay in Schedule Change Mode.

2. Press or to select the day(s) andto continue.

Mo Tu We Th Fr Sa Su

AM

We

AM

We

AM

Auto On

3. Press or to select the period andto continue.

4. Press or to change the StartTimeand to continue.

5. Press or to change the HeatingSetpoint and to continue.

6. Press or to change the CoolingSetpoint and to continue.

7. Press or to select the Fan Settingand to continue.

8. Repeat steps 2 through 7 for each day(see step 2) and period (see step 3).Toexit Schedule Change Mode, wait 45seconds or press and hold for 2seconds to Save and Exit.

Possible Scheduling Configurations (configuration option 0233):

• 1 day [default]; MoTuWeThFrSaSu (all days share a schedule).

• 5+1+1 days; MoTuWeThFr Sa Su (Monday through Friday sharea schedule, Saturday and Sunday are each separate schedules).

• 5+2 days; MoTuWeThFr SaSu (Monday through Friday share aschedule, Saturday and Sunday share a schedule).

• 7 days; Mo Tu We Th Fr Sa Su (Each day has a separateschedule).

Note: Use the worksheet on the right for planning or recording schedulesettings. Default settings are ENERGY STAR® compliant.

5

8:00 am

6:00 am 70 °F (21.0 °C)

62 °F (16.5 °C)

70 °F (21.0 °C)

62 °F (16.5 °C)

78 °F (25.5 °C)

85 °F (29.5 °C)

78 °F (25.5 °C)

82 °F (28.0 °C)10:00 pm

6:00 pm

Mo

Tu

We

Th

Fr

Sa

Su

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

°°:

4-P

eri

od

defa

ult

s2-P

eri

od

defa

ult

s

70 °F (21.0 °C)

55 °F (13.0 °C)

78 °F (25.5 °C)

85 °F (29.5 °C)10:00 pm

8:00 am

Morning Day Evening Night Time Heat Cool Fan ON

Legend of Symbols

2009 waste.