Triple Monitor Counterbalance Desk MountInstruction Manual

If you have any questions , please contact us.

MU0006 75x75100x100

(1~8kg)x3(2.2~17.6lbs)x3

27"

V9.0

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.

Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or

weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

NOTE: Not all hardware included will be used.

DO NOT EXCEED WEIGHT CAPACITY.

WARNING!

PACKAGE CONTENTS

(2.2~17.6lbs)x3(1~8kg)x3

A (x1)Arm

B (x1)Clamp

All are included in B

BracketB1

Clip PlateB2

BoltsB5

Bottom PlateB3

Bolt YB4

C (x1)Decorative cover

G (x1)Wire clip

K (x1)Grommet Base

H (x3)Bolt

I (x3)Bolt

J (x1)Support Plate

L(x1)4mm Allen Key

M(x1)5mm Allen Key

N(x1)6mm Allen Key

E(x1)Middle Head

F(x1)Pole

D (x3)VESA Plate

M-E (x12)D6 Washer

01

M-C (x12)M6x12

M-F (x12)M-B (x12)M4x16

M-D (x12)M6x16

M-A (x12)M4x12

Loosen Bolts (B5) by using 6mm Allen Key (N), then lift clip plate (B2), bottom plate (B3), and bolt Y (B4) a little to release them from bracket (B1).

Attach clip plate(B2), bottom plate(B3), bolt Y(B4), to bracket (B1) using bolts (B5) and 6mm allen key (N). Mount according to the thickness of desktop.

Mount bracket (B1) to pole(F) using bolts (I). Tighten using 4mm allen key(L).

ASSEMBLY STEPSSTEP 1: Clamp Installation OR Grommet Base Installation

02

35

-80

mm

N N

10

-45

mm

F

B1

B5

I

L

B1 B1

B3B4

B3

B4

B5

B5

B2 B2

N

OPTION A: Clamp Installation

B4

B

C

N

B1

B2

B3

B4

Decorative cover (C) to pole(F) and secure stand to desktop by tightening clamp (B). Tighten bolt Y (B4) or by using 6mm allen key (N).

F

OPTION B: Grommet Base Installation Use 6mm allen key(N) to detach the bolt(B5), clip plate(B2),bottom plate(B3) and bolt Y(B4) from clamp(B).

STEP 1: (Continued)

03

Install the grommet base plate(K) to the pole (F) using bolt (I). Install pole(F) with bolt Y(B4) and support plate(J). Tighten bolt Y (B4) or by using 6mm allen key (N).

N

B1B2

B3

B4

B5

B4

K

B4

10-80mm

I

F

J

N

Install the middle head(E), wire clip(G) and swivel arm(A) to the pole.Fasten the bolt with supplied 6mm Allen key (N)

STEP 2 : Arm Installation

04

N

G

E

A

Just tighten the bolt, do not over tighten it in case the cast aluminum part could be damaged.

NOTE: Hand tighten screws to avoid over tightening.

STEP 3 : Attach Monitor

05

M-AM-C

M-E

N

M-BM-D

M-E

M-F

N

OPTION B: Curved Back Monitor

Attach the VESA plate (D) to back of monitor and secure with screws (M-B) or (M-D) with washers (M-E)and washers(M-F)using 6 mm Allen Key (N). Avoid excessive tightening screws damage the monitor.

OPTION A: Flat Back Monitor

Attach the VESA plate (D) to back of monitor and secure with screws(M-A)or(M-C) with washers(M-E) using 6 mm Allen Key (N). Avoid excessive tightening screws damage the monitor.

D

D

STEP 4 : Hang Monitor

06

H

Refer to below illustrations to adjust tilting angle of your monitor.

Tilts down

N

Slide the monitors onto the head of swivel arm.Install the security bolt (H). Make sure the security bolt is installed before you rotate the monitor.

Note: 1. Loosen the tilting bolt.2. Adjust monitor to your desired tilting angle.3. Retighten the tilting bolt to

Important Notice:The gas spring tension is pre-set to the weakest level by default, please hold your monitor by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas spring arm falls down greatly.

STEP 5 : Adjust Tension

tension in gas spring arm (A) using 6 mm Allen Key (N).

07

Note1:Be sure to keep the arm in horizontal position during adjustment.

Falls down

After being attached to the arm, the monitor falls down and can not stay at the desired height by itself.

Turn counter-clockwise(“+”direction) to increase gas spring tension until the monitor can stay at the desired height by itself.

After being attached to the arm, the monitor rises up and can not stay at the desired height by itself.

Turn clockwise(“-”direction) to reduce gas spring tension until the monitor can stay at the desired height by itself.

Rises up

A

CAUTION

Circles

Monitor Weight

(AT LEAST)

As for how many circles the screw should be turned, the table below is for reference.Note2:

1kg 2kg 3kg 4kg 5kg 6kg 7kg 8kg

min 1 2 5 7 10 13 15

STEP 6 : Cable Management

Remove bottom plastic covers from gas spring arm (A) .Run cables from monitor through bottom of gas spring arm (A). Reattach plastic covers as shown in diagram.

08

A

Adjust as Desired

09

M

±180°

±90°±90°

+35°

-35°

MN

DESK DESK

Pay attention while clamp install !

Note: The total length of 3 monitors after arrayed can not be longer than 183cm.

≤183cm

If necessary, refer to above illustrationsto adjust the level of tightness of the arms.

+- M

10

Product Dimensions

2.9”3.9“4.48“

2.9” 3.9“ 4.48“

8.1“-10.3”

7.9“7.9“

1.7”

2.67”

5.7"

16.5”

0.39"-3.15"

+35°

-35°

±180°

±180°

±180°

±90°

±90°

4.5“-27.8“

11.5”

0.39"-3.15"

STEP 6

CAUTION AND MAINTENANCE:• Never allow children to climb, stand, hang, or play on any part of monitor or stand.• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury. • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

If you have any questions, please contact us.