tube & tube fittings product guide - s&t...
TRANSCRIPT
PRO
DU
CT
GU
IDE
TU
BE &
TU
BE F
ITTI
NG
S
TUBE & TUBE FITTINGS PRODUCT GUIDE
STA
INLE
SS S
TEEL
MA
Y 2
014
S&T STAINLESS LTD
Head Office 7 Bruce Roderick Drive
East Tamaki, Auckland 2013
P: +64 9 271 1780
P O Box 58880, Botany, Auckland 2163
F: +64 9 271 1970
Auckland 7 Bruce Roderick Drive
East Tamaki, Auckland 2013
P: +64 9 271 1781
P O Box 58880, Botany, Auckland 2163
F: +64 9 271 1799
Mt Maunganui 18 MacDonald Street
Mt Maunganui South 3116
P: +64 7 574 0095
P O Box 4158, Mt Maunganui South 3149
F: +64 7 574 0096
Hamilton 27 Ellis Street
Frankton, Hamilton 3204
P: +64 7 847 8456
P O Box 1133, Waikato Mail Centre, Hamilton 3240
F: +64 7 847 0354
Hastings 117 Elwood Rd
Hastings 4172
P: +64 6 876 3360
P O Box 14043, Mayfair, Hastings 4159
F: +64 6 876 3411
New Plymouth Cnr Connett Rd & Mustang Dr
Bell Block, New Plymouth 4373
P: +64 6 755 3971
P O Box 3094, Fitzroy, New Plymouth 4341
F: +64 6 755 3974
Wellington 141 Hutt Park Road
Gracefield, Lower Hutt 5010
P: +64 4 568 5014
P O Box 38065, Wgtn Mail Centre, Lower Hutt 5045
F: +64 4 568 6367
Nelson 4c Akersten Street
Port Nelson, Nelson 7010
P: +64 3 548 0603
P O Box 413, Nelson 7040
F: +64 3 548 0588
Christchurch 200 Maces Road
Bromley, Christchurch 8062
P: +64 3 381 1994
P O Box 570, Christchurch 8140
F: +64 3 381 0606
Toll free 0800 426 787 Website www.stainless.steelandtube.co.nz
CONTENTS – SECTION C
TUBES / TUBE FITTINGS
Hygienic (Dairy) Tube C2
Structural (Handrail) Tube C3
RigiTube C3
Square Tube (SHS) C4
Rectangular Tube (RHS) C5
Bends C6
Tube Bends C7
Tube Reducers C8
Welding Tees C9
Reducing Tees C9
Tri-Clamp Fittings C10
CIP (Clean in Place) Dairy Fittings C11
Technical Data C12
Tube Hangers/Brackets C13
Handrail Accessories C14
Expansion Flanges C15
C2 STAINLESS STEEL CATALOGUE
STAINLESS STEEL ROUND DAIRY TUBE
Manufactured to ASTM A269/A270, AS1528 (Food/Hygienic Applications)
SIZE (O.D.) inch
SIZE (O.D.) mm
WALL THICKNESS
mm
THEORETICAL WEIGHT kgs / mtr
T304 T316 2205
POL POL AW
1/4” 6.3 0.9 0.122 •
5/16” 7.9 0.9 0.158 •
3/8” 9.5 0.9 0.194 •
3/8” 9.5 1.2 0.250 • •
1/2” 12.7 0.9 0.276 •
1/2” 12.7 1.2 0.346 •
1/2” 12.7 1.6 0.445 • •
5/8” 15.9 0.9 0.341 •
5/8” 15.9 1.2 0.445 •
5/8” 15.8 1.6 0.577 • •
3/4" 19.1 0.9 0.408 •
3/4" 19.1 1.2 0.542 •
3/4" 19.1 1.6 0.697 • • **
7/8” 22.2 0.9 0.482 •
7/8” 22.2 1.2 0.638 •
7/8” 22.2 1.6 0.825 •
1” 25.4 0.9 0.552 •
1” 25.4 1.2 0.735 • •
1” 25.4 1.6 0.965 • • **
1 1/8” 28.6 1.6 1.066 •
1 1/4” 31.8 0.9 0.697 •
1 1/4” 31.8 1.2 0.920 •
1 1/4” 31.8 1.6 1.210 • •
1 1/2" 38.1 0.9 0.836 •
1 1/2" 38.1 1.2 1.106 •
1 1/2" 38.1 1.6 1.458 • • **
1 3/4" 44.5 1.6 1.719 • •
2” 50.8 1.2 1.496 •
2” 50.8 1.6 2.000 • • **
2” 50.8 2.0 2.447 •
2 1/2" 63.5 1.2 1.872 •
2 1/2" 63.5 1.6 2.480 • •
2 1/2" 63.5 2.0 3.730 **
3” 76.2 1.6 2.984 • •
3” 76.2 2.0 3.730 • **
3 1/2" 88.9 1.6 3.680 •
4” 101.6 1.6 4.005 • •
4” 101.6 2.0 4.995 • **
5” 127.0 1.6 4.970 • •
6” 152.4 1.6 5.910 • •
6” 152.4 2.0 8.333 • •
– ** 2205 tube is sourced to order, and conforms to ASTM A789. – Other sizes and grades may be available on request. – Standard Length - 6.0 metres. – "L" – Low Carbon Grade can be supplied on request in both T304 and T316 Round or Square Tube. – All tubes over 31.8mm diameter have a cold worked weld bead to ensure a hygienic internal surface. – Finish: AW - As Welded Only the welds are linished.
POL - Buff Polished External surface is buff polished to a 320 grit finish. – Other finishes available on request. – Annealed tube can be sourced to order.
C3
STAINLESS STEEL ROUND STRUCTURAL TUBE
Manufactured to ASTM A554
SIZE (O.D.) inch
SIZE (O.D.) mm
WALL THICKNESS
mm
THEORETICAL WEIGHT kgs / mtr
T304 T316
320 600 320 600
3/8” 9.5 1.2 0.250 •
1/2" 12.7 1.5 0.445 •
5/8” 15.9 1.2 0.445 •
5/8” 15.9 1.5 0.577 • •
3/4" 19.1 1.2 0.542 •
3/4" 19.1 1.5 0.697 • •
7/8” 22.2 1.2 0.638 •
7/8” 22.2 1.5 0.825 • •
1” 25.4 1.2 0.735 •
1” 25.4 1.5 0.965 • • •
1” 25.4 3.0 1.668 • •
1 1/4" 31.8 1.2 0.920 •
1 1/4" 31.8 1.5 1.210 • • •
1 1/2" 38.1 1.5 1.458 • • •
1 1/2" 38.1 3.0 2.900 • •
1 3/4" 44.5 1.2 1.301 • •
1 3/4" 44.5 1.5 1.719 • • •
2” 50.8 1.5 2.000 • • •
2” 50.8 2.0 2.447 • •
2” 50.8 3.0 3.560 • • •
2 1/2” 63.5 1.5 2.480 • • •
2 1/2" 63.5 3.0 4.505 •
3” 76.2 1.5 2.984 • • •
4” 101.6 1.5 4.005 • • •
5” 127.0 2.0 6.205 •
6” 152.4 2.0 8.333 •
– ASTM A554 tubes are suitable for handrail or structural applications. – ASTM A554 tubes are not suitable for hygienic use, transporting fluids, or use in pressurised pipelines. – Other sizes and grades may be available on request.
– Standard Length - 6.0 metres.
– Other finishes including Mirror or UltraBriteTM Polish available on request.
STAINLESS STEEL RIGITUBE ™
Manufactured to ASTM A554
SIZE (O/D) inch
SIZE (O/D) mm
WALL THICKNESS
mm
T304 RIMEX 7GM PATTERN
1 1/4" 31.8 1.2 •
– Available ex stock in 3 metre and 6 metre lengths only.
– Other sizes, patterns and material grades may be available on request
subject to minimum quantity requirements.
– Handrail brackets suitable for use with RigiTube also available – refer page C14.
C4 STAINLESS STEEL CATALOGUE
STAINLESS STEEL SQUARE TUBE (SHS)
Manufactured to ASTM A554
SIZE (O/D) mm
WALL THICKNESS
THEORETICAL WEIGHT kgs / mtr
T304 T316
POL AW POL AW
12.7 x 12.7 1.2 0.468 •
12.7 x 12.7 1.5 0.585 •
19.1 x 19.1 1.2 0.672 •
19.0 x 19.0 1.5 0.881 • •
25.4 x 25.4 1.2 0.920 •
25.4 x 25.4 1.5 1.210 • •
25.4 x 25.4 2.0 1.610 •
25.4 x 25.4 3.0 2.420 •
30.0 x 30.0 1.5 1.473 •
31.8 x 31.8 1.2 1.118 •
31.8 x 31.8 1.5 1.868 • •
35.0 x 35.0 1.5 1.770 •
38.1 x 38.1 1.2 1.412 •
38.1 x 38.1 1.5 1.868 • •
40.0 x 40.0 2.0 2.560 •
40.0 x 40.0 3.0 3.750 • •
50.0 x 50.0 2.0 3.150 •
50.8 x 50.8 1.5 2.487 • •
50.8 x 50.8 2.0 3.264 • •
50.8 x 50.8 3.0 4.870 • •
50.8 x 50.8 4.0 6.528 •
50.8 x 50.8 5.0 8.120 •
60.0 x 60.0 2.0 3.840 •
60.0 x 60.0 3.0 5.760 • •
75.0 x 75.0 2.0 6.000 •
75.0 x 75.0 3.0 9.000 •
75.0 x 75.0 5.0 12.000 •
80.0 x 80.0 2.0 5.120 •
80.0 x 80.0 3.0 7.680 • •
80.0 x 80.0 5.0 12.800 • •
100.0 x 100.0 3.0 9.600 • •
100.0 x 100.0 4.0 12.800 •
100.0 x 100.0 5.0 16.000 • •
101.6 x 101.6 4.5 15.040 •
150.0 x 150.0 3.0 14.400 •
150.0 x 150.0 4.0 18.300 •
150.0 x 150.0 6.0 27.400 •
152.4 x 152.4 4.5 22.000 •
152.4 x 152.4 6.35 30.800 •
200.0 x 200.0 6.0 36.900 • •
– ASTM A554 tubes are suitable for handrail or structural applications. – ASTM A554 tubes are not suitable for hygienic use, transporting fluids, or use in pressurised pipelines. – Other sizes and grades may be available on request.
– Standard Length - 6.0 metres. – Finish: AW - As Welded Only the welds are linished.
POL - Polished Architectural Finish (180 Grit) – T304
Architectural Finish (320 Grit) – T316
C5
STAINLESS STEEL RECTANGULAR TUBE (RHS)
Manufactured to ASTM A554
SIZE (O/D) mm
WALL THICKNESS
THEORETICAL WEIGHT kgs / mtr
T304 T316
POL AW POL AW
40.0 x 10.0 1.5 0.510 •
40.0 x 20.0 1.5 1.020 •
40.0 x 20.0 2.0 1.360 •
50.0 x 10.0 1.5 0.740 •
50.0 x 25.0 1.5 1.868 • •
50.0 x 25.0 2.0 2.490 •
59.0 x 15.0 2.0 2.370 •
80.0 x 20.0 1.5 2.480 •
80.0 x 40.0 2.0 3.840 • •
80.0 x 40.0 3.0 5.760 • •
80.0 x 40.0 5.0 9.600 • •
100.0 x 50.0 3.0 7.200 • •
100.0 x 50.0 5.0 12.000 • •
101.6 x 50.8 4.5 11.440
150.0 x 100.0 4.0 15.400 •
150.0 x 100.0 6.0 23.400 •
152.4 x 101.6 4.5 18.560
200.0 x 100.0 4.0 18.300 •
200.0 x 100.0 6.0 27.000 •
200.0 x 150.0 4.0 21.600 •
200.0 x 150.0 6.0 32.300 •
– ASTM A554 tubes are suitable for handrail or structural applications. – ASTM A554 tubes are not suitable for hygienic use, transporting fluids, or use in pressurised pipelines. – Other sizes and grades may be available on request.
– Standard Length - 6.0 metres.
– Finish: AW - As Welded Only the welds are linished.
POL – Polished Architectural Finish (180 Grit) – T304
Architectural Finish (320 Grit) – T316
C6 STAINLESS STEEL CATALOGUE
STAINLESS STEEL BENDS
Manufactured to AS1528 (Food/Hygienic Applications)
DIMENSIONS OF 45, 90, 180 BENDS
Table 1 – New Zealand Dimensions
OD SIZE GAUGE R A B
(mm) (inch) (mm) (mm) (mm) (mm)
12.7 1/2 1.2 19.05 44.50 30.00
15.9 5/8 1.2 23.80 57.20 30.00
19.1 3/4 1.2/1.6 28.65 63.50 30.00
25.4 1 1.2/1.6 38.10 66.70 30.00
31.8 1 1/4 1.2/1.6 57.20 88.90 31.80
38.1 1 1/2 1.2/1.6 76.20 111.10 34.90
44.5 1 3/4 1.2/1.6 79.40 117.50 38.10
50.8 2 1.2/1.6 101.60 133.40 31.80
63.5 2 1/2 1.6 114.30 152.40 38.10
76.2 3 1.6 139.70 177.80 38.10
101.6 4 1.6 152.40 182.40 30.00
152.4 6 2.0 228.60 260.40 40.00
NOTE: For 180º bends dimension ‘R’ specified above may vary slightly due to the variation in temper of mill supplied tube. Where dimension ‘R’ is critical, for intended use, please consult S&T Stainless to determine the exact dimension, when ordering.
DIMENSIONS OF 90 SHORT RADIUS
Table 2 – New Zealand Dimensions
NOMINAL OD SIZE
GAUGE R D B
(mm) (inch) (mm) (mm) (mm) (mm)
25.4 1 1.6 38.1 50.08 0.0
31.8 1 1/4 1.6 47.6 76.2 12.7
38.1 1 1/2 1.6 57.2 76.2 0.0
50.8 2 1.6 76.2 101.6 0.0
63.5 2 1/2 1.6 95.3 127.0 0.0
76.2 3 1.6 114.3 152.4 0.0
101.6 4 1.6 152.4 203.2 0.0
90º Short Radius New Zealand Dimensions For dimensions refer to Table 2
90º New Zealand Dimensions For dimensions R, A and B refer Table 1
45º New Zealand Dimensions For dimensions R and B refer Table 1
180º New Zealand Dimensions For dimensions R, A and B refer Table 1
C7
STAINLESS STEEL TUBE BENDS
New Zealand Dimensions Refer to C6
Dimensions refer to Page C6
L = Type ‘L’ – Low Carbon Standard Bends
** 2205 fittings are sourced to order.
For larger diameter elbows to suit Spiral Welded Pipe – Refer to Section D
OD WALL
THICKNESS
90° WELD BENDS
90° SHORT RADIUS BENDS
45° LONGLEG
BENDS
90° LONGLEG
BENDS
45° WELD BENDS
180° WELD BENDS
304 316 2205 304 316 304 304 304 316 304 316
12.7 1.2 • •
12.7 1.6 •
15.9 1.2 •
15.9 1.6 •
19.1 1.2 • •
19.1 1.6 • • ** • •
25.4 1.2 • • • •
25.4 1.6 • • ** • • • • • •
31.8 1.2 • • • • •
31.8 1.6 • • • • • • •
38.1 1.2 • • • • •
38.1 1.6 • • ** • • • • • •
44.5 1.6 • • • • •
50.8 1.2 • • • • •
50.8 1.6 • • ** • • • • • •
63.5 1.2 • •
63.5 1.6 • • • • • • •
63.5 2.0 **
76.2 1.6 • • • • • • • • •
76.2 2.0 **
101.6 1.6 • • • • • • • •
101.6 2.0 **
127.0 2.0 •L •L
152.4 2.0 •L •L •L •L
203.2 2.0 •L •L
C8 STAINLESS STEEL CATALOGUE
STAINLESS STEEL TUBE REDUCERS
SIZE mm
CONCENTRIC ECCENTRIC
304 EXT. LEG
316 2205 316
19.1 – 12.7 x 1.6 •
25.4 – 12.7 x 1.6 •
25.4 – 19.1 x 1.6 • •
31.8 – 25.4 x 1.6 • •
38.1 – 19.1 x 1.6
38.1 – 25.4 x 1.6 • • ** •
38.1 – 31.8 x 1.6 • • •
50.8 – 25.4 x 1.6 • ** •
50.8 – 31.8 x 1.6 • •
50.8 – 38.1 x 1.6 • • ** •
63.5 – 25.4 x 1.6 • •
63.5 – 31.8 x 1.6 •
63.5 – 38.1 x 1.6 • •
63.5 – 50.8 x 1.6 • • ** •
76.2 – 25.4 x 1.6 • •
76.2 – 38.1 x 1.6 • •
76.2 – 50.8 x 1.6 • ** •
76.2 – 63.5 x 1.6 • ** •
101.6 – 25.4 x 1.6 •
101.6 – 38.1 x 1.6 •
101.6 – 50.8 x 1.6 • •
101.6 – 63.5 x 1.6 • •
101.6 – 76.2 x 1.6 • ** •
127.0 – 76.2 x 1.6 • •
127.0 – 101.6 x 1.6 • •
152.4 – 50.8 x 1.6 •
152.4 – 63.5 x 1.6 •
152.4 – 76.2 x 1.6 •
152.4 – 101.6 x 1.6 • ** •
152.4 – 127.0 x 1.6 • •
203.2 – 152.4 x 1.6 •
** 2205 fittings are sourced to order.
C9
STAINLESS STEEL WELDING TEES
SIZE mm
STANDARD TEES SWEPT TEES
304 316 316
12.7 x 1.6 • •
15.9 x 1.6 •
19.1 x 1.6 • •
25.4 x 1.6 • • •
31.8 x 1.6 • • •
38.1 x 1.6 • • •
50.8 x 1.6 • • •
63.5 x 1.6 • • •
76.2 x 1.6 • • •
101.6 x 1.6 • • •
152.4 x 1.6 •
** 2205 fittings are sourced to order.
OTHER SIZES AVAILABLE ON REQUEST CROSS AND “Y” PIECE FITTINGS ALSO AVAILABLE
STAINLESS STEEL REDUCING TEES
SIZE mm
AS DRAWN LONG LEG TEE
316 2205
25.4 x 1.6 • ** 25.4 x 1.6
31.8 x 1.6 • 31.8 x 1.6
38.0 x 1.6 • ** 38.0 x 1.6
50.8 x 1.6 • ** 50.8 x 1.6
63.5 x 1.6 • ** 63.5 x 1.6
76.2 x 1.6 • ** 76.2 x 1.6
101.6 x 1.6 • ** 101.6 x 1.6
127.0 x 2.0 • 127.0 x 2.0
152.4 x 2.0 • 152.4 x 2.0
203.2 x 2.0 • 203.2 x 2.0
SIZE mm
AS DRAWN
316
38.1 – 25.4 •
50.8 – 25.4 •
50.8 – 38.1 •
63.5 – 25.4 •
63.5 – 38.1 •
63.5 – 50.8 •
76.2 – 25.4 •
76.2– 38.1 •
76.2 – 50.8 •
76.2 – 63.5 •
101.6 – 25.4 •
101.6 – 38.1 •
101.6 – 50.8 •
101.6 – 63.5 •
101.6 – 76.2 •
152.4 – 76.2 •
152.4 – 101.6 •
C10 STAINLESS STEEL CATALOGUE
STAINLESS STEEL TRI-CLAMP FITTINGS
HEAVY DUTY CLAMP (13 LAH)
SIZE (OD) mm
12.7 19.1 25.4 31.8 38.1 50.8 63.5 76.2 101.6 152.4
A 28.5 28.2 53.6 53.6 53.6 67.0 80.6 94.0 122.0 169.6
BUTT WELDING FERRULE (IDFA)
SIZE (OD) mm
12.7 19.1 25.4 31.8 38.1 50.8 63.5 76.2 101.6 152.4
A 21.5 21.5 21.5 21.5 21.5 21.5 21.5 21.5 38.1
B 12.7 19.1 25.4 38.1 50.8 63.5 76.2 101.6 152.4
RECESSLESS (EXPANDING) FERRULE (14 RMP)
SIZE (OD) mm
12.7 19.1 25.4 31.8 38.1 50.8 63.5 76.2 101.6 152.4
A 28.6 28.6 33.3 34.9 36.5 38.1
B 31.9 38.2 50.9 63.6 76.3 101.7
Dimension B = Tube OD + 0.1mm
SOLID END CAP (16 AMP)
SIZE (OD) mm
12.7 19.1 25.4 31.8 38.1 50.8 63.5 76.2 101.6 152.4
A 5.0 5.0 6.4 6.4 6.4 6.4 6.4 7.9 11.1
B 25.2 25.2 50.4 50.4 63.9 77.4 90.9 118.9 166.9
EPDM SEAL (40A)
SIZE (OD) mm
12.7 19.1 25.4 31.8 38.1 50.8 63.5 76.1 101.6 152.4
A 21.8 21.8 50.4 50.4 50.4 63.9 77.4 90.9 118.9 166.9
B 9.5 15.8 22.2 28.5 34.9 47.5 60.2 72.9 97.4 146.9
C 4.3 4.3 5.15 5.15 5.15 5.15 5.15 5.15 5.15 5.15
C11
STAINLESS STEEL DAIRY FITTINGS (CIP UNIONS)
Manufactured to BS1804, 1134 and AS1528
mm HEX NUT
ROUND NUT
MALE PART
C.I.P. WELD LINER
C.I.P. SEAL
25.4 • • • • •
38.0 • • • • •
51.0 • • • • •
63.5 • • • • •
76.1 • • • • •
101.6 • • • • •
127.0 • •
152.4 • • • •
mm BLANK TEFLON
SEAL “O”
RING HEX
SPANNER
25.4 • • • •
38.0 • • • •
51.0 • • • •
63.5 • • • •
76.1 • • • •
101.6 • • • •
127.0 • 152.4 • • •
ROUND NUT “C” SPANNER 25mm-101mm
C12 STAINLESS STEEL CATALOGUE
TECHNICAL DATA
HEXAGON NUT
ROUND NUT
WELDING LINER
CIP SEAL
WELDING MALE PART
CIP BLANK
RJT O-RING
HEX NUT STAINLESS
STEEL TYPE 304
ROUND NUT STAINLESS
STEEL TYPE 304
WELDING LINER STAINLESS
STEEL TYPE 316
C.I.P SEAL NITRILE RUBBER
MALE PART STAINLESS
STEEL TYPE 316
RJT SEAL NITRILE RUBBER “O” RING
TUBE SIZE
A B A B A B A B A B A
25.4 58.00 34.00 56.80 34.00 41.27 22.00 39.67 22.90 45.72 22.00 39.67
38.1 75.00 46.60 73.80 46.60 53.90 34.84 52.40 34.84 58.12 34.84 52.40
50.8 92.00 59.40 85.60 59.40 66.67 47.60 65.10 46.76 72.42 47.60 65.10
63.5 108.00 73.20 97.10 73.20 79.50 60.05 77.80 59.40 85.12 60.05 77.80
76.2 121.00 84.40 111.50 84.40 92.07 73.00 90.50 72.10 97.82 73.00 90.50
101.6 152.00 110.10 139.00 110.10 117.47 98.40 115.90 97.50 123.20 98.40 115.90
127.0 172.00 137.00 142.00 123.00 140.00 123.00 147.00 123.00
152.4 200.00 162.80 167.50 147.50 173.20 147.50 173.20
C13
STAINLESS STEEL TUBE HANGERS
SIZE mm
PLAIN BOSS 5/8*
SLIDE N.B.
PLAIN N.B.
BOSS * MUNSON
RING M
BRACKET
12.7 • •
19.1 • • •
25.4 • • • • • • •
31.8 • • • • •
38.1 • • • • • • •
50.8 • • • • • • •
63.5 • • • • • •
76.2 • • • • • •
101.6 • • • • • •
127.0 • • •
152.4 • • • •
203.2 • •
254.0 •
*Can also be supplied with M10 + M12 threaded boss
DELIVERY LINE HANGER BRACKET
5/8” BOSS WALLMOUNT BRACKET
AND M10 or M12 ADAPTOR
BOSLOK WALL BRACKET 5/8” or M10 Boss
C14 STAINLESS STEEL CATALOGUE
STAINLESS STEEL HANDRAIL ACCESSORIES
HANDRAIL BRACKETS
– Handrail brackets available with ½” stems, made from T304 stainless steel.
Available in T316 to order.
– Available as complete units or as components.
– Handrail brackets with a BA finish cover plate to hide fixings are also available.
– Saddles suit 38.1, 44.5, or 50.8mm OD stainless steel tube (riveted or welded), or with timber rails (woodscrews).
END CAPS – Weldable Shallow and Deep Domed Pressed
End Caps are available for 25.4 – 203.2mm OD tube. Ex stock in T316 only.
– Push-fit End Caps are available from 19.0 – 50.8mm, to order.
HANDRAIL BRACKET BASE PLATE BLANKS
– 70mm diameter base
RIGITUBE HANDRAIL BRACKETS
Standard Size: 31.80 OD x 1.20mm WT
Material: T304 Stainless Steel
Configurations: Refer Images and listings below
End Bracket MIHBRTE 45° Cnr Bracket – Vertical MIHBRTCV45
Mid Bracket MIHBRTM 90° Cnr Bracket – Vertical MIHBRTCV90
Wall / Floor Bracket MIHBRTWF 90° Cnr Bracket – Horizontal MIHBRTCH90
C15
EXPANSION FLANGES
A purpose designed seal for wall, floor and ceiling penetrations of process piping in food and beverage plants or any applications where a waterproof hygienic seal is required.
Design allows for lineal expansion and contraction of pipework whilst maintaining an intrinsic seal to prevent ingress or water etc. to penetrated material. (See detail 1).
The flange can also be adapted to accommodate Steam Pipe or Non-Standard tube diameters by adding a Teflon or heat resistant liner. (See detail 2).
Detail 1 Detail 2
STANDARD SIZES (DIMENSIONS mm)
TUBE O.D.
A B C D
19.1 21.0 53 70 86
25.4 27.4 53 70 86
31.8 33.8 85 103 118
38.1 40.0 85 103 118
50.8 53.0 85 103 118
63.5 65.5 118 130 140
76.2 78.1 118 130 140
101.6 103.6 140 158 180
127.0 119.0 216 198 216
152.4 140.0 216 198 216
NEW ZEALAND PATENT No: 226079