tubi & spirali - rubete.pt · i controlli effettuati lungo la filiera produttiva a partire...
TRANSCRIPT
Catalogo Generale I General Catalogue
TUBI & SPIRALIPER ARIA COMPRESSA
TUBES & COILS FOR COMPRESSED AIR
2011
ul. Hangarowa 8, 70-767 Szczecin tel. : +48 +91 4640 641 fax : +48 +91 4627 359
www.phu-nova.eue-mail: [email protected]
2
UN’AZIENDA “MADE IN ITALY”A “MADE IN ITALY” COMPANY
Castello Italia si trova nel cuore della pianura padana, in provincia di Cremona; questa posizione strategica ci consente di essere al centro della zona più produttiva del Nord Italia e vicini alle grandi vie di comunicazione ed ai maggiori aeroporti italiani (Milano, Bergamo e Verona). I nostri stabilimenti distano, infatti, circa 60 minuti da Milano e Verona, 40 minuti da Bergamo, 30 minuti da Brescia e 25 minuti da Piacenza.
Castello Italia is located in the heart of Cremona province. This is a strategic location right in the center of the most industrial area in Italy, close to all means of transporta-tion including the biggest Italian airports (Milan, Berga-mo and Verona). Our plant is only 60 minutes away from Milan and Verona, 40 minutes away from Bergamo, 30 minutes away from Brescia and 25 minutes away from Piacenza.
COME RAGGIUNGERCI:
In Auto: Autostrada A21 Uscita di Cremona direzione Bergamo; Autostrada A21 Uscita di Pontevico direzione Soresina-Casalbuttano.
In Aereo: 140 km da Milano Malpensa; 70 km da Milano Linate; 60 km da Milano Orio al Serio (Bergamo); 100 km da Verona; 40 km da Montichiari; 50 km da Parma.
In Treno: Stazione di Casalbuttano (linea Cremona-Ber-gamo).
DIRECTIONS:
By Car: Highway A21, exit Cremona and then follow di-rection to Bergamo; Highway A21, exit Pontevico and then follow Soresina-Casalbuttano.
By Plane: Possible airports: Milano Malpensa and 140 km drive; Milano Linate and 70 km drive; Milano Orio al Serio and 60 km drive; Verona and 100km drive; Monti-chiari and 40km drive; Parma and 50 km drive.
By Train: Casalbuttano station (Cremona-Bergamo line).
Stabilimento/PlantVia Anelli 52
I - 26020 • Casalmorano (CR) • ItalyPh. +39 0374 74135Fax +39 0374 74261
CASTELLO ITALIA
Uffici/Sales OfficeVia L. Da Vinci, 40
I - 26011 • Casalbuttano (CR) • ItalyPh. +39 0374 3642
Fax +39 0374 360336
Castello Italia was established in Casalmorano (near Cremona, Italy) in 1965 and was among the first companies all around the world to specialize in the extrusion of polyamide and polyurethane to produce tubes. With more than 40 years of experience in the market of plastic material processing, Castello Italia has always been particularly active in aiming to quality, innovation and flexibility with reference to customers’ requests.Thanks to these key characteristics, Castello Italia has reached a successful positioning both in the market of pneumatic automation for distributing compressed air and fluids at low pressure, and in the branch of braking systems of vehicles.Concerning the latter sector, all our tubes are produced with raw materials complying with the international norms in force (DIN, SAE, NF, BS, ISO).Thanks to its own Research & Development department and to advanced machinery, Castello Italia can experiment and produce for its clients customized items constantly oriented to the most innovative and technological materials.
Castello Italia nasce a Casalmorano (Cremona, Italia) nel 1965 ed è stata tra le prime aziende al mondo a specializzarsi nell’estrusione delle poliammidi e poliuretani per la produzione di tubi.Con oltre 40 anni di esperienza nel mercato della lavorazione delle materie plastiche, la Castello Italia si è sempre distinta per la grande ricerca della qualità, dell’innovazione e della flessibilità nei confronti delle richieste dei propri clienti.Grazie a queste prerogative fondamentali Castello Italia si è posizionata con successo sia nel mercato dell’automazione pneumatica per il passaggio dell’aria compressa e dei fluidi a basse pressioni sia in quello dell’automotive nel settore dei sistemi frenanti.Per quanto riguarda quest’ultimo settore i nostri tubi sono tutti realizzati con materiali con-formi alle normative internazionali vigenti (DIN, SAE, NF, BS, ISO).Castello Italia grazie al proprio ufficio ricerca e sviluppo ed a un parco macchine all’avanguardia è in grado di sperimentare e creare per i propri clienti prodotti su misura e sempre proiettati alla ricerca dei materiali più innovativi e tecnologici.
Castello Italia stays at clients’ disposal for any special request about colour and size. Castello Italia products are not suitable for medical and food purposes. All Castello Italia tubes are ROHS-free.
La Castello Italia è a disposizione dei propri clienti per qualsiaisi richiesta particolare a livello di colori e dimensionale.I prodotti Castello Italia non sono utilizzabili in campo medicale e alimentare. Tutti i nostri tubi sono ROHS free.
CHI è CASTELLO ITALIAWHO CASTELLO ITALIA IS
3
Research, quality assurance, technical assistance to the customers, respect of the technical, environmental and safety regulations have been the key factors for Castello Italia’s success. Over the years the company has been able to gain a prominent position in branches where quality, reliability and timing are essential. In order to efficiently satisfy our customers’ requests and to be market competitive, the company daily follows and imple-ments the concepts expressed in the quality norm of reference UNI EN ISO 9001.Specific methods and procedures are constantly applied to guarantee the quality of the product and service offered to the customer. The monitoring of the product is carried out by competent, motivated and constantly updated personnel through highly technological tools supplied by the most important manufacturers (Mettler Toledo - Horiba - Perkin Elmer - Zumbach, …).The various quality checks made during the whole process, from the raw material up to the final product, guarantee the respect of the customers’ specifications, such as tight tolerance on the external diameter, reliable burst and working pressure, as well as customized printing, colours and packaging. As further confirmation of the fact that all the above mentioned procedures are not implemented simply to obtain the “certification”, our company operates trying to minimize the environmental impact. This aim, fixed according to the regulation 14001, is constantly kept under control thanks to parameters which show the performance over the time in terms of: Quality of the air released into the atmosphere, quantity of waste and level of noise.Least but not last, the company conveys an important message concerning the employment of “green products” such as the tube C.Bio, which can be easily recycled after their use, impacting this way as less as possible on the fragile balance human-environment. In order to comply with this goal, over the time Castello Italia has been supplying worldwide tubes which are ROHS free, as requested by the European Directive 2002/95 and 2002/96.
L’ECCELLENZA NEL SISTEMA QUALITÀTHE EXCELLENCE IN QUALITY SYSTEM
La ricerca, il controllo qualitativo , l’assistenza tecnica ai propri clienti , il rispetto delle normative tecniche, ambientali e di sicurezza del lavoro, sono la chiave del successo della Castello Italia. Negli anni la società ha saputo conquistare uno spazio di rilievo in settori dove la qualità, l’affidabilità e il tempismo sono richieste fondamentali. Per poter rispondere efficacemente ai requisiti richiesti dai propri clienti ed essere competitiva sul mercato, l’azienda applica ed implementa i concetti espressi nella normativa di riferimento UNI EN ISO 9001.La qualità del prodotto e del servizio fornito nel tempo ai nostri clienti è garantita dalla costante applicazione di metodi e procedure che strutturano l’organizzazione. Il controllo del prodotto erogato è affidato a personale competente motivato ed in continuo aggiornamento utilizzando strumenti di alto profilo tecnologico forniti dai maggiori produttori (Mettler Toledo - Horiba - Perkin Elmer - Zumbach).I controlli effettuati lungo la filiera produttiva a partire della materia prima sino ad arrivare al pezzo finale, garantiscono il rispetto dei requisiti definiti dai clienti che si traducono in tolleranze sul diametro del tubo molto ristrette, pressione di scoppio e d’utilizzo affida-bile, nella personalizzazione in termini di colore, marcatura, formato o packaging.A conferma che il sistema di gestione dell’organizzazione non è finalizzato al mero ottenimento del “certificato” , l’azienda opera cercando di minimizzare il proprio impatto ambientale. Tale obiettivo, fissato nel rispetto dei requisiti definiti nella 14001, è gestito utilizzando indicatori che nel tempo possono rendere evidente le performance in termini di:Qualità dell’aria immessa in atmosfera, Quantità di rifiuti prodotti, Qualità degli scarichi idrici e Livello del rumore prodotto.Non da ultima la nostra azienda veicola un importante messaggio relativamente all’utilizzo di prodotti “verdi” tipo il tubo C.Bio, che possano essere quindi facilmente recuperabili al termine del proprio ciclo vita impattando il meno possibile sul fragile equilibrio uomo-ambiente.In tale ottica da tempo i prodotti forniti dalla Castello Italia ed immessi sul mercato mondiale sono esenti da metalli pesanti come richiesto dalla Direttiva europea 2002/95 e 2002/96.
4
The sales team of Castello Italia leads an international network, created to offer top customer service. This sales network is organised as follows:
• Internal sales office• 9 agents on the Italian territory• 1 sales subsidiary in France - Castello France• 1 agent in Germany• 1 distributor in Poland dealing with all East European markets•1 distributor in Russia
Such an organization, very close to the market and its customers, allows Castello Italia to anticipate market needs and to propose innovative products.
With its sales office of 5 persons, Castello Italia is at your entire disposal for any kind of request about our products, their packaging and logistic matters. We speak perfectly Italian, French, English and German. So do not hesitate to contact us at: Phone: +39 0374 3642 I Fax: +39 0374 360336 I E-mail: [email protected]
Il team commerciale della Castello Italia gestisce la rete vendite italiana ed estera, creata al fine di elevare al massimo il servizio offerto ai propri clienti. Il network delle vendite è cosi composto:
• Ufficio Commerciale Interno• 9 agenzie nel mercato italiano• 1 filiale in Francia - Castello France• 1 agenzia nel mercato tedesco• 1 distributore in Polonia per i mercati dell’Est Europa• 1 distributore in Russia Attraverso tutto ciò Castello Italia è sempre più vicina alle esigenze del cliente ed è in grado di rispondere prontamente agli sviluppi di mercato e di proporre periodicamente novità.Il servizio commerciale interno, formato da 5 persone, è a vostra disposizione per qualsiasi informazione riguardante i prodotti, i confezionamenti e l’organizzazione delle spedizioni.
Lo staff Castello Italia dispone di persone che parlano fluentemente l’italiano, l’inglese, il francese e il tedesco ed è quindi in grado di fornirvi in tempo reale qualsiasi risposta nelle principali lingue europee.
Per contattare la divisione vendite Castello Italia: Telefono: +39 0374 3642 I Fax: +39 0374 360336 I E-mail: [email protected]
IL SERVIZIO COMMERCIALESALES ORGANIZATION
5
POLIAMMIDE 12 - PA12Questa molecola è sul mercato da oltre 30 anni e viene ricavata dalla policondensazione del laurillattame, monomero del petrolio. Il PA12 è un tecnopolimero usato in applicazioni ad alto valore aggiunto grazie alle seguenti caratteristiche:• Ottima stabilità dimensionale• Ottime prestazioni meccaniche, specialmente con le alte pressioni• Ottimo invecchiamento• Eccellenti resistenze all’abrasione• Buona resistenza agli agenti chimici• Ampia fascia di temperature d’utilizzo (da -60°C a +130°C)• Grande flessibilità• Eccellente resistenza all’idrolisiIl PA12 è largamente utilizzato negli impianti frenanti per camion e rimorchi, nelle linee di trasporto carburanti, nel trasporto di fluidi e gas, inclusa l’aria compressa, dove la resistenza chimica è un elemento discriminante.I tubi marchiati sono realizzati con questo materiale.
RILSAN® Poliammide 11 - PA11Questo polimero è ottenuto da una materia prima rinnovabile, l’olio di ricino. Il PA11 Rilsan® trova innumerevoli applicazioni grazie alle seguenti caratteristiche:• Eccellente resistenza chimica (in particolare idrocarburi e cloruro di zinco)• Larga fascia di temperature di utilizzo (da -60°C a +130°C)• Alta stabilità dimensionale• Buona resistenza all’impatto, specialmente a freddo• Ottimo invecchiamento anche negli ambienti umidi• Buona resistenza meccanica, in particolare alle alte pressioni• Grande flessibilità• Eccellente resistenza all’abrasione• Eccellente resistenza all’idrolisiQueste ottime proprietà sono state la principale motivazione che ha determinato l’utilizzo del PA11per la produ-zione di tubi gas ed off - shore, utilizzati nel settore estrattivo di petrolio ed affini. RILSAN® PA11 trova un impiego nel settore dell’articolo sportivo per la costruzione di scarponi e delle coperture degli sci dove la resistenza all’impatto e la leggerezza risultano elementi discriminanti.I tubi marchiati sono realizzati con questo materiale.
POLyAMIDE 12 - PA12Produced since more than 30 years from Oil source (Laurynlactam), PA12 is a techno-polymer used in high re-quirement applications because of its outstanding properties:• Very good dimensional stability• High mechanical properties, especially resistant to high pressure• Outstanding weathering resistance• Very good abrasion resistance• Excellent chemical resistance• Wide range of working temperature (from -60°C to +130°C)• High flexibility• Excellent hydrolysis resistancePA 12 is widely used in the air-braking systems for trucks and trailers, automotive fuel lines, fluid and gas (included compressed air) handlings where chemical resistance and strength are required. PA 12 is used in tubes.
RILSAN® POLyAMIDE 11 - PA11Produced from a renewable source (castor oil), Rilsan® PA11 is used in a large number of applications thanks to its outstanding properties:• Excellent resistance to chemicals in particular to hydrocarbons and zinc chloride• Wide range of working temperature (from -60°C to +130°C)• Excellent dimensional stability• Outstanding cold impact resistance• Excellent ageing resistance• Very good mechanical properties and especially at high pressure• High flexibility• Excellent abrasion resistance• Excellent hydrolysis resistanceThese properties of this unique material have been the reasons of its utilisation in harsh conditions such as in the Gas and Oil industry for offshore flow lines and gas pipes. Rilsan® PA11 is also used in top ski layer and ski boots applications where cold impact properties and light weight are required. Tubes made of Rilsan PA11 are printed .
MATERIE PRIMERAW MATERIALS
6
POLyuREthANE - PuThere are several types of thermoplastic Polyurethane (TPU) used for technical applications:• Polyester based TPU• Polyether based TPUProperties (mechanical and chemical) are quite different from each other.Polyether based TPU show better hydrolysis resistance than Polyester TPU which allows Polyether based TPU to be used when in contact with fluid (in particular with water) is needed. Polyether TPU is also less sensible to microbiological attack. Apart this major difference, both TPU families show similar properties such as:• Excellent abrasion resistance• Extreme flexibility (low E. modulus) even at low temperature (-40°C)• Good tear, cutting and perforation resistance• Fair mechanical properties • Excellent kinking behaviour leading to small bending radius.• Very good transparency• Resistant to oil and greaseTPU are used in a wide range of applications such as films, shoe soles, tubes…especially because of its abrasion resistance and extreme flexibility.Tube made in TPU are marked . The transparent tubes in TPU are marked .
POLIuREtANO - PuPer applicazioni tecniche ci sono due principali categorie di poliuretano:• TPU a base Poliestere• TPU a base PolietereLe proprietà (meccaniche e chimiche) dei due materiali sono diverse tra loro.Il Poliuretano a base polietere offre una maggiore resistenza all’idrolisi rispetto a quello a base poliestere ciò signifi-ca che per applicazioni a contatto con i fluidi (in particolare l’acqua) è consigliabile il poliuretano a base polietere.Il Poliuretano a base polietere risulta poi avere una maggiore resistenza agli attacchi microbiologici.A parte queste due principali differenze le due famiglie di poliuretano hanno caratteristiche similari come:• Eccellente resistenza all’abrasione• Eccezionale flessibilità (Modulo E molto basso) anche alle basse temperature (-40°C)• Ottima resistenza alla lacerazione, al taglio e alla perforazione• Discrete prestazioni meccaniche• Bassa possibilità di kinking grazie agli stetti raggi di curvatura ottenibili• Buona trasparenza• Resistente agli oli e ai grassiIl TPU è un materiale molto versatile e trova applicazione nei più svariati settori; produzione di film, suola delle calza-ture, attrezzature sportive, grazie alla estrema resistenza all’abrasione e flessibilità. I tubi marchiati sono realizzati con questi materiali cosi come i tubi per le colorazioni trasparenti.
7
POLIEtILENE - PEQuesto polimetro è costituito da monomeri di etilene, anch’esso di origine petrolifera. Il PE è utilizzato nelle ap-plicazioni sensibili al contenimento dei costi con un livello di prestazioni molto basso come i sacchetti di plastica per la spesa, tubi di scarico delle acque, film per packaging, tubi per basse pressioni (sotto i 5 bars). La famiglia del polietilene può essere divisa in due famiglie principali:• Polietilene ad alta densità (PEHD)• Polietilene a bassa densità (PELD)Il PEHD risulta avere proprietà meccaniche superiori al PELD a discapito della flessibilità. Entrambi i prodotti offrono un eccellente effetto barriera all’acqua quando però la temperatura non supera i +60°C.I tubi realizzati in PE sono marchiati .
POLIAMMIDE 6 - PA6Questa molecola prodotta da oltre 50 anni, deriva come il PA12, da una materia prima di origine petrolifera (ca-prolactame). Il PA6 è un polimero utilizzato in applicazioni in cui è particolarmente importante il rapporto prezzo/proprietà del prodotto. Le caratteristiche principali sono:• Buone proprietà meccaniche• Mediocre stabilità dimensionale (maggiormente igroscopico rispetto al PA12)• Buona resistenza alle alte pressioni• Buon invecchiamento• Buona resistenza chimicaA fronte delle sua proprietà il PA6 risulta consigliabile per la realizzazione i tubi e spirali per hobbistica, tubi cor-rugati e film per packaging in cui porta vantaggi economici rilevanti.I tubi marchiati sono realizzati con questo materiale.
COPOLyuREthANE – COPuNel 2010 la Castello Italia ha sviluppato e brevettato questo copolimero con lo scopo di migliorare la resistenza chimica e meccanica del poliuretano senza veder compromessi i vantaggi che gli hanno permesso di entrare con successo nel mercato della pneumatica industriale. Questo copolimero di Poliuretano (COPU) offre:• Eccellente resistenza alla pressione sottoforma di tubi• Eccellente flessibilità e resistenza alla piegatura• Eccellente resistenza all’abrasione• Eccellente resistenza alla lacerazione, al taglio e alla perforazione• Resistenza agli oli e al grassoCOPU può trovare svariati impieghi come nei tubi pneumatici in sostituzione del PA12 o del PU e nel mercato delle suole delle scarpe contro il PEBA grazie alla sue proprietà meccaniche e alla sua estrema flessibilità.I tubi realizzati in COPU sono marchiati con il nome
In 2010, Castello Italia, has developed a proprietary copolymer with the scope to improve the mechanical and che-mical properties of standard polyurethane without compromising the advantages which have made PU tubes very successful in the pneumatic industries. This copolymer of PU (COPU) offers:Excellent pression resistance for tubesExtreme flexibility and kinkig behaviourExcellent abrasion resistanceGood tear, cutting and perforationResistance to oil and greaseCOPU can be used in pneumatic tubes to replace PA12 or PU, shoe soles against PEBA because of its excellent mechanical properties combined with extreme flexibility.Tubes made of COPU are marked as
POLyAMIDE 6 – PA6Produced since more than 50 years from an oil source (Caprolactam), PA6 is a techno-polymer used for less strin-gent applications where a good compromise price / property is required. Main properties are:• Good mechanical properties• Mediocre dimensional stability (especially in humid environment compared to PA12)• High pressure resistance• Good ageing behaviour• Good chemical resistancePA 6 properties are suitable for hobby coils, packaging films, corrugated tubes with the best ratio performance/price. Tubes made in PA6 are marked .
8
POLItEtRAFLuORILEtILENE - PtFE (tEFLON®)Questa molecola è stata creata nel 1938 ed meglio conosciuto come TEFLON® marchio appartenente alla Dupont.L’acqua e le soluzioni liquide contenenti acqua, come molti cibi, non permeano il PTFE perché la sua superficie è total-mente inibitrice.Grazie a questa proprietà il PTFE è molto usato per il rivestimento di teglie e padelle anti-aderenti. è un materiale inerte e quindi è spesso usato in contenitori e tubi che contengono o trasportano agenti chimici rea-genti e corrosivi. Può essere anche usato come lubrificante, riducendo la frizione, l’usura e il consumo di energia dei macchinari.Le principali proprietà del PTFE sono:• Resistente alle alte temperature ( +250°C)• Basso coefficiente di frizione• Consigliabile per gli usi alimentari• Eccellente per le applicazioni chimiche e resistente all’idrolisiI tubi in PTFE sono chiamati .
POLItEtRAFLuORILEtILENE - PtFE (tEFLON®)Created in 1938, PTFE is well known under the name TEFLON® from Dupont. Because water and water-contai-ning substances like most foods do not wet PTFE, adhesion to PTFE surfaces is inhibited. Due to this property PTFE is used as a non-stick coating for pans and other cookware. It is very non-reactive, and so is often used in containers and tubes for reactive and corrosive chemicals. Where used as a lubricant, PTFE reduces friction, wear and energy consumption of machinery.Main properties of PTFE are:• High temperature resistance (+250°C)• Low friction coefficient• Suitable for food contact• Excellent chemical and hydrolysis resistanceTubes made of PTFE are called .
POLyvINyLIDENE FLuORIDE – PvDFPVDF is a special plastic material in the fluoropolymer family. It is used generally in applications requiring the highest purity, strength, and resistance to solvents, acids, bases and heat and low smoke generation during a fire event. It is commonly used in the chemical, semiconductor, medical and defense industries, as well as in lithium ion batteries.PVDF shows outstanding properties:• High purity• Excellent microbiological resistance• High flexibility and exceptional physical properties.• Suitable for food contactTubes made of PVDF are marked .
POLIFLuORuRO DI vINILIDENE - PvDFIl PVDF è un materiale plastico appartenente alla famiglia dei Fluoropolimeri. Viene usato generalmente nelle applicazioni che richiedono la più alta purezza, forza e resistenza ai solventi, agli acidi, alle basi e al calore grazie allo scarso rilascio di fumo in caso di incendio. Viene comunemente utilizzato nella chimica, nei semiconduttori, nelle applicazioni medicali e militari e pure nelle batterie agli ioni di litio.Le principali caratteristiche del PVDF sono:• Altissima purezza• Bassa possibilità di attacco microbiologico• Grande flessibilità e eccezionali proprietà meccaniche• Consigliabile per uso alimentareI tubi realizzati in PVDF sono marchiati .
POLyEthyLENE – PEProduced from an oil source (ethylene), PE is a commodity polymer used for cost sensitive application with low level of stress such as plastic waste bags, waste water tubes, packaging films, low pressure tubes (< 5bars). The Polyethylene family can be divided in 2 branches:• High density Polyethylene (HDPE)• Low density Polyethylene (LDPE)HDPE offers better mechanical properties than LDPE without renouncing to flexibility. Both products offer excel-lent water barrier properties when the temperature does not exceed +60 °C.Tubes made of PE are called .
9
APPLICAZIONIMAIN APPLICATIONS
Poliammide 12Polyamide 12
PTFe(TeFlon®, ...)
Poliammide 11Polyamide 11
Poliammide 6Polyamide 6
PoliureTanoPolyurethane
base
po
lieste
re
base
po
lieste
re
base
po
lieter
e
base
po
lieter
e
PolieTilenePolyethylene
SeTToreSeCtor
auTomoTiVe automotiVe
Termoformaturathermoforming
Trasporto BenzineFuel line
impianti frizioneCluch System
impianti freno rimorchi
Braking System for trailer
impianti freno camion
Braking System for truck
auTomazione induSTriale
induStrial automation
aria CompressaCompressed air
Trasporto FluidiFluid handling
alte Temperaturehigh temperatures
micropneumaticamicropneumatics
apparecchiature medicali
medical machineries
Trasporto Fluidi alimentari
Food & Fluid handling
Termoformatura (spirali)
thermoforming (coils)
agenti ChimiciChemical environments
* su specifica richiesta
* su specifica richiesta
* su specifica richiesta
* su specifica richiesta
PVdF(Kynar®, ...)
10
CoPu55 Shd
c.star
INDICEINDEX
Tubi/Tubes
Tubi Speciali/Special Tubes
Multitubi/Multitubes
Spirali/Coils
Automotive/Automotive
- Poliammide 12&PU / Polyamide 12&PU - Spirali multitubo / Multitube coils
- Poliammide 12 / Polyamide 12 - Poliammide 6 / Polyamide 6 - Poliuretano / Polyurethane
- Poliammide 12 / Polyamide 12 - Poliammide 11 / Polyamide 11
- Tubo Airbrake / Airbrake tube - Impianti frenanti / Airbraking systems - Super Pur
IND
EX
- Poliammide 12 atex / Polyamide 12 atex - Tubo in co - poliammide/Co - Polyamide tube
- Tubo anti scintilla/Anti spark tube - Teflon® ptfe
- Pvdf - PA12/PA11 self extinguishing
- Poliuretano retinato / Braided polyurethane - Pvc retinato / Braided pvc
- Pvc con spirale metallica / pvc with steel spiral - Tubo monostrato in pvc / Monolayer pvc tube
- Tubi grandi diametri / Large diameter tubes
- Poliammide 12 / Polyamide 12 - Poliammide 12 / Polyamide 12
- Poliammide 11 / Polyamide 11soft - Poliammide 12 Ultraflessibile /Ultraflexible PA12
- Co-Poliuretano 55 Sh D /Co-Polyurethane Tubes 55 Sh D
- Poliammide 6 / Polyamide 6 - Poliuretano / Polyurethane
- Poliuretano / Polyurethane - Polietilene / Polyethylene
Packaging/Packaging
Codici/How to order
Resistenze chimichePressione di scoppio/
Chemical resistance and burst pressure
& Packaging
Codifica Tubi e Spirali / Tubes and coils codes
Resistenze chimiche / Chemical resistancePressione scoppio istantaneo / Bursting pressure Note / Notes
11
- POLIAMMIDE 12 POLYAMIDE12
ItubiC.Best inPoliammide12per leapplicazionidellapneu-maticaindustrialevengonoestrusiconduegradidiflessibilità:1. FLEssIbILE:PA12PHL2. RIgIDO:PA12HL
C.Best tubesmadeofPolyamide12forpneumaticapplica-tionsareproposedwithtwolevelofflexibility:1. FLExIbLE:PA12PHL2. RIgID:PA12HL
1. PA 12 PHL
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
DIN 74324 solo neroonly black
DIN 73378 tutti i colori
all colours
3 mm
4 mm
4 mm
4 mm
5 mm
6 mm
8 mm
10 mm
10 mm
10 mm
12 mm
12 mm
12 mm
14 mm
14 mm
15 mm
15 mm
16 mm
18 mm
20 mm
22 mm
1,5 mm
2,5 mm
2,7 mm
2 mm
3 mm
4 mm
6 mm
8 mm
7 mm
7,5 mm
10 mm
9 mm
8 mm
12 mm
10 mm
12,5 mm
12 mm
12 mm
14 mm
16 mm
18 mm
0,75 mm
0,75 mm
0,65 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
1,25 mm
1 mm
1,5 mm
2 mm
1 mm
2 mm
1,25 mm
1,5 mm
2 mm
2 mm
2 mm
2 mm
15 mm
20 mm
25 mm
15 mm
30 mm
35 mm
40 mm
60 mm
45 mm
50 mm
85 mm
70 mm
80 mm
85 mm
90 mm
100 mm
100 mm
150 mm
190 mm
180 mm
200 mm
Pressione esercizio (a 23°C)Working pressure (at 23°C)
44 bar
31 bar
26 bar
44 bar
33 bar
27 bar
19 bar
15 bar
24 bar
19 bar
12 bar
19 bar
27 bar
10 bar
22 bar
12 bar
15 bar
19 bar
17 bar
15 bar
13 bar
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
133 bar
92 bar
78 bar
133 bar
100 bar
80 bar
57 bar
44 bar
71 bar
57 bar
36 bar
57 bar
80 bar
31 bar
67 bar
36 bar
44 bar
57 bar
50 bar
44 bar
40 bar
PA12
12
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesterno,secondoDIN73378,sono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal3mmal10mm:+/-0,03mmDal11mmal22mm:+/-0,05mm
ToleranceonexternaldiameterasperDIN73378Norm:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From3mmto10mm:+/-0,03mmFrom11mmto22mm:+/-0,05mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-60°Ca+130°C
From-60°Cto+130°C
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableonpage65.
GAMMA COLORICOLOUR RANGE
PerilPA12PHL:ForPA12PHL: Naturale
NaturalNeroblack
Azzurrobluesky
bluDarkblue
RossoRed
gialloYellow
Verdegreen
ArancioOrange
NT NR AZ bL RO gI VE AR
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- DIN 73378 10 X 1 mm - PA 12 PHL - C.BEST - 3035 - 11 - 134 - 20:45NormativaNormative
MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
% delle press.
Temp.
100% 87%74% 64% 57%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
13
PA12
TubiTubes
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
2. PA 12 HL
4 mm
4 mm
5 mm
6 mm
6 mm
8 mm
8 mm
10 mm
12 mm
12 mm
12 mm
2,5 mm
2 mm
3 mm
3 mm
4 mm
5 mm
6 mm
8 mm
10 mm
9 mm
8 mm
0,75 mm
1 mm
1 mm
1,5 mm
1 mm
1,5 mm
1 mm
1 mm
1 mm
1,5 mm
2 mm
30 mm
25 mm
40 mm
50 mm
45 mm
30 mm
50 mm
70 mm
95 mm
80 mm
90 mm
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
185 bar
267 bar
200 bar
267 bar
160 bar
185 bar
114 bar
89 bar
73 bar
114 bar
60 bar
Pressione esercizio (a 23°C)Working pressure (at 23°C)
62 bar
89 bar
67 bar
89 bar
53 bar
61 bar
38 bar
30 bar
24 bar
38 bar
20 bar
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
DIN 74324 solo neroonly black
DIN 73378 tutti i colori
all colours
•
•
•
•
•
•
•
•
•
•
•
•
•
•
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesterno,secondoDIN73378,sono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal3mmal10mm:+/-0,03mmDal11mmal22mm:+/-0,05mm
ToleranceonexternaldiameterasperDIN73378Norm:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From3mmto10mm:+/-0,03mmFrom11mmto22mm:+/-0,05mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-60°Ca+130°C
From-60°Cto+130°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Our standard is with polyethyle-nefilmaround.Forotherkindofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- DIN 73378 - 6 X 1,5 mm - PA 12 HL - C.BEST - 2456 - 10 - 342 - 21:47NormativaNormative
MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
GAMMA COLORICOLOUR RANGE
PerilPA12HL:ForPA12HL: Naturale
NaturalNeroblack
NT NR
LaCastello Italiaconunminimod’ordinedi3.000mè ingra-do di offrirvi tubi di colori personalizzati secondo tabella RAL.
Castello Italiaupon requestcanoffercustomcolours followingRALspecificationforaminimumdeliveryof3.000m.
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
100%81%
61% 50% 44% 39% 34%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C 70°C 80°C
% delle press.
Temp.
PA12
14
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
I tubi C.Light in Poliammide 12 per le applicazioni dellapneumaticaindustrialevengonoestrusiconilgradodifles-sibilitàPHLincolorazionitrasparentialfinedipotervederecon chiarezza all’interno del tubo l’eventuale presenza diimpurità.
C.Light tubesmade of Polyamide12 for pneumatic applica-tionsareproposedwith levelof flexibilityPHL insee-throughcoloration.Thistransparencyallowstocheckforimpuritiesinthesystem.
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesterno,secondoDIN73378,sono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal3mmal10mm:+/-0,03mmDal11mmal22mm:+/-0,05mm
ToleranceonexternaldiameterasperDIN73378Norm:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From3mmto10mm:+/-0,03mmFrom11mmto22mm:+/-0,05mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-60°Ca+130°C
From-60°Cto+130°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
- POLIAMMIDE 12 POLYAMIDE12
4 mm
4 mm
4 mm
6 mm
8 mm
10 mm
12 mm
14 mm
2,5 mm
2,7 mm
2 mm
4 mm
6 mm
8 mm
10 mm
12 mm
0,75 mm
0,65 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1 mm
20 mm
25 mm
15 mm
35 mm
40 mm
60 mm
85 mm
85 mm
31 bar
26 bar
44 bar
27 bar
19 bar
15 bar
12 bar
10 bar
92 bar
78 bar
133 bar
80 bar
57 bar
44 bar
36 bar
31 bar
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
DIN 74324 solo neroonly black
DIN 73378 tutti i colori
all colours
•
•
•
•
•
PA12
15
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- DIN 73378 - 8 X 1 mm - PA 12 PHL - C.LIGHT - 1109 - 08 - 164 - 15:33NormativaNormative
MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
GAMMA COLORICOLOUR RANGE
PerilPA12:ForPA12:
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
CristalloCrystal
Azzurrobluesky
RossoRed
gialloYellow
Verdegreen
CR AT RT gT VT
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
% delle press.
Temp.
100% 87%74% 64%
57%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
PA12
16
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
- POLIAMMIDE 11 POLYAMIDE11
ItubiC.BioinPoliammide11perleapplicazionidellapneuma-ticaindustrialevengonoestrusicontregradidiflessibilità:1. Flessibile:PA11PHL2.Rigido:PA11HL3. Ultra-Flessibile:PA11HIPHL
C.BiotubesmadeofPolyamide11forpneumaticapplicationsareproposedwiththreelevelsofflexibility:1. Flexible:PA11PHL2. Rigid:PA11HL3. Utra-Flexible:PA11HIPHL
1. PA 11 PHL
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
DIN 74324 solo neroonly black
DIN 73378 tutti i colori
all colours
3 mm
4 mm
4 mm
4 mm
5 mm
6 mm
8 mm
10 mm
10 mm
12 mm
12 mm
12 mm
14 mm
14 mm
15 mm
15 mm
16 mm
20 mm
22 mm
1,5 mm
2,5 mm
2,7 mm
2 mm
3 mm
4 mm
6 mm
8 mm
7 mm
10 mm
9 mm
8 mm
12 mm
10 mm
12,5 mm
12 mm
12 mm
16 mm
18 mm
0,75 mm
0,75 mm
0,65 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
1 mm
1,5 mm
2 mm
1 mm
2 mm
1,25 mm
1,5 mm
2 mm
2 mm
2 mm
15 mm
20 mm
25 mm
15 mm
30 mm
35 mm
40 mm
60 mm
45 mm
85 mm
70 mm
80 mm
85 mm
90 mm
100 mm
100 mm
150 mm
180 mm
200 mm
44 bar
31 bar
23 bar
44 bar
33 bar
27 bar
19 bar
15 bar
24 bar
12 bar
19 bar
27 bar
10 bar
22 bar
12 bar
15 bar
19 bar
15 bar
13 bar
133 bar
92 bar
68 bar
133 bar
100 bar
80 bar
57 bar
44 bar
71 bar
36 bar
57 bar
80 bar
31 bar
67 bar
36 bar
44 bar
57 bar
44 bar
40 bar
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PA11
17
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesterno,secondoDIN73378,sono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal3mmal10mm:+/-0,03mmDal11mmal22mm:+/-0,05mm
ToleranceonexternaldiameterasperDIN73378Norm:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From3mmto10mm:+/-0,03mmFrom11mmto22mm:+/-0,05mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-60°Ca+130°C
From-60°Cto+130°C
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
GAMMA COLORICOLOUR RANGE
PerilPA11PHL:ForPA11PHL:
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
NaturaleNatural
Neroblack
Azzurrobluesky
bluDarkblue
RossoRed
gialloYellow
Verdegreen
ArancioOrange
NT NR AZ bL RO gI VE AR
% delle press.
Temp.
100%87%
74% 64% 57% 52% 47%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C 70°C 80°C
PA11
18
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- DIN 73378 - 10 X 1 mm - PA 11 PHL - C.bio - 4385 - 11 - 235 - 19:35NormativaNormative
MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
2. PA 11 HL
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesterno,secondoDIN73378,sono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal3mmal10mm:+/-0,03mmDal11mmal22mm:+/-0,05mm
ToleranceonexternaldiameterasperDIN73378Norm:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From3mmto10mm:+/-0,03mmFrom11mmto22mm:+/-0,05mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-60°Ca+130°C
From-60°Cto+130°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
DIN 74324 solo neroonly black
DIN 73378 tutti i colori
all colours
4 mm
4 mm
5 mm
6 mm
6 mm
8 mm
8 mm
10 mm
12 mm
12 mm
12 mm
2,5 mm
2 mm
3 mm
3 mm
4 mm
5 mm
6 mm
8 mm
10 mm
9 mm
8 mm
0,75 mm
1 mm
1 mm
1,5 mm
1 mm
1,5 mm
1 mm
1 mm
1 mm
1,5 mm
2 mm
30 mm
25 mm
40 mm
50 mm
45 mm
30 mm
50 mm
70 mm
95 mm
80 mm
90 mm
62 bar
89 bar
67 bar
89 bar
53 bar
61 bar
38 bar
30 bar
24 bar
38 bar
53 bar
185 bar
267 bar
200 bar
267 bar
160 bar
185 bar
114 bar
89 bar
73 bar
114 bar
160 bar
•
•
•
•
•
•
•
•
•
•
•
•
•
•
GAMMA COLORICOLOUR RANGE
PerilPA11HL:ForPA11HL: Naturale
NaturalNeroblack
NT NR
LaCastello Italiaconunminimod’ordinedi3.000mè ingra-do di offrirvi tubi di colori personalizzati secondo tabella RAL.
Castello Italiaupon requestcanoffercustomcolours followingRALspecificationforaminimumdeliveryof3.000m.
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
% delle press.
Temp.
100%87%
74% 64% 57% 52% 47%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C 70°C 80°C
PA11
19
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- DIN 73378 - 6 X 1,5 mm - PA 11 HL - C.bio - 2275 - 10 - 134 - 14:30NormativaNormative
MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
3. PA11 HIPHL
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesternosono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal3mmal10mm:+/-0,03mmDal11mmal22mm:+/-0,05mm
Toleranceonexternaldiameter:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From3mmto10mm:+/-0,03mmFrom11mmto22mm:+/-0,05mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-60°Ca+130°C
From-60°Cto+130°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- DIN 73378 - 10 X 1 mm - RILSAN PA 11 HIPHL - C.BIO - 1109 - 08 - 164 - 15:33NormativaNormative
MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
GAMMA COLORICOLOUR RANGE
PerilPA11Mb3610:ForPA11Mb3610:
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
NaturaleNatural
Neroblack
NT NRbluDarkblue
RossoRed
gialloYellow
bL RO gI
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
% delle press.
Temp.
100%80%
62% 55% 49% 46% 43%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C 70°C 80°C
PA11
20
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
4 mm
6 mm
8 mm
10 mm
12 mm
12 mm
12 mm
14 mm
2 mm
4 mm
6 mm
8 mm
10 mm
9 mm
8 mm
10 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
2 mm
2 mm
25 mm
30 mm
35 mm
55 mm
80 mm
70 mm
80 mm
80 mm
33 bar
20 bar
14 bar
11 bar
9 bar
14 bar
20 bar
17 bar
100 bar
60 bar
43 bar
33 bar
27 bar
43 bar
60 bar
50 bar
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
ItubiC.SoftsonorealizzaticonunpolimeroabasePA12,as-solutamenterivoluzionario,edoffronoall’utilizzatorefinalelemiglioricaratteristichedelPoliammide12,resistenzachimi-caemeccanica,edelPoliuretanoshA98,grandeflessibilitàemorbidezza. Nelle principali applicazioni della pneumaticaindustrialeilC.Softdàlapossibilitàdiutilizzareun’unicatipo-logiadi tubirisolvendonellostessotempo leproblematichelegateall’idrolisi,ai raggidicurvatura,semprepiùstretti,ealletolleranzeconiraccordiautomatici.
C. Soft tubesaremadeofarevolutionaryPA12combiningthebestpropertiesofPolyamide12intermsofchemicalandmechanicalresistancewiththeflexibilityandsoftnessofthePolyurethane sh98A.C. Soft tubes are recommended formostofthepneumaticapplicationssinceC. Softtubessolveallproblemsrelatedtohydrolysis,narrowbendingradiusandtighttoleranceforquickfittings.
- POLIAMMIDE 12 ULTRAFLESSIBILE ULTRAFLExIbLEPOLYAMIDE12
PA12
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
4 mm
6 mm
8 mm
10 mm
12 mm
2,5 mm
2 mm
4 mm
6 mm
8 mm
10 mm
0,75 mm
1 mm
1 mm
1 mm
1 mm
1 mm
20 mm
15 mm
25 mm
40 mm
55 mm
90 mm
20 bar
28 bar
17 bar
12 bar
10 bar
8 bar
60 bar
86 bar
52 bar
37 bar
29 bar
24 bar
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesterno,secondoDIN73378,sono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal3mmal10mm:+/-0,03mmDal11mmal22mm:+/-0,05mm
ToleranceonexternaldiameterasperDIN73378Norm:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From3mmto10mm:+/-0,03mmFrom11mmto22mm:+/-0,05mm
TEMPERATURA D’USOTEMPERATURE RANGE Da-60°Ca+100°C
From-60°Cto+100°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
21
PA12
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
GAMMA COLORICOLOUR RANGE
PerilPA12Ultraflessibile:ForPA12Ultraflexible Naturale
NaturalNeroblack
Azzurrobluesky
NT NR AZRossoRed
RO
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- 8 X 1 mm - PA 12 - C.SOFT - 12 bar - 1109 - 08 - 164 - 15:33MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Pressioned’esercizioWorkingpressure
Numerodilottobatchnumber
% delle press.
Temp.
100%83% 71% 62% 55%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
22
- CO-POLIURETANO 55 Sh D CO-POLYURETHANE55shDTUbEs
Questoinnovativotuboconsentediaverelemiglioricaratteristichedelpoliuretanoedelpoliammideinununicoprodotto.ItubiC.Star,realizzaticonun’esclusivamescoladico-poliuretanooffrono:•Elevataflessibilità•Ottimiraggidicurvatura(ugualeaunPUsh98A)•buonetolleranze(simileaunPA12PHL)•Resistenzaall’acqua(ugualeaunPA12PHL)•Discretaresistenzaagliagentichimici(superioreaunPUsh98A)•Discretaresistenzaallatemperatura(superioreaunPUsh98A).Questitubirisultanoidealiperilmercatodellapneumaticaindustrialeincuisononecessariraggidicurvaturamoltoristretti,pressionifinoa12bar(rispettoa8bardelpoliuretano)emaneggevolezzaneimon-taggigraziealperfettoinserimentoneiraccordiadinnestorapido.
ThisveryinnovativetubecombinesinoneproductthebestpropertiesofpolyurethaneandtheonesofthePolyamide.C.Startubesaremadeofanexclusiverecipeofco-polyurethaneandoffers:•Highflexibility•Excellentbendingradius•TightertolerancesthanPU•goodhydrolysisresistance•goodchemicalresistance•Excellenttempera-tureresistance.Thesetubesareparticularlyindicatedforthepneumaticmar-ketwheretightbendingradiusformountinginnarrowcabinsarerequestedtogetherwithpressure>12barsandpush-infittings.
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
TEMPERATURA D’USOTEMPERATURE RANGE
Da-40°Ca+100°C
From-40°Cto+100°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Disponibilisurichiesta
Availableonrequest
23
CO55shD
TOLLERANZA / TOLERANCELenostretolleranzesuldiametroesternosono:Dal4mmal12mm:+/-0,10mmDal12mmal15mm:+/-0,15mm
Toleranceonexternaldiameter:From4mmto12mm:+/-0,10mmFrom12mmto15mm:+/-0,15mm
CONFEZIONAMENTO PACkAGINGIl nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
4 mm
6 mm
8 mm
10 mm
12 mm
12 mm
14 mm
14 mm
15 mm
15 mm
2,5 mm
4 mm
6 mm
8 mm
10 mm
9 mm
12 mm
10 mm
12 mm
12,5 mm
0,75 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
1 mm
2 mm
1,5 mm
1,25 mm
10 mm
15 mm
25 mm
35 mm
60 mm
45 mm
60 mm
50 mm
60 mm
55 mm
22 bar
19 bar
16 bar
12 bar
8 bar
13 bar
7 bar
16 bar
10 bar
8 bar
65 bar
57 bar
47 bar
36 bar
25 bar
40 bar
22 bar
47 bar
31 bar
25 bar
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
GAMMA COLORICOLOUR RANGE
PerilC.star:ForC.star: Naturale
Natural
NTNeroblack
NRAzzurrobluesky
AZ
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
8 X 1 mm - Copu55shd- C.Star - 8093 - 11 - 155 - 20:45MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
% delle press.
Temp.
100%83% 71% 62% 55%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
24
CO55shD
grigiometalloMetalgrey
gRRossoRed
ROgialloYellow
gIVerdegreen
VE
- POLIAMMIDE 6POLYAMIDE6
1. PA 6 HIHL
I tubiC.Six in Poliammide 6 per le applicazioni della pneumaticaindustrialevengonoestrusiconduegradidiflessibilità:1. Flessibile:PA6HIHL 2. Rigido:PA6HL
C.Six tubesmadeofPolyamide6 for pneumatic applications areproposedwithtwolevelsofflexibility:1. Flexible:PA6HIHL 2. Rigid:PA6HL
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
6 mm
6 mm
8 mm
10 mm
12 mm
12 mm
12 mm
14 mm
2 mm
4 mm
3,5 mm
3 mm
6 mm
8 mm
10 mm
9 mm
8 mm
10 mm
1 mm
1 mm
1,25 mm
1,5 mm
1 mm
1 mm
1 mm
1,5 mm
2 mm
2 mm
30 mm
45 mm
40 mm
40 mm
60 mm
70 mm
90 mm
90 mm
80 mm
85 mm
41 bar
25 bar
33 bar
41 bar
18 bar
14 bar
11 bar
18 bar
25 bar
21 bar
124 bar
74 bar
98 bar
124 bar
53 bar
41 bar
34 bar
53 bar
74 bar
62 bar
TEMPERATURA D’USOTEMPERATURE RANGE Da-60°Ca+130°CFrom-60°Cto+130°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.Checkthetableatpage65.
CONFEZIONAMENTO / PACkAGING
Ilnostrostandardèconfilmdipolie-tilene.Perlealtretipologiedipacka-gingconsultarelapagina61.
Our standard iswith polyethylene filmaround. For other kinds of packagingcheckpage61.
TOLLERANZA / TOLERANCE
Lenostretolleranzesuldiametroesternosono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
Toleranceonexternaldiameter:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
MARCATURA / MARkINGLanostramarcaturastandardè:Ourstandardmarkingis:
- 8 x 1 mm - PA 6 HIHL - C.SIX - 2214 - 09 - 057 - 16:33MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
% delle press.
Temp.
100%83% 71% 58% 54% 51% 48%
0%20%40%60%80%
100%120%
20°C 30°C 40°C 50°C 60°C 70°C 80°C
GAMMA COLORICOLOUR RANGE
PerilPA6HIHL:ForPA6HIHL:
LaCastello Italiaconunminimod’ordinedi3.000mè ingra-do di offrirvi tubi di colori personalizzati secondo tabella RAL.
Castello Italiaupon requestcanoffercustomcolours followingRALspecificationforaminimumdeliveryof3.000m.
NaturaleNatural
Neroblack
NT NRArancioOrange
AR
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.standard100mt.Otherlenghtsuponrequest.
PA6
25
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
2. PA 6 HL
GAMMA COLORICOLOUR RANGE
PerilPA6HL:ForPA6HL: Naturale
NaturalNeroblack
NT NR
LaCastello Italiaconunminimod’ordinedi3.000mè ingra-do di offrirvi tubi di colori personalizzati secondo tabella RAL.
Castello Italiaupon requestcanoffercustomcolours followingRALspecificationforaminimumdeliveryof3.000m.
TEMPERATURA D’USOTEMPERATURE RANGE
Da-60°Ca+130°C
From-60°Cto+130°C
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesternosono:Dal3mmal10mm:+/-0,10mmDal11mmal22mm:+/-0,15mm
Toleranceonexternaldiameter:From3mmto10mm:+/-0,10mmFrom11mmto22mm:+/-0,15mm
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- 8 x 1 mm - PA 6 HL - C.SIX - 2214 - 09 - 057 - 16:33MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
6 mm
6 mm
8 mm
10 mm
12 mm
12 mm
12 mm
14 mm
2 mm
4 mm
3,5 mm
3 mm
6 mm
8 mm
10 mm
9 mm
8 mm
10 mm
1 mm
1 mm
1,25 mm
1,5 mm
1 mm
1 mm
1 mm
1,5 mm
2 mm
2 mm
35 mm
50 mm
45 mm
45 mm
65 mm
75 mm
95 mm
95 mm
85 mm
90 mm
267 bar
160 bar
211 bar
267 bar
114 bar
89 bar
73 bar
114 bar
160 bar
133 bar
89 bar
53 bar
70 bar
89 bar
38 bar
30 bar
24 bar
38 bar
53 bar
44 bar
% delle press.
Temp.
100%83% 71%
58% 54% 51% 48%
0%20%40%60%80%
100%120%
20°C 30°C 40°C 50°C 60°C 70°C 80°C
PA6
26
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
- POLIURETANO POLYURETHANE
ItubiC.Flex inpoliuretanoper leapplicazionidellapneumaticaindustrialevengonoestrusiconduebasidifferentietrelivellidiflessibilità:1. basePoliestere:shoreA982. basePolietere:shoreA953. basePolietere:shoreA90C.Flextubesmadeofpolyurethaneforpneumaticapplicationsarepro-posedwithtwodifferentrawmaterialandthreelevelflexibility:1. Polyesterbased:shoreA982. Polyetherbased:shoreA953. Polyetherbased:shoreA90
1. PU Sh. A98
TOLLERANZA / TOLERANCELenostretolleranzesuldiametroesternosono:Dal4mmal8mm:+/-0,10mmDal10mmal12mm:+/-0,15mmsurichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal4mmal8mm:+/-0,07mmDal10mmal12mm:+/-0,10mm
Toleranceonexternaldiameter:From4mmto8mm:+/-0,10mmFrom10mmto15mm:+/-0,15mmUponrequestwecoulddeliverhighprecisiontubesatthistolerance:From4mmto8mm:+/-0,07mmFrom10mmto12mm:+/-0,10mm
RESISTENZE CHIMICHECHEMICAL RESISTANCEControllarelatabellaapagina65.Checkthetableatpage65.
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
3 mm
4 mm
4 mm
5 mm
6 mm
8 mm
8 mm
8 mm
10 mm
10 mm
10 mm
12 mm
12 mm
14 mm
16 mm
1,5 mm
2,5 mm
2 mm
3 mm
4 mm
6 mm
5,5 mm
5 mm
8 mm
7,5 mm
7 mm
9 mm
8 mm
10 mm
12 mm
0,75 mm
0,75 mm
1 mm
1 mm
1 mm
1 mm
1,25 mm
1,5 mm
1 mm
1,25 mm
1,5 mm
1,5 mm
2 mm
2 mm
2 mm
10 mm
10 mm
15 mm
10 mm
20 mm
25 mm
35 mm
25 mm
35 mm
30 mm
25 mm
45 mm
35 mm
50 mm
55 mm
22 bar
15 bar
22 bar
17 bar
13 bar
10 bar
14 bar
17 bar
7 bar
10 bar
12 bar
10 bar
13 bar
11 bar
10 bar
67 bar
46 bar
67 bar
50 bar
40 bar
29 bar
41 bar
51 bar
22 bar
29 bar
35 bar
29 bar
40 bar
33 bar
29 bar
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.
100%83% 72% 64%
47%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C CONFEZIONAMENTO PACkAGINGIl nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA / MARkINGLanostramarcaturastandardè:Ourstandardmarkingis:
- 8 x 1 mm - PU SH A 98 - C.FLEX - 8115 - 09 - 113 - 20:50MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
TEMPERATURA D’USOTEMPERATURE RANGEDa-40°Ca+60°CFrom-40°Cto+60°C
LUNGHEZZA MATASSAROLL SIZEstandard100mt.Altriavvolgimentisurichiesta.standard100mt.Otherlenghtsuponrequest.
PU
27
2. PU Sh. A950 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
4 mm
6 mm
8 mm
10 mm
10 mm
12 mm
12 mm
16 mm
2,5 mm
2 mm
4 mm
6 mm
7 mm
8 mm
8 mm
9 mm
10 mm
0,75 mm
1 mm
1 mm
1 mm
1,5 mm
1 mm
2 mm
1,5 mm
3 mm
19 mm
10 mm
15 mm
25 mm
30 mm
40 mm
50 mm
50 mm
60 mm
9 bar
12 bar
9 bar
8 bar
6 bar
5 bar
6 bar
5 bar
5 bar
36 bar
48 bar
39 bar
32 bar
24 bar
20 bar
24 bar
20 bar
20 bar
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
TOLLERANZATOLERANCELenostretolleranzesuldiametroesternosono:Dal4mmal6mm:+/-0,10mmDal8mmal12mm:+/-0,15mmsurichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal4mmal6mm:+/-0,07mmDal8mmal12mm:+/-0,10mmToleranceonexternaldiameter:From4mmto6mm:+/-0,10mmFrom8mmto12mm:+/-0,15mmUponrequestwecoulddeliverhighprecisiontubesatthistolerance:From4mmto6mm:+/-0,07mmFrom8mmto12mm:+/-0,10mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-40°Ca+60°C
From-40°Cto+60°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
GAMMA COLORICOLOUR RANGE
PerilPUsh.A95:ForPUsh.A95: Naturale
NaturalNeroblack
NT NRAzzurrobluesky
AZ
LaCastello Italiaconunminimod’ordinedi3.000mè ingra-do di offrirvi tubi di colori personalizzati secondo tabella RAL.
Castello Italiauponrequestcanoffercustomcolours followingRALspecificationforaminimumdeliveryof3.000m.
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.
100%83% 72% 64%
47%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- 8 x 1 mm - PU SH A 95 - C.FLEX - 8115 - 09 - 113 - 20:50MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
PU
28
GAMMA COLORICOLOUR RANGE
PerilPUsh.A98:ForPUsh.A98:
La Castello Italia con unminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.Castello Italia upon request can offercustomcoloursfollowingRALspecifica-tionforaminimumdeliveryof3.000m.
NaturaleNatural
Neroblack
Azzurrobluesky
RossoRed
gialloYellow
Verdegreen
grigiometalloMetalgrey
NT NR AZ RO gI VEgR
*Nondisponibileamagazzino *Notavailableonstock
*
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
3. PU Sh. A90
Questatipologiaditubioffreun’elevataflessibilitàmabassaresistenzaallepressioni.Thistubescouldofferanelevatedflexibilitybutnotinhighpressureapplications.
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesternosono:Dal4mmal8mm:+/-0,10mmDal10mmal12mm:+/-0,15mmsurichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal4mmal8mm:+/-0,07mmDal10mmal12mm:+/-0,10mm
Toleranceonexternaldiameter:From4mmto8mm:+/-0,10mmFrom10mmto12mm:+/-0,15mmUponrequestwecoulddeliverhighprecisiontubesatthistolerance:From4mmto8mm:+/-0,07mmFrom10mmto12mm:+/-0,10mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-40°Ca+60°C
From-40°Cto+60°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
GAMMA COLORICOLOUR RANGE
PerilPUsh.A90:ForPUsh.A90:
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
Azzurrobluesky
AZ
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.0%20%40%60%80%
100%120%
20°C
100 %
60 %40 %
30°C 40°C
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
4 mm
5 mm
6 mm
8 mm
10 mm
10 mm
12 mm
12 mm
14 mm
2,5 mm
2 mm
3 mm
4 mm
6 mm
7 mm
8 mm
8 mm
9 mm
10 mm
0,75 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
1 mm
2 mm
1,5 mm
2 mm
20 mm
20 mm
25 mm
30 mm
40 mm
35 mm
30 mm
30 mm
50 mm
120 mm
12 bar
18 bar
13 bar
18 bar
8 bar
9 bar
11 bar
11 bar
8 bar
9 bar
37 bar
53 bar
40 bar
53 bar
23 bar
28 bar
32 bar
32 bar
23 bar
27 bar
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- 8 x 1 mm - PU SH A 90 - C.FLEX - 8115 - 09 - 113 - 20:50MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
PU
29
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
- POLIURETANOPOLYURETHANE
ItubiC.kolorinpoliuretanoperleapplicazionidellapneumati-caindustrialevengonoestrusisoloinbasepoliestere(shoreA98).
C.kolor tubes made of polyurethane for pneumatic applica-tionsareonlyproposedwithPolyesterbased(shoreA98).
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesternosono:Dal4mmal8mm:+/-0,10mmDal10mmal12mm:+/-0,15mm
surichiestapossiamooffrirvitubiadaltaprecisioneconleseguentitolleranze:Dal4mmal8mm:+/-0,07mmDal10mmal12mm:+/-0,10mm
Toleranceonexternaldiameter:From4mmto8mm:+/-0,10mmFrom10mmto15mm:+/-0,15mm
Uponrequestwecoulddeliverhighprecisiontubesatthistolerance:From4mmto8mm:+/-0,07mmFrom10mmto12mm:+/-0,10mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da-40°Ca+60°C
From-40°Cto+60°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
4 mm
5 mm
6 mm
8 mm
8 mm
8 mm
10 mm
10 mm
10 mm
12 mm
12 mm
2,5 mm
2 mm
3 mm
4 mm
6 mm
5,5 mm
5 mm
8 mm
7,5 mm
7 mm
9 mm
8 mm
0,75 mm
1 mm
1 mm
1 mm
1 mm
1,25 mm
1,5 mm
1 mm
1,25 mm
1,5 mm
1,5 mm
2 mm
10 mm
15 mm
10 mm
20 mm
25 mm
35 mm
25 mm
35 mm
30 mm
25 mm
45 mm
35 mm
46 bar
67 bar
50 bar
40 bar
29 bar
41 bar
51 bar
22 bar
29 bar
35 bar
29 bar
40 bar
15 bar
22 bar
17 bar
13 bar
10 bar
14 bar
17 bar
7 bar
10 bar
12 bar
10 bar
13 bar
30
PU
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
GAMMA COLORICOLOUR RANGE
PerilPUsh.A98C.Kolor:ForPUshA98C.Kolor
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
CristalloCrystal
Azzurrobluesky
RossoRed
gialloYellow
Verdegreen
CR AT RT gT VT
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
- 8 x 1 mm - PU SH A 98 - C.KOLOR - 1109 - 08 - 164 - 15:33MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
% delle press.
Temp.
100%83°% 72% 64%
47%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
31
PU
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
- POLIETILENEPOLYETHYLENE
IlPolietileneabassadensitàpuòessereutilizzatoinunagammaristrettaditemperaturecompresetrai-10°Ce+60°C.ItubiC.EcoinPolietileneperleapplicazionidellapneumaticaindustrialevengonoestrusiconduegradididensità:1. bassaDensità:PELD 2. AltaDensità:PEHD
Polyethylenetubecanbeusedwithinarestrictiverangeoftemperaturesfrom-10°Cto+60°C.C.EcotubesmadeofPolyethyleneforpneumaticapplicationsareproposedwithtwolevelofdensity:1. LowDensity:PELD 2. HighDensity:PEHD
1. PE LD
TEMPERATURA D’USOTEMPERATURE RANGE
Da-10°Ca+60°C
From-10°Cto+60°C
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
PELD – 6 X 1 mm – C.ECO – 5385 - 10 - 173 - 12:30øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesternosono:Dal3mmal10mm:+/-0,07mmDal11mmal22mm:+/-0,1mm
Toleranceonexternaldiameter:From3mmto10mm:+/-0,07mmFrom11mmto22mm:+/-0,1mm
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
8 mm
10 mm
12 mm
12 mm
12 mm
14 mm
16 mm
2 mm
4 mm
6 mm
8 mm
10 mm
9 mm
8 mm
10 mm
12 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
2 mm
2 mm
2 mm
18 mm
30 mm
40 mm
60 mm
80 mm
65 mm
60 mm
80 mm
100 mm
63 bar
38 bar
27 bar
21 bar
17 bar
27 bar
38 bar
32 bar
27 bar
21 bar
13 bar
9 bar
7 bar
6 bar
9 bar
13 bar
11 bar
9 bar
% delle press.
Temp.
100%83% 72% 64% 57%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
MaterialeRawmaterial
PE
32
2. PE HD
GAMMA COLORICOLOUR RANGE
PerilPELD:ForPELD:
LaCastelloItaliaconunminimod’ordinedi3.000mèingradodioffrirvitubidicoloripersonalizzatisecondotabellaRAL.CastelloItaliauponrequestcanoffercustomcoloursfollowingRALspecificationforaminimumdeliveryof3.000m.
NaturaleNatural
Neroblack
Azzurrobluesky
NT NR AZRossoRed
gialloYellow
Verdegreen
RO gI VE
TEMPERATURA D’USOTEMPERATURE RANGE
Da-10°Ca+60°C
From-10°Cto+60°C
LUNGHEZZA MATASSAROLL SIZE
standard100mt.Altriavvolgimentisurichiesta.
standard100mt.Otherlenghtsuponrequest.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllarelatabellaapagina65.
Checkthetableatpage65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film dipolietilene.Per lealtre tipologiedipackagingconsultarelapagina61.
Ourstandardiswithpolyethylenefilm around. For other kinds ofpackagingcheckpage61.
TOLLERANZATOLERANCE
Lenostretolleranzesuldiametroesternosono:Dal3mmal12mm:+/-0,1mm
Toleranceonexternaldiameter:From3mmto12mm:+/-0,1mm
MARCATURA MARkING
Lanostramarcaturastandardè:Ourstandardmarkingis:
PEHD – 8 X 1 mm – C.ECO – 1109 - 08 - 164 - 15:33MaterialeRawmaterial
øEsternoxspessoreøExternalxThickness
NomeprodottoProductname
Numerodilottobatchnumber
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23 °C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
8 mm
8 mm
10 mm
12 mm
2,5 mm
4 mm
5 mm
6 mm
8 mm
9 mm
0,75 mm
1 mm
1,5 mm
1 mm
1 mm
1,5 mm
20 mm
35 mm
40 mm
40 mm
40 mm
70 mm
115 bar
100 bar
115 bar
71 bar
56 bar
71 bar
38 bar
33 bar
38 bar
24 bar
19 bar
24 bar
GAMMA COLORICOLOUR RANGE
PerilPEHD:ForPEHD: Naturale
NaturalAzzurrobluesky
NT AZ
La Castello Italia con un minimod’ordine di 3.000 m è in gra-do di offrirvi tubi di colori perso-nalizzati secondo tabella RAL.
Castello Italiauponrequestcanof-fer custom colours following RALspecificationforaminimumdeliveryof3.000m.
PE
33
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
Ivaloriedicoefficientiindicatinelletabelleriportatesuquestocatalogosonopuramenteindicativi,nonsonovincolantiperCastelloItaliasrlenoncomportanoelementodiresponsabilitàacaricodellastessaincasodidifformitàrispettoadettetabelle,ovveroincasodierroneoimpiegodelprodottodapartedelCliente.
Thevaluesandcoefficientscontainedinthisdocumentareforinformationonlyandshallinnoeventbeheldtoconstituteorimplyanywarranty,undertaking,expressorimpliedcommitment.NoliabilitywhatsoevercanbeacceptedbyCastelloItaliasrlwithrespecttodifferencetothevaluesreportedinthetablesormisusebytheCustomeroftheproducts.
- POLIAMMIDE 12 ATEX POLYAMIDE 12 ATEX
I tubi C.Esd in Poliammide 12 HIPHL nascono dall’introduzione delle nanotecnologie nei materiali plastici permettendo di creare un tubo antistatico flessibile per il passaggio dell’aria ed altri fluidi.Questi tubi sono certificati ATEX II 2 G/D. Le loro principali applicazioni sono:• Ambienti esplosivi (ATEX)• Trasporto della benzina (automotive)• Trasporto di fluidi infiammabili
C.Esd tubes are developed using the latest nanotechnology in techno-polymer. This tube, antistatic and flexible, can be used in pneumatic and fluid transfer applications such as:• Explosive environment (ATEX)• Fuel line (automotive)• Flammable fluid transferC.Esd is certificated ATEX II 2 G/D.
TOLLERANZATOLERANCE
Le nostre tolleranze sul diametro esterno sono:Dal 3 mm al 10 mm : +/- 0,10 mmDal 11 mm al 22 mm : +/- 0,15 mm
Tolerance on external diameter: From 3 mm to 10 mm : +/- 0,10 mmFrom 11 mm to 22mm : +/- 0,15 mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da -60° C a +130° C
From -60° C to +130° C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.
Check the table at page 65.
Caratteristica / Characteristic Metodo Test / Test Method Unità di misura / Unit
Modulo elastico E / E Modulus
Carico di rottura / Tensile strength @ break
Allungamento a rottura / Elongation @ break
Resistenza all’urto (+23°C) / Impact strength (+23°C)
Durezza Shore D / Hardness Shore D
ISO 527
ISO 527
ISO 527
ISO 179/2-1eU
ISO 868
350
35
>50
no break
63
MPa
MPa
%
kJ/m2
-
SCHEDA TECNICA DELLA MATERIA PRIMAMATERIAL TECHNICAL DATA SHEET
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
4 mm
4 mm
6 mm
8 mm
10 mm
12 mm
14 mm
2,5 mm
2,7 mm
2 mm
4 mm
6 mm
8 mm
10 mm
12 mm
0,75 mm
0,65 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1 mm
20 mm
25 mm
15 mm
35 mm
40 mm
60 mm
85 mm
85 mm
78 bar
65 bar
112 bar
67 bar
48 bar
37 bar
31 bar
26 bar
26 bar
22 bar
37 bar
22 bar
16 bar
12 bar
10 bar
9 bar
Resistività di superficiespecifica IEC 60093
Specific surface resistivityIEC 60093
106 Ohm
106 Ohm
106 Ohm
106 Ohm
106 Ohm
106 Ohm
106 Ohm
106 Ohm
34
PA
12
ATE
X
LUNGHEZZA MATASSAROLL SIZE
Standard 100 mt.Altri avvolgimenti su richiesta.
Standard 100 mt.Other lenghts upon request.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
MARCATURA MARkING
La nostra marcatura standard è:Our standard marking is:
- 8 X 1 mm - PA 12 HIPHL - C.ESD - ATEX II 2 G/D - 1109 - 08 - 164 - 15:33Materiale
Raw materialø Esterno x Spessoreø External x Thickness
Nome prodottoProduct name
Numero di lottoBatch number
GAMMA COLORICOLOUR RANGE
Per il PA12 ATEX:For PA12 ATEX: Nero
Black
NR
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.
100% 87%74% 64% 57%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
35
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
Tubi SpecialiSpecial Tubes
PA
12
ATEX
- TUBO IN CO - POLIAMMIDE CO - POLYAMIDE TUBE
GAMMA COLORICOLOUR RANGE
Per il C.Hot:For C.Hot:
NeroBlack
NR
LUNGHEZZA MATASSAROLL SIZE
Standard 100 mt.Altri avvolgimenti su richiesta.
Standard 100 mt.Other lenghts upon request.
TEMPERATURA D’USOTEMPERATURE RANGE
Da -60°C a +150°CFrom -60°C to +150°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.Check the table at page 65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
MARCATURA MARkINGLa nostra marcatura standard è:Our standard marking is:
- 8x1mm - Copa - c.hot-7457 - 10 - 121 - 13:30Materiale
Raw materialø Esterno x Spessoreø External x Thickness
Nome prodottoProduct name
Numero di lottoBatch number
36
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
8 mm
10 mm
12 mm
2,5 mm
4 mm
6 mm
8 mm
10 mm
0,75 mm
1 mm
1 mm
1 mm
1 mm
20 mm
35 mm
40 mm
60 mm
85 mm
31 bar
27 bar
19 bar
15 bar
12 bar
92 bar
80 bar
57 bar
44 bar
36 bar
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.
100% 90%60% 50% 40%
0%20%40%60%80%
100%120%
20°C 60°C 100°C 120°C 140°C
Questo innovativo tubo è realizzato grazie all’applicazione di ma-terie prime usate nella produzione di tubi per il settore automo-tive. I suoi principali punti di forza sono: • Resistenza, in continuo, a una temperatura di 150°C • Perfetto aggancio ai raccordi au-tomatici (rispetto ad un tubo in PTFE) • Ottimo raggio di curva-tura • Ottimo per la realizzazione di spirali e pezzi termoformati.This innovative tube has been developed for very stringent automotive and pneumatic applications. Its main properties are: • Long term tem-perature resistance 150°C • Suitable for push-in fittings (better than PTFE tubes) • Very good bending radius • Suitable for thermoforming parts such as spirals.
TOLLERANZATOLERANCELe nostre tolleranze sul diametro esterno, secondo DIN 73378, sono:Dal 3 mm al 10 mm : +/- 0,10 mmDal 11 mm al 22 mm : +/- 0,15 mmSu richiesta possiamo offrirvi tubi ad alta precisione con le seguenti tolleranze:Dal 3 mm al 10 mm : +/- 0,03 mmDal 11 mm al 22 mm : +/- 0,05 mmTolerance on external diameter as per DIN 73378 Norm:From 3 mm to 10 mm : +/- 0,10 mmFrom 11 mm to 22 mm : +/- 0,15 mmUpon request we could deliver high precision tubes at this tolerance:From 3 mm to 10 mm : +/- 0,03 mmFrom 11 mm to 22 mm : +/- 0,05 mm
NaturaleNatural
NTAzzurroBlue Sky
AZRossoRed
RO
CO
- P
OLI
AM
MID
E
TUB
O A
NTIS
CIN
TILLA
Questo tubo è stato studiato per le applicazioni in cui scintille, trucioli caldi, schizzi di liquidi ad alta tempe-ratura e più in generale le fonti di calore possono andare a danneggiare i tubi in poliammide monostrato. La speciale calza in poliestere (PET) ignifugato e la ricopertura in poliuretano autoestinguente hanno il solo compito di proteggere il tubo interno in PA12. Questo rivestimento può essere facilmente rimosso o fatto scorrere, consentendo di inserire il tubo interno in un raccordo automatico. I tubi C.Spark sono particolar-mente indicati nell’automazione pneumatica degli impianti di saldatura data la loro maggiore leggerezza rispetto alle tubazioni in gomma.
This tube has been especially developed for difficult environment where heat produced either by welding sparks or by hot liquid drops could disturb the integrity of the inner tube in Polyamide12. The special self-extinguishing Polyester (PET) sock combined with a fire proof Polyurethane fulfill the task of protecting the inner tube in Polyamide12. The sliding ability of the sock allows connection of the inner tube into push-in fittings. The C.Spark tubes are recommended for use in automated welding lines because of their lighter weight compared to traditional rubber tubes.
GAMMA COLORICOLOUR RANGE
Per il C.Spark:For C.Spark:
37
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
- TUBO ANTISCINTILLA ANTI SPARK - TUBE
NeroBlack
NRGrigioGray
guainadi protezione
TEMPERATURA D’USOTEMPERATURE RANGE
Da -60° C a +130°CFrom -60° C to +130°C
LUNGHEZZA MATASSAROLL SIZE
Standard in matasse 50 mt.Altri avvolgimenti su richiesta.
Standard 50 mt.Other lenghts upon request.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.Check the table at page 65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.
100% 87%74% 64% 57%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
MARCATURA MARkING
La nostra marcatura standard è:Our standard marking is:
C.spark - 8 X 6 mm - tubo - antiscintilla - anti spark hoseø Esterno x Spessoreø External x Thickness
Nome prodottoProduct name
MaterialeRaw material
0 Esterno0 External
4 mm
6 mm
8 mm
10 mm
0 Interno0 Inside
2,5 mm
4 mm
6 mm
8 mm
SpessoreThickness
0,75 mm
1 mm
1 mm
1 mm
Pressione esercizio (a 23°C)Working pressure (at 23°C)
31 bar
27 bar
19 bar
15 bar
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
92 bar
80 bar
57 bar
44 bar
DATI TUBO INTERNOINTERNAL TUBE DATA
- TUBI PTFE PTFE TUBES
I tubi in PTFE grazie alle caratteristiche del legame carbonio-fluoro sono consigliabili per le applicazioni in cui sono richieste:• Elevate temperature di utilizzo: -200°C a + 260°C• Resistenza agli agenti chimici• Basso coefficiente di attrito• Eccellenti proprietà dielettriche• Non infiammabile (UL 94 V0)• Buone proprietà meccaniche• Non invecchia• Inalterabile• Ottima resistenza all’umidità ed ai raggi U.V.• Non è tossico
Combination of Carbon and fluor allows this material to show excellent properties such as:• Broad range of temperature: -200°C to + 260°C• Perfect chemical resistance to all corrosive substances• Low friction coefficient• Remarkable dielectrical properties• Self-extinguishing (UL 94 V0)• Good mechanical properties• Unalterable• Slow ageing• Excellent hydrolysis and UV resistance• Non toxic
PTF
E
Caratteristica / Characteristic Metodo Test / Test Method Unità di misura / Unit PTFE
Peso specifico / Specific gravity
Punto di fusione / Melting point
Modulo a trazione / Tensile modulus
Fattore di dissipazione dielettrica / Dieletric dissipation factor
Durezza Shore D / Hardness Shore D
g/cm3
ISO 3416C
D790
D150@10 (10x2) hz
D2240
2,15
327
90000
0,0002
60
D792
°C
PSI
-
Shore D
SCHEDA TECNICA DELLA MATERIA PRIMAMATERIAL TECHNICAL DATA SHEET
TEMPERATURA D’USOTEMPERATURE RANGE
Da -200°C a +260°C
From -200°C to +260°C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.
Check the table at page 65.
TOLLERANZATOLERANCE
Le nostre tolleranze sul diametro esterno sono:Dal 3 mm al 14 mm : +/- 0,20 mmDal 15 mm al 22 mm : +/- 0,30 mm
Tolerance on external diameter: From 3 mm to 14 mm : +/- 0,20 mmFrom 15 mm to 22 mm : +/- 0,30 mm
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
PesoWeight
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
8 mm
10 mm
12 mm
14 mm
15 mm
2 mm
4 mm
6 mm
8 mm
10 mm
12 mm
12,5 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1 mm
1,25 mm
37 g/m
51 g/m
66 g/m
80 g/m
95 g/m
109 g/m
141 g/m
76 bar
54 bar
42 bar
35 bar
29 bar
25 bar
28 bar
25 bar
18 bar
14 bar
12 bar
10 bar
8 bar
9 bar
38
LUNGHEZZA MATASSAROLL SIZE
Standard 50 mt.Altri avvolgimenti su richiesta.
Standard 50 mt.Other lenghts upon request.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
MARCATURA MARkING
Questo tipo di tubo non è marcato.
This kind of tube is not marked.
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.
100%
50%35% 30%
10%0%
20%40%60%80%
100%120%
20°C 50°C 100°C 150°C 200°C
PTFE
GAMMA COLORICOLOUR RANGE
Per il PTFE:For PTFE:
NTAzzurroBlue Sky
AZNaturaleNatural
39
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
ALTRI TUBI IN FLUORO POLIMERO FEP & PFAOTHER TUBES IN FLUOROPOLYMER FEP & PFA
PFA (PERFLUOROALCOSSI) & FEP (ETILENE PROPILENE FLUORORATO)Il PFA e il FEP sono polimeri termoplastici interamente fluororati con una struttura molecolare e chimica molto simile al PTFE.Il PFA risulta essere il più puro tra il PTFE e il FEP, e quindi idoneo alle applicazioni più restrittive, mentre il FEP risulta essere leg-germente meno resistente al calore rispetto agli altri due fluoropolimeri: da -60°C a +205°C. Il FEP e il PFA si presentano con una colorazione trasparente.
PFA (PERFLUOROALkOXY) & FEP (FLUORINATED ETHYLENE PROPYLENE)FEP and PFA are entirely fluorinated thermoplastics and they have a molecular structure and physical, electrical and chemical properties very similar to those of PTFE. Compared to PTFE and FEP, PFA is a more resistant and pure material, it is able to meet stricter needs. FEP mainly differs from PTFE and PFA because of the working temperatures that are slightly lower than theirs; to be more precise: from -60° C to +205° C. Generally FEP and PFA have transparent coloration.
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
8 mm
10 mm
2mm
4 mm
6 mm
8 mm
1 mm
1 mm
1 mm
1 mm
20 mm
33 mm
47 mm
60 mm
25 bar
18 bar
13 bar
10 bar
75 bar
56 bar
40 bar
30 bar
PA
11
/P
A1
2 - PA11/PA12 SELF-EXTINGUISING
PA11/PA12 SELF-EXTINGUISING
I tubi C.Flam in PA11/PA12 consentono di ritardare la fiamma in caso di incendio.Questi tubi vengono classificati UL94 V2, sono sia ROHS Free che privi di alogeni e vengono prodotti nella sola colorazione azzurra.
C.Flam PA11/PA12 fireproof tubes are capable of retarding the flame in case of fire.They are classified UL94 V2, they are ROHS Free and halogen free and they are available only in blue sky colour.
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
6 mm
8 mm
10 mm
12 mm
12 mm
15 mm
18 mm
22 mm
24 mm
4 mm
6 mm
8 mm
10 mm
9 mm
12 mm
15 mm
18 mm
20 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
1,5 mm
1,5 mm
2 mm
2 mm
40 mm
45 mm
85 mm
90 mm
75 mm
105 mm
200 mm
220 mm
250 mm
96 bar
69 bar
53 bar
44 bar
69 bar
53 bar
44 bar
48 bar
44 bar
32 bar
23 bar
18 bar
15 bar
23 bar
18 bar
15 bar
16 bar
15 bar
GAMMA COLORICOLOUR RANGE
Per il PA11/PA12 SELF-EXTINGUISHING:For PA11/PA12 SELF-EXTINGUISHING: Azzurro
Blue Sky
AZ
TEMPERATURA D’USOTEMPERATURE RANGE
Da -60°C a +130°CFrom -60°C to +130°C
LUNGHEZZA MATASSAROLL SIZE
Standard 100 mt.Altri avvolgimenti su richiesta.
Standard 100 mt.Other lenghts upon request.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.Check the table at page 65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
TOLLERANZATOLERANCE
Le nostre tolleranze sul diametro esterno sono:Dal 3 mm al 10 mm : +/- 0,10 mmDal 11 mm al 22 mm : +/- 0,15 mm
Tolerance on external diameter: From 3 mm to 10 mm : +/- 0,10 mmFrom 11 mm to 22 mm : +/- 0,15 mm
MARCATURA MARkING
La nostra marcatura standard è:Our standard marking is:
- C.FLAm - 15 X 1,5 mm - PA 11 - SELF EXTINGUISHING - 4120 - 08 - 230 - 08:10Materiale
Raw materialø Esterno x Spessoreø External x Thickness
Nome prodottoProduct name
Numero di lottoBatch number
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE% delle press.
Temp.
100%70% 65%
52% 45%
0%20%40%60%80%
100%120%
20°C 30°C 40°C 50°C 60°C
40
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
- TUBI PVDF PVDF TUBES
I tubi C.Tech sono realizzati in PVDF. Questo polimero florurato ha come principale caratteristica la re-sistenza agli agenti chimici e rispetto al PTFE ha caratteristiche meccaniche superiori e non subisce la deformazione sotto il peso.
C.Tech tubes are made in PVDF. This kind of fluorpolymer has a good chemical resistance, excellent mechanical properties in comparison of PTFE and good resistance to creeping.
PV
DF
GAMMA COLORICOLOUR RANGE
Per il PVDF:For PVDF: Bianco
White
BI
TEMPERATURA D’USOTEMPERATURE RANGE
Da -40°C a -100°CFrom -40°C to -100°C
LUNGHEZZA MATASSAROLL SIZE
Standard 100 mt.Altri avvolgimenti su richiesta.
Standard 100 mt.Other lenghts upon request.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.Check the table at page 65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
TOLLERANZATOLERANCELe nostre tolleranze sul diametro esterno sono:Dal 3 mm al 8 mm : +/- 0,05 mmDal 9 mm al 12 mm : +/- 0,1 mmSullo spessore: +/- 0,05 mmTolerance on external diameter: From 3 mm to 8 mm : +/- 0,05 mmFrom 9 mm to 12 mm : +/- 0,10 mmOn the thickness wall: +/- 0,05 mm
MARCATURA MARkING
La nostra marcatura standard è:Our standard marking is:
- C.TECH - 6 X 1 mm - PVDF - 1109 - 08 - 164 - 15:33Materiale
Raw materialø Esterno x Spessoreø External x Thickness
Nome prodottoProduct name
Numero di lottoBatch number
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
% delle press.
Temp.
100%70%
55% 50% 45%25%
0%20%40%60%80%
100%120%
20°C 30°C 40°C 60°C 80°C 90°C
0 Esterno0 External
0 Interno0 Inside
SpessoreThickness
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C) Burst pressure (at 23°C)
4 mm
6 mm
8 mm
10 mm
12 mm
2 mm
4 mm
6 mm
8 mm
9 mm
1 mm
1 mm
1 mm
1 mm
1,5 mm
20 mm
35 mm
40 mm
60 mm
85 mm
167 bar
100 bar
71 bar
56 bar
45 bar
56 bar
33 bar
24 bar
19 bar
15 bar
Raggio di curvaturaBending Radius
41
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
C.Twenty è un tubo in poliuretano retinato molto flessibile. Ha una grande resistenza all’abrasione e una flessibilità 5 volte superiore a quella del PVC e grazie alla retinatura in poliestere offre una pres-sione di esercizio di 20 bar.
C.Twenty is a flexible braided hose in polyurethane. It shows very good abrasion resistance and a flexibility 5 times better than PVC and thanks to its polyester braiding the working pressure reaches 20 bar.
42
TEMPERATURA D’USOTEMPERATURE RANGE
Da -20°C a +60°CFrom -20°C to +60°C
APPLICAZIONI PRINCIPALIMAIN APPLICATIONS
Utensili pneumatici, verniciatura, aerografi, soffiaggio etc.Pneumatic tools, spray guns, painting machineries.
GAMMA COLORICOLOUR RANGE
Per il Poliuretano retinato:For Braided Polyurethane: Blu
Dark Blue
BL
0 Esterno0 External
10 mm
12 mm
15 mm
19 mm
23 mm
0 Interno0 Inside
6 mm
8 mm
10 mm
13 mm
16 mm
1/4 Pollici / Inches
5/16 Pollici / Inches
3/8 Pollici / Inches
1/2 Pollici / Inches
5/8 Pollici / Inches
PesoWeight
65 gr/mt
85 gr/mt
130 gr/mt
195 gr/mt
280 gr/mt
Lunghezza rotoliCoil length
100 mt
100 mt
100 mt
100 mt
100 mt
Non sottoporre alla pressione per lungo tempo.Do not keep under pressure for long periods of time.
Pressione esercizio (a 23°C)Working pressure (at 23°C)
20 bar
20 bar
20 bar
20 bar
20 bar
PU - POLIURETANO RETINATO
BRAIDED POLYURETHANE
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
60 bar
60 bar
60 bar
60 bar
60 bar
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
PesoWeight
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Lunghezza rotoliCoil length
0 Esterno0 External
10 mm
11 mm
12 mm
13 mm
14 mm
15 mm
15 mm
16 mm
18 mm
19 mm
21 mm
22 mm
26 mm
29 mm
33 mm
40 mm
42 mm
45 mm
48 mm
50 mm
55 mm
64 mm
5/32 Pollici / Inches
3/16 Pollici / Inches
1/4 Pollici / Inches
5/16 Pollici / Inches
5/16 Pollici / Inches
11/32 Pollici / Inches
3/8 Pollici / Inches
3/8 Pollici / Inches
15/32 Pollici / Inches
1/2 Pollici / Inches
19/32 Pollici / Inches
5/8 Pollici / Inches
3/4 Pollici / Inches
7/8 Pollici / Inches
1 Pollici / Inches
1 3/16 Pollici / Inches
1 1/4 Pollici / Inches
1 3/8 Pollici / Inches
1 1/2 Pollici / Inches
1 9/16 Pollici / Inches
1 3/4 Pollici / Inches
2 Pollici / Inches
0 Interno0 Inside
4 mm
5 mm
6 mm
8 mm
8 mm
9 mm
10 mm
10 mm
12 mm
13 mm
15 mm
16 mm
19 mm
22 mm
25 mm
30 mm
32 mm
35 mm
38 mm
40 mm
45 mm
50 mm
85 gr/mt
95 gr/mt
110 gr/mt
110 gr/mt
130 gr/mt
145 gr/mt
130 gr/mt
155 gr/mt
180 gr/mt
190 gr/mt
220 gr/mt
230 gr/mt
320 gr/mt
355 gr/mt
465 gr/mt
710 gr/mt
730 gr/mt
810 gr/mt
860 gr/mt
910 gr/mt
1020 gr/mt
1580 gr/mt
17 bar
17 bar
20 bar
15 bar
15 bar
15 bar
15 bar
15 bar
12 bar
12 bar
10 bar
10 bar
8 bar
8 bar
8 bar
5 bar
5 bar
5 bar
5 bar
5 bar
4 bar
4 bar
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
50 mt
50 mt
50 mt
25/50 mt
25/50 mt
25/50 mt
25/50 mt
25 mt
25 mt
25 mt
Non utilizzare con acqua calda. Non sottoporre alla pressione per lungo tempo.Do not use with hot water. Do not keep under pressure for long periods of time.
- PVC RETINATO BRAIDED PVC
Il C.kristal è un tubo in PVC rinforzato con retinatura tessile in poliestere ad alta tenacità. Questo tubo viene realizzato nella ver-sione atossica secondo la normativa DM 21/3/73, e successivi aggiornamenti, direttiva CEE 907128 e modifiche.
C.kristal is a transparent polyeser braided PVC hose, extremely flexible, chemical and pressure resistant. Available in non-toxic ver-sion according to Italian standards DM 21/3/73 and EEC directi-ve 90/128 and subsequent updates.
PV
C
43
TEMPERATURA D’USOTEMPERATURE RANGE
Da -10°C a +50°CFrom -10°C to +50°C
APPLICAZIONI PRINCIPALIMAIN APPLICATIONS
Impianti chimici, apparecchiature pneumatiche, sistemi di pulitura automati-ca, travaso di acidi, sali, basi, trasporto di agenti chimici aggressivi, industria alimentare ed aria compressa.Chemical plants, cleaning systems, pneumatic machinery, level gages, acid, salt and base decanting, transport of chemical agents and compressed air, food industry.
GAMMA COLORICOLOUR RANGE
Per il PVC retinato:For PVC braided: Trasparente con la possibilità di colorazioni differenti della ricopertura esterna
o interna per lotti minimi di 3.000 m.Transparent with the possibility of other colours for the external or internal layer for a minimun delivery of 3.000 m.
TR
PV
C
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
44
- PVC CON SPIRALE METALLICA PVC WITH STEEL SPIRAL
Il C.Metal è un tubo atossico in PVC trasparente con spirale in ac-ciaio armonico zincato antischiacciamento adatto per l’aspirazione e mandata dei liquidi. Questo tubo risponde alla normativa DM 21/3/73 e CEE 90/128 e relativi aggiornamenti.
C.Metal is a very flexible non-toxic transparent PVC hose with im-pact and crush resistant galvanised steel spiral reinforcement. Smooth inside and outside surfaces. This hose is non-toxic according to Italian standards DM 21/3/73 et EEC 90/128 and following updates.
PV
C
0 Interno0 Inside
10 mm
12 mm
14 mm
16 mm
18 mm
20 mm
22 mm
25 mm
30 mm
32 mm
35 mm
38 mm
40 mm
45 mm
50 mm
60 mm
3/8 Pollici / Inches
1/2 Pollici / Inches
9/16 Pollici / Inches
5/8 Pollici / Inches
23/32 Pollici / Inches
25/32 Pollici / Inches
7/8 Pollici / Inches
1 Pollici / Inches
1 3/16 Pollici / Inches
1 1/4 Pollici / Inches
1 3/8 Pollici / Inches
1 1/2 Pollici / Inches
1 9/16 Pollici / Inches
1 3/4 Pollici / Inches
2 Pollici / Inches
2 3/8 Pollici / Inches
PesoWeight
160 gr/mt
180 gr/mt
230 gr/mt
270 gr/mt
300 gr/mt
340 gr/mt
380 gr/mt
500 gr/mt
600 gr/mt
650 gr/mt
750 gr/mt
800 gr/mt
930 gr/mt
1150 gr/mt
1450 gr/mt
1800 gr/mt
Pressione esercizio (a 23°C)Working pressure (at 23°C)
8 bar
8 bar
8 bar
8 bar
7 bar
7 bar
6 bar
6 bar
5 bar
5 bar
5 bar
4,5 bar
4,5 bar
4,5 bar
4 bar
4 bar
Lunghezza rotoliCoil length
60 mt
60 mt
60 mt
60 mt
60 mt
60 mt
60 mt
60 mt
60 mt
60 mt
60 mt
30 mt
30 mt
30 mt
30 mt
30 mt
Raggio di curvaturaBending Radius
20 mm
25 mm
30 mm
35 mm
40 mm
50 mm
55 mm
60 mm
70 mm
75 mm
80 mm
90 mm
95 mm
110 mm
125 mm
140 mm
SottovuotoVacuum
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
9 m H2o
8,5 m H2o
8,5 m H2o
3 mm
3 mm
3,2 mm
3,2 mm
3,2 mm
3,4 mm
3,6 mm
4 mm
4,2 mm
4,2 mm
4,5 mm
4,5 mm
4,7 mm
5 mm
5 mm
6 mm
Spessore pareteWall tickness
Non sottoporre alla pressione per lungo tempo.Do not keep under pressure for long periods of time.
TEMPERATURA D’USOTEMPERATURE RANGE
Da -15°C a +65°CFrom -15°C to +65°C
APPLICAZIONI PRINCIPALIMAIN APPLICATIONS
Aspirazione e mandata dei liquidi in agricoltura, edilizia, industria e su macchi-ne industriali ed agricole.Suction and delivery of liquids in agriculture, building and manufacturing industries. For all types of agricultural and industrial machineries.
GAMMA COLORICOLOUR RANGE
Per il PVC con spirale metallica:For PVC with steel spiral: Trasparente
Transparent
TR
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
45
- TUBO MONOSTRATO IN PVC Monolayer PVC Tube
C.Plast è un tubo in PVC monostrato in colorazione cristallina, atos-sico secondo la normativa DM 21/3/73 e direttiva CEE 90/128 e relativi aggiornamenti e modifiche.Questo tubo offre una ottima trasparenza, resistenza agli agenti chimici ed alta flessibilità in presenza di basse temperature.
C.Plast is a transparent high quality PVC hose, non-toxic, accor-ding to Ministerial Decree 21/3/73, EEC directive 90/128 and subsequent updates and modifications.This tube shows good transparency and high flexibility at low tem-peratures, as well as very strong resistance to chemical agents.
TEMPERATURA D’USOTEMPERATURE RANGE
Da -15°C a +65°CFrom -15°C to +65°C
APPLICAZIONI PRINCIPALIMAIN APPLICATIONS
Applicazioni industriali e nell’agricoltura fino al giardinaggio dove non sono richieste pressioni elevateIndustrial and agricultural applications (also in garden bricolage) where resistance to high pressure is not required.
Non utilizzare con acqua calda.Do not use with hot water
GAMMA COLORICOLOUR RANGE
Per il tubo in monostrato in PVC:For monolayer PVC tube: Trasparente (Verde, Rosso e Nero su richiesta)
Transparent (Green, Red and Black upon request)
TR
PVC
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
46
La Castello Italia con un minimo d’ordine di 5.000 m è in grado di offrirvi tubi di colori personalizzati.Castello Italia upon request can offer custom colours for a minimum delivery of 5.000 m.
0 Esterno0 External
7 mm
8 mm
9 mm
10 mm
12 mm
14 mm
17 mm
19 mm
22 mm
0 Interno0 Inside
4 mm
5 mm
6 mm
7 mm
8 mm
10 mm
12 mm
14 mm
16 mm
9/32 Pollici / Inches
3/16 Pollici / Inches
1/4 Pollici / Inches
9/32 Pollici / Inches
5/16 Pollici / Inches
3/8 Pollici / Inches
15/32 Pollici / Inches
9/16 Pollici / Inches
5/8 Pollici / Inches
PesoWeight
32 gr/mt
40 gr/mt
45 gr/mt
57 gr/mt
78 gr/mt
95 gr/mt
148 gr/mt
170 gr/mt
225 gr/mt
Lunghezza rotoliCoil length
200 mt
200 mt
200 mt
100 mt
100 mt
100 mt
100 mt
100 mt
100 mt
- TUBI GRANDI DIAMETRI LARGE DIAMETER TUBES
MARCATURA MARkING
La nostra marcatura standard è:Our standard marking is:
- 100 X 5 mm - PA 12 PHL - C.BEST - 4050 - 08 - 280 - 15:33ø Esterno x Spessoreø External x Thickness
MaterialeRaw material
Nome prodottoProduct name
Numero di lottoBatch number
TEMPERATURA D’USOTEMPERATURE RANGE
Da -60° C a +130° CFrom -60° C to +130° C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.Check the table at page 65.
GAMMA COLORICOLOUR RANGE
Per il PA12 PHL:For PA12 PHL:
NT
La Castello Italia con un minimo d’ordine di 3.000 m è in grado di offrirvi tubi di colori personalizzati secondo tabella RAL.Castello Italia upon request can offer custom colours following RAL specification for a minimum delivery of 3.000 m.
NaturaleNatural
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
% delle press.
Temp.
100% 87%74% 64% 57%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
0 Esterno0 External
41 mm
43 mm
51 mm
54,5 mm
61 mm
63 mm
65 mm
70 mm
70 mm
70 mm
80 mm
80 mm
80 mm
90 mm
100 mm
110 mm
0 Interno0 Inside
34 mm
37 mm
44 mm
46,5 mm
53 mm
55 mm
57 mm
62 mm
61 mm
60 mm
73 mm
72 mm
70 mm
80 mm
90 mm
98 mm
SpessoreThickness
3,5 mm
3 mm
3,5 mm
4 mm
4 mm
4 mm
4 mm
4 mm
4,5 mm
5 mm
3,5 mm
4 mm
5 mm
5 mm
5 mm
6 mm
TUBI GRANDI DIAM
ETRI
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
47
I tubi grandi diametri sono realizzati in PA12 PHL e vengono impiegati in impianti pneumatici dove sono necessari grandi flussi di aria o fluidi a basse pressioni oppure come tubo sem-plice più flessibile e leggero rispetto all’ acciaio o al ferro.
The “Large Diameter” tubes are made of PA12 PHL and they are used in pneumatic system when the end user needs more flow without increasing the pressure. This kind of tubes is also more flexible and light then steel and it could be used like a normal tube in mechanical application.
- POLIAMMIDE 12 POLYAMIDE 12
I tubi C.Multi vengono realizzati attraverso l’impiego dei tubi C.Best.Questa tipologia di prodotto trova un impiego sia nell’automazione pneumatica che nel mercato automotive dove si vuole mantenere compatto ed unito il fascio di tubi.La fase di assemblaggio dei tubi avviene in modo elicoidale con una ricopertura a guaina di poliuretano o PVC resistente ai raggi UV e agli agenti chimici.Su richiesta la nostra azienda produce anche multitubi con altri ma-teriali come: C.Flex, C.Eco e C.Chem e con l’inserimento aggiuntivo di cavi elettrici.
C.Multi Tubes are produced using C.Best tubes.These products are used in industrial automation as well as in auto-motive market where tubes space is limited.Tubes are assembled in spiral fashion and protected by a black po-lyurethane or PVC sheath, resistant to UV and chemical agents. Upon request our company could produce also multitubes with other materials such as: C.Flex, C.Eco, C.Chem and electric cables can be included.
PA
12
0 Esterno0 External
0 Interno0 Inside
n° tubin° tubes
Pressione esercizio (a 23°C)Working pressure (at 23°C)
Pressione scoppio (a 23°C)Burst pressure (at 23°C)
4 mm
6 mm
8 mm
2,7 mm
4 mm
6 mm
2 - 3 - 4 - 7 - 12 mm
2 - 3 - 4 - 7 - 12 mm
2 - 3 mm
23 bar
27 bar
30 bar
77 bar
90 bar
68 bar
TOLLERANZATOLERANCE
Le nostre tolleranze per i tubi interni sono le medesime dei tubi lineari.
The internal tubes have the same tollerances as the linear tubes.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.
Check the table at page 65.
48
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
- SPIRALI COILS
Con i tubi C.Multi la Castello Italia realizza spirali di diverse forme e misure dedicate al settore della pneumatica industriale.Grazie alla torsione dei tubi all’interno della guaina si possono realizzare molti movimenti senza che si verifichino stress sia ai tubi che alla ricopertura.
With C.Multi tubes Castello Italia produces also coils for industrial automation market. Thanks to their special construction, our coils can resist a lot of solicitations without stress for tubes and PVC sheath.
SP
IRA
LI
0,65 mm 30 mm4 mm 2,7 mm
1 mm 50 mm6 mm 4 mm
1 mm 70 mm8 mm 6 mm
7,5 mt114 cm15 mt
7,5 mt100 cm15 mt
7,5 mt118 mm15 mt
TOLLERANZATOLERANCE
Le nostre tolleranze per i tubi interni sono le medesime dei tubi lineari.
The internal tubes have the same tollerances as the linear tubes.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.
Check the table at page 65.
49
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
MultitubiM
ultitubes
- POLIAMMIDE 12 POLYAMIDE 12
Le spirali realizzate in C.Best PA12 garantiscono un’eccezionale memoria elastica e consentono all’operatore di svolgere i propri lavori in massima libertà.La Castello Italia, oltre alle spirali di dimensione standard, è a dispo-sizione dei propri clienti per realizzare prodotti su misura per le esi-genze e gli impieghi più particolari.
C.Best PA12 coils ensure an excellent elastic memory and let the operator work freely. In case of special needs outside the standard range of coils, Castello Italia is at complete disposal to manufacture customized items.
6 mt360 mm10 mt
9 mt550 mm15 mt
17 mt1100 mm30 mt
6 mt290 mm10 mt
9 mt430 mm15 mt
17 mt870 mm30 mt
4,5 mt230 mm7,5 mt
6 mt305 mm10 mt
7 mt360 mm12 mt
9 mt455 mm15 mt
17 mt910 mm30 mt
4,5 mt230 mm7,35 mt
6 mt305 mm10 mt
7 mt360 mm12 mt
9 mt455 mm15 mt
17 mt910 mm30 mt
4,5 mt245 mm7,35 mt
6 mt330 mm10 mt
7 mt390 mm12 mt
9 mt490 mm15 mt
17 mt990 mm30 mt
6 mt290 mm10 mt
9 mt430 mm15 mt
17 mt870 mm30 mt
7,5 mt465 mm15 mt
15 mt930 mm30 mt
1 mm 30 mm4 mm 2 mm
1 mm 60 mm6 mm 4 mm
0,825 mm 80 mm8 mm 6,35 mm
1 mm 80 mm8 mm 6 mm
1 mm 90 mm10 mm 8 mm
1 mm 120 mm12 mm 10 mm
1,5 mm 160 mm15 mm 12 mm
PA
12
Per tutte le informazioni tecniche vedere scheda C.Best e C.Bio.See C.Best and C.Bio data sheet for technical information.
50
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
- POLIAMMIDE 6 POLYAMIDE 6
Le spirali in PA6 sono ottime per quanto concerne la memoria ela-stica e le loro prestazioni meccaniche. Questa tipologia di prodotto trova come principale applicazione i kit per l’hobbistica e l’automazione pneumatica industriale dove non sono richieste le più elevate prestazioni del Poliammide 12.
Coils in PA6 are excellent for their elastic memory and for their me-chanical performance.Their main applications are in the kit for hobby activities and indu-strial automation, where the more resistant Polyamide 12 is not required.
PA
6
Per tutte le informazioni tecniche vedere scheda C.Six.See C.Six data sheet for technical information.
3 mt150 mm5 mt
4,5 mt230 mm7,5 mt
6 mt305 mm10 mt
7 mt360 mm12 mt
9 mt455 mm15 mt
17 mt910 mm30 mt
4,5 mt245 mm7,35 mt
6 mt330 mm10 mt
7 mt390 mm12 mt
9 mt490 mm15 mt
17 mt990 mm30 mt
6 mt290 mm10 mt
9 mt430 mm15 mt
17 mt870 mm30 mt
0,825 mm 80 mm8 mm 6,35 mm
1 mm 90 mm10 mm 8 mm
1 mm 120 mm12 mm 10 mm
51
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
Spirali
Coils
- POLIURETANOPOLYurEThANE
Le spirali in poliuretano della Castello Italia vengono realizzate in tubi C.Flex, C.Kolor e C.Star.Grazie alla grande morbidezza e flessibilità del poliuretano le spirali offrono la massima maneggevolezza e una buona resistenza all’abra-sione e all’urto.Le nostre spirali possono essere consegnate sia raccordate che senza raccordo e siamo a disposizione dei clienti per studiare prodot-ti su misura al di fuori della nostra gamma standard.
Coils in Polyurethane are produced with linear tubes C.Flex, C.Kolor and C.Star.These products guarantee excellent handling and good resistance to abrasion and shock.Castello Italia offers the possibility to deliver the coils with or without fittings and is at complete disposal to manufacture customized items.
Pu
4 mt380 mm6 mt
6 mt570 mm9 mt
8 mt760 mm12 mt
4 mt310 mm6 mt
6 mt480 mm9 mt
8 mt640 mm12 mt
4 mt310 mm6 mt
6 mt480 mm9 mt
8 mt640 mm12 mt
4 mt330 mm6 mt
6 mt500 mm9 mt
8 mt680 mm12 mt
4 mt320 mm6 mt
6 mt490 mm9 mt
8 mt660 mm12 mt
4 mt320 mm6 mt
6 mt490 mm9 mt
8 mt660 mm12 mt
1 mm 25 mm6 mm 4 mm
1,25 mm 40 mm8 mm 5,5 mm
1,5 mm 40 mm8 mm 5 mm
1,5 mm 50 mm10 mm 7 mm
2 mm 60 mm12 mm 8 mm
1,5 mm 60 mm12 mm 9 mm
Per tutte le informazioni tecniche vedere scheda C.Flex e C.Kolor.See C.Flex and C.Kolor data sheet for technical information.
52
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
&PA12 & PA11
I tubi C.Best e C.Bio monostrato sono utilizzati non solo nella pneumatica indu-striale ma anche nei sistemi frenanti di motrici e rimorchi.Questi tubi sono realizzati utilizzando le più sofisticate tecnologie in campo d’estrusione e controllo dimensionale in modo da garantire sempre migliori tolleranze per l’inserimento nei raccordi automatici. Questi tubi vengono avvolti grazie ad una macchina completamente automatica in grado di confezionare matasse di diversa lunghezza a seconda delle esigenze del cliente finale.In aggiunta la nostra azienda è in grado di marcare il tubo anche con tacche di profondità secondo il passo del raccordo (previo comunicazione della tipologia di raccordo utilizzato) al fine di poter aiutare l’operatore nel perfetto montaggio dell’impianto frenante.
C.Best and C.Bio monolayer tubes can only be used not only in industrial auto-mation but also in automotive application such as air braking system for trucks and trailers.With the most modern machinery and technology in extrusion system and dimensional control, our company is able to offer the best tolerances for quick fittings.The tube is extruded and coiled on one machine, and then strapped automati-cally, ready for dispatch to the final user.Our company could also mark the tubes with a depth to controlthe correct insertion for push-in fittings.
4 mm
4 mm
4 mm
5 mm
6 mm
6 mm
6 mm
8 mm
8 mm
8 mm
8 mm
9 mm
10 mm
10 mm
10 mm
11 mm
12 mm
12 mm
12,5 mm
14 mm
15 mm
15 mm
16 mm
18 mm
20 mm
0,75 mm
0,85 mm
1 mm
1 mm
1 mm
1,5 mm
2 mm
1 mm
1,25 mm
1,5 mm
2 mm
1,5 mm
1 mm
1,25 mm
2 mm
1,5 mm
1,5 mm
2 mm
1,25 mm
2 mm
1 mm
1,5 mm
2 mm
2 mm
2 mm
+/-0,1 mm
+/-0,1
+/-0,1
+/-0,1
+/-0,1
+/-0,1
+/-0,1
+/-0,1
+/-0,1
+/-0,1
+/-0,15
+/-0,15
+/-0,1
+/-0,12
+/-0,15
+/-0,15
+/-0,15
+/-0,15
+/-0,15
+/-0,15
+/-0,15
+/-0,15
+/-0,15
+/-0,15
+/-0,15
31 bar
36 bar
44 bar
33 bar
27 bar
44 bar
67 bar
19 bar
25 bar
31 bar
44 bar
27 bar
15 bar
19 bar
33 bar
21 bar
19 bar
27 bar
15 bar
22 bar
10 bar
15 bar
19 bar
17 bar
15 bar
34 bar
40 bar
49 bar
37 bar
29 bar
49 bar
73 bar
21 bar
27 bar
34 bar
49 bar
29 bar
16 bar
21 bar
37 bar
23 bar
21 bar
29 bar
16 bar
24 bar
10 bar
16 bar
21 bar
18 bar
16 bar
42 bar
49 bar
60 bar
45 bar
36 bar
60 bar
90 bar
26 bar
33 bar
42 bar
60 bar
36 bar
20 bar
26 bar
45 bar
28 bar
26 bar
36 bar
20 bar
30 bar
13 bar
20 bar
26 bar
23 bar
20 bar
62 bar
72 bar
89 bar
67 bar
53 bar
89 bar
133 bar
38 bar
49 bar
62 bar
89 bar
53 bar
30 bar
38 bar
67 bar
42 bar
38 bar
53 bar
30 bar
44 bar
19 bar
30 bar
38 bar
33 bar
30 bar
31 bar
36 bar
44 bar
33 bar
27 bar
44 bar
67 bar
19 bar
25 bar
31 bar
44 bar
27 bar
15 bar
19 bar
33 bar
21 bar
19 bar
27 bar
15 bar
22 bar
10 bar
15 bar
19 bar
17 bar
15 bar
42 bar
49 bar
60 bar
45 bar
36 bar
60 bar
90 bar
26 bar
33 bar
42 bar
66 bar
36 bar
20 bar
26 bar
45 bar
28 bar
26 bar
36 bar
20 bar
30 bar
13 bar
20 bar
26 bar
23 bar
20 bar
62 bar
72 bar
89 bar
67 bar
53 bar
89 bar
133 bar
38 bar
49 bar
62 bar
89 bar
53 bar
30 bar
38 bar
67 bar
42 bar
38 bar
53 bar
30 bar
44 bar
19 bar
30 bar
38 bar
33 bar
30 bar
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
0 Esterno0 External
SpessoreThickness
Tolleranza DIN0 Esterno
Tollerance DIN0 External
Pressioned’esercizioautorizzata
Allowable workingpressure
Pressioned’esercizioautorizzata
Allowable workingpressure
Pressioned’esercizioautorizzata
Allowable workingpressure
Pressioned’esercizioautorizzata
Allowable workingpressure
Pressioned’esercizioautorizzata
Allowable workingpressure
Pressioned’esercizioautorizzata
Allowable workingpressure
Pressioned’esercizioautorizzata
Allowable workingpressure
DIN 73378tutti i colori
all colours
DIN 74324solo neroonly black
MaterialeRaw material PA12 PHL PA12 PHLY PA12 HL PA11 PHL PA11 PHLY PA11 HL
PA12 HIPHL (Tipo 1 - Type 1)
54
PA
12
& P
A1
1&
TOLLERANZATOLERANCE
Le nostre tolleranze sul diametro esterno sono:Dal 3 mm al 10 mm : +/- 0,10 mmDal 11 mm al 22 mm : +/- 0,15 mm
Su richiesta possiamo offrirvi tubi ad alta precisione con le seguenti tolleranze:Dal 3 mm al 10 mm : +/- 0,03 mmDal 11 mm al 22 mm : +/- 0,05 mm
Tolerance on external diameter as per DIN Norm:From 3 mm to 10 mm : +/- 0,10 mmFrom 11 mm to 22 mm : +/- 0,15 mm
Upon request we could deliver high precision tubes at this tolerance:From 3 mm to 10 mm : +/- 0,03 mmFrom 11 mm to 22 mm : +/- 0,05 mm
TEMPERATURA D’USOTEMPERATURE RANGE
Da -60° C a +130° C
From -60° C to +130° C
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.
Check the table at page 65.
GAMMA COLORICOLOUR RANGE
Per il PA12:For PA12: Naturale
NaturalNeroBlack
AzzurroBlue Sky
BluDark Blue
RossoRed
GialloYellow
VerdeGreen
ArancioOrange
NT NR AZ BL RO GI VE AR
La Castello Italia con un minimo d’ordine di 3.000 m è in grado di offrirvi tubi di colori personalizzati secondo tabella RAL.Castello Italia upon request can offer custom colours following RAL specification for a minimum delivery of 3.000 m.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
MARCATURA MARkING
La nostra marcatura standard è:Our standard marking is:
- DIN 74324 - 6 x 1 mm - PA 12 PHL - C.BEST - 7150 - 11 - 125 - 11:34NormativaNormative
MaterialeRaw material
ø Esterno x Spessoreø External x Thickness
Nome prodottoProduct name
Numero di lottoBatch number
VARIAZIONE DELLE PRESSIONI IN FUNZIONE DELLA TEMPERATURAPRESSURE VARIATION AS FUNCTION OF TEMPERATURE
LUNGHEZZA MATASSAROLL SIZE
Standard 100 mt.Altri avvolgimenti su richiesta.
Standard 100 mt.Other lenghts upon request.
% delle press.
Temp.
100% 87%74% 64% 57%
0%20%40%60%80%100%120%
20°C 30°C 40°C 50°C 60°C
55
PA
12
& P
A1
1&
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
Autom
otiveAutom
otive
- AIRBRAKE AIRBRAKE
TEMPERATURA D’USOTEMPERATURE RANGE
Da -40°C a +93°CFrom -40°C to +93°C
LUNGHEZZA MATASSAROLL SIZE
Standard 100 mt.Altri avvolgimenti su richiesta.
Standard 100 mt.Other lenghts upon request.
RESISTENZE CHIMICHECHEMICAL RESISTANCE
Controllare la tabella a pagina 65.Check the table at page 65.
CONFEZIONAMENTO PACkAGING
Il nostro standard è con film di polietilene. Per le altre tipologie di packaging consultare la pagina 61.
Our standard is with polyethylene film around. For other kinds of packaging check page 61.
I tubi C.Brake sono tubi multistrato rinforzati con treccia in poliestere tra i due strati di PA11. Questi tubi sono co-struiti secondo la normativa SAE J844 tipo B ed anche SAE J1394. I principali campi di utilizzo sono:
1. Impianti frenanti di camion e rimorchi
2. Impianti di controllo dei timoni di barche (basse pressioni)
C.Brake are multilayer tubes reinforced with a polyester braiding between the two PA11 layers.This tube is produced according the SAE J844 type B andSAE J 1394 and it has two main applications:
1. Braking system for trucks and trailers
2. Driving and control system for boats (low pressure)
10 mm
12 mm
16 mm
20 mm
0 Esterno0 External
0 Interno0 Inside
Raggio di curvaturaBending Radius
Pressione esercizio (a 23°)Working pressure (at 23°C)
Pressione scoppio (a 3°C)Burst pressure (at 23°C)
7 mm
8,8 mm
11,32 mm
15,9 mm
1,5 mm
1,6 mm
2,34 mm
2,05 mm
60 mm
72 mm
65 mm
90 mm
29 bar
27 bar
19 bar
17 bar
98 bar
90 bar
63 bar
56 bar
SpessoreThickness
AIR
BR
AK
E
MARCATURA MARkING
La nostra marcatura standard è:Our standard marking is:
- C.BRAKE - SAE J 844 - 10 x 7 mm - PA 11 - AIRBRAKE B - 6109 - 08 - 157 - 21:08NormativaNormative
MaterialeRaw material
ø Esterno x Spessoreø External x Thickness
Nome prodottoProduct name
Numero di lottoBatch number
GAMMA COLORICOLOUR RANGE
Per Airbrake:For Airbrake: Nero
Black
NR
56
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
Per la produzione delle C.Coils la Castello Italia utilizza i tubi C.Best e C.Bio. Nelle pagine dedicate a questi due prodotti po-tete trovare tutte le informazioni tecniche. Le spirali e i sottoti-moni C.Coil sono dedicati esclusivamente al mercato automo-tive sia per il primo equipaggiamento di motrici e rimorchi cheper l’after market.Le componenti e la qualità dei tubi utilizzati per la realizzazionedi questi articoli è conforme alla normativa DIN74323.
Castello Italia uses C.Best and C.Bio tubes to produce C.Coil. You can find in pages dedicated to these tubes all the technical information. Coils and “sottotimoni” C.Coil are especially intended for the market of vehicles, for both the first equipment of trucks, trailers and the after-market. The parts composing these items are of very high quality and comply with the norm DIN74323.
- ImPIAntI FREnAntIAIRBRAKING SYSTEMS
F18 x 1,5
F18 x 1,5
F1/2”
M 16 x 1,5 L 15 mm
M 18 x 1,5 L 34 mm
M 22 x 1,5 L 15 mm
21
95 mm
4,0 m
100 mm
12 x 9 x 1,5 mm
17
120 mm
4,0 m
100 mm
12 x 9 x 1,5 mm
Standard / Standard
Spire / Turns
D
L
C
Tubo / Tube
Stretta / Narrow
L
C
D
SPIRALI PER SEMIRIMORCHISEMI-TRAILERS COILS
IMPIAN
TI FRENAN
TI
GAMMA COLORICOLOUR RANGE
Per queste spirali:For these coils: Nero
Black
NRBluDark Blue
BLRossoRed
ROGialloYellow
GI
F18 x 1,5
F1/2”
F1/2”
M 16 x 1,5 - L 15 mm
M 22 x 1,5 - L 15 mm
M 26 x 1,5 - L 15 mm
7
100 mm
4725 mm
100 mm
12 x 9 x 1,5 mm
0
100 mm
2740 mm
0 mm
12 x 9 x 1,5 mm
Standard / Standard
Spire / Turns
D
L
C
Tubo / Tube
Stretta / Narrow
L
C
D
SOTTOTIMONI PER RIMORCHITRAILERS “SOTTOTIMONI”
57
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
58
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
IMP
IAN
TI F
REN
AN
TI
GAMMA COLORICOLOUR RANGE
Per queste spirali:For these coils: Nero
Black
NRBluDark Blue
BLRossoRed
ROGialloYellow
GI
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
M16 x 1,5
A
M18 x 1,5
M22 x 1,5
21
95 mm
4,0 m
100 mm
12 x 9 x 1,5 mm
17
120 mm
4,0 m
100 mm
12 x 9 x 1,5 mm
Standard / Standard
Spire / Turns
D
L
C
Tubo / Tube
Stretta / Narrow
L
CA
D
DATI TECNICITECHNICAL DATA
Raccordo / Fitting
- ImPIAntI FREnAntIAIRBRAKING SYSTEMS
58
Le spirali C.Coil dedicate agli impianti frenanti possono es-sere fornite anche nella versione con doppi raccordi femmi-na M18 cosi da poter accettare qualsiasi tipologia di nipplo.Per evitare la piegatura dei codoli e il loro relativo danneg-giamento vengono posizionate due protezioni in plastica co-lorata nere, rosse o gialle insieme ad un apposito occhiello per l’aggancio alla cabina. Queste spirali sono fornibili sia nella versione a 21 spire che in quella a 17 spire.
C.Coil spirals for air braking systems can be produced with two M18 (thread female) “swivel nut” push-in fittings. This solution could permit to use every kind of adapters with a maximum of flexibility for drivers. To protect the tube we insert two anti-kink protection in plastic black, red or yellow with stowage loop to connect it at the truck cabin. This air-coil is available in 21 turns and 17 turns version.
- SPIRALI In SUPER PURCOIL IN SUPER PUR
I valori ed i coefficienti indicati nelle tabelle riportate su questo catalogo sono puramente indicativi, non sono vincolanti per Castello Italia srl e non comportano elemento di responsabilità a carico della stessa in caso di difformità rispetto a dette tabelle, ovvero in caso di erroneo impiego del prodotto da parte del Cliente.
The values and coefficients contained in this document are for information only and shall in no event be held to constitute or imply any warranty, undertaking, express or implied commitment. No liability whatsoever can be accepted by Castello Italia Srl with respect to difference to the values reported in the tables or misuse by the Customer of the products.
59
F18 x 1,5 M 16 x 1,5 L 15 mm
24
74 mm
4,5 m
100 mm
12 x 8 x 2 mm
Standard / Standard
Spire / Turns
D
L
C
Tubo / Tube
L
C
D
DATI TECNICITECHNICAL DATA
GAMMA COLORICOLOUR RANGE
Per Airbrake:For Airbrake: Nero
Black
NRBluDark Blue
BLRossoRed
ROGialloYellow
GI
Queste spirali posso essere prodotte in coppia con una spirale a 21 spire all’interno ed a 24 spire all’esterno.Those kind of coils are also produced in dual-in combination with one internal coils with 21 turns and one external with 24 turns. Codice Prodotto - Product code:CA.UD.8.D00.33.RG
Codice prodotto - Product code:CA.UD.8.R24.33.GI (RO, NR, BL)
Le spirali vengono raccordate con due raccordi M16x1,5 con ORThose coils are supplied with fitting M16x1,5 with OR
SUPER PUR
Queste spirali vengono realizzate con una speciale mescola di poliuretano e trovano la loro applicazione nel passaggio di aria compressa, offrendo un’ottima memoria elastica e meccanica.Vengono realizzate sia a 21 spire con lunghezza di lavoro di 4,5 metri e sia in coppia, confezionate l’una dentro l’altra, per ridurre l’ingombro.
Those anti-knicking coils are made of special polyuretha-ne resin and due to their outstanding properties as such spring, they can be used for specific air compressed appli-cations.Available on 21 turns with 4,5 meters, working length, and in dual-in combination.
& PACKAGING
- SCATOLEBOXES
Al fine di proteggere i propri tubi e facilitare gli utilizzatori che ne-cessitano di piccole pezzature di tubo è stata creata la C.Box. Le nostre scatole disponibili nelle dimensioni 255X255X70 mm, 300X300X80 mm, 400x400x110 mm, 600x600x110 mm possono contenere, a seconda della tipologia di materiale e dia-metro del tubo, matasse da 25mt, 50 mt e 100mt.
C.BOX has been created to contain and protect small quan-tity of tubes for an easy use. Our boxes, available in two sizes 255X255X70 mm, 300X300X80 mm, 400x400x110 mm, 600x600x110 mm could contain rolls of 25mt, 50mt and 100mt, depending on type of material and diameter.
MATASSE STANdArd CON FILM dI POLIETILENESTANDARD ROLLS WITH POLYTETHILE FILM AROUND
Disponibili in 25 mt, 50 mt, 100 mt, 200 mt.Available in 25 mt, 50 mt, 100 mt, 200 mt.
MATASSE IN SACCHETTO IN POLIETILENEROLLS IN POLYETHYLENE BAG
250 mm
500 mm
310 mm
310 mm
Di
600 mm
1000 mm
700 mm
600 mm
De
300 mm
470 mm
480 mm
315 mm
L
42 mm
82 mm
82 mm
82 mm
Foro centraleCentral hole
TIPO A / TYPE A
TIPO H / TYPE H
TIPO L / TYPE L
TIPO D / TYPE D
DIMENSIONI BOBINA / DRUM DIMENSION
QUANTITà DI TUBO AVVOLGIBILE SULLE DIVERSE TIPOLOGIE DI BOBINEQUANTITY OF TUBE ON EACH TYPE OF DRUM
3000 m
1500 m
850 m
500 m
TIPO ATYPE A
350 m
14000 m
6500 m
3500 m
2000 m
TIPO HTYPE H
1500 m
7000 m
3000 m
1500 m
1000 m
TIPO LTYPE L
800 m
2500 m
1000 m
650 m
400 m
TIPO DTYPE D
280 m
4 mm
6 mm
8 mm
10 mm
12 mm
0 Esterno0 External
BOBINE IN LEGNO O IN PLASTICAWOOD OR PLASTIC DRUMS
De Di
L
PackagingPackaging
61
63
CODIFICA TUBI E SPIRALITUBES AND COILS CODE
TUBITUBES
SPIRALICOILS
Esempio / Example: 2F.008.006.0100.0.NR
PRIMA PARTE: MATERIALE / FIRST PART: MATERIAL
1F = PA11 FLESSIBILE / FLEXIBLE PA112F = PA12 FLESSIBILE / FLEXIBLE PA121R = PA11 RIGIDO / RIGID PA112R = PA12 RIGIDO / RIGID PA12 UC = POLIURETANO sh.A98 C.FLEX E C.KOLOR / POLIURETHANE sh.A98 C.FLEX AND C.KOLORUA = POLIURETANO sh.A95 / POLIURETHANE sh.A95PE = POLIETILENE BASSA DENSITÀ / LOW DENSITY POLIETHILENE TE = TEFLON2A = ATEXMU = MULTITUBO / MULTITUBE
AI = AIRBRAKE QA = COPU 55 ShDHT = C.HOT
SP = C.SPARK
SECONDA PARTE: DIAMETRO ESTERNO /SECOND PART: EXTERNAL DIAMETER
Esempio / Example:
006 = 6 mm 008 = 8 mm 010 = 10 mm
TERZA PARTE: DIAMETRO INTERNO /THIRD PART: INTERNAL DIAMETER
Esempio / Example:
004 = 4 mm006 = 6 mm008 = 8 mm
QUARTA PARTE: METRI PER ROTOLO /FOURTH PART: METER EACH ROLL
Esempio / Example:
0100 = 100 m per rotolo (produzione standard) /100 m each roll (standard production)
1000 = 1000 m per rotolo / 1000 m each roll
QUINTA PARTE: IMBALLO / FIFTH PART: PACKAGING
Esempio / Example:
0 = standard packaging (rotolo nel film) / standard packaging (filmed roll)
W = c.box piccola / little c.boxY = c.box grande / big c.box
SESTA PARTE: COLORE / SIXTH PART: COLOUR
NR = nero /black
NT = naturale /natural
AZ = azzurro /sky blue
BL = blu /dark blue
012 = 12 mm014 = 14 mm
010 = 10 mm012 = 12 mm
RO = rosso /redAT = azzurro trasparente /transparent skyblueRT = rosso trasparente /transparent redGT = giallo trasparente /transparent yellowVT = verde trasparente /transparent green
Esempio / Example: S1.2F.10.0030.AR
PRIMA PARTE: TIPO DI SPIRALE /FIRST PART: KIND OF COIL
Esempio / Example:
S1 = senza coduli / without terminalsS2 = con coduli e raccordi / with terminals and fittingsS3 = con coduli, senza raccordi / with terminals, no fittings
SECONDA PARTE: MATERIALE / SECOND PART: MATERIAL
Esempio / Example:
2F = PA12 FLESSIBILE / PA12 FLEXIBLEUA = POLIURETANO / POLIURETHANE
TERZA PARTE: DIAMETRO ESTERNO DEL TUBO /THIRD PART: EXTERNAL DIAMETER OF THE TUBE
Esempio / Example:
4 = 4 mm6 = 6 mm8 = 8 mm
QUARTA PARTE: LUNGHEZZA DEL TUBO IMPIEGATO /FOURTH PART: LENGTH OF THE TUBE USED
Esempio / Example:
0010 = 10 m0015 = 15 m
0030 = 30 m
QUINTA PARTE: COLORE / FIFTH PART: COLOUR
Esempio / Example:
AR = arancione /orangeBL = blu /dark blueAZ = azzurro /sky blue
10 = 10 mm12 = 12 mm15 = 15 mm
CodiciH
ow to order
ul. Hangarowa 8, 70-767 Szczecin tel. : +48 +91 4640 641 fax : +48 +91 4627 359
www.phu-nova.eue-mail: [email protected]
65O: OTTIMA RESISTENZA / GOOD RESISTANCE G: AZIONE GONFIANTE / SWELLING ACTION L: RESISTENZA LIMITATA / LIMITED RESISTANCE N: PESSIMA RESISTENZA / POOR RESISTANCE
SOSTANZASUBSTANCE
AcetaldeideAcetaldehyde
Acetato d’amileAmyl acetate
Acetato d’etileEthyl acetate
AcetileneAcetylene
AcetoVinegar
AcetoneAcetone
Acido AceticoAcetic acid
Acido CitricoCitric Acid
Acido Cloridrico 1% Hydrocloric Acid 1%
Acido Cloridrico 10% Hydrocloric Acid 10%
Acido formico concentr. Formic Acid
Acido LatticoLactic Acid
Acido NitricoNitric Acid
Acido OleicoOleic Acid
Acido OssalicoOxalic Acid
Acido SalicidicoSalicylic Acid
Acido Solforico 10% Sulphuric Acid 10%
Acido Solforico concentr. Concentrated Sulphuric Acid
Acido StearicoStearic Acid
Acido TartaricoTartaric Acid
Acido UreicoUreic Acid
AcquaWater
Acqua marinaSea Water
Acqua Ossigenata 20% Hydrogen Peroxide 20%
Alcool BenzilicoBenzyl Acohol
AmidoStarch
Ammoniaca (soluz. acqu.) Ammonia Liquid
Anidride SolforosaSulohur Chloride
AnilinaAniline
AntigeloAntigelo
BenzinaPetrol
BenzoloBenzol
BromoBromine
ButanoButane
ButanoloButanol
Carbonato potassico Potassium Carbonate
-
-
-
-
-
-
L
L
N
N
N
N
N
-
-
-
L
N
-
-
-
O
O
-
N
-
-
-
-
-
-
-
-
-
-
-
O
O
O
O
O
O
O
O
L
L
L
O
N
O
O
O
L
N
O
O
O
O
O
L
N
O
O
L
G
O
G
G
N
O
O
O
O
O
O
O
O
O
O
O
L
L
L
O
N
O
O
O
L
N
O
O
O
O
O
L
N
O
O
L
G
O
O
O
N
O
O
O
O
O
O
O
O
O
O
O
N
N
N
O
N
O
O
O
N
N
O
O
O
O
O
-
N
O
O
-
-
-
-
-
N
O
-
O
O
-
O
-
O
O
O
-
O
O
O
O
N
O
O
-
G
G
G
O
N
O
O
G
G
O
G
N
-
-
G
N
N
O
-
-
N
O
O
O
O
N
O
O
O
O
O
O
L
O
O
O
O
O
O
O
O
O
O
O
O
O
N
O
O
-
O
O
O
O
-
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
-
O
O
-
-
-
-
O
-
O
POLIAMMIdE 12POLyAmidE 12
POLIAMMIdE 11POLyAmidE 11
POLIAMMIdE 6POLyAmidE 6
POLIURETANOPOLiUrETHANE
POLIETILENEPOLiETHiLENE
PVdF(KyNAR®, ...)
PTFE(TEFLON®, ...)
RESISTENZE CHIMICHE A +23°CCHEMICAL RESISTANCE AT +23°C
Res. chimiche
Pres. scoppioChem
ical resistanceBurst pressure
O: OTTIMA RESISTENZA / GOOD RESISTANCE G: AZIONE GONFIANTE / SWELLING ACTION L: RESISTENZA LIMITATA / LIMITED RESISTANCE N: PESSIMA RESISTENZA / POOR RESISTANCE
SOSTANZASUBSTANCE
Carbonato sodico 10% Sodium Carbonate 10%
Carbonato sodico 50% Sodium Carbonate 50%
Carburante disel Gasoil
CeraWax
CheroseneKerosene
CloroChlorine
ClorobenzoloChlorobenzol
CloroformioChloroform
Cloruro di magesio 10%magnesium Chloride 10%
Cloruro di metilene methylene Chloride
Cloruro di sodio saturo Sodium Chloride
Cloruro di zinco soluz. acq. Zinc Chloride (water based)
CresoloCresol
decalinadecaline
EptanoHeptane
EtanoloEthanol
EtereEther
Etere di petrolioOil Ether
FenoloPhenol
FormaldeideFormaldeyde
Freon F 12 LiquidoFrigen F 12 Liquid
Gas FluoridiricoHydrofluoridric gas
GlicerinaGlycerin
GlicoleGlycole
GrassiGreese
Grasso alimentareGreese food
Idrogeno solforatoHydrogen XXXX
Isottanoisoocthane
Isopropanoloisopropanol
Lattemilk
Liscivia saponosaSoap Suds
Mercuriomercury
Metanolomethanol
NaftaNaptha
NaftalinaNapthalene
Nitrobenzolo Nitrobenzol
O
L
O
O
O
N
N
N
O
O
O
O
L
O
O
O
O
-
N
L
G
-
OG
O
O
O
-
OG
-
O
O
O
L
O
O
L
O
O
O
O
O
N
N
N
O
O
O
O
L
O
O
O
O
O
N
L
O
L
O
O
O
O
O
O
O
O
O
O
L
O
O
L
-
-
N
-
-
-
-
N
-
N
-
-
-
-
-
-
-
-
-
-
-
-
O
L
-
-
-
-
N
O
-
-
N
-
-
-
-
-
N
-
O
N
-
N
O
O
O
O
N
O
O
-
-
-
-
-
-
-
O
O
O
O
-
-
-
O
O
-
-
O
-
-
-
-
-
-
-
-
N
O
N
O
O
N
N
G
O
N
-
N
O
-
-
O
O
O
O
O
N
-
O
G
O
O
-
O
-
O
O
-
-
O
O
O
O
O
O
O
O
O
O
-
-
-
-
O
O
O
-
O
O
O
O
-
O
-
O
O
O
-
-
O
-
-
-
-
-
-
O
O
O
O
O
O
O
O
O
-
-
-
-
O
O
O
-
O
O
O
O
-
-
-
O
O
O
-
O
O
-
POLIAMMIdE 12POLyAmidE 12
POLIAMMIdE 11POLyAmidE 11
POLIAMMIdE 6POLyAmidE 6
POLIURETANOPOLiUrETHANE
POLIETILENEPOLiETHiLENE
PVdF(KyNAR®, ...)
PTFE(TEFLON®, ...)
RESISTENZE CHIMICHE A +23°CCHEMICAL RESISTANCE AT +23°C
66
O: OTTIMA RESISTENZA / GOOD RESISTANCE G: AZIONE GONFIANTE / SWELLING ACTION L: RESISTENZA LIMITATA / LIMITED RESISTANCE N: PESSIMA RESISTENZA / POOR RESISTANCE
SOSTANZASUBSTANCE
OleumOleum
OliOils
Olio di paraffinaParafin Oil
Olio di siliconeSilicon Oil
Olio idraulicoHydraulic Oil
Olio mineralemineral Oil
Olio per motoriEngine Oil
Olio per trasformatori Transformer Oil
Ossido d’etileEthyl Oxide
OssigenoOxigen
OzonoOzone
Percloroetilene Perchloroethylene
Permanganato potas.Potassium Permanganate
PetrolioPetroleum
PiridinaPyridine
Potassa caustica 10% Potassium Hydroxide 10%
Potassa caustica 50%Potassium Hidroxide 50%
PropanoPropane
Sale da cucinaSodium Chloride
SegoTallow
Soda caustica 10%Soda 10%
Soda caustica 50% Soda 50%
Solfato di rameSodium Sulphate
Solfato di sodioSodium Sulphate
StearinaStearine
StireneStyrene
Tetracloruro di carb.Carbon tetrachloride
TetralinaTetralin
Tintura di iodioiodine tincture
ToluoloToluole
TrementinaTurpentine
TricloroetanoTrichlorethane
UreaUrea
UrinaUrine
VasellinaVaselline
XioloXyolo
L
O
O
O
O
O
O
O
O
O
L
N
N
O
N
OG
OG
O
O
O
O
O
O
O
O
O
L
-
-
O
O
L
O
O
O
O
L
O
O
O
O
O
O
O
O
O
L
O
N
O
O
O
O
O
O
O
O
O
O
O
O
O
L
O
L
O
O
L
O
O
O
O
N
-
O
O
O
O
O
O
-
O
N
O
N
O
N
-
-
O
-
-
-
-
O
-
O
-
O
-
-
O
O
N
O
O
O
-
N
-
O
O
O
O
O
O
N
-
N
-
O
OG
OG
O
O
-
O
O
-
-
O
-
-
-
N
-
-
N
OG
N
O
O
O
-
N
O
O
O
O
O
O
O
-
O
O
O
O
O
N
N
N
O
O
O
-
-
O
-
-
-
O
-
-
O
O
O
O
O
O
-
-
O
O
O
O
O
O
O
-
O
O
O
-
O
-
-
-
O
-
-
-
-
-
-
-
O
O
-
-
-
O
-
O
O
O
-
-
-
-
-
-
-
-
-
-
N
-
-
N
-
N
-
-
-
-
-
-
-
-
-
-
-
N
-
-
-
-
N
-
-
-
-
POLIAMMIdE 12POLyAmidE 12
POLIAMMIdE 11POLyAmidE 11
POLIAMMIdE 6POLyAmidE 6
POLIURETANOPOLiUrETHANE
POLIETILENEPOLiETHiLENE
PVdF(KyNAR®, ...)
PTFE(TEFLON®, ...)
RESISTENZE CHIMICHE A +23°CCHEMICAL RESISTANCE AT +23°C
67
Pressione di Scoppio e pressione d’esercizioBurst pressure and working pressure Calculation
1. Calcolo pressione di scoppio a 23°C:Burst Pressure calculation (at 23°C)
Queste informazioni sono intese come aiuto per il reparto tecnico nel disegno di tubi.Tutto parte da questa formula:
The following information is intended to help technical departments in designing a tube fitting their particular requirements.It all begins with the following formula:
Pb: Pressione di scoppio in N/mm2Burst Pressure in N/mm2
Bs: Basic stress in N/ mm2 (vedere tabella qui sotto)Basic stress in N/ mm2 (see table below for value/material)
Dm: Diametro medio del tubo in mm = De – SMean tube Diameter in mm = De – S
De: Diametro esterno del tubo in mmExternal tube Diameter in mm
S: Spessore del tubo in mmThickness of the tube in mm
Pb= Bs 20sxDm
PA12 HL PA12 PHLY PA12 PHL PA11 HL PA11 PHL PA6 HL PA6 HIHLMaterialiMaterial
Bs in N/mm2 40 27 20 40 20 30 25
PVDF KYNARCOPU 55ShD PELD PEHD PU Sh. 95 APU Sh. 98 A PTFE TEFLONMaterialiMaterial
Bs in N/mm2 2514 8 10 10 8 14
2. Calcolo pressione d’ esercizio a 23°C:Working Pressure calculation (at 23°C)
Le norme DIN 73378 e DIN 74324 (come scritto su nostri tubi in poliammide) sono il riferimento per quanto riguarda la pressione d’esercizio come mostra la seguente formula:
The DIN 73378 and DIN 74324 (as written on our tubes in polyamide) is the reference in regard to working pressure with following formula:
Pw: Pressione d’esercizio in bar Working Pressure in bar
Pb: Pressione di scoppio in bar Burst pressure in bar
Pw= Pb / 3
68
ul. Hangarowa 8, 70-767 S zczecin tel.: +48 +91 4640 641 fax :+48 +91 4627 359
www.phu-nova.e ue-mail: [email protected]