turning tools for small lathes j-serieskozaktools.com.ua/wp-content/uploads/2018/10/jser.pdf ·...
TRANSCRIPT
-
No.345-E
Turning Tools for Small Lathes
J-SERIES
Expanded Items for All Types of Machining
-
1
●New free-cutting chipbreakers for burrless machining.●Sharp cutting edges just fit for low-feed machining inherent to small-lathe turning.●Honed-edges completely prevent the insert from chipping. ●Four surfaces of the shank are ground for maintaining highly accurate machining.●The type numbers starting from “J” allow easy selection of the insert and the toolholder.●The highly rigid tool design has realized precision machining at deep cuts.●In the back-clamping type tools, the insert can be changed and indexed from back side of the toolholder.
●Applicable to radial tool post (“-C” type)
Min. simultaneous machiningdiameter:φ8
45゜
FEATURES OF J-SERIES TURNING TOOLS FOR SMALL LATHES
●The toolholders whose final letter of the Cat.No.is“-C”are applicable to radial tool post tooling.●Work diameters down to φ8 can be simultaneous-
ly machined. ●“-C”type toolholders are available for front turn-
ing,reverse turning,threading,cutting-off,and grooving.
●Applicable to a variety of operations such as front turning, back turning, grooving, threading, cutting-off, and boring.
Back turningDepth of cut: < 5.5 mm
BoringMin. bore dia.: φ5.5
External turning
Round-shankExternal profiling(Available for backturning, threading,and grooving)
ThreadingPitch: 0.5 - 1.0 mm
GroovingEdge width: 0.33 - 3.0 mmGroove depth: < 2.6 mm
Cutting-offEdge width: 0.7 - 2.0 mmWork dia.: < φ32
Reverse turningDepth of cut:< 5.5 mm
Front turningDepth of cut: < 5.5 mm
“-C”type
JSXG type
40°
P28~30
P27
P17P17P21~23
P11~16
P21,24~25 P18~20
P26
No interference
-
2
INSERT GRADES FOR J-SERIES
●Standard Cutting ConditionsWork materials
General steelsFree-cutting steels
Stainless steels
Cast irons
Nonferrous metals
Difficult-to-cut materials
Hard materials
Applications Chipbreakers Grades
J530
J740
NS530
J530
J740
J530
J740
NS530
J530
J740
TH10
TH10
TH10
TH10
Precision finishing
Finishing
Precision finishing
Finishing
Finishing
Finishing
Finishing
Finishing
0.05-0.5
0.1-5.0
0.05-0.5
0.1-5.0
0.1-5.0
0.1-5.0
0.1-5.0
0.1-5.0
0.03-0.15
0.01-0.3
0.03-0.15
0.01-0.1
0.01-0.1
0.01-0.1
0.01-0.1
0.01-0.1
100-300
10-100
80-300
80-300
10-100
100-200
10-100
100-200
100-200
10-100
20-100
100-1000
10-150
10-60
01
J□□
01
J□□
J□□
J□□
J□□
J□□
●Features of J740
●Features of Grades
●A optimum combination of the micro-grain cemented carbide substrate and special thin-film coating “J-Coat” has realized the cutting-edge sharpness and long tool life.
Comparison of cutting-edge sharpness
Material typeGrades Features
J740
NS530
J530
TH10
Micro-grain cemented carbide+
PVD coating
Cermet
Cermet + PVD coating
Cemented carbide
• All-rounder for general steels to stainless steels and free-cutting steels.• The cutting edge sharpness and “J-Coat” realizing long tool life contribute to
the outstanding cutting performance in the surface finish and wear resistance.
• Applicable to high-speed cutting of general steel to stainless steels. • Excellent surface finish inherent to cermet.
• The cutting edge sharpness and “J-Coat” realizing long tool life contribute to the outstanding cutting performance in the wear resistance.
Long tool life in machining of aluminum alloys, brass, and difficult-to-cut materials.
Depth of cut ap (mm) Feed f (mm/rev) Cutting Speed V (m/min)
Conventional cemented carbideJ740
ChippingGood
J-series Competitor’s grade
-
3
●Wrenching from the back side of the toolholder allows easy indexing and changing of the insert.
Clamping screw
BACK-CLAMPING TOOLHOLDERS (Negative types have been added to the existing positive types.)
ClampInsert
Narrow space
Wrench
For external turning JTTAN type (Negative, back clamping)
For external turning and facing JTCL2N type (Negative, back clamping)
For external profiling JTDJ2N type (Negative, back clamping)
f b
hh 1f b
h
f b
h
TN□□1604□□
Shank size (mm)Applicable insert
DN□□1104□□
Shank size (mm)Applicable insert
CN□□0903□□
Shank size (mm)Applicable insert
Note : For positive back-clampingtoolholders, see page 11.
●The back-clamping mechanism for easy changing and indexing of the insert on an automatic lathe.●No parts apart from the shank when indexing or changing the in-
sert.●Ensures precise positioning of the insert. ●Newly added negative rake toolholders allow use of a variety of
three-dimensional chipbreaker inserts, resulting in improved chip control and machining efficiency.●Use of negative inserts which excel in the number of available cut-
ting edges allows reducing of machining costs.
●Because of the narrow spacing between the adjacent tools on a gang tool post, it is not easy to change or index the insert on a conventional screw-on type toolholder. Whereas, the back-clamping toolholder allows easy indexing or changing of the insert by wrenching from back side of the shank.
�2�1
h1
�2
�1
h1
�2�1
h
1216
1616
b h
1216
1616
b
h
1216
1616
b
-
4
ROUND-SHANK TOOLHOLDERS
For external profiling
For back turning
For grooving
For threading
●Can resolve a shortage of the number of tools installed on a machine in machining of complex parts.
Available shank size: φ19.05, φ20.0, φ22.0, and φ25.4.
●Applicable to the machines of the maximum machining diameters from φ12 to φ32 .
DC□□0702□□
DC□□11T3□□
Shank diameterApplicable inserts
φ19.05~φ22.0
φ19.05~φ25.4
JTGR3□□□
Shank diameterApplicable inserts
φ19.05~
φ25.4
Groove width
0.33~
3.0mm
Groove depth
0.7~
2.6mm
JTTR30□□
Shank diameterApplicable inserts
φ19.05~
φ25.4
θ
60 ゚
55 ゚
Pitch range
0.5~
1.0mm
JTBR30□□
Shank diameterApplicable inserts
φ19.05~
φ25.4
Max. depth of cut
2.5mm
JS-SDUCL type JS-TGL3 type
JS-TBL3 type JS-TTL3 type
●By installing round-shank tools in sleeve holders on the front and back side tool posts, enabling front and back turning, groov-ing, and threading, the number of tools installed in external ma-chining process can be increased.
-
●●
●●
●
●●
●●
●
在 庫在 庫在 庫
CCGT060202-01CCGT09T302-01
DCGT070202-01DCGT11T302-01
TCGT110202-01
6.3509.525
6.3509.525
6.350
2.383.97
2.383.97
2.38
0.20.2
0.20.2
0.2
TAC INSERTS FOR GENERAL TURNING
在 庫
CCGT060200FR/L-J10CCGT060201FR/L-J10CCGT060202FR/L-J10CCGT09T300FR/L-J10CCGT09T301FR/L-J10CCGT09T302FR/L-J10DCGT070200FR/L-J10DCGT070201FR/L-J10DCGT070202FR/L-J10DCGT11T300FR/L-J10DCGT11T301FR/L-J10DCGT11T302FR/L-J10TCGT080200FR/L-J08TCGT080201FR/L-J08TCGT080202FR/L-J08TCGT110200FR/L-J10TCGT110201FR/L-J10TCGT110202FR/L-J10TCGT110300FR/L-J10TCGT110301FR/L-J10TCGT110302FR/L-J10VBGT110300FR/L-J10VBGT110301FR/L-J10VBGT110302FR/L-J10VBGT110304FR/L-J10
6.350
9.525
6.350
9.525
4.760
6.350
6.350
6.350
2.38
3.97
2.38
3.97
2.38
2.38
3.18
3.18
0.030.10.20.030.10.20.030.10.20.030.10.20.030.10.20.030.10.20.030.10.20.030.10.20.4
●●●●●●●●●●●●●●●●●●●●●●●●●
●●●●●●●●●●●●●●●●●●●●●●●●●
●●●●●●●●●●●●●●●●●●●●●●●●●
●J-type chipbreaker for finishing(Sharp edge)
●●●●●●●●●●●●●●●●●
6.350
9.525
6.350
9.525
4.760
6.350
6.350
6.350
CCGT060201R/L-J10CCGT060202R/L-J10CCGT09T301R/L-J10CCGT09T302R/L-J10DCGT070201R/L-J10DCGT070202R/L-J10DCGT11T301R/L-J10DCGT11T302R/L-J10TCGT080201R/L-J08TCGT080202R/L-J08TCGT110201R/L-J10TCGT110202R/L-J10TCGT110301R/L-J10TCGT110302R/L-J10VBGT110301R/L-J10VBGT110302R/L-J10VBGT110304R/L-J10
2.38
3.97
2.38
3.97
2.38
2.38
3.18
3.18
0.10.20.10.20.10.20.10.20.10.20.10.20.10.20.10.20.4
●J-type chipbreaker for finishing(Honed)
■Positive Inserts for J-series●01-type chipbreaker for precision finishing
5
2.8
4.4
2.8
4.4
2.2
2.8
2.8
2.8
2.8
4.4
2.8
4.4
2.2
2.8
2.8
2.8
2.84.4
2.84.4
2.8 ●
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
J530 J740 NS530 TH10
Stocked gradesUncoatedCermet
Hole dia.Insert Cat. No.
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
J530 J740 NS530 TH10
Stocked gradesUncoatedCermet
Hole dia.Insert Cat. No.
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
J530 J740 NS530 TH10
Stocked gradesUncoatedCermet
Hole dia.Insert Cat. No.
Stock status ●: Stocked item
-
Stock status ●: Stocked item
●●●●●●●●●●●●
在 庫在 庫在 庫
T9015 NS530CCMT060202-PFCCMT060204-PFCCMT060208-PFCCMT09T302-PFCCMT09T304-PFCCMT09T308-PFDCMT070202-PFDCMT070204-PFDCMT070208-PFDCMT11T302-PFDCMT11T304-PFDCMT11T308-PF
6.350
9.525
6.350
9.525
2.38
3.97
2.38
3.97
0.20.40.80.20.40.80.20.40.80.20.40.8
2.8
4.4
2.8
4.4
●●●●●●●●●●●●
●●●●●●●●●●●●
●●●●●●●●●●●●
●●
●●
●●
●●
●●●●●●●●●●●●
T9025 T6020 T6030 GH730
●PS-type chipbreaker for finishing to medium cutting
●●●●●●●●●●●●●●●
●●●
在 庫在 庫在 庫
T9015 NS530CCMT060202-PSCCMT060204-PSCCMT060208-PSCCMT09T302-PSCCMT09T304-PSCCMT09T308-PSDCMT070202-PSDCMT070204-PSDCMT070208-PSDCMT11T302-PSDCMT11T304-PSDCMT11T308-PSTCMT110202-PSTCMT110204-PSTCMT110208-PS
VBMT110302-PSVBMT110304-PSVBMT110308-PS
6.350
9.525
6.350
9.525
6.350
6.350
2.38
3.97
2.38
3.97
2.38
3.18
0.20.40.80.20.40.80.20.40.80.20.40.80.20.40.8
0.20.40.8
2.8
4.4
2.8
4.4
2.8
2.8
●●●●●●●●●●●●●●●
●●●
●●●●●●●●
●●●●●
●●●
●●●●●●●●
●●●●●
●●●
●●●●●●●●●●●●●●●
●●●●●●●●●●●●●●●
●●●
T9025 T6020 T6030 GH730
●PM-type chipbreaker for medium cutting
●●●●●●●●●●●●●●●
在 庫在 庫在 庫
T9015 NS530CCMT060204-PMCCMT060208-PMCCMT09T304-PMCCMT09T308-PMCCMT09T312-PMDCMT070204-PMDCMT070208-PMDCMT11T304-PMDCMT11T308-PMDCMT11T312-PMTCMT110204-PMTCMT110208-PMTCMT16T304-PMTCMT16T308-PMTCMT16T312-PM
6.350
9.525
6.350
9.525
6.350
9.525
2.38
3.97
2.38
3.97
2.38
3.97
0.40.80.40.81.20.40.80.40.81.20.40.80.40.81.2
2.8
4.4
2.8
4.4
2.8
4.4
●●●●●●●●●●●●●●●
●●●●●●●●●●●●●●●
●●●●
●●●●
●●●●●●●●●●●●●●●
T9025 T6020 T6030 GH730
●●●●●●●●●●●●●●●
●●●
AT530
6
■General Purpose Positive Inserts●PF-type chipbreaker for finishing
●●●●●●●●●●●●●●●
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)CoatedStocked grades
CermetHole dia.
Insert Cat. No.
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
Stocked gradesCermet
Hole dia.Insert Cat. No.
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)CoatedStocked grades
CermetHole dia.
Insert Cat. No.
-
Stock status ●: Stocked item
7
■General Purpose Negative Inserts●01-type chipbreaker for precision finishing
●●●
在 庫在 庫在 庫
T9005CNGG090302-01CNGG090304-01CNGG090308-01DNGG110402-01DNGG110404-01DNGG110408-01TNGG160402-01TNGG160404-01TNGG160408-01TNGG160412-01
9.525
9.525
9.525
T9015 T9025 T9035 T6020 T6030 GH110 NS530 GT530 TH10 TX20●●●●●●●●●●
●●
3.18
4.76
4.76
3.81
3.81
3.81
0.20.40.80.20.40.80.20.40.81.2
在 庫在 庫在 庫
T9005TNGG160400R-CTNGG160400L-CTNGG160402R-CTNGG160402L-CTNGG160404R-CTNGG160404L-CTNGG160408R-CTNGG160408L-C
T9015 T9025 T9035 T6020 T6030 GH110 NS530 GT530 TH10 TX20
0.03
0.2
●C-type chipbreaker for precision finishing
在 庫在 庫在 庫
T9005TNMG160404-TSTNMG160408-TSTNMG160412-TS
9.525
T9015 T9025 T9035 T6020 T6030 GH110 NS530 GT530 TH10 TX20
4.76 3.810.40.81.2
●TS-type chipbreaker for finishing
●●
●●
●●●
●●●
●●●
●●●
●●●
在 庫在 庫在 庫
T9005TNGG160402R-PTNGG160402L-PTNGG160404R-PTNGG160404L-PTNGG160408R-PTNGG160408L-P
9.525
T9015 T9025 T9035 T6020 T6030 GH110 NS530 GT530 TH10 TX20●●●●●●
4.76 3.18
0.2
0.4
0.8
●P-type chipbreaker for medium cutting
●●●●●●
●●●●●●
9.525 4.76 3.810.4
0.8
●●●●●●●●
●●●●●●
●
●●●●
●●●●
●Standard cutting conditions and grades for general purpose chipbreaker insertsChipbreaker Depth of cut ap (mm) Feed f (mm/rev)PFPSPMCTSP
0.3-1.50.3-2.00.5-3.00.5-3.00.3-1.51.0-4.0
0.05-0.250.08-0.30.15-0.30.1-0.30.08-0.20.2-0.5
General steelsFree-cuttingsteels
Applicable work materials Insert grades Cutting speed Vc (m/min)
Stainless steels
Cast irons
T9005T9015T9025T9035GH730NS530T6020T6030GH730NS530GH110
GT530
GT530
100-40080-35080-30050-20050-15080-300100-20050-15050-120100-20030-150
●
●●●●
UncoatedAppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
Stocked gradesCermet
Hole dia.Insert Cat. No.
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
Stocked gradesCermet
Hole dia.Insert Cat. No. Uncoated
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
Stocked gradesCermet
Hole dia.Insert Cat. No. Uncoated
AppearanceI.C. dia. Thickness Corner radius
Dimensions (mm)Coated
Stocked gradesCermet
Hole dia.Insert Cat. No. Uncoated
-
J-SERIES TOOLHOLDERS FOR GENERAL EXTERNAL TURNING
Positive rake Negative rake
JSDJ2CR/L (P.13)
Shank size 10~12 mm
JSDJCR/L (P.13)
Shank size 8~16 mm
JSVJBR/L (P.13)
Shank size 10~16 mm
JSDNCN (P.14)
Shank size 8~16 mm
JSDN3CR/L (P.14)
Shank size 12~16 mm
Back side clampingWithout offset
Screw-on clampingWithout offset
Screw-on clampingWith offset
Screw-on clampingWith offset
Screw-on clampingWith offset
Screw-on clampingWith offset
JTDJ2CR/L (P.11)
Shank size 8~16 mm
JS-SDUCL (P.28)
Shank dia. φ19.05~25.4
JTDJ2NR/L (P.16)
Shank size 12~16 mm
●For External Profiling
Positive rake Negative rake
Screw-on clampingWithout offset
JSTACR/L (P.12)
Shank size 8~16 mm
Back side clampingWithout offset
JTTACR/L (P.11)
Shank size 8~16 mm
Back side clampingWithout offset
JTTANR/L (P.16)
Shank size 12~16 mm
Positive rake Negative rake
Screw-on clampingWithout offset
JSCL2CR/L (P.12)
Shank size 10~12 mm
Screw-on clampingWith offset
JSCLCR/L (P.12)
Shank size 8~16 mm
Back side clampingWithout offset
JTCL2CR/L (P.11)
Shank size 8~16 mm
Back side clampingWithout offset
JTCL2NR/L (P.16)
Shank size 12~16 mm
Screw-on clampingWith offset
JSCGCR/L (P.14)
Shank size 12~16 mm
Screw-on clampingWithout offset
JSCACR/L (P.15)
Shank size 8~12 mm
Screw-on clampingWith offset
JSCFCR/L (P.15)
Shank size 12~16 mm
Screw-on clampingWith offset
JSDFCR/L (P.15)
Shank size 12~16 mm
Screw-on clamping Back side clampingWithout offset
●For External Turning
●For External Turning and Facing
8
-
9
J-SERIES TOOLHOLDERS FOR FRONT, BACK, AND REVERSE TURNING
●For Reverse Turning ●For Front Turning
Max. depth of cut:5.5 mm
JSXGR/L (P.17)
Shank size 10~25 mm
Max. depth of cut:5.5 mm
JSXGR/L (P.17)
Shank size 10~25 mm
Max. depth of cut:5.5 mm
JSXBR/L (P.18)
Shank size 10~25 mm
Max. depth of cut:2.5 mm
JSTBR/L (P.19)
Shank size 10~16 mm
Max. depth of cut:3.0 mm
JSEGR/L (P.20)
Shank size 10~16 mm
●For Back Turning
Max. depth of cut:2.5 mm
JS-TBL3 (P.28)
Shank dia. φ19.05~25.4
-
10
J-SERIES TOOLHOLDERS FOR THREADING AND BORING
J-SERIES TOOLHOLDERS FOR GROOVING AND PARTING-OFF
●For Grooving and Parting-off
Groove width : 0.33~2.0 mm Max. groove depth : 0.7~5.5 mm
Groove width : 0.33~3.0 mm Max. groove depth : 0.7~2.6 mm
JSTGR/L (P.23)
Shank size 10~16 mm
JSVGR/L (P.22)
Shank size 10~16 mm
JS-TGL3 (P.29)
Shank dia. φ19.05~25.4
●For Grooving
Groove width : 0.7~2.0 mm Max.parting dia. : φ9~12
JSXGR/L (P.21)
Shank size 10~25 mmGroove width : 2.0 mm Max.parting dia. : φ20~32
JCGSSR/L (P.24)
Shank size 10~16 mm
JCCWSR/L (P.24)
Shank size 10~25 mm
JCGWSR/L (P.25)
Shank size 10~16 mm
Applicable pitch range:0.5~1 mm
JSTTR/L (P.26)
Shank size 10~16 mm
JSXBR/L (P.26)
Shank size 10~25 mm
JS-TTL3 (P.30)
Shank dia. φ19.05~25.4
Applicable pitch range:0.5~1 mm
Applicable pitch range:0.5~1 mm
Min. bore dia.φ5.5~7
JS08H-SEXPR/L (P.27)
Shank dia. φ8 ●For Threading
●For Boring
Groove width : 0.33~3.0 mm Max. groove depth : 0.7~2.6 mm
Groove width : 2.0 mm Max.parting dia. : φ20
Groove width : 2.0 mm Max.parting dia. : φ20
-
Application Prec. finishing Finish to medium Medium cutting StainlessChipbreaker 01 PS PM SS
Shape
(11) (11) (11) (11)Application Aluminum Prec. finishingChipbreaker PP J□□
Shape
(11) (08、11)
Clamp Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJTTACR/L0810K08 ● ●
TC□□0802□□8 10 125 10 8 10
JCP-1JTTACR/L1010K08 ● ● 10 10 125 10 10 10
JDS-3525 P-2FJTTACR/L1212M11 ● ●
TC□□1102□□12 12 150 12 12 12
JCP-2JTTACR/L1616M11 ● ● 16 16 150 12 16 16
Clamp Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJTDJ2CR/L0810K07 ● ●
DC□□0702□□8 10 125 14 8 10
JCP-2 JDS-3525 P-2FJTDJ2CR/L1010K07 ● ● 10 10 125 14 10 10JTDJ2CR/L1212M11 ● ●
DC□□11T3□□12 12 150 18 12 12
JCP-3 JDS-5040 P-2.5FJTDJ2CR/L1616M11 ● ● 16 16 150 18 16 16
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(07、11) (07、11) (07、11) (07、11)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(07、11) (07、11) (07、11) (07、11)
Clamp Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJTCL2CR/L0810K06 ● ●
CC□□0602□□8 10 125 12 8 10
JCP-2 JDS-3525 P-2FJTCL2CR/L1010K06 ● ● 10 10 125 12 10 10JTCL2CR/L1212M09 ● ●
CC□□09T3□□12 12 150 16 12 12
JCP-3 JDS-5040 P-2.5FJTCL2CR/L1616M09 ● ● 16 16 150 16 16 16
●Recommended chipbreaker
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(06、09) (06、09) (06、09) (06、09)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(06、09) (06、09) (06、09) (06、09)
External profiling
JTDJ2C R/L
Right hand (R) shown.Without offset
External turning
JTTAC R/L
●Recommended chipbreakerTurning•Facing
JTCL2C R/L
Right hand (R) shown.Without offset
●Recommended chipbreaker
J-SERIES TOOLHOLDERS FOR GENERAL EXTERNAL TURNING ■ JT-type (Positive, back-side clamping)
11
Without offset Right hand (R) shown.
Stock status ●: Stocked item
-
J-SERIES TOOLHOLDERS FOR GENERAL EXTERNAL TURNING ■ J-type (Positive, screw-on clamping)
12
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSCL2CR/L 1010K06 ● ●
CC□□0602□□10 10 125 12 10 10
CSTB-2.5 T-8F (T-8L)JSCL2CR/L 1212K06 ● ● 12 12 125 12 12 12
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(06) (06) (06) (06)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(06) (06) (06) (06)
●Recommended chipbreaker
JSCL2C R/L
( ): Optional parts
Turning•Facing
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSCLCR/L0808H06 ● ●
CC□□0602□□8 8 100 12 8 10
CSTB-2.5JSCLCR/L1010H06 ● ● 10 10 100 12 10 12
T-8F (T-8L)JSCLCR/L1212H09 ● ●
CC□□09T3□□12 12 100 16 12 16
CSTB-4SDJSCLCR/L1616H09 ● ● 16 16 100 16 16 20
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(06、09) (06、09) (06、09) (06、09)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(06、09) (06、09) (06、09) (06、09)
●Recommended chipbreakerTurning•Facing
JSCLC R/L
( ): Optional parts
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSTACR/L 0808K08 ● ●
TC□□0802□□8 8 125 10 8 8
CSTB-2L T-6F (T-6L)JSTACR/L 1010K08 ● ● 10 10 125 10 10 10JSTACR/L 1212K11 ● ●
TC□□1102□□12 12 125 12 12 12
CSTB-2.5 T-8F (T-8L)JSTACR/L 1616H11 ● ● 16 16 100 12 16 16
Application Prec. finishing Finish to medium Medium cutting StainlessChipbreaker 01 PS PM SS
Shape
(11) (11) (11) (11)Application Aluminum Prec. finishingChipbreaker PP J□□
Shape
(11) (08、11)
External turning
JSTAC R/L
( ): Optional parts
●Recommended chipbreaker
Without offset Right hand (R) shown.
Right hand (R) shown.
Stock status ●: Stocked item
Without offset Right hand (R) shown.
-
13
J-SERIES TOOLHOLDERS FOR GENERAL EXTERNAL TURNING ■ J-type (Positive, screw-on clamping)
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSDJ2CR/L 1010K07 ● ●
DC□□0702□□10 10 125 14 10 10
CSTB-2.5 T-8F (T-8L)JSDJ2CR/L 1212K07 ● ● 12 12 125 14 12 12
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(07) (07) (07) (07)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(07) (07) (07) (07)
●Recommended chipbreakerExternal profiling
JSDJ2C R/L
( ): Optional parts
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSVJBR/L 1010H11 ● ● 10 10 100 20 10 12JSVJBR/L 1212H11 ● ● VB□□1103□□ 12 12 100 22 12 16 CSTB-2.5 T-8F (T-8L)JSVJBR/L 1616H11 ● ● 16 16 100 22 16 20
Application Prec. finishing FinishingChipbreaker PS J□□
Shape
(11) (11)ApplicationChipbreaker
Shape
●Recommended chipbreakerExternal profiling
JSVJB R/L
( ): Optional parts
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSDJCR/L 0808H07 ● ●
DC□□0702□□8 8 100 14 8 10
CSTB-2.5JSDJCR/L 1212H07 ● ● 12 12 100 14 12 16JSDJCR/L 1010H11 ● ● 10 10 100 18 10 12 T-8F (T-8L)JSDJCR/L 1212H11 ● ● DC□□11T3□□ 12 12 100 18 12 16 CSTB-4SDJSDJCR/L 1616H11 ● ● 16 16 100 18 16 20
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(07、11) (07、11) (07、11) (07、11)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(07、11) (07、11) (07、11) (07、11)
External profiling
JSDJC R/L
( ): Optional parts
●Recommended chipbreaker
Without offset Right hand (R) shown.
Right hand (R) shown.
Right hand (R) shown.
Stock status ●: Stocked item
-
J-SERIES TOOLHOLDERS FOR GENERAL EXTERNAL TURNING ■ J-type (Positive, screw-on clamping)
14
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSCGCR/L 1212H06 ● ● CC□□0602□□ 12 12 100 12 12 16 CSTB-2.5
T-8F (T-8L)JSCGCR/L 1616H09 ● ● CC□□09T3□□ 16 16 100 16 16 20 CSTB-4SD
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(06、09) (06、09) (06、09) (06、09)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(06、09) (06、09) (06、09) (06、09)
●Recommended chipbreakerTurning•Facing
JSCGC R/L
( ): Optional parts
Clamping screw Wrench
Toolholder Cat. No. Stock Applicable insert.Dimensions (mm)
h b R1 R2 h1 fJSDNCN 0808H07 ● 8 8 100 14 8 4JSDNCN 1010K07 ● DC□□0702□□ 10 10 125 14 10 5 CSTB-2.5JSDNCN 1212K07 ● 12 12 125 14 12 6 T-8F (T-8L)JSDNCN 1212H11 ●
DC□□11T3□□12 12 100 21 12 6
CSTB-4SDJSDNCN 1616H11 ● 16 16 100 21 16 8
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(07、11) (07、11) (07、11) (07、11)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(07、11) (07、11) (07、11) (07、11)
External profiling
JSDNCN
( ): Optional parts
●Recommended chipbreaker
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(07、11) (07、11) (07、11) (07、11)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(07、11) (07、11) (07、11) (07、11)
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSDN3CR/L 1212H07 ● ● DC□□0702□□ 12 12 105 100 12 18 CSTB-2.5
T-8F (T-8L)JSDN3CR/L 1616H11 ● ● DC□□11T3□□ 16 16 107 100 16 25 CSTB-4SD
External profiling
JSDN3C R/L
( ): Optional parts
●Recommended chipbreaker
Right hand (R) shown.
Right hand (R) shown.
Stock status ●: Stocked item
-
J-SERIES TOOLHOLDERS FOR GENERAL EXTERNAL TURNING■ J-type (Positive, screw-on clamping)
15
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSCFCR/L 1212H06 CC□□0602□□ 12 12 100 16 12 16 CSTB-2.5
T-8F (T-8L)JSCFCR/L 1616H09 CC□□09T3□□ 16 16 100 16 16 20 CSTB-4SD
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(06、09) (06、09) (06、09) (06、09)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(06、09) (06、09) (06、09) (06、09)
●Recommended chipbreakerTurning•Facing
JSCFC R/L
( ): Optional parts
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSDFCR/L 1212H07 ● ● DC□□0702□□ 12 12 100 8 12 16 CSTB-2.5
T-8F (T-8L)JSDFCR/L 1616H11 ● ● DC□□11T3□□ 16 16 100 10.5 16 22 CSTB-4SD
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(07、11) (07、11) (07、11) (07、11)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(07、11) (07、11) (07、11) (07、11)
Turning•Facing
( ): Optional parts
●Recommended chipbreaker
JSDFC R/L
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSCACR/L 0808H06 ● ●
CC□□0602□□8 8 100 12 8 8
CSTB-2.5JSCACR/L 1010H06 ● ● 10 10 100 12 10 10 T-8F (T-8L)JSCACR/L 1212H09 ● ● CC□□09T3□□ 12 12 100 16 12 12 CSTB-4SD
Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(06、09) (06、09) (06、09) (06、09)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(06、09) (06、09) (06、09) (06、09)
●Recommended chipbreakerTurning•Facing
JSCAC R/L
( ): Optional parts
Right hand (R) shown.Without offset
Right hand (R) shown.
Right hand (R) shown.
Stock status ●: Stocked item
-
Clamp Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJTTANR/L 1216K16 ● ●
TN□□1604□□12 16 125 19.8 12 16
JCP-3N JDS-5040 P-2.5FJTTANR/L 1616K16 ● ● 16 16 125 19.8 16 16
Clamp Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJTCL2NR/L 1216K09
CN□□0903□□12 16 125 15.6 12 16
JCP-3N JDS-5040 P-2.5FJTCL2NR/L 1616K09 16 16 125 15.6 16 16
Clamp Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJTDJ2NR/L 1216K11
DN□□1104□□12 16 125 15.6 12 16
JCP-3N JDS-5040 P-2.5FJTDJ2NR/L 1616K11 16 16 125 15.6 16 16
J-SERIES TOOLHOLDERS FOR GENERAL EXTERNAL TURNING ■ JT-type (Negative, back-side clamping)
JTTAN R/L
JTCL2N R/L
JTDJ2N R/L
16
External turning
Turning•Facing
External profiling
Application Prec. finishing Prec. finishing Finishing FinishingChipbreaker 01 C P TS
Shape
(16) (16) (16) (16)ApplicationChipbreaker
Shape
●Recommended chipbreaker
Application Prec. finishingChipbreaker 01
Shape
(09)ApplicationChipbreaker
Shape
●Recommended chipbreaker
Application Prec. finishingChipbreaker 01
Shape
(11)ApplicationChipbreaker
Shape
●Recommended chipbreaker
Right hand (R) shown.
Right hand (R) shown.
Right hand (R) shown.
Stock status ●: Stocked item
Without offset
Without offset
Without offset
-
JXFR/L8000F
JXFR/L8010F
Coated Cermet UncoatedJ740 NS530 TH10R L R L R L
Insert Cat. No.
Dimensions (mm) Stocked grades
φd T RMax. depthof cut
Front turning•Reverse turning
JSXG R/L
( ): Optional parts
Right hand (R) shown.
J-SERIES TOOLHOLDERS FOR FRONT AND REVERSE TURNING■ JSXG-type (Commonly used for grooving and parting-off)
●Inserts ●JXF-type inserts for front turning (With sharp edge)
8 3.970.03
5.50.1
●
●
●Inserts
●
●
●
●
JXRR/L8000F
JXRR/L8010F
Coated Cermet UncoatedJ740 NS530 TH10R L R L R L
Insert Cat. No.
Dimensions (mm) Stocked grades
φd T RMax. depthof cut
●JXR-type inserts for reverse turning (With sharp edge)
8 3.970.03
5.50.1
●
●
●
●
●
●
Note: These toolholders can be also used for JXG-type grooving and parting-off inserts.
17
“-C”type
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 R3 h1 fJSXGR/L1010K8-C ● ● 10 10 125 29 6.7 10 10JSXGR/L1212K8-C ● ●
JXFR/L8□□□12 12 125 29 6.7 12 12
JSXGR/L1616K8 ● ●JXRR/L8□□□
16 16 125 29 6.5 16 16 CSTB-4SD T-8F (T-8L)JSXGR/L2020K8 ● ● 20 20 125 29 6.5 20 20JSXGR/L2525K8 ● ● 25 25 125 29 6.5 25 25
Right hand (R) shown.
Right hand (R) shown. Stock status ●: Stocked item
Can be wrenched from back side with double-socket Torx screw.
-
JXBR/L8005
JXBR/L8010
JXBR/L8015
Coated Cermet UncoatedJ740 NS530 TH10R L R L R L
JXBR/L8000F
JXBR/L8005F
JXBR/L8010F
JXBR/L8015F
R L R L R L
Dimensions (mm) Stocked grades
0.03
8 3.970.05
5.50.1
0.15
φd T RMax. depthof cut
( ): Optional parts
J-SERIES TOOLHOLDERS FOR BACK TURNING■ JSXB-type (Commonly used for threading)
●Inserts
Note: These toolholders can be also used for JXT-type threading inserts.
Back turning
JSXB R/L
Insert Cat. No.Coated Cermet UncoatedJ740 NS530 TH10
●
●
●
●
●
●
●
●
●
●
●JXB-type inserts (with honed edges)
Insert Cat. No.
Dimensions (mm) Stocked grades
φd T RMax. depthof cut
0.05
8 3.97 0.1 5.5
0.15
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●JXB-type inserts (with sharp edges)
18
“-C”type
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 R3 h1 fJSXBR/L1010K8-C ● ● 10 10 125 29 6.7 10 5.7JSXBR/L1212K8-C ● ● 12 12 125 29 6.7 12 7.7JSXBR/L1616K8 ● ● JXBR/L8□□□ 16 16 125 29 6.4 16 11.7 CSTB-4SD T-8F (T-8L)JSXBR/L2020K8 ● ● 20 20 125 29 6.4 20 15.7JSXBR/L2525K8 ● ● 25 25 125 29 6.4 25 20.7
Right hand (R) shown.
Right hand (R) shown.
Stock status ●: Stocked item
Can be wrenched from back side with double-socket Torx screw.
-
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 f cJSTBR/L1010K3 ● ● 10 10 125 15 10 6 5JSTBR/L1212K3 ● ● JTBR/L3□□□ 12 12 125 15 12 8 3 CSTB-4SD T-8F (T-8L)JSTBR/L1616K3 ● ● 16 16 125 15 16 12 -
J-SERIES TOOLHOLDERS FOR BACK TURNING■ JSTB-type
Back turning
JSTB R/L
( ): Optional parts
Right hand (R) shown.
●Inserts
Right hand (R) shown.
JTBR/L3000F
JTBR/L3005F
JTBR/L3010F
JTBR/L3015F
R L R L R L
Dimensions (mm) Stocked grades
0.03
9.438 3.180.05
2.50.1
0.15
φd T RMax. depthof cut
Insert Cat. No.Coated Cermet UncoatedJ740 NS530 TH10
●
●
●
●
●
●
●
●
●
●
●JTB-type inserts (with honed edges)
●
●
●
●
●
●
●JTB-type inserts (with sharp edges)
●
●
●
●
●
●
●
●
R L
Dimensions (mm) Stocked grades
φd T RMax. depthof cut
Coated Cermet UncoatedJ530 J740 NS530 TH10
2.5
R L R L R L
0.05
0.1
0.15
JTBR/L3005
JTBR/L3010
JTBR/L3015
9.438
Insert Cat. No.
3.18
●
●
●
19
Can be wrenched from back side with double-socket Torx screw.
Stock status ●: Stocked item
-
●
●
●
●
●
●
●
●
●
●
●
●
0.050.10.15
J10ER/L005BFJ10ER/L010BFJ10ER/L015BF
J-SERIES TOOLHOLDERS FOR BACK TURNING■ JSEG-type
Back turning
JSEG R/L
( ): Optional parts
●Inserts
Right hand (R) shown.
R L
Dimensions (mm) Stocked grades
6.35
φd T RMax. depthof cut
Insert Cat. No.Coated Cermet Uncoated
J530 J740 NS530 TH10
●J10E-type inserts (with sharp edges)
3.18 < 3
R L R L R L
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSEGR/L1010K10 ● ● 10 10 125 - 10 7.5JSEGR/L1212K10 ● ● J10ER/L□□□B□ 12 12 125 - 12 9.5 CSTB-2.5 T-8F (T-8L)JSEGR/L1616K10 ● ● 16 16 125 - 16 13.5
●
●
●
●
●
●
●
●
0.050.10.15
J10ER/L005BJ10ER/L010BJ10ER/L015B
R L
Dimensions (mm) Stocked grades
6.35
φd T RMax. depthof cut
Insert Cat. No.Coated Cermet Uncoated
J530 J740 NS530 TH10
●J10E-type inserts (with honed edges)
3.18 < 3
R L R L R L
20
Right hand (R) shown.
Stock status ●: Stocked item
-
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
JXGR/L8070FAJXGR/L8070FA-005JXGR/L8100FAJXGR/L8100FA-005JXGR/L8100FA45JXGR/L8100FA45-005JXGR/L8120FAJXGR/L8150FAJXGR/L8150FA-005JXGR/L8150FA50JXGR/L8150FA50-005JXGR/L8180FAJXGR/L8180FA-005JXGR/L8200FAJXGR/L8200FA-005JXGR/L8200FNJXGR/L8200FN-005
R L R L R L
Dimensions (mm) Stocked grades
φd T W+0.05
θMax.
0 groove Rdepth
( ): Optional parts
J-SERIES TOOLHOLDERS FOR GROOVING■ JSXG-type
●Inserts
Right hand (R) shown.
Grooving • Parting-off
JSXG R/L
Insert Cat. No.Coated Cermet UncoatedJ740 NS530 TH10
●JXG-type inserts (with sharp edges)
21
These toolholders are also used for JXF- and JXR-type inserts.
“-C”type
8 3.97
0.7
1
1.2
1.5
1.8
2
15゜
0゜
4.5
6
4.5
6
5
6
00.0500.0500.05000.0500.0500.0500.0500.05
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
(2-corner type)
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 R3 h1 fJSXGR/L1010K8-C ● ● 10 10 125 29 6.7 10 10JSXGR/L1212K8-C ● ● 12 12 125 29 6.7 12 12JSXGR/L1616K8 ● ● JXGR/L8□□□ 16 16 125 29 6.5 16 16 CSTB-4SD T-8F (T-8L)JSXGR/L2020K8 ● ● 20 20 125 29 6.5 20 20JSXGR/L2525K8 ● ● 25 25 125 29 6.5 25 25
Stock status ●: Stocked item
Can be wrenched from back side with double-socket Torx screw.
Right hand (R) shown.
-
22
●
●
0
0.33
0.5
0.75
0.95
1
1.25
1.5
2
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJSVGR/L1010K-C ● ● 10 10 125 23 10 10JSVGR/L1212K-C ● ● JVGR/L□□□ 12 12 125 23 12 12 CSTB-3S T-9F (T-9L)JSVGR/L1616K ● ● 16 16 125 23 16 16
Grooving
JSVG R/L
( ): Optional parts
J-SERIES TOOLHOLDERS FOR GROOVING■ JSVG-type
●
●
●
●
●
●
●
●
JVGR/L033F
JVGR/L050F
JVGR/L075F
JVGR/L095F
JVGR/L100F
JVGR/L125F
JVGR/L150F
JVGR/L200F
R L R L R L
Dimensions (mm) Stocked grades
φd T W+0.05
GMax.
0 groove Rdepth
●Inserts
Right hand (R) shown.
Insert Cat. No.Coated Cermet UncoatedJ740 NS530 TH10
●JVG-type inserts (with sharp edges)
7.94 3.18
0.8
1.2
2
6
5.5
6
0.7
1.1
1.9
5.5
5
5.5
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
(2-corner type)
●Standard cutting conditions (Grooving)
J740
NS530J530
TH10
General steelsStainless steelsFree-cutting steelsGeneral steelsStainless steels
Aluminum, copper alloysDifficult-to-cut materials such as titanium alloys
Grade
10-50-100 0.01-0.05-0.1
50-80-150 0.01-0.05-0.1
10-80-200 0.01-0.05-0.110-20-30 0.01-0.05-0.1
“-C”type
Stock status ●: Stocked item
Work material Cutting speed Vc (m/min) Feed f (mm/rev)
Right hand (R) shown.
-
0.330.430.50.650.750.80.850.951.01.11.21.251.31.41.451.51.751.82.02.252.52.753.0
0.81.21.2
2
2.2
2.7
0.71.11.1
1.9
2.1
2.6
●●●●●●●●●●●●●●●●●●●●●●●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
JTGR/L3033FJTGR/L3043FJTGR/L3050FJTGR/L3065FJTGR/L3075FJTGR/L3080FJTGR/L3085FJTGR/L3095FJTGR/L3100FJTGR/L3110FJTGR/L3120FJTGR/L3125FJTGR/L3130FJTGR/L3140FJTGR/L3145FJTGR/L3150FJTGR/L3175FJTGR/L3180FJTGR/L3200FJTGR/L3225FJTGR/L3250FJTGR/L3275FJTGR/L3300F
23
Grooving
JSTG R/L
J-SERIES TOOLHOLDERS FOR GROOVING■ JSTG-type
●Inserts
Right hand (R) shown.
(3-corner type)
●Inserts
Right hand (R) shown.
Can be wrenched from back side with double-socket Torx screw.
0.03
0.05
R L R L R L
Dimensions (mm) Stocked grades
φd T W+0.05
GMax.
0 groove Rdepth
Coated Cermet UncoatedJ530 J740 NS530 TH10
●JTG-type inserts (with sharp edges)
9.525 3.18
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 f cJSTGR/L1010K3 ● ● 10 10 125 18.5 10 10 2JSTGR/L1212K3 ● ● JTGR/L3□□□ 12 12 125 18.5 12 12 - CSTB-4SD T-8F (T-8L)JSTGR/L1616K3 ● ● 16 16 125 18.5 16 16 -
R L
0.330.50.750.9511.251.451.51.7522.5
0.81.2
2
2.2
2.7
0.71.1
1.9
2.1
2.6
●●●●●●●
JTGR/L3033JTGR/L3050JTGR/L3075JTGR/L3095JTGR/L3100JTGR/L3125JTGR/L3145JTGR/L3150JTGR/L3175JTGR/L3200JTGR/L3250
0.03
0.05
R L R L R L
Dimensions (mm) Stocked grades
φd T W+0.05
GMax.
0 groove Rdepth
Insert Cat. No.Coated Cermet Uncoated
J530 J740 NS530 TH10
●JTG-type inserts (with honed edges)
9.525 3.18
R L
●●●●●●●
Insert Cat. No.
( ): Optional parts
Right hand (R) shown.
Stock status ●: Stocked item
-
24
Stocked gradesCoated Cermet
T9025 GH730 NS530
00.0500.05
24.8 15-
15゜
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJCCWSR/L1010K2 ● ● 10 10 125 19 10 10 20JCCWSR/L1212K2 ● ● 12 12 125 19 12 12 20JCCWSR/L1616K2 ● ● JCC□200□ 16 16 125 19 16 16 20 CSTB-4S T-15F (T-15L)JCCWSR/L2020K2 ● ● 20 20 125 19 20 20 20JCCWSR/L2525K2 ● ● 20 25 125 19 25 25 20
■ JCCWS-type
Clamping screw Wrench
Groove Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
width R L b h h1 L R fJCGSSR/L1010-20 ● ● 10 10 10 125 15 10.2 20
2 JCGSSR/L1212-20 ● ● GE20 12 12 12 125 19 12.2 25 CSTB-3 T-9FJCGSSR/L1616-20 ● ● 16 16 16 125 22.5 16.2 32
Grooving • Parting-off
JCGSS R/L
J-SERIES TOOLHOLDERS FOR GROOVING AND PARTING-OFF■ JCGSS-type
Right hand (R) shown.
●Inserts
Right hand (R) shown.
GE20
InsertCat. No.
Dimensions (mm)
● ● ●
Grooving • Parting-off
JCCWS R/L
Right hand (R) shown.
●JCC-type inserts (with sharp edge)
●
R L
Dimensions (mm) Stocked grades
T W L R θCoated Cermet Uncoated
J530 J740 NS530 TH10R L R L R L
JCCN200FJCCN200F-005JCCR/L200FJCCR/L200F-005
●Inserts
Right hand (R) shown.
●
●
●
(2-corner type)
● ●
●
●
2 10 3.5 0.2
W L h R
Insert Cat. No.
● ●
●
●
Max.parting-offdia. φ D
Max.parting dia.φ D
( ): Optional parts
Stock status ●: Stocked item
-
25
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 fJCGWSR/L1010K2 ● ● 10 10 125 19.5 10 10 20JCGWSR/L1212K2 ● ● JCGN200□ 12 12 125 19.5 12 12 20 CSTB-4S T-15F (T-15L)JCGWSR/L1616K2 ● ● 16 16 125 19.5 16 16 20
●
Grooving • Parting-off
JCGWS R/L
J-SERIES TOOLHOLDERS FOR GROOVING AND PARTING-OFF■ JCGWS-type
Right hand (R) shown.
●Inserts
Right hand (R) shown.
●JCG-type inserts (with sharp edges)
● ●●●
R L
Dimensions (mm) Stocked grades
T W L RCoated Cermet Uncoated
J530 J740 NS530 TH10
0.05
R L R L R L
20JCGN200F
JCGN200FR/L3
Insert Cat. No.
2
( ): Optional parts
(2-corner type)
●
● ●●
Max.parting dia.φ D
Stock status ●: Stocked item
-
●JTT-type inserts (with sharp edges)
26
Clamping screw Wrench
Toolholder Cat. No.Stock Applicable insert.
Dimensions (mm)R L h b R1 R2 R3 h1 f
JSXBR/L1010K8-C ● ● 10 10 125 29 6.7 10 5.7JSXBR/L1212K8-C ● ● 12 12 125 29 6.7 12 5.7JSXBR/L1616K8 ● ● JXT□R/L□□□□□ 16 16 125 29 6.4 16 11.7 CSTB-4SD T-8F (T-8L)JSXBR/L2020K8 ● ● 20 20 125 29 6.4 20 15.7JSXBR/L2525K8 ● ● 25 25 125 29 6.4 25 20.7
9.525
Threading
JSTT R/L
( ): Optional parts
J-SERIES TOOLHOLDERS FOR THREADING■ JSTT-type
Right hand (R) shown.
Can be wrenched from back side with double-socket Torx screw.
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L h b R1 R2 h1 f cJSTTR/L1010K3 ● 10 10 125 16.5 10 9.5 2JSTTR/L1212K3 ● JTTR/L30□□□ 12 12 125 16.5 12 11.5 - CSTB-4SD T-8F (T-8L)JSTTR/L1616K3 ● 16 16 125 16.5 16 15.5 -
●Inserts
●
●
●
●
●
R L
Dimensions (mm) Stocked grades
θ φd S RCoated Cermet Uncoated
J530 J740 NS530 TH10R L R L R L
JTTR/L3005FJTTR/L3010FJTTR/L3005F-55
60゜
55゜
●
●3.180.050.100.05
8
Threading
JSXB R/L
( ): Optional parts
Right hand (R) shown.
●Inserts ●JXT-type inserts (with sharp edges)
●
●
●
●
R L
Dimensions (mm) Stocked grades
θ φd S RCoated Cermet Uncoated
J530 J740 NS530 TH10R L R L R L
JXT1R/L6000FJXT2R/L6000FJXT3R/L6000F
60゜
Insert Cat. No.
●
●3.97 0.03
Insert Cat. No.
■ JSXB-type
Machinable pitch range P=0.5 - 1.0 mm
Figures at left show right hand (R) inserts. Right hand toolholders use right hand insert and left hand toolholdersuse left hand insert.
Can be wrenched from back side with double-socket Torx screw.
These toolholders are also used for back turning.
Right hand (R) shown. Stock status ●: Stocked item
Stock status ●: Stocked item
-
27
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert Dimensions (mm)
R LJS08H-SEXPR/L045 ●JS08H-SEXPR/L047 ●
EP□□0401□□
Boring • Internal facing
JS08H-SEXPR/L
J-SERIES TOOLHOLDERS FOR BORING■ Steel-shank S-type (Positive, screw-on clamping)
Right hand (R) shown.
Min.bore dia.φ D
●BLM type sleeves (Round shank)
φd
Std.corner
rc f R1 R2 h b α゜ a5.570.40.4
882.73.55
100100
1620
77
--
12゜12゜
--
CSTB-2 T-6F
BLM19-08BLM20-08BLM22-08BLM254-08
●Applicable sleeves
Sleeve Cat. No. StockDimensions (mm)
φd R b hApplicable shank dia.
φD
8
19.05 100 18 1820 100 19 1822 125 21 2125.4 125 24 24
●
●
●
●
●
●
●
Appearance Insert Cat. No.I.C. dia. Thickness Hole dia.
Dimensions (mm)J740
R L
Stocked grades
EPGT040100R/L-J08EPGT040102R/L-J08EPGT040104R/L-J08
3.97 1.590.030.20.4
●Inserts
Coated
Corner R
2.3
Stock status ●: Stocked item
-
●
●
●
●
0.03
9.438 3.180.05
2.50.10.15
28
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insert.Dimensions (mm)
R L φd f R1 h BJS19K-TBL3 ● 19.05 6 125 18 11.5JS20K-TBL3 ●
JTBR30□□20.00 6 125 19 11.5
CSTB-4S T-15FJS22K-TBL3 ● 22.00 6 125 21 11.5JS25K-TBL3 ● 25.40 10 125 24 12.7
J-SERIES TOOLHOLDERS FOR BACK TURNING (ROUND SHANK)■ JS-TBL3-type
Left hand (L) shown.
Back turning
●Inserts
Right hand (R) shown.
JTBR/L3000FJTBR/L3005FJTBR/L3010FJTBR/L3015F
R L R L R L
Dimensions (mm) Stocked grades
φd T RMax.depthof cut
Inserat Cat. No.Coated Cermet UncoatedJ740 NS530 TH10
●
●
●
●
●
●
●JTB-type inserts (with honed edges)
●
●
●
●
●
●
●JTB-type inserts (with sharp edges)
●
●
●
●
●
●
●
●
R L
Dimensions (mm) Stocked grades
φd T RMax.depthof cut
Coated Cermet UncoatedJ530 J740 NS530 TH10
2.5
R L R L R L0.050.10.15
JTBR/L3005JTBR/L3010JTBR/L3015
9.438 3.18
●
●
●
JS-TBL3
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insertDimensions (mm)
R L φd f R1 h B GJS19K-SDUCL07 19.05 6 125 18 11.5 -JS20K-SDUCL07 DC□□0702□□ 20.00 6 125 19 11.5 - CSTB-2.5JS22K-SDUCL07 22.00 6 125 21 11.5 -JS19K-SDUCL11 19.05 10 125 18 11.5 1.525 T-8FJS20K-SDUCL11
DC□□11T3□□20.00 10 125 19 11.5 1.000
CSTB-4SDJS22K-SDUCL11 22.00 11 125 21 11.5 1.000JS25K-SDUCL11 25.40 12 125 24 12.7 0.700
J-SERIES TOOLHOLDERS FOR EXTERNAL PROFILING (ROUND SHANK)■ JS-SDUCL-type
Left hand (L) shown.
External profiling Application Prec. finishing Finishing Finish to medium Medium cuttingChipbreaker 01 PF PS PM
Shape
(07、11) (07、11) (07、11) (07、11)Application Aluminum Aluminum Prec. finishing Finish to mediumChipbreaker PP (T-DIA) J□□ -
Shape
(07、11) (07、11) (07、11) (07、11)
● Recommended chipbreaker
JS-SDUCL
●
●
●
●
●
●
●
Note:Left hand (L) toolholders use right hand (R)insert and right hand (R) toolholders use lefthand insert.
Stock status ●: Stocked item
Inserat Cat. No.
Stock status ●: Stocked item
-
●JTG-type inserts (with sharp edges)
29
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insertDimensions (mm)
R L φd f R1 h bJS19K-TGL3 ● 19.05 6 125 18 11.5JS20K-TGL3 ●
JTGR3□□□20.00 6 125 19 11.5
CSTB-4S T-15FJS22K-TGL3 ● 22.00 6 125 21 11.5JS25K-TGL3 ● 25.40 10 125 24 12.7
J-SERIES TOOLHOLDERS FOR GROOVING (ROUND SHANK)■ JS-TGL3-type
Grooving
0.330.430.50.650.750.80.850.951.01.11.21.251.31.41.451.51.751.82.02.252.52.753.0
0.8
1.2
2
2.2
2.7
0.7
1.1
1.9
2.1
2.6
●●●●●●●●●●●●●●●●●●●●●●●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
●
●
●
●●
●
●●●
●
●
JTGR/L3033FJTGR/L3043FJTGR/L3050FJTGR/L3065FJTGR/L3075FJTGR/L3080FJTGR/L3085FJTGR/L3095FJTGR/L3100FJTGR/L3110FJTGR/L3120FJTGR/L3125FJTGR/L3130FJTGR/L3140FJTGR/L3145FJTGR/L3150FJTGR/L3175FJTGR/L3180FJTGR/L3200FJTGR/L3225FJTGR/L3250FJTGR/L3275FJTGR/L3300F
( ): Optional parts
●Inserts
Right hand (R) shown.
●Inserts
Right hand (R) shown.
0.03
0.05
R L R L R L
Dimensions (mm) Stocked grades
φd T W+0.05
GMachinable
0 groove Rdepth
Coated Cermet UncoatedJ530 J740 NS530 TH10
9.525 3.18
R L
●JTG-type inserts (with honed edges)
Insert Cat. No.
0.330.50.750.9511.251.451.51.7522.5
0.81.2
2
2.2
2.7
0.71.1
1.9
2.1
2.6
●●●●●●●
JTGR/L3033JTGR/L3050JTGR/L3075JTGR/L3095JTGR/L3100JTGR/L3125JTGR/L3145JTGR/L3150JTGR/L3175JTGR/L3200JTGR/L3250
0.03
0.05
R L R L R L
Dimensions (mm) Stocked grades
φd T W+0.05
GMachinable
0 groove Rdepth
Insert Cat. No.Coated Cermet Uncoated
J530 J740 NS530 TH10
9.525 3.18
R L
●●●●●●●
JS-TGL3
Left hand (L) shown.
Note:Left hand (L) toolholders use right hand (R)insert and right hand (R) toolholders use lefthand insert.
Note:Left hand (L) toolholders use right hand (R)insert and right hand (R) toolholders use lefthand insert.
Stock status ●: Stocked item
-
30
Clamping screw Wrench
Toolholder Cat. No.Stock
Applicable insertDimensions (mm)
R L φd f R1 h bJS19K-TTL3 ● 19.05 10 125 18 11.5JS20K-TTL3 ●
JTTR30□□20.00 10 125 19 11.5
CSTB-4S T-15FJS22K-TTL3 ● 22.00 10 125 21 11.5JS25K-TTL3 ● 25.40 10 125 24 12.7
J-SERIES TOOLHOLDERS FOR THREADING (ROUND SHANK)■ JS-TTL3-type
Threading
9.525
( ): Optional parts
●Inserts
Right hand (R) shown.
●JTT-type inserts (with sharp edges)
●
●
●
●
●
R L
Dimensions (mm) Stocked grades
θ φd S RCoated Cermet Uncoated
J530 J740 NS530 TH10R L R L R L
JTTR/L3005FJTTR/L3010FJTTR/L3005F-55
60゜
55゜
●
●3.180.050.100.05
Insert Cat. No.
Machinable pitch range: P=0.5~1.0 mm
JS-TTL3
Left hand (L) shown.
Stock status ●: Stocked itemNote:Left hand (L) toolholders use right hand (R)insert and right hand (R) toolholders use lefthand insert.
-
Distributed by:
Head OfficeSolid Square, 580 Horikawa-Cho, Saiwai-Ku, Kawasaki, 212-8503 JapanPhone: +81-44-548-9500 Facsimile: +81-44-548-9540
International Operations DivisionKokusai Shin-Kawasaki Bldg., 2-1-5 Kitakase, Saiwai-Ku,Kawasaki, 212-0057 JapanPhone: +81-44-587-2562 Facsimile: +81-44-587-2580Sales of machining tools
Tungaloy America, Inc.1226A Michael Drive, Suite A, Wood Dale, IL.60191, U.S.A.Phone: +1-630-227-3700 Facsimile: +1-630-227-0690Sales of machining tools
Tungaloy Europe GmbHElisabeth-Selbert-Strasse 3, 40764 Langenfeld, GermanyPhone: +49-2173-90420-0 Facsimile: +49-2173-90420-18Sales of machining tools
Tungaloy France S.a.r.l.6 Avenue des Andes, 91952 Courtaboeuf Cedex, FrancePhone: +33-1-6486-4300 Facsimile: +33-1-6907-7817Sales of machining tools
Tungaloy Italia S.p.A.Via E. Andolfato 10, 20126 Milano, ItalyPhone: +39-02-252012-1 Facsimile: +39-02-252012-65Sales of machining tools
Tungaloy Cutting Tool (Shanghai) Co.,LtdUnited Plaza 1505, 1468 Nan Jing Road West, Shanghai 200040, ChinaPhone: +86-21-6247-0512 Facsimile: +86-21-6289-1302Sales of machining tools
Thai Tungaloy Cutting Tool Co.,Ltd11th Floor, Sorachai Bldg. 23/7, Soi Sukhumvit 63,Klongtonnue, Wattana Bangkok 10110, ThailandPhone: +66-2-714-3130 Facsimile: +66-2-714-3134Sales of machining tools
Tungaloy Singapore(Pte.),Ltd50 Kallang Avenue #06-03 Noel Corporate Building Singapore 339505Phone:+65-6391-1833 Facsimile:+65-6299-4557Sales of machining tools
Tungaloy Australia Pty. Ltd.Suite 3, Compark Circuit, Mulgrave Vic. 3170, Melbourne, AustraliaPhone:+61-3-9560-5088 Facsimile:+61-3-9560-5077Sales of machining tools
Tungaloy De Mexico S.A.Calle Los Arellano #113 Parque Industrial Siglo, XXI
Aquascalientes, Ags. Mexico C.P. : 20290Phone:+52-4499-295410 Facsimile:+52-4499-295411Sales of machining tools
ISO 9001 certifiedQCOOJ005618/10/1996Tungaloy Co.Ltd
ISO 14001 certifiedEC97J1123Production Division,Tungaloy Co.Ltd
2005.6(BUN)