U1-1

MISSION:

U1-2

DELIVERABLES-UPDATE 1:

Team minutes from this Team Time MUST be submitted by email TODAY (the day of your

Team Time) to Mr. Touchton.

Individual multi-copter design concepts from each member.

Initial team collaborative multi-copter design concept. (Now in MI2)

Preliminary cardboard model/mockup of initial team multi-copter concept. (Now in MI2)

Team member assignments (i.e. Pilot, Solderer/Assembler, Draftsmen, Leader/Documenter)

o Each position MUST attend related workshops before/after school or Saturday (TBD)

DESIGN POINTS THAT ARE REQUIRED FOR ALL MULTI-COPTER DESIGNS:

Propellers must have a MINIMUM clearance of 4-inches over 360°

Each propeller ideally generates a maximum of 1000g of thrust at maximum RPM

ALL wiring must be accounted for in hard wiring diagrams BEFORE being connected

DESIGN POINTS THAT ARE RECOMMENDED FOR ALL MULTI-COPTER DESIGNS:

Motor torque should be balanced across the multi-copter

Gross vehicle weight should be kept below 60% maximum propeller thrust

Keep your center of mass as close to the geometric center of thrust as possible

SAFETY POINTS REQUIRED FOR ALL TEAM MEMBERS WITHIN 3 FEET OF ACTIVE MULTI-COPTER:

Safety glasses MUST BE ON when soldering

Safety glasses MUST BE ON when wiring

Safety glasses MUST BE ON when connecting batteries

Safety glasses MUST BE ON when flying multi-copter

Remote control MUST be visually verified to be OFF before connecting battery

ALL members MUST be clear of multi-copter BEFORE activating remote control

Team member clearance from multi-copter MUST be visually AND verbally verified

Soldering iron MUST be unplugged when not attended or being used within 1 minute

ALL plugged power contacts must be verified by 2 team members BEFORE connection

ALL battery and camera straps must be verified by 2 team members BEFORE flight

Everyone within 3-feet of cutting/soldering/filing etc. MUST have on safety glasses.

U1-3

Kit of Parts for electronics ONLY (All body parts will be designed and manufactured)

hexTronik DT750 Brushless Outrunner 750kv (4)

Turnigy Multistar 30 Amp Multi-rotor Brushless ESC 2-4S (4)

3.5mm Male/Female Bullet Brushless Motor Extension Lead 200mm (4)

HXT 4mm to 4 X 3.5mm bullet Multistar ESC Power Breakout Cable (1)

Hex locknuts M4 10pc (1)

Turnigy 4mm Heat Shrink Tube - BLACK (1mtr) (2)

3.5mm Male/Female Bullet Brushless Motor Extension Lead 200mm (4)

HXT 4mm to 4 X 3.5mm bullet Multistar ESC Power Breakout Cable (1)

Hex locknuts M4 10pc (1)

Turnigy 4mm Heat Shrink Tube - BLACK (1mtr) (2)

U1-4

PolyMax 3.5mm Gold Connectors 10 PAIRS (20PC) (2)

Hobbyking KK2.0 Multi-rotor LCD Flight Control

Board (1)

10CM Male to Male Servo Lead (JR) 26AWG (10pcs/set) (1)

OrangeRx R610 Spektrum DSM2 6Ch 2.4Ghz Receiver (w/ Sat Port) (1)

OrangeRx R100 Satellite Receiver (1)

Slow Fly Electric Prop 11x4.7R SF (4 pc - Green Right Hand Rotation) (1)

Slow Fly Electric Prop 11x4.7SF (4 pc - Green) (1)

Scorpion Lipoly Lock Strap 205mm (Small) x 3 (1)

Socket Head Bolt 3x25mm (10 pack)(6)

Hex locknuts M3 10pc (6)

Turnigy nano-tech 3000mah 3S 25~50C Lipo

Pack (2)

U1-5

Quattro 4x6S Charge/Balance board (2) This item will not be in your kit, for all to

use

HXT 4MM to Banana Plug Charge Lead Adapter(8) This item will not be in your kit, for all to

use

HobbyKing 540w 100~120v Power Supply (13.8v~18v - 30amp) (2) This item will not be in your kit, for all to

use

Turnigy Multistar ESC Programming Card (4) This item will not be in your kit, for all to use

Fat Shark PredatorV2 RTF FPV Headset System w/Camera and 5.8G TX (1) This item will not be in your kit, for all to use

5.8GHz Circular Polarized spiroNet Antenna (2) This item will not be in your kit, for all to use

GoPro HD HERO2: Outdoor Edition (1) This item will not be in your kit, for all to use

Turnigy 6S Mini Lipo Battery monitor. (2) This item will not be in your kit, for all to use

U1-6