uploads_downloads_construction carpenter, oss, l-1

- - 1

JOB SPECIFICATION AND

SKILL TEST

JOB TITLE : CONSTRUCTION CARPENTER (L-1) (ASSISTANT CARPENTER)

SECTOR : CIVIL ENGINEERING SUB-SECTOR : ALL

Council For Technical Education and Vocational Training NATIONAL SKILL TESTING BOARD

Kathmandu, NEPAL 2000

- - 2

The National Skill Standard and Test was developed by :

1. Mr. Narayan Dutta Sharma Adviser Chief Engineer Department of Road

2. Mr Bhim Raj Thapa Co-ordinator Superintending Engineer Department of Road

3. Mr Chhatra Bir Bajracharya Member Secretary Technical Officer, STD

4. Mr Babu Kazi Bajracharya Member Carpentry Workshop Incharge I.O.E.

5. Mr Jhanak Bahadur Shahi Member Supervisor, N.C.C.N

Approved by the tripartite National Skill Testing Board. 1989

- - 3

The National Skill Standard and Test is revised by : S. NO. NAME

DESIGNATION ORGANIZATION

1 Mr. Ishwer Raj Onta

Co-Ordinator Director, East Consult Pvt. Ltd., Lazimpat

2 Mr. Harihar Thapaliya

Member Director, Skill Testing Division, CTEVT, Sanothimi, Bhaktapur

3 Mr. G.N. Jha

Member secretary Skill Testing Division, CTEVT, Sanothimi, Bhaktapur

4 Mr Sahadev Prajapati

Subject Expert Sr. Instructor, Carpentry Trade, Sanothimi Campus, Bhaktapur

5 Mr Babu Kazi Bajracharya

Subject Expert Carpentry Workshop Incharge I.O.E.

6 Mr Sanu Raja Shilpakar

Subject Expert Director, Wood Seasoning Pvt. Ltd. Patan Industrial Estate, Lagankhel

7 Mr. Dobbar Lal Shilakar

Subject Expert Principal, Panauti Technical School, Panauti, Kavre

8 Er. Bishwanand Mishra

Consultant Engineer Engineer, Kathmandu

2000

- - 4

The National skill standard and Test was Reviseed by: 1

Er. Iswer Raj Onta

Coordinator

Founder Director East Consultant, KTM

2

Mr. Chandra Bhakta Nakarmi

Member

Director, National Skill Testing Board, CTEVT

3

Mr Shahdev Prajapati

Member / Expert

Reader, Sanothimi Campus, Sanothimi, Baktapur.

4

Mr Sanu Kaji Sthapit

Member / Expert

General Manager, 11S Furniture, Ganabahal, KTM.

5

Mr. Dober lal Shilakar

Member / Expert

Principal, Banepa Polytechnic, Banepa

6

Er Dhurba Raj Poudel

Member / Expert

Engineer, Access Engineering Consultancy, Kathmandu

7

Mr Ram Hari Devkota

Member

Dy-Director, National Skill Testing Board, CTEVT

8

Mr Ishwar Chandra Ghimire

Member

Skill Testing Officer, National Skill Testing Board, CTEVT

9

Er Guna Nanda Jha

Member Secretary

Skill Testing Officer, National Skill Testing Board, CTEVT

Approve by the tripartite National Skill Testing Board.

2009

- - 5

JOB SPECIFICATION 1. JOB TITLE : CONSTRUCTION CARPENTER L-1

LEVEL : 1

2. JOB DESCRIPTION

A construction carpenter as per instruction prepares different type of wood stock, wooden members and laminating to required

prepared size and installs panels, simple common hardware accessories to the wooden fixtures and prepares lay-out, walling materials and surfaces for painting & cleans working area.

3 LIST OF TASK 1 Preparing wood stock and laminating members for the construction of various fixtures as per instruction.

2 Installing different types of prepared window/ door panels, shutter, sliding door/window.

3 Cutting ply-wood, teak ply, metalic sheet, plain wooden panel board other boards and wire mesh to required sized and

installing them in the frames.

4 Installing simple common hardware accessories to the wooden fixtures.

5 Preparing wooden pegs ( Pointed posts ), corner posts, levelling pegs, poling boards, wedges, struts, vertical and horizontal sheeting ( for laying timbering in foundation).

6 Preparing surfaces for painting.

4

QUALIFYING NOTES

Normal health, no special physical (strength) requirement demanded by this job.

Educational requirement: able to read, write and understand specifications & instruction.

- - 6

TASK SPECIFICATION 5 TASK NO. : 1

JOB TITLE : CONSTRUCTION CARPENTER L-1 PREPARING WOOD STOCK AND LAMINATING MEMBERS FOR THE CONSTRUCTIONS OF VARIOUS

WOODEN FIXTURES AS PER INSTRUCTION. 6 TASK ELEMENTS

1.1 Receives verbal instructions/sketches.

1.2 Select and/ or collects appropriate hand tools, equipment and required materials.

1.3 Sharpens different cutting tools.

1.4 Marks on wooden piece as per instruction.

1.5 Cuts previously marked stock to appropriate length and breadth.

1.6 Assists on planning wood stock.

1.7 Houses previously marked simple wooden joints by chiseling and sawing.

1.8 Joins wooden members to increase the required size, for temporary work (trial fitting).

1.9 Assemble the prepared joints.

1.10 Cleans the work area.

- - 7

TASK SPECIFICATION 7 TASK PERFORMANCE REQUIREMENTS

Instructions/sketch, folding rule, measuring tape, try square, marking gauge, mortise gauge, saw, jack plane, smooth plane, block plane, rebate plane, tongue and groove plane, plough plane, adze, mallet, chisel , bar-clamp, bench vice, c-clamp, oil stone, wedges, brace or portable power tools, sandpaper, nails, screws, screw-driver, glue, wood preservative material, paint brush, hammer, auger, hand drill & bits, plumb-bob, spirit level, hose pipe, hammer and wood stock.

8 TASK PERFORMANCE STANDARDS

Required material and appropriate tools and equipment selected and/ or collected.

Dissembles, sharpens and resemble cutting tools. Previously marked wood stock, ply or teak cut square to size up to± 3mm.

Wood stock planed smoothly without off motion to the line and level, square and flat within +- 2mm in sectional size.

Previously marked joint housed without exceeding the mark line.

Work area cleaned.

- - 8

9 10

TASK TRAINING DATA

TASK NO

T.E NO

TECHNICAL KNOWLEDGE APPLIED CALCULATION

GRAPHIC INFORMATION

SAFETY & HYGIENE

1 2.1

Identification of common woods.

Knowledge of proper dress to avoid accidents

2.2

Identification of hard and soft wood .

Safe lifting techniques.

2.3

Distinction between good & defective wood stock.

Hazard involved during handling electric power hand tools.

2.4

Selection of wood stock according to instructions.

Able to read and take measurement with measuring tape.

Hazards involved in handling materials at wood selection site and their prevention.

3

Use and maintenance of required tools & equipments.

Hazards involved in handling sharp-edged tools.

4

Knowledge of squaring the wooden stock and marking & checking flatness, level & line.

First aid practice and reporting.

5

Knowledge of size and types of nails & screws.

Hazards involved in driving nails.

- - 9

TASK PERFORMANCE TEST ( SKILL ASSESSMENT)

11

TASK NO : 1 TASK TITLE : CONSTRUCTIONS CARPENTER L-1

LOCATION OF TEST: CANDIDATE' S NAME: EVALUATOR'S NAME:

12 TASK FACTORS AND ITEMS STANDARD MET STANDARD NOT MET (Comments) DID THE CANDIDATE ?

Select and/or collect required materials and appropriate tools and equipment

1.1

1.2 Cut wooden stock straight, square to the size up to +

3mm.

1.3 Plane the stock smoothly without off motion to the line and level, square and flat within +2mm in sectional size.

1.4 House previously marked joint without exceeding the mark line.

1.5 Use proper sizes and types of nails & screws.

1.6 Dress himself safely and clean the working area.

1.7 Observe related safety precautions.

- - 10


JOB TITLE : CONSTRUCTION CARPENTER L-1 INSTALLING DIFFERENT TYPES OF PREPARED WINDOW/ DOOR, PANELS, SHUTTERS. AND SLIDING

DOOR/WINDOW.

6 TASK ELEMENTS


2.2 Measures window/ door frame to determine length & breath of shutter/panels

2.3 Cuts or plane length & breadth of prepared shutters/panels.

2.4 Cleans rebate portion of the door or window frame.

2.5 Inserts/set prepared panels/shutters.

2.6 Cleans work area.

- - 11


Instructions/sketches, pencil, chalk line, measuring tape, try square, mitre square, saw, jack plane, block plane, rebate plane, hammer, oil stone, adze (bashila), plumb-bob, straight edge, sand-paper, portable power circular saw, carpenter's pincers, tack lifter, smoothing plane, mallet, screw driver, marking gauge and chisel.


2.1 Distance between the members of the frame measured to determine the length and breadth and marked accordingly to the frame, shutter & panels within + 2mm.

2.2 Required wooden frame cuts according to the door & window frame/shutter within + 2mm.

2.3 Rebate/groove portion cleaned and putty applied uniformly without excess putty.

2.4 Prepared panels, selected according to the size of frame, inserted without damaging and scratching panels which fit to the plumb and line.

2.5 Shutter/panel/sliding pannel installed firmly and tightly to the line and level without damaging gap.

2.6

Cleaned work area.

- - 12

9 10

TASK TRAINING DATA

TASK NO

T.E NO


GRAPHIC INFORMATION

SAFETY & HYGIENE

2 1 Identification of required materials.

.

2

Knowledge of taking measurements.

Able to read and take measurements with

measuring tape

Knowledge of proper dress to avoid accidents and first aid practice and reporting.

3 Knowledge of using & cleaning proper tools & equipments.

Hazards involved in tools & equipments.

4 Knowledge of handling, selecting and/or inserting prepared panels according to the size and requirement of the frames.

Hazards involved in handling panels/shutter & their prevention.

5 Knowledge of installing shutter/panels to the frame.

Hazards involved in fixing the shutter/ Panels.

- - 13


11

TASK NO : 2 TASK TITLE : INSTALLING DIFFERENT TYPES OF PREPARED WINDOW/ DOOR, PANELS, SHUTTERS. AND SLIDING DOOR/WINDOW


12 TASK FACTORS AND ITEMS STANDARD MET STANDARD NOT MET (Comments) DID THE CANDIDATE ?

Select and/or collect required materials and appropriate tools and equipments.

2.1

2.2 Measure distance between the members of the frame and mark accordingly to the shutter/panels within +_ 2mm.

2.3 Cut shutter/panels according to frame within +2mm.

2.4 Clean rebate/groove portion.

2.5 Select prepared glass panel/shutter according to frame size and insert it without breaking and scratching to fit frame to the plumb and line.

2.6 Install the panel firmly and tightly to the line and level without damaging the prepared panels/shutters without gap.

2.7 Dress himself safely and cleans work area.


- - 14


JOB TITLE : CONSTRCUTION CARPENTER L-1 CUTTING PLY-WOOD, TEAK PLY, METALIC SHEET, PLAIN WOODEN PANEL BOARD, OTHER BOARDS

AND WIRE MESH TO REQUIRED SIZES AND INSTALLING THEM IN THE FRAMES.

6 TASK ELEMENTS


3.2 Measures frames to determine the length and breadth to cut and/or prepare the materials.

3.3 Cuts/prepares material to required size.

3.4 Cleans rebate or groove portion if required.

3.5 Applies glue where required.

3.6 Inserts or installs ply-wood/teak ply/metallic sheet/plain wooden panel, different board and/or wire mesh to the frame.

3.7 Installs wooden and others beads as required.

- - 15


Instructions/sketch, pencil, chalk line, measuring tape, try square, saw, jack plane, rebate plane, smooth plane, bar-clamp, bench

vice, screw clamp, c-clamp, hammer, oil stone, adze (bashila), spirit level, hose pipe, plumb-bob, snipper, nail set, portable power hand tools, sandpaper , saw file, mallet and chisels, nails, wood stock, carpentor's pincers, marking gauge, metal scizer.

8 TASK PERFORMANCE STANDARDS 3.1 Frames measured to determine the size to prepare and/or cut stock straight/square to the size within +2mm.

3.2 Stock prepared and/or cut straight/square according to the taken measurement within + 2mm.

3.3 Rebate/groove portion cleaned if required.

3.4 Applied glue uniformly without excess where required.

3.5 Ply-wood/teak ply/metalic sheet/plain wooden panel different boards and/or wire mesh inserted and/or installed by nailing firmly

to secured stock or board by alternate, horizontal and vertical lines.

3.6 Wooden and other beads installed firmly by nailing to the line and level where required without damaging.

- - 16

9 10

TASK TRAINING DATA

TASK NO

T.E NO


GRAPHIC INFORMATION

SAFETY & HYGIENE

3 1 Identification of required materials.

2

Knowledge of taking measurements. Able to read and take measurements with measuring tape.

Knowledge of proper accidents.

3

Knowledge of required tools & equipments.


4

Knowledge of using & cleaning tools & equipment.

Hazards involved in handling tools & equipments.

5

Knowledge of applying glue uniformly. Hazards involved in handling cleaning tools & different materials.

6

Knowledge of inserting and installing cut ply-wood, teak ply/metallic sheet/ plain wooden panel board and/or wire mesh to the frame.

7 Knowledge of installing wooden and other beads to the frame.

- - 17


11

TASK NO : 3 TASK TITLE : Cutting ply-wood, teak ply, metalic sheet, plain wooden panel board other boards and wire mesh to required sized and installing them in the frames.


12 TEST FACTORS AND ITEMS STANDARD MET STANDARD NOT MET (Comments) DID THE CANDIDATE ?

Select and/or collect required materials and appropriate tools and equipments.

3.1

3.2 Measure frames to determine the size within + 2mm.

3.3 Prepare and/or cut stock straight/square according to

the measurement taken within + 2mm.

3.4 Clean rebate/groove portion well.

3.5 Apply glue uniformly where required.

3.6 Insert and/or install stock by nailing alternate horizontal and vertical lines, firmly to tighten and secure the stock to the frame.

3.7 Install wooden and otherbeads to the line and level firmly by nailing where required without damaging.

3.8 Observe related safety precaution.

3.9 Clean work area.

- - 18


JOB TITLE : CONSTRUCTION CARPENTER L-1 INSTALLING SIMPLE COMMON HARDWARE ACCESSORIES TO THE WOODEN FIXTURES.

6 TASK ELEMENTS


4.2 Selects/collects hardware accessories.

4.3 Chiseling and/ or sawing for hardware accessories.

4.4 Installs simple common hardware accessories to the wooden fixtures.

4.5 Checks fitness and adjusts if necessary.

- - 19


Instructions, pencil, carpenter's square, plumb-bob, screwdriver, gimlet, portable power hand drill, rasps and files, nails, wood stock and carpenter's pincers, nuts & bolts, screw, saw, pliers, hammer, sliding wrench.


4.1 Required simple/common hardware accessories selected/ collected as specified.

4.2 Sawing and chiseling performed for hardware accessory.

4.3 Simple common hardware accessories installed tight to the surface to the layout area.

4.4 Installed accessory must be easily workable with minimum friction.

- - 20

9 10

TASK TRAINING DATA

TASK NO

T.E NO


GRAPHIC INFORMATION

SAFETY & HYGIENE

4 1 Identification of required tools & equipments.

Knowledge of proper accidents.

2 Knowledge of selecting/collecting common hardware accessories as instructed.

3 Knowledge of marking system of hardware accessories.

Able to read and take measurements.

Knowledge of proper dress to avoid accidents.

4 Knowledge of installing simple common hardware accessories to the wooden fixtures.

do First aid practice and reporting.

5. Knowledge of checking the smooth workability of hardware accessories.

Hazards involved in handling tools & equipments and power tools..

6 Knowledge of applying glue uniformly where necessary.

Hazards involved in handling driving tools.

7 Knowledge of selection of proper nails and screws.

Hazards involved in handling spring hammer and claw hammer.

- - 21

TASK PERFORMANCE TEST ( SKILL ASSESSMENT) 11

TASK NO : 4 TASK TITLE : INSTALLING SIMPLE COMMON HARDWARE ACCESSORIES TO THE WOODEN FIXTURES.


12 TEST FACTORS AND ITEMS STANDARD MET STANDARD NOT MET (Comments)

4.1

DID THE CANDIDATE ? Select/collect required tools and materials.

4.2 Select specified simple common hardware accessory.

4.3 Mark in wooden fixture in-order to install simple common hardware accessory within mark line and dimension.

4.4 Install simple common hardware accessory tight to surface in wooden fixture to the layout area.

4.5 Install accessory which works easily with a minimum of friction.


4.7 Clean work area.

- - 22


JOB TITLE : CONSTRUCTION CARPENTER L-1 PREPARING WOODEN PEGS (POINTED POSTS) CORNERPOSTS, LEVELLING PEGS, POLING BOARDS,

WEDGES, STRUTS, VERICAL & HORIZONTAL WALLING SHEETING ( FOR LAYING TIMBERING IN FOUNDATION).

6 TASK ELEMENTS

5.1 Receive verbal instructions/sketches.

5.2 Selects required materials, rejects defective wood stock.

5.3 Measure's marks, cuts and pointing wood stock to required size.

5.4 Dresses the cut wood stock.

- - 23


Instructions/sketches, pencils, chalk line, measuring tape, try square saw, jack plane, bench vice, hammer, adze (bashila), plumb-bob, wood stock and portable power hand tools.


Required material selected/collect and/or procured as specified.

Wood stock cut square and point to size within ± 2mm.

Cut off wood stock dressed to the line and level and flat within 2mm in sectional size and within + 10mm in length.

- - 24

9 10

TASK TRAINING DATA

TASK NO

T.E NO


GRAPHIC INFORMATION

SAFETY & HYGIENE

5 2.1 Identification of common woods.

2.2 Identification of hard and soft woods and distinction between good and defective wood stock according to use.

Knowledge of proper dress to avoid accidents.

2.3 Selection of appropriate size of wood to result in minimum wastage.

First aid practice and reporting Safe lifting techniques, .

3.1 Knowledge of using tools & equipment and pointing.

3.2 Knowledge of marking, cutting according to required size and squre.

Able to measure the length, breadth with measuring tape.

Hazards involved in handling sharp edged materials at wood selection site and their prevention

4 Knowledge of dressing wood stock with adze (bashila) to the line and level, flat, and square.

do Hazards involved in handling tools & equipment power hand tools.

- - 25

TASK PERFORMANCE TEST ( SKILL ASSESSMENT) 11

TASK NO : 5 TASK TITLE : PREPARING WOODEN PEGS (POINTED POSTS) CORNERPOSTS, LEVELLING PEGS, POLING BOARDS, WEDGES, STRUTS, VERICAL & HORIZONTAL WALLING SHEETING ( FOR LAYING TIMBERING IN FOUNDATION).


12 TASK FACTORS AND ITEMS STANDARD MET STANDARD NOT MET (Comments)

5.1 DID THE CANDIDATE ? Select & collect required tools and materials.

5.2 Select/collect wood stock to give minimum wastage.

5.3 Cut wood stock square to size within +_ 2mm.

5.4 Dress cut off wood stock to the line and level flat and square within +_ 2mm in sectional size and within +_ 10mm in length.



- - 26


JOB TITLE : CONSTRUCTION CARPENTER L-1 PREPARING SURACES FOR PAINTING.

6 TASK ELEMENTS

6..1 Receive verbal instructions.

6.2 Cleans the surface with appropriate cleaning tools to remove foreign materials.

6.3 Punches the nail if necessary.

6.4 Applies putty, chalk powder and/or sawdust with glue to fill in holes and/or even up the surface.

6.5 Smoothes the surface with appropriate sandpaper/steel wool.

6.6 Wipes the surface with cotton cloth.

- - 27


Scraper, wire brush, rasp and file, jute, cotton cloth, water, sawdust, glue, sandpaper, chalk powder and portable sander, steel wool, spirit, putty, knife, mask, apron, stain.


Foreign materials removed from the surface to uniform smoothness with appropriate tools.

Surfaces washed to wet foreign materials to wipe them off easily.

Remaining wet foreign materials wiped from the surface with jute and/or cotton cloth.

Putty, chalk powder and/or sawdust with glue applied to the surface to filling holes and up surface.

Filling material scrap if necessary.

Surface smoothed to required smoothness with sand paper & steel wool.

- - 28

9 10

TASK TRAINING DATA

TASK NO

T.E NO


GRAPHIC INFORMATION

SAFETY & HYGIENE

6 2.1 Identification of common materials. Knowledge of proper dress to avoid accidents

2.2 Knowledge of appropriate cleaning tools and equipment.


4 Knowledge of using appropriate amount of clean water to wash the surface.

5 Knowledge of wiping with jute and/or cotton cloth.

6 Knowledge of applying putty, chalk powder , stain and/or sawdust with glue uniformly.

Knowledge of inflammable materials.

7 Knowledge of using and applying appropriate sandpaper/steel wool.

- - 29


11

TASK NO : 6 TASK TITLE : PREPARING SURACES FOR PAINTING.



6.1 DID THE CANDIDATE ? Select/collect appropriate tools & materials.

6.2 Remove foreign material from the surface and make the surface uniformly smooth.

6.3 Wash the surface to wet foreign materials enough to wipe them off easily.

6.4 Wipe remaining wet foreign materials from the surface with jute and/or cotton cloth.

6.5 Apply putty, stain and/or saw dust with glue to filling holes and even up surface.

6.6 Scrap filling material if necessary.

6.7 Smooth the surface to the required smoothness with appropriate sandpaper/steel wool.



- - 30


11

TASK NO : COMPREHENSIVE TEST TASK TITLE : PREPARING SURACES FOR PAINTING.



DID THE CANDIDATE ? Cut marked wood stock straight, square with appropriate saw to the size within + 2mm.

1

2 Plane the stock smooth without off motion to the line and level, square and flat within + 2mm in sectional size.

3 Dress/plane the marked wood stock to make specified size of rebate within + 2mm with appropriate tools.

4 Construct joints using appropriate tools at the marked portion in the wood members within given dimensions.

5. Install Hardware accessories in specified position.

6 Complete the given project within time allowed.

7 Observe related safety precaution.

8 Cleans work area.

uploads_downloads_construction carpenter, oss, l-1

Documents

national skill standard

skill test job title

wooden panel board

construction carpenter

sanothimi campus

job specification

job description

wood seasoning