user manual electrical compact universal slide … · user manual electrical compact universal...
TRANSCRIPT
USER MANUAL
ELECTRICAL COMPACT UNIVERSAL SLIDE
KUSE
Mechanical Part
BA-100058 Starting from serial number 422790 English, Edition 02/2008
User Manual Electrical Compact Universal Slide KUSE
1
Contents
1. Important information____________________________________________________________ 3 1.1. Introduction ______________________________________________________________________ 3 1.2. EU conformance (to EU Directive on Machines, Appendix II A) _________________________ 3 1.3. Product description and application _________________________________________________ 3 1.4. Dangers _________________________________________________________________________ 3 1.5. Additional information_____________________________________________________________ 4 1.6. Validity of the User Manual_________________________________________________________ 5
2. Technical data ___________________________________________________________________ 6 2.1. Technical data for KUSE-8__________________________________________________________ 6 2.2. Technical data for KUSE-10 ________________________________________________________ 7 2.3. Holding brake for vertical use ______________________________________________________ 8 2.4. Travel times ______________________________________________________________________ 9 2.4.1. KUSE-8 __________________________________________________________________________ 9 2.4.2. KUSE-10________________________________________________________________________ 10 2.5. Dimensions______________________________________________________________________ 11 2.5.1. Dimensions of KUSE-8____________________________________________________________ 11 2.6. Dimensions of KUSE-10___________________________________________________________ 12 2.7. Scope of delivery ________________________________________________________________ 13 2.8. Load calculations ________________________________________________________________ 13 2.8.1. Dynamic load in horizontal use ____________________________________________________ 13 2.8.2. Dynamic load in vertical use_______________________________________________________ 14 2.8.3. Static load ______________________________________________________________________ 14 2.9. Deformations____________________________________________________________________ 15
3. Positioning _____________________________________________________________________ 16 3.1. Installation position and assembly__________________________________________________ 16 3.2. Mounting the add-on units ________________________________________________________ 17 3.3. Installation of the holding brake ___________________________________________________ 18 3.4. Internal wiring and cable connections ______________________________________________ 19 3.4.1. Motor __________________________________________________________________________ 19 3.4.2. Encoder ________________________________________________________________________ 20 3.4.3. Inductive proximity switch ________________________________________________________ 20 3.4.4. Holding brake ___________________________________________________________________ 20
User Manual Electrical Compact Universal Slide KUSE
2
3.5. Controller wiring ________________________________________________________________ 20
4. Maintenance ___________________________________________________________________ 21 4.1. Positioning of ball cage___________________________________________________________ 21 4.2. Lubrication _____________________________________________________________________ 21 4.3. Replacing the motor _____________________________________________________________ 24 4.4. Toothed belt tension_____________________________________________________________ 25 4.5. Zero point adjustment ___________________________________________________________ 26
5. Parts lists for KUSE _____________________________________________________________ 28 5.1. Holding brake for vertical use (optional) ____________________________________________ 31
6. General information ____________________________________________________________ 32 6.1. Environmental compatibility and disposal___________________________________________ 32
User Manual Electrical Compact Universal Slide KUSE
3
1. Important information
1.1. Introduction
This User Manual describes the mechanical design, the technical data, the load limits, installation, maintenance and spare parts of the electrical compact universal slide KUSE.
1.2. EU conformance (to EU Directive on Machines, Appendix II A)
Rules and standards complied with: Machinery Directives 89/392/EEC, 91/368/EEC Manufacturer: Montech AG, Gewerbestrasse 12 CH–4552 Derendingen Tel. +41 32 681 55 00, Fax +41 32 682 19 77
1.3. Product description and application
The electrical compact universal slides KUSE are electrically operated, position-controlled linear units for executing regular, linear forward and backward movements in the horizontal direction. For movements in the vertical direction, a holding brake should be installed. The load limits which were specified by the technical data for each slide size must be complied with in all circumstances. Overloading can lead to faults and failure of the devices.
1.4. Dangers
The use of electrical compact universal slides KUSE in installations is permissible only when they are guarded by moveable, isolating protective devices according to EN 292-2 Section 4.2.2.3. Failure to comply with this safety measure can result in injuries due to crashing and impact, particularly in machines which start up automatically. It is essential to comply with the operating conditions and safety instructions described in the controller User Manual. It is essential to comply with the stated load limits.
� During operation, the surfaces of the motor and permanent magnet brake may reach up to100°C. The parts may be touched only when the temperature has fallen below 40°C (measurement of the surface temperature).
� During maintenance work on the KUSE, it must be ensured that the drive energy is switched off and cannot be switched on by unauthorized persons.
User Manual Electrical Compact Universal Slide KUSE
4
1.5. Additional information The aim of the present User Manual is to enable users to employ electrical compact universal slides KUSE correctly and safely. Should further information be required in relation to your particular application, please contact the manufacturer. When reordering User Manuals, it is essential to quote the reference number, the product name and serial number. This document can be obtained from our homepage www.montech.com. Nameplate Reference number Product name Serial number Montech AG Management
U. D. Wagner C. Wullschleger
User Manual Electrical Compact Universal Slide KUSE
5
1.6. Validity of the User Manual
Our products are continually updated to reflect the latest state of the art and practical experience. In line with product developments, our User Manuals are continually updated. Every User Manual has an order number (e.g. BA-100058) and an edition number (e.g. 02/2008). The order number and the addition number are shown on the title page. Validity Main device:
Full name Short name Reference number
Electrical compact universal slide KUSE KUSE-8-60 57829
KUSE-8-120 57830
KUSE-10-80 57831
KUSE-10-160 57832 Option:
Full name Short name Reference number
Holding brake (KUSE vertical) - 57063
User Manual Electrical Compact Universal Slide KUSE
6
2. Technical data
2.1. Technical data for KUSE-8
KUSE-8-60 KUSE-8-120
Stroke (max.) [mm] 60 120
Permitted mounted weight, horizontal mhmax [kg] 4 4
Permitted mounted weight, vertical mvmax 1) [kg] 3 3
Max. moment (static) M0xmax 2) [Nm] 24 30
Max. moment (static) M0ymax 2) [Nm] 18 27
Max. moment (static) M0zmax 2) [Nm] 18 27
Max. force (static) Fxmax 2) [N] 60 60
Max. force (static) Fymax 2) [N] 150 180
Max. force (static) Fzmax 2) [N] 150 180
Max. speed hor./vert. vmax [mm/s] 400 / 400 400 / 400
Max. acceleration hor./vert. accmax [mm/s2] 4500 / 4500 4500 / 4500
Weight [kg] 1.7 2.1
Drive Brushless electronic commutated DC motor,
toothed belt and ballscrew
Motor rated power [W] 60
Encoder system Encoder
Protective class IP42
Repeat precision 3) [mm] ± 0.01
Supply voltage/current 48VDC / 4A
Auxiliary voltage / current 24VDC / 1A
Reference point initiator Integrated inductive proximity switch
PNP
Noise pressure level [dBA] < 66
Temperature [°C] 10…50
Rel. humidity 5% - 85% (without condensation)
Ambient
Air purity Normal workshop atmosphere
Warranty period 2 years from the date of delivery
Installation position 1) Horizontal
Material Aluminum, steel, plastic 1) When used vertically, use permanent magnet brake (option).
2) See load calculations.
3) At constant motor temperature. Measured with max. load, max speed and load, max speed and load, max speed and 100 successive strokes.
User Manual Electrical Compact Universal Slide KUSE
7
2.2. Technical data for KUSE-10
KUSE-8-60 KUSE-8-120
Stroke (max.) [mm] 80 160
Permitted mounted weight, horizontal mhmax [kg] 6 6
Permitted mounted weight, vertical mvmax 1) [kg] 5 5
Max. moment (static) M0xmax 2) [Nm] 27 37
Max. moment (static) M0ymax 2) [Nm] 26 42
Max. moment (static) M0zmax 2) [Nm] 26 42
Max. force (static) Fxmax 2) [N] 90 90
Max. force (static) Fymax 2) [N] 210 270
Max. force (static) Fzmax 2) [N] 210 270
Max. speed hor./vert. vmax [mm/s] 380 / 350 380 / 350
Max. acceleration hor./vert. accmax [mm/s2] 4000 / 3500 4000 / 3500
Weight [kg] 2.6 3.3
Drive Brushless electronic commutated DC motor,
toothed belt and ballscrew
Motor rated power [W] 70
Encoder system Encoder
Protective class IP42
Repeat precision 3) [mm] ± 0.01
Supply voltage/current 48VDC / 4A
Auxiliary voltage / current 24VDC / 1A
Reference point initiator Integrated inductive proximity switch
PNP
Noise pressure level [dBA] < 66
Temperature [°C] 10…50
Rel. humidity 5% - 85% (without condensation)
Ambient
Air purity Normal workshop atmosphere
Warranty period 2 years from the date of delivery
Installation position 1) Horizontal
Material Aluminum, steel, plastic 1) When used vertically, use permanent magnet brake (option). 2) See load calculations. 3) At constant motor temperature. Measured with max. load, max speed and load, max speed and load, max speed
and 100 successive strokes.
User Manual Electrical Compact Universal Slide KUSE
8
2.3. Holding brake for vertical use
Holding brake for KUSE-8 and KUSE-10: With integrated permanent magnet brake 0.4 Nm, including housing and fixing screws.
Reference number 57063
Weight (without KUSE) [kg] 0.1
Type Permanent magnet unifical brake for dry run
Rated power [W] 6.2
Supply voltage 24VDC
Holding brake (KUSE vertical)
User Manual Electrical Compact Universal Slide KUSE
9
2.4. Travel times
2.4.1. KUSE-8 The travel times were determined under the following conditions: Symbol m s v ± a Unit kg µm mm/s mm/s² Position horizontal vertical - horizontal vertical horizontal vertical Value 4 3 variable 400 400 4500 4500 • Beginning the measurement with the “Start motion task” signal on the ECMR terminal X5-6 • End of the measurement with the “INPOS” signal (in position) an the ECMR terminal X7-3 • The travel time is measured between the signals “Start motion task” and “INPOS”. “In
Position“ window setting (ECMR software) = 200 µm horizontal / vertical
Symbol Unit Designation
m [kg] Weight of add-ons and/or load
t [ms] Travel time per travel distance s
s [mm] Travel distance or stroke
v [mm/s] Travel speed
±a [mm/s²] +a acceleration / -a delay
User Manual Electrical Compact Universal Slide KUSE
10
2.4.2. KUSE-10 The travel times were determined under the following conditions: Symbol m s v ± a Unit kg µm mm/s mm/s² Position horizontal vertical - horizontal vertical horizontal vertical Value 6 4 variable 380 350 4000 3500 • Beginning the measurement with the “Start motion task” signal on the ECMR terminal X5-6 • End of the measurement with the “INPOS” signal (in position) an the ECMR terminal X7-3 • The travel time is measured between the signals “Start motion task” and “INPOS”. “In
Position“ window setting (ECMR software) = 200 µm horizontal vertical
Symbol Unit Designation
m [kg] Weight of add-ons and/or load
t [ms] Travel time per travel distance s
s [mm] Travel distance or stroke
v [mm/s] Travel speed
±a [mm/s²] +a acceleration / -a delay
User Manual Electrical Compact Universal Slide KUSE
11
2.5. Dimensions
2.5.1. Dimensions of KUSE-8
A B C N STROKE
KUSE-8-60 222 172 127 2 0-60
KUSE-8-120 272 252 177 2 0-120
Ref. No. KUSE-8-60 57286 KUSE-8-120 57287
Cable length 3m
Stroke
Stroke
User Manual Electrical Compact Universal Slide KUSE
12
2.6. Dimensions of KUSE-10
A B C N Stroke
KUSE-10-80 251 201 147 2 0-80
KUSE-10-160 325 305 221 2 0-160
Ref. No. KUSE-10-80 57288 KUSE-10-160 57289
Cable length 3m
Stroke
Stroke
User Manual Electrical Compact Universal Slide KUSE
13
2.7. Scope of delivery
� Mechanical part including 3 m cable1) with loose ends for connecting to the ECMR controller. � 1) 3 m power cable: shielded and towable. � 1) 3 m data cable: unshielded and towable. � ECMR controller completely configured with all counter connection terminals for connecting
loose wires. � CD-ROM with Windows commissioning software and Operating Instructions in German, English,
French and Italian.
2.8. Load calculations
The load values specified in the technical data are maximum values for a single load. The following calculations apply to the combined loads encountered in practice: Definition of the loads
2.8.1. Dynamic load in horizontal use
( )( )YZ
ZXXY
YX
LmMLKLgmM
LgmM
⋅⋅⋅⋅=⋅⋅+⋅⋅⋅=
⋅⋅⋅=
a2001.0a2- 001.0
001.0
Combined dynamic load in horizontal use:
( ) 1≤maxmax ZX
ZX
Y
Y
MMMM
MM
B++
+=
User Manual Electrical Compact Universal Slide KUSE
14
2.8.2. Dynamic load in vertical use
( )( ) YZ
ZY
LagmMLgmM⋅⋅+⋅⋅=⋅⋅+⋅⋅=
2001.0a2001.0
Combined dynamic load in vertical use:
1≤maxmax Z
Z
Y
Y
MM
MM
B +=
2.8.3. Static load
( )
( )( )( )( )XXYYXZ
XXZZXY
YZZYX
KLFLFMKLFLFM
LFLFM
-001.0-001.0
001.0
0
0
0
⋅+⋅⋅=⋅+⋅⋅=⋅+⋅⋅=
Combined static load:
1≤max0
0
max0
0
max0
00
Z
Z
Y
Y
X
X
MM
MM
MM
B ++=
B, B0 Load factor: must not exceed the value l! Mi, M0i [Nm] Existing moments Mimax, M0imax [Nm] Max. permissible moments (see table) m [kg] Installation mass LX, LY, LZ [mm] Distance of moving mass from centre of gravity or force application distances FX, FY, FZ [N] Acting forces for max. values see “Technical Data” KX [mm] Constant according to table g [m/s2] Acceleration due to gravity (9.81 m/s2) a [m/s2] Acceleration
Horizontal use Vertical use Static
KX [mm]
MYmax [Nm]
(MX+MZ)max [Nm]
MYmax [Nm]
MZmax [Nm]
M0Xmax [Nm]
M0Ymax [Nm]
M0Zmax [Nm]
KUSE-8-60 42 12 15 12 12 24 18 18
KUSE-8-120 52 15 18 15 15 30 27 27
KUSE-10-80 47 17 20 15 15 27 26 26
KUSE-10-160 59 23 24 17 17 37 42 42
User Manual Electrical Compact Universal Slide KUSE
15
2.9. Deformations
Deformations KUSE-8
Deformations KUSE-10
User Manual Electrical Compact Universal Slide KUSE
16
3. Positioning
3.1. Installation position and assembly
Electrical compact universal slides KUSE can be installed in any position. As a rule, the housing (item 300) is fixed and the movement is executed by the slide (item 20). In vertical use, it is necessary to install a holding brake which secures the slide (item 20) when the control is switched off. The KUSE is assembled by means of Quick Set fixing elements (SLL-..-40) on the dovetail of the end plate (item 270) or via the threaded or positioning holes on the end plate (item 270). On assembly by means of Quick Set fixing elements, it is advisable to fix the end plate (item 270) with two clamping elements SLL-..-40 (utilization of the dovetail length, i.e. fixing as far as possible at the dovetail ends).
User Manual Electrical Compact Universal Slide KUSE
17
� With the use of Quick Set fixing elements, it is essential to ensure that the fixing elements do not project beyond the bearing flange at the front (item 220).
3.2. Mounting the add-on units Any add-on units can be fixed to the KUSE slide provided that the permissible loads are complied with. The add-on units are mounted by means of Quick Set fixing elements (SLL-..-40 or SLR-15-40) on the dovetails mounted on the slide (item 20) and on the end plate (item 270) or via the threaded and positioning holes on the slide (item 20) and end plate (item 270).
� When fixing add-on units, it is essential to comply with the static load limits of the KUSE slides with respect to the tightening torques.
User Manual Electrical Compact Universal Slide KUSE
18
3.3. Installation of the holding brake
� Loosen cheesehead screw(s) (item 500) and remove cover (item 350). � In KUSE-8, remove the spacer (item 540). � Loosen cheesehead screws (item 420) and remove adapter (item 300). � Clean contact surfaces on holding brake housing (item H/10) and motor flange (item 240). � Push holding brake onto peg (of the motor with toothed disk, item 250), position by means of
straight pins (item H/40) on the motor flange (item 240) and tighten with cheesehead screws (item H/50).
� Lead cable wires of the holding brake through the hole in the motor flange to the motor + sensor terminal group (item 330) and connect according to section “Internal wiring”.
� Energize holding brake (set digital input "Release brake“ [see Operating Instructions BA-100078 ECMR] or energize relevant cable leads as described in “Internal wiring”)
� Remove protective disk between flange hub (item H/20a) and magnet (item H/20b), adjust air gap width to 0.3 mm + 0/-0.05mm with thickness gage and fix flange hub (item H/20a) by tightening the two setscrews (item H/30).
� Fix adaptor (item 300) with cheesehead screws (item 420). �
The cables must be carefully laid and must not become jammed between the adapter (item 300) and the housing (item 10).
� � In KUSE-8, mount the spacer (item 540). � Mount the cover (item 350) again and tighten with cheesehead screw(s) (item 500).
User Manual Electrical Compact Universal Slide KUSE
19
Terminal strip c Terminal strip a 600 Terminal strip b
3.4. Internal wiring and cable connections
3.4.1. Motor
Inside device Output cable 3x0.5mm2
Designation Wire color Terminal Wire color Terminal
Motor winding 1 Red a 1 White b 1
Motor winding 2 Black a 2 Brown b 2
Motor winding 3 White a 3 Green b 3
Screen connection n.c. n.c. Screen Item 600
Inside device Output cable 18x0.14mm2
Designation Wire color Terminal Wire color Terminal
n.c. n.c. n.c. White n.c.
n.c. n.c. n.c. Brown n.c.
n.c. n.c. n.c. Green n.c.
Hall sensor 1 Yellow a 8 Yellow b 8
Hall sensor 2 Brown a 9 Grey b 9
Hall sensor 3 Grey a 10 Pink b 10
GND Hall sensors Blue a 0V Blue b 0V
U Hall sensors Green a + Red b +
Note: n.c.: Not connected.
User Manual Electrical Compact Universal Slide KUSE
20
3.4.2. Encoder
Inside device Output cable 18x0.14mm2
Designation Wire color Terminal Wire color Terminal
Vcc Encoder Grey-pink c 2
GND Encoder Red-blue c 3
A emer. White-green c 5
A Brown-green c 6
B emer. White-yellow c 7
B Yellow-brown c 8
I. emer. White-grey c 9
I
Flat cable
Multipoint
connector
(plug)
Grey-brown c 10
3.4.3. Inductive proximity switch
Inside device Output cable 18x0.14mm2
Designation Wire color Terminal Wire color Terminal
U ind. proximity switch Brown a + (Red)* (b +)*
GND ind. proximity switch Blue b 0V (Blue)** (b 0V)**
Output Black a 11 Black b 11
Note: *: U ind. proximity switch is connected internally to U Hall sensors. **: GND ind. proximity switch is connected internally to GND Hall sensors.
3.4.4. Holding brake
Inside device Output cable 18x0.14mm2
Designation Wire color Terminal Wire color Terminal
GND holding brake Blue a 0V (Blue)* (b 0V)*
U holding brake Red a 12 Violet b 12
Note: *: GND holding brake is connected internally to GND Hall sensors.
3.5. Controller wiring See chapter “Internal wiring and cable connections“ and Operating Instructions BA-100078 ECMR (EC motor controller), electrical and software part.
User Manual Electrical Compact Universal Slide KUSE
21
4. Maintenance
4.1. Positioning of ball cage When the KUSE has been operated for a long time without using the total nominal stroke, the ball cage (item 40) may migrate in the guidance direction, depending on load and initial stress distribution. If the stroke is subsequently increased, it is necessary to move at low speed (approx. reference speed) to both extreme positions before the start of the program cycle so that the ball cage (item 40) is repositioned.
4.2. Lubrication
� During maintenance work on the KUSE, it is necessary to ensure that the drive energy is switched off and cannot be switched on by unauthorized persons.
� With the use of a holding brake, the latter must be manually vented by means of a switch.
It is essential to use only Klüber oil “Paraliq P460” (Montech Ref. No. 504721). Lubrication interval: 800 operating hours
User Manual Electrical Compact Universal Slide KUSE
22
Lubrication of guide: Apply lubricant at 4 points “C” directly onto the guide track on the guide rails (item 30) and distribute by completely retracting and extending the slide several times (repeat process 2-3 times).
� Clean guide rails prior to lubrication.
C
C
C
C
User Manual Electrical Compact Universal Slide KUSE
23
Lubrication of ballscrew: � Extend slide (item 20) until the closure screw (item 90) is accessible. � Remove closure screw (item 90). � Apply lubricant through the opening in the housing (item 10) directly onto the ballscrew (item
100) and distribute by completely retracting and extending the slide several times (repeat process 2-3 times).
� Mount closure screw (item 90).
User Manual Electrical Compact Universal Slide KUSE
24
4.3. Replacing the motor
� Loosen cheesehead screw(s) (item 500) and remove cover (item 350). � In KUSE-8, remove the spacer (item 540). � Loosen cheesehead screws (item 420) and remove adapter (item 300). � Loosen cheesehead screws (item 470) and remove. � Tilt motor flange (item 240) with motor slightly toward ballscrew (item 100) and remove toothed
belt (item 260). � Pull out multipoint connector (item 250/30) with flat cable. � Detach cable wires from motor at motor + sensor terminal group (item 250/10) (also see section
“Internal wiring and cable connections”). � Loosen cheesehead screws (item 480) and remove. � Remove motor (item 250/10). � Position new motor (item 250/10) in motor flange (item 240) (note position of cable exits on
motor) and tighten cheesehead screws (item 480). � Loop cable wires from the motor below motor + sensor terminal group (item 250/10) and
connect to terminal strip (also see section “Internal wiring and cable connections”). � Insert multipoint connector (item 250/30) with flat cable into encoder terminal group (item 340). � Tilt motor flange (item 240) with motor slightly toward ballscrew (item 100) and push on toothed
belt (item 260). � Screw in cheesehead screws (item 470) and adjust toothed belt tension according to section
“Toothed belt tension”. � Fix adaptor (item 300) with cheesehead screws (item 420). �
� During operation the surfaces of the motor and holding brake can reach 100°C. Do not touch the parts until they have cooled to below 40°C (measure the surface temperature).
� The cables must be carefully laid and must not become jammed between the adaptor (item 300) and the housing (item 10).
� � Zero point adjustment according to section “Zero point adjustment”. � In KUSE-8, mount the spacer (item 540). � Mount cover (item 350) and fix with cheesehead screw(s) (item 500).
User Manual Electrical Compact Universal Slide KUSE
25
4.4. Toothed belt tension
� Loosen cheesehead screw(s) (item 500) and remove cover (item 350). � Slightly loosen cheesehead screws (item 470). � Pull motor flange (item 240) with motor away from toothed disk (item 250/20) so that the
toothed belt (item 260) has no initial tension.
� Tensioning the toothed belt (item 260) too strongly can lead to destruction of the motor bearing.
� Hold motor flange (item 240) and tighten cheesehead screws (item 470). � Mount cover (item 350) and fix with cheesehead screw(s) (item 500).
User Manual Electrical Compact Universal Slide KUSE
26
4.5. Zero point adjustment
� Keep hands and tools away during traversing. � Loosen cheesehead screw(s) (item 500) and remove cover (item 350). � Loosen hexagon nut (item 210) by approx. two turns while holding the hexagon socket of the
ballscrew (item 100). If the toothed disk (item 180) is not freely rotatable after the hexagon nut (item 210) has been loosened: Loosen adjusting nut (item 170) approx. one turn (toothed disk (item 180) will be pushed back as a result). Turn adjusting nut (item 170) back and tighten lightly. Push toothed disk (item 180) by hand against adjusting nut (item 170).
� Move slide (item 20) by hand to zero position (see figure) (proximity switch (item 560) is not
damped). � Start reference travel and damp proximity switch (item 560) by inserting a feeler gage and allow
to fall off again (motor travels to encoder index and remains standing under power).
User Manual Electrical Compact Universal Slide KUSE
27
� Place ground 9mm underlay between end plate (item 270) and front bearing block (item 220) and move slide (item 20) by hand until the underlay is clamped between end plate (item 270) and bearing block (item 220) at the front.
� Tighten hexagon nut (item 210) while holding hexagon socket of the ballscrew (item 100).
� Hold ballscrew (item 100) in position so that the motor does not act in the opposite direction.
� Start reference travel and check 9mm dimension (zero position). � Mount cover (item 350) and tighten with cheesehead screw(s) (item 500).
User Manual Electrical Compact Universal Slide KUSE
28
5. Parts lists for KUSE
Exploded view
User Manual Electrical Compact Universal Slide KUSE
29
Item Sym. Designation Ref. No. Mat.
KUSE-8-60
KUSE-8-120
KUSE-10-80
KUSE-10-160
◘ KUSE complete 57829 57830 57831 57832 Div.
10 ◊ Housing 57089 57157 57146 57140 Alu.
20 ◊ Slide 57090 57155 57144 57139 Alu.
30 ◊ Guide rail 56621 57154 57143 56622 Steel
40 ◊ Ball cage 56623 57156 57145 56624 Steel
50 ◊ Felt wick 51576 51576 51576 51576 Wool felt
60 ◊ Ball ø3 508414 508414 508414 508414 Steel
70 ◊ Stop 56636 56636 56637 56637 Alu.
80 ◊ Flat-head screw M3x5 503675 503675 503675 503675 Steel
90 ◊ Closure screw 57125 57125 57125 57125 Steel
100 ◊ Ballscrew 57094 57160 57148 57132 Div.
110 ◊ Support ring 57092 57092 57133 57133 Steel
120 ◊ Deep-groove ball bearing 505222 505222 508426 508426 Steel
130 ◊ Deep-groove ball bearing 520074 520074 520075 520075 Steel
140 ◊ Hexagon nut 56389 56389 56635 56635 Steel
150 ◊ Drive tube 56626 57161 57149 56627 Alu.
160 ◊ Bearing flange 56630 56630 56631 56631 Alu.
170 ◊ Adjusting nut 57093 57093 57136 57136 Steel
180 ◊ Toothed disk 56614 56614 56615 56615 Alu.
190 ◊ Spring collet 6x9 510010 510010 510010 510010 Steel
200 ◊ Centering sleeve 56634 56634 56634 56634 Steel
210 ◊ Hexagon nut M6x0.75 520042 520042 520042 520042 Steel
220 ◊ Bearing block, front 56619 56619 56620 56620 Alu.
230 ◊ Plug-in buffer 506160 506160 506160 506160 NR
240 ◊ Motor flange 57066 57066 57067 57067 Alu.
250 ● Motor with toothed disk 57299 57299 57302 57302 Div.
260 ● Toothed belt 520077 520077 520078 520078 PU
270 ◊ End plate 56618 56618 56625 56625 Alu.
280 ◊ End plate screw 56632 56632 56633 56633 Steel
290 ◊ Damper 57124 57124 57124 57124 Steel
300 ◊ Adapter 57091 57159 57147 57137 Alu.
310 ◊ Clamping piece 47906 47906 47906 47906 Steel
320 ◊ Clamping screw 47904 47904 47904 47904 Steel
330 ◊ Mo + Se terminal group 57281 57281 57281 57281 Div.
340 ◊ Encoder terminal group 57085 57085 57085 57085 Div.
350 ◊ Cover 57126 57126 57242 57242 ABS
User Manual Electrical Compact Universal Slide KUSE
30
Item Sym Designation Ref. No. Mat.
KUSE -8-60 -8-120 -10-80 -10-160
400 ◊ Chhd screw M3x18 Chhd screw M3x25
520073 -
520073 -
- 506707
- 506707
Steel
410 ◊ Chhd screw M3x8 Chhd screw M3x10
508470 -
508470 -
- 502503
- 502503
Steel
420 ◊ Chhd screw M3x10 Chhd screw M3x20
502503 -
502503 -
- 520107
- 520107
Steel
430 ◊ Chhd screw M4x14 508472 508472 508472 508472 Steel
440 ◊ Chhd screw M3x14 Chhd screw M4x14
520057 -
520057 -
- 508472
- 508472
Steel
450 ◊ Chhd screw M3x8 Chhd screw M3x10
508470 -
508470 -
- 502503
- 502503
Steel
460 ◊ Chhd screw M4 14 508472 508472 508472 508472 Steel
470 ◊ Chhd screw M4x10 508471 508471 508471 508471 Steel
480 ◊ Chhd screw M3x8 508470 508470 508470 508470 Steel
490 ◊ Chhd screw M3x10 502503 502503 502503 502503 Steel
500 ◊ Chhd screw M3x8 Chhd screw M4x60
508470 -
508470 -
- 520194
- 520194
Steel
510 ◊ Setscrew M4x4 Setscrew M4x6
502641 -
502641 -
- 506864
- 506864
Steel
520 ◊ Straight pin 502023 502023 502037 502037 Steel
530 ◊ Straight pin 502035 502035 502037 502037 Steel
540 ◊ Spacer 520193 520193 - - Steel
550 ◊ Cable screw union M12x1.5 520197 520197 520197 520197 Brass
560 ◘ Ind. proximity switch 508842 508842 508842 508842 Div.
570 ◊ Spacer sleeve 520184 520184 520184 520184 PA
580 ◊ Spacer sleeve 520258 520258 520258 520258 PA
590 ◊ Self-tap. chhd screw M3x10 520234 520234 520234 520234 Steel
600 ◊ Self-tap. chhd screw M3x16 520257 520257 520257 520257 Steel
610 ◊ Cable 520260 520260 520260 520260 Div.
620 ◊ Cable 520261 520261 520261 520261 Div.
630 ◊ Ribbed washer (M3) 505385 505385 505385 505385 Steel
640 ◊ Ribbed washer (M4) 502606 502606 502606 502606 Steel
650 ◊ Cable shoe fork M3 0.5-1 520345 520345 520345 520345 Div.
660 ◊ Cable screw union M12x1.5 520406 520406 520406 520406 Brass
900 ◊ Nameplate 41620 41620 41620 41620 Polyest
910 ◊ Nameplate cover 48508 48508 48508 48508 PU
● EC motor controller 57332 57332 57332 57332 Div.
● These are wearing parts and are available from stock, ◊ Not available from stock individually (upon request) , ◘ Price-listed items available from stock
User Manual Electrical Compact Universal Slide KUSE
31
5.1. Holding brake for vertical use (optional)
Exploded view
Item Sym. Designation Ref. No. Material
10 ◊ Holding brake housing 57123 Alu.
20 ◊ Permanent magnet brake 510017 Div.
30 ◊ Setscrew M3x4 505095 Steel
40 ◊ Straight pin 502011 Steel
50 ◊ Chhd screw M2x8 520192 Steel
60 ◊ Chhd screw M3x22 520058 Steel
70 ◊ Ribbed washer (M3) 505385 Steel
900 ◊ Nameplate 41620 Polyester
● These are wearing parts and are available from stock ◊ Not available from stock individually (upon request) ◘ Price-listed items available from stock
User Manual Electrical Compact Universal Slide KUSE
32
6. General information
6.1. Environmental compatibility and disposal Materials used: � Aluminum � Steel � Wool fibers � ABS (acrylonitrile/butadiene/styrene) � NR (natural rubber) � PU (polyurethane) � PA (polyamide) � Brass � Polyester Surface treatment: � Anodization of aluminum � Nickel-plating of steel � Coating of plastic
Shaping processes: � Extrusion of aluminum � Machining of aluminum and steel � Injection molding of plastics Emissions during operation: None Disposal: Electrical compact universal slides KUSE which cannot be used any more should not be recycled as complete units but should be dismantled into components and recycled according to type of material. The type of material used for each part is shown in the spare parts lists. Material which cannot be recycled should be appropriately disposed of.
MONTECH AG Gewerbestrasse 12, CH-4552 Derendingen Fon +41 32 681 55 00, Fax +41 32 682 19 77 [email protected], www.montech.com