using spectrum sweeps

10
Spooky2 Using Spectrum Sweeps Our Users & Team

Upload: spooky2-rife

Post on 12-Apr-2017

117 views

Category:

Health & Medicine


1 download

TRANSCRIPT

Page 1: Using Spectrum Sweeps

Spooky2 Using Spectrum Sweeps

Our Users & Team

Page 2: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

Have you been interested in trying the Spooky Spectrum Sweep or

Converge Sweep, but felt that it may be too difficult, and so you st

ayed away?The following shows how to setup a Spectrum Sweep

that targets 76000 Hz to 880000 Hz, attacking the pathogens from

both ends.

Page 3: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

First let's create the custom Spectrum Converge Sweep.

In Spooky2, go to the File menu, and select Create Spectrum

Sweep.

A new window will pop up that looks like the following. Fill it out

using the information shown in the image below and save.

After you have saved the information, go to the Database menu,

and click on Refresh Database.

Page 4: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

Page 5: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

Then, we will need to setup Spooky2 to run the newly created Spo

oky HC Converge Sweep.

Use the image below to setup the program options. Once you are

done, you can save this as a preset by giving it a name in the Prog

ram Preset field and clicking the large + to the right. This will make

it easy to recall the program for future use.

To be able to edit and set the Out 2 Controls, you must select Follo

w Out 1 first.

Page 6: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

Of note, the repeat program setting in the following screen shot

is set to 0. When you go to run this, you may want to choose h

ow many repetitions to use. The entire sweep takes 3,333 seco

nds to complete (interesting number synchronicity) or 55 minut

es, 33 seconds. At a minimum I would suggest running for at le

ast a full day.

Page 7: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

If you do not have a Spooky Boost, you can plug two Spooky Rem

otes into each output of the generator.

If you do not have two Spooky Remotes, you can still run this with

a single Spooky Remote installed on output 1, you will just loose th

e benefit of the reverse sweep.

Page 8: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

Page 9: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

It is important to note that due to the power requirements of a Spe

ctrum Sweep, this is currently only viable via remote or plasma ap

plications. If plasma is used, select Square waves, 5 volts Amplitu

de and 0% offset.

Page 10: Using Spectrum Sweeps

Official Support Website: www.spooky2.comOfficial Purchasing Website: www.spooky2-mall.com

Email:[email protected] [email protected]

Thank you!