using the avid mojo dnaresources.avid.com/supportfiles/attach/using_mojodna_0573601a.pdf · a using...

aUsing the Avid Mojo DNA

Important Information

Avid® recommends that you read all the information in these installation instructions thoroughly before connecting or using your new hardware.

This document explains how to use and connect cables and devices to the Avid Mojo™ Digital Nonlinear Accelerator (DNA) and how to connect specific devices to an Avid-supported PC or Macintosh® system that the Avid Mojo is connected to. The supported PC and Macintosh systems used with your Avid Mojo can change at any time.

n Please look at the ReadMe file that installs with the application. It contains important information that is used in conjunction with the information presented in this document.

Contents

If You Need Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Symbols and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Avid Mojo DNA Front and Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Avid Mojo DNA Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Avid Mojo DNA Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Synchronizing Audio and Video Equipment. . . . . . . . . . . . . . . . . . . . 9

Using the Avid Mojo DNA

2

Power-On Self-Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Peripheral Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting Audio Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting S-Video or DV Signals. . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting a Client Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting a Video Deck — Component Signal . . . . . . . . . . . . . . . 13

Controlling a Video Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Supported Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

FireWire Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Internal IDE Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Formatting and Striping MediaDrives (Windows) . . . . . . . . . . . . . . . 17

Formatting and Striping MediaDrives (Macintosh) . . . . . . . . . . . . . . 18

Using Striped Drives on Mac OS X and Mac OS 9.x Systems . 19

Moving Striped Drives to Another System (Macintosh Only) . . . 19

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Regulatory and Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

FCC Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Canadian ICES-003 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

European Union Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Australia and New Zealand EMC Regulations . . . . . . . . . . . . . . . . . 26

Technical Support Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

If You Need Help

3

If You Need Help

If you are having trouble using Avid Mojo DNA:

1. Retry the action, carefully following the instructions given for that task. It is especially important to check each step of your workflow.

2. Check these installation instructions for the latest information that might have become available after the documentation was published.

3. Check the documentation that came with your Avid application or your hardware for maintenance- or hardware-related issues.

4. Visit the online Knowledge Center at www.avid.com/support. Online services are available 24 hours per day, 7 days per week. Search this online Knowledge Center to find answers, to view error messages, to access troubleshooting tips, to download updates, and to read or join online message-board discussions.

5. For Technical Support, please call 800-800-AVID (800-800-2843).

For Broadcast On-Air Sites and Call Letter Stations, call800-NEWSDNG (800-639-7364).

Symbols and Conventions

These installation instructions use the following symbols and conventions:

Symbol or Convention Meaning or Action

n A note provides important related information, reminders, recommendations, and strong suggestions.

c A caution means that a specific action you take could cause harm to your computer or cause you to lose data.

w A warning describes an action that could cause you physical harm. Follow the guidelines in this document or on the unit itself when handling electrical equipment.

http://www.avid.com/support


4

Overview

The Avid Mojo DNA is designed to capture and output analog media and digital media (DV 25) using digital decks and cameras.

The Avid Mojo DNA is powered by an autosensing power adapter that plugs into a wall plug or power strip.

The Avid Mojo DNA accepts video and audio in different formats and resolutions, and changes these formats and resolutions to Avid-specific data for transfer to the Avid editing system over a 1394 cable. The data transfer uses an Avid-specific protocol that describes the format and resolution of the data being input.

You then edit the data on the Avid editing system and return it to the Avid Mojo DNA to be changed back to the proper format and resolution as needed for video and audio output.

n To capture and play 1:1 video, you must have an Avid Mojo connected to your system. Disconnecting the Avid Mojo results in a “Wrong Format” error message for those 1:1 clips. However, without an Avid Mojo attached, you can transcode your 1:1 video clips to DV 25 or 15:1s. For more information, see “Using the Transcode Option” in the Help.

The Avid Mojo DNA consists of:

• The Avid Mojo DNA

• A stand

• A power adapter with power cord

Also included in the kit is a 6-pin to 6-pin 1394 cable that connects the Avid Mojo to the host system platform and a Using the Avid Mojo DNA CD-ROM.

You can also order a special adapter cable that allows you to send a component signal into or out of the Avid Mojo using both the S-Video and composite connectors at the rear of the Avid Mojo.

Avid Mojo DNA Front and Rear Panel

5


You can place the Avid Mojo DNA in a stand or position it on its side. The Avid Mojo turns on when you connect the power adapter. You attach cables to connect the power, the system, and external devices at the rear.

Figure 1 Avid Mojo DNA in the Stand

Rear

Stand

Front panel


6

Avid Mojo DNA Front Panel

The Avid Mojo DNA front panel contains function LEDs behind a cover, a headphone jack, and volume control for the headphones (see Figure 2).

n The function LEDs are not labeled on the front panel. You can see the function names through the cover when it is lit.

Figure 2 Avid Mojo DNA Front Panel

Table 1 shows the name of each LED and describes its function.

CLIP 48KHZ DV REF HOST POWER

Headphone jack Volume controlLEDs

Table 1 LED Functions

LED Function

Clip Flashes red as audio data is lost (due to overloading or peaking), and for power-on self-test. See “Power-On Self-Tests” on page 9.

48KHz Lit when 48-KHz audio is selected; not lit when 44 KHz or 32 KHz is selected.

DV Lit when DV input is selected in the application.

Ref Lit when the Avid Mojo DNA is synced to the HOST and a project is selected.

Host Lit when the Avid Mojo DNA is connected to the HOST.

Power Lit when the power adapter is connected to the Avid Mojo DNA.


7

Avid Mojo DNA Rear Panel

Figure 3 shows the connections on the rear of the Avid Mojo DNA, while Table 2 describes the function of each connector. The rear connectors are labeled on the device.

Figure 3 Avid Mojo DNA Rear Panel (SD video and Audio Boards)

Although not labeled as a Component connection, you can connect a custom cable to the S-Video and Composite input connectors that allows you to input a Component signal into the Avid Mojo DNA. The same cable can be used to output a Component signal when connected to the S-Video and Composite output connectors. Connectors are described in Table 2.

HostDV

Ref Video

Audio Audio Video DC

INInput Output

Host

DV

Ref input S-Video input

Composite video input (yellow)

Audio output(left, white)

Audio output(right, red)

Composite video output (yellow)

S-Video output

DC InAudio input(left, white)

Audio input(right, red)

Table 2 Avid Mojo DNA Rear Connectors

Label Function

Host A 6-pin 1394 connector used to input and output audio and video signals to and from the Avid editing system

DV A 4-pin 1394 connector used for input and output to and from a DV camera or deck and the Avid Mojo DNA

REF Input An RCA connector that provides a connection of a black burst or house sync input; synchronizes decks that are part of the system


8

Video Input A 4-pin S-Video connector and an RCA connector that allow you to input video signals to the system

S-Video and Composite video connectors are used to connect the analog video outputs of a video camera or deck.

Component Input An optional cable (purchased separately) that uses the S-Video and the Composite video input connectors, allowing you to input a Component signal; connects to the analog video output of a deck

Audio Input Two RCA connectors used for the left and right Audio input signals; connect to an analog audio output of a video camera or deck

Audio Output Two RCA connectors used for the left and right Audio output signals; connect to an analog audio input of a video camera or deck

Video Output A 4-pin S-Video connector and an RCA connector that allow you to output video signals to a video camera or deck

S-Video and Composite video connectors are used to connect the analog video inputs of a video camera or deck.

Component Output

An optional cable (purchased separately) that uses the S-Video and the Composite video output connectors, allowing you to output a Component signal; connects to analog video input of a video deck or monitor

Power Connects to the power adapter

Table 2 Avid Mojo DNA Rear Connectors (Continued)

Label Function

Power-On Self-Tests

9

Synchronizing Audio and Video Equipment

Avid systems require synchronization when inputting audio and video. A synchronization signal for analog audio and analog video is generated internally by the Avid Mojo DNA from one of the following three sources:

• Internal — The signal is generated by the Avid Mojo DNA internally. This signal cannot be sent outside of the Avid Mojo DNA.

• Incoming video signal — The sync signal is generated from the incoming video: component, composite, or S-Video.

• Video Reference IN (Ref) — The sync signal should be used when you are capturing analog audio only. It should be generated from the incoming signal (black burst generator [BBGen] or house sync). If there is no sync connected to REF, the internal sync is used by default to sync the incoming audio.

n By default, the sync signal is generated from incoming video whenever you capture analog video. Depending on the configuration of the audio and video equipment attached to the Avid Mojo DNA, you might need to use a black burst generator or house sync; for example, when you perform an Insert Edit.

Power-On Self-Tests

The Avid Mojo DNA runs power-on self-tests (POSTs) to determine if the box and the board within the box are operating properly each time you turn it on.

If a failure occurs when running a POST, the Clip LED (see Figure 2) blinks steadily once a second. Also, if the Power LED does not light after you connect the Avid Mojo DNA to the power adapter, the Avid Mojo DNA is not capable of running diagnostics and is not functioning properly. If possible, try another power adapter. If the Avid Mojo DNA does not work with a different power adapter, replace the Avid Mojo DNA.


10

Connecting Peripheral Equipment

There are several possible cabling configurations depending on your camera, video deck, and client monitor. The audio and video output signals are available to each output connector at the same time. Video and audio cables are not included with the Avid Mojo DNA. Avid provides optional video cables that use the S-Video and Composite video connectors for a component connection to your deck. The following sections describe several possible connections:

• Connecting Audio Signals

• Connecting S-Video or DV Signals

• Connecting a Client Monitor

• Connecting a Video Deck — Component Signal

• Controlling a Video Deck

Connecting Audio Signals

Audio input and output connections on the rear of the Avid Mojo DNA use standard RCA connectors. Audio connections require the following:

• Four audio cables with RCA connectors on both ends of the cable. You can also use audio cables with RCA connectors on one end and XLR connectors on the other end.

• A video deck or audio device with audio input and output connections.


11

To connect your audio to a deck or audio device:

1. Attach two audio cables to the Audio input connectors (see Figure 4):

n Your cables might be color-coded with red and white connectors. If so, match the colors on the RCA connectors with the color of the inputs on the Avid Mojo DNA.

n If you have RCA-to-XLR connectors on your audio cables, you must pay attention to the male and female XLR connections attached to your audio device.

a. Connect an RCA connector to the red Audio input connector on the Avid Mojo DNA.

b. Connect an RCA connector to the white Audio input connector on the Avid Mojo DNA.

2. Attach the other end of the audio cables (or XLR connectors) to Audio output connectors on your deck or audio device.

Figure 4 Connecting Audio to the Deck

HOSTDV

Ref In Video In

Audio In Audio Out Video Out Power

Audio input (white) Audio output (red)

To Audio input on the deck or audio device

Audio input (red) Audio output (white)

To Audio output on the deck or audio device

RCA jack to RCA jack cable

XLR connector to RCA jack cable


12

3. Attach two more audio cables to the Audio output connectors (see Figure 4):

a. Connect an RCA connector to the red Audio output connector on the Avid Mojo DNA.

b. Connect an RCA connector to the white Audio output connector on the Avid Mojo DNA.

4. Attach the other end of the last two audio cables (or XLR connectors) to Audio input connectors on your deck or audio device.

Connecting S-Video or DV Signals

The S-Video and DV connectors on the rear of the Avid Mojo DNA use industry-standard connectors. The connections are as follows:

• There are two S-Video connectors on the rear of the Avid Mojo DNA. One connector is for video input, and the other is for video output. Figure 5 identifies the connectors.

• The DV connector uses a 4-pin 1394 cable that carries the video and audio input and output signals to and from your DV device. You can also use a 4-pin to 6-pin DV cable if your DV device uses a 6-pin connector. Figure 5 identifies the connector.

Figure 5 Connecting S-Video or DV to the Deck

HostDV

Ref Video


INInput Output

4-pin DV S-Video input S-Video output


13

Connecting a Client Monitor

To view the video as it passes through the Avid Mojo DNA, you might want to connect a monitor. You have two options:

• Most video decks provide a video output connector. You can connect a monitor to the deck to see the video sent to the Avid Mojo DNA or the video the Avid Mojo DNA sends to the deck. See your video deck manufacturer’s documentation for more information.

c The video you see in the monitor connected to the deck might not indicate there is a video signal going to the Avid Mojo DNA.

• You can see the input and output video signals passing through the Avid Mojo DNA using the Composite video output connector on the rear of the unit. Connect a composite monitor to the connector identified in Figure 6.

Figure 6 Connecting a Composite Monitor

Connecting a Video Deck — Component Signal

An optional component video deck connection requires the following:

• Two Avid Mojo DNA component video cables

• A video deck with component inputs and outputs

HostDV

Ref Video


INInput Output

Composite video output


14

To connect a deck using component signals:

1. Locate a component video cable (see Figure 7).

There are three BNC connectors on one end of the cable; the other end has an RCA connector and an S-Video connector.

Figure 7 Optional Component Cable

2. Attach the RCA and S-Video end of the cable to the Avid Mojo DNA inputs as follows (see Figure 8):

a. Connect the RCA connector to the yellow Composite video input connector on the Avid Mojo DNA.

b. Connect the S-Video connector to the S-Video input connector on the Avid Mojo DNA.

Figure 8 Connecting a Video Deck — Component Signal

S-Video connector

Three component BNC connectors for the deck connection

Composite video RCA connector

HostDV

Ref Video Audio Audio VideoDCIn

Input Output

S-Video input S-Video output

To component in on the deck

Composite video input Composite video output

To component out on the deck


15

3. Attach the other end of the component cable (with the three BNC connectors) to Component output of your video deck as follows:

a. Connect the BNC attached to the green wire to the component output connector labeled Y.

b. Connect the BNC attached to the red wire to the component output connector labeled R-Y.

c. Connect the BNC attached to the blue wire to the component output connector labeled B-Y.

4. Locate another component cable and attach the RCA and S-Video end to the Avid Mojo DNA outputs as follows (see Figure 8):

a. Connect the RCA connector to the yellow Composite video output connector on the Avid Mojo DNA.

b. Connect the S-Video connector to the S-Video output connector on the Avid Mojo DNA.

5. Attach the other end of the component cable (with the three BNC connectors) to Component input of your video deck as follows:

a. Connect the BNC attached to the green wire to the component input connector labeled Y.

b. Connect the BNC attached to the red wire to the component input connector labeled R-Y.

c. Connect the BNC attached to the blue wire to the component input connector labeled B-Y.

n Make sure you terminate the input signal if your video deck supports passthrough. See the documentation that is provided with your video deck.

Controlling a Video Deck

Avid editing systems provide video deck control through a serial control connector on most decks. You can control a single deck by using an RS-232 to RS-422 serial adapter. An optional RS-232 to RS-422 serial adapter kit is available through Avid.


16

The optional serial adapter kit that contains the following:

• An RS-232 to RS-422 serial adapter

• Two serial cables; with 9-pin male connectors at both ends

To connect a single deck to your system:

1. Locate the serial adapter kit.

2. Attach one end of a 9-pin cable to the end of the serial adapter labeled RS-232.

3. Attach the other end of the 9-pin cable to the serial port on the Avid editing system (see Figure 9) or to the serial connector of the USB-to-serial adapter.

n When you attach the cable to the serial port on the PC, note if you are using the COM1 or COM2 serial port. You need to select the port in the Avid editing application.

Figure 9 Video Deck Control Cabling

4. Attach one end of another 9-pin cable to the end of the serial adapter labeled RS-422.

5. Attach the other end of the 9-pin cable to the remote serial port of the video deck.

n Place the deck in Remote mode before attempting to control the deck using the software. See the documentation provided with your deck.

To video deck

RS-422 connection RS-232 connection

To Avid editing system

Serial Adapter

Supported Storage

17

Supported Storage

Storage options are explained in the following sections.

FireWire Drives

When you are using an Avid Mojo DNA and you want to use FireWire® drives, you need a second 1394 OHCI board on a different bus segment in your Avid editing system. See your computer manufacturer’s documentation to identify a PCI bus slot that is on a different bus segment than the 1394 port used for the Avid Mojo DNA.

Internal IDE Drives

An internal IDE drive can be used for media storage with your Avid Mojo DNA.

Formatting and Striping MediaDrives (Windows)

To use all the resolutions available in your Avid editing application, you might need to stripe your MediaDrives. Disk drives must be configured as Dynamic if you are striping drives.

To configure and stripe a drive:

1. Start your system, and log in to an account with administrative privileges.

2. Right-click the My Computer icon, and select Manage.

The Computer Management window opens.

3. Click the Disk Management folder.

n For more information on the Computer Management window, click the Help icon in the toolbar of the Computer Management window.


18

4. Make a Dynamic drive by right-clicking the disk ID section of the disk in the Computer Management window and selecting Upgrade to Dynamic disk, or Create Dynamic disk, depending upon the status of your disk.

When you select a disk in the Computer Management window, the white section of the disk changes to stripes, showing that the section has been selected.

5. Repeat step 4 for each drive you want to stripe.

6. Right-click one of the Dynamic drives and select Action > Create Volume.

7. Follow the instructions in the Create Volume Wizard to finish striping the drives using NTFS format.

Formatting and Striping MediaDrives (Macintosh)

To use all the resolutions available in your Avid editing system, use the ATTO ExpressStripe software to stripe drives on the Mac OS® X operating system. The ExpressStripe software is installed in the following location:

/Applications/ExpressStripe

The instructions for using the software are in a PDF file, Expressstripe.pdf, that is installed along with the ExpressStripe application.

n You must be logged in as an Administrator to stripe drives.

c Do not use the Apple Disk Utility application (in Applications/Utilities) to stripe drives. If you use the Disk Utility application, you will not be able to view the drives on the Mac OS 9 system. Additionally, Avid’s drive filtering feature will not function properly, resulting in poor performance.

Supported Storage

19

Using Striped Drives on Mac OS X and Mac OS 9.x Systems

The Avid editing software automatically recognizes drives that were striped on Mac OS 9.x. You should be able to use these drives to edit and play video. However, if you move a drive that was striped on a Mac OS X system back to Mac OS 9.x, you cannot play video from the drives on Mac OS 9.x. If necessary, you can set up your Mac OS 9.x system so that it recognizes the drives. You can then copy media files from the drive to your Mac OS 9.x drives.

To set up a Mac OS 9.x system to recognize drives that were striped on a Mac OS X system:

1. Navigate to the following folder:

Applications/Avid Goodies/OS 9/System Folder/Extensions

2. Copy the file ~~ExpressStripe_OS9_Enablr to the Extensions folder on your Mac OS 9 system.

3. Restart the Mac OS 9 system.

The system is now able to recognize the striped drives. You can use the drives to copy media onto your Mac OS 9 drives.

c Do not run a Mac OS 9 Avid editing application on the same system as a Mac OS X Avid editing system. There might be conflicts between the system files used by the two applications.

Moving Striped Drives to Another System (Macintosh Only)

In order to move striped drives to another system, you need to be able to identify the drives that make up a particular striped set. This was easy on Mac OS 9 because the system allowed you to use the SCSI ID order when striping drives.

On Mac OS X, the system does not use the SCSI ID but instead uses its internal diskn name (where n is the drive number) when creating the striped sets. You can use Avid Storage Manager or ExpressStripe to identify a striped set on Mac OS X.


20

To use Avid Storage Manager to identify a striped set:

1. Start the Avid Storage Manager application and select View > Volumes.

2. Select the striped volume you wish to move and click Identify.

The system blinks the lights on the front of the drives that make up the volume.

To use ExpressStripe to identify a striped set:

1. Start the ExpressStripe application.

2. In the opening dialog boxes, select Utilities and then select Benchmark.

3. Select the striped volume you want to move and click Start.

The system runs the benchmark test on the volume and shows activity on the front of the drives that make up the volume.

Specifications

The following sections provide specifications for the Avid Mojo DNA.

Dimensions and Weight

Table 3 shows the dimensions and weight for the Avid Mojo DNA enclosure. The dimensions are based on the unit in the stand; the orientation is shown in Figure 1 on page 5.

Table 3 Dimensions and Weight

Dimension Avid Mojo DNA Stand

Width 1.13 in (28.7 mm) 4.5 in (114.3 mm)

Height 11.0 in (279.4 mm) 2.13 in (54.1 mm)

Depth 6.8 in (172.7 mm) 8.5 in (215.9 mm)

Weight 1.5 lb (0.68 kg) 1.32 lb (0.59 kg)

Specifications

21

Environmental Specifications

Table 4 shows the environmental specifications for the Avid Mojo DNA enclosure.

Electrical Specifications

Table 5 shows electrical specifications for the power adapter used to power the Avid Mojo DNA enclosure.

Table 4 Environmental Specifications

Environment Specification

Ambient room temperature (Maximum) 95°F (35°C)

Operating humidity 5% to 90% noncondensing

Storage temperature –40°F to 158°F (–40°C to 70°C)

Storage humidity 5% to 95% noncondensing

Table 5 Electrical Specifications for Power Adapter

Topic Specification

Voltage

Input range

Output

90 V ac to 264 V ac

9 V dc

Frequency range 47 Hz to 63 Hz

Current

ac input

dc output

0.7 a for 115 V ac0.4 a for 230 V ac

2.23 a

Watts 20 w


22

Regulatory and Safety Notices

The following sections explain the regulatory and safety notices for the Avid Mojo DNA.

Warnings and Cautions

w Never install equipment if it appears damaged.

w Disconnect the power cord before servicing unit.

w Only perform the services explicitly described in this document. For services or procedures not outlined in this document, speak with authorized Avid service personnel.

c Follow all warnings and cautions in the procedures.

c Operate the device within its marked electrical ratings and product usage instructions.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.


23

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canadian ICES-003

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

European Union Notice

Declaration of Conformity (According to ISO/IEC Guide 22 and EN 45014)

Application of Council Directives:

73/23/EEC, 89/336/EEC.

Standards to which Conformity is Declared:

EN60950:2000 Third EditionCISPR 22:1997 / EN55022:1994 + A1:1995 + A2:1997 Class B EN55024:1998/EN61000 — 3-2, 4-2, 4-3, 4-4, 4-5, 4-6, 4-8, 4-11, 3-3

Manufacturer’s Name:

Avid Technology, Inc. 1925 Andover StreetTewksbury, MA 01876, USA


24

European Contact: Nearest Avid Sales and Service Office or Avid Technology International B.V. Sandyford Business Center Unit 3,Dublin 18, Ireland

Type of Equipment: Information Technology Equipment

Product Name: Products for the Windows NT, Windows 2000, or Windows XP Operating System: Avid Adrenaline DNA, Avid DS Nitris DNA, Avid Equinox Break-Out-Box, Avid|DS, Avid Mojo DNA, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, NewsCutter, NewsCutter DV, NewsCutter XP, Symphony

Products for the Mac OS X Operating System: Avid Adrenaline DNA, Avid Mojo DNA, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, Symphony

Products for the UNIX Operating System: AirPlay, VideoSPACE

Products for MediaNetwork and Workgroups: Avid ProEncode, Avid Unity MediaManager, Avid Unity MediaNetwork, Avid Unity TransferManager, LANserver, LANserver EX, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Nearchive, PortServer, Xdeck


25

(1) Products for the Windows NT, Windows 2000, or Windows XP Operating System: products were tested in a typical Avid Adrenaline DNA, Avid DS Nitris DNA, Avid Equinox Break-Out-Box, Avid|DS, Avid Mojo DNA, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, NewsCutter, NewsCutter DV, NewsCutter XP, or Symphony configuration.

(2) Products for the Mac OS X Operating System: products were tested in a typical Avid Adrenaline DNA, Avid Xpress, Avid Xpress DV, Film Composer, Media Composer, MediaDock 2+, MediaDock LVD, MediaDrive, MediaRAID, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Meridien I/O box, or Symphony configuration.

(3) Products for the UNIX Operating System: products were tested in an AirPlay or VideoSPACE configuration.

(4) Products for MediaNetwork and Workgroups: products were tested in a typical Avid ProEncode, Avid Unity MediaManager, Avid Unity MediaNetwork, Avid Unity TransferManager, LANserver, LANserver EX, MEDIArray, MEDIArray Drive, MEDIArray II, MEDIArray II Drive, Nearchive, PortServer, or Xdeck configuration.

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directives and Standards.

George R. Smith, Director of Hardware Engineering

Base Model Numbers:

None

Product Options: All

Year of Manufacture: 2003


26

Australia and New Zealand EMC Regulations

John Kells, Australian Operations ManagerAvid Technology (Australia)Unit B5 Skyline PlaceFrench Forest NSW 2086AustraliaPhone: 61-2-8977-4800

Technical Support Information

Most products feature a number of coverage options. Avid Assurance service offerings are designed to facilitate your use of Avid solutions. Service options include extended telephone coverage, automatic software maintenance, extended hardware warranty, and preferred pricing on replacement parts.

For more information regarding Avid’s service offerings, visit www.avid.com/support or call Avid Sales at 800-949-AVID (800-949-2843).

Program availability and details might vary depending on geographic location and are subject to change without notice. Contact your local Avid office or your local Avid Reseller for complete program information and pricing. However, if you need help locating an Avid office or Avid Reseller near you, please visit www.avid.com or call in North America 800-949-AVID (800-949-2843). International users call 978-275-2480.

N1709

Technical Support Information

27

Copyright and DisclaimerProduct specifications are subject to change without notice and do not represent a commitment on the part of Avid Technology, Inc.

The software described in this document is furnished under a license agreement. You can obtain a copy of that license by visiting Avid's Web site at www.avid.com. The terms of that license are also available in the product in the same directory as the software. The software may not be reverse assembled and may be used or copied only in accordance with the terms of the license agreement. It is against the law to copy the software on any medium except as specifically allowed in the license agreement.

Avid products or portions thereof are protected by one or more of the following United States patents: 4,746,994; 4,970,663; 5,045,940; 5,267,351; 5,309,528; 5,355,450; 5,396,594; 5,440,348; 5,452,378; 5,467,288; 5,513,375; 5,528,310; 5,557,423; 5,568,275; 5,577,190; 5,584,006; 5,640,601; 5,644,364; 5,654,737; 5,715,018; 5,724,605; 5,726,717; 5,729,673; 5,745,637; 5,752,029; 5,754,851; 5,781,188; 5,799,150; 5,812,216; 5,852,435; 5,905,841; 5,929,836; 5,929,942; 5,930,445; 5,930,797; 5,946,445; 5,987,501; 5,999,190; 6,016,152; 6,018,337; 6,023,531; 6,023,703; 6,031,529; 6,058,236; 6,061,758; 6,091,778; 6,105,083; 6,118,444; 6,128,001; 6,134,607; 6,137,919; 6,141,691; 6,157,929; 6,160,548; 6,167,404; 6,198,477; 6,201,531; 6,223,211; 6,249,280; 6,269,195; 6,317,158; 6,317,515; 6,330,369; 6,351,557; 6,353,862; 6,357,047; 6,392,710; 6,404,435; 6,407,775; 6,417,891; 6,426,778; 6,449,019; 6,473,094; 6,477,271; 6,489,969; 6,512,522; 6,532,043; 6,539,163; D396,853; D398,912. Additional U.S. and foreign patents pending.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of Avid Technology, Inc.

Copyright © 2003 Avid Technology, Inc. and its licensors. All rights reserved. Printed in USA.

Attn. Government User(s). Restricted Rights LegendU.S. GOVERNMENT RESTRICTED RIGHTS. This Software and its documentation are “commercial computer software” or “commercial computer software documentation.” In the event that such Software or documentation is acquired by or on behalf of a unit or agency of the U.S. Government, all rights with respect to this Software and documentation are subject to the terms of the License Agreement, pursuant to FAR §12.212(a) and/or DFARS §227.7202-1(a), as applicable.

Trademarks888 I/O, Adrenaline, AirPlay, AirSPACE, AirSPACE HD, AniMatte, AudioSuite, AudioVision, AutoSync, Avid, Avid DNA, AVIDdrive, AVIDdrive Towers, AvidNet, AvidNetwork, AVIDstripe, Avid Mojo, Avid Unity, Avid Xpress, AVoption, AVX, CamCutter, ChromaCurve, ChromaWheel, DAE, D-Fi, D-fx, Digidesign, Digidesign Audio Engine, Digidesign Intelligent Noise Reduction, DigiDrive, Digital Nonlinear Accelerator, DigiTranslator, DINR, D-Verb, Equinox, ExpertRender, FieldPak, Film Composer, FilmScribe, FluidMotion, HIIP, HyperSPACE, HyperSPACE HDCAM, IllusionFX, Image Independence, Intraframe, iS9, iS18, iS23, iS36, Lo-Fi, Magic Mask, make manage move | media, Marquee, Matador, Maxim, MCXpress, Media Composer, MediaDock, MediaDock Shuttle, Media Fusion, Media Illusion, MediaLog, Media Reader, Media Recorder, MEDIArray, MediaShare, Meridien, MetaSync, NaturalMatch, Nearchive, NetReview, NewsCutter, Nitris, OMF, OMF Interchange, OMM, Open Media Framework, Open Media Management, ProEncode, Pro Tools, QuietDrive, Recti-Fi, RetroLoop, rS9, rS18, Sci-Fi, Softimage, Sound Designer II, SPACE, SPACEShift, Symphony, the Avid|DS logo, Trilligent, UnityRAID, Vari-Fi, Video Slave Driver, VideoSPACE, Xdeck, and XSI are either registered trademarks or trademarks of Avid Technology, Inc. in the United States and/or other countries.

iNEWS, iNEWS ControlAir, and Media Browse are trademarks of iNews, LLC.

FireWire, Macintosh, and Mac OS are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. All other trademarks contained herein are the property of their respective owners.

Using the Avid Mojo DNA • Part 0130-05736-01 Rev. A • September 2003


28

using the avid mojo dnaresources.avid.com/supportfiles/attach/using_mojodna_0573601a.pdf · a using...

Documents