usu3910 based multi bbu interconnection(sran10.1_02)
TRANSCRIPT
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
1/89
SingleRAN
USU3910-based Multi-BBU
Interconnection Feature Parameter
Description
Issue 02
Date 2015-08-31
HUAWEI TECHNOLOGIES CO., LTD.
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
2/89
Copyright Huawei Technologies Co., Ltd. 2015. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
i
http://www.huawei.com/ -
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
3/89
Contents
1 About This Document.................................................................................................................. 1
1.1 Scope.............................................................................................................................................................................. 1
1.2 Intended Audience..........................................................................................................................................................1
1.3 Change History...............................................................................................................................................................2
1.4 Differences Between eNodeB Types..............................................................................................................................4
2 Overview......................................................................................................................................... 5
2.1 Introduction.................................................................................................................................................................... 5
2.2 Benefits...........................................................................................................................................................................5
3 Technical Description...................................................................................................................7
3.1 Introduction.................................................................................................................................................................... 7
3.2 Multi-BBU Interconnection Modes................................................................................................................................8
3.2.1 Interconnection Between BBUs and a USU................................................................................................................8
3.2.2 Interconnection Between BBUs and Two Levels of USUs....................................................................................... 113.3 Key Configurations.......................................................................................................................................................15
3.3.1 Basic Data Configurations.........................................................................................................................................15
3.3.2 Clock Data Configurations........................................................................................................................................ 26
3.3.2.1 Clock Synchronization Solution 1..........................................................................................................................27
3.3.2.2 Clock Synchronization Solution 2..........................................................................................................................28
3.3.2.3 Clock Source Backup............................................................................................................................................. 36
4 Related Features...........................................................................................................................39
5 NetworkImpact........................................................................................................................... 40
6 Engineering Guidelines............................................................................................................. 41
6.1 When to Use Multi-BBU Interconnection....................................................................................................................41
6.2 Required Information................................................................................................................................................... 41
6.3 Planning........................................................................................................................................................................41
6.4 Deployment.................................................................................................................................................................. 42
6.4.1 Process.......................................................................................................................................................................42
6.4.2 Requirements.............................................................................................................................................................43
6.4.3 Data Preparation and Feature Activation...................................................................................................................46
6.4.3.1 Data Preparation..................................................................................................................................................... 46
6.4.3.2 Activation............................................................................................................................................................... 55
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description Contents
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
ii
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
4/89
6.4.4 MML Command Examples....................................................................................................................................... 59
6.4.5 Activation Observation..............................................................................................................................................60
6.4.6 Reconfiguration......................................................................................................................................................... 62
6.4.6.1 Reconfiguration for the Centralized Cloud BB Mode............................................................................................62
6.4.6.1.1 Adding BBUs...................................................................................................................................................... 62
6.4.6.1.2 Removing BBUs..................................................................................................................................................65
6.4.6.1.3 Adding BBUs and USUs.....................................................................................................................................65
6.4.6.2 Reconfiguration for Distributed Cloud BB Mode..................................................................................................67
6.4.6.2.1 Adding BBUs...................................................................................................................................................... 67
6.4.6.2.2 Removing BBUs..................................................................................................................................................69
6.4.6.2.3 Adding BBUs and USUs.....................................................................................................................................70
6.5 Performance Monitoring...............................................................................................................................................71
6.6 Parameter Optimization................................................................................................................................................72
6.7 Troubleshooting............................................................................................................................................................72
7 Parameters.....................................................................................................................................74
8 Counters........................................................................................................................................ 83
9 Glossary.........................................................................................................................................84
10 Reference Documents...............................................................................................................85
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description Contents
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
iii
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
5/89
1About This Document
1.1 Scope
This document describes the USU3910-based multi-BBU interconnection feature, including
its technical principles, related features, network impact, and engineering guidelines.
This document covers the following features:
l TDLOFD-081213 Inter-BBU Clock Sharing
l LOFD-081220 Inter-BBU Clock Sharing
This document applies to the following types of eNodeBs.
eNodeB Type Model
Macro 3900 series eNodeB
LampSite l LTE FDD: DBS3900
l LTE TDD: DBS3900 LampSite TDD
Any managed objects (MOs), parameters, alarms, or counters described herein correspond to
the software release delivered with this document. Any future updates will be described in the
product documentation delivered with future software releases.
1.2 Intended Audience
This document is intended for personnel who:
l Need to understand the features described herein
l Work with Huawei products
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 1 About This Document
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
1
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
6/89
1.3 Change History
This section provides information about the changes in different document versions. There are
two types of changes:
l Feature change
Changes in features and parameters of a specified version as well as the affected entities
l Editorial change
Changes in wording or addition of information and any related parameters affected by
editorial changes. Editorial change does not specify the affected entities.
SRAN10.1 02 (2015-08-31)
This issue includes the following changes.
ChangeType
Change Description ParameterChange
AffectedEntity
Feature
change
Added support of the GTMUc. For details,
see 6.4.2 Requirements.
None Macro and
LampSite
eNodeBs
Added scenarios where base stations with
BBU interconnection are applicable in
centralized Cloud BB mode. For details, see
6.4.2 Requirements.
None Macro and
LampSite
eNodeBs
Editorial
change
Revised descriptions in this document. None Macro and
LampSite
eNodeBs
SRAN10.1 01 (2015-03-20)
This issue includes the following changes.
Change Type
Change Description Parameter Change
AffectedEntity
Feature
change
Added descriptions about hardware requirements and
licenses to be purchased for multi-BBU
interconnection. For details, see 6.4.2
Requirements.
None Macro and
LampSite
eNodeBs
Editoria
l
change
Revised descriptions in this document. None Macro and
LampSite
eNodeBs
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 1 About This Document
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
2
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
7/89
SRAN10.1 Draft C (2015-03-10)
This issue includes the following changes.
Chang
e Type
Change Description Paramete
r Change
Affected
Entity
Feature
change
Added descriptions about hardware requirements for
inter-BBU interconnection. For details, see 6.4.2
Requirements.
None Macro and
LampSite
eNodeBs
Editoria
l
change
Revised descriptions in this document. None Macro and
LampSite
eNodeBs
SRAN10.1 Draft B (2015-02-10)
This issue includes the following changes.
Change Type
Change Description Parameter Change
AffectedEntity
Feature
change
None None N/A
Editoria
l
change
Revised descriptions in this document. None Macro and
LampSite
eNodeBs
SRAN10.1 Draft A (2015-01-20)
Compared with Issue 01 (2014-12-30) of SRAN10.0, Draft A (2015-01-20) of SRAN10.1
includes the following changes.
Change Type
Change Description Parameter Change
AffectedEntity
Featurechange Added descriptions related to the distributed CloudBB mode. None Macro andLampSite
eNodeBs
Added the requirement that the license for clock
source sharing in a Cloud BB network be purchased
and activated on the eNodeBs that receive signals
from the clock source. For details, see 6.4.2
Requirements.
None Macro and
LampSite
eNodeBs
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 1 About This Document
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
3
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
8/89
Change Type
Change Description Parameter Change
AffectedEntity
Added the method of performing link connectivity
tests and link performance monitoring based on the
ITU-T Y.1731 protocol to locate the connectivity and
performance faults in Ethernet links. For details, see
6.7 Troubleshooting.
None Macro and
LampSite
eNodeBs
Added the service features supported in a Cloud BB
network. For details, see Service Features
Supported.
None Macro and
LampSite
eNodeBs
Editoria
l
change
None None N/A
1.4 Differences Between eNodeB Types
The features described in this document apply only to macro and LampSite eNodeBs and are
implemented in the same way on these eNodeBs.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 1 About This Document
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
4
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
9/89
2Overview
2.1 Introduction
USU3910-based multi-BBU interconnection (multi-BBU interconnection for short) allows
two or more baseband units (BBUs) to communicate with each other and process services by
connecting the BBUs and USU3910s.
NOTE
l This feature requires USU3910s and BBU3900s or BBU3910s.
l In this document, universal switching unit (USU) refers to USU3910 and BBU refers to BBU3900
and BBU3910.
After BBUs are interconnected, each USU and the eNodeB where each BBU is installed
function as independent network elements (NEs) on the U2000. A cluster of these NEs form a
Cloud BB network.
BBUs and USU are connected in either of the following modes:
l Centralized Cloud BB (Ideal Backhaul) (centralized Cloud BB for short)
l Distributed Cloud BB (Ideal Backhaul) (distributed Cloud BB for short)
In a Cloud BB network, if some BBUs connect to a USU in centralized Cloud BB mode and
other BBUs connect to this USU in distributed Cloud BB mode, this networking mode is
called the centralized Cloud BB+distributed Cloud BB mode.
2.2 Benefits
Multi-BBU interconnection provides the following benefits:
l Helps achieve inter-BBU cell coordination when features, such as Uplink Coordinated
Multiple Points Transmission (UL CoMP) based on coordinated BBU, carrier
aggregation for 2CC based on coordinated BBU, and coordinated scheduling based
power control (Cloud BB), are enabled.
l Reduces the number of required Global Positioning System (GPS) antennas because
interconnected BBUs can share GPS clock sources.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 2 Overview
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
5
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
10/89
NOTE
GPS clock sources include RGPS clock sources.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 2 Overview
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
6
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
11/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
12/89
Service Features Supported
l LTE FDD:
LOFD-070223 UL CoMP based on Coordinated BBU
LAOFD-070202 Carrier Aggregation for 2CC based on Coordinated BBU LOFD-070208 Coordinated Scheduling based Power Control (Cloud BB)
LOFD-081208 Inter-eNodeB SFN Based on Coordinated BBU
LOFD-081209 Inter-eNodeB Adaptive SFN/SDMA Based on Coordinated BBU
l LTE TDD:
TDLOFD-001080 Inter-BBU SFN
TDLOFD-001082 Inter-BBU Adaptive SFN/SDMA
TDLOFD-081207 UL CoMP based on Coordinated BBU
TDLOFD-080203 Coordinated Scheduling based Power Control (Cloud BB)
3.2 Multi-BBU Interconnection Modes
3.2.1 Interconnection Between BBUs and a USU
The requirements on BBUs and the USU are as follows:
l BBU3900s and BBU3910s can be connected to the same first-level USU.
l In the USU, a universal enhanced switch fabric unit (UEFU) and a universal line process
unit (ULPU) must be available and are always installed in slots 0 and 1, respectively.
l eNodeBs connecting to the USU are classified into two types:
An eNodeB configured with one BBU: The BBU is directly connected to the USU.
An eNodeB configured with two interconnected BBUs: The BBU configured with
the UMPT and UCIU connects to the USU.
NOTE
For restrictions on multi-BBU interconnection, seeMulti-BBU Interconnection Feature
Parameter Description.
Centralized Cloud BB
l Cable connections
BBUs and USUs are connected using the following types of cables:
Cascading interface (CI) interconnection cable: This type of cable connects the CI
port on the UMPT in a BBU and a CI-DL port (S0 to S11) on the UEFU in the
USU.
The cable transmits control information about the topology, clock, heartbeat, and
inter-cell link setup and release.
High speed extension interface (HEI) interconnection cable for short-distance
connection: This type of cable connects the HEI port on a baseband processing unit
(BBP) in a BBU and an HEI port (P0 to P29) on the ULPU in the USU.
The cable transmits cell coordination information.
l Configuration principles
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
8
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
13/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
14/89
Each eNodeB must be configured with only one UCCU. Slots 3, 2, 4, 5, 1, and 0 for
the UCCU are prioritized in descending order.
NOTE
If the UCCU is installed in slot 0, 1, 4, or 5 instead of slot 2 or 3, it must connect to BBPs
using baseband interconnection cables, as shown in Figure 3-4.
Figure 3-4Connection between the UCCU and BBPs
l Example
Figure 3-5shows the interconnection between BBUs and a USU in distributed
Cloud BB mode when each BBU and the USU are connected using two opticalcables.
Figure 3-5Interconnection between BBUs and a USU in distributed Cloud BB
mode (1)
Figure 3-6shows the interconnection between BBUs and a USU in distributed
Cloud BB mode when each BBU and the USU are connected using one optical
cable.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
10
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
15/89
Figure 3-6Interconnection between BBUs and a USU in distributed Cloud BB
mode (2)
Centralized Cloud BB+Distributed Cloud BB
In centralized Cloud BB+distributed Cloud BB mode, BBUs connected in centralized mode
and those connected in distributed mode co-exist. However, a BBU can be connected either in
centralized or distributed mode, as shown in Figure 3-7.
Figure 3-7Interconnection between BBUs and a USU in centralized Cloud BB+distributed
Cloud BB mode
3.2.2 Interconnection Between BBUs and Two Levels of USUs
Interconnection between BBUs and two levels of USUs involves the following types of cableconnections:
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
11
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
16/89
l Between first- and second-level USUs
l Between second-level USUs in centralized Cloud BB mode
First- and second-level USUs are connected in either centralized or distributed Cloud BB
mode.
NOTE
l In each USU, a UEFU is always installed in slot 0 regardless of centralized or distributed Cloud BB
mode.
l First- and second-level USUs cannot be connected in centralized Cloud BB+distributed Cloud BB
mode.
l Within a Cloud BB network, the interconnection between first- and second-level USUs and that
between first-level USUs and BBUs are independent.
Centralized Cloud BB
l Cable connections
First- and second-level USUs are connected using the following types of cables:
CI interconnection cable: This type of cable connects the CI-UL port on a first-level
USU and a CI-DL port on the second-level USU that functions as a server and
whoseNodeIDis set to 0. It is used to transmit control and synchronization
information.
FABRIC interconnection cable: This type of cable connects the FABRIC ports on a
first-level USU and a second-level USU. It is used to transmit BBU-related data.
When two second-level USUs are configured, they are connected only using a CI
interconnection cable. This cable connects the CI-UL port on a second-level USU (that
does not function as a server and whoseNodeIDis not set to 0) and the CI-DL port on
the other second-level USU (that functions as a server and whoseNodeIDis set to 0).
l Configuration principles
Each first-level USU must connect to four FABRIC interconnection cables. These
cables connect to two FABRIC ports on each UEFU in the second-level USU if
only one second-level USU is configured, or connect to a FABRIC port on each
UEFU in two second-level USUs if two second-level USUs are configured.
Connections of FABRIC interconnection cables have no requirements for FABRIC
port numbers.
NOTE
(Optional) If the number of first-level USUs connected to a second-level USU does not
exceed three, the second-level USU can use only one UEFU. The first-level USUs are
connected to the second-level USE through four FABRIC interconnection cables andconnections of FABRIC interconnection cables have no requirements for FABRIC port
numbers. This configuration reduces transmission reliability but cuts deployment costs.
Two UEFUs must be installed in slots 0 and 1 in a second-level USU.
A maximum of two second-level USUs can be deployed in a Cloud BB network.
When 2 to 6 first-level USUs are configured, 1 second-level USU is required. When
7 to 12 first-level USUs are configured, 2 second-level USUs are required.
A second-level USU can connect to a maximum of 12 first-level USUs.
The longest distance between first- and second-level USUs is 90 m.
l Example
Figure 3-8shows the cable connections between USUs in centralized Cloud BB modewhen only one second-level USU is configured (with two UEFUs). Figure 3-9shows the
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
12
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
17/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
18/89
Figure 3-10Cable connections between USUs in centralized Cloud BB mode when two
second-level USUs are configured
Distributed Cloud BB
l Cable connectionsHEI interconnection cable for long-distance connection: This type of cable connects the
HEI ports (which work in 1*40GE mode) on the ULPUs in first- and second-level USUs.
l Configuration principles
The second-level USU provides a maximum of 30 HEI ports. When each first-level
USU connects to 5 HEI ports on the second-level USU, a maximum of 6 first-level
USUs can connect tothe second-level USU.
The longest distance between first- and second-level USUs is 10 km.
HEI ports 25 to 29 on a first-level USU connect to the HEI ports on the second-
level USU by using five optical cables without the requirements of mapping
between the port numbers.
A ULPU must be installed in slot 1 in the second-level USU.
Only one second-level USU can be deployed in a Cloud BB network.
NOTE
When 2 to 6 first-level USUs are configured, 1 second-level USU is required.
l Example
Figure 3-11shows the cable connections between USUs in distributed Cloud BB mode.
Figure 3-11Cable connections between USUs in distributed Cloud BB mode
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
14
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
19/89
3.3 Key Configurations
3.3.1 Basic Data Configurations
This section describes the basic configurations required for eNodeBs, first-level USUs, and
second-level USUs in centralized and distributed Cloud BB modes.
The configuration principles are as follows:
NOTE
The MML commands listed in the section are used as examples and only key parameter settings are
provided. Otherparameters,such as Cabinet No., Subrack No., and Slot No., must be set based on the
actual configuration.
l Principles for setting the CLOUDBBIDandNODEIDparameters
The CLOUDBBIDparameter must be set to the same value for all the eNodeBs and
USUs in a Cloud BB network.
TheNODEIDparameter must be set to a unique value for each of the USUs at the
same level in a Cloud BB network.
In a Cloud BB network, if only one second-level USU is configured, theNODEID
parameter must be set to 0for this USU; if two second-level USUs are configured,
theNODEIDparameter must be set to 0for the USU functioning as a server and set
to a non-zero value for the other USU.
l Principles for setting the IP addresses
In a Cloud BB network, the following IP addresses are involved in basic data
configurations:
In centralized Cloud BB: IP address of the HEI port on the ULPU in the USU
In centralized Cloud BB: IP address of the CI port on the UMPT in the BBU
In distributed Cloud BB: M5/S0 port on the UCCU in the BBU
The preceding IP addresses must be set based on the following principles:
The IP addresses must belong to the same network segment.
The IP addresses must be unique in the Cloud BB network.
The IP addresses cannot belong to the same network segment as the O&M IP
addresses or interface (such as S1 and X2) IP addresses.
Data Configuration on an eNodeB
l Table 3-1describes the data configuration on an eNodeB in centralized Cloud BB mode.
Table 3-1Data configuration on an eNodeB in centralized Cloud BB mode
Configuration Operation MML Command Example
Specify a Cloud BB ID for an eNodeB. SET NE: CLOUDBBID=666;
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
15
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
20/89
Configuration Operation MML Command Example
Turn on the alarm detection switch for
interconnection ports.
l Turn on the alarm detection switch for
the CI port on a UMPT connecting to
a USU.
SET CASCADEPORT: CN=0,
SRN=0, SN=7, PN=8, SW=ON;
In this command, set thePN
parameter to 8.
l Turn on the alarm detection switch for
the HEI port on a BBP connecting to a
USU.
SET CASCADEPORT: CN=0,
SRN=0, SN=3, PN=6, SW=ON;
In this command, set thePN
parameter to 6.
Configure a CI port and the IP address. l Configure an Ethernet CI port.
ADD
ETHCIPORT:SN=7,SBT=BASE_BO
ARD;
In this command, set the SN
parameter to the number of the slot in
which the main control board is
installed.
l Set the IP address for an Ethernet CI
port.
ADD DEVIP: CN=0, SRN=0, SN=7,SBT=BASE_BOARD, PT=ETHCI,
PN=0, IP="192.168.2.24",
MASK="255.255.255.0";
In this command, always set theSBT
parameter to BASE_BOARD, thePN
parameter to 0, and thePTparameter
to ETHCI.
l Table 3-2describes the data configuration on an eNodeB in distributed Cloud BB mode.
Table 3-2Data configuration on an eNodeB in distributed Cloud BB mode
Configuration Operation MML Command Example
Specify a Cloud BB ID for an
eNodeB.
SET NE: CLOUDBBID=666;
Add a UCCU. ADD BRD: CN=0, SRN=0, SN=3,
BT=UCCU;
In this command, set theSNparameter
according to the slot where the UCCU is
installed.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
16
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
21/89
Configuration Operation MML Command Example
Configure one Ethernet port.
(Connect a BBU to a USU using an
optical cable that is used for both
transmission and reception.)
ADD ETHPORT: CN=0, SRN=0, SN=3,
SBT= ETH_COVERBOARD, PN=2,
PA=FIBER, MTU=1500, SPEED=10G,
DUPLEX=FULL, FC=OPEN;
In this command:
l Set theSBTparameter to
ETH_COVERBOARD.
l Set thePNparameter as follows:
When the optical module is inserted in
port A on the UCCU, set this parameter
to 2.
When the optical module is inserted in
port B on the UCCU, set this parameter
to 3.
l Always set theSPEEDparameter to
10G(10G).
Configure two Ethernet ports.
(Connect a BBU to a USU using two
optical cables that are used for both
transmission and reception.)
l Configure two Ethernet ports.
ADD ETHPORT: CN=0, SRN=0,
SN=3, SBT= ETH_COVERBOARD,
PN=2, PA=FIBER, MTU=1500,
SPEED=10G, DUPLEX=FULL,
FC=OPEN;
ADD ETHPORT: CN=0, SRN=0,
SN=3, SBT= ETH_COVERBOARD,PN=3, PA=FIBER, MTU=1500,
SPEED=10G, DUPLEX=FULL,
FC=OPEN;
l Configure an Ethernet trunk.
ADD ETHTRK: CN=0, SRN=0, SN=3,
SBT= ETH_COVERBOARD, TN=0;
l Add member ports to the Ethernet trunk.
ADD ETHTRKLNK: CN=0, SRN=0,
SN=3, SBT= ETH_COVERBOARD,
TN=0, PN=2, PRI=255, FLAG=YES;
ADD ETHTRKLNK: CN=0, SRN=0,
SN=3, SBT= ETH_COVERBOARD,
TN=0, PN=3, PRI=255, FLAG=NO;
NOTE
In an Ethernet trunk, the port whose FLAG
is set to YESfunctions as the primary port.
Each Ethernet trunk is configured with only
one primary port.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
17
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
22/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
23/89
Configuration Operation MML Command Example
Set the working mode of HEI ports on the
ULPU to SCPRI/SRIO. (Skip this step if
the HEI ports already work in SCPRI/
SRIO mode.)
Set the working mode of the port
connecting a first-level USU and a BBU.
(Assume that HEI ports 0 to 24 on the
ULPU can be used for multi-BBU
interconnection.)
SET
PORTMODE:CN=0,SRN=0,SN=1,STPN
=0,ETPN=24,PM=SCPRI/SRIO;
If first- and second-level USUs are
connected in distributed mode, set the
working mode of the port connecting the
first-and second-level USUs.
SET
PORTMODE:CN=0,SRN=0,SN=1,STPN=25,ETPN=29,PM=40GE;
NOTE
If first- and second-level USUs are connected
in centralized mode, the interconnection cable
does not occupy ULPU ports. In this case, you
are not required to set the working mode for
the port connecting the first- and second-level
USUs.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
19
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
24/89
Configuration Operation MML Command Example
Turn on the alarm detection switch for
interconnection ports.
l Turn on the alarm detection switch for
the CI-DL port on the UEFU.
SET CASCADEPORT: CN=0,
SRN=0, SN=0, PT=CI-DL, PN=0,
SW=ON;
In this command, set theSN
parameter to 0and thePNparameter
to a value ranging from 0 to 11.
l Turn on the alarm detection switch for
the CI-UL port on the UEFU.
SET CASCADEPORT: CN=0,
SRN=0, SN=0, PT=CI-UL, PN=0,
SW=ON;
In this command, set theSNparameter to 0and thePNparameter
to 0or 1.
l Turn on the alarm detection switch for
a FABRIC port on the UEFU.
SET CASCADEPORT: CN=0,
SRN=0, SN=0, PT=FABRIC, PN=0,
SW=ON;
In this command, set theSN
parameter to 0and thePNparameter
to a value ranging from 0 to 11.
lTurn on the alarm detection switch foran HEI port on the ULPU.
SET CASCADEPORT: CN=0,
SRN=0, SN=1, PT=HEI, PN=0,
SW=ON;
In this command, set thePN
parameter to a value ranging from 0 to
29.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
20
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
25/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
26/89
Table 3-4Data configuration on a first-level USU in distributed Cloud BB mode
Configuration Operation MML Command Example
Specify a Cloud BB ID for a
USU.
SET NE: CLOUDBBID=666;
Specify the USU working mode. SET GTRANSPARA:Level=LEVEL1,
NETMODE=DISTRIBUTED, NodeID=0;
In this command, set theNodeIDparameter to a
value ranging from 0 to 11.
Specify the name of an eNodeB
connecting to a USU.
ADD INTERCONNE:
NENAME="JINQIAO_eNODE1";
Set the working mode of HEI
ports on the ULPU.
l Set the working mode of the ports connecting
first-level USUs and BBUs that are connected
in distributed mode.
SET PORTMODE: CN=0, SRN=0, SN=1,
STPN=0, ETPN=24, PM=10GE;
In this command, always set thePM
parameter to 10GE(10GE).
l Set the working mode of the ports connecting
first- and second-level USUs that are
connected in distributed mode.
SET PORTMODE: CN=0, SRN=0, SN=1,
STPN=25, ETPN=29, PM=40GE;
In this command, set thePMparameter to
40GE.
NOTE
If first- and second-level USUs are connected in
centralized mode, the interconnection cable does
not occupy ULPU ports. In this case, you are not
required to set the working mode for the port
connecting the first- and second-level USUs.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
22
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
27/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
28/89
Configuration Operation MML Command Example
Set up an Ethernet trunk for five
ports working in 1x40GE mode
(HEI port numbers: 25 to 29; the
corresponding Ethernet port
numbers: 100, 104, 108, 112, and
116).
l ADD ETHTRK: CN=0, SRN=0, SN=1,
SBT=ETH_COVERBOARD, TN=0;
lADD ETHTRKLNK: CN=0, SRN=0, SN=1,SBT= ETH_COVERBOARD, TN=0,
PN=100, PRI=255, FLAG=YES;
l ADD ETHTRKLNK: CN=0, SRN=0, SN=1,
SBT= ETH_COVERBOARD, TN=0,
PN=104, PRI=255, FLAG=NO;
l ADD ETHTRKLNK: CN=0, SRN=0, SN=1,
SBT= ETH_COVERBOARD, TN=0,
PN=108, PRI=255, FLAG=NO;
l ADD ETHTRKLNK: CN=0, SRN=0, SN=1,
SBT= ETH_COVERBOARD, TN=0,
PN=112, PRI=255, FLAG=NO;
l ADD ETHTRKLNK: CN=0, SRN=0, SN=1,
SBT= ETH_COVERBOARD, TN=0,
PN=116, PRI=255, FLAG=NO;
Data Configuration on a Second-Level USU
l Table 3-5describes the data configuration on a second-level USU in centralized Cloud
BB mode.
Table 3-5Data configuration on a second-level USU in centralized Cloud BB mode
Configuration Operation MML Command Example
Specify a Cloud BB ID for a USU. SET NE: CLOUDBBID=666;
Specify the USU working mode. SET GTRANSPARA: Level=LEVEL2,
NETMODE =CENTRALIZED,
NodeID=0;
In this command, set theNodeID
parameter to a value ranging from 0 to 5.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
24
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
29/89
Configuration Operation MML Command Example
Turn on the alarm detection switch for
interconnection ports.
l Turn on the alarm detection switch for
the CI-DL port on the UEFU in the
second-level USU whoseNodeIDis
set to 0.
SET CASCADEPORT: CN=0,
SRN=0, SN=0, PT=CI-DL, PN=0,
SW=ON;
In this command, set thePN
parameter to a value ranging from 0 to
11.
l Turn on the alarm detection switch for
the CI-UL port on the UEFU in the
second-level USU whoseNodeIDis
not set to 0when two second-level
USUs are configured.
SET CASCADEPORT: CN=0,
SRN=0, SN=1, PT=CI-UL, PN=0,
SW=ON;
In this command, set thePN
parameter to 0or 1.
l Turn on the alarm detection switch for
a FABRIC port on the UEFU.
SET CASCADEPORT: CN=0,
SRN=0, SN=1, PT=FABRIC, PN=0,
SW=ON;
In this command, set thePN
parameter to a value ranging from 0 to
11.
Table 3-6describes the data configuration on a first-level USU in distributed Cloud BB
mode.
Table 3-6Data configuration on a second-level USU in distributed Cloud BB mode
Configuration Operation MML Command Example
Specify a Cloud BB ID for a USU. SET NE: CLOUDBBID=666;
Specify the USU working mode. SET GTRANSPARA: Level=LEVEL2,
NETMODE=DISTRIBUTED, NodeID=0;
In this command, set theNodeIDparameter
to a value ranging from 0 to 5.
Set the working mode of HEI ports on the
ULPU.
SET PORTMODE: CN=0, SRN=0, SN=1,
STPN=27, ETPN=28, PM=40GE;
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
25
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
30/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
31/89
l Solution 1: Each BBU is configured with a clock source for time synchronization, and
the USU clock works in free-run mode.
l Solution 2: One BBU or USU is configured with a clock source for time synchronization
and shares the clock source with other interconnected BBUs or connected USUs.
For details about how to configure these features, see 6.4.3.2 Activation.
3.3.2.1 Clock Synchronization Solution 1
Solution Description
This solution applies when a clock source is available for each BBU. Figure 3-12shows
clock synchronization solution 1.
Figure 3-12Clock synchronization solution 1
Clock Data Configuration
Table 3-7describes the clock data configuration on a USU and an eNodeB.
Table 3-7Clock data configuration on a USU and an eNodeB
NE Type MML Command for ClockSynchronization Configuration
Description
USU Setting the working mode of the referenceclock
SET CLKMODE: MODE=FREE;
In this command, set theMODEparameter to
FREE(Free).
The USU works in free-runmode.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
27
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
32/89
NE Type MML Command for ClockSynchronization Configuration
Description
eNodeB 1. Adding a GPS or an IP clock link
lADD GPS: GN=0, CN=0, SRN=0,SN=7, CABLE_LEN=1000,
MODE=GPS, PRI=4;
l ADD IPCLKLINK: LN=0, ICPT=PTP,
SN=7, CNM=L2_MULTICAST,
DELAYTYPE=E2E, MACMODE=NO,
PROFILETYPE=1588V2;
2. Setting the working mode of the reference
clock
SET CLKMODE: MODE=MANUAL,
CLKSRC=GPS, SRCNO=0;
In this command, set the CLKSRCparameter to GPS(GPS Clock)or
IPCLK(IP Clock).
3. Setting the eNodeB clock synchronization
mode
SET CLKSYNCMODE:
CLKSYNCMODE=TIME,
SYSCLKSRC=LOCAL;
In this command, set the CLKSYNCMODE
parameter to TIME(TIME)and the
SYSCLKSRCparameter to LOCAL(Local
Standard Clock).
Each BBU is configured
with a clock source for time
synchronization.
3.3.2.2 Clock Synchronization Solution 2
Solution Description
This solution applies when a clock source can be shared between BBUs and USUs in a Cloud
BB network. When BBUs are interconnected and one NE obtains a clock synchronization
source, other NEs can share the clock synchronization source.
l Figure 3-13shows the clock synchronization solution when a USU provides a GPS/IPCLK clock source for time synchronization.
l Figure 3-14shows the clock synchronization solution when a BBU provides a GPS
clock source for time synchronization.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
28
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
33/89
Figure 3-13Clock synchronization solution when a USU provides a clock source for time
synchronization
Figure 3-14Clock synchronization solution when a BBU provides a clock source for time
synchronization
NOTE
In the solution shown in Figure 3-14, after receiving clock signals from BBU0, USU1 forwards the
clock signals to the second-level USU (USU0) and the other connected BBU (BBU1).
Clock Data Configuration
Clock synchronization scenarios are classified based on the following aspects:
l NE type: BBU or USU
l
NE function in clock synchronization: providing a clock source for time synchronization,receiving clock signals, or forwarding clock signals
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
29
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
34/89
Clock signal transmission bearer mode:
Centralized Cloud BB
Distributed Cloud BB
Transmission from the clock source provider in centralized Cloud BB mode to a
clock signal receiver in distributed Cloud BB mode
Transmission from the clock source provider in distributed Cloud BB mode to a
clock signal receiver in centralized Cloud BB mode
Clock data configuration on an eNodeB and a USU varies with clock synchronization
scenarios.
NOTE
l In theIPCLKLINKMO, when theDEVTYPEparameter is set to OC_MASTERor BC, set theLN
parameter to 2; when theDEVTYPEparameter is set to OC_SLAVE, set theLNparameter to 0or
1.
l Always set the CLKSYNCMODEparameter to TIME(TIME)for both eNodeBs and USUs except
when the USUs works in free-run mode.
l When a USU provides a clock source for time synchronization, the USU must use the GPS or IEEE
1588v2 clock as the clock source for its own synchronization. When an eNodeB provides a clock
source for time synchronization, the eNodeB must use the GPS clock source for its own
synchronization. Set the CLKSYNCMODEparameter to TIME(TIME)for the USU and eNodeB
that provide clock sources for time synchronization.
l Table 3-8describes the clock data configuration on an eNodeB.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
30
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
35/89
Table 3-8Clock data configuration on an eNodeB
Scenario
NEFunction
ClockSignalTrans
missionBearerMode
MML Command forSynchronization ObjectConfiguration
MMLCommandfor System
ClockModeSetting
MMLCommand forClock Sharing
Mode Setting
1 Provi
ding
a
clock
sourc
e for
time
synchroniz
ation
Central
ized
Cloud
BB
1. ADD GPS: GN=0,
CN=0, SRN=0, SN=7,
CABLE_LEN=20,
MODE=GPS, PRI=1;
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=GPS,
SRCNO=0;
If two eNodeBs in a Cloud
BB network provides
clock sources, run the
following commands to
enable the eNodeB whose
external clock source
becomes faulty to obtain
clock signals from the
other eNodeB:
1. ADD GPS: GN=0,
CN=0, SRN=0, SN=7,CABLE_LEN=20,
MODE=GPS, PRI=1;
2. ADD INTERCLK:
LN=0;
In this command,
always set theLN
parameter to 0.
3. SET CLKMODE:
MODE=AUTO;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME,
SYSCLKS
RC=LOCAL;
SET
CLOUDSRC:
CLOUDSRC=E
NABLE;
2 Providing
a
clock
sourc
e for
time
synch
roniz
ation
Distributed
Cloud
BB
1. ADD GPS: GN=0,CN=0, SRN=0, SN=7,
CABLE_LEN=1000,
MODE=GPS, PRI=4;
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=GPS,
SRCNO=0;
SETCLKSYNC
MODE:
CLKSYNC
MODE=TI
ME,
SYSCLKS
RC=LOCA
L;
ADDIPCLKLINK:
LN=2,
ICPT=PTP,
DEVTYPE=OC
_MASTER,
CNM=L2_MU
LTICAST,
PROFILETYPE
=1588V2;
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
31
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
36/89
Scenario
NEFunction
ClockSignalTransmissi
onBearerMode
MML Command forSynchronization ObjectConfiguration
MMLCommandfor SystemClock
ModeSetting
MMLCommand forClock SharingMode Setting
3 Recei
ving
clock
signal
s
Central
ized
Cloud
BB
1. ADD INTERCLK:
LN=0;
In this command,
always set theLN
parameter to 0.
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=INTERCLK
, SRCNO=0;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME,
SYSCLKS
RC=LOCA
L;
N/A
4 Recei
ving
clock
signal
s
Distrib
uted
Cloud
BB
1. ADD IPCLKLINK:
LN=0, ICPT=PTP,
SN=2,
CNM=L2_MULTICAS
T, DELAYTYPE=E2E,
MACMODE=NO,
PROFILETYPE=1588
V2;
SNis set to the slot
number of the UCCU.
2. SET CLKMODE:MODE=MANUAL,
CLKSRC=IPCLK,
SRCNO=0;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME,
SYSCLKS
RC=LOCA
L;
N/A
l Table 3-9describes the clock data configuration on a USU.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
32
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
37/89
Table 3-9Clock data configuration on a USU
Scenario
NEFunction
ClockSignalTrans
missionBearerMode
MML Command forSynchronization ObjectConfiguration
MMLCommandfor System
ClockModeSetting
MMLCommand forClock Sharing
Mode Setting
1 Provi
ding
a
clock
sourc
e for
time
synchroniz
ation
Central
ized
Cloud
BB
l GPS clock sharing
1. ADD GPS: GN=0,
CN=0, SRN=0,
SN=0,
CABLE_LEN=20,
MODE=GPS,
PRI=4;
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=GPS,
SRCNO=0;
l IP clock sharing
1. ADD IPCLKLINK:
LN=0, SN=0,
ICPT=PTP,
CNM=L2_MULTIC
AST,
DELAYTYPE=E2E
, MACMODE=NO,
PROFILETYPE=15
88V2;
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=IPCLK,
SRCNO=0;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME;
SET
CLOUDSRC:
CLOUDSRC=E
NABLE;
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
33
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
38/89
Scenario
NEFunction
ClockSignalTransmissi
onBearerMode
MML Command forSynchronization ObjectConfiguration
MMLCommandfor SystemClock
ModeSetting
MMLCommand forClock SharingMode Setting
2 Provi
ding
a
clock
sourc
e for
time
synch
ronization
Distrib
uted
Cloud
BB
l GPS clock sharing
1. ADD GPS: GN=0,
CN=0, SRN=0,
SN=0,
CABLE_LEN=20,
MODE=GPS,
PRI=4;
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=GPS,
SRCNO=0;
l IP clock sharing
1. ADD IPCLKLINK:
LN=0, SN=0,
ICPT=PTP,
CNM=L2_MULTIC
AST,
DELAYTYPE=E2E
, MACMODE=NO,
PROFILETYPE=1588V2;
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=IPCLK,
SRCNO=0;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME;
ADD
IPCLKLINK:
LN=2,
ICPT=PTP,
DEVTYPE=OC
_MASTER,
CNM=L2_MU
LTICAST,
PROFILETYPE=1588V2;
3 Forw
ardin
g
clock
signal
s
Central
ized
Cloud
BB
Set the clock mode to free-
run to prevent an alarm.
SET CLKMODE:
MODE=FREE;
N/A N/A
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
34
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
39/89
Scenario
NEFunction
ClockSignalTransmissi
onBearerMode
MML Command forSynchronization ObjectConfiguration
MMLCommandfor SystemClock
ModeSetting
MMLCommand forClock SharingMode Setting
4 Forw
ardin
g
clock
signal
s
Distrib
uted
Cloud
BB
1. ADD IPCLKLINK:
LN=2, ICPT=PTP,
DEVTYPE=BC,
CNM=L2_MULTICAS
T,
PROFILETYPE=1588
V2;
2. SET CLKMODE:
MODE=MANUAL,CLKSRC=IPCLK,
SRCNO=2;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME;
N/A
5 Forw
ardin
g
clock
signal
s
Trans
missio
n from
the
clock
source
provid
er in
centralized
Cloud
BB
mode
to a
clock
signal
receive
r in
distrib
uted
CloudBB
mode
1. ADD INTERCLK:
LN=0;
2. SET CLKMODE:
MODE=MANUAL,
CLKSRC=INTERCLK
, SRCNO=0;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME;
ADD
IPCLKLINK:
LN=2,
ICPT=PTP,
DEVTYPE=OC
_MASTER,
CNM=L2_MU
LTICAST,
PROFILETYPE=1588V2;
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
35
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
40/89
Scenario
NEFunction
ClockSignalTransmissi
onBearerMode
MML Command forSynchronization ObjectConfiguration
MMLCommandfor SystemClock
ModeSetting
MMLCommand forClock SharingMode Setting
6 Forw
ardin
g
clock
signal
s
Trans
missio
n from
the
clock
source
provid
er in
distributed
Cloud
BB
mode
to a
clock
signal
receive
r in
central
ized
CloudBB
mode
1. ADD IPCLKLINK:
LN=2, ICPT=PTP,
DEVTYPE=BC,
CNM=L2_MULTICAS
T,
PROFILETYPE=1588
V2;
2. SET CLKMODE:
MODE=MANUAL,CLKSRC=IPCLK,
SRCNO=2;
SET
CLKSYNC
MODE:
CLKSYNC
MODE=TI
ME;
SET
CLOUDSRC:
CLOUDSRC=E
NABLE;
3.3.2.3 Clock Source Backup
In a Cloud BB network, two NEs can provide clock sources for backup to ensure that clock
signals are available for time synchronization when the clock source on one of the NEs is
faulty.
The two NEs must be of the same type, such as:
l Two eNodeBs
l Two first-level USUs
l Two second-level USUs in centralized Cloud BB mode
The restrictions on clock source backup in a Cloud BB network are as follows:
l When two eNodeBs provide GPS clock sources:
For clock signal receivers:
Clock signal receivers can maintain time synchronization when all NEs in the
network are connected in either centralized or distributed Cloud BB mode and the
clock source on one of the providers works properly.
For clock source providers:
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
36
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
41/89
The two clock source providers can implement clock source backup only when both
of them connect to the first-level USUs in centralized Cloud BB mode. If one BBU
fails to provide the clock source, NEs can obtain the clock source from the other
BBU. As shown in Figure 3-15, BBU0 and BBU2 can serve as backups of each
other.
Figure 3-15Example
NOTE
In figures in this section, the arrows indicate the transmission direction of the clock source.
l When two first-level USUs provide clock sources:
For clock signal receivers (BBUs connected to USUs that do not provide clock
sources):A clock source can be shared by NEs in a Cloud BB network when a clock source
provider works properly.
For clock source providers:
The two clock source providers can implement clock source backup only when all
first-level USUs connect to second-level USUs in centralized Cloud BB mode.
Figure 3-16Example
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
37
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
42/89
That is, if the first-level USUs connect to a second-level USU in distributed Cloud
BB mode, as shown in Figure 3-17, BBU2 and BBU3 cannot receive clock signals
from USU0 when the clock source on USU1 is faulty. The reasons are as follows:
In distributed Cloud BB mode, the clock source is transmitted in a unidirectional
manner. That is, the second-level USU can only receive clock resource signals fromthe first-level USU that functions as a clock source provider, but cannot obtain
signals from other clock source providers.
Figure 3-17Example
l When two second-level USUs implement clock source backup, NEs in the Cloud BB
network can receive signals if one clock source provider works properly,
If a second-level USU that does not function as a server provides the clock source, the
clock signals can be transmitted to other NEs through second-level USUs that function
as servers, as shown in Figure 3-18.
Figure 3-18Non-server second-level USU providing the clock source
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 3 Technical Description
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
38
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
43/89
4Related FeaturesPrerequisite Features
None
Mutually Exclusive Features
None
Impacted Features
None
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 4 Related Features
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
39
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
44/89
5Network ImpactSystem Capacity
The multi-BBU interconnection feature has no impact on system capacity. However, the
features impacted by the multi-BBU interconnection feature (as described in Service
Features Supported) can increase system capacity after the multi-BBU interconnection
feature is enabled. This is because the multi-BBU interconnection feature facilitates inter-
BBU cell coordination.
For details about the impact of these features on system capacity, see the relevant feature
parameter descriptions.
Network Performance
The multi-BBU interconnection feature has no impact on network performance. However, thefeatures impacted by the multi-BBU interconnection feature (as described in Service
Features Supported) can enhance network performance after the multi-BBU interconnection
feature is enabled. This is because the multi-BBU interconnection feature facilitates inter-
BBU cell coordination.
For details about the impact of these features on network performance, see the relevant feature
parameter descriptions.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 5 Network Impact
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
40
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
45/89
6Engineering Guidelines
6.1 When to Use Multi-BBU Interconnection
This feature applies to the following scenarios:
l Inter-BBU cell coordination is required when one of the supported service features is
enabled. For details about these service features, see Service Features Supported.
l Multiple NEs in a Cloud BB network share GPS clock sources.
6.2 Required Information
Collect the initial configurations of the BBUs and USUs involved in multi-BBU
interconnection. For details, see 3900 Series Base Station Initial Configuration Guideand
USU3910 Initial Configuration Guide.
6.3 Planning
Network Planning
l Multi-BBU interconnection has no impact on the existing transmission over the S1 or X2
interface or operation and maintenance (O&M) channel. The transmission plan in multi-
BBU interconnection scenarios is the same as that when BBUs are not interconnected. Atransmission link between a BBU and USU must be added to implement inter-BBU cell
coordination.
l A USU must set up an O&M channel with the U2000 through the FE/GE0 or FE/GE1
port.
Hardware Planning
For details about BBU and USU installation positions in cabinets, seeBase Station Cabinets
and Subracks (Including the BBU Subrack) Configuration Feature Parameter Description.
After the installation positions have been planned, plan USU hardware according to 3.2.1
Interconnection Between BBUs and a USUand 3.2.2 Interconnection Between BBUs andTwo Levels of USUs.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
41
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
46/89
6.4 Deployment
6.4.1 Process
Figure 6-1shows the process for deploying the multi-BBU interconnection feature.
Figure 6-1Process
NOTE
The data preparation in this document only involves adjusting the configurations associated with
interconnection between the BBU and USU in the preceding figure. As for other steps:
l For details about eNodeB and USU3910 installation, see 3900 Series Base Station Installation Guide
and USU3910 Installation Guide, respectively.
l For details about initial configuration of NEs, see 3900 Series Base Station Initial Configuration
Guideand USU3910 Initial Configuration Guide.
l
For details about feature-related configurations on the BBU, see eX2 Self-Management FeatureParameter Descriptionand the relevant feature parameter descriptions.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
42
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
47/89
6.4.2 Requirements
Hardware
Table 6-1describes the configuration restrictions of boards in the BBU.
Table 6-1Board configuration restrictions
Networking
Type of theBase StationConnecting tothe USU
Main Control Board/BBP UCCU
Centrali
zed
Cloud
BB
With one BBU l The main control board that directly connects
to the USU must be a UMPT, including
UMPTa1/UMPTa2/UMPTa6 and UMPTb1/
UMPTb2.l The BBP that directly connects to the USU
must be any of the following:
LBBPd, including LBBPd1 to LBBPd4
UBBPd, including UBBPd1 to UBBPd6
and UBBPd9
l UMPT backup is not supported.
Not
require
d
With
interconnected
BBUs
NOTEBBU
interconnection
applies only to
the following
scenario:
l Root BBU
(LTE) + leaf
BBU
(UMTS)
l Root BBU
(GL)+ leaf
BBU
(UMTS)
l The BBUs must be connected in UCIU+UMPT
mode. The UCIU can be installed only in the
BBU in LTE mode.
l In LTE mode, one UMPT or two UMPTs
working in load sharing mode can be used.
Not
require
d
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
43
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
48/89
Networking
Type of theBase StationConnecting tothe USU
Main Control Board/BBP UCCU
Either of the
preceding types
When the base station is connected with a USU,
l If the base station has GL SDR RF modules,
the GSM main control board cannot be the
GTMU, but can be the GTMUb or GTMUc.
l If the base station has UL SDR RF modules,
the UMTS main control board cannot be a
WMPT.
l In LTE mode, one UMPT or two UMPTs
working in load sharing mode can be used.
l UMPT backup is not supported.
Not
require
d
Distribu
ted
Cloud
BB
All scenarios When the base station is connected with a USU,
l If the base station has GL SDR RF modules,
the GSM main control board cannot be the
GTMU, but can be the GTMUb or GTMUc.
l If the base station has UL SDR RF modules,
the UMTS main control board cannot be a
WMPT.
l In LTE mode, one UMPT or two UMPTs
working in load sharing mode can be used.
l UMPT backup is not supported.
Not
require
d
NOTE
The GTMU is classified into the sub-type GTMU, GTMUb, and GTMUc.
License
l To use the multi-BBU interconnection feature, operators must purchase the licenses for
this feature.
The number of licenses to be purchased depends on the number of NEs to be
connected to USUs.
The number of licenses for a second-level USU depends on the number of first-
level USUs to be connected to the second-level USU.
The number of licenses for a first-level USU depends on the number of BBUs to be
connected to the first-level USU.
The principles that whether a USU occupies a license are as follows:
n In centralized Cloud BB mode:
A license is occupied by a first-level USU only when both the CI
interconnection cable and the HEI interconnection cable are used. If only the
CI interconnection cable or HEI interconnection cable is used, no license isoccupied.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
44
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
49/89
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
50/89
Feature ID
FeatureName
LicenseControl ItemID
LicenseControlItem
NE SalesUnit
LOFD-
003013
02
IEEE158
8 V2
Clock
Synchro
nization
LT1S00ENSY0
0
Enhanced
Synchronizati
on (FDD)
eNodeB per
eNode
B
LTE TDD eNodeBs in distributed Cloud BB mode
Feature ID
FeatureName
LicenseControl ItemID
LicenseControlItem
NE SalesUnit
TDLOFD-003
01302
IEEE1588 V2
clock
synchron
ization
LT1ST0ESYN00
EnhancedSynchronizati
on (TDD)
eNodeB per eNode
B
Other Requirements
l USUs must be installed to interconnect BBUs.
lThe eNodeB and USU software versions must be compatible with those used in thecurrent version.
6.4.3 Data Preparation and Feature Activation
6.4.3.1 Data Preparation
Data to be prepared is classified into two types:
l Common configuration data for eNodeBs and USUs
The following table describes the parameter that must be set in the NEMO tospecify a Cloud BB ID.
ParameterName
Parameter ID Setting Notes Data Source
Cloud BB
Identifier
NE.CloudBBID Set this parameter
as planned.
Network plan
(negotiation not
required)
The following table describes the parameters that must be set in the ETHCIPORT
MO to configure CI ports.
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
46
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
51/89
ParameterName
Parameter ID Setting Notes Data Source
Subboard Type ETHCIPORT.S
BT
Set this parameter
to
BASE_BOARD(
Base Board).
Network plan
(negotiation not
required)
Port No. ETHCIPORT.P
N
Set this parameter
to 0.
Network plan
(negotiation not
required)
The following table describes the parameters that must be set in the ETHPORT
MO to configure Ethernet ports.
Parameter
Name
Parameter ID Setting Notes Data Source
Subboard Type ETHPORT.SBT Set this parameter
to
ETH_COVERB
OARD(Ethernet
Cover Board).
Network plan
(negotiation not
required)
Port No. ETHPORT.PN l For a BBU, set
this parameter
to 2or 3as
required.
l For a USU, setthis parameter
to a value
ranging from 0
to 119.
Network plan
(negotiation not
required)
The following table describes the parameters that must be set in the ETHTRKMO
to configure Ethernet trunks.
ParameterName
Parameter ID Setting Notes Data Source
Subboard Type ETHTRK.SBT Set this parameter
to
ETH_COVERB
OARD(Ethernet
Cover Board).
Network plan
(negotiation not
required)
Trunk No. ETHTRK.TN Set this parameter
to a unique value
for an Ethernet
trunk in a Cloud
BB network.
Network plan
(negotiation not
required)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
47
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
52/89
The following table describes the parameters that must be set in the ETHTRKLNK
MO to configure the ports in Ethernet trunks.
ParameterName
Parameter ID Setting Notes Data Source
Port No. ETHTRKLNK.P
N
l For a BBU, set
this parameter
to 2or 3as
required.
l For a USU, set
this parameter
to a value
ranging from 0
to 119.
Network plan
(negotiation not
required)
Master Flag ETHTRKLNK.F
LAG
Set this parameter
to YES(Yes)forthe primary port
and NO(No)for
other ports.
Network plan
(negotiation notrequired)
The following table describes the parameters that must be set in the DEVIPMO to
configure device IP addresses.
ParameterName
Parameter ID Setting Notes Data Source
Subboard Type DEVIP.SBT lFor the UMPTin a BBU or a
UEFU in a
USU, set this
parameter to
BASE_BOAR
D(Base
Board).
l For other
boards, set this
parameter to
ETH_COVE
RBOARD(Ethernet Cover
Board).
Network plan
(negotiation not
required)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
48
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
53/89
ParameterName
Parameter ID Setting Notes Data Source
Port Type DEVIP.PT l For the UMPT
in a BBU, set
this parameter
to
ETHCI(Ether
net CI Port).
l For the UCCU
in a BBU, set
this parameter
to
ETH(Etherne
t Port)or
ETHTRK(Et
hernetTrunk).
Network plan
(negotiation not
required)
Port No. DEVIP.PN l For the UMPT
in a BBU, set
this parameter
to 0.
l For the UCCU
in a BBU, set
this parameter
to 2or 3.
Network plan
(negotiation not
required)
IP Address DEVIP.IP Set this parameteras required.
Network plan(negotiation not
required)
The following table describes the parameters that must be set in the
CASCADEPORTMO to configure interconnection ports.
ParameterName
Parameter ID Setting Notes Data Source
Port No. CASCADEPOR
T.PN
l For the UMPT
in a BBU, set
this parameter
to 8.
l For the
LBBPd or
UBBPd, set
this parameter
to 6.
l For a USU, set
this parameter
as required.
Network plan
(negotiation not
required)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
49
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
54/89
ParameterName
Parameter ID Setting Notes Data Source
Switch CASCADEPOR
T.SW
Set this parameter
to ON(On).
Network plan
(negotiation not
required)
The following table describes the parameters that must be set in the IPCLKLINK
MO to configure IP clock links.
Parameter Name
Parameter ID Setting Notes DataSource
Link No. IPCLKLNK.L
N(N/A,LTE FDD
eNodeB)
l For an eNodeB:
When theDEVTYPE
parameter is set to
OC_SLAVE, set theLN
parameter to 0or 1.
When theDEVTYPE
parameter is set to
OC_MASTER, set the
LNparameter to 2.
l For a USU:
When theDEVTYPE
parameter is set to
OC_MASTERor BC, set
theLNparameter to 2.
When theDEVTYPE
parameter is set to
OC_SLAVE, set theLN
parameter to 0or 1.
Network
plan
(negotiation
notrequired)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
50
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
55/89
Parameter Name
Parameter ID Setting Notes DataSource
Device
Type
IPCLKLNK.DE
VTYPE(N/
A,LTE FDD
eNodeB)
l For an eNodeB:
When the eNodeBprovides a clock source
for time synchronization,
set this parameter to
OC_MASTER.
When the eNodeB
receives clock signals, set
this parameter to
OC_SLAVE.
l For a USU:
When the USU provides a
clock source for timesynchronization, set this
parameter to
OC_MASTER.
When the USU forwards
clock signals, set this
parameter to BC.
Network
plan
(negotiation
not
required)
Clock
Net
Mode
IPCLKLNK.CN
M(N/A,LTE
FDD eNodeB)
Set this parameter to
L2_MULTICAST.
Network
plan
(negotiation
not
required)
Profile
Type
IPCLKLNK.PR
OFILETYPE(N/
A,LTE FDD
eNodeB)
Set this parameter to 1588V2. Network
plan
(negotiation
not
required)
The following table describes the parameters that must be set in the TASMMO to
configure the system clock.
ParameterName ParameterID Setting Notes DataSource
Clock
Working
Mode
TASM.MO
DE
Set this parameter to MANUAL. Network
plan
(negotiati
on not
required)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
51
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
56/89
ParameterName
ParameterID
Setting Notes DataSource
Cloud BB
Clock
Reference
Source Flag
TASM.CL
OUDSRC
l For an eNodeB:
When the eNodeB provides aclock source for time
synchronization, set this
parameter to
ENABLE(ENABLE).
When the eNodeB receives
clock signals, set this
parameter to
DISABLE(DISABLE).
l For a USU:
When the USU provides a
clock source for timesynchronization, set this
parameter to
ENABLE(ENABLE).
When the USU forwards
clock signals, set this
parameter to
DISABLE(DISABLE).
Network
plan
(negotiati
on not
required)
Selected
Clock Source
TASM.CL
KSRC
l For an eNodeB:
When the eNodeB provides a
clock source for time
synchronization, set this
parameter to GPS(GPS
Clock)or IPCLK(IP Clock).
When the eNodeB receives
clock signals, set this
parameter to
INTERCLK(Inter Clock).
l For a USU:
When the USU provides a
clock source for time
synchronization, set thisparameter to GPS(GPS
Clock)or IPCLK(IP Clock).
When the USU forwards
clock signals, this parameter
is not required.
Network
plan
(negotiati
on notrequired)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
52
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
57/89
ParameterName
ParameterID
Setting Notes DataSource
Clock
Synchronizati
on Mode
TASM.CL
KSYNCM
ODE
l For an eNodeB, set this
parameter to TIME(TIME).
l For a USU:
When the USU forwards
clock signals, this parameter
is not required.
When the USU provides a
clock source for time
synchronization, set this
parameter to TIME(TIME).
Network
plan
(negotiati
on not
required)
The following table describes the parameters that must be set in the INTERCLKMO to configure the shared clock source.
ParameterName
Parameter ID
Setting Notes DataSource
Interconnectio
n Clock No.
InterClk.
LN
Set this parameter to 0. Network
plan
(negotiati
on not
required)
Priority InterClk.
PRI
l Set this parameter to the priority
of the clock source on an eNodeBreceiving clock signals. The value
ranges from 1 to 4. The default
value is 4, which indicates the
lowest priority.
l If the TASM.MODEparameter is
set to AUTO(Auto), the eNodeB
selects the clock source with the
highest priority.
Network
plan(negotiati
on not
required)
lConfiguration data dedicated to USUs The following table describes the parameter that must be set in the INTERCONNE
MO to specify NE names.
ParameterName
Parameter ID Setting Notes DataSource
Network Element
Name
INTERCONNE.
NENAME
Set this parameter to the
name of an eNodeB
connecting to a USU.
Network
plan
(negotiatio
n not
required)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
53
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
58/89
The following table describes the parameters that must be set in the
GTRANSPARAMO to configure global transmission parameters.
ParameterName
Parameter ID Setting Notes DataSource
Level GTRANSPARA.
LEVEL
Set this parameter to
LEVEL1(LEVEL1)or
LEVEL2(LEVEL2)as
required.
Network
plan
(negotiatio
n not
required)
Network Mode GTRANSPARA.
NETMODE
Set this parameter to
CENTRALIZED(CEN
TRALIZED),
DISTRIBUTED(DIST
RIBUTED), or
HYBRID(HYBRID)asrequired.
Network
plan
(negotiatio
n not
required)
Node ID GTRANSPARA.
NODEID
Set this parameter only
when the first- and
second-level USUs are
connected in centralized
Cloud BB mode.
Otherwise, do not set
this parameter.
For a first-level USU, set
this parameter to a value
ranging from 0 to 11. Fora second-level USU, set
this parameter to a value
ranging from 0 to 5.
Network
plan
(negotiatio
n not
required)
The following table describes the parameters that must be set in the PORTIPMO
to configure port IP addresses.
ParameterName
Parameter ID Setting Notes DataSource
IP Address PORTIP.IP Set this parameter for an
HEI port working in
SCPRI/SRIO mode on
the ULPU in a USU as
required.
Network
plan
(negotiatio
n not
required)
Mask PORTIP.MASK Set this parameter as
required.
Network
plan
(negotiatio
n not
required)
SingleRAN
USU3910-based Multi-BBU Interconnection Feature
Parameter Description 6 Engineering Guidelines
Issue 02 (2015-08-31) Huawei Proprietary and Confidential
Copyright Huawei Technologies Co., Ltd.
54
-
7/25/2019 USU3910 Based Multi BBU Interconnection(SRAN10.1_02)
59/89
The following table describes the parameter that must be set in the PORTMODE
MO to specify the working mode for ports.
ParameterName
Parameter ID Setting Notes DataSource
Port Mode PORTMODE.P
M
l In centralized Cloud
BB mode, set this
parameter to SCPRI/
SRIO(SCPRI/
SRIO).
l In distributed Cloud
BB mode:
For an HEI port
connecting to an
eNodeB, set this
parameter to4*10GE(4*10GE
).
For an HEI port
connecting to the
second-level
USU, set this
parameter to
1*40GE(1*40GE
).
Network
plan
(negotiatio
n not
required)
6.4.3.2 Activation
Using the CME to Perform Batch Configuration
Enter the values of the parameters listed in Table 6-2and Table 6-3in a summary data file,
which also contains other data for