vapor and combined power cycles - chainarongchainarong.me.engr.tu.ac.th/documents/me331...
TRANSCRIPT
![Page 1: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/1.jpg)
1
Vapor and Combined Power Cycles
![Page 2: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/2.jpg)
2
A gas power cycle considers air as the working fluid → single phaseA vapor power cycle considers steam as the working fluid → might be two phases
The use of steam as working fluid
• Low cost• Availability• High enthalpy of vaporization
Carnot cycle• Give maximum thermal efficiency• But not be suitable to use for analyzing
the efficiency of vapor power cycle
Carnot Vapor Cycle
Vapor power cycles
![Page 3: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/3.jpg)
3
• Analyze vapor power cycles in which the working fluid is alternately vaporized and condensed.
• Analyze power generation coupled with process heating, called cogeneration.
• Investigate methods to modify the basic Rankine vapor power cycle to increase the cycle thermal efficiency.
• Analyze the reheat and regenerative vapor power cycles.• Analyze power cycles that consist of two separate cycles known as
combined cycles and binary cycles.
Objectives
![Page 4: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/4.jpg)
4
Carnot vapor cycleThe working fluid, steam (water), undergoes a thermodynamic cycle from 1-2-3-4-1.
1
2
4
30.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.00
100
200
300
400
500
600
700700
s [kJ/kg-K]
T [C
]
6000 kPa
100 kPa
Carnot Vapor Cycle Using Steam
1
2 3
4
, 1 1net out Lth Carnot
in in H
W Q TQ Q T
η = = − = −
•The larger the TH the larger the ηth, Carnot•The smaller the TL the larger the ηth, Carnot
• To increase the thermal efficiency in any power cycle, we try to increase the maximum temperature at which heat is added.
![Page 5: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/5.jpg)
5
• Pumping process 1-2 requires the pumping of a mixture of saturated liquid and saturated vapor at state 1 and the delivery of a saturated liquid at state 2.
Reasons why the Carnot cycle is not used!
• To superheat the steam to take advantage of a higher temperature, elaborate controls are required to keep TH constant while the steam expands and does work.
0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.00
100
200
300
400
500
600
700700
s [kJ/kg-K]
T [C
]
6000 kPa
100 kPa
Carnot Vapor Cycle Using Steam
1
2 3
4 1
2
4
3
![Page 6: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/6.jpg)
6
Rankine Cycle
0 2 4 6 8 10 12120
100
200
300
400
500
s [kJ/kg-K]
T [C
]
6000 kPa
10 kPa
Rankine Vapor Power Cycle
1
2
3
4
Ideal Rankine Cycle Processes Process Description 1-2 Isentropic compression in pump 2-3 Constant pressure heat addition in boiler 3-4 Isentropic expansion in turbine 4-1 Constant pressure heat rejection in condenser
•The simple Rankine cycle continues the condensation process 4-1 until the saturated liquid line is reached.
0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.00
100
200
300
400
500
600
700700
s [kJ/kg-K]
T [C
]
6000 kPa
100 kPa
Carnot Vapor Cycle Using Steam
1
2 3
4
![Page 7: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/7.jpg)
7
Use the power system and T-s diagram.P2 = P3 = 6 MPa = 6000 kPaT3 = 350oCP1 = P4 = 10 kPa
Example
0 2 4 6 8 10 12120
100
200
300
400
500
s [kJ/kg-K]
T [C
]
6000 kPa
10 kPa
Rankine Vapor Power Cycle
1
2
3
4
Compute the thermal efficiency of an ideal Rankine cycle for which steam leaves the boiler as superheated vapor at 6 MPa, 350oC, and is condensed at 10 kPa.
![Page 8: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/8.jpg)
8
- Assume steady-flow- Neglecting ΔPE & ΔKE- Assume adiabatic and reversible processes
( )
m m mm h W m h
W m h hpump
pump
1 2
1 1 2 2
2 1
= =
+ =
= −
Since the pumping process involves an incompressible liquid, state 2 is in the compressed liquid region
dh = T ds + v dP
Since the ideal pumping process 1-2 is isentropic, ds = 0.
Pump
1
2
4
3
Recall the property relation:
0 2 4 6 8 10 12120
100
200
300
400
500
s [kJ/kg-K]
T [C
]
6000 kPa
10 kPa
Rankine Vapor Power Cycle
1
2
3
4
![Page 9: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/9.jpg)
9
The incompressible liquid assumption allows
v v consth h v P P≅ =− ≅ −
1
2 1 1 2 1
.( )
The pump work :
( ) ( )
( )
W m h h mv P P
wW
mv P P
pump
pumppump
= − ≅ −
= = −
2 1 1 2 1
1 2 1
Use the steam tables
11
3
1
191.8110
.0.00101
f
f
kJh hkgP kPa
Sat liquid mv vkg
⎧ = =⎪= ⎫⎪⎬⎨⎭⎪ = =⎪⎩
1 2 1
3
3
( )
0.00101 (6000 10) 6.05
pumpw v P P
m kJ kJkPakg m kPa kg
= −
= − =
0 2 4 6 8 10 12120
100
200
300
400
500
s [kJ/kg-K]
T [C
]
6000 kPa
10 kPa
Rankine Vapor Power Cycle
1
2
3
4
![Page 10: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/10.jpg)
10
h2 is found from 2 1
6.05 191.81 197.86
pumph w h
kJ kJ kJkg kg kg
= +
= + =
![Page 11: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/11.jpg)
11
• To find the heat supplied in the boiler, assume • Conservation of mass and energy for steady flow• Neglect ΔPE & ΔKE • No work is done on the steam in the boiler
( )
m m mm h Q m h
Q m h hin
in
2 3
2 2 3 3
3 2
= =
+ =
= −• Find the properties at state 3 from the
superheated tables3
3
33
3043.96000
350 6.3357o
kJhP kPa kg
kJT C skg K
⎧ =⎪= ⎫⎪⎬⎨
= ⎭⎪ =⎪ ⋅⎩
Boiler
• The heat transfer per unit mass :
3 2in
inQq h hm
= = − (3043.9 197.86) 2845.1kJ kJkg kg
= − =
![Page 12: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/12.jpg)
12
To find turbine work assume- Conservation of mass and energy for steady flow.- The process is adiabatic and reversible - Neglect ΔPE & ΔKE
( )
m m mm h W m hW m h h
turb
turb
3 4
3 3 4 4
3 4
= =
= +
= −
Find the properties at state 4 from the steam tables by noting s4 = s3 = 6.3357 kJ/kg-K
4 10 : 0.6492 ; 8.1488f gkJ kJat P kPa s s
kg K kg K= = =
⋅ ⋅
Turbine
44
6.3357 0.6492 0.7587.4996
f
fg
s sx
s− −
= = =
0 2 4 6 8 10 12120
100
200
300
400
500
s [kJ/kg-K]
T [C
]
6000 kPa
10 kPa
Rankine Vapor Power Cycle
1
2
3
4
4 4f fgs s x s= +
![Page 13: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/13.jpg)
13
4 4
191.81 0.758(2392.1)
2005.0
f fgh h x h
kJ kJkg kgkJkg
= +
= +
=
T he turbine work per unit mass
3 4turbw h h= −
The net work done by the cycle :
net turb pumpw w w= −
0 2 4 6 8 10 12120
100
200
300
400
500
s [kJ/kg-K]
T [C
]
6000 kPa
10 kPa
Rankine Vapor Power Cycle
1
2
3
4
(1038.9 6.05)
1032.8
kJkg
kJkg
= −
=
(3043.9 2005.0)
1038.9
kJkg
kJkg
= −
=
![Page 14: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/14.jpg)
14
1032.8
2845.1
0.363 36.3%
netth
in
kJw kg
kJqkg
or
η = =
=
The thermal efficiency
1
2
4
3
0 2 4 6 8 10 12120
100
200
300
400
500
s [kJ/kg-K]
T [C
]
6000 kPa
10 kPa
Rankine Vapor Power Cycle
1
2
3
4
![Page 15: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/15.jpg)
15
Previous lecture
Ideal Rankine cycle
Analyzing the efficiency of components
Today lecture
Deviation of actual vapor cycles
Way to improve the Rankine cycle
Ideal Rankine cycle with reheat
Ideal Rankine cycle with regeneration
Isentropic efficiency
Cogeneration
Next lecture
![Page 16: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/16.jpg)
16
Deviation of actual vapor power cycles from idealized cycles
Fluid friction → pressure drops in boiler, condenser, and piping
Irreversibility: heat loss from steam to surroundings
2 1
2 1
s sP
a a
w h hw h h
−= =
−η 3 4
3 4
a aT
s s
w h hw h h
−= =
−η
Isentropic efficiency
![Page 17: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/17.jpg)
17
A steam power plant operates on the cycle shown in Fig. If the isentropic efficiency of turbine is 87 percent and the isentropic efficiency of the pump is 85 percent, determine (a) the thermal efficiency of the cycle and (b) the net power output of the plant for a mass flow rate of 15 kg/s
Example
![Page 18: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/18.jpg)
18
Ways to improve the simple Rankine cycle efficiency
Increase the average temperature at which heat is transferred to the working fluid in the boiler, or decrease the average temperature at which heat is rejected from the working fluid in the condenser.
![Page 19: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/19.jpg)
19
• Lower condenser pressure- Less energy is lost to surroundings.
Ways to improve the simple Rankine cycle efficiency
- Min. temp is limited by cooling temperature- Lower temperature gives lower pressure, and this might cause the
problem of air leakage into condenser.
- Moisture is increased at turbine exit.
- Too much moisture gives lower turbine efficiency and erosion ofturbine blade.
![Page 20: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/20.jpg)
20
Superheat the vapor (without increasing the boiler pressure)Average temperature is higher during heat addition.
Ways to improve the simple Rankine cycle efficiency
- Moisture is reduced at turbine exit.- Max. temp is limited by metallurgical property
![Page 21: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/21.jpg)
21
• Increase boiler pressure (for fixed maximum temperature)
Ways to improve the simple Rankine cycle efficiency
- Moisture is increased at turbine exit (Side effect and improved by reheating).
- Availability of steam is higher at higher pressures.
![Page 22: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/22.jpg)
22
Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350 OC and is condensed in the condenser at a pressure of 10 kPa. Determine (a) the thermal efficiency of this power plant, (b) the thermal efficiency if steam is superheated to 600OC instead of 350OC, and (c) the thermal efficiency if the boiler pressure is raised to 15 MPa while the turbine inlet temperature is maintained at 600OC.
Example
(a) (b) (c)
![Page 23: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/23.jpg)
23
1net in out inth
in in out
w q q qq q q
−η = = = −
3 2inq h h= −
4 1outq h h= −
![Page 24: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/24.jpg)
24
3376.234882921.3qin
1923.52188.51944.3qout
43%37.3%33.4%ηth
0.8040.9150.8128x
15 MPa3 MPa3 MPaPmax
600oC600 oC350 oCTmax
(c)(b)(a)
![Page 25: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/25.jpg)
25
As the boiler pressure is increased in the simple Rankine cycle, not only does the thermal efficiency increase, but also the turbine exit moisture increases.
Ideal Reheat Rankine Cycle
1. Superheat the steam to very high temperature before it enters the turbine (limited by metallurgical property)
2. Expand the steam in the turbine in two states, and reheat it in between.
![Page 26: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/26.jpg)
26
( ) ( )3 2 5 4in primary reheatq q q h h h h= + = − + −
( ) ( ),1 ,2 3 4 5 6turb turb turbw w w h h h h= + = − + −
Ideal Reheat Rankine Cycle
![Page 27: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/27.jpg)
27
Ideal Reheat Rankine Cycle- The average temperature during the reheat process can be increased
by increasing the number of expansion and reheat stages. - As the number of stages is increased, the expansion and reheat
processes approach an isothermal process at the max. temp.- In theory, efficiency from the second reheat is about half of that from a
single reheat. And if the turbine inlet pressure is not high enough, double reheat would result in superheated exhaust (increase the average temperature for heat rejection) → super critical pressure P > 22.06 MPa
![Page 28: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/28.jpg)
28
Component Process First Law Result Boiler Const. P qin = (h3 - h2) + (h5 - h4) Turbine Isentropic wout = (h3 - h4) + (h5 - h6) Condenser Const. P qout = (h6 - h1) Pump Isentropic win = (h2 - h1) = v1(P2 - P1)
The thermal efficiency is given by
η thnet
in
wqh h h h h h
h h h hh h
h h h h
=
=
= −−
( - ) + ( - ) - ( - )( - ) + ( - )
( - ) + ( - )
3 4 5 6 2 1
3 2 5 4
6 1
3 2 5 4
1
Rankine Cycle with Reheat
![Page 29: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/29.jpg)
29
Consider a steam power plant operating on the ideal reheat Rankine cycle. Steam enters the high-pressure turbine at 15 MPa and 600OC and is condensed in the condenser at a pressure of 10 kPa. If the moisture content of the steam at the exit of the low-pressure turbine is not to exceed 10.4 percent, determine (a) the pressure at which the steam should be reheated and (b) the thermal efficiency of the cycle. Assume the steam is reheated to the inlet temperature of the high-pressure turbine.
Example
![Page 30: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/30.jpg)
30
![Page 31: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/31.jpg)
31
![Page 32: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/32.jpg)
32
![Page 33: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/33.jpg)
33
![Page 34: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/34.jpg)
34
![Page 35: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/35.jpg)
35
Compare the thermal efficiency and turbine-exit quality at the condenser pressure for a simple Rankine cycle and the reheat cycle when the boiler pressure is 4 MPa, the boiler exit temperature is 400oC, and the condenser pressure is 10 kPa. The reheat takes place at 0.4 MPa and the steam leaves the reheater at 400oC.
ηth xturb exitNo Reheat 35.3% 0.8159 With Reheat 35.9% 0.9664
Assignment 5
![Page 36: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/36.jpg)
36
• To improve the cycle thermal efficiency, the average temperature at which heat is added must be increased.
Ideal Regenerative Rankine Cycle
• Allow the steam leaving the boiler to expand the steam in the turbine to an intermediate pressure.
- Some of steam from turbine is sent to a regenerative heater to preheat the condensate before entering the boiler.→ increase feeding water (boiler) temp.
- However, this reduces the mass of steam expanding in the lower-pressure stages of the turbine, and, thus, the total work done by the turbine. The work that is done is done more efficiently.
![Page 37: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/37.jpg)
37
The preheating of the condensate is done in a combination of open and closed heaters.
- In the open feed water heater, the extracted steam and the condensate are physically mixed.
- In the closed feed water heater, the extracted steam and the condensate are not mixed.
Open feed water heater Closed feed water heater
![Page 38: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/38.jpg)
38
Cycle with an open feedwater heater
5 4inq h h= −
( )( )7 11outq y h h= − −
( ) ( )( ), 5 6 6 71turb outw h h y h h= − + − −
( ), ,1, ,2,1pump in pump in pump inw y w w= − +
6 5/y m m=
( ),1, 1 2 1pump inw v P P= −
( ),2, 3 4 3pump inw v P P= −
![Page 39: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/39.jpg)
39
y m m= /6 5Let be the fraction of mass extracted from the turbine for the feedwater heater.
( )
m mm m m m
m m m m y
in out=+ = =
= − = −6 2 3 5
2 5 6 5 1
Conservation of energy for the open feedwater heater:
( )
E Em h m h m h
ym h y m h m h
y h hh h
in out=+ =
+ − =
=−−
6 6 2 2 3 3
5 6 5 2 5 3
3 2
6 2
1
![Page 40: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/40.jpg)
40
Cycle with a closed feedwater heater with pump to boiler pressure
![Page 41: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/41.jpg)
41
Consider a steam power plant operating on the ideal regenerative Rankine cycle with one open feed water heater. Steam enters the turbine at 15 MPaand 600OC and is condensed in the condenser at a pressure of 10 kPa. Some steam leaves the turbine at a pressure of 1.2 MPa and enters the open feed water heater. Determine the fraction of steam extracted from the turbine and the thermal efficiency of the cycle.
Example
![Page 42: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/42.jpg)
42
![Page 43: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/43.jpg)
43
![Page 44: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/44.jpg)
44
![Page 45: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/45.jpg)
45
![Page 46: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/46.jpg)
46%
![Page 47: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/47.jpg)
47
A steam power plant operates on an ideal regenerative Rankine cycle. Steam enters the turbine at 6 MPa 450OC and is condensed in the condenser at 20 kPa. Steam is extracted from the turbine at 0.4 MPa to heat the feedwater in a closed feedwater heater. Water leaves the heater at the condensation temperature of the extracted steam and that the extracted steam leaves the heater as a saturated liquid and is pumped to the line carrying the feedwater. Determine (a) the net work output per kilogram of steam flowing throught the boiler and (b) the thermal efficiency of the cycle.
Example: Closed feedwater heater
![Page 48: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/48.jpg)
48
![Page 49: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/49.jpg)
49
![Page 50: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/50.jpg)
50
![Page 51: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/51.jpg)
51
![Page 52: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/52.jpg)
52
![Page 53: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/53.jpg)
53
• Piping losses--frictional effects reduce the available energy content of the steam.
•Turbine losses--turbine isentropic (or adiabatic) efficiency.
4a4s
3
s
T P3
P4
η turbactual
isentropic
a
s
ww
h hh h
= =−−
3 4
3 4
The actual enthalpy at the turbine exit (needed for the energy analysis of the next component) is
h h h ha turb s4 3 3 4= − −η ( )
Deviation from Actual Cycles
![Page 54: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/54.jpg)
54
•Pump losses--pump isentropic (or adiabatic) efficiency.
2a2s
1
s
T P2
P1
η pumpisentropic
actual
s
a
ww
h hh h
= =−−
2 1
2 1
The actual enthalpy at the pump exit (needed for the energy analysis of the next component) is
h h h hapump
s2 1 2 11
= + −η
( )
•Condenser losses--relatively small losses that result from cooling the condensate below the saturation temperature in the condenser.
![Page 55: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/55.jpg)
55
Second law analysis of vapor power cycles- Ideal Carnot cycle is a totally reversible- Ideal Rankine cycles may involve irreversibilities external to the system,
e.g. heat transfer through a finite temperature difference- Second law analysis of these cycles is used to reveal where the largest
irreversibilities occur and what their magnitude are.
( )0 0destruction gen out inX T S T S S= = −
0, ,
out in
out inb out b in
Q QT ms msT T
⎛ ⎞= + − −⎜ ⎟⎜ ⎟
⎝ ⎠∑ ∑
0 0, ,
out indestruction gen e i
b out b in
q qx T s T s sT T
⎛ ⎞= = − + −⎜ ⎟⎜ ⎟
⎝ ⎠
Or on a unit mass basis for a one-inlet, one-exit, steady flow device
![Page 56: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/56.jpg)
56
Second law analysis of vapor power cycles- Exergy destruction associated with a cycle depends on the magnitude of
the heat transfer with the high- and low- temperature reservoirs.
0, ,
out indestruction
b out b in
q qx TT T
⎛ ⎞= −⎜ ⎟⎜ ⎟
⎝ ⎠∑ ∑
For a cycle that involves heat transfer only with a source at TH and a sink at TL, the exergy destruction are
0out in
destructionL H
q qx TT T
⎛ ⎞= −⎜ ⎟
⎝ ⎠Exergy of a fluid stream φ at any states is
( ) ( )2
0 0 0 2Vh h T s s gzϕ = − − − + +
![Page 57: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/57.jpg)
57
ExampleDetermine the exergy destruction associated with the Rankine cycle (all four processes as well as the cycle), assuming that heat is transferred to the steam in a furnace at 1600 K and heat is rejected to a cooling medium at 290 K and 100 kPa. Also, determine the exergy of the steam leaving the turbine
100 kPa
100 kPa
![Page 58: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/58.jpg)
58
![Page 59: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/59.jpg)
59
![Page 60: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/60.jpg)
60
![Page 61: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/61.jpg)
61
CogenerationCogeneration is the production of more than one useful form of energy (such as process heat and electric power) from the same energy source
Boiler Processheater
pQ
Boiler
Process heater
100kW
10kW
Turbine
pump
pump
inQ120kW
A simple process-heating plant An ideal cogeneration plant
![Page 62: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/62.jpg)
62
Cogeneration
Steam turbine
Process heat
Chemical, pulp and paper, oil production
5 ~ 7 atm, 150 – 200OC
Cogeneration is the production of more than one useful form of energy (such as process heat and electric power) from the same energy source
Heat transfer to the steam in boiler
Producing EE
![Page 63: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/63.jpg)
63
Cogeneration
![Page 64: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/64.jpg)
64
Net work output + Process heat deliveredTotal heat inputuε =
net p
in
W QQ+
=
1 outu
in
ε = −
Utilization factor, εu
Waste heat rejection from turbine transfers to the steam in boiler and is utilized as either process heat or electric power.
Utilization factor, εu
outQ = presents the heat rejected in the condenser.
εu = 100% when no any heat losses in system
![Page 65: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/65.jpg)
65
Steam enters the turbine at 7 MPa and 500OC. Some steam is extracted from the turbine at 500 kPa for process heating. The remaining steam continues to expand to 5 kPa. Steam is then condensed at constant pressure and pumped to the boiler pressure of 7 MPa. At times of high demand for process heat, some steam leaving the boiler is throttled to 500 kPa and is routed to the process heater. The extraction fraction are adjusted so that steam leaves the process heater as a saturated liquid at 500 kPa. It is subsequently pumped to 7 MPa. The mass flow rate of steam through the boiler is 15 kg/s. Disregarding any pressure drops and heat losses in the piping and assuming the turbine and the pump to be isentropic, determine (a) the maximum rate at which process heat can be supplied, (b) the power produced and the utilization factor when no process heat is supplied, and (c) the rate of process heat supply when 10 percent of the steam is extracted before it enters the turbine and 70 percent of the steam is extracted from the turbine at 500 kPafor process heating.
Example
![Page 66: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/66.jpg)
66
![Page 67: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/67.jpg)
67
![Page 68: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/68.jpg)
68
![Page 69: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/69.jpg)
69
![Page 70: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/70.jpg)
70
![Page 71: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/71.jpg)
71
![Page 72: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/72.jpg)
72
![Page 73: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/73.jpg)
73
![Page 74: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/74.jpg)
74
![Page 75: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/75.jpg)
75
A textile plane require 4 kg/s of saturated steam at 2 MPa, which is extracted from the turbine of a cogeneration plant. Steam enters the turbine at 8 MPaand 500OC at a rate of 11 kg/s and leaves at 20 kPa. The extracted steam leaves the process heater as a saturated liquid and mixes with the feed water at constant pressure. The mixture is pumped to the boiler pressure. Assuming and isentropic efficiency of 88 percent for both the turbine and the pumps, determine (a) the rate of process heat supply, (b) the net power output, and (c) the utilization factor of the plant.
Example
![Page 76: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/76.jpg)
76
![Page 77: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/77.jpg)
77
![Page 78: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/78.jpg)
78
![Page 79: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/79.jpg)
79
![Page 80: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/80.jpg)
80
![Page 81: Vapor and Combined Power Cycles - Chainarongchainarong.me.engr.tu.ac.th/documents/ME331 Thermodynamics II/ME... · A vapor power cycle considers steam as the working fluid →might](https://reader031.vdocuments.net/reader031/viewer/2022030519/5ac506c47f8b9a57528d6dc5/html5/thumbnails/81.jpg)
81