vdsl2 pots splitters and microfilters

www.AFLglobal.com1

4 kH

zPO

TS

0.025

0.138

3.75

DS1 US1 DS2 US2 DS3 US3

US0

5.2 8.5 12 23 30 MHz

VDSL2 POTS Splitters and Microfilters

Introduction

The purpose of this paper is to discuss the characteristics of splitters and microfilters for VDSL2 applications. Both CPE con-figurations are simplified into an equivalent loop representation in order to more easily compare the characteristics that will most significantly affect VDSL2 performance, specifically impedance changes due to the presence of bridge taps and loadingof the LINE in the DSL frequency band.

Splitters and Microfilters—Overview

In typical DSL deployments, Voice and DSL services are provide over the same line of twisted-pair copper wires. The copper wires carry signals with frequencies up to 30 MHz (VDSL2), enabling customer data rates of more than 100 MBps. The figure below illustrates an example of a VDSL2 band-plan:

Figure 1: VDSL2 Band Plan Distribution (US Upstream, DS Downstream)

As seen above, the line at the customer’s premises contains voice signals (POTS- lower frequency range up to 4 kHz) for the telephone as well as data signals (higher frequency range 25 kHz – 30 MHz) for DSL services. Signals intended for DSL service disrupt the service of the voice calls. More importantly, phone transient events disrupt DSL service making it is essential to isolate the low frequency POTS signal from DSL signals.

At the Customer Premise, isolation between POTS signals and DSL signals is most commonly achieved by installing either a single CPE splitter or multiple microfilters (also known as in-line filters).

Testing and Verification provided by Comtest Networks

Fiber Inside Plant

www.AFLglobal.com or (800)235-3423 2


Microfilters

A microfilter is a Low-Pass Filter (LPF) that isolates the low frequency signals on the line from the high frequency (DSL) signals and prevents interference between the two. Microfilters have Line and POTS ports and are typically installed ‘in-line’ with telephones, fax machines and/or answering machines, and can be easily installed by the customer.

Figure 2 shows a typical household loop configuration with microfilters. The loop is defined by main segment L1 from the central office to the Line Port at the customer premises, L5 segment from the Line Port at the home to the modem, and additional line segments (bridge taps) L2, L3, and L4 which connect the line port with 3 in-line filters. (Note: These segments may represent one of three con-nections: 1) an in-line filter terminated with a telephonic device; 2) an unterminated in line-filter; or, 3) unterminated telephone wiring in the home.). It should be noted that in-line filters are connected in parallel with the line to the modem; a parallel connection with the line has a very high possibility of significantly changing the impedance of the line.

L5

L3L2

L4

L1

Simplified loop of in-line filter configuration

Typical in-line filter configuration

In-Line Filter In-Line Filter In-Line Filter

To CO

L1

L2 L3 L4

L5

DSL Modem/Router

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

Figure 2: Typical loop configuration with multiple in-line filter installation


Fiber Inside Plant



CPE Splitter

A CPE splitter has 3 connections: Line, DSL and POTS. It provides low pass filtering between the Line Port and POTS port and a HPF (high pass filter) or all pass filter between Line and DSL ports.

A typical Loop configuration of CPE splitter installation is shown in Figure 3. In this situa-tion, the loop for DSL signal is defined by main segment L1 between the central office and the Line Port at the home, and short segment L5 between Line Port and modem. It should be noted that segments L2, L3, L4 do not represent bridge taps to L1 and L5 because they are isolated by the CPE splitter.

Figure 3: Typical loop configuration in a CPE splitter installation

To CO

L1

Line PortPhone Port


L2 L3 L4

L5

DSL Modem/Router

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

DSL Modem Port

AFL ADSL2/VDSL2 Splitter


Fiber Inside Plant



CPE Splitter vs. In-Line Filters

Comparing the installation configurations of a CPE Splitter (Figure 3) and multiple in-line filters (Figure 2), two main differences are noticed:

1. A multiple In-Line filter installation has an equivalent loop with bridge taps, whereas a CPE Splitter installation has an equivalent straight line loop that eliminates bridge taps within the home.

2. Multiple In-Line filters are connected in parallel with line, while only one CPE splitter is connected to the line; therefore the resultant loading effect on the line is greater with in-line filters than with a CPE splitter.

Bridge (Bridged) Tap

A bridge tap is an unterminated branch in a cable, or any branch on a pair that is not a direct connection between the Line and the subscriber. For the purpose of this paper, we will refer to any ‘T’ connection in the copper pairs as a bridge tap, be it unterminated or terminated (with microfilter and/or telephone equipment).

Any signal transmitted on the main copper pair will also travel down the bridge tap. Open end of the bridge tap (or high impedance when filter is installed) will result of the signal being reflected back towards the main copper pair. In the voice band this reflection will result in echo; in the DSL band it will lower attainable data rates.

In the case of longer bridge taps (20- 40 ft) very drastic changes in data rates will occur due to significant changes in insertion loss and imped-ance. Impedance comparison for the two installation options is shown in Figure 4. Ideal input impedance to the modem is 100 Ohms.

Figure 4: Difference of impedance to the modem for loops with in-line filters with in line filters vs CPE splitter with configuration found in Appendix C

0

200

400

600

800

1000

1200

1400

frequ

ency

[kH

z]

3,00

0

6,00

0

9,00

0

12,0

00

15,0

00

18,0

00

21,0

00

24,0

00

27,0

00

Impe

danc

e [O

hms

]

Modulus of impedance seen by modem for configuration H.1

Modulus of impedance seen by modem for configuration A and B


Fiber Inside Plant



Calculations show that with an in-line filter configuration, bride tap segments of just 3 ft in length can change the impedance seen by the modem more than 50%. This change in impedance will result in high reflection and a smaller amount of power transferred to the modem; results will be significantly decreased VDSL2 data rates. Data rates will not be similarly affected with a CPE splitter due to the fact that theCPE splitter eliminates bridge taps, separating DSL and POTS at the input of home network.

In a configuration using in-line filters such as shown in the diagram below. A bridge tap of 40 ft would create notches (highest loss of the signal) around 4 MHz, 12 MHz, 20 MHz and 29 MHz. This would lead to downstream and/or upstream degradation depending upon what bands are impacted by the notches.

Figure 5: Insertion loss notches corresponding with a 40 foot bridge tap

In-Line Filter In-Line Filter

To Telco

1000 feet

40 fe

et

DSL Modem/Router

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

-600

-40

-20

Frequency [Hz]

0

5⋅106 1⋅107 1.5⋅107 2⋅107 2.5⋅107 3⋅107

Inse

rtio

n Lo

ss [d

B]


Fiber Inside Plant



Data Rate Comparison between Configurations using CPE Splitter vs. In-Line Microfilter

Using a 2000 foot loop from the Telco Office to the Customer Premise:

• In-linefilterconfigurationwitha3 foot bridge TAP between modem and phone line in-line filter as shown below. Measured 25% degradation in downstream data rate compared to configuration using a CPE Splitter.

• In-linefilterconfigurationwitha20 foot bridge TAP between modem and phone line in-line filter as shown below. Measured 45% degradation in downstream data rate compared to configuration using a CPE Splitter.


To Telco

2000 feet

3 fe

et

DSL Modem/Router

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


To Telco

2000 feet

20 fe

et

DSL Modem/Router

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


Fiber Inside Plant



Measured Data Rates using Typical Home Wiring Configurations

The following tables compare measured VDSL2 training rates (17a profile) with CPE splitters and various in-line filter configurations. Refer to Appendices A, B and C for diagrams of the in-line filter installations.

AFL ADSL2/VDSL2 SPLITTER ADSL2/VDSL2 splitter placed at beginning of chain. Chain extends from POTS port of ADSL2/VDSL2. DSL Modem is home run from DSL port.

CONFIG A Daisy chain in-line filters 20 ft apart. Last jack has wall mount DSL filter with modem.

CONFIG B Daisy chain in-line filters 20 ft apart. First jack of chain has wall mount DSL filter with modem.

CONFIG C Daisy chain of POTS jacks 20 ft apart. First jack of chain has wall mount DSL filter with modem.

CONFIG D Daisy chain in-line filters 20 ft apart. Fourth jack of chain has wall mount DSL filter with modem.

* See Appendix A Daisy Chain Configuration for details on Configurations

VDSL2 Data Rates (AFL Splitter versus various In-Line Filter Daisy Chain Configurations)

DSDS

DS

DS DSDS

US USUS

USUS US

0

10

20

30

40

50

60

70

80

90

100

Baseline AFL ADSL2/VDSL2 Splitter Microfilter Config A Microfilter Config B Microfilter Config C Microfilter Config D

Mbi

ts


Fiber Inside Plant


VDSL2 Data Rates (AFL Splitter versus In-Line Star configuration of various lengths with length to Filter of 20 ft)

DSDS

DS DS DSUS USUS US US

0

10

20

30

40

50

60

70

80

90

100

Baseline AFL ADSL2/VDSL2 Splitter Microfilter Config F.1 Microfilter Config F.2 Microfilter Config F.3

Mb

its


DSDS

DSDS DSSUSU

US US US

0

10

20

30

40

50

60

70

80

90

100

Baseline AFL ADSL2/VDSL2 Splitter Microfilter Config H.1 Microfilter Config H.2 Microfilter Config H.3

Mb

its


AFL ADSL2/VDSL2 SPLITTER NID-01V splitter placed at beginning of star TAP home run configuration. TAPs extend from POTS port of NID-01V. DSL modem is home run from DSL port.

CONFIG F 5 TAP home run configuration with in-line filters on each end. 20 ft length taps.

* See Appendix B Star—20 foot phone lines for details on Configurations


DSDS

DS DS DSUS USUS US US

0

10

20

30

40

50

60

70

80

90

100

Baseline AFL ADSL2/VDSL2 Splitter Microfilter Config F.1 Microfilter Config F.2 Microfilter Config F.3

Mb

its


DSDS

DSDS DSSUSU

US US US

0

10

20

30

40

50

60

70

80

90

100

Baseline AFL ADSL2/VDSL2 Splitter Microfilter Config H.1 Microfilter Config H.2 Microfilter Config H.3

Mb

its

AFL ADSL2/VDSL2 SPLITTER ADSL2/VDSL2 splitter placed at beginning of star TAP home run configuration. TAPs extend from POTS port of NID-01V. DSL modem is home run from DSL port.

CONFIG H 5 TAP home run configuration with in-line filters on each end. 40 ft length taps.

* See Appendix C Star—40 foot phone lines for details on Configurations


Fiber Inside Plant


VDSL2 POTS Splitters and MicrofiltersAppendix A—Daisy Chain Configuration

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

DSL Modem/Router

3 ft

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

20 ft 20 ft 20 ft 20 ft

Wall MountDSL Filter

DSL Modem/Router

In-Line Filter In-Line Filter In-Line Filter In-Line Filter

AFL NID

To CO

2000 ft


DSL Modem/Router

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

20 ft 20 ft 20 ft 20 ft

In-Line Filter In-Line Filter In-Line Filter In-Line Filter

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

20 ft 20 ft 20 ft 20 ft

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

20 ft 20 ft 20 ft


20 ft

In-Line Filter

AFL NID

To CO

2000 ft

Phone Port

3 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

DSL Modem Port

DSL Modem/Router

20 ft 20 ft 20 ft 20 ft 20 ft

AFL NID

Baseline AFL Splitter

Config A Config B

Config C Config D


Fiber Inside Plant


VDSL2 POTS Splitters and MicrofiltersAppendix B Star—20-foot Phone Lines

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

DSL Modem/Router

3 ft

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

20 ft

20 ft

20 ft

20 ft

20 ft

In-Line Filter

In-Line Filter

In-Line Filter

In-Line Filter

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

20 ft

20 ft

20 ft

20 ft

3 ft

In-Line Filter

In-Line Filter

In-Line Filter

In-Line Filter

AFLNID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt 20 ft

20 ft

20 ft

20 ft


DSL Modem/Router

3 ft

AFLNID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

20 ft

20 ft

3 ft

In-Line Filter

In-Line Filter

20 ft

20 ft

In-Line Filter

In-Line Filter

Phone Port

DSL Modem Port

AFL NID


Config F.1 Config F.2

Config F.3


Fiber Inside Plant


VDSL2 POTS Splitters and MicrofiltersAppendix C Star—40-foot Phone Lines

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt

DSL Modem/Router

3 ft

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

40 ft

40 ft

40 ft

40 ft

40 ft

In-Line Filter

In-Line Filter

In-Line Filter

In-Line Filter

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

40 ft

40 ft

40 ft

40 ft

3 ft

In-Line Filter

In-Line Filter

In-Line Filter

In-Line Filter

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt 40 ft

40 ft

40 ft

40 ft


DSL Modem/Router

3 ft

AFL NID

To CO

2000 ft

Cust

omer

Pre

mis

e(In

side

Wir

ing)

Dem

arca

tion

Poi

nt


DSL Modem/Router

40 ft

40 ft

3 ft

In-Line Filter

In-Line Filter

40 ft

40 ft

In-Line Filter

In-Line Filter

Phone Port

DSL Modem Port

AFL NID


Config H.1 Config H.2

Config H.3


vdsl2 pots splitters and microfilters

Documents