velocity

velocity standard 07V-S-07Chic and robust - a highly-structural portable 10’x10’ exhibit that emphasizes your identity and message seamlessly with a combinaton of fabric graphics, rigid accents and accessories.

dimensions:Hardware Graphic

Assembled unit: 111.5”(w) x 99.375”(h) x 47.5”(d) approx.2832.1mm(w) x 2524mm(h) x 1206.5mm(d)

Counter:39.37”(w) x 40.5”(h) x 15.2”(d) approx.999mm(w) x 1028.7mm(h) x 386.08mm(d)Counter internal dimensions:36.3”(w) x 39.37”(h) x 13.8”(d) approx.922mm(w) x 1000mm(h) x 351mm(d)

Panel A,B,C:Total visible area: 11.81”w x 87.32”h299.9mm(w) x 2217.9mm(h)Panel D:Total visible area: 46.30”w x 86.61”h1176.1mm(w) x 2199.9mm(h)Panel E & G:Total visible area: 23.62”w x 87.32”h599.9mm(w) x 2217.9mm(h)Panel F:Total visible area: 34.49”w x 86.61”h876mm(w) x 2199.9mm(h)Header:Total visible area: 42.375”w x 12”h1076.325mm(w) x 304.8mm(h)

Refer to related graphic template for more information

additional information:

- Custom appearance- Easy to assemble- Combination of rigid and fabric graphics- Aluminum construction: vertical extrusions 50mm x 100mm- Fully printed counter graphics

features and benefits: - Kit includes one frame, one graphic header, five fabric graphic panels, two roller graphic panels, three 50 watt spotlights, one literature holder, one monitor bracket, one storage counter and three WMC12x6 molded cases- Lifetime hardware warranty against manufacturer defects

08.12.15 © Nimlok Display and Exhibit Solutions WorldwideFor questions contact your local Nimlok distributor

Shipping dimensions - ships in 3 casesEach WMC12x6 case: 52”(l) x 30”(w) x 15”(h)1320.8mm(l) x 762mm(w) x 381mm(h)

Approximate shipping weight (entire kit): 375 lbs / 170.1 kgs

Shipping

Graphic materials: dye-sublimated fabric & UV prints on 6mm sintra

Counter holds max weight 100 lbs / 45.4 kgs

Tabletop colors:

Monitor mount max weight: 50 lbs / 22.7 kgs

Lights included: LV1 50 watt, low voltage spotlight, curved arm, silver finish, 19.5” from end to end

Canopy can be upgraded to dye-sublimated graphic printed

silver black mahogany natural

Parts included

Part label Qty Part code

VE-01 x16 PM4S3-1200-A-A VE-07 x2 PM4S3-600-L-L

VE-08 x2 PM4S3-300-L-L

VE-09 x1 PH2-1200-S-S

VE-10 x1 PH2-900-S-S

VE-99 x2 PS2

VE-11 x2 PH2-600-S-S

VE-12 x4 PH2-300-S-S

VE-13 x8 PH2C-1

VE-31 x6 PH-351-S-S

VE-44 x1 PM4S2-300-L-L

SP VC-03 x1 V-CAB-02-DR

V-LWS-CT-02 x1 V-LWS-CT-02

Panel A x1 -

Panel B x1 -

Panel C x1 -

VE-53 panel D x1 PM4-RB4

Panel E x1 -

VE-54 panel F x1 PM4-RB3

Panel G x1 -

Header x1 -

Counter infill x3 - 1.

Part label Qty Part code

Graphic clip x9 -

Tool kit x1 V-TK-01

Light x3 LV1-CLP-LIGHT

Curved canopy x1 V-S-CAN-02

Standoff x2 CKSO

Cable display x1 V-CK3A

Monitor mount x1 LM-MB

Step stool x1 STEP STOOL

Steamer x1 FABRIC STEAMER-ES

[3048mm]

10'-0"[3048mm]

Step 2.Attach VE-13 internal connectors to lower VE-01 uprights using the attachment detail shown below. Slide upper VE-01s over the VE-13 internal connectors to complete the vertical posts.

VE-12

VE-01

VE-01

VE-01

VE-01

VE-01 VE-01VE-01 VE-01

VE-09

VE-10

VE-12

VE-12

VE-11

VE-11

VE-12 V-12VE-12

EXTRUSION WITH LOCKS

LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL

T HANDLE

EXTRUSIONWITH LOCKS

LOCK

EXTRUSION WITH LOCKS

LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL

T HANDLE

EXTRUSIONWITH LOCKS

LOCK

VE-01

VE-01

VE-01

VE-01

VE-01 VE-01VE-01 VE-01

VE-13

VE-13

VE-13

VE-13

VE-13

VE-13

VE-13

VE-13

POST W/ STOP

STOP

STOP

1- 2-

TOP

BOTTOM

Tension Glides

2.

Step 1.Moving from left to right, connect VE-01 uprights at base using the VE-12s, VE-08, VE-11s and VE-10 as designated in the diagram below. Connect using the attachment detail shown. Note that the VE-09 and VE-10 lock into the center channel of the VE-01 upright. Take care to turn locks only half a turn.

Step 3.Connect the VE-08/VE-44 horizontals to the completed uprights where designated in the diagram using the attachment detail below.

Step 4.Assure monitor mount is secured to the VE-99s using the wingnuts as seen in the attachment detail below. Attach both VE-99s, with monitor mount attached, to the designated VE-01 uprights using attachment detail below.

EXTRUSION WITH LOCKS

LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL

T HANDLE

EXTRUSIONWITH LOCKS

LOCK

3.

VE-07

VE-44

VE-08VE-08

VE-07

LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL

T HANDLE LOCK

EXTRUSION WITH LOCKS

EXTRUSIONWITH LOCKS

4.

Step 5.Attach VE-53/VE-54 to the designated VE-01 uprights as shown in attachment detail. Insert graphic clips into VE-09/VE-10 where designated and turn clockwise to tighten. Pull graphics down from VE-53/VE-54 and snap rods into clips. When removing, never pull on the graphic, always pull on the graphic rod.

VE-54VE-53

BOTTOM

Graphic Rod

DyesubGraphic

MIDDLECHANNEL

EXTRUSIONWITH LOCKS

The CLIP locations are represented byorange dots on the drawings.

CLIP

GRAPHICCLIP

VE-53 PANEL DVE-54 PANEL F

LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL

PHT HANDLE LOCK

EXTRUSIONWITH LOCKS

5.

Step 6.Using the attachment detail show, push rubber gasket around edge of panels A, B, C, E and G into the designated channels as seen in diagram below.

TOP

PULL TABS

Fabric graphic is installed by pressing into TOP andBOTTOM channel. To pull the graphic out of the channels, use

TABS on the back side.

BOTTOM

PULL TABS

Fabric graphic is installed by pressing into TOP andBOTTOM channel. To pull the graphic out of the channels, use

TABS on the back side.

GRAPHIC I

GRAPHIC BGRAPHIC C

GRAPHIC A

GRAPHIC G

G

E

PANEL APANEL B

PANEL C

PANEL E

PANEL G

Step 7.To attach cable display, insert clips on end of cables into the front channel of both the VE-12 and VE-44 and twist gently to the right to tighten. To attach header, connect two standoffs to the front channel of designated VE-01 uprights using detail below. Attach wings to the standoffs using detail below.

STANDOFF

CABLE DISPLAY

STANDOFF

CABLE DISPLAY

Twist in extrusion channel.Gently tight in place

EXTRUSIONCHANNEL

TOP

BOTTOM

EXTRUSIONCHANNEL

Attach STANDOFF to brochure or sintraand gently tight in place. Then link Cables

to extrusions top and bottom

2.5 MMHEX KEY

2.5 MMHEX KEY

BROCHUREOR GRAPHIC

STANDOFF

CABLE

CABLE DISPLAY

STANDOFF DETAIL

Graphic

NTToggle

STANDOFFTop

Channel ofextrusion

STANDOFF Barrel

Screw the NT toggle into the base of the STANDOFF barrel and theninsert the NT toggle into the channel of the extrusion and twist to

tighten into place. Next, place the top of theSTANDOFF through the hole in the graphic and then screw on the

STANFOFF top to secure the graphic in place.

INSTALL CABLEDISPLAY IN THE

FRONT CHANNEL

CABLE DISPLAYSTANDOFF

STANDOFF

HEADER

6.

Assemble frame as shown

Frame AssemblyFrame AssemblySET UP INSTRUCTIONS:

1. CONNECT BOTTOM AND TOP RAILS FOLLOWING THE LABELS2. CONNECT SIDE RAILS3. CLEAN THE FRAME AND PLACE THEM ON CLEAN PLACE4. CAREFULLY REMOVE FABRIC COVER FROM BAGS5. PLACE COVER AROUND THE BOTTOM OF THE FRAME6. PULL COVER CAREFULLY UP TO THE TOP7. CLOSE ALL ZIPPERS8. ADJUST FABRIC AROUND THE FRAME

BREAK DOWN INSTRUCTIONS:REVERSE SET-UP STEPS TO BREAKDOWN FRAME

FABRIC CARE INSTRUCTIONS:1. UNZIP COVER ZIPPERS2. CAREFULLY REMOVE FABRIC COVER3. CLOSE ALL ZIPPERS4. FOLD OR ROLL NEATLY5. PLACE FABRIC IN COVER BAG

PART LIST:PER UNIT6 30MM DIA. TUBE SECTIONS1 FABRIC COVER

CURVED CANOPY

12

3

45

6

#8 SHEET METAL SCREW REQUIREDW/MINIMUIM OF 3/4" LENGTH

TO SCREW THE PLATE TO THE EXTRUSION

30MM TUBE

PLATE

VERTICALEXTRUSION

#8 SCREW

ZIPPER

NOTCH BOTTOM FABRIC PANELON CENTER OF THE SPREADERTUBES FOR TUBE CONNECTION

(1.25" DIA.).

Step 8.Assemble the canopy by connecting the pieces following the numbered labels. Clean the frame and place it on a clean surface. Carefully remove the graphic and place it around the bottom of the frame, slits on underside of graphic. Pull the cover carefully over the frame and close all zippers. When breaking system down, be sure to fold or roll the graphic neatly and place in bag.

Screw supplied plates to the top of designated VE-01s as shown in detail below. Slide completed canopy onto tube secured to the plate.

CURVED

CANOPY

7.

slits in graphic go on the underside of frame

Step 9.Lock VE-31s at bottom of designated VE-01 uprights using attachment detail below. Attach SP VC-03 counter door, VE-63 and remaining VE-31 to the secured VE-31s.

Step 10.Slide front and side infills into the channels of the VE-01, SP VC-03 counter door, and VE-63 uprights.

VE-31

P90R-1000

VE-31

VE-31

SP VC-03

EXTRUSION WITHLOCKS

LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL

EXTRUSIONWITH LOCKS

T HANDLE LOCK

FRONT

INFILL

SIDE

INFILL

SIDE

INFILL

8.

VE-63

Step 11.Connect three upper VE-31s where designated in diagram below using the attachment detail shown. Set V-LSW-CT-02 counter top onto completed frame.

9.

VE-31

VE-31

VE-31V-LSW-CT-02

EXTRUSION WITHLOCKS

LOCK HORIZONTAL EXTRUSION BYUSING T- HANDLE TOOL

EXTRUSIONWITH LOCKS

T HANDLE LOCK

Step 12.Slide two lights onto clips and place in middle channel of VE-53 as shown in detail below.

LV1 Light

Light clip

1- Slide light clip onto the LIGHT.2-Then slide the LIGHT into the channel at an angleand then gently lower down.

LIGHT W/ CLIP

10.

LIGHTLIGHT

LIGHT

check out these related products:

We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications.

Redesign of this exhibit without approval by Nimlok may result in dangerous and unsafe structures. Nimlok disclaims any responsibility for redesigned exhibits it does not approve in writing. Parts and components such as panels and extrusions are manufactured to metric sizing.

velocity standard 01 velocity standard 02 velocity standard 03 velocity standard 04

velocity standard 05 velocity standard 06 velocity standard 07 velocity standard 08