victaulic catalog - pipe preparation specifications
DESCRIPTION
Victaulic GrooveTRANSCRIPT
Victaulic CatalogPipe Preparation Specifications
Flexible Radius Cut Groove Specifications - Ductile Iron Pipe
1
Nom.Size
Inchesmm
2
Pipe Outside Dia. O.D.Inches/mm
3 4 5 6 7
Dimensions - Inches/millimeters
Basic
Tolerance GasketSeatA+
+0.000-0.020
GrooveWidth
B+0.031-0.016
Groove DiaC **
RadiusR
Min. Allow.Wall Thick. T#
+ - Basic Tol.+0.000
CastIron
DuctileIron
380
3.96100.6
+0.045+1.14
-0.045-1.14
0.75019.05
0.3759.53
3.72394.56
-0.020-0.51
0.1203.05
0.328.1
0.317.9
4100
4.80121.9
+0.045+1.14
-0.045-1.14
0.75019.05
0.3759.53
4.563115.90
-0.020-0.51
0.1203.05
0.358.9
0.328.1
6150
6.90175.3
+0.060+1.52
-0.060-1.52
0.75019.05
0.3759.53
6.656169.06
-0.020-0.51
0.1203.05
0.389.7
0.348.6
8200
9.05229.9
+0.060+1.52
-0.060-1.52
0.87522.23
0.50012.70
8.781223.04
-0.025-0.64
0.1453.68
0.4110.4
0.369.1
10250
11.10281.9
+0.060+1.52
-0.060-1.52
0.93823.83
0.50012.70
10.813274.65
-0.025-0.64
0.1453.68
0.4411.9
0.389.7
12300
13.20355.3
+0.060+1.52
-0.060-1.52
0.93823.83
0.50012.70
12.906327.81
-0.030-0.76
0.1453.68
0.4812.2
0.4010.2
14350
15.30388.6
+0.050+1.27
-0.080-2.03
0.93823.83
0.62515.88
14.969327.81
-0.030-0.76
0.1654.19
0.5514.0
0.4210.7
16400
17.40442.0
+0.050+1.27
-0.080-2.03
1.18830.18
0.62515.88
17.063433.40
-0.030-0.76
0.1654.19
0.5814.0
0.4310.9
18450
19.50495.3
+0.050+1.27
-0.080-2.03
1.18830.18
0.62515.88
19.125485.78
-0.030-0.76
0.1854.70
0.6316.0
0.4411.2
Victaulic Catalog - Pipe Preparation Specifications http://www.slingchoker.com/sling2/victau/viii/vii87a.htm
1 of 2 04-05-2011 14:40
20500
21.60548.6
+0.050+1.27
-0.080-2.03
1.18830.18
0.62515.88
21.219538.96
-0.030-0.76
0.1854.70
0.6717.0
0.4511.4
24600
25.80655.3
+0.050+1.27
-0.080-2.03
1.18830.18
0.62515.88
25.406645.31
-0.030-0.76
0.1854.70
0.7318.5
0.4711.9
30750
32.00812.8
+0.080+2.03
-0.060-1.52
1.37534.93
0.75019.05
31.550801.37
-0.035-0.89
0.2155.46
0.9223.4
0.5113.0
36900
38.30972.8
+0.080+2.03
-0.060-1.52
1.37534.93
0.75019.05
37.850961.39
-0.035-0.89
0.2155.46
1.0225.9
0.5814.7
+ Must be smooth and free of deep pits or swells.** Groove must be uniform depth for entire pipe circumference. Groove must conform to "C" diameter shown.* Ovality, or out-of-roundness, must lie within specified tolerances.# Min. standard wall thickness that should be grooved. Tolerances are to conform to ANSI/AWWA C151/A21.51.For 18-36" (450 - 950 mm) ductile iron Class 53 pipe may be used. Contact Victaulic for details.
Victaulic groove specifications for cast pipe (gray and ductile) conform to requirements of ANSI/AWWA standard C-606.For cast pipe, the groove is cut with a radius ("R" dimension) at the comers of the groove base to reduce stress concentration. Grooving dimensions are the same for any one pipe O.D.regardless of pipe class and pressure.Standard preparation is with a rigid radius groove. Flexible radius groove dimensions may be used to provide expansion/contraction or angular movement allowance at the joint.The outside surface of the pipe between the groove and pipe end must be smooth and free from deep pits or swells to provide a leak-tight seat for the Victaulic gasket. All rust, loosescale, oil, grease and dirt shall be removed. Peened surfaces may require corrective action to provide leak-tight gasket seal (refer to ANSI/AWWA C-606).Request 25.05 for Flexible and Rigid Radius Cut Groove Specifications.
Victaulic Catalog - Pipe Preparation Specifications http://www.slingchoker.com/sling2/victau/viii/vii87a.htm
2 of 2 04-05-2011 14:40