vswr measurement using anritsu site master
TRANSCRIPT
7/28/13 VSWR Measurement using Anritsu Site Master
denmasbroto.com/article-12-vswr-measurement-using-anritsu-site-master.html 1/5
Home About Us Contact Us Submit
Last Post Comments Tags
Antenna basic theory
VSWR Measurement using AnritsuSite Master
VSWR (Voltage Standing WaveRatio)
Blackberry Technology
3G Modem Connections
3G Specifications
Cellular TelecommunicationAbbreviations
GPRS Network Architecture
BTS Configuration Diagram
The Generations before GSM
UMTS-3G Network Architecture
Basic GSM Configuration
2013-07-15 02:07:31,
BTS Configuration Diagram vodafon - oleh : amrgood
2013-07-07 13:25:35, Basic GSM Configuration about gsm component - oleh : vivek
kumarI want to ditel of gsm component
2013-06-03 00:15:09,
BTS Configuration Diagram wonderful - oleh : Andy Andersonvery very useful infor
2013-05-10 10:45:01, UMTS-3G Network Architecture Articles - oleh : B.Hannan Mullah
ManzoorArticles
2013-05-01 22:06:24,
VSWR Measurement using AnritsuSite Master RX level - oleh : aimTell me there are our 1 site of nokiafl...
2013-04-10 19:16:34, VSWR Measurement using AnritsuSite Master High rssi - oleh : MannyWould u happen to have any tiopson trou...
2013-03-17 16:41:59, BTS Configuration Diagram technical - oleh : sathishdocument
2013-02-22 14:43:57, VSWR Measurement using Anritsu
Site Master Kindly send me detailed Note onThe Application Of Site Analyzer forAlcatel Lucent - oleh : ohiaru Interesting to read here
2013-02-15 15:08:50, GPRS Network Architecture
VSWR Measurement using Anritsu Site Master
Tuesday, 2 August 2011 20:30:24 - by : admin
To measure the VSWR there areseveral ways you can use, one of
them by using the VSWR AnritsuSite Master S332B.
With this tools we are very watereddown to take measurements withaccurate results and the resultscan be printed or in the save in afiles.
Equipment needed to perform measurements, namely:
1. Anritsu Site Master S332B type2. Precision OPEN / SHORT,
3. Precision Terminator / LOAD4. Extension Test Cable.
There are 5 (five) items measuring procedures, including:
1. Setting Frequency and Calibration2. VSWR measurement3. Measurement of Return Loss (RL)
4. Measurement of Distance to Fault (DTF)5. Measurement Cable / Waveguide Loss (CL)
I. Setting Frequency and CalibrationBefore conducting measurements, the instruments should be calibrated in advance, while thesteps are as follows:
A). SETTING RANGE FREQ.1. Press the MODE2. Select FREQ-VSWR or Return Loss3. Press ENTER4. Press the FREQ / DIST
5. Press the F1 soft key6. Enter the numbers 8,9,0 or select a predetermined Freq / stored7. Press ENTER to determine F1 = 890 MHz8. Press the F2 soft key9. Enter the numbers 9,6,0 or select a predetermined Freq / stored10. Press ENTER to determine F2 = 960 MHz
B). CALIBRATION
1. Press the START CAL the message "Connect Open to the RF out port"
2. Pairs of precision "OPEN" and then press ENTER, the message "Measuring OPEN"after the process is complete the message "Connect SHORT to RF out port"
3. Remove the precision OPEN, SHORT precision pairs and then press the ENTER keyand the message will appear "Measuring SHORT" after that message appears again'Connect termination to the RF out "
4. Remove the plug precision and precision termination SHORT press ENTER and themessage "Measuring termination"
5. Check at the top left corner posts CAL ON (measuring instruments are properly
Categories
Related Link
Calendar
Hijjrah Date
Cellular Theory
Microcontroller
Tips And Tricks
Transmission System
Antennas
Gadget Guides
« ‹ Jul 2013 › »
M S S R K J S
30 1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30 31 1 2 3
4 5 6 7 8 9 10
RAMADHAN
20AHAD1434
7/28/13 VSWR Measurement using Anritsu Site Master
denmasbroto.com/article-12-vswr-measurement-using-anritsu-site-master.html 2/5
hhhh - oleh : ravshantext
2013-02-06 14:48:55, VSWR Measurement using Anritsu
Site Master VSWR MEASUREMENT - oleh :samuel molishocomment mesure le vswr et dtf
2013-02-05 18:26:22, BTS Configuration Diagram INTERESTING - oleh : EMMANUEL
I FIND THE SITE VERYINTERESTING
2013-02-04 02:20:19, BTS Configuration Diagram telecom - oleh : NSEMBOLOAPPRENDRE LA
TÉLÉCOMMUNICATION
2013-01-18 15:17:29, VSWR Measurement using AnritsuSite Master vswr measurement - oleh : DimitriosSiontoros
vswr measurement using AnritsuSite Mast...
2012-12-21 17:27:42, BTS Configuration Diagram nice - oleh : yemyothuIt is good for the first step of basic l...
2012-12-21 16:28:29,
Cellular TelecommunicationAbbreviations
good - oleh : yemyothu
nice for 3g network learners,thankyou
antenna, antenna beamwidth, parabolic antenna,
radiation pattern, rf sy stem, v swr, v swr
measurement, v swr v alue
Login
Username
Password
Login
Register
Forgot Password
Short Message
mewan : i need to know RFplaning
Rabu, 10 Juli 2013 15:45:52
afsar ali siddi : Best site for GSMInfo, can update send to mymail every time
Sabtu, 09 Februari 201307:59:17
nazish : hi
Senin, 14 Mei 2012 02:08:54
» New Entry
Statistic
calibrated).
C). Amplitude / LIMIT
1. Press the amplitude or LIMIT to go to the scales.
2. Eg for press softkey TOP VSWR, specify the value of it (eg: 1.3) and press the BOTTOMfor determining the underlying value (eg: 1).
3. Eg for press softkey TOP RETURN LOSS, determine its value (eg: 0) and press theBOTTOM to determine its value (eg: 54)
D). SAVE SETUPTo save the configuration settings press SETUP SAVE then use the arrows to select locations1-10 and ENTER.
E). RECALL SETUP
1. Press the RECALL SETUP.
2. Use the arrows to select the desired setting that ekan then ENTER.
F). SAVE DISPLAY
1. Press SAVE DISPLAY to activate the alphanumeric menu
2. Use the softkey to enter the letters / numbers that will be stored in memory.
G). RECALL DISPLAY
1. Press the RECALL DISPLAY
2. Use the arrows to select the data that will be displayed and then ENTER.
II. VSWR measurement
1. Press the MODE button.
2. Use the arrows to select the FREQ-SWR and then press ENTER.
3. To select a frequency range such as PROCEDURE A.
7/28/13 VSWR Measurement using Anritsu Site Master
denmasbroto.com/article-12-vswr-measurement-using-anritsu-site-master.html 3/5
Visitors :130598 User
Hits : 256241 hits
Month : 3544 Users
Today : 76 Users
Online : 1 Users
ip logs
157.55.34.252013-07-28 10:05:41
198.2.218.82013-07-28 05:45:42
157.55.33.1822013-07-26 12:15:09
46.19.230.172013-07-22 21:37:15
46.19.230.172013-07-22 21:37:14
46.19.230.172013-07-22 21:37:13
46.19.230.172013-07-22 21:37:10
46.19.230.172013-07-22 21:37:09
46.19.230.172013-07-22 21:37:08
46.19.230.172013-07-22 21:37:07
4. Then the calibration like procedure B.
5. After that plug feeder (end loaded antennas) to gauge or can also use the extension
cable from the measuring instrument, this is to facilitate the mobilization ofmeasurement.
6. Then observe the results of measurements and mark with marker amplitude graph
MARKER SETTING
1. Press the MARKER button to go to the marker.
2. M1 softkey, press the EDIT softkey and enter a value
3. who desired frequency (eg: 900) press ENTER, the setting M1 = 900 MHz. Press BACK
softkey to return to the marker.
4. Repeat Step 1 and 2 for M2.
III. Return Loss Measurement
1. Press the MODE button.
2. Use the arrows to select the FREQ-RETURN LOSS and then press ENTER3. The next steps together with VSWR measurements.
V. Measurement of Distance to Fault
1. Press the MODE
2. Use the arrows to select the DTF-SWR ENTER
3. Calibration and range setting freq. like steps A & B.
IV. Measurement Cable / Waveguide Loss
Cable Loss Measurement using Precision SHORT at the end of feeder
1. Press the MODE
2. Use the arrow and select the ONE-PORT CABLE LOSS, press ENTER
3. Press to enter the menu amplitude scale
4. Press softkey and define the values it TOP
5. BOTTOM softkey and define the bottom.
THINGS TO NOTE:
7/28/13 VSWR Measurement using Anritsu Site Master
denmasbroto.com/article-12-vswr-measurement-using-anritsu-site-master.html 4/5
Calibration of measuring instruments must always be done before starting the
measurements.
Knowing the specifications of the material such Loss Connector, Feeder, feeder
jumpers, splitters, antenna and others.
Before measuring, make sure first that the installation is mounted fine.
Using the extension cable to move more freely in doing measurement
Send to a friend | Print
Here is other references
Other "Antennas" Articles
VSWR (Voltage Standing Wave Ratio)
Antenna basic theory
Comments
12. RX levelWednesday, 1 May 2013 22:06:24 - Oleh : aim
Tell me there are our 1 site of nokia flexi there we use ldf7 cable we remake all connectors and fully tight
them but there Rx level is high tell me its solution.
11. High rssiWednesday, 10 April 2013 19:16:34 - Oleh : Manny
Would u happen to have any tiops on trouble shooting high rssi??
10. Kindly send me detailed Note on The Application Of Site Analyzer for Alcatel Lucent Friday, 22 February 2013 14:43:57 - Oleh : ohiaru
Interesting to read here
9. VSWR MEASUREMENTWednesday, 6 February 2013 14:48:55 - Oleh : samuel molisho
comment mesure le vswr et dtf
8. vswr measurementFriday, 18 January 2013 15:17:29 - Oleh : Dimitrios Siontoros
vswr measurement using Anritsu Site Master
1 | 2 | 3 | Next »
7/28/13 VSWR Measurement using Anritsu Site Master
denmasbroto.com/article-12-vswr-measurement-using-anritsu-site-master.html 5/5
Home About Us New s feed Sitemap Back to Top
Name :
Email :
Comment Title :
Comment :
Security Code :
Type Code :
Send
© 2007-2011 Pow ered by AuraCMS. Supported By subadar