vt-sbcq7-mx6q user’s manual (hardware)€¦ · imx31, imx53，imx6, samsung s3c6410, ti omap35xx...

VT-SBCQ7-MX6Q Boards User’s Manual

VT-SBCQ7-MX6Q

User’s Manual (Hardware)

Chengdu Vantron Technology Ltd. Co.


All rights reserved , Total 30

Revision record

Date Version Change Description

2018-06-14 1.0 Initial Version

2018-07-30 2.0 Modified Display description



Table of Contents

1.1 COPYRIGHT NOTICE ......................................................................................................................................................4 1.2 NOTES..........................................................................................................................................................................4 1.3 STATEMENT ..................................................................................................................................................................4 1.4 DISCLAIMER..................................................................................................................................................................4 1.5 LIMITATION OF LIABILITY/NON-WARRANTY....................................................................................................................4 1.6 SAFETY INSTRUCTIONS ..................................................................................................................................................5 1.7 PRECAUTIONS ...............................................................................................................................................................5 1.8 SAFETY INSTRUCTIONS FOR POWER CABLES AND ACCESSORIES .......................................................................................5

2 OVER VIEW .......................................................................................................................................................................7

2.1 INTRODUCTION .............................................................................................................................................................7

3 SBCQ7-MX6Q HARDWARE INSTRUCTIONS................................................................................................................8

3.1 BOARD DIAGRAM .........................................................................................................................................................8 3.2 BOARD ASSEMBLY DRAWING ........................................................................................................................................9 3.3 BOARD STRUCTURE.................................................................................................................................................... 11

4 HARDWARE DESCRIPTION.......................................................................................................................................... 13

4.1 IDENTIFY CONNECTOR ................................................................................................................................................ 13 4.1.1 Position of connector .................................................................................................................................. 13 4.1.2 Confirm the pin direction ........................................................................................................................... 13

4.2 SWITCH, BUTTONS, JUMPERS, LEDS........................................................................................................................... 13 4.2.1 S1 Boot Settings........................................................................................................................................... 13 4.2.2 B1, RTC Battery ............................................................................................................................................ 13

4.3 LCD,DISPLAY ............................................................................................................................................................. 14 4.4 TP,TOUCH PANEL....................................................................................................................................................... 14 4.5 CONNECTORS DESCRIPTION........................................................................................................................................ 14

4.5.1 J1, LCD display port ..................................................................................................................................... 15 4.5.2 J2, HDMI port ............................................................................................................................................... 16 4.5.3 J3,Audio port ................................................................................................................................................ 17 4.5.4 J4&J5, Speaker port..................................................................................................................................... 17 4.5.5 J6, Micro USB Port ....................................................................................................................................... 17 4.5.6 J7, Internal USB port ................................................................................................................................... 17 4.5.7 J8,Internal USB port .................................................................................................................................... 18 4.5.8 J9, 10/100/1000M Ethernet port.............................................................................................................. 18 4.5.9 J10,CAN port................................................................................................................................................. 18 4.5.10 J11,Debug UART Connect port .................................................................................................................. 18 4.5.11 J12,JTAG port ............................................................................................................................................... 18 4.5.12 J13,RS232 port ............................................................................................................................................. 19 4.5.13 J14, SIM card slot......................................................................................................................................... 19 4.5.14 J15,SATA Power connector ........................................................................................................................ 19 4.5.15 J16,MINI-PCIE connector............................................................................................................................ 19 4.5.16 J17,power supply port ................................................................................................................................ 20 4.5.17 J19,Reserve port .......................................................................................................................................... 20 4.5.18 J20 ,SATA....................................................................................................................................................... 21 4.5.19 J21, RF antenna for WiFi&BT..................................................................................................................... 21 4.5.20 J64, Backlight ............................................................................................................................................... 21 4.5.21 J23, 230 pin Gold-Finger............................................................................................................................. 21

4.6 HARDWARE OPERATION NOTES ................................................................................................................................. 28

5 TIPS.................................................................................................................................................................................. 29



1.1 Copyright Notice

While all information contained herein have been carefully checked to assure its accuracy in

technical details and printing, Vantron assumes no responsibility resulting from any error or features

of this manual, or from improper uses of this manual or the software. Please contact our technical

department for relevant operation solutions if there is any problem that cannot be solved according to

this manual.

Vantron reserves all rights of this manual, including the right to change the content, form, product

features, and specifications contained herein at any time without prior notice. The latest version of

this manual is at www.vantrontech.com.cn. Please contact Vantron for further information:

Vantron Technology（Vantron）

E-mail: [email protected]

The trademarks and registered trademarks in this manual are properties of their respective owners.

No part of this manual may be copied, reproduced, translated or sold. No changes or other purposes

are permitted without the prior written consent of Vantron.

Vantron reserves the right of all publicly-released copies of this manual.

1.2 Notes

Applicable notes are listed in the following table:

Sign Notice

Type Description

Notice Important information and regulations

Caution

Caution for latent damage to system or

harm to personnel

1.3 Statement

It is recommended to read and comply with this manual before operating board, which provides

important guidance and helps decreasing the danger of injury, electric shock, fire, or any damage to

the device.

1.4 Disclaimer

Vantron assumes no legal liability of accidents resulting from failure of conforming to the safety

instructions.

1.5 Limitation of Liability/Non-warranty



For direct or indirect damage to this device or other devices of Vantron caused by failure of

conforming to this manual or the safety instructions on device label, Vantron assumes neither

warranty nor legal liability even if the device is still under warranty.

1.6 Safety Instructions

Keep and comply with all operation instructions, warnings, and information.

Pay attention to warnings on this device.

Read the following precautions so as to decrease the danger of injury, electric shock, fire, or any

damage to the device.

1.7 Precautions

Pay attention to the product labels/safety instructions printed on silk screens.

Do not try repairing this product unless declared in this manual.

Keep away from heat source, such as heater, heat dissipater, or engine casing.

Do not insert other items into the slot (if any) of this device.

• Keep the ventilation slot ventilated for cooling.

•System fault may arise if other items are inserted into this device.

Installation: ensure correct installation according to instructions from the manufacturer with

recommended installation tools.

Ensure ventilation and smoothness according to relevant ventilation standard.

1.8 Safety Instructions for Power Cables and Accessories

Proper power source only

Start only with power source that satisfies voltage label and the voltage necessary according to this

manual. Please contact technical support personnel of Vantron for any uncertainty about the

requirements of necessary power source.

Use tested power source

This product still contains a button lithium battery as a real-time clock after its external power source

is removed and therefore should not be short-circuited during transportation or placed under high

temperature.

Place cables properly:

Do not place cables at any place with extrusion danger.



Cleaning Instructions

Please power off before cleaning the device.

Do not use spray detergent.

Clean with a damp cloth.

Do not try cleaning exposed electronic components unless with a dust collector.

Support for special fault: Power off and contact technical support personnel of Vantron in case of

the following faults:

The device is damaged.

The temperature is excessively high.

Fault is still not solved after the operation according to the manual.



2 Over View

2.1 Introduction

Vantron offers both ARM and ATOM based Single Boards Computer (SBC) platforms

including Cirrus Logic EP9315, Marvell PXA255, PXA270, and PXA320, Intel IXP465, FreeScale

iMX31, Imx53，iMX6, Samsung S3C6410, TI OMAP35xx CortexA8 series, and Intel ATOM Z510

and Z530 processor boards. In additional to offering the standard SBCs, we also provide

professional customization board design services. Our seamless project management, efficient

error-free development process, strong fundamentals in technology, sufficient in human

resources, and on-time delivery will guarantee the success in your project development.

Based on idea of “Application Ready” products and services, our embedded computers have

embedded basic operation system which includes the drivers of its interfaces. So it is easy to be

used by adding your application software only. It can speed Time to Market of your products, and

saving more cost.

SBCQ7-MX6Q is an A9 processor based board with 9” LCD display. And the function such as:

Freescale IMX6Q,1GHz,Low Power Processor. With a 1280x240 TFT-LED With a touch panle

Supports 802.11b,g,n WiFi 2.4GHz and Bluetooth 4.1 Embedded Linux, Android ,WinCE, Supported



3 SBCQ7-MX6Q Hardware Instructions

3.1 Board Diagram

USB OTGTYPE-C

USB TYPEC

OTG

Power Rail

I2C2

U.FL connector for external antenna

Accel (3-axis)

Debug PortJack

UART1， 2-wires

PMICTPS659114

+System power PWRKEY

Reset

SIM Slot#1

SDIO WiFi & Bluetooth ModuleAP6255

Headphone

Audio CodecWM8960

I2C1I2S

MIC

Power Rail

USB 3.0

RGMII RJ45

USB3

USB4

UART2， 2-wires

Type-A

I2C2

SDIO0UART5BT4.1

802.11a/b/g/n/ac

CON

eDP-2xLVDS

1x6x2.54

eDP

HD

MI O

UT

TP,I2

C4

MINI-PCIE

PCIE

HUB

USB2.0 H

OST1

USB2

USB1

1x2x2.541x2x2.54

SPK-

L

SPK-

R

AudioJACK

PowerJack

DC-DCTPS5450 12V input

(8-17V Range)DC-DCRT8299

3.3V

1x6x2.54

DC-DCTPS62136

3.3V

5V

For 3/4G and PCIE device

: IC Chip: Connector

Type-A,RADual USB

1x4x1.25

1x4x1.25

1x30x0.5

MIPI

CameraTouchDisplayDisplay

RS232

TJA1040CAN CAN

RS232



3.2 Board Assembly Drawing

Top view



Bottom view



3.3 Board Structure



4 Hardware Description

This chapter describes the hardware Features, include switch, jumper, connector and PIN function

The interface description ought to consult the connector sketch map. And attach necessary message such as picture. Indicate the figure, PIN1 and match jack

4.1 Identify connector

This section describes how to find the position of connector and PIN1 on SBCQ7-MX6Q-COMBI single computer board.

4.1.1 Position of connector As Figure 3.2 show the main part and connector position of SBCQ7-MX6Q-COMBI.

4.1.2 Confirm the pin direction There is the pin number order in all Vantron’s

product, this picture at right indicate each pin’s number, that message as show on the top side(component side) of main board. on double row connector, one side is naming odd number and another side is naming even number. Please according to below method to confirm the Pin1 of connector and jumper: 1. Usually, there is any number and mark at side of connector in main board, such as

trigonal mark, dot and number “1” all indicate the pin1 of connector 2. About the hole connector, you can see pin number on the reversed side 3. Download the SBCQ7-MX6Q mechanism from Vantron technology sustain or Vantron

net site: www.vantrontech.com

4.2 Switch, Buttons, Jumpers, LEDs

This section describes the setting of switch, controller, LED on SBCQ7-MX6Q board.

4.2.1 S1 Boot Settings SBCQ7-MX6Q support three kinds of boot up method, by 2 bit DIP Switch(S1). It can be boot up form USB OTG,SD Card, eMMC. Start up method SYS_BOOT[1:0]

SD Card 1 0

eMMC 0 1

USB OTG 0 0

4.2.2 B1, RTC Battery B1 is for RTC Battery. The suggest part is BR1225A from PANASONIC.



4.3 LCD,display

General specification of the 7” LCD.

Item Feature Spec

Characteristics

Resolution 1280(RGB)x240

Pixel Pitch 0.17475x0.17475

Pixel Configuration R.G.B Vertical Stripe

LED Numbers 40 LEDs

Interface LVDS

Color Depth 16.7M

4.4 TP,touch panel

7" TP/5071-TM-FP GEN2,I2C,3.3V,1.77mm,6H,-20~60℃

Pin Name Description

1 VCC 5V

2 D- USB DATA-

3 D+ USB DATA+

4 GND Ground

5 GND Ground

4.5 Connectors Description

This table is the respective describe valid signal of connector on SBC-Q7-MX6Q board. Figure type: N/C Not connect

GND Ground

/ active low signal

+ Positive of difference signal

- negative of difference signal

Signal type: I Input

O Output

IO input/output

P Power or ground

A Analog

OD Open drain



4.5.1 J1, LCD display port 1x40,0.5mm,0.5A,1.05mm,M,RA,WDT,SMT,RoHS (JAE: HD1S040HA1)

Pin Name Type Description

1 LCD_VDD P LCD digital power supply +3.3V



4 RST O TP Reset

5 LVDSA_DATA#0_R O EDP/LVDSA data

6 LVDSA_DATA0_R O EDP/LVDSA data

7 GND P Ground



10 GND P Ground



13 GND P Ground

14 LVDSA_CLK#_R O EDP data/LVDSA clock

15 LVDSA_CLK_R O EDP data/LVDSA clock

16 GND P Ground



19 INT I TP Interrupt

20 LVDSB_DATA#0_R O LVDSB data

21 LVDSB_DATA0_R O LVDSB data

22 GND P Ground



25 GND P Ground



28 GND P Ground

29 LVDSB_CLK#_R O LVDSB clock

30 LVDSB_CLK_R O LVDSB clock

31 GND P Ground





34 LVDS_BKLTEN O LCD backlight enable signal

35 LVDS_BKLTCTL O LCD backlight PWM signal

36 LVDS_DDC_CLK_R O I2C clock

37 LVDS_DDC_DATA_R IO I2C data

38 LCD_BLK P LCD backlight power supply +5V



4.5.2 J2, HDMI port Type A,NoFLN,F,RA,-20~85℃,SMT,RoHS (MOLEX: 47151-1001)


1 HDMI_D2P O HDMI Data2+

2 GND P Ground

3 HDMI_D2N O HDMI Data2-


5 GND P Ground



8 GND P Ground


10 HDMI_CLKP O HDMI CLK+

11 GND O Ground

12 HDMI_CLKN O HDMI CLK-

13 HDMI_CEC_OUT I

14 NC O NC

15 H_CLK_OUT O HDMI CLK OUT

16 H_DAT_OUT O HDMI DATA OUT

17 GND P Ground

18 HDMI+5V P Power Supply

19 HP_DET_OUT I HP detect

20 GND P Ground

21 GND P Ground

22 GND P Ground

23 GND P Ground



4.5.3 J3,Audio port 3.6mm,4Pole+1Switch,1Port,F,RA,CMT,THR,RoHS (HITCONN: PJ-3106H-1)

Standard audio jack with Headphone and MIC


2 MIC_RAW O MIC

4 HP_L O Headphone left channel

6 HP_R O Headphone right channel

7 HEADPHONE_DET I Headphone detect

3 GND P Ground

4.5.4 J4&J5, Speaker port Support 2.5W/4Ω speaker

1x2,2.5mm,3A,7mmH,M,Vert,-25~85℃,THR,RoHS (NSXD: S2501WV-2P)


J4-1 SPKPL O Speaker left channel

J4-2 SPKNL O

J5-1 SPKNR O Speaker right channel

J5-2 SPKPR O

4.5.5 J6, Micro USB Port 2.0,Micro AB,1Port,F,RA,-30~85℃,SMT,RoHS


1 USB_OTG_CON_VBUS P USB_OTG Power detect

2 USB_OTG_CON_DN O USB_OTG Data-

3 USB_OTG_CON_DP O USB_OTG Data+

4 USB_OTG_ID I USB_OTG ID

5 USB_OTG_CON_GND P Ground

4.5.6 J7, Internal USB port 1x4,2.5mm,3A,7.0mmH,M,Vert,IND,THR,RoHS (ATOM: AWF-2540104-D08)


1、2 USBH0_GND P Ground

3 USBH0+ IO USB Data0+

4 USBH0- IO USB Data0-

4 USBH0_VCC P USB power



4.5.7 J8,Internal USB port 2.0,TYPE A,1Port,F,RA,CMT,THR,RoHS


A1 USBH3_VCC P USB power

A2 USBH3- IO USB Data3-

A3 USBH3+ IO USB Data3+

A4 USBH3_GND P Ground

B1 USBH2VCC P USB power

B2 USBH2- IO USB Data2-

B3 USBH2 IO USB Data2+

B4 USBH2_GND P Ground

4.5.8 J9, 10/100/1000M Ethernet port 10/100/1000,MAG,2LED,1Port,SHLD,F,RA,-40~85℃,THR,RoHS

(UNE: U50(02-02)G8-09-A122-B12)

4.5.9 J10,CAN port 1x2,2.5mm,3A,7mmH,M,Vert,-25~85℃,THR,RoHS


1 CAN0_HIGH IO CAN Data

2 CAN0_LOW IO CAN Data

4.5.10 J11,Debug UART Connect port 3.6mm,3Pole,1Port,F,RA,CMT,THR,RoHS (KBIT: PJ-320F)

Matched debug cable PN: YC1083R035


1 GND P Ground

2 TXD O Data Transmit

3 RXD I Data Receive

4.5.11 J12,JTAG port 2x4,2x2mm,2A,4.7mmH,M,Vert,WDT,SMT,RoHS


1 JTAG_TCK I Clock Input

2 JTAG_TDI I Data Input



3 JTAG_TDO O Data Output

4 JTAG_TMS I Mode Select

5 JTAG_TRST# I Reset

6 JTAG_TRST# I Reset

7 GND_3V3 P Power Supply

8 GND P Ground

4.5.12 J13,RS232 port 1x5,2.0mm,2A,6mmH,M,Vert,WDT,THR,RoHS


1 GND P Ground

2 RXD2/RS485_2_A I RS232 Data Receive/RS485_A

3 TXD2/RS485_2_B O RS232 Data Transmit/RS485_B

4 RST2 IO Request to Transfer

5 CTS2 IO Clear to Send

4.5.13 J14, SIM card slot Micro,Push-Push,6P,WDT,SMT,RoHS (CSCONN: CSI06127135002)


1 PCIE_UIM_PWR P Power Supply

2 PCIE_UIM_RST I SIM Reset

3 PCIE_UIM_CLK I SIM Clock

5 GND P Ground

6 PCIE_UIM_VPP IO SIM Vpp power

7 PCIE_UIM_DATA IO SIM Data

4.5.14 J15,SATA Power connector 1x4,2.5mm,3A,7.0mmH,M,Vert,IND,THR,RoHS


1 +12V P Power Supply

2 GND P Ground

3 GND P Ground

4 +5V P Power Supply

4.5.15 J16,MINI-PCIE connector Mini,52P,0.8mm,6.8mmH,WDT,SMT,RoHS (TYCO: 2041262-1)



Support kinds of 3G/4G module with USB interface

4.5.16 J17,power supply port 2mmd,6mmd,3A,12V,M,NoLock,RA,-25~85℃,THR,RoHS

(HITCONN: DC-044A-2.0-PU)


1 12V-IN+ P Type 12V power input (Range:8-16V)



4 12V-IN- P Ground

5 12V-IN- P Ground

6 12V-IN- P Ground

4.5.17 J19,Reserve port 2x10,2x2mm,1.5A,4.6mmH,F,Vert,WDT,SMT,RoHS


1 GEN_3V3 P Power

2 LVDS1_EDID_SDA IO LVDS1_EDID_Data

3 PWR_ON IO Power key reserved

4 LVDS1_EDID_SCL IO LVDS1_EDID_Clock

5 I2S0_RST#

I2S0_Reset

6 GND P Ground

7 SEL68 O TP RST

8 I2C2_SCL_CON IO LVDS1_EDID_Data

9 SDIO_CD# IO SDIO_CD#

10 I2C2_SDA_CON IO LVDS1_EDID_Clock

11 SPI0_MISO IO SPI0_Master in slave out

12 SDIO_ACT# IO SDIO_ACT#

13 SPI0_MOSI IO SPI0_Master out slave in

14 SPI0_CS0#

SPI0_CS0#

15 SPI0_SCLK IO SPI0_Clock

16 SPI0_CS1#

SPI0_CS1#

17 SPI0_SCLK IO SPI0_Clock

18 GEN_3V3 P 3.3V POWER

19 GPIO3 IO TP INT



4.5.18 J20 ,SATA STD,7P,F,Vert,CMT,THR,RoHS


1 GND P Ground

2 SATA_TXP IO SATA Receive+

3 SATA_TXN IO SATA Receive-

4 GND P Ground

5 SATA_RXN IO SATA Transmit-

6 SATA_RXP IO SATA Transmit+

7 GND P Ground

4.5.19 J21, RF antenna for WiFi&BT 50R,6GHz,N/A,F,Vert,WDT,SMT,RoHS (HIROSE: U.FL-R-SMT(01))

4.5.20 J64, Backlight 1x6,2.5mm,3A,7mmH,M,Vert,WDT,THR,RoHS


1/2 LCD_BLK P +12V Default（5V OPT）

3 BKTLCTL_R IO LVDS backlight enable

4 BLK_PWM IO LVDS backlight adjust

5/6 GND P Ground

4.5.21 J23, 230 pin Gold-Finger Mini,230P,0.5mm,7.8mmH,WDT,SMT,RoHS

20 GND P Ground


10 RGMII_TRXN0 IO

1000M Ethernet

12 RGMII_TRXP0 IO

9 RGMII_TRXN1 IO

11 RGMII_TRXP1 IO

4 RGMII_TRXN2 IO

6 RGMII_TRXP2 IO

3 RGMII_TRXN3 IO

5 RGMII_TRXP3 IO



7 GBE_LINK100# O 100M speed indicate

8 GBE_LINK1000# O 1000M speed indicate

13 GBE_LINK# O Ethernet port link indicate

14 GBE_LINK_ACT# O Ethernet port activity indicate

15 GBE_CTREF

18 CB_PWR_ON# I This signal shuts off 5V power supply

20 POWER_BTN# I Power button signal

21 SLEEP_BTN# I Sleep button signal

26 CB_PWR_GOOD I Carrier board power good signal

27 BAT_LOW# I Battery level low signal

28 RESET_IN# I Reset button signal

29 SATA0_TX+ IO

SATA Interface

31 SATA0_TX- IO

33 SATA_ACT# O

35 SATA0_RX+ IO

37 SATA0_RX- IO

41 BOOT_DIS# I

42 SDIO_CK IO

8-bit SDIO

43 SDIO_CD# I

44 SDIO_ACT# O

45 SDIO_CMD IO

46 SDIO_WP O

48 SDIO_D1 IO

49. SDIO_D0 IO

50 SDIO_D3 IO

51 SDIO_D2 IO

52 SDIO_D5 IO

53 SDIO_D4 IO

54 SDIO_D7 IO

55 SDIO_D6 IO

47 SDIO_PWR_EN# O SDIO PWR control :active low

59 I2S0_LRCK IO

I2S Interface 61 I2S0_RST# O

63 I2S0_CLK IO



65 I2S0_SDI IO

67 I2S0_SDO IO

60 I2C3_SCL_CON IO I2C channel 2

62 I2C3_SDA_CON IO

66 I2C2_SCL_CON IO I2C channel 3

68 I2C2_SDA_CON IO

69 THRM# I Carrier thermal sensor signal

70 WDT_TIME_OUT# O

72 WDT_OUT# O Watchdog output

56 USB_OTG_PWREN O OTG port power control

80 USB4_5_OC# I USB port 4&5 over current indicate



82 USB4- IO Universal Serial Bus Port 4 differential pair.

84 USB4+ IO

87 USB3- IO Universal Serial Bus Port 3 differential pair

89 USB3+ IO


90 USB2+ IO

91 USB_OTG_VBUS_DET I OTG VBUS PWR detect

92 USB_OTG_ID# O OTG ID

93 USB_OTG- IO Universal Serial Bus OTG differential pair

95 USB_OTG+ IO


96 USB0+ IO

99 LVDS0_D0+ IO

LVDS Channel 0

101 LVDS0_D0- IO

103 LVDS0_D1+ IO

105 LVDS0_D1- IO

107 LVDS0_D2+ IO

109 LVDS0_D2- IO

113 LVDS0_D3+ IO

115 LVDS0_D3- IO

119 LVDS0_CLK+ IO

121 LVDS0_CLK- IO



125 LVDS0_EDID_SDA IO

127 LVDS0_EDID_SCL IO

100 LVDS1_D0+ IO

LVDS Channel 1

102 LVDS1_D0- IO

104 LVDS1_D1+ IO

106 LVDS1_D1- IO

108 LVDS1_D2+ IO

110 LVDS1_D2- IO

114 LVDS1_D3+ IO

116 LVDS1_D3- IO

120 LVDS1_CLK+ IO

122 LVDS1_CLK- IO

126 LVDS1_EDID_SDA IO

128 LVDS1_EDID_SCL IO

111 LCD_VDD_EN O LCD Power enable active low

123 LCD_BKLT_PWM O LCD backlight pwm

112 LVDS_BKLT_EN O LCD backlight enable active low

129 CAN0_TX IO CAN channel 0

130 CAN0_RX IO

131 HDMI_CK+ IO

HDMI interface

133 HDMI_CK- IO

137 HDMI_D1+ IO

139 HDMI_D1- IO

143 HDMI_D0+ IO

145 HDMI_D0- IO

149 HDMI_D2+ IO

151 HDMI_D2- IO

150 HDMI_CTRL_DAT IO

151 HDMI_CTRL_CK IO

153 HDMI_HPD# IO

124 HDMI_CEC IO

132 UART4_TX IO

UART channel 4 134 UART4_RX IO

144 UART4_CTS O

146 UART4_RTS I



155 PCIE_REFCK+ IO

PCIE2.0 interface

157 PCIE_REFCK- IO

179 PCIE_ATX+ IO

181 PCIE_ATX- IO

180 PCIE_ARX+ IO

182 PCIE_ARX- IO

156 PCIE_WAKE# O PCIE device wakeup

158 PCIE_RST# O PCIE device reset

171 UART2_TX IO

UART channel 2 177 UART2_RX IO

172 UART2_CTS# O

178 UART2_RTS# I

174 UART_TX IO Debug uart

176 UART_RX IO

185 GPIO0 IO

Reserved GPIO

186 GPIO1 IO

187 GPIO2 IO

188 GPIO3 IO

189 GPIO4 IO

190 GPIO5 IO

191 GPIO6 IO

192 GPIO7 IO

194 GP_PWM_OUT2 O

196 FAN_PWMOUT/GP_PWM_OUT1 O

199 SPI0_MOSI IO

SPI interface

200 SPI0_CS0# O

201 SPI0_MISO IO

202 SPI0_CS1# O

203 SPI0_SCLK IO

204 JTAG_TRST# O

JTAG interface

207 JTAG_TCK IO

208 JTAG_TDI IO

209 JTAG_TDO IO

210 JTAG_TMS IO

1 GND1 P GND



2 GND2 P

23 GND3 P

24 GND4 P

25 GND5 P

34 GND6 P

39 GND7 P

40 GND8 P

57 GND9 P

58 GND10 P

73 GND11 P

74 GND12 P

97 GND13 P

98 GND14 P

117 GND15 P

118 GND16 P

135 GND17 P

136 GND18 P

141 GND19 P

142 GND20 P

147 GND21 P

148 GND22 P

159 GND23 P

160 GND24 P

165 GND25 P

166 GND26 P

183 GND27 P

184 GND28 P

197 GND29 P

198 GND30 P

193 VCC_RTC_3V P RTC 3.3V

205 5V_SB P Standby Power Supply +5VDC

206 5V_SB P

211 VCC1 P 5V supply

212 VCC2 P



213 VCC3 P

214 VCC4 P

215 VCC5 P

216 VCC6 P

217 VCC7 P

218 VCC8 P

219 VCC9 P

220 VCC10 P

221 VCC11 P

222 VCC12 P

223 VCC13 P

224 VCC14 P

225 VCC15 P

226 VCC16 P

227 VCC17 P

228 VCC18 P

229 VCC19 P

230 VCC20 P

16 NC

17 NC

22 NC

30 NC

32 NC

36 NC

38 NC

40 NC

64 NC

71 NC

75 NC

76 NC

77 NC

78 NC

79 NC

81 NC

83 NC



4.6 Hardware Operation Notes

a. Power prepare: Please confirm the power input is 12V. And the reference current is 1A. Make sure the power input positive is not reversed.

b. Environment: For the assembled or debug platform, be sure there hasn’t any risk of circuit shortness for the board. And make sure the anti static is done well.

c. Debug message view: Using COM port on P3 (COM1) to view the debug message. It will show the boot message. In PC side, communication hyper terminal or other serial software tools can be used. The debug port setting is: baud rate 115,200bps, NO hardware control, no ODD/EVEN checking, 1 Stop bit. Suggest use a cross cable, in two Female header.

138 NC

140 NC

154 NC

161 NC

162 NC

163 NC

164 NC

167 NC

168 NC

169 NC

170 NC

173 NC

175 NC

195 NC



5 Tips

Waste Disposal It is recommended to disassemble the device before abandoning it in conformity with local regulations.

Please ensure that the abandoned batteries are disposed according to local regulations on waste disposal. Do not throw batteries into fire (explosive) or put in common waste canister. Products or product packages with the sign of “explosive” should not be disposed like household waste but delivered to specialized electrical＆electronic waste recycling/disposal center. Proper disposal of this sort of waste helps avoiding harm and adverse effect upon surroundings and people’s health. Please contact local organizations or recycling/disposal center for more recycling/disposal methods of related products.

Comply with the following safety tips:

Do not use in combustible and explosive environment Keep away from combustible and explosive environment for fear of danger.

Keep away from all energized circuits. Operators should not remove enclosure from the device. Only the group or person with factory certification

is permitted to open the enclosure to adjust and replace the structure and components of the device. Do not change components unless the power cord is removed. In some cases, the device may still have residual voltage even if the power cord is removed. Therefore, it is a must to remove and fully discharge the device before contact so as to avoid injury.

Unauthorized changes to this product or its components are prohibited. In the aim of avoiding accidents as far as possible, it is not allowed to replace the system or change

components unless with permission and certification. Please contact the technical department of Vantron or local branches for help.

Pay attention to caution signs. Caution signs in this manual remind of possible danger. Please comply with relevant safety tips below each

sign. Meanwhile, you should strictly conform to all safety tips for operation environment.

Notice Considering that reasonable efforts have been made to assure accuracy of this manual, Vantron assumes

no responsibil ity of possible missing contents and information, errors in contents, citations, examples, and source programs.

Vantron reserves the right to make necessary changes to this manual without prior notice. No part of this manual may be reprinted or publicly released in forms of photocopy, tape, broadcast, e-document, etc.



US Office: Vantron Technology, Inc. Address: Address: 440 Boulder Court, Suite 300 Pleasanton, CA 94566 Tel: 916-202-7042 Email: [email protected]

China Office: Chengdu Vantron Technology, Ltd Address: 6rd floor, 1st build ing, No.9, 3rd WuKe East Street, WuHou District, Chengdu, P.R. China 610045 Tel: 86-28-8512-3930/3931, 8515-7572/6320 Email: [email protected]

mailto:[email protected]

mailto:[email protected]

vt-sbcq7-mx6q user’s manual (hardware)€¦ · imx31, imx53，imx6, samsung s3c6410, ti omap35xx...

Documents