VECTOR

SUPER SONIC AIR SCALER

SS17K SS17K-K / SS17K-M / SS17K-B

Thank you for purchasing the Vector Super Sonic air scaler, SS17K. Be sure to read this instruction manual thoroughly before use, for quality reassurance and longevity. Misuse of this instrument may cause severe damage or cause injury to the operator or patient. Specifications stated in this manual may be changed, improved or modified without prior notification. This instrument is for use by a trained dental professional to perform general dental scaling. Use of this instrument by any unauthorized personnel or for a use not intended may cause damage to the scaler or injury to the patient or operator.

SS17K is indicated as "scaler" in this instruction manual. MULTIflex® is a registered trademark of Kaltenbach & Voigt GmbH & Co. KG,

Biberach, Germany.

1. PREFACE -------------------------------------------------------------1

2. CAUTIONS FOR USE-----------------------------------------------2

3. INTENDED USE ------------------------------------------------------3

4. CHARACTERISTICS -------------------------------------------------3

5. DELIVERY PACKAGE-----------------------------------------------4

6. PART DESCRIPTION-------------------------------------------------5

7. HOW TO USE ---------------------------------------------------------6

7.2 How to attach and detach the scaling tip ------------8

9. CLEANING AND STERILIZATION -----------------------23

13. COMPONENT PARTS-------------------------------------35

12. SPECIFICATIONS-------------------------------------------34

10.1 Scaling tip replacement ----------------------------------27

11. TROUBLE SHOOTING--------------------------------------31

10.2 Power cartridge replacement ------------------29

7.3 How to attach to and detach from the coupling-127.4 Adjustment-------------------------------------------------------15

7.5 Scaling ---------------------------------------------------16

8.2 How to lubricate-----------------------------------------------19

7.1 Before use----------------------------------------------------------6

8. MAINTENANCE AND INSPECTION ---------------------18 8.1 How to drain ----------------------------------------------------18

8.3 How to dry scaling tip----------------------------------------228.4 Checking air compressor----------------------------22

9.1 Cleaning----------------------------------------------------------239.2 Sterilization -------------------------------------------------------24 9.3 Storage------------------------------------------------------------26

10. REPLACEMENT OF CONSUMABLE ITEMS ------------------27

Before reading this manual, recognize carefully the symbol marks shown in this manual which indicate "Most important points". "Most important points" describe the potentialities that may endanger the operator and patient. The conceivable possibilities, if the scaler is used without following instructions, are listed for your reference. The definitions in this instruction manual of the words preceded by the mark

are mentioned below. To avoid dangers, be

sure to observe the instructions preceded by these words. : This indicates not specific, general attentions, cautions and dangers. CONTRAINDICATION AND RESTRICTION

: This indicates exemptions from responsibilities such as improper use and excess of design limit. DANGER : This indicates potential direct dangers that may cause serious injuries, death, property damages such as total loss of the instrument or fire disaster. CAUTION : This indicates potential indirect dangers that may cause serious injuries, death, property damages such as total loss of the instrument or fire disaster. ATTENTION: This indicates potential dangers that may cause light to middle injuries, property damages such as partial loss of the instrument or loss of computer data. The drawings and illustrations in this instruction manual is SS17K-K unless otherwise specified.

CONTRAINDICATION AND RESTRICTION 1) This instrument must not be used by persons other than a trained dental professional, and for no purpose other than dental treatment. 2) Do not modify this instrument. 3) In case of trouble, ask your dealer for repair. 4) In case of deterioration or malfunction, do not use this instrument. 5) Do not use this instrument if it is not maintained or inspected properly. 6) Be sure to retain a copy of this manual and refer to it regularly for correct and safe use.

Contents SS17K-K/M/B 1 Scaling tip TTL1 1 Scaling tip TZ01 1 Scaling tip TES2 1 Tip replacement wrench 1 Flat wrench 1 Instruction manual 1

This air scaler is intended to remove dental plaque, calculus and stain from the tooth surface and tooth root by dental professionals only.

1) Due to reduced running noise compared to conventional air scalers, the operator can use the instrument much more comfortably. 2) Compact and handy, attaches directly to the dental unit. 3) More comfortable to sensitive patients who cannot stand the stimulus generated through the electric vibration power of an ultrasonic scaler. 4) Less heat build up a when compared to ultrasonic scalers, resulting in reduced cooling water spray. Provides the operator with better visibility of the treatment site. 5) The three-dimensional tip movement provides effective scaling while providing less damage to the tooth surface than ultrasonic scalers. 6) The power cartridge is easily and quickly replaceable at chairside. 7) As this scaler is driven by compressed air supplied from the dental unit, it does not affect other medical devices through electromagnetic waves (such as pacemakers). And it is not influenced by electromagnetic waves.

The following items are included in the delivery package. When opening, confirm whether all contents are included in the package. If something is missing, contact your dealer immediately.

Scaling tips

SS17K TTL1 (with green color O-ring)

TZ01 (with pink color O-ring)

Tip replacement wrench

TES2 (with light blue color O-ring)

Flat wrench

Front sheath Power Cartridge Main body

A T T E N T I O N The scaler, scaling tips and tip wrench are delivered “not sterile”. Sterilize them in an autoclave before first use.

7.1 Before use

ATTENTION Do not use this product for other purpose or in different ways from the instructions stated

in this manual. 1) Confirmation of contents

Please confirm the contents of package seeing " 5. DELIVERY PACKAGE ". 2) Checking scaler body Confirm the front sheath is firmly fixed in the main body. 3) Sterilization (Not Sterile – Sterilize prior to first use) According to instructions stated in " 9.

CLEANING AND STERILIZATION ", sterilize scaler, scaling tips and tip replacement wrench in an autoclave.

Drain the air filter of the air compressor in your dental office to supply the scaler with clean and dry air. Do not supply with compressed air containing moisture. For drainage and regular maintenance of your air compressor, please refer to air compressor's instructions manual.

5) Checking air compressor

According to the instructions stated in " 8.2 How to lubricate ", lubricate the scaler.

4) Lubrication (Lubricate prior to use, before autoclaving and if the scaler sits for more than 1 week)

7.2 How to attach and detach the scaling tip 1) Scaling tip Three scaling tips color-coded with O-rings are supplied as standard accessories. Select the suitable tip according to your treatment purpose.

TTL1 (with green color O-ring)

For supragingival and subgingival scaling.

TZ01 (with pink color O-ring)

For removing obstinate tar and stain adhesion.

TES2 (with light blue color O-ring) For scaling in crown interproximal, root proximal and crowding of teeth.

C A U T I O N 1) Be sure to use only original scaling tips. Use with non-original scaling tips may cause incomplete seating or irregular vibration of the scaling tip, which will cause accidents due to tip breakage. 2) Scaling tips must be attached firmly with the supplied tip replacement wrench. Confirm firm seating of the tip before every treatment. A loose scaling tip will unfasten during the treatment and cause accidents. 3) When detaching the tip from the scaler, be careful not to injure your fingers in order to avoid infection.

2) Attaching scaling tip a) Be sure to use sterilized scaling tips and wrench only. Put protective gloves on when attaching tip. b) Before attaching tip, make sure the scaler is disconnected from the coupling. If connected, disconnect the scaler from the coupling first. c) Insert a scaling tip into the tip replacement wrench. d) Align the scaling tip in the tip replacement wrench to the thread of the handpiece (power cartridge) and turn the tip replacement wrench in the direction of the arrow to tighten up the scaling tip. Do not apply excessive force. When attaching scaling tip, always hold the scaler main body, not the front sheath.

3) Detaching scaling tip a) Before detaching tip, make sure the scaler is disconnected from the coupling. If connected, disconnect the scaler from the coupling first.

b) Attach the replacement wrench onto the scaling tip. Turn the wrench in the direction of the arrow in the illustration until the scaling tip is detached from the handpiece. When detaching scaling tip, always hold the scaler’s main body, not the front sheath. c) Then detach the tip replacement wrench.

A T T E N T I O N 1) Do not tighten scaling tip excessively. 2) Depending on the scaling tip used and wear conditions, the scaler may generate running noise. Refrain from using the scaler for long periods of time, if the noise is loud.

7.3 How to attach and detach from the coupling

1) MULTIflex® coupling

Use a coupling compatible with the backend of this scaler. For attachment and detachment of the coupling, follow the instructions for use of the coupling. If the coupling has a light source, turn off the light of the coupling.

MULTIflex® coupling

C A U T I O N 1) Use a coupling compatible with the backend of this scaler. If an incompatible coupling is used, it may damage the scaler and the coupling or, cause the scaler to jump out of the coupling by the force of compressed air, which may result in an accident. (For MULTIflex® coupling) 2) Confirm that the connector of the turbine hose, coupling, and scaler are firmly set before use. If they are attached incompletely, they may jump out of the coupling by the force of compressed air, which may result in an accident. 3) While the scaler is in operation, never release the scaler from the coupling or turbine hose. The scaler may jump out of the connector by the force of compressed air, which may result in an accident.

A T T E N T I O N When using this scaler, turn off the light of the coupling. Otherwise the service life of the light source (bulb) in the coupling may be shortened.

2) MIDWEST 4 Hole and BORDEN 2 or 3 Hole a) Match the backend of scaler and connector holes. b) Rotate the nut ring to attach the scaler until it is fixed in the connector completely. c) Confirm secure installation of the scaler.

d) To detach the scaler from the turbine hose, rotate the nut ring in the opposite direction.

C A U T I O N 1) Be sure not to exceed the working air pressure of 0.3 MPa (45psi, 3.0 bar, 3.0 kgf/cm2 ). Use at an excessive air pressure causes damage on the tooth surface, patient discomfort, scaling tip breakage, and may shorten the life of the instrument. 2) After adjusting the power, grasp the strength using an extracted tooth prior to scaling.

7.4 Adjustment 1) Adjustment of air pressure a) Mount air pressure gauge between the scaler and coupling (MULTIflex® coupling) or turbine hose (MIDWEST 4 Hole and BORDEN 2 or 3 Hole). b) Stop water supply. Adjust air supply until the gauge shows 0.3MPa (45psi, 3.0 bar, 3.0 kgf/cm2 ). Do not exceed 0.3 MPa. c) Detach the pressure gauge and connect scaler to your coupling (MULTIflex® coupling) or turbine hose (MIDWEST 4 Hole and BORDEN 2 or 3 Hole) firmly.

A T T E N T I O N Depending on the scaling tip used, wear or use conditions, the scaler may generate running noise. Refrain from using the scaler long time, if the noise is loud.

C A U T I O N When scaling, supply plenty of water to cool the scaling tip and the tooth being scaled. If the water supply is not sufficient, it causes damages on tooth surface and premature wear of scaling tip.

2) Adjustment of water volume Depress the foot control of the unit and use water volume control of the unit or of the coupling to have adequate water volume. In doing this, follow the instructions for use of your unit or of your coupling. Each scaling tip has its water outlet at a different position. Before use, adjust the volume adequately so that water reaches around the edge of the scaling tip.

To avoid patient stimulus, injuries and scaling tip damage, scaling must be done with light touch. Select the most suitable tip according to the treatment purpose.

7.5 Scaling

C A U T I O N 1) To avoid infection, wear suitable protective masks, gloves and eyewear during use. 2) When scaling, supply plenty of water to cool the scaling tip and the tooth being scaled.

A T T E N T I O N 1) Do not apply scaling tip at the same treatment position for a long period of time. 2) Before starting treatment, check the depth of the periodontal pocket to prevent inserting the scaling tip too deeply, injuring the bottom of the pocket. 3) Supply plenty of water to provide an irrigation effect and prevent damages to the root of the tooth. 4) In case the scaler is activated in a periodontal pocket, check the depth of the pocket first. 5) Apply the scaling tip at the root’s surface in a parallel angle to the tooth’s axis. 6) Depending on the scaling tip used, wear or use conditions, the scaler may generate running noise. Refrain from using the scaler for a long period of time if the noise is loud, or it may affect hearing of the patient and operator.

A T T E N T I O N To use safely, inspect and maintain the scaler after clinic hours according to the instructions (See " 8. MAINTENANCE AND INSPECTION " ).

* Be sure to maintain the scaler and accessories after clinic hours according to the instructions below.

the scaler backend.

Drain the remaining water from the water line of the scaler by blowing compressed air with a three-way syringe from

2) Drainage 7.2 3) Detaching scaling tip ". Detach the scaling tip from the scaler in accordance with "

8.1 How to drain 1) Detaching scaling tip

SS17K-K SS17K-M SS17K-B

A T T E N T I O N 1) Be sure to drain the scaler before each sterilization and after clinic hours. 2) After draining, be sure to lubricate the scaler according to " 8.2 How to lubricate ".

8.2 How to lubricate 1) When to lubricate Use lubrication spray or oil for high speed air turbine handpiece. Lubrication must be done at the following cases:

. First use.

. Before sterilization by autoclave or chemical vapor sterilizer. . Twice a day after morning and afternoon clinic hours. . In case the scaler is not used more than one week. . After replacing the power cartridge.

A T T E N T I O N Be sure to lubricate the scaler according to " 8.2 How to lubricate ". Insufficient lubrication will cause damage or shorter life span of the scaler.

A T T E N T I O N 1) When lubricating with lubrication spray, be sure to hold the spray can upwards. If the can is held downwards, the spray spouts only the gas and the scaler will not be properly lubricated. 2) Insufficient lubrication will cause mechanical trouble or shorter life span of the scaler. 3) When using lubrication spray, read the cautions of the spray before use. 4) The scaler's vibration source (power cartridge) is made of metal and subject to rust. Insufficient lubrication and / or the supply of compressed air that contains excessive moisture (See " 8.4 Checking air compressor "), will cause premature decrease of treatment efficiency and vibration frequency due to rusting in the vibration source.

2) Detaching scaling tip Before lubrication, detach the scaling tip from the scaler in accordance with " 7.2 3) Detaching scaling tip ".

3) Lubrication (MULTIflex® coupling) a) Attach a nozzle compatible with the scaler backend to the lubricant spray. Oil b) Insert the nozzle of the spray into the scaler backend. Spray for 1 second holding the scaler firmly. c) After lubrication, connect the scaler to the coupling and run for one minute to penetrate the lubricant. Then wipe off excess lubricant with clean gauze or tissue.

SS17K-K

4) Lubrication (MIDWEST 4 Hole and BORDEN 2 or 3 Hole) a) When using lubrication spray, insert the nozzle into the drive air line at the scaler backend. Spray for about 1 second. b) When using high speed air turbine handpiece oil, place 4 drops of oil into the drive air line at the backend. c) After lubrication, connect the scaler to the turbine hose and run for one minute to penetrate the lubricant. Then wipe off excess lubricant with clean gauze or tissue. WE RECOMMEND VECTOR SPRAY – HIGHPERFORMANCE HANDPIECE LUBRICANT FOR THE SUPER SONIC AIR SCALER.

A T T E N T I O N 1) After use, remove the scaling tip from the scaler and dry the tip and the screw thread using three-way syringe air in order to prevent rusting. 2) The scaling tips are metal-made and subject to rust. Insufficient drying may cause rust, damage and accidents during treatment.

8.3 How to dry scaling tip 1) Detaching scaling tip

According to " 7.2 3) Detaching scaling tip ", detach scaling tip from the scaler. 2) Drying The following points must be dried well with air from three-way syringe. . Scaling tip surface and

spray hole. . Screw thread of the scaler nose

Drain the air filter of the air compressor in your dental office to supply the scaler with clean and dry air. Compressed air containing moisture can cause damage to the scaler. For drainage and regular maintenance of your air compressor, please refer to air compressor's instructions manual.

8.4 Checking the air compressor

C A U T I O N 1) Sterilization must be done after every patient in order to prevent direct and cross infection. 2) To avoid infection sterilization personnel should wear suitable protective mask, gloves, and eyewear on during each use.

9.1 Cleaning 1) Drainage of scaler

Drain the water line of the scaler according to " 8.1 How to drain " . 2) Cleaning Clean the saliva and blood from the scaler and scaling tips with alcohol. 3) Lubrication Lubricate the scaler according to " 8.2 How to lubricate ".

CAUTION To avoid infection, wear suitable protective mask, gloves and eyewear during use.

9.2 Sterilization * Sterilize the scaler, scaling tips and tip replacement wrench in autoclave. 1) Sterilization

Sterilization must be done after every patient. Put the scaler, scaling tips and tip replacement wrench into a proper sterilization bag separately. Place the sealed scaler, tips and wrench on a sterilization tray to avoid direct contact with sterilizer chamber surface, and put them into the autoclave. Sterilize at 121°C ( 250°F ) for 20 minutes ( EN554:1994 ) or at 132°C ( 270°F ) for 15 minutes ( JIS T 5910:2005 ) . The scaler is autoclavable up to 135°C ( 275°F ) . Follow your local regulations for sterilization. To prevent damaging scaler, skip the dry cycle.

2) After sterilization When the sterilization cycle is finished, remove the instruments from the autoclave immediately and air dry naturally. Be sure to dry completely.

A T T E N T I O N 1) When sterilizing, follow the instructions ( " 9. CLEANING AND STERILIZATION " ) to avoid trouble or damage of the scaler. 2) The maximum sterilization temperature is 135°C ( 275°F ). Autoclave at 121°C ( 250°F ) for 20 minutes ( EN554:1994 ) , or at 132°C ( 270°F ) for 15 minutes ( JIS T 5910:2005 ) . To prevent damaging scaler parts, skip the dry cycle. 3) Do not sterilize the scaler together with medicines or chemical adheres. 4) Do not soak the scaler in disinfectant liquid. 5) Do not use alkaline disinfectant, oxidized water or hard acid water. 6) Do not use dry heat sterilizer generating high heat, in order to avoid mechanical trouble or damage of the scaler. 7) If the scaler, scaling tips and tip replacement wrench are not dried well, it may cause rust or discoloration.

A T T E N T I O N 1) For depository, keep the instructions for storage (See " 9.3 Storage " ). 2) Store and take care of the scaler properly. Place the scaler beyond reach of persons other than dental professionals. 3) Do not store the scaler in a place where it may be exposed to water. 4) Keep the scaler in a place where it is not affected by barometric pressure, temperature, humidity, ventilation, strong sunshine, dust, salt or sulfurous air. 5) Keep the scaler in a place without vibration or shock. 6) Do not store the scaler in a place where chemical agents are kept or gas exists.

9.3 Storage After sterilization, dry the scaler, scaling tips and tip wrench naturally and completely. Keep them in the sealed sterilization bags.

C A U T I O N Scaling tips break easily and may cause unexpected accidents or injuries. Do not use broken, damaged or worn tips. Replace broken, damaged or worn tips immediately. This includes but is not limited to:* Tips worn through scaling.* Corroded or rusted tips. * Tips deformed on impact, e.g. dropped on the floor. * Sharpened, altered or deformed tips.

10.1 Scaling tip replacement 1) When to replace the scaling tip

Scaling tips will be worn out through normal use, which will effect scaler frequency and working efficiency.

2) How to check scaling tip wear a) Detach the scaling tip from the scaler. b) Put the scaling tip on the drawing to check the wear. c) If the tip is worn shorter than the marked line, it must be replaced. Use a new scaling tip.

3) How to replace the scaling tip a) Detach the scaling tip from the scaler according to " 7.2 3) Detaching scaling tip ". b) Check the scaling tip wear according to " 10.1 2) How to check scaling tip wear ". c) If the tip is to replace, attach new tip according to " 7.2 2) Attaching scaling tip ".

C A U T I O N 1) Prior to cartridge replacement, be sure to disconnect the scaler from the coupling and detach the scaling tip from the scaler. The scaler or front sheath may be ejected by the air pressure and cause accidents. 2) After cartridge replacement, check that the front sheath is firmly screwed in the main body. The scaler or front sheath may get ejected by the air pressure and cause accidents. 3) Do not disassemble the cartridge. If disassembled, the cartridge will be damaged and become unusable.

10.2 Power cartridge replacement tighten1) When to replace the cartridge

The cartridge will be worn out through normal use, which will effect scaler frequency and working efficiency. a) Check that the drive air supply is at proper air pressure of 0.3 MPa (45psi, 3.0 bar, 3.0kgf/cm2 ) at the coupling. b) Check the working efficiency using an extracted tooth. loosen2) How to replace the power cartridge a) Disconnect the scaler from the coupling. Detach the scaling tip from the scaler using the supplied flat wrench. b) Insert the flat wrench into the slit of the front sheath horizontally as shown in Fig. A. Turn the front sheath anticlockwise with the wrench to loosen it. When the front sheath has loosened, detach the flat wrench. c) Unscrew the front sheath with your fingers to remove it. d) Remove the worn power cartridge from the scaler main body as shown in Fig. B. e) Insert a new cartridge into the main body until fully seated. If it is not inserted properly, the front sheath won't be put in place. f) Screw the front sheath into the main body with your fingers until it stops.

Fig. A

Fig. B

g) Insert the flat wrench into the slit of the front sheath horizontally again as shown in Fig. A. Tighten the front sheath clockwise with the wrench firmly. h) Lubricate the scaler according to " 8.2 How to lubricate ".

C A U T I O N In case of malfunction, stop use immediately and contact your dealer in order to insure safe and proper operation.

Symptom Possible cause Countermeasures

1) No water supply.

* Water supply pedal of the dental unit is not pressed. * Water supply setting of the dental unit is inadequate. * Water does not come to the turbine hose. * Water line of the scaler is blocked.

* Press water supply pedal of the dental unit. * Open water supply valve of the dental unit. * Check water supply circuit of the dental unit. * Ask for repair.

In case of malfunction, check the symptom according to this trouble shooting before asking your dealer for repair or inspection.

Symptom Possible cause Countermeasures

2) No vibration or low power.

* No air supply. * Air line of the scaler is blocked. * Power cartridge is broken. * Immediately after lubrication(due to excess lubricant). * Dirt exists inside cartridge.

* Set the coupling pressure to 0.3MPa (45psi, 3.0 bar, 3.0 kgf/cm2 ). * Check the air at the coupling. If air comes to the coupling, ask for repair. * Replace with a new power cartridge. * Drive for 1min, after lubrication. * Lubricate the scaler.

3) Loud running noise.

* Loose scaling tip. * Scaling tip wear. * Power cartridge is broken. * Immediately after lubrication (due to excess lubricant).

* Tighten up with the supplied wrench. * Replace with a new scaling tip. * Replace with a new power cartridge. * Drive for 1min, after lubrication.

4) Leakage of air and water from around the coupling.

* Damage of O-ring and/or seal at the coupling.

* Replace the O-ring and/or seal at the coupling.

5) Tip cannot be attached.

* Non-original tip used. * Power cartridge is not installed in the scaler.

* Use original scaling tip. * Install power cartridge into the scaler.

Symptom Possible cause Countermeasures

6) Front sheath cannot be attached.

* Power cartridge is not installed properly.

* Insert the power cartridge into scaler main body until fully seated as shown in Fig. B of "10.2 Power cartridge replacement".

7) The scaler cannot attach to the coupling.

* Use of incompatible coupling. * Use a coupling compatible with this scaler.

Specifications

Product name SS17K Model SS17K-K SS17K-M SS17K-B Backend configuration MULTIflex®

coupling MIDWEST 4 Hole BORDEN 2 or 3 Hole Frequency 0 to 17,000 Hz Coupling pressure 0.3 MPa (45 psi, 3.0 bar, 3.0kgf/cm2) Air volume 22 L/min 23 L/min Cooling water volume 25 cc/min (Water pressure 0.2 MPa) Net weight (without scaling tip)

48 g (1.7 oz) 60 g (2.1 oz) 57 g (2.0 oz)

Total length (without scaling tip) 85 mm (3.3 inch) 115 mm (4.5 inch) 108 mm (4.3 inch)

REF 5011442 O-ring

REF 5011242 Scaling tip TTL1 REF 5031931

O-ring REF 1072291 REF 5011622 REF 5011292 Main body (K) REF 5065011

Front sheath O-ring O-ring Tip replacement

wrench REF 5037171 Scaling tip TZ01 (K)

REF 5022711 Power cartridge

Main body (4H) REF 5012022 REF 5011722

4-hole sealREF 5037191 O-ring Scaling tip TES2

REF 1072122 Front sheath (4/2H) REF 1072231 Main body (2H) REF 5012012 Flat wrench 2-hole seal

Distributor: Vector R & D Inc. 6824 19th St. #230, University Place, WA 98466, U.S.A. TOLL FREE: +1-877-88DRILL (+1-877-883-7455), Tel: +1-253-564-5084, Fax: +1-253-564-4927 Manufacturer:

MICRON Corporation 1-34-14, Higashiyukigaya, Ota-ku, Tokyo, 145-0065, Japan Tel: +81-3-3726-0396, Fax: +81-3-3726-5396

Made in Japan Patent pending M0802041DM-1-080205

刀䔀䘀. ...................